Datasheet Serial EEPROM Series Standard EEPROM I2C BUS EEPROM (2-Wire) BR24Gxxx-3A (128K 256K 1M) General Description BR24Gxxx-3A is a serial EEPROM of I2C BUS Interface Method Features Packages W(Typ) x D(Typ)x H(Max) All controls available by 2 ports of serial clock(SCL) and serial data(SDA) Other devices than EEPROM can be connected to the same port, saving microcontroller port 1.7V to 5.5V Single Power Source Operation most suitable for battery use 1.7V to 5.5V wide limit of operating voltage, possible 1MHz operation Page Write Mode useful for initial value write at factory shipment Self-timed Programming Cycle Low Current Consumption Prevention of Write Mistake Write (Write Protect) Function added Prevention of Write Mistake at Low Voltage More than 1 million write cycles More than 40 years data retention Noise filter built in SCL / SDA terminal Initial delivery state FFh DIP-T8 TSSOP-B8 9.30mm x 6.50mm x 7.10mm 3.00mm x 6.40mm x 1.20mm SOP8 TSSOP-B8J 5.00mm x 6.20mm x 1.71mm 3.00mm x 4.90mm x 1.10mm SOP-J8 MSOP8 4.90mm x 6.00mm x 1.65mm 2.90mm x 4.00mm x 0.90mm SSOP-B8 VSON008X2030 3.00mm x 6.40mm x 1.35mm 2.00mm x 3.00mm x 0.60mm Figure 1. Page Write Number of Pages 64Byte 256Byte Product Number BR24G128-3A BR24G256-3A BR24G1M-3A BR24G128-3A Capacity Bit Format Type Power Source Voltage BR24G128-3A DIP-T8 BR24G128F-3A SOP8 BR24G128FJ-3A SOP-J8 BR24G128FV-3A 128kbit Package 16kx8 SSOP-B8 1.7V to 5.5V BR24G128FVT-3A TSSOP-B8 BR24G128FVJ-3A TSSOP-B8J BR24G128FVM-3A MSOP8 BR24G128NUX-3A VSON008X2030 Product structureSilicon monolithic integrated circuit This product has no designed protection against radioactive rays .www.rohm.com TSZ02201-0R2R0G100020-1-2 (c) 2014 ROHM Co., Ltd. All rights reserved. 1/36 18.Jun.2015 Rev.006 TSZ2211114001 BR24Gxxx-3A (128K 256K 1M) BR24G256-3A Capacity Bit Format 256kbit 32kx8 Type Power Source Voltage Package BR24G256-3A DIP-T8 BR24G256F-3A SOP8 BR24G256FJ-3A 1.7V to 5.5V SOP-J8 BR24G256FV-3A SSOP-B8 BR24G256FVT-3A TSSOP-B8 BR24G1M-3A Capacity Bit Format Type Power Source Voltage BR24G1M-3A 1Mbit 128kx8 BR24G1MF-3A DIP-T8 1.7V to 5.5V BR24G1MFJ-3A . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Package SOP8 SOP-J8 2/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Absolute Maximum Ratings (Ta=25C) Parameter Symbol Rating Unit Vcc -0.3 to +6.5 V Supply Voltage Power Dissipation 0.45 (SOP8) Derate by 4.5mW/C when operating above Ta=25C 0.45 (SOP-J8) Derate by 4.5mW/C when operating above Ta=25C 0.30 (SSOP-B8) Derate by 3.0mW/C when operating above Ta=25C 0.33 (TSSOP-B8) Pd Remark Derate by 3.3mW/C when operating above Ta=25C W 0.31 (TSSOP-B8J) Derate by 3.1mW/C when operating above Ta=25C 0.31 (MSOP8) Derate by 3.1mW/C when operating above Ta=25C 0.30 (VSON008X2030) Derate by 3.0mW/C when operating above Ta=25C 0.80 (DIP-T8) Derate by 8.0mW/C when operating above Ta=25C Storage Temperature Tstg -65 to +150 C Operating Temperature Topr -40 to +85 C -0.3 to Vcc+1.0 V The Max value of Input Voltage/Output Voltage is not over 6.5V. When the pulse width is 50ns or less, the Min value Input Voltage/Output Voltage is not lower than -1.0V. Tjmax 150 C Junction temperature at the storage condition VESD -4000 to +4000 V Input Voltage / Output Voltage Junction Temperature Electrostatic discharge voltage (human body model) Memory Cell Characteristics (Ta=25C, Vcc=1.7V to 5.5V) Parameter Min 1,000,000 40 Write Cycles (1) Data Retention (1) Limit Typ - Max - Unit Times Years (1) Not 100% TESTED Recommended Operating Ratings Parameter Power Source Voltage Input Voltage Symbol Vcc VIN Rating 1.7 to 5.5 0 to Vcc Unit V DC Characteristics (Unless otherwise specified, Ta=-40C to +85C, Vcc =1.7V to 5.5V) Parameter Symbol Limit Min Typ Max Unit Input High Voltage 1 VIH1 0.7Vcc - Vcc+1.0 V Input Low Voltage 1 VIL1 -0.3(2) - +0.3Vcc V Output Low Voltage 1 VOL1 - - 0.4 V Output Low Voltage 2 VOL2 - - 0.2 V Input Leakage Current ILI -1 - +1 A Output Leakage Current ILO -1 - +1 A - - 2.5 Supply Current (Write) Supply Current (Read) Standby Current ICC1 ICC2 mA - - 4.5 - - 2.0 - - 2.0 mA A ISB - - 3.0 Conditions IOL=3.0mA, 2.5VVcc5.5V (SDA) IOL=0.7mA, 1.7VVcc2.5V (SDA) VIN=0 to Vcc VOUT=0 to Vcc (SDA) VCC=5.5V, fSCL=1MHz, tWR=5ms, Byte write, Page write BR24G128/256-3A VCC=5.5V, fSCL=1MHz, tWR=5ms, Byte write, Page write BR24G1M-3A VCC=5.5V, fSCL=1MHz Random read, current read, sequential read VCC=5.5V, SDASCL=Vcc A0, A1, A2=GND, WP=GND BR24G128/256-3A VCC=5.5V, SDASCL=Vcc A0, A1, A2=GND, WP=GND BR24G1M-3A (2) When the pulse width is 50ns or less, it is -1.0V. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 3/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) AC Characteristics (Unless otherwise specified, Ta=-40C to +85C, Vcc=1.7V to 5.5V) Parameter Symbol Limit Min Typ Max Unit Clock Frequency fSCL - - 1000 kHz Data Clock "HIGH" Period tHIGH 0.30 - - s Data Clock "LOW" Period tLOW 0.5 - - s tR - - 0.12 s tF1 - - 0.12 s tF2 - - 0.12 s tHD:STA 0.25 - - s Start Condition Setup Time tSU:STA 0.20 - - s Input Data Hold Time tHD:DAT 0 - - ns Input Data Setup Time SDA, SCL (INPUT) Rise Time (1) SDA, SCL (INPUT) Fall Time (1) SDA (OUTPUT) Fall Time (1) Start Condition Hold Time tSU:DAT 50 - - ns Output Data Delay Time tPD 0.05 - 0.45 s Output Data Dold Time tDH 0.05 - - s Stop Condition Setup Time tSU:STO 0.25 - - s Bus Free Time tBUF 0.5 - - s Write Cycle Time tWR - - 5 ms tI - - 0.05 s tHD:WP 1.0 - - s WP Setup Time tSU:WP 0.1 - - s WP High Period tHIGH:WP 1.0 - - s Noise Spike Width (SDA, SCL) WP Hold Time (1) Not 100% tested AC Characteristics Condition Parameter Symbol Conditions Unit CL 100 pF SDA, SCL (INPUT) Rise Time tR 20 ns SDA, SCL (INPUT) Fall Time tF1 20 ns VIL1/VIH1 0.2VCC/0.8Vcc V - 0.3VCC/0.7Vcc V Load Capacitance Input Data Level Input/Output Data Timing Reference Level . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 4/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Serial Input / Output Timing tR SCL tF1 70% 70% 70% 70% 30% 30% tHD:DAT tSU:DAT 70% 70% 30% 30% tLOW tHD:STA 70% tHIGH 70% 70% 30% 30% SDA () (INPUT) tDH tPD tBUF 70% 70% SDA 30% () (OUTPUT) 30% 30% Input read at the rise edge of SCL Data output in sync with the fall of SCL tF2 Figure 2-(a). Serial Input / Output Timing 70% 70% 70% tSU:STA tHD:STA tSU:STO 70% 30% 30% STOP CONDITION START CONDITION Figure 2-(b). Start-Stop Bit Timing D0 70% 70% ACK write data (n-th address) tWR STOP CONDITION START CONDITION Figure 2-(c). Write Cycle Timing 70% DATA(n) DATA(1) D0 D1 70% ACK ACK tWR 30% 30% tSU:WP tHD:WP STOP CONDITION Figure 2-(d). WP Timing at Write Execution DATA(n) DATA(1) D1 D0 ACK ACK tWR tHIGH:WP 70% 70% 70% Figure 2-(e). WP Timing at Write Cancel . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 5/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Block Diagram (2) A0 1 128Kbit, 256Kbit, 1Mbit EEPROM Array 8 VCC 7 WP 6 SCL 5 SDA 8bit A1 (1)14biit Address Decoder 2 Word Address Register 15biit 17biit START A2 3 Data Register STOP Control Circuit ACK GND 4 High Voltage Generating Circuit (1) Power Source Voltage Detection 14bit: BR24G128-3A 15bit: BR24G256-3A 17bit: BR24G1M-3A (2) A0= Don't use : BR24G1M-3A Figure 3. Block Diagram Pin Configuration (TOP VIEW) A0 1 8 VCC A1 2 BR24G128-3A 1 BR24G256-3A BR24G1M-3A 3 7 4 5 SDA 1 A2 1 1 GND 1 1 WP 6 SCL 1 1 Pin Descriptions Descriptions Terminal Name Input/ Output A0 Input Slave address setting(2) A1 Input Slave address setting(2) A2 Input Slave address setting(2) GND - SDA Input/ Output SCL Input Serial clock input WP Input Write protect terminal VCC - BR24G128/256-3A BR24G1M-3A Don't use(1) Reference voltage of all input / output, 0V Serial data input serial data output Connect the power source. (1) Pins not used as device address may be set to any of `H', 'L', and 'Hi-Z'. (2) A0, A1 and A2 are not allowed to use as open . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 6/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curves 6 6 5 Ta=-40 Ta= 25 Input Low Voltage1 : VIL1(V) Input High Voltage1 : VIH1(V) 5 Ta= 85 4 3 SPEC 2 3 2 1 1 0 0 0 1 2 3 4 5 Ta=-40 Ta= 25 Ta= 85 4 SPEC 0 6 1 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 4. Input High Voltage1 vs Supply Voltage (A0, A1, A2, SCL, SDA, WP) Figure 5. Input Low Voltage1 vs Supply Voltage (A0, A1, A2, SCL, SDA, WP) 1 1 Ta=-40 Ta= 25 Ta= 85 0.8 Output Low Voltage2 : VOL2(V) Output Low Voltage1 : VOL1(V) 2 0.6 0.4 SPEC 0.2 Ta=-40 Ta= 25 Ta= 85 0.8 0.6 SPEC 0.4 0.2 0 0 0 1 2 3 4 5 0 6 2 3 4 5 6 Output Low Current : IOL(mA) Output Low Current : IOL(mA) Figure 7. Output Low Voltage2 vs Output Low Current (Vcc=1.7V) Figure 6. Output Low Voltage1 vs Output Low Current (Vcc=2.5V) . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 7/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 1.2 SPEC 1 Output Leakage Current : ILO(A) Input Leakage Current : I LI (A) 1.2 Ta=-40 Ta= 25 0.8 Ta= 85 0.6 0.4 0.2 0.8 Ta=-40 Ta= 25 0.6 Ta= 85 0.4 0.2 0 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage: Vcc(V) Figure 8. Input Leakage Current vs Supply Voltage (A0, A1, A2, SCL, WP) Figure 9. Output Leakage Current vs Supply Voltage (SDA) 6 3 SPEC 2.5 Supply Current (Write) : Icc1(mA) Supply Current (Write) : Icc1(mA) SPEC 1 Ta=-40 Ta= 25 Ta= 85 2 1.5 1 0.5 0 SPEC 5 4 Ta=-40 Ta= 25 Ta= 85 3 2 1 0 0 1 2 3 4 5 0 6 2 3 4 5 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 10. Supply Current (Write) vs Supply Voltage (fSCL=1MHz BR24G128/256-3A) . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 Figure 11. Supply Current (Write) vs Supply Voltage (fSCL=1MHz BR24G1M-3A) 8/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 6 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 2.5 2.5 SPEC 2 2 Standby Current : I SB (A) Supply Current (Read) : ICC2(mA) SPEC Ta=-40 Ta= 25 Ta= 85 1.5 1 0.5 Ta=-40 Ta= 25 Ta= 85 1.5 1 0.5 0 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 12. Supply Current (Read) vs Supply Voltage (fscl=1MHz) Figure 13. Standby Current vs Supply Voltage (BR24G128/256-3A) 10000 3.5 SPEC 2.5 Clock Frequency : fscl(kHz) Standby Current : I SB (A) 3 Ta=-40 Ta= 25 Ta= 85 2 1.5 1 1000 SPEC 100 Ta=-40 Ta= 25 Ta= 85 10 1 0.5 0 0.1 0 1 2 3 4 5 6 0 Supply Voltage : Vcc(V) 2 3 4 5 6 Supply Voltage : Vcc(V) Figure 14. Standby Current vs Supply Voltage (BR24G1M-3A) . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 1 Figure 15. Clock Frequency vs Supply Voltage 9/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 0.4 0.6 Data Clock Low Period : t LOW (s) Data Clock High Period : tHIGH(s) SPEC SPEC 0.3 Ta=-40 Ta= 25 Ta= 85 0.2 0.1 0 0.5 Ta=-40 Ta= 25 Ta= 85 0.4 0.3 0.2 0.1 0 0 1 2 3 4 5 0 6 1 Supply Voltage : Vcc(V) 3 4 5 6 Supply Voltage : Vcc(V) Figure 16. Data Clock High Period vs Supply Voltage Figure 17. Data Clock Low Period vs Supply Voltage 0.3 0.14 Start Condition Hold Time : tHD:STA(s) SPEC SDA (OUTPUT) Fall Time : tF 2(s) 2 0.12 0.1 Ta=-40 Ta= 25 Ta= 85 0.08 0.06 0.04 0.02 SPEC 0.25 0.2 Ta=-40 Ta= 25 Ta= 85 0.15 0.1 0.05 0 0 0 1 2 3 4 5 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure18. SDA (OUTPUT) Fall Time vs Supply Voltage . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 10/36 Figure 19. Start Condition Hold Time vs Supply Voltage TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 50 SPEC Input Data Hold Time : tHD:DAT (ns) Start Condition Setup Time : tSU:STA(s) 0.3 0.25 0.2 Ta=-40 Ta= 25 Ta= 85 0.15 0.1 0.05 SPEC 0 -50 Ta=-40 Ta= 25 Ta= 85 -100 -150 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 21. Input Data Hold Time vs Supply Voltage (HIGH) Figure 20. Start Condition Setup Time vs Supply Voltage 50 60 Input Data Setup Time : tSU:DAT(ns) Input Data Hold Time : tHD:DAT(ns) SPEC SPEC 0 -50 Ta=-40 Ta= 25 Ta= 85 -100 -150 50 Ta=-40 Ta= 25 Ta= 85 40 30 20 10 0 0 1 2 3 4 5 6 0 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 22. Input Data Hold Time vs Supply Voltage (LOW) Figure 23 Input Data Setup Time vs Supply Voltage (HIGH) . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 11/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 0.5 60 SPEC 50 Output Data Delay Time : tPD0(s) Input Data Setup Time : t SU:DAT(ns) SPEC 40 Ta=-40 Ta= 25 Ta= 85 30 20 10 0.4 0.3 0.2 Ta=-40 Ta= 25 Ta= 85 0.1 SPEC 0 0 0 1 2 3 4 5 0 6 1 2 6 0.3 SPEC Stop Condition Setup Time : t SU:STO(s) Output Data Delay Time : tPD1(s) 5 Figure 25. Output Data Delay Time vs Supply Voltage Figure 24. Input Data Setup Time vs Supply Voltage (LOW) 0.4 0.3 0.2 4 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) 0.5 3 Ta=-40 Ta= 25 Ta= 85 0.1 SPEC 0 SPEC 0.25 0.2 0.15 0.1 Ta=-40 Ta= 25 Ta= 85 0.05 0 0 1 2 3 4 5 6 Supply Voltage : Vcc(V) 1 2 3 4 5 6 Supply Voltage : Vcc(V) Figure 26. Output Data Delay Time vs Supply Voltage . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 12/36 Figure 27. Stop Condition Setup Time vs Supply Voltage TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 6 0.6 SPEC Write Cycle Time : tWR(ms) Bus Free Time : t BUF(s) SPEC 5 0.5 0.4 Ta=-40 Ta= 25 Ta= 85 0.3 0.2 4 3 2 0.1 1 0 0 0 1 2 3 4 5 6 Ta=-40 Ta= 25 Ta= 85 0 1 2 Supply Voltage : Vcc(v) 4 5 6 Supply Voltage : Vcc(v) Figure 29. Write Cycle Time vs Supply Voltage Figure 28. Bus Free Time vs Supply Voltage 0.3 0.3 Noise Spike Width(SCL LOW) : tI(s) Noise Spike Width(SCL HIGH) : tI(s) 3 0.25 Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC 0 0.25 Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC 0 0 1 2 3 4 5 6 Supply Voltage : Vcc(V) 1 2 3 4 5 6 Supply Voltage : Vcc(V) Figure 30. Noise Spike Width vs Supply Voltage (SCL HIGH) . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 13/36 Figure 31. Noise Spike Width vs Supply Voltage (SCL LOW) TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 0.3 Noise Spike Width(SDA LOW) : tI(s) Noise Spike Width(SDA HIGH) : tI(s) 0.3 0.25 Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC 0.25 Ta=-40 Ta= 25 Ta= 85 0.2 0.15 0.1 0.05 SPEC 0 0 0 1 2 3 4 5 0 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 33. Noise Spike Width vs Supply Voltage (SDA LOW) Figure 32. Noise Spike Width vs Supply Voltage (SDA HIGH) 1.2 0.2 SPEC SPEC WP Setup Time : t SU:WP(s) WP Hold Time : tHD:WP(s) 1 0.8 Ta=-40 Ta= 25 Ta= 85 0.6 0.4 0.2 0.1 Ta=-40 Ta= 25 Ta= 85 0 -0.1 -0.2 -0.3 0 0 1 2 3 4 5 6 1 2 3 4 5 6 Supply Voltage : Vcc(V) Supply Voltage : Vcc(V) Figure 35. WP Setup Time vs Supply Voltage Figure 34. WP Hold Time vs Supply Voltage . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 0 14/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Typical Performance Curvescontinued 1.2 WP High Period : tHIGH:WP ( s) SPEC 1 0.8 Ta=-40 Ta= 25 Ta= 85 0.6 0.4 0.2 0 0 1 2 3 4 5 6 Supply Voltage : Vcc(V) Figure 36. WP High Period vs Supply Voltage . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 15/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Timing Chart 1. I2C BUS Data Communication I2C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long, and acknowledge is always required after each byte. I2C BUS data communication with several devices is possible by connecting with 2 communication lines: serial data (SDA) and serial clock (SCL). Among the devices, there should be a "master" that generates clock and control communication start and end. The rest become "slave" which are controlled by an address peculiar to each device, like this EEPROM. The device that outputs data to the bus during data communication is called "transmitter", and the device that receives data is called "receiver".. SDA 1-7 SCL S START ADDRESS condition 1-7 8 9 R/W ACK 8 DATA 1-7 9 ACK 8 DATA 9 ACK Figure 37. Data Transfer Timing P STOP condition 2. Start Condition (Start Bit Recognition) (1) Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL is 'HIGH' is necessary. (2) This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this condition is satisfied, any command cannot be executed. 3. Stop Condition (Stop Bit Recognition) (1) Each command can be ended by a stop condition (stop bit) where SDA goes from 'LOW' to 'HIGH' while SCL is 'HIGH'. 4. Acknowledge (ACK) Signal (1) This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In master-slave communication, the device (Ex. -COM sends slave address input for write or read command to this IC) at the transmitter (sending) side releases the bus after output of 8bit data. (2) The device (Ex. This IC receives the slave address input for write or read command from the -COM) at the receiver (receiving) side sets SDA 'LOW' during 9th clock cycle, and outputs acknowledge signal (ACK signal) showing that it has received the 8bit data. (3) This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'. (4) After receiving 8bit data (word address and write data) during each write operation, this IC outputs acknowledge signal (ACK signal) 'LOW'. (5) During read operation, this IC outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'. When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (-COM) side, this IC continues to output data. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and recognizes stop condition (stop bit), and ends read operation. Then this IC becomes ready for another transmission. 5. Device Addressing (1) Slave address comes after start condition from master. (2) The significant 4 bits of slave address are used for recognizing a device type. The device code of this IC is fixed to '1010'. (3) Next slave addresses (A2 A1 A0 --- device address) are for selecting devices, and plural ones can be used on a same bus according to the number of device addresses. (4) The most insignificant bit (R/W --- READ/WRITE) of slave address is used for designating write or read action, and is as shown below. Setting R / W to 0 ------- write (setting 0 to word address setting of random read) Setting R / W to 1 ------- read Type BR24G128-3A, BR24G256-3A, BR24G1M-3A Maximum number of Connected buses Slave address 1 1 0 1 0 A2 A1 A0 R/W 0 1 0 A2 A1 P0 R/W 8 4 P0 is page select bit. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 16/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Write Command 1. Write Cycle (1) Arbitrary data can be written to EEPROM. When writing only 1 byte, Byte Write is normally used, and when writing continuous data of 2 bytes or more, simultaneous write is possible by Page Write cycle. The maximum number of write bytes is specified per device of each capacity. Up to 256 arbitrary bytes can be written.In the case of BR24G1M-3A S T A R T SDA LINE W R I T E SLAVE ADDRESS 1st WORD ADDRESS R A / C W K WA 0 (1) S T O P DATA WAWA 15 14 1 0 1 0 A2 A1 A0 Note) 2nd WORD ADDRESS A C K D7 (1) As for WA14, BR24G128-3A becomes don't care. As for WA15, BR24G128/256-3A becomes don't care. (1) As for WA14, BR24G128-3A becomes don't care. As for WA15, BR24G128/256-3A becomes don't care. (2) As for BR24G128/256-3A becomes (n+63) As for BR24G1M-3A becomes (n+255) D0 A C K A C K Figure 38. Byte Write Cycle S T A R T SDA LINE SLAVE ADDRESS 1 0 1 0 0 W R I T E A2 A1 A0 1st WORD ADDRESS(n) 2nd WORD ADDRESS(n) DATA(n) WA WA WA 15 14 0 D7 D0 D0 0 Note ) R A / C W K (1) A C K A C K S T O P (2) DATA(n+63) A C K A C K Figure 39. Page Write Cycle Note) (1) 1 0 1 0 A2A1A0 (1) In BR24G1M-3A A0 becomes P0. Figure 40. Difference of Slave Address of Each Type (2) During internal write execution, all input commands are ignored, therefore ACK is not returned. (3) Data is written to the address designated by word address (n-th address) (4) By issuing stop bit after 8bit data input, internal write to memory cell starts. (5) When internal write is started, command is not accepted for tWR (5ms at maximum). (6) Using page write cycle, writing in bulk is done as follows: Up to 64Byte (BR24G128-3A, BR24G256-3A Up to 256Byte (BR24G1M-3A The bytes in excess overwrite the data already sent first. (Refer to "Internal Address Increment") (7) As for page write cycle of BR24G128-3A and BR24G256-3A, where 2 or more bytes of data is intended to be written, after the 8 significant bits (BR24G128-3A) or 9 significant bits (BR24G256-3A) of word address are designated arbitrarily, only the value of 6 least significant bits in the address is incremented internally, so that data up to 64 bytes of memory only can be written. (8) As for page write cycle of BR24G1M-3A, where 2 or more bytes of data is intended to be written, after the page select bit `P0' of slave, and the 8 significant bits of word address are designated arbitrarily, only the value of 8 least significant bits in the address is incremented internally, so that data up to 256 bytes of memory only can be written . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 17/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) 2. Notes on Write Cycle Continuous Input List of numbers of page write Number of 64Byte 256Byte Pages Product BR24G128-3A BR24G1M-3A number BR24G256-3A The above numbers are maximum bytes for respective types. Any bytes below these can be written. In the case BR24G256-3A, 1 page=64bytes, but the page write cycle time is 5ms at maximum for 64byte bulk write. It does not stand 5ms at maximum x 64byte=320ms(Max) 3. Internal Address Increment Page write mode (in the case of BR24G128-3A 3Eh 0 0 0 WA7 WA6 WA5 WA4 WA3 WA2 WA1 WA0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 0 1 0 Increment For example, when it is started from address 3Eh, then, increment is made as below, 3Eh3Fh00h01h please take note. 3Eh3E in hexadecimal, therefore, 00111110 becomes a binary number. Significant bit is fixed. No digit up 4. Write Protect (WP) Terminal Write protect (WP) function When WP terminal is set at Vcc (H level), data rewrite of all addresses is prohibited. When it is set GND (L level), data rewrite of all address is enabled. Be sure to connect this terminal to Vcc or GND, or control it to H level or L level. Do not leave it open. In case of using it as ROM, it is recommended to connect it to pull up or Vcc. At extremely low voltage at power ON/OFF, by setting the WP terminal `H', write error can be prevented. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 18/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Read Command 1. Read Cycle Read cycle is when data of EEPROM is read. Read cycle could be random read cycle or current read cycle. Random read cycle is a command to read data by designating a specific address, and is used generally. Current read cycle is a command to read data of internal address register without designating an address, and is used when to verify just after write cycle. In both the read cycles, sequential read cycle is available where the next address data can be read in succession. S T A R T SDA LINE W R I T E SLAVE ADDRESS 2nd WORD ADDRESS R A / C W K A C K (1) R E A D SLAVE ADDRESS S T O P DATA(n) (1) WA 0 WAWA 15 14 1 0 1 0 A2A1A0 Note) 1st WORD ADDRESS S T A R T 1 0 1 0 A2 A1A0 A C K D7 D0 R A / C W K As for WA14, BR24G128-3A become don't care. As for WA15, BR24G128/256-3A become don't care. A C K Figure 41. Random Read Cycle S T A R T R E A D SLAVE ADDRESS SDA LINE S T O P DATA(n) 1 0 1 0 A2A1A0 D7 D0 A C K R A / C WK Note) Figure 42. Current Read Cycle S T A R T SDA LINE R E A D SLAVE ADDRESS 1 0 1 0 A2 A1A0 DATA(n) D7 D0 R A / C W K Note S T O P DATA(n+x) D7 A C K D0 A C K A C K Figure 43. Sequential Read Cycle (in the case of current read cycle) (1) In random read cycle, data of designated word address can be read. (2) When the command just before current read cycle is random read cycle, current read cycle (each including sequential read cycle), data of incremented last read address (n)-th, i.e., data of the (n+1)-th address is output. (3) When ACK signal 'LOW' after D0 is detected, and stop condition is not sent from master (-COM) side, the next address data can be read in succession. (4) Read cycle is ended by stop condition where 'H' is input to ACK signal after D0 and SDA signal goes from `L' to `H' while at SCL signal is `H'. (5) When 'H' is not input to ACK signal after D0, sequential read gets in, and the next data is output. Therefore, read command cycle cannot be ended. To end read command cycle, be sure to input 'H' to ACK signal after D0, and the stop condition where SDA goes from `L' to `H' while SCL signal is 'H'. (6) Sequential read is ended by stop condition where 'H' is input to ACK signal after arbitrary D0 and SDA is asserted from `L' to `H' while SCL signal is 'H'. Note) (1) A2 A1 A0 1 0 1 0 (1) In BR24G1M-3A, A0 becomes P0. Figure 44. Difference of Slave Address of Each Type . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 19/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Software Reset Software reset is executed to avoid malfunction after power ON, and during command input. Software reset has several kinds, and 3 kinds of them are shown in the figure below. (Refer to Figure 45-(a), Figure 45-(b), Figure 45-(c)) Within the dummy clock input area, the SDA bus is released ('H' by pull up) and ACK output and read data '0' (both 'L' level) may be output from EEPROM. Therefore, if 'H' is input forcibly, output may conflict and over current may flow, leading to instantaneous power failure of system power source or influence upon devices. Dummy clockx14 SCL 1 2 Startx2 13 Normal command 14 SDA Normal command Figure 45-(a). The Case of Dummy Clock x 14 +START+START+ Command Input SCL Start Dummy clockx9 Start 1 2 8 Normal command 9 SDA Normal command Figure 45-(b). The Case of START + Dummy Clock x 9 +START+ Command Input Startx9 SCL 1 2 3 7 8 Normal command 9 SDA Normal command SD Figure 45-(c). STARTx9+ Command Input Start command from START input. Acknowledge Polling During internal write execution, all input commands are ignored, therefore ACK is not returned. During internal automatic write execution after write cycle input, next command (slave address) is sent, and if the first ACK signal sends back 'L', then it means end of write operation, else 'H' is returned, which means writing is still in progress. By the use of acknowledge polling, next command can be executed without waiting for tWR = 5ms. To write continuously, R/W = 0, then to carry out current read cycle after write, slave address with R/W = 1 is sent, and if ACK signal sends back 'L', then execute word address input and data output and so forth. During internal write, ACK = HIGH is returned. First write command S T A R T Write command S T O P S T Slave A R address T A C K H tWR S T Slave A R address T A C K H ... Second write command ... S T Slave A R address T tWR A C K H S T Slave A R address T A C K L Word address A C K L Data A C K L S T O P After completion of internal write, ACK=LOW is returned, so input next word address and data in succession. Figure 46. Case to Continuous Write by Acknowledge Polling . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 20/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) WP Valid Timing (Write Cancel) WP is usually fixed to 'H' or 'L', but when WP is used to cancel write cycle and so on, pay attention to the following WP valid timing. During write cycle execution, inside cancel valid area, by setting WP='H', write cycle can be cancelled. In both byte write cycle and page write cycle, the area from the first start condition of command to the rise of clock to take in D0 of data(in page write cycle, the first byte data) is the cancel invalid area. WP input in this area becomes `Don't care'. The area from the rise of SCL to take in D0 to the stop condition input is the cancel valid area. Furthermore, after the execution of forced end by WP, the IC enters standby status.. Rise of SDA Rise of D0 taken clock SCL SDA SCL D1 D0 ACK SDA S T Slave A R address T A C Word K address L ACK Enlarged view Enlarged view SDA D0 A C D7 D6 D5 D4 D3 D2 D1 D0 K L WP cancel invalid area A C K L Data A C K L S T O P WP cancel valid area tWR WP cancel invalid area WP Data is not written. Figure 47. WP Valid Timing Command Cancel by Start Condition and Stop Condition During command input, by continuously inputting start condition and stop condition, command can be cancelled. (Figure 48.) However, within ACK output area and during data read, SDA bus may output 'L'. In this case, start condition and stop condition cannot be input, so reset is not available. Therefore, execute software reset. When command is cancelled by start-stop condition during random read cycle, sequential read cycle, or current read cycle, internal setting address is not determined. Therefore, it is not possible to carry out current read cycle in succession. To carry out read cycle in succession, carry out random read cycle. SCL SDA 1 0 1 0 Start condition Stop condition Figure 48. Case of Cancel by Start, Stop Condition during Slave Address Input . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 21/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) I/O Peripheral Circuit 1. Pull Up Resistance of SDA Terminal SDA is NMOS open drain, so it requires a pull up resistor. As for this resistor value (RPU), select an appropriate value from microcontroller VIL, IL, and VOL-IOL characteristics of this IC. If RPU is large, operating frequency is limited. The smaller the RPU, the larger is the supply current (Read). 2. Maximum Value of RPU The maximum value of RPU is determined by the following factors. (1)SDA rise time to be determined by the capacitance (CBUS) of bus line of RPU and SDA should be tR or lower. Furthermore, AC timing should be satisfied even when SDA rise time is late. (2)The bus electric potential A to be determined by input leak total (IL) of device connected to bus at output of 'H' to SDA bus and RPU should sufficiently secure the input 'H' level (VIH) of microcontroller and EEPROM including recommended noise margin of 0.2VCC. VCC-ILRPU-0.2 VCC VIH Ex.) VCC =3V From (2) RPU 0.8VCCVIH IL IL=10A VIH=0.7 VCC Microcontroller RPU BR24GXX RPU 0.8x30.7x3 10x10-6 IL 300 [k] 3. SDA terminal A IL Bus line capacity CBUS Figure 49. I/O Circuit Diagram Minimum Value of RPU The minimum value of RPU is determined by the following factors. (1) When IC outputs LOW, it should be satisfied that VOLMAX=0.4V and IOLMAX=3mA. VCCVOL IOL RPU RPU VCCVOL IOL (2) VOLMAX=0.4V should secure the input 'L' level (VIL) of microcontroller and EEPROM including recommended noise margin 0.1VCC. VOLMAX VIL-0.1 VCC Ex.) VCC =3V, VOL=0.4V, IOL=3mA, microcontroller, EEPROM VIL=0.3VCC from (1) RPU 30.4 3x10 -3 867 [] VOL=0.4 [V] VIL=0.3x3 =0.9 [V] Therefore, the condition (2) is satisfied. And 4. Pull Up Resistance of SCL Terminal When SCL control is made at the CMOS output port, there is no need for a pull up resistor. But when there is a time where SCL becomes 'Hi-Z', add a pull up resistor. As for the pull up resistor value, one of several k to several ten k is recommended in consideration of drive performance of output port of microcontroller. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 22/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Cautions on Microcontroller Connection 1. RS In I2C BUS, it is recommended that SDA port is of open drain input/output. However, when using CMOS input / output of tri state to SDA port, insert a series resistance RS between the pull up resistor RPU and the SDA terminal of EEPROM. This is to control over current that may occur when PMOS of the microcontroller and NMOS of EEPROM are turned ON simultaneously. RS also plays the role of protecting the SDA terminal against surge. Therefore, even when SDA port is open drain input/output, RS can be used. ACK SCL RPU RS SDA 'H' output of microcontroller 'L' output of EEPROM Microcontroller Over current flows to SDA line by 'H' output of microcontroller and 'L' output of EEPROM. EEPROM Figure 50. I/O Circuit Diagram 2. Figure 51. Input / Output Collision Timing Maximum Value of RS The maximum value of RS is determined by the following relations. (1) SDA rise time to be determined by the capacitance (CBUS) of bus line and RPU of SDA should be tR or lower. Furthermore, AC timing should be satisfied even when SDA rise time is slow. (2) The bus electric potential A to be determined by RPU and RS the moment when EEPROM outputs 'L' to SDA bus should sufficiently secure the input 'L' level (VIL) of microcontroller including recommended noise margin of 0.1VCC. (V CC VOL )xR S RPU +R S VCC RPU A RS VOL RS VOL +0.1V CC VIL + VILV OL 0.1V CC 1.1V CC -V IL x RPU IOL Ex. VCC =3V V IL=0.3V CC VOL =0.4V R PU =20k Bus line capacity CBUS VIL RS EEPROM Micro controller Figure 52. I/O Circuit Diagram 3. 0.3x3 0.4 0.1x3 1.1x3 0.3x3 x 20x10 3 1.67 [k] Minimum Value of RS The minimum value of RS is determined by over current at bus collision. When over current flows, noises in power source line and instantaneous power failure of power source may occur. When allowable over current is defined as I, the following relation must be satisfied. Determine the allowable current in consideration of the impedance of power source line in set and so forth. Set the over current to EEPROM to 10mA or lower. RPU VCC RS 'L'output RS RS I VCC I Over current I Ex.) Vcc=3V, I=10mA 'H' output RS Microcontroller 3 -3 10x10 EEPROM 300 [] Figure 53. I/O Circuit Diagram . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 23/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) I/O Equivalence Circuit 1. Input (A0, A1, A2, SCL, WP) 2. Input / Output (SDA) Figure 55. Input / Output Pin Circuit Diagram Figure 54. Input Pin Circuit Diagram Power-Up/Down Conditions At power on, the IC's internal circuits may go through unstable low voltage area as the Vcc rises, making the IC's internal logic circuit not completely reset, hence, malfunction may occur. To prevent this, the IC is equipped with POR circuit and LVCC circuit. To assure the operation, observe the following conditions at power ON. 1. Set SDA = 'H' and SCL ='L' or 'H' 2. Start power source so as to satisfy the recommended conditions of tR, tOFF, and Vbot for operating POR circuit. tR VCC Recommended conditions of tR, tOFF,Vbot tR tOFF Vbot 0 tOFF Vbot 10ms or below 10ms or larger 0.3V or below 100ms or below 10ms or larger 0.2V or below Figure 56. Rise Waveform Diagram 3. Set SDA and SCL so as not to become 'Hi-Z'. When the above conditions 1 and 2 cannot be observed, take the following countermeasures. (1) In the case when the above condition 1 cannot be observed such that SDA becomes 'L' at power ON. Control SCL and SDA as shown below, to make SCL and SDA, 'H' and 'H'. VCC tLOW SCL SDA After Vcc becomes stable After Vcc becomes stable tDH tSU:DAT Figure 57. When SCL= 'H' and SDA= 'L' tSU:DAT Figure 58. When SCL='L' and SDA='L' (2) In the case when the above condition 2 cannot be observed. After power source becomes stable, execute software reset(Page19). (3) In the case when the above conditions 1 and 2 cannot be observed. Carry out (1), and then carry out (2). Low Voltage Malfunction Prevention Function LVCC circuit prevents data rewrite operation at low power, and prevents write error. At LVCC voltage (Typ =1.2V) or below, data rewrite is prevented. Noise Countermeasures 1. Bypass Capacitor When noise or surge gets in the power source line, malfunction may occur, therefore, it is recommended to connect a bypass capacitor (0.1F) between the IC's VCC and GND pins. Connect the capacitor as close to IC as possible. In addition, it is also recommended to connect a bypass capacitor between board's VCC and GND. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 24/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Operational Notes 1. Described numeric values and data are design representative values only, and the values are not guaranteed. 2. We believe that the application circuit examples in this document are recommendable. However, in actual use, confirm characteristics further sufficiently. If changing the fixed number of external parts is desired, make your decision with sufficient margin in consideration of static characteristics, transient characteristics, and fluctuations of external parts and our LSI. 3. Absolute maximum ratings If the absolute maximum ratings such as supply voltage, operating temperature range, and so on are exceeded, LSI may be destroyed. Do not supply voltage or subject the IC to temperatures exceeding the absolute maximum ratings. In case of fear of exceeding the absolute maximum ratings, take physical safety countermeasures such as adding fuses, and see to it that conditions exceeding the absolute maximum ratings should not be supplied to the LSI. 4. GND electric potential Set the voltage of GND terminal lowest at any operating condition. Make sure that each terminal voltage is not lower than that of GND terminal. 5. Thermal design Use a thermal design that allows for a sufficient margin by taking into account the permissible power dissipation (Pd) in actual operating conditions. 6. Short between pins and mounting errors Be careful when mounting the IC on printed circuit boards. The IC may be damaged if it is mounted in a wrong orientation or if pins are shorted together. Short circuit may be caused by conductive particles caught between the pins. 7. Operating the IC in the presence of strong electromagnetic field may cause malfunction, therefore, evaluate design sufficiently. . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 25/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Part Numbering B R 2 4 G x x x x x x - 3 A x x x x BUS type 24I2C Operating temperature/ Operating Voltage -40C to +85C/ 1.7V to 5.5V Capacity 128=128K 256=256K 1M=1024K Package Blank : DIP-T8 F : SOP8 FV : SSOP-B8 FVJ : TSSOP-B8J NUX : VSON008X2030 : SOP-J8 FJ FVT : TSSOP-B8 FVM : MSOP8 Process Code Revision G : Halogen free Blank : Not Halogen free As an exception, VSON008X2030 package will be Halogen free with "Blank" T Blank : : 100% Sn 100% Sn Packaging and Forming Specification E2 : Embossed tape and reel (SOP8,SOP-J8, SSOP-B8,TSSOP-B8, TSSOP-B8J) TR : Embossed tape and reel (MSOP8, VSON008X2030) None : Tube (DIP-T8) Lineup Package Capacity Type DIP-T8 SOP8 SOP-J8 128K 1M Tube of 2000 Reel of 2500 Orderable Part Number BR24G128 Remark -3A Not Halogen free 100% Sn BR24G128F -3AGTE2 Halogen free 100% Sn BR24G128FJ -3AGTE2 Halogen free 100% Sn SSOP-B8 Reel of 2500 BR24G128FV -3AGTE2 Halogen free 100% Sn TSSOP-B8 Reel of 3000 BR24G128FVT -3AGE2 Halogen free 100% Sn TSSOP-B8J Reel of 2500 BR24G128FVJ -3AGTE2 Halogen free 100% Sn MSOP8 Reel of 3000 BR24G128FVM -3AGTTR Halogen free 100% Sn VSON008X2030 Reel of 4000 BR24G128NUX -3ATTR Halogen free 100% Sn DIP-T8 Tube of 2000 BR24G256 -3A Not Halogen free 100% Sn BR24G256F -3AGTE2 Halogen free 100% Sn SOP8 256K Quantity SOP-J8 Reel of 2500 BR24G256FJ -3AGTE2 Halogen free 100% Sn SSOP-B8 Reel of 2500 BR24G256FV -3AGTE2 Halogen free 100% Sn TSSOP-B8 Reel of 3000 BR24G256FVT -3AGE2 Halogen free 100% Sn DIP-T8 Tube of 2000 SOP8 SOP-J8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 Reel of 2500 BR24G1M -3A Not Halogen free 100% Sn BR24G1MF -3AGTE2 Halogen free 100% Sn BR24G1MFJ -3AGTE2 Halogen free 100% Sn 26/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Physical Dimensions Tape and Reel information DIP-T8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 27/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) SOP8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 28/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) SOP-J8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 29/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) SSOP-B8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 30/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) TSSOP-B8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 31/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) TSSOP-B8J . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 32/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) MSOP-8 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 33/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) VSON008X2030 . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 34/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Marking Diagrams SOP8(TOP VIEW) DIP-T8 (TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK SOP-J8(TOP VIEW) SSOP-B8(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK TSSOP-B8(TOP VIEW) TSSOP-B8J(TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK MSOP8(TOP VIEW) VSON008X2030 (TOP VIEW) Part Number Marking Part Number Marking LOT Number LOT Number 1PIN MARK 1PIN MARK . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 35/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 BR24Gxxx-3A (128K 256K 1M) Marking Information Product Name Marking Capacity BR24G128A Package DIP-T8 SOP8 4G12A SOP-J8 4GHA SSOP-B8 4G12A TSSOP-B8 128K 4G1 2A3 4GH A3 4G1 2A3 BR24G256A TSSOP-B8J MSOP8 VSON008X2030 DIP-T8 SOP8 4G25A 256K SOP-J8 4GJA SSSOP-B8 4G25A TSSOP-B8 BR24G1MA 1M DIP-T8 SOP8 4G1MA SOP-J8 Revision History Date Revision 12.Apr.2012 001 25.Feb.2013 002 31.May.2013 003 04.Jul.2013 004 02.May.2014 005 18.Jun.2015 006 Changes New Release Update some English words, sentences' descriptions, grammar and formatting. Update Part Numbering. Delete Lineup. P1 Change format of package line-up table. P.3 Add VESD in Absolute Maximum Ratings P.6 Add directions in Pin Descriptions P.4 Change Start Condition Setup Time from 0.25us to 0.20us. P.26 Update Part Numbering. Add Lineup table. P.17,24,26 Japanese datasheet updated P.3 Change unit of power dissipation from mW to W. P.24 Japanese datasheet updated . www.rohm.com (c) 2014 ROHM Co., Ltd. All rights reserved. TSZ2211115001 36/36 TSZ02201-0R2R0G100020-1-2 18.Jun.2015 Rev.006 Datasheet Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you (Note 1) , transport intend to use our Products in devices requiring extremely high reliability (such as medical equipment equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property ("Specific Applications"), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM's Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASS CLASSb CLASS CLASS CLASS CLASS 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM's Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual ambient temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label QR code printed on ROHM Products label is for ROHM's internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet General Precaution 1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents. ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny ROHM's Products against warning, caution or note contained in this document. 2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM's Products, please confirm the la test information with a ROHM sale s representative. 3. The information contained in this doc ument is provi ded on an "as is" basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. Notice - WE (c) 2015 ROHM Co., Ltd. All rights reserved. Rev.001 Datasheet br24g128f-3a - Web Page Buy Distribution Inventory Part Number Package Unit Quantity Minimum Package Quantity Packing Type Constitution Materials List RoHS br24g128f-3a SOP8 2500 2500 Taping inquiry Yes