®
27
Multimeter
Users Manual
Mode d'Emploi
Bedienungs-Handbuch
Manuale d'Uso
Manual de Uso
For IEC 61010 CAT III Meters Only
October 1998 Rev . 2, 12/03
© 1998-2003 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
LIMI T ED WARRANTY & LIMITAT ION OF LIABILITY
Each Fluke 20, 70, 80, 170 and 180 Series DMM will be free from defects in material and workmanship for its lifetime. As used herein, “lifetime” is defined as seven
years after Fluke discontinues manufacturing the product, but the warranty period shall be at least ten years from the date of purchase. This warranty does not cover
fuses, disposable batteries, damage from neglect, misuse, contamination, alteration, accident or abnormal conditions of operation or handling, including failures
caused by use outside of the product’s specifications, or normal wear and tear of mechanical components. This warranty covers the original purchaser only and is not
transferable.
For ten years from the date of purchase, this warranty also covers the LCD. Thereafter, for the lifetime of the DMM, Fluke will replace the LCD for a fee based on
then current component acquisition costs.
To establish original ownership and prove date of purchase, please complete and return the registration card accompanying the product, or register your product
on http://www.fluke.com. Fluke will, at its option, repair at no charge, replace or refund the purchase price of a defective product purchased through a Fluke
authorized sales outlet and at the applicable international price. Fluke reserves the right to charge for importation costs of repair/replacement parts if the product
purchased in one country is sent for repair elsewhere.
If the product is defective, contact your nearest Fluke authorized service center to obtain return authorization information, then send the product to that service
center, with a description of the difficulty, postage and insurance prepaid (FOB Destination). Fluke assumes no risk for damage in transit. Fluke will pay retu rn
transportation for product repaired or replaced in-warranty. Before making any non-warranty repair, Fluke will estimate cost and obtain authorization, then invoice
you for repair and return transportation.
THIS WARRANTY I S YOUR ONLY REMEDY. NO OTHER WARRANTIES, SUCH AS FITNESS FOR A PARTICUL AR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE SHALL NOT BE LIABLE FOR ANY SPECIAL, INDI RECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR L OSSES, INCLUDING LOSS
OF DATA, ARISING FROM ANY CAUSE OR THEORY. AUTHORIZED RESELLERS ARE NOT AUTHORIZED TO EXTEND ANY DIFFERENT WARRANTY ON
FLUKE’S BEHALF. Since some states do not allow the exclusion or limitation of an implied warranty or of incidental or consequential damages, this limitation of
liability may not apply to you. If any provision of this warranty is held invalid or unenforceable by a court or other decision-maker of competent jurisdiction, such
holding will not affect the validity or enforceability of any other provision.
Fluke Corporation Fluke Europe B .V.
P.O. B ox 9090 P.O. B ox 1186
Everett WA 5602 B.D. Eindhoven
98206-9090 The Netherlands
Visit the Fluk e website at: www.fluke.com
Register your Meter at : regist er.fluke.com 2/02
i
Table of Contents
Title Page
Multimeter Safety........................................................................................................... 1
Operating Features........................................................................................................ 5
Applications................................................................................................................... 9
Voltage, AC/DC......................................................................................................... 9
Current, AC/DC......................................................................................................... 9
Resistance and Diode Test/Continuity...................................................................... 10
Resistance Measurement..................................................................................... 10
Diode Test and Continuity.................................................................................... 10
Conductance............................................................................................................. 11
Leakage Testing ....................................................................................................... 11
Analog Bar Graph Application ....................................................................................... 12
Using the Analog Bar Graph..................................................................................... 12
Specific Applications--Nulling.................................................................................... 13
Specific Applications--Contact Bounce..................................................................... 13
Specific Applications--Checking Capacitors.............................................................. 13
27
Users Manual
ii
Specific Applications--Noisy Resistance Measurements........................................... 16
Operator Maintenance................................................................................................... 16
Battery Installation or Replacement .......................................................................... 17
Fuse Test.................................................................................................................. 19
Fuse Replacement.................................................................................................... 19
General Maintenance................................................................................................ 20
Service........................................................................................................................... 22
Specifications................................................................................................................. 23
Multimeter Safety
1
Multimeter Safety
Read this information before using the meter. This meter
complies with EN 61010-1:1993, ANSI/ISA S82.01-1994
and CAN/CSR C22.2 No. 1010.1-92 Overvoltage
Category III. Use the meter only as specified in this Users
Manual, otherwise the protection provided by the meter
may be impaired.
A Warning identifies conditions and actions that
pose hazard(s) to the user.
A Caution identifies conditions and actions that
may damage the meter or the equipment under
test.
W Warnings
To avoid possible electric shock or personal
injury:
Inspect the meter before using it. Check
for cracks, missing plastic, or other
possible damage to the case. Make sure
that the insulation surrounding the
connectors is intact.
Inspect the test leads for damaged
insulation, exposed metal, and continuity.
Replace damaged test leads before using
the meter.
Do not use the meter if it operates
abnormally. Protection may be impaired.
When in doubt, have the meter serviced.
Do not operate the meter around
explosive gas, vapor or dust.
Do not apply more than the rated voltage
(1000 V) between terminals or between
any terminal and earth ground. The rated
voltage is marked on the meter.
Before each use, verify the meter’s
operation by measuring a known voltage.
Use only specified replacement parts.
Use caution when working above 30 V ac
rms, 42 V ac peak, or 60 V dc. Such
voltages pose a shock hazard.
When using the probes, always place
fingers behind the probe finger guards.
Connect the common test lead before
connecting the live test lead. When
disconnecting test leads, disconnect the
live test lead first.
Make sure the battery door is secured
before operating the meter.
27
Users Manual
2
Remove test leads from the meter before
opening the battery door.
Use only a properly installed, single 9 V
battery to power the meter.
Follow all equipment safety procedures.
Check the meter’s fuses (see “Testing the
Fuses”) before measuring current.
Never touch the probe to a voltage
source when the test leads are plugged
into the 10 A or 40 mA input jacks.
The use of makeshift fuses and the short-
circuiting of fuse holders is prohibited.
To avoid false readings, which could lead
to possible electric shock or personal
injury, replace the battery as soon as the
battery indicator (M) appears.
The meter is waterproof to a depth of 1
meter. Remove all surface water from the
product including water around, within
and under the rotary knob, input
receptacles and buttons prior to
connecting any voltages to the input.
International symbols used on the meter and in this
manual are explained in Table 1.
Multimeter Safety
3
Table 1. International Electrical Symbols
OOFF (power)
SWITCH POSITION GROUND
ON (POWER)
SWITCH POSITION SEE EXPLANATION IN
MANUAL
AC-ALTERNATING
CURRENT DOUBLE INSULATION
(Protection Class II )
DC-DIRECT CURRENT FUSE
EITHER DC OR AC BATTERY
27
Users Manual
4
Table 2. Input Terminals and Limits
Function Input Terminals
Red Lead Black Lead
Min Display
Reading Max Display
Reading Maximum Input
CI VOD COM 0.001 V 1000 V 1000 V
JF VOD COM 0.1 mV 320.0 mV 1000 V
O
(nS) VOD
VOD
COM
COM 0.1 e
0.01 nS 32.00 Me
32.00 nS 1000 V
1000 V
SVOD E 0.001 V 2.08 V 1000 V
A COM 0.01 A 20.00 A* 11 A 1000 V Fast Fuse**
AE U COM 0.01 mA 320.0 mA 44/100 A 1000 V Fast Fuse**
MN U COM 0.1 µA 3200 µA 44/100 A 1000 V Fast Fuse**
*10A continuous, 20A overload for 30 seconds maximum
**Fuse protected
Operating Features
5
Operating Features
The following features are keyed by number to the
illustration inside the front cover.
A Digital Display
3200 count, liquid crystal display with automatic decimal
point positioning. Updated two times per second. When
the meter is first turned on, all display segments appear
while the instrument performs a brief power-up self-test.
B Function Selector Rot ar y Swit ch
Turn to select any of 10 different functions, or OFF. Refer
to the Specifications for available ranges and to Table 2
for input terminals and limits.
CVolts dc
JMillivolts dc
IVolts ac
FMillivolts ac
OOhms (resistance), also conductance (1/e)
in nanosiemens (nS)
SContinuity or diode test
AMilliamps or amperes dc
MMicroamps dc
EMilliamps or amperes ac
NMicroamps ac
C TVolt, Ohm s , Diode Test Input
Terminal
Input terminal used in conjunction with the volts, mV (ac
or dc), ohms, or diode test position of the function
selector rotary switch.
D COM Com m on Ter minal
Common or return terminal used for all measurements.
E U Milliamp/M icroamp Input Ter minal
Input terminal used for current measurements up to 320
mA (ac or dc) with the function selector rotary switch in
the mA or µA positions.
F A Amperes Input Terminal
Input terminal used for current measurements up to 10A
continuous (20 A overload for 30 seconds) with the
27
Users Manual
6
function selector rotary switch in the mA/A position (ac or
dc).
G RANGE R Manual Range Mode
Pushbutton
Press once to enter manual range mode, press again to
increment range, press and hold for 2 seconds to return
to autorange. Meter returns to autorange if the function
selector is switched to any other position. There is no
autorange annunciator; absence of the manual range
annunciator indicates the meter is in autorange. If
RANGE is depressed (>1 second) while the function
switch is moved from OFF to any ON position, manual
ranging will be selected in all functions.
H REL L Relative Mode Pushbutt on
Press momentarily to enter the Relative mode and store
the displayed reading. The display will read zero. Press
again to update the stored digital reading. Press and hold
for 2 seconds to exit the Relative mode. The Relative
mode stores a digital reading and displays the change
(difference) between the stored reading and any following
reading. For example, if the stored reading is 15.00 V and
the present readings is 14.10 V, the display will indicate -
0.90V. The analog bar graph continues to display the
actual reading (14.10V). If the difference exceeds 3999
counts (without overloading the input), OF (overflow) is
displayed. The Relative mode selects manual ranging;
changing ranges automatically exits the Relative mode.
I MIN/MAX Mode Pushbutton
Press momentarily to enter MIN/MAX mode, press again
to toggle between MIN and MAX indications. Press and
hold for 2 seconds to exit MIN/MAX mode. The meter
stores the minimum and maximum digital readings, and
will display either reading as selected by the operator.
Press the HOLD/RESET button to reset the MIN/MAX
readings to the present input. The MIN/MAX mode
selects manual ranging; use a range that can record the
maximum anticipated input. Range changes reset
previously recorded MIN/MAX readings. Exiting the
MIN/MAX mode does not reset the previously recorded
readings unless the range or function is changed. The
MIN/MAX mode overrides the Touch Hold mode.
W Warning
To avoid electric shock or personal injury, do
not use Touch Hold to determine that
circuits with dangerous voltages are de-
energized. Touch Hold will not capture
unstable or noisy readings.
Operating Features
7
J HOLD H Touch Hold
Mode Pushbutton
Press momentarily to enter Touch Hold mode. In Touch
Hold, the meter captures a stable measurement and
holds it in the display. The operator can watch the probes
while taking measurements in difficult or hazardous
circuits, then look at the display when convenient. The
meter beeps and the display is automatically updated
each time a new, stable measurement is made. Press
momentarily to manually update reading. Press and hold
for 2 seconds to exit Touch Hold mode. If HOLD is
depressed (>1 second) while the function switch is moved
from OFF to any ON position, the Touch Hold mode will
only update to a new reading when the HOLD button is
pressed and automatic Touch Hold updates are
defeated. This is useful when you want to take a reading
at a specific time and hold it.
K MIN Minimum Annunciator
Indicates that the meter is in the MIN/MAX recording
mode, and the value displayed is the minimum digital
reading taken since reset or since entering MIN/MAX.
Refer to item 9 for operation.
L MAX Maximum Annunciator
Indicates that the meter is in the MIN/MAX recording
mode, and the value displayed is the maximum digital
reading taken since reset or since entering MIN/MAX.
Refer to item 9 for operation.
M L Relative Annunciator
Indicates that the meter is in the Relative mode and that
the value displayed is relative (the difference between the
present measurement and the previously stored reading).
Refer to item 8 for operation.
N H Touch Hold
Mode Annunciator
Displayed when the Touch Hold mode is in use. Refer to
item 10 for operation.
O Mke Resistance Annunciators
The and either the k or M is displayed for the
resistance range in use.
P nS Conductance Range Annunciator ( nS)
Top range of the resistance function is the conductance
range. Displays conductance in nS (nanosiemens). 1000
27
Users Manual
8
nS converts to megohms. (Example: 2 nS converts to 500
Me.) Use for measuring resistance above 32 megohms.
Select e, open test leads, press RANGE button twice.
Refer to item 7 for manual range operation.
Q Analog Bar Graph Display
Analog representation of input. Composed of 31
segments which illuminate starting from the left as the
input increases. (See display inside rear cover.) A minus
sign (-) is displayed for reverse-polarity inputs. Updated
25 times per second.
R Decimal Point/Range I ndicator
Decimal point position and the digits (3, 30, 300) under
the decimal point indicate the range in use.
S R Manual Range Annunciator
Displayed in the Manual Range mode or if the selected
function has only one range. Absence of the indicator
implies autorange mode in use. The meter powers-up in
autorange. In autorange, the meter automatically selects
the measurement range. Refer to item 7 for operation.
T M Low Battery Annunciator
Battery voltage is tested each time the function switch is
moved to a new position.
WWarning
To avoid false readings, which could lead to
possible electric shock or personal injury,
replace the battery as soon as the low
battery indicator (M) appears.
U Negative Polarity Annunciat o r
Automatically indicates negative input.
V Overload Indication
These symbols indicate the input is too large for the input
circuitry. (The location of the decimal point depends on
the measurement range.)
W Overflow Indication
These symbols indicate the calculated difference in the
Relative mode is too large to display (>3999 counts) and
that the input is not overloaded.
Applications
9
X Beeper (not illust r a t ed)
The beeper can produce beeps, clicks, or a cont inuous
tone. It is used for audible indication in the diode test
mode, when operating the push buttons, and when a new
reading is displayed in the Touch Hold mode.
Tilt Bail Adjustment
To use the tilt bail as a handle, lift the bail slightly (about
1 inch or 2.5 cm), pull the ends out and insert the ends in
the alternate set of holes.
Applications
Voltage, AC/DC
All ranges present an input impedance of approximately
10 megohms in parallel with less than 100 pF.
Measurement errors, due to circuit loading, can result
when making either ac or dc voltage measurements on
circuits with high source resistance. However, in most
cases the error is negligible (0.1% or less) if the
measurement circuit source resistance is 10 kilohms or
less.
When measuring voltages above 320 V in Touch Hold
mode, use manual ranging to minimize readings of stray
voltages.
Current, AC/DC
WWarning
To avoid electric shock or personal injury:
Never attempt an in-circuit current
measurement where the open-circuited
potential to earth is greater than 1000 V.
Before measuring current, check the
meter’s fuses (see “Testing the Fuses”).
Turn off circuit power before connecting
the meter in the circuit. Remember to
place the meter in series with the
current. Use proper terminals, function,
and range for your measurement.
To prevent arc blast and resulting injury,
install only the EXACT replacement fuse
listed in the Maintenance section.
All current ranges are fuse protected. Approximate
terminal resistances for the current ranges are: 0.1 ohms
for A, 5.6 ohms for mA, and 500 ohms for µA. The
voltage developed across the terminal resistance is
specified as burden voltage. If a fuse opens, refer to the
fuse replacement procedures in the Operator
Maintenance section of this manual.
27
Users Manual
10
Resistance and Diode Test/Continuity
Caution
To avoid possible damage to the meter or to
the equipment under test, disconnect circuit
power and discharge all high voltage
capacitors before measuring resistance,
testing for continuity, or diode test.
Resistance Measurement
Test lead resistance may influence measurement
accuracy on the 320-ohm range. To determine the error,
short the test leads together and read the lead
resistance. Correct the measurement by subtracting the
lead resistance from the measurement, or use the
Relative (REL) mode to zero the display. The error is
usually 0.1 to 0.2 ohms for a standard pair of test leads.
Some in-circuit resistance measurements can be made
without removing diodes and transistors from the circuit.
The full-scale measurement voltage produced on ranges
below 32 megohms does not strongly forward bias silicon
diodes or transistor junctions. Use the highest range you
can (except 32 megohm) to minimize the possibility of
turning on diodes or transistor junctions. Full scale
measurement voltage in the 32-megohm range does
strongly forward bias a diode or transistor.
Diode Test and Continuity
In diode test, there is only one range: 0 to +2.08 volts.
Voltage is developed across the component(s) under test
by a test current output from the Fluke 27. Voltages
greater than 2.08 V or open test leads produce an
overload (OL) condition. Negative inputs produce a
negative indication (they are not suppressed). In the
diode test function S the beeper produces a
continuous tone if the input is less than 0.1 V, and the
beeper beeps once when the input descends through a
0.7 V threshold.
Audible continuity testing is also performed with the
function selector switch in the diode test/continuity
position. A continuous tone sounds for test resistances
below approximately 270 ohms. An intermittent
connection produces erratic beeps, and can be valuable
troubleshooting aid. Erratic beeps can also occur, due to
environmental noise, if a test value is very close to the
threshold (270 ohms). Test resistances from
approximately 270 ohms to 2600 ohms produce a short
tone similar to a forward biased diode. Test resistances
less than approximately 36 kilohms will produce an on-
scale reading.
Applications
11
Conductance
Conductance measurement is performed with the
function selector switch in the ohms (e) function. The
conductance range can only be entered using manual
range selection; autorange cannot enter the conductance
range. The conductance range can be used both to
measure conductance (1/e, the inverse of resistance)
and to measure very high resistances (greater than 32
megohms).
High value resistance measurements are susceptible to
induced noise, and may require careful shielding.
Conductance measurements are displayed in
nanosiemens (nS). Calculate megohms by dividing 1000
by the nanosiemens displayed (1000/nS is equivalent to
megohms). Example: 2 nS converts to 500 megohms
(1000/2).
Leakage Testing
The conductance range effectively extends the resistance
measurement capability of the Fluke 27 to the point
where it can provide useful leakage measurements on
passive components. For example, the operator can
detect leaky diodes, cables, connectors, printed circuit
boards, etc. In all cases, the test voltage is less than 2 V
dc.
Leakage testing on purely resistive components such as
cables and printed circuit boards is straightforward.
Select the ohms function and manually increment the
range to conductance (nS). Connect the test leads to the
test points (nS). Connect the test leads to the test points
on the unit under test, and read the leakage in terms of
conductance.
Note
There is normally a small residual reading with
open test leads in the conductance range. To
ensure accurate measurements, connect clean
test leads to the Fluke 27, and (with the leads
open) read the residual leakage in
nanosiemens. Correct subsequent
measurements by subtracting the residual from
the readings. This can be done automatically
using the Relative mode (REL).
Diode leakage tests require that the diode junction be
reverse biased when being measured. This is
accomplished by connecting the anode of the diode to
the COMMON input terminal and the cathode (ring) of the
diode to the volts/ohms/diode test terminal. Leakage at
the test voltage being applied can then be read in terms
of conductance.
27
Users Manual
12
High-voltage stacked diode assemblies can usually be
tested for forward and reverse resistance changes using
conductance. These assemblies typically have such high
forward voltage drops that the diode test or resistance
modes cannot test them.
Analog Bar Graph Application
In looking at the analog bar graph, notice that it is
composed of segments that simulate an analog needle.
The bar graph performs the same function as an analog
meter needle, but it eliminates the mechanical overshoot
inherent in needle movements.
A negative (-) annunciator is displayed at the left end of
the bar graph when taking a reverse polarity dc
measurement. Assume that a slowly varying dc voltage is
the input signal. As the input goes more positive (from
zero), a bar graph segment is displayed, and additional
segments are displayed from left to right, to indicate the
input level as it increases. Now, assume that the input
level slowly decreases. Fewer bar graph segments are
displayed as the signal decreases, then the - annunicator
flashes as the signal level passes through 0. As the
signal goes more negative, the - annunciator is displayed
from left to right, indicating a more negative input signal.
The first segment is an indication greater than or equal to
20 counts.
Note that every fifth segment of the bar graph is slightly
larger than those in between, and every tenth segment is
larger yet. These larger segments provide a quick
reference for bar graph indications. The largest segments
(every 10th segment) divide the display into thirds. Thus,
if the bar graph indicates 11 segments on the 32.00V
range, the input voltage is 10 to 11 volts; if the bar graph
indicates 11 segments on the 320.0V range, the input
voltage is 100 to 110 volts. If the input equals or exceeds
3000 counts on the range selected, the bar graph
displays, an arrow at the far right of the display. If the
manual range annunciator (R) is not displayed, the Fluke
27 automatically switches to the next high range if the
input exceeds approximately 3260 counts
Using the Analog Bar Graph
The analog bar graph is most useful in making
adjustments and performing limited diagnostics. Bar
graph response is fast and precise, so it can be used to
easily reach a setting within a few percent of the final
adjustment. The bar graph can be used to make rough
adjustments quickly; then the 3200-count digital display
can be used for final adjustment.
The analog bar graph is useful for performing limited
diagnostics in applications were rapidly fluctuating signal
levels cause the flashing digits of a digital display to be
useless. Like the traditional VOM needle, the analog bar
Analog Bar Graph Application
13
graph excels at displaying trends, or slowly changing
signals. In addition, autoranging on the Fluke 27 allows
monitoring the signal change through changing ranges.
Many diagnostic routines using the bar graph require
practice. The operator is looking for good or bad signal
patterns that occur over some span of time. Capacitance
checks and noisy resistance measurements create such
patterns. Therefore, familiarity with analog bar graph
response and movement is necessary to accurately
interpret a signal pattern. Compare the bar graph
response when making measurements on a known-good
unit to the bar graph response when making
measurements on a faulty unit.
Specific Applications--Nulling
The Fluke 27 bar graph is ideal for nulling adjustments.
As an adjustment approaches zero, fewer bar graph
segments are displayed, then no bar graph segments are
displayed. The - annunciator flickers when the input level
is within 10 counts to zero. The flickering null indication is
displayed every time the input approaches zero or swings
from one polarity to the other. The operator merely
watches for the - annunicator indication, then reverses
the direction of the adjustment when the polarity sign is
displayed. In one or two passes, a near-zero input level is
possible, then the digital display can be used for exact
zero adjustment.
Specific Applic ations--Contact Bounce
When subject to vibration, relay contacts may begin to
bounce open. Checking for this intermittent problem is a
routine troubleshooting measure associated with many
types of equipment, including computers. Since the
bounce problem will worsen as the relay fatigues, early
diagnosis is important.
When the contact bounces open, its resistance value
changes momentarily from zero to infinity and back.
Ordinary hand-held DMMs take more than 300
milliseconds to update their displays--much too long to
detect a brief contact bounce. A traditional VOM needle
will move slightly at the instant of contact bounce, but the
inertia of the needle movement dampens the response.
The analog bar graph, however, will display at least one
segment the moment the contact opens. The bar graph
can detect contact bounce as brief as 0.2 milliseconds,
while most analog needle movements require a 3
millisecond opening before they will respond.
Specific Applications--Checking Capacitors
Volt-ohm meters are often used as simple capacitor
checkers. In the capacitor kick test, the needle of the
VOM in the resistance mode moves quickly from open
(infinite ohms) toward short (zero ohms) as the capacitor
is placed across the VOM input. The VOM battery
27
Users Manual
14
charges the capacitor and the needle slowly moves back
to the open (infinite ohms) position. The higher resistance
ranges offer increased sensitivity for checking smaller
capacitors.
The analog bar graph can make similar checks in the
resistance function, even in the autoranging mode. As a
capacitor is placed across the inputs, the analog bar
graph quickly shortens, then rapidly down-ranges,
depending on the size of the capacitor. As the capacitor
charges, the bar graph slowly extends back to its full 31-
segment length, up-ranging if necessary. For capacitors
as small as 0.1µF, only the 32-megohm range is involved.
In a fixed range (using manual range mode), the time it
takes for the bar graph to extend from zero to full scale
indicates the approximate capacitance value. Table 3
gives typical capacitance values for various charge times
on different resistance ranges. For very small capacitors,
use the conductance (nS) mode.
Analog Bar Graph Application
15
Table 3. Capacitance Vs. Time to Full Scale
Capacitance Resistance Range
Value 320 e3.2 ke32 ke320 ke3.2 Me32 Me
10,000 µF 4 sec 33 sec 5 min ext ext ext
1,000 µF nil 4 sec 30 sec ext ext ext
100 µF nil nil 3 sec 28 sec ext ext
10 µF nil nil nil 3 sec 25 sec ext
1 µF nil nil nil nil 2 sec 15 sec
0.1 µF nil nil nil nil nil 2 sec
ext = extended time, nil = no indication
27
Users Manual
16
Specific Applications--Noisy Resistance
Measurements
Most digital multimeters are so sensitive they can not
tolerate as much as 50 mV of the line noise while making
resistance measurement; their digital displays become
unreadable due to the line noise. On the other hand,
because of the mechanical inertia of the analog needle,
the noise alternately pulls the needle to the left and then
to the right, averaging out any movement and leaving a
fairly stable resistance reading.
The Fluke 27 resistance measurement circuit is designed
to tolerate ac noise far better than the usual DMM.
Readable 2-kilohm readings can be obtained even in the
presence of 1 V ac noise. Readings of 1 megohm may be
obtained with up to 2 V ac noise. The noise appears as
about 50 counts of change and an oscillating bar graph.
Operator Maintenance
WWarnings
To avoid possible electric shock or personal
injury:
Do not allow water to get inside the case.
Remove any input signals prior to
removing test leads and opening case.
When servicing the meter, use only
specified replacement parts.
Before closing battery door, make sure
fuse cover is in place.
Make sure the battery door is closed and
latched before you operate the meter.
To prevent arc blast and resulting injury,
install only the EXACT replacement fuse
listed in the Maintenance section.
Operator Maintenance
17
Battery Installation or Replacement
A single 9V battery (NEDA 1604, 6F22, or 006P) supplies
power to operate the Fluke 27. Referring to Figure 1, use
the following procedure to replace the Fluke 27 battery:
1. Turn the rotary switch to OFF, and remove the test
leads.
2. Lift the instrument stand on the back of the Fluke 27,
then remove the four black, #6 X 32, Pozi-drive
screws from the battery cover.
3. Pull the battery cover straight out from the back of
the meter. (A coin-slot in the side of the battery cover
facilitates removal.)
4. Remove and disconnect the battery.
5. Snap the battery connector to the terminals on the
new battery, then slide the battery into the battery
compartment.
6. Insert the battery spacer/cover into the Fluke 27,
then start the four screws removed in step 2. Press
firmly on the battery cover while tightening the
screws in a diagonal pattern.
27
Users Manual
18
Fuse cover
Battery cover
Battery
Battery
connector
F2
F1
ye1f.eps
Figure 1. Battery and Fuse Replacement
Operator Maintenance
19
Fuse Test
WWarnings
To avoid possible electric shock or personal
injury:
Remove the test leads and any input
signals before replacing battery or fuses.
Before closing battery door, make sure
fuse cover is in place.
Make sure the battery door is closed and
latched before you operate the meter.
To prevent arc blast and resulting injury,
install only the EXACT replacement fuse
listed in Table 4.
1. Turn the function selector switch to the position.
2. Connect a test lead from the T input terminal
to the A input terminal.
3. The display should indicate between 0.1 ohm and
0.3 ohm. This tests F2 (11A, 1000V fast).
4. Move one end of the test lead from the A input
terminal to the mA/µA input terminal.
5. The display should indicate between 5.3 ohms and
6.0 ohms. This tests F1 (44/100A, 1000V fast.
6. If either of the above display indications is OL
(overload), replace the appropriate fuse.
Fuse Replacement
WWarning
To avoid personal injury, do not use
makeshift fuses or short-circuit the fuse
holders.
Referring to Figure 1, use the following procedure to
check or replace the Fluke 27 fuses:
1. Perform steps 1 through 4 of the battery replacement
procedure.
2. Pull the fuse cover down, then out of the meter.
3. Remove the defective fuse (or check continuity
through the suspected fuse), and if necessary install
a new fuse of the same size and rating.
4. Snap the fuse cover back into place.
5. Reinstall the battery spacer/cover as instructed in
step 6 of the battery replacement procedure.
27
Users Manual
20
Table 4. Replacement Fuses
Item Description PN Qty
F1
W
Fuse, F44/100A,
1000 VAC/DC 943121 1
F2
W
Fuse, F11A, 1000
VAC/DC 803293 1
W To ensure safety, use exact replacement only
General Maintenance
Clean the case with a damp cloth and detergent; do not
use abrasives or solvents.
The Fluke 27 is sealed to protect the instrument. To
maintain proper sealing, open only the battery/fuse
compartment.
Have the meter calibrated and the seals (part number
738112) replaced by a qualified technician once a year to
ensure specified performance. Contact the nearest Fluke
Service Center or refer to the Fluke 27 Service Manual
(part number 690206) for calibration or repair. Refer to
Table 5 for replaceable parts.
Table 5. Replaceable Parts
Item Description PN Qty
BT1 Battery, 9V 696534 1
H6 Screw, PH 6-32 x 3/8 682070 4
MP11 Foot, Case 654335 1
MP12 Bail, Tilt (Bracket) 744474 1
MP14 Cover, Battery 670585 1
MP15 O-Ring, Battery 697185 1
MP16 Spacer, Battery 665023 1
MP61 Fuse Cover 665031
TL75* Test Lead Set 1
AC72* Allicator Clip Set 1
TM1 Users Manual 690203 1
TM2 Service Manual 690206 1
*Accessor y Number
Operator Maintenance
21
MP12
F1
F2
MP61
MP15
MP16
MP14
H6
BT1
MP11 TL75
Test Lead Set
AC72
Alligator Clips
ye2c.eps
Figure 2. Replaceable Parts
27
Users Manual
22
Service
To contact Fluke, call one of the following telephone
numbers:
USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-356-5500
Or, visit Flukes Web site at www.fluke.com.
Specifications
23
Specifications
Function Range Resolution Accuracy*
3.200 V 0.001 V ±(0.1%+1)
C32.00 V 0.01 V ±(0.1%+1)
320.0 V 0.1 V ±(0.1%+1)
1000 V 1 V ±(0.1%+1)
J320.0 mV 0.1 mV ±(0.1%+1)
320.0 e0.1 e±(0.3%+3)**
3.200 ke0.001 ke±(0.2% +1)
O32.00 ke0.01 ke±(0.2% +1)
(nS) 320.0 ke0.1 ke±(0.2% +1)
3.200 Me0.001 Me±(0.2% +1)
32.00 Me0.01 Me±(1%+1)
32.00 nS 0.01 nS ±(2%+10)
S2.080 V 0.001 V ±(1%+1) typical
40 Hz-2 kHz 2 kHz-10 kHz 10 kHz-30 kHz
3.200 V 0.001 V ±(0.5%+3) ±(2%+3) ±(4%+10)
I32.00 V 0.01 V ±(0.5%+3) ±(2%+3) ±(4%+10)
320.0 V 0.1 V ±(0.5%+3) ±(2%+3) ±(4%+10)
1000 V 1 V ±(1%+3) ±(3%+3) Not Specified
F320.0 mV 0.1 mV ±(0.5%+3) ±(2%+3) ±(4%+10)
** When using the REL () function to compensate for offsets
27
Users Manual
24
Function Range Resolution Accuracy Typical Burden Voltage
32.00 mA 0.01 mA ±(0.75%+2) 5.6 mV/mA
A320.0 mA 0.1 mA ±(0.75%+2) 5.6 mV/mA
10.00 A 0.01 A ±(0.75%+2) 50 mV/A
M320.0 µA 0.1 µA ±(0.75%+2) 0.5 mV/µA
3200 µA 1 µA ±(0.75%+2) 0.5 mV/µA
E32.00 mA 0.01 mA ±(1.5%+2) 5.6 mV/mA
40-1000 Hz 320.0 mA 0.1 mA ±(1.5%+2) 5.6 mV/mA
10.00 A 0.01 A ±(1.5%+2) 50 mV/A
N320.0 µA 0.1 µA ±(1.5%+2) 0.5 mV/µA
40-1000 Hz 3200 µA 1 µA ±(1.5%+2) 0.5 mV/µA
* Accuracy is specified as ±([% of reading] + [number of least significant digits]).
Basic electrical accuracy is specified from 18°C to 28°C with relative humidity up to 95%, for a period of one year after
calibration. All ac conversions are ac coupled, average responding, and calibrated to read the true rms value of a sine wave
input.
Ranging is either automatic or manual in all functions with more than one range. Test resistance below approximately 270 e
in the Diode test function produces a continuous audible tone.
Specifications
25
Function Overload
Protection* Input Impedance
(Nominal) Common Mode Rejection Ratio
(1 ke unbalance) Normal Mode Rejection
C1000 V rms 10 Me in // with<100 pF >120 dB at dc, 50 Hz, or 60 Hz >60 dB at 50 Hz or 60 Hz
J1000 V rms 10 Me in // with<100 pF >120 dB at dc, 50 Hz, or 60 Hz >60 dB at 50 Hz or 60 Hz
I1000 V rms 10 Me in // with<100 pF
(ac coupled) >60 dB, dc to 60 Hz
F1000 V rms 10 Me in // with<100 pF
(ac coupled) >60 dB, dc to 60 Hz
Open Circuit Test Voltage Full Scale Voltage
O1000 V rms Up to 3.2 Me32 Me or nS
<2.8 V dc <420 mV dc <1.3 V dc
*107 V Hz Max
Maximum Voltage Between Any
Terminal and Earth Ground Function Fuse Protection
1000 V mA or µA
A44/100 A 1000 V Fast
11 A 1000 V FasT
27
Users Manual
26
Digital
Display
......................................................................
3200 counts, updates 2/sec
Analog
Display
.....................................................................
31 Segments, updates 25/sec
Operating
.......................................................
-15°C to 55°C, to -40°C for 20 minutes when taken from
20°C
Storage Temperature
Without
Battery .................................................................
With
Battery ......................................................................
-55°C to 85°C
-55°C to 60°C
Electromagnetic
Compatibility
...........................................
In an RF field of 3 V/m on all ranges and functions except
mVAC
, total accuracy = specified accuracy +1.0% of range.
For mVAC, total accuracy = specified accuracy + 1.5% of
range. EN 61326-1:1997
Temperature Coefficient...................................................... 0.1X (specified accuracy)/ °C (<18°C or >28°C)
Relative
Humidity
.................................................................
0% to 95% (0°C to 35°C)
0% to 70% (35°C to 55°C)
Battery
Type
.........................................................................
9 V, NEDA 1604 or 6F22 or 006P
Battery
Life
...........................................................................
1000 hrs. typical
Shock, Vibration and Water
Resistance
............................
Per MIL-T-28800 for a Style A, Class 2 Instrument
Size (H X W X
L )
..................................................................
2.2 in X 3.75 in X 8 in (5.6 cm X 9.5 cm X 20.3 cm)
Weight
...................................................................................
1.6 pounds (0.75 kg)
Altitude
.................................................................................
Safety
....................................................................................
2000 m maximum
Complies with ANSI/ISA S82.01-1994, CAN/CSA C22.2 No.
1010.1:1992, 1000 V Overvoltage Category III. UL3111-1.