MAX3051ESA+ - MAXIM INTEGRATED PRODUCTS

General Description

The MAX3051 interfaces between the CAN protocol

controller and the physical wires of the bus lines in a

controller area network (CAN). The MAX3051 provides

differential transmit capability to the bus and differential

receive capability to the CAN controller. The MAX3051

is primarily intended for +3.3V single-supply applica-

tions that do not require the stringent fault protection

specified by the automotive industry (ISO 11898).

The MAX3051 features four different modes of opera-

tion: high-speed, slope-control, standby, and shutdown

mode. High-speed mode allows data rates up to

1Mbps. The slope-control mode can be used to

program the slew rate of the transmitter for data rates of

up to 500kbps. This reduces the effects of EMI, thus

allowing the use of unshielded twisted or parallel cable.

In standby mode, the transmitter is shut off and the

receiver is pulled high, placing the MAX3051 in low-

current mode. In shutdown mode, the transmitter and

receiver are switched off.

The MAX3051 input common-mode range is from -7V to

+12V, exceeding the ISO 11898 specification of -2V to

+7V. These features, and the programmable slew-rate

limiting, make the part ideal for nonautomotive, harsh

environments. The MAX3051 is available in 8-pin SO

and SOT23 packages and operates over the -40°C to

+85°C extended temperature range.

Applications

Printers JetLink

Industrial Control and Networks

Telecom Backplane

Consumer Applications

Features

♦Low +3.3V Single-Supply Operation

♦ESD Protection

±12kV Human Body Model

♦Wide -7V to +12V Common-Mode Range

♦Small SOT23 Package

♦Four Operating Modes

High-Speed Operation Up to 1Mbps

Slope-Control Mode to Reduce EMI (Up to 500kbps)

Standby Mode

Low-Current Shutdown Mode

♦Thermal Shutdown

♦Current Limiting

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

________________________________________________________________ Maxim Integrated Products 1

CANL

SHDNRXD

CANHGND

VCC

TXD

SO/SOT23

TOP VIEW

MAX3051

Pin Configuration

Ordering Information

19-3274; Rev 1; 6/05

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

Typical Operating Circuit at end of data sheet.

PART TEMP RANGE PIN-

PACKAGE

TOP

MARK

MAX3051ESA -40°C to +85°C 8 SO —

MAX3051EKA-T -40°C to +85°C 8 SOT23-8 AEKF

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

2 _______________________________________________________________________________________

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(VCC = +3.3V ±5%, RL= 60Ω, CL= 100pF, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA=

+25°C.) (Note 1)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

VCC to GND..............................................................-0.3V to +6V

TXD, RS, SHDN to GND ...........................................-0.3V to +6V

RXD to GND .............................................................-0.3V to +6V

CANH, CANL to GND..........................................-7.5V to +12.5V

Continuous Power Dissipation (TA= +70°C)

8-Pin SO (derate 5.9mW/°C above +70°C)...................470mW

8-Pin SOT23 (derate 9.7mW/°C above +70°C).............774mW

Operating Temperature Range ...........................-40°C to +85°C

Maximum Junction Temperature .....................................+150°C

Storage Temperature Range .............................-65°C to +150°C

Lead Temperature Range (soldering, 10s)......................+300°C

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Dominant 35 70

Recessive 2 5 mA

Supply Current IS

Standby 8 15 µA

Shutdown Current ISHDN VSHDN = VCC, TXD = VCC or floating 1 µA

Thermal-Shutdown Threshold VTSH +160 °C

Thermal-Shutdown Hysteresis 25 °C

TXD INPUT LEVELS

High-Level Input Voltage VIH 2VCC +

0.3V V

Low-Level Input Voltage VIL 0.8 V

Input Capacitance CIN 5pF

Pullup Resistor RINTXD 50 100 kΩ

CANH, CANL TRANSMITTER

VTXD = VCC, no load 2 2.3 3 V

Recessive Bus Voltage VCANH,

VCANL VTXD = VCC, no load, VRS = VCC

(standby mode) -100 +100 mV

Off-State Output Leakage -2V < VCANH, VCANL < +7V, SHDN = HIGH -250 +250 µA

Input Leakage Current VCC = 0V, VCANH = VCANL = 5V -250 +250 µA

CANH Output Voltage VCANH VTXD = 0V 2.45 V

CANL Output Voltage VCANL VTXD = 0V 1.25 V

VTXD = 0V 1.5 3.0

VTXD = 0V, RL = 45Ω1.2 3.0 V

VTXD = VCC, no load -500 +50

Differential Output (VCANH -

VCANL)

VTXD = VCC, RL = 60Ω-120 +12 mV

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

_______________________________________________________________________________________ 3

ELECTRICAL CHARACTERISTICS (continued)

(VCC = +3.3V ±5%, RL= 60Ω, CL= 100pF, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA=

+25°C.) (Note 1)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

-7V ≤ VCANH ≤ 0V -200

CANH Short-Circuit Current ICANHSC Minimum foldback current -35 mA

CANL Short-Circuit Current ICANLSC VCC ≤ VCANL ≤ 12V 200 mA

RXD OUTPUT LEVELS

RXD High Output-Voltage Level VOH I = -1mA 0.8 x

VCC VCC V

RXD Low Output-Voltage Level VOL I = 4mA 0.4 V

D C BU S R EC EI VER ( VT XD

= VC C

; C A N H a n d C A N L e x t e r n a l l y dr iv e n ; - 7 V ≤ VC A N H

, VC A N L ≤ + 1 2 V, un le s s ot h e r w i s e sp e c if i e d )

-7V ≤ VCM ≤ +12V 0.5

Differential Input Voltage

(Recessive) VDIFF VRS = VCC (standby mode) 0.5 V

Dominant 0.9

Differential Input Voltage

(Dominant) VDIFF VRS = VCC (standby mode) 1.1 V

Differential Input Hysteresis V

D IF F

(

H Y S T

)

20 mV

CANH and CANL Input

Resistance RI20 50 kΩ

Differential Input Resistance RDIFF 40 100 kΩ

MODE SELECTION (RS)

Input Voltage for High Speed VSLP 0.3 x

VCC V

Input Voltage for Standby VSTBY 0.75 x

VCC V

Slope-Control Mode Voltage VSLOPE RRS = 25kΩ to 200kΩ0.4 x

VCC

0.6 x

VCC V

High-Speed Mode Current IHS VRS = 0 -500 µA

SHUTDOWN (SHDN)

SHDN Input Voltage High VSHDNH 2V

SHDN Input Voltage Low VSHDNL 0.8 V

SHDN Pulldown Resistor RINSHDN 50 100 kΩ

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

4 _______________________________________________________________________________________

Note 1: All currents into device are positive; all currents out of the device are negative. All voltages are referenced to device

ground, unless otherwise noted.

Note 2: No other devices on the BUS.

Note 3: BUS externally driven.

TIMING CHARACTERISTICS

(VCC = +3.3V ±5%, RL= 60Ω, CL= 100pF, TA= TMIN to TMAX, unless otherwise noted. Typical values are at VCC = +3.3V and TA=

+25°C.)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

VRS = 0V (≤1Mbps) 50

RRS = 25kΩ (≤500kbps) 183

Delay TXD to Bus Active

(Figure 1) tONTXD

RRS = 100kΩ (≤125kbps) 770

VRS = 0V (≤1Mbps) 70

RRS = 25kΩ (≤500kbps) 226

Delay TXD to Bus Inactive

(Figure 1) tOFFTXD

RRS = 100kΩ (≤125kbps) 834

VRS = 0V (≤1Mbps) 80

RRS = 25kΩ (≤500kbps) 200

Delay Bus to Receiver Active

(Figure 1) tONRXD

RRS = 100kΩ (≤125kbps) 730

VRS = 0V (≤1Mbps) 100

RRS = 25kΩ (≤500kbps) 245

Delay Bus to Receiver Inactive

(Figure 1) tOFFRXD

RRS = 100kΩ (≤125kbps) 800

VRS = 0V (≤1Mbps) 96

RRS = 25kΩ (≤500kbps) 12.5

RRS = 100kΩ (≤125kbps) 2.9

Differential-Output Slew Rate SR

RRS = 200kΩ (≤62.5kbps) 1.6

V/µs

Bus Dominant to RXD Active tDRXDL VRS > 0.8 x VCC, standby, Figure 2 1 µs

Standby to Receiver Active tSBRXDL BUS dominant, Figure 2 4 µs

SHDN to Bus Inactive tOFFSHDN TXD = GND, Figure 3 (Note 2) 1 µs

S H DN to Recei ver Acti ve tONSHDN BUS dominant, Fi gur e 3 (Note 3) 4 µs

S H D N to S tand b yt

SHDNSB Fi g ur e 4 20 µs

ESD Protection Human Body Model ±12 kV

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

_______________________________________________________________________________________ 5

TXD

VDIFF

0.9V

RXD

0.5V

VCC/2 VCC/2

tONTXD

tONRXD

tOFFTXD

tOFFRXD

VCC/2 VCC/2

VDIFF tSBRXDL

tDRXDL

1.1V

RXD

BUS EXTERNALLY

DRIVEN

VCC x 0.75

VCC/2 VCC/2

SHDN

VDIFF

tOFFSHDN tONSHDN

RXD

BUS EXTERNALLY

DRIVEN

VCC/2

0.5V

Figure 1. Timing Diagram Figure 2. Timing Diagram for Standby Signal

Figure 3. Timing Diagram for Shutdown Signal

0.75V × VCC

SHDN

VCC/2

tSHDNSB

Figure 4. Timing Diagram for Shutdown-to-Standby Signal

Timing Diagrams

SLEW RATE vs. RRS AT 100kbps

MAX3051toc01

RRS (kΩ)

SLEW RATE (V/µs)

18016014012010080604020

0200

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

6 _______________________________________________________________________________________

SUPPLY CURRENT vs. DATA RATE

MAX3051toc02

DATA RATE (kbps)

SUPPLY CURRENT (mA)

800600400200

0 1000

TA = +25°C

TA = -40°C

TA = +85°C

SHUTDOWN SUPPLY CURRENT vs.

TEMPERATURE (SHDN = VCC)

MAX3051toc03

TEMPERATURE (°C)

SHUTDOWN SUPPLY CURRENT (nA)

603510-15

100

120

-40 85

STANDBY SUPPLY CURRENT vs.

TEMPERATURE (RS = VCC)

MAX3051toc04

TEMPERATURE (°C)

STANDBY SUPPLY CURRENT (µA)

603510-15

8.5

9.0

9.5

10.0

10.5

11.0

8.0

-40 85

RECEIVER PROPAGATION DELAY vs.

TEMPERATURE

MAX3051toc05

TEMPERATURE (°C)

RECEIVER PROPAGATION DELAY (ns)

603510-15

-40 85

RRS = GND

RECESSIVE

DOMINANT

DRIVER PROPAGATION DELAY vs.

TEMPERATURE

MAX3051toc06

TEMPERATURE (°C)

DRIVER PROPAGATION DELAY (ns)

603510-15

-40 85

RRS = GND, DATA RATE = 100kbps

RECESSIVE

DOMINANT

RECEIVER OUTPUT LOW vs.

OUTPUT CURRENT

MAX3051toc07

OUTPUT CURRENT (mA)

VOLTAGE RXD (V)

40355 10 15 2520 30

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

045

TA = -85°C

TA = +25°C

TA = -40°C

Typical Operating Characteristics

(VCC = +3.3V, RL= 60Ω, CL= 100pF, TA= +25°C, unless otherwise specified.)

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

_______________________________________________________________________________________ 7

RECEIVER PROPAGATION DELAY

MAX3051toc10

RXD

1v/div

CAHN - CANL

200ns/div

RS = GND

DRIVER PROPAGATION DELAY

MAX3051toc11

TXD

2V/div

RRS = 24kΩ

RRS = 75kΩ

RRS = 100kΩ

200ns/div

DRIVER PROPAGATION DELAY

MAX3051toc12

TXD

1V/div

CAHN - CANL

200ns/div

RS = GND

LOOPBACK PROPAGATION DELAY

vs. RRS

MAX3051toc13

RRS (kΩ)

LOOPBACK PROPAGATION DELAY (ns)

18016014012010080604020

200

400

600

800

1000

1200

0 200

Typical Operating Characteristics (continued)

(VCC = +3.3V, RL= 60Ω, CL= 100pF, TA= +25°C, unless otherwise specified.)

RECEIVER OUTPUT HIGH vs.

OUTPUT CURRENT

MAX3051toc08

OUTPUT CURRENT (mA)

RECEIVER OUTPUT HIGH (VCC - RXD) (V)

71 2 3 54 6

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1.8

DIFFERENTIAL VOLTAGE vs.

DIFFERENTIAL LOAD

MAX3051toc09

DIFFERENTIAL LOAD RL (Ω)

DIFFERENTIAL VOLTAGE (V)

200100

0.5

1.0

1.5

2.0

2.5

3.0

3.5

0300

TA = -85°C

TA = +25°C

TA = -40°C

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

8 _______________________________________________________________________________________

Detailed Description

PIN NAME FUNCTION

1 TXD Transmit Data Input. TXD is a CMOS/TTL-compatible input from a CAN controller. TXD has an

internal 75kΩ pullup resistor.

2 GND Ground

CC Supply Voltage. Bypass VCC to GND with a 0.1µF capacitor.

4 RXD Receive Data Output. RXD is a CMOS/TTL-compatible output.

5 SHDN Shutdown Input, CMOS/TTL-Compatible. Drive SHDN high to put the MAX3051 in shutdown.

SHDN has an internal 75kΩ pulldown resistor to GND.

6 CANL CAN Bus Line Low

7 CANH CAN Bus Line High

8RS

Mode-Select Input. Drive RS low or connect to GND for high-speed operation. Connect a resistor

between RS and GND to control output slope. Drive RS high to put into standby mode (see the

Mode Selection section).

MAX3051

0.75V

THERMAL

SHUTDOWN

TRANSMITTER

CONTROL

MODE

SELECTION

RECEIVER

VCC

RXD

GND

CANL

CANH

TXD

SHUTDOWN SHDN

VCC

Figure 5. MAX3051 Functional Diagram

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

_______________________________________________________________________________________ 9

Detailed Description

The MAX3051 interfaces between the CAN protocol

controller and the physical wires of the bus lines in a

CAN. It provides differential transmit capability to the

bus and differential receive capability to the CAN con-

troller. It is primarily intended for +3.3V single-supply

applications that do not require the stringent fault pro-

tection specified by the automotive industry (ISO 11898)

The MAX3051 features four different modes of opera-

tion: high-speed, slope-control, standby, and shutdown

mode. High-speed mode allows data rates up to

1Mbps. The slope-control mode can be used to pro-

gram the slew rate of the transmitter for data rates of up

to 500kbps. This reduces the effects of EMI, thus allow-

ing the use of unshielded twisted or parallel cable. In

standby mode, the transmitter is shut off and the

receiver is pulled high, placing the MAX3051 in low-

current mode. In shutdown mode, the transmitter and

receiver are switched off.

The MAX3051 input common-mode range is from -7V to

+12V, exceeding the ISO 11898 specification of -2V to

+7V. These features, and the programmable slew-rate

limiting, make the part ideal for nonautomotive, harsh

environments.

The transceivers operate from a single +3.3V supply

and draw 35µA of supply current in dominant state and

2µA in recessive state. In standby mode, supply cur-

rent is reduced to 8µA. In shutdown mode, supply cur-

rent is less than 1µA.

CANH and CANL are output short-circuit current limited

and are protected against excessive power dissipation

by thermal-shutdown circuitry that places the driver

outputs into a high-impedance state.

Transmitter

The transmitter converts a single-ended input (TXD)

from the CAN controller to differential outputs for the

bus lines (CANH, CANL). The truth table for the trans-

mitter and receiver is given in Table 1.

Receiver

The receiver reads differential inputs from the bus lines

(CANH, CANL) and transfers this data as a single-

ended output (RXD) to the CAN controller. It consists of

a comparator that senses the difference VDIFF = (CANH

- CANL) with respect to an internal threshold of +0.75V.

If this VDIFF is greater than 0.75, a logic-low is present at

RXD. If VDIFF is less than 0.75V, a logic-high is present.

The receiver always echoes the CAN BUS data.

The CANH and CANL common-mode range is -7V to

+12V. RXD is logic-high when CANH and CANL are

shorted or terminated and undriven.

Mode Selection

High-Speed Mode

Connect RS to ground to set the MAX3051 to high-

speed mode. When operating in high-speed mode, the

MAX3051 can achieve transmission rates of up to

1Mbps. In high-speed mode, use shielded twisted pair

cable to avoid EMI problems.

Slope-Control Mode

Connect a resistor from RS to ground to select slope-

control mode (Table 2). In slope-control mode, CANH

and CANL slew rates are controlled by the resistor con-

nected to the RS pin. Maximum transmission speeds

are controlled by RRS and range from 40kbps to

500kbps. Controlling the rise and fall slopes reduces

EMI and allows the use of an unshielded twisted pair or

a parallel pair of wires as bus lines. The equation for

selecting the resistor value is given by:

RRS (kΩ) ≈12000 / (maximum speed in kbps)

See the Slew Rate vs. RRS graph in the Typical

Operating Characteristics.

Standby Mode

If a logic-high is applied to RS, the MAX3051 enters a

low-current standby mode. In this mode, the transmitter

TXD RS SHDN CANH CANL BUS STATE RXD

Low VRS < 0.75 x

VCC Low High Low Dominant Low

High or float VRS < 0.75 x

VCC Low 5kΩ to 25kΩ to

VCC / 2

5kΩ to 25kΩ to

VCC / 2 Recessive High

XVRS > 0.75 x

VCC Low 5kΩ to 25kΩ to

GND

5kΩ to 25kΩ to

GND Recessive High

X X High Floating Floating Floating High

Table 1. Transmitter and Receiver Truth Table When Not Connected to the Bus

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

10 ______________________________________________________________________________________

is switched off and the receiver is switched to a low-

current/low-speed state. If dominant bits are detected,

RXD switches to low level. The microcontroller should

react to this condition by switching the transceiver back

to normal operation.

When the MAX3051 enters standby mode, RXD goes

high for 4µs (max) regardless of the BUS state.

However, after 4µs, RXD goes low only when the BUS

is dominant, otherwise RXD remains high (when the

BUS is recessive). For proper measurement of standby-

to-receiver active time (tSBRXDL), the BUS should be in

dominant state (see Figure 2).

Shutdown

Drive SHDN high to enter shutdown mode. Connect

SHDN to ground or leave floating for normal operation.

Thermal Shutdown

If the junction temperature exceeds +160°C, the device

is switched off. The hysteresis is approximately 25°C,

disabling thermal shutdown once the temperature

drops below 135°C. In thermal shutdown, CANH and

CANL go recessive and all IC functions are disabled.

Applications Information

Reduced EMI and Reflections

In slope-control mode, the CANH and CANL outputs

are slew-rate limited, minimizing EMI and reducing

reflections caused by improperly terminated cables.

In multidrop CAN applications, it is important to main-

tain a direct point-to-point wiring scheme. A single pair

of wires should connect each element of the CAN bus,

and the two ends of the bus should be terminated with

120Ωresistors (Figure 6). A star configuration should

never be used.

Any deviation from the point-to-point wiring scheme

creates a stub. The high-speed edge of the CAN data

on a stub can create reflections back down the bus.

These reflections can cause data errors by eroding the

noise margin of the system.

Although stubs are unavoidable in a multidrop system,

care should be taken to keep these stubs as small as

possible, especially in high-speed mode. In slope-con-

trol mode, the requirements are not as rigorous, but

stub length should still be minimized.

Power Supply and Bypassing

The MAX3051 requires no special layout considerations

beyond common practices. Bypass VCC to GND with a

0.1µF ceramic capacitor mounted close to the IC with

short lead lengths and wide trace widths.

CONDITION FORCED AT PIN RS MODE RESULTING CURRENT AT RS

VRS < 0.3 x VCC High Speed |IRS| < 500µA

0.4 x VCC <VRS < 0.6 x VCC Slope Control 10µA < |IRS| < 200µA

VRS > 0.75 x VCC Standby |IRS| < 10µA

Table 2. Mode Selection Truth Table

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

______________________________________________________________________________________ 11

Chip Information

TRANSISTOR COUNT: 1024

PROCESS: BiCMOS

MAX3051

CAN

CONTROLLER

TXD

VCC

RXD

RS GND

CANH

CANL

VCC

TX0

RX0

GND

0.1µF

120Ω

25kΩ TO 200kΩ

120Ω

Typical Operating Circuit

MAX3051

RL = 120Ω

RL = 120ΩTRANSCEIVER 3

TRANSCEIVER 1

TXD

RXD

CANH

CANL

TWISTED PAIR

STUB

LENGTH

KEEP AS SHORT

AS POSSIBLE

TRANSCEIVER 2

Figure 6. Multiple Receivers Connected to CAN Bus

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

12 ______________________________________________________________________________________

Package Information

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

go to www.maxim-ic.com/packages.)

SOICN .EPS

PACKAGE OUTLINE, .150" SOIC

21-0041 B

REV.DOCUMENT CONTROL NO.APPROVAL

PROPRIETARY INFORMATION

TITLE:

TOP VIEW

FRONT VIEW

MAX

0.010

0.069

0.019

0.157

0.010

INCHES

0.150

0.007

DIM

0.014

0.004

MIN

0.053A

0.19

3.80 4.00

0.25

MILLIMETERS

0.10

0.35

1.35

MIN

0.49

0.25

MAX

1.75

0.050

0.016L0.40 1.27

0.3940.386D

MINDIM

INCHES

MAX

9.80 10.00

MILLIMETERS

MIN MAX

16 AC

0.337 0.344 AB8.758.55 14

0.189 0.197 AA5.004.80 8

N MS012

SIDE VIEW

H 0.2440.228 5.80 6.20

e 0.050 BSC 1.27 BSC

eBA1

0∞-8∞

VARIATIONS:

MAX3051

+3.3V, 1Mbps, Low-Supply-Current

CAN Transceiver

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are

implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,

go to www.maxim-ic.com/packages.)

SOT23, 8L .EPS

REV.DOCUMENT CONTROL NO.APPROVAL

PROPRIETARY INFORMATION

TITLE:

3.002.60E

BETWEEN 0.08mm AND 0.15mm FROM LEAD TIP.

8. MEETS JEDEC MO178.

8∞

0.60

1.75

0.30

0∞

1.50E1

0.65 BSC.

1.95 REF.

0.25 BSC.

GAUGE PLANE

SEATING PLANE C

PIN 1

I.D. DOT

(SEE NOTE 6)

DETAIL "A"

5. COPLANARITY 4 MILS. MAX.

NOTE:

7. SOLDER THICKNESS MEASURED AT FLAT SECTION OF LEAD

6. PIN 1 I.D. DOT IS 0.3 MM ÿ MIN. LOCATED ABOVE PIN 1.

4. PACKAGE OUTLINE INCLUSIVE OF SOLDER PLATING.

3. PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH & METAL BURR.

HEEL OF THE LEAD PARALLEL TO SEATING PLANE C.

2. FOOT LENGTH MEASURED FROM LEAD TIP TO UPPER RADIUS OF

1. ALL DIMENSIONS ARE IN MILLIMETERS.

0.45

1.30

0.15

1.45

MAX

0.28b

0.90A2

0.00A1

0.90

MIN

SYMBOL

3.00

0.20

2.80D

0.09

SEE DETAIL "A"

21-0078

PACKAGE OUTLINE, SOT-23, 8L BODY