TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES * Improved dark sensitivity * Improved immunity against optical noise * Very low supply current * Photo detector and preamplifier in one package * Internal filter for PCM frequency * Low supply voltage: 2.0 V to 3.6 V 1 * Insensitive to supply voltage ripple and noise 2 3 * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 19026 DESIGN SUPPORT TOOLS click logo to get started MECHANICAL DATA Models 1 = OUT, 2 = GND, 3 = VS Available DESCRIPTION The TSOP98... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP982.. and TSOP984.. series devices are designed to receive long burst codes (10 or more carrier cycles per burst). The third digit designates the AGC level (AGC2 or AGC4) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC2 provides basic noise suppression and AGC4 provides enhanced noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE AGC 30 kHz Carrier frequency BASIC NOISE SUPPRESSION (AGC2) ENHANCED NOISE SUPPRESSION (AGC4) TSOP98230 TSOP98430 33 kHz TSOP98233 TSOP98433 36 kHz TSOP98236 TSOP98436 (6) 38 kHz TSOP98238 TSOP98438 (9) 40 kHz TSOP98240 (11) TSOP98440 56 kHz TSOP98256 (1) TSOP98456 (7)(8) Package Minicast Pinning 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 5.0 W x 6.95 H x 4.8 D Mounting Leaded Application Best choice for Remote control (1) Cisco (2) Mitsubishi (7) RCA (8) r-step (3) NEC (4) Panasonic (5) RC-5 (6) RC-6 (9) Sejin 4PPM (10) Sharp (11) Sony Notes * 30 kHz and 33 kHz only available on written request * See datasheet for TSOP986.. for preferred devices for (2)(3)(4)(5)(10) Rev. 1.2, 11-Dec-2018 1 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 17170-12 16833-13 R1 Transmitter with TSALxxxx 30 k IR receiver VS 1 Input Band pass AGC Demodulator + VS C1 Circuit 3 C OUT VO GND GND 2 PIN Control circuit R1 and C1 recommended to reduce supply ripple for VS < 2.2 V ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage VS -0.3 to +3.6 V Supply current IS 3 mA Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature Tj 100 C Tstg -25 to +85 C Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb -25 to +85 C Tamb 85 C Ptot 10 mW t 10 s, 1 mm from case Tsd 260 C Note * Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TYP. MAX. 0.25 0.37 0.45 mA - 0.50 - mA VS 2.0 - 3.6 V Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 24 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Test signal: NEC code Ee min. - 0.12 0.25 mW/m2 Maximum irradiance tpi - 4/f0 < tpo < tpi + 4/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 Angle of half transmission distance 1/2 - 45 - Supply current TEST CONDITION SYMBOL MIN. Ev = 0, VS = 3.3 V ISD Ev = 40 klx, sunlight ISH Supply voltage Transmission distance Directivity Rev. 1.2, 11-Dec-2018 2 UNIT Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) Axis Axis Title Title (1) T (1) AGC4: tpi 10/f0, AGC2: tpi 16/f0 VO VOH Output Signal (2) AGC4: 7/f0 < td < 13/f0 AGC2: 11/f0 < td < 17/f0 (3) 16110-10 tpi - 4/f0 < tpo < tpi + 4/f0 0.7 0.7 0.6 0.6 td (2) tpo (3) 1000 1000 0.5 0.5 ttoff off 0.4 0.4 0.3 0.3 100 100 0.2 0.2 0.1 0.1 0 0 VOL tton on 1st 1stline line 2nd 2ndline line 2nd 2ndline line ton ton, ,toff toff- -Output OutputPulse PulseWidth Width(ms) (ms) t tpi 10000 10000 0.8 0.8 Optical Test Signal (IR diode TSAL6200, 30 pulses, f = f0, T = 10 ms) Ee t = = 950 950 nm, nm, optical optical test test signal, signal, Fig. Fig. 3 3 0.1 0.1 1 1 10 10 10 100 1000 10 100 1000 10 10 000 000 100 100 000 000 2 E Eee -- Irradiance Irradiance (mW/m (mW/m2)) Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 1 - Output Delay and Pulse-Width Axis Title Axis Title 10000 0.90 10000 1.2 1000 0.75 1st line 2nd line 0.80 Input burst length 100 0.70 0.65 = 950 nm, optical test signal, Fig. 1 10 100 000 0.60 0.1 1000 1000 0.8 0.6 100 0.4 f = f0 5 % f (3 dB) = f0/10 0.2 10 0 0.7 0.9 1.1 1.3 Ee - Irradiance (mW/m2) f/f0 - Relative Frequency Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 5 - Frequency Dependence of Responsivity Axis Title Optical Test Signal 600 s 4 t 600 s t = 60 ms VO 1.0 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off 3 Wavelength of ambient illumination: = 950 nm 1000 2 100 1 0 0.01 t 10 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Test Signal Rev. 1.2, 11-Dec-2018 10000 Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 1st line 2nd line Ee 10 2nd line Ee min. - Threshold Irradiance (mW/m2) 2nd line tpo - Output Pulse Width (ms) 0.85 1st line 2nd line 2nd line Ee min./Ee - Relative Responsivity Output pulse width 3 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors Axis Title Axis Title f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 0.5 1000 0.4 100 0.3 0.2 0.1 0 1000 0.20 0.15 100 0.10 0.05 10 0 10 1 10 100 1000 VS RMS - AC Voltage on DC Supply Voltage (mV) -30 -10 10 Axis Title 1st line 2nd line TSOP982.. 0.4 100 TSOP984.. 0.2 0.1 10 20 40 60 80 100 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 1000 0.6 0.5 0.4 100 0.3 0.2 0.1 0 750 120 850 950 1050 10 1150 Burst Length (Number of Cycles/Burst) - Wavelength (nm) Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Axis0 Title 10 20 Axis0 Title 10 30 40 0.9 50 0.8 20 30 40 1.0 2nd line Vertical 1.0 2nd line 2nd line 2nd line Maximum Envelope Duty Cycle 0.7 0 2nd line Horizontal 2nd line S()rel. - Relative Spectral Sensitivity f = 38 kHz, Ee = 2 mW/m2 0 90 1.0 10000 0.3 70 Fig. 9 - Sensitivity vs. Ambient Temperature Axis Title 0.9 0.5 50 Tamb - Ambient Temperature (C) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances 0.8 30 0.9 50 0.8 60 60 70 0.7 70 0.7 80 0.6 0.4 0.2 0 0.2 0.4 2nd line 2nd line 0.6 0.25 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.8 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.9 0.7 10000 0.30 10000 1.0 80 0.6 0.6 drel. - Relative Transmission Distance 0.4 0.2 0 0.2 0.4 0.6 drel. - Relative Transmission Distance Fig. 11 - Horizontal and Vertical Directivity Rev. 1.2, 11-Dec-2018 4 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors Axis Title 10000 0.25 1000 0.20 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.30 0.15 100 0.10 0.05 10 0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 VS - Supply Voltage (V) Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.2, 11-Dec-2018 5 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device's band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 6 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver's output. 1000 1st line 2nd line 2nd line IR Signal Amplitude 5 4 3 100 2 1 Some examples which are suppressed are: 10 0 * DC light (e.g. from tungsten bulbs sunlight) 0 * Continuous signals at any frequency 5 10 15 20 Time (ms) 16920 * Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14) Fig. 13 - IR Disturbance from Fluorescent Lamp With Low Modulation Axis Title 10000 40 2nd line IR Signal Amplitude 20 1000 1st line 2nd line 0 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Disturbance from Fluorescent Lamp With High Modulation TSOP982.. TSOP984.. Minimum burst length 16 cycles/burst 10 cycles/burst After each burst of length a minimum gap time is required of 16 to 70 cycles 16 cycles 10 to 40 cycles 12 cycles For bursts greater than a minimum gap time in the data stream is needed of 70 cycles > 6 x burst length 40 cycles > 10 x burst length 1800 Maximum number of continuous short bursts/second 1000 RC-5 code Yes Yes RC-6 code Yes Preferred NEC code Yes Yes r-step code 56 kHz No Preferred Sony code RCA 56 kHz code Mitsubishi code 38 kHz Suppression of interference from fluorescent lamps Preferred No Yes Preferred Yes Yes Fig. 13 Fig. 13 and Fig. 14 Note * For data formats with short bursts please see the datasheet for TSOP983.., TSOP985.. Rev. 1.2, 11-Dec-2018 6 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP982.., TSOP984.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 5 4.8 (4) 2.8 (5.55) 6.95 0.3 8.25 0.3 R2 0.9 1.1 30.5 0.5 (1.54) 0.85 max. 0.7 max. 2.54 nom. 2.54 nom. 0.5 max. 1.2 0.2 Marking area technical drawings according to DIN specifications Not indicated to lerances 0.2 Drawing-No.: 6.550-5263.01-4 Issue: 12; 16.04.10 19009 Rev. 1.2, 11-Dec-2018 R2 7 Document Number: 82831 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2021 1 Document Number: 91000