Control Units
ø30 Series
ø30 Series Control Units (Selection Guide)
2
ø30
Function Emergency Stop Switch Pushbutton
Category Pushlock Turn Reset Flush Extended Extended with
Half Shroud Extended with
Full Shroud
Momentary/Maintained
Shape
Type HN1E ABN1
AON1
(Diecast)
ABD1
AOD1
ABN2
AON2
(Diecast)
ABD2
AOD2
ABN2G
AON2G
(Diecast)
ABGD2
AOGD2
ABN2F
AON2F
(Diecast)
ABFD2
AOFD2
Page 6 13 69136913691369
Function Pushbutton
Category Mushroom Mushroom with
Full Shroud Palm Mushroom Jumbo Mushroom with
Shallow Shroud Jumbo Mushroom with
Deep Shroud
Momentary/Maintained Momentary
Shape
Type ABN3
AON3
(Diecast)
ABD3
AOD3 ABN3G (Diecast)
ABGD3
AOGD3 ABN4 (Diecast)
ABD4 ABN4G (Diecast)
ABGD4 ABN4F (Diecast)
ABFD4
Page 14 70 14 70 14 70 14 70 14 70
Function Pushbutton
Category Square Flush Square Extended Mushroom Pushlock
Turn Reset Mushroom Pushlock
Key Reset Jumbo Mushroom
Pushlock Key Reset
Momentary Momentary
Shape
Type UBQN1 UBQN2 AVN3 (Diecast)
AVD3 ABN3K ABN4K
Page 14 14 15 71 15 15
Function Pushbutton
Category Mushroom Push
Turn Lock Key ON/OFF Lock Toggle Lever Mushroom Pull Mushroom Push-Pull
Shape
Type AJN3 (Diecast)
AJD3 ABN5 ATN4 ATN23 (Diecast)
AZD3 ATN21
ATN22 (Diecast)
AYD3
Page 15 71 15 15 16 71 16 71
ø30 Series Control Units (Selection Guide)
3
ø30
Function Pushbutton Twin Maintained Pushbutton
Category Pin Lock Square Twin Square Twin Flush Mushroom
Momentary Maintained
Shape
Type ABN8P (Diecast)
ABD8P UWQN1 UWQN2 ABBN11 ABBN33
Page 16 71 17 17 17 17
Function Pilot Light (LED) Pilot Light (Incandescent)
Category Dome Square Rectangular (Marking) Dome (1W) Dome (2W)
Shape
Type APN1
APNE1
(Diecast)
APD1
APDE1 UPQN3B UPQN4
UPQNE4 APN1 (Diecast)
APD1 APN1
APNE1
(Diecast)
APD1
APDE1
Page 18 72 19 19 19 72 18 72
Function Pilot Light (Incandescent) Illuminated Pushbutton (LED)
Category Rectangular (Marking)
(1W/2W) Square Flush (1W) Dome Extended Extended with
Half Shroud
Push-to-Check Momentary/Maintained
Shape
Type UPQN4
UPQNE4 UPQN3B APN1PALN2
ALNE2
AOLN2
AOLNE2
(Diecast)
ALD2
AOLD2
ALGN2
ALGNE2
AOLGN2
AOLGNE2
Page 19 19 21 22 73 24
Function Illuminated Pushbutton (LED) (Incandescent)
Category Extended with
Full Shroud Mushroom Mushroom Pushlock
Turn Reset Mushroom Push
Turn Lock Extended
Momentary/Maintained Momentary/Maintained
Shape
Type ALFN2
ALFNE2
AOLFN2
AOLFNE2
(Diecast)
ALFD2
AOLFD2
ALN3
ALNE3
AOLN3
AOLNE3
(Diecast)
ALD3
AOLD3
AVLN3
AVLNE3
(Diecast)
AVLD3
AVLDE3 AJLN3 ALN
ALNE
AOLN
AOLNE
(Diecast)
ALD2
AOLD2
Page 26 74 28 75 31 76 31 23 73
ø30 Series Control Units (Selection Guide)
4
ø30
Function Illuminated Pushbutton (Incandescent)
Category Extended with
Half Shroud Extended with
Full Shroud Square Flush Rectangular Turn Lock
Momentary Momentary/Maintained Momentary/Maintained
Shape
Type ALNG
ALNE3G3
ALNF
ALNE3F3
AOLNF
AOLNE3F3
(Diecast)
ALFD2
AOLFD2
ULQN
UOLQN ULQNB
UOLQNBALNL
Page 25 27 74 29 29 30
Function Illuminated Pushbutton (Incandescent) Selector Switch
Category Mushroom Pushlock
Turn Reset Mushroom Push
Turn Lock Knob Lever Key
Shape
Type AVLN3
AVLNE3
(Diecast)
AVLD3
AVLDE3 AJLN3 ASN
ASTN (Diecast)
ASD ASNL
ASTNL(Diecast)
ASDLASNK
ASTNK(Diecast)
ASDK
Page 32 76 32 33/37 77 34/38 78 35/39 79
Function Illuminated Selector
Switch (LED) Illuminated Selector
Switch (Incandescent) Selector Pushbutton Mono-Lever Switch
Category Knob Knob Ring Lever Standard
Shape
Type ASLN (Diecast)
ASLD ASLN (Diecast)
ASLD ABN (Diecast)
ASBD2 ABNL(Diecast)
ASBD2L ARN
ARNS
Page 40 80 40 80 42 82 42 82 44
Function Mono-Lever Switch Cam Switch
Category Interlocking Knob Key Maintained/
Spring Return Spring Return
Shape
Type ARNL ACSNO
ACSSO ACSNK
ACSSK UCSQO UCSQM
Page 44 47 47 47 47
5
HN Series Emergency Stop Switches
When pressed, the button is held depressed. The button is released by turning clockwise.
Terminal cover HW-VL7 is supplied with the switch.
When pressed, the button is held depressed. The button is released by turning clockwise.
The illuminated pushlock turn reset switch does not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
Terminal cover HW-VL7 is supplied with the switch.
Emergency Stop Switches (Unibody Type) Specifications
Pushlock Turn Reset Switches (Unibody Type)
Shape Contact Type No. Button Color
1NO-1NC HN1E-BV411R
Red only
2NC HN1E-BV402R
Illuminated Pushlock Turn Reset Switches (Unibody Type)
Shape Lamp Contact Type No. Lens Color
Without Lamp
1NO-1NC HN1E-LV411Q0R
Red only
2NC HN1E-LV402Q0R
Contact Ratings
Note: The operational current represents the classification by
making and breaking currents (IEC 60947-5-1).
Minimum applicable load (reference value): 3V AC/DC,
5 mA (Applicable range may vary with operating condi-
tions and load types.)
LED Lamp Ratings
Incandescent Lamp Ratings
Rated Insulation Voltage (Ui) 250V
Rated Thermal Current (Ith) 10A
Rated Operational Voltage (Ue) 24V 110V 220V
Rated
Operational
Current
AC
50/60
Hz
Resistive Load
(AC-12) 6A 3A 3A
Inductive Load
(AC-15) 6A 3A 3A
DC
Resistive Load
(DC-12) 6A 2A 1A
Inductive Load
(DC-13) 1.5A 0.3A 0.15A
Unit Rated
Operating
Voltage
LED Lamp
Type No. Rated Voltage Rated
Current
24V AC/DC LSTD-2R 24V AC/DC ±10% 10 mA
Unit Rated
Operating
Voltage
Incandescent Lamp
Type No. Wattage
24V AC/DC LS-3 1W (30V)
Specifications
Applicable Standards and Approvals
Operating
Temperature –25 to +60°C (no freezing)
Illuminated units: –25 to +55°C
Storage Temperature –40 to +80°C
Operating Humidity 45 to 85% RH (no condensation)
Contact Resistance 50 m maximum (initial value)
Insulation Resistance 100 M minimum (500V DC megger)
Dielectric Strength Between live and dead metal parts
Contacts: 2,500V AC, 1 minute
Illuminated parts: 1,000V AC, 1 minute
Vibration Resistance Damage limits: 60 m/s2
Operating extremes: 5 to 55 Hz,
amplitude 0.5 mm
Shock Resistance Damage limits: 1,000 m/s2
Operating extremes: 100 m/s2
Operating Frequency 900 operations/h
Life Mechanical: 250,000 operations minimum
Electrical: 100,000 operations minimum
Degree of Protection IP65
Terminal Style M3.5 screw
Safety Standards File No. or Organization
UL508 UL Listing File No. E55996
CSA C22.2 No. 14 c-UL (File No. E55996)
EN60947-5-5 DEMKO approved
ø30
HN Series Emergency Stop Switches
6
ø30
Dimensions
HN1E-BV4
HN1E-LV4
Replacement Parts
Nameplates
Accessory
Name Type No. Ordering Type No. Package Quantity Remarks
Terminal Cover HW-VL7 HW-VL7PN10 10 Used on HN1E emergency stop switches for preventing
electrical shocks.
The HW-VL7 terminal cover is supplied with the HN1E.
Shape Type No. Legend Package
Quantity Remarks
HNAV-0 (blank)
1
HNAV-27 EMERGENCY
STOP
Shape Material Type No. Package
Quantity Remarks
Metal TWST-T1 1
Used for tightening the locking nut.
Tighten the locking nut to a torque
of 2.0 to 2.5 N·m.
M3.5 Terminal
Screw Gasket
0.5
Terminal Arrangement
(Bottom View)
TOP Marking Side
Locking Ring
63
61 23.5
32
ø40
Panel Thickness 0.8 to 6
R0.8 max.
33
0
+0.2
4.8
0
+0.5
ø30.5
LAMP
X1
X2
0.5
63
61 23.5
32
M3.5 Terminal
Screw
M3.5 Terminal 
Screw
Gasket Panel Thickness 0.8 to 6
ø40
Locking Ring
Lamp Terminal
Terminal Arrangement
(Bottom View)
TOP Marking Side
All dimensions in mm.
1.0
1.5
ø60
ø30
Background: Yellow
Legend: Black
Applicable panel thickness:
0.8 to 4.5 mm
Material: Polyamide
Legend “EMERGENCY STOP”
is indicated outside a ø44mm
circle.
49.5
52
20.5
23.7 77
Panel Cut-Out
7
ø30 Series Control Units
Heavy duty control units offer both variety and reliability
Endures harsh environments
Degree of protection: IP65
UL, CSA approved, and EN compliant.
Contact Ratings
Characteristics
Contact Ratings by Utilization Category
Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1).
Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types)
For mono-levers and cam switches, see pages 43 and 46.
BS (BST) Contact Block
Durable nylon 66 housing has a high resistance against alkalis.
Silver contacts.
Up to four blocks in two layers can be mounted onto each operator.
Safety Standards File No. or Organization
UL UL Listing
File No. E68961
CSA File No. LR21451
EN EN60947-5-1
Specifications and Ratings
Pushbuttons
Illuminated Pushbuttons
Selector Switches
Illuminated Selector Switches
Selector Pushbuttons
Contact Block Type BS/BST (ø30 series)
Rated Insulation Voltage 600V
Rated Continuous Current 10A
Contact Ratings by Utilization Category
IEC 60947-5-1 AC-15 (A600)
DC-13 (P600)
Operational Voltage 24V 48V 50V 110V 220V 440V
Operational
Current
AC
50/60 Hz AC-12 Control of resistive loads and solid state loads 10A 10A 10A 6A 2A
AC-15 Control of electromagnetic loads (> 72 VA) 10A 7A 5A 3A 1A
DC DC-12 Control of resistive loads and solid state loads 10A 5A 2.2A 1.1A
DC-13 Control of electromagnets 5A 2A 1.1A 0.6A
Contact Block Types
Contact
Single-pole Contact Block Type
1NO 1NC 1NO (early make) 1NC (late break)
Type BS BS010E BS001E BS010SE BS001SE
BST BST010 BST001 BST010S BST001S
Push Rod Green Red Black White
BST contact blocks are used for the following control units and are not
interchangeable with BS contact blocks.
(The BS housing is dark gray and the BST housing is light gray.)
Pushlock turn reset and push turn lock switches
LED illuminated pushbuttons
LED/incandescent illuminated selector switches
All models of diecast zinc housing control units
Push Rod
M3.5 Terminal Screw
Inspection
Window
Interlocking
Groove
Mounting
Screw
ø30
ø30 Series Control Units
8
ø30
LED Illuminated Unit Specifications
Incandescent Illuminated Unit Specifications
LED Lamp Ratings (LSTD Type)
Unit Color Code Input Type Operating V oltage LED Lamp
Lamp Base Type No. Voltage
Pilot Light
Illuminated Pushbutton
Illuminated Selector Switch
A: amber
G: green
PW: pure white
R: red
S: blue
W: white
Y: yellow
Full V oltage
6V AC/DC BA9S/13 LSTD-66V AC/DC ±10%
12V AC/DC LSTD-112V AC/DC ±10%
24V AC/DC LSTD-224V AC/DC ±10%
6V AC/DC E12/15 LETD-66V AC/DC ±10%
12V AC/DC LETD-812V AC/DC ±10%
24V AC/DC LETD-224V AC/DC ±10%
Transformer
100/110V AC/DC
115V AC/DC
120V AC/DC
200/220V AC/DC
230V AC/DC
240V AC/DC
380V AC/DC
400/440V AC/DC
(50/60 Hz)
BA9S/13 LSTD-6
6V AC/DC ±10%
E12/15 LETD-6
DC-DC Converter 110V DC BA9S/13 LSTD-66V AC/DC ±10%
E12/15 LETD-6
Unit Color Code Input Type Operating V oltage Incandescent Lamp
Lamp Base Type No. Rating
Pilot Light
Illuminated Pushbutton
Illuminated Selector Switch
A: amber
G: green
O: orange
R: red
S: blue
W: white
Full V oltage
6V AC/DC BA9S/13 LS-6 1W (6.3V)
12V AC/DC LS-8 1W (18V)
24V AC/DC LS-3 1W (30V)
6V AC/DC E12/15 LE-6 2W (6.3V)
12V AC/DC LE-8 2W (18V)
24V AC/DC LE-3 12W (30V)
Transformer
100/110V AC/DC
115V AC/DC
120V AC/DC
200/220V AC/DC
230V AC/DC
240V AC/DC
380V AC/DC
400/440V AC/DC
480V AC/DC
(50/60 Hz)
BA9S/13 LS-6 1W (6.3V)
E12/15 LE-8 2W (18V)
Type No. LSTD-6LSTD-1LSTD-2
Lamp Base BA9S/13
Rated Voltage 6V AC/DC 12V AC/DC 24V AC/DC
Voltage Range 6V AC/DC ±10% 12V AC/DC ±10% 24V AC/DC ±10%
Current
Draw
AC A, R, W, Y: 17 mA
G, PW, S: 8 mA 11 mA 11 mA
DC A, R, W, Y: 14 mA
G, PW, S: 5.5 mA 10 mA 10 mA
Color Code A (amber), G (green), PW (pure white), R (red), S (blue), W (white), Y (yellow)
Lamp Base Color Same as illumination color
Voltage Marking Die stamped on the base
Life (reference value) Approx. 50,000 hours
(The luminance is reduced to 50% the initial intensity when used on complete DC.)
Internal Circuit
A, R, W, Y A, R, W, Y
G, PW, S
LED Chip
Protection Diode
Zener Diode
ø30 Series Control Units
9
ø30
LED Lamp Ratings (LETD Type)
Incandescent Lamp Ratings (LS Type)
Incandescent Lamp Ratings (LE Type)
Type No. LETD-6LETD-8LETD-2
Lamp Base E12/15
Rated Voltage 6V AC/DC 12V AC/DC 24V AC/DC
Voltage Range 6V AC/DC ±10% 12V AC/DC ±10% 24V AC/DC ±10%
Current
Draw
AC A, R, W, Y: 17 mA
G, S: 8 mA 7 mA 11 mA
DC A, R, W, Y: 14 mA
G, S: 5.5 mA 6.5 mA 10 mA
Color Code A (amber), G (green), R (red), S (blue), W (white), Y (yellow)
Lamp Base Color Same as illumination color
Voltage Marking Die stamped on the base
Life (reference value) Approx. 50,000 hours
(The luminance is reduced to 50% the initial intensity when used on complete DC.)
Internal Circuit
A, R, W, Y A, R, W, Y
G, S
Type No. LS-6 LS-8 LS-2 LS-3
Lamp Base BA9S/13
Rated Voltage 6V AC/DC 12V AC/DC 18V AC/DC 24V AC/DC
Wattage 1W (6.3V) 1W (18V) 1W (24V) 1W (30V)
Voltage Marking Die stamped on the base
Life (reference value) Approx. 1,000 hours minimum
(mean value when used on the rated voltage)
Type No. LE-6 LE-8 LE-2 LE-3
Lamp Base E12/15
Rated Voltage 6V AC/DC 12V AC/DC 18V AC/DC 24V AC/DC
Wattage 2W (6.3V) 2W (18V) 2W (24V) 2W (30V)
Voltage Marking Die stamped on the base
Life (reference value) Approx. 1,000 hours minimum
(mean value when used on the rated voltage)
LED Chip
Protection Diode
Zener Diode
ø30 Series Control Units
10
ø30
Specifications
Degree of Protection
Note: (3S) of NEMA ICS 6-110 applies to the pilot lights with round lens.
Note: For mounting hole layout of pushbuttons, mono-lever switches, and cam switches, see each section.
Operating Temperature –25 to +50°C (no freezing)
Operating Humidity 45 to 85% RH (no condensation)
Contact Resistance 50 m maximum (initial value)
Insulation Resistance 100 M minimum (500V DC megger)
Dielectric Strength Between live and dead metal parts: 2,500V AC, 1 minute
(Full voltage type and pilot lights: 2,000V AC, 1 minute)
Vibration Resistance Operating extremes: 5 to 55 Hz, amplitude 0.5 mm
Shock Resistance Damage limits: 1,000 m/s2
Operating extremes: 100 m/s2
Mechanical Life
(minimum operations)
Pushbuttons
Momentary: 5,000,000
Maintained: 500,000
Illuminated pushbuttons
Momentary: 2,500,000
Maintained: 500,000
Selector switches: 500,000
Key selector switches: 500,000
Illuminated selector switches: 500,000
Selector pushbuttons: 250,000
Mono-lever switches: 500,000
(Interlocking type): 250,000
Pushlock turn reset 500,000
Mushroom push-pull switch
Two contact blocks: 500,000
Four contact blocks: 200,000
Electrical Life
(minimum operations)
Pushbuttons: 500,000 1
Illuminated pushbuttons: 500,000 1
Selector switches: 500,000 2
Key selector switches: 500,000 2
Illuminated selector switches: 500,000 2
Selector pushbuttons: 250,000 2
Mono-lever switches: 500,000 3
(Interlocking type): 250,000 3
1 Switching frequency 1,800 operations/h, duty ratio 40% 4
2 Switching frequency 1,200 operations/h, duty ratio 40%
3 Switching frequency 900 operations/h, duty ratio 40%
4 Switching frequency 900 operations/h for square twin or twin
maintained types
Type No. Unit NEMA ICS 6-110 IEC 60529
A∗∗∗∗
Pushbuttons , pilot lights, illuminated pushbuttons , selector switches, selector
pushbuttons, mono-lever switches, and cam switches (ACSNO/ACSSO) Type 1, 2, 3, 3R, (3S), 4, 5, 12,13 IP65
Illuminated selector switches, key pushbuttons, key reset pushbuttons, key
cam switches, and key selector switches Type 1, 2, 3, 3R, 5, 12, 13 IP54
U∗∗∗∗ Square pushbuttons, square pilot lights, and cam switches (UC) Type 1, 2 IP40
Mounting Hole Layout
The minimum mounting centers are applicable to switches with
one layer of contact blocks (two contact b loc ks). When tw o layers
of contact blocks (four contact blocks) are mounted, determine
the minimum mounting centers in consideration of convenience
for wiring.
Mushroom with shroud: 50 mm minimum
Jumbo mushroom: 67 mm minimum
Jumbo mushroom with shroud: 76 mm minimum
Square twin: 55 mm minimum
Selector switch with lever: 50 mm minimum
The 4.8 mm recess is for preventing rotation and is not neces-
sary when the nameplate or anti-rotation ring is not used.
R0.8 max.
Square Unit: 55
0
+0.5
0
+0.5
+0.2
0
50
Round Unit: 42
33
ø30.5
4.8
R0.8 max.
0
0
+0.5
0
+0.5
+0.2
50
ø30.5
33
4.8
(Twin Maintained Type)
ø30 Series Control Units (Ordering Information)
11
ø30
Ordering Information
Standard Units
Specify an operator or lens color code in the Type No.
Black, g reen, and red buttons are included with flush push-
buttons.
Full voltage type illuminated units are not supplied with a
lamp. Order LED or incandescent lamps separately.
Transformer and DC-DC converter type illuminated units
contain an LED or incandescent lamp.
Terminal cov ers, nameplates, and accessories are ordered
separately.
Terminal Cover
When a terminal cover is required, order an applicable
terminal cover referring to page 55.
The Type No. development charts shown below can be used to specify control units other than those listed on the following
pages. Gold-plated silver contacts are also available.
ø30 Series Pushbuttons
ø30 Series Pilot Lights
ø30 Series Illuminated Pushbuttons
ABN2 11 R - MAU Optional contact
MAU: Gold-plated silver contact
Button color code
Contact arrangement code
10: 1NO 01: 1NC
11: 1NO-1NC 20: 2NO
02: 2NC 21: 2NO-1NC
12: 1NO-2NC 30: 3NO
03: 3NC 31: 3NO-1NC
22: 2NO-2NC 13: 1NO-3NC
40: 4NO 04: 4NC
Note:
Mushroom pull type ATN23 can have a maximum of two contact
blocks.
Mushroom push-pull return type ATN22 cannot have only NO or
only NC contacts.
No other contact configurations are av ailable f or square twin type
UWQN1 than those specified in this catalog.
APN1 116 D R
Note:
Full voltage type is not supplied with a lamp.
Transformer and DC-DC converter types contain an LED lamp
(LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8,
2W).
LED lamps cannot be used on 480V AC transformers.
DC-DC converter is available with LED lamps only.
Operating v oltage codes 18, 118, 128, 28, 238, 248, 388, 48, and
488 are available for incandescent types only.
Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Operating voltage code
99: Full voltage
16/18: Transformer (100/110V AC)
116/118: Transformer (115V AC)
126/128: Transformer (120V AC)
26/28: Transformer (200/220V AC)
236/238: Transformer (230V AC)
246/248: Transformer (240V AC)
386/388: Transformer (380V AC)
46/48: Transformer (400/440V AC)
486/488: Transformer (480V AC)
16D: DC-DC converter (110V DC)
ALFN2 116 13 D N R - MAU
Note:
Illuminated pushbuttons cannot have an odd number of contact
blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and 3NC.
Transformer and DC-DC converter types contain an LED lamp
(LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8,
2W).
LED lamps cannot be used on 480V AC transformers.
DC-DC converter is available with LED lamps only.
Operating v oltage codes 18, 118, 128, 28, 238, 248, 388, 48, and
488 are available for incandescent types only.
Optional contact
MAU: Gold-plated silver contact
Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Contact arrangement code
11: 1NO-1NC 20: 2NO
02: 2NC 31: 3NO-1NC
22: 2NO-2NC 13: 1NO-3NC
40: 4NO 04: 4NC
Operating voltage code
99: Full voltage
16/18: Transformer (100/110V AC)
116/118: Transformer (115V AC)
126/128: Transformer (120V AC)
26/28: Transformer (200/220V AC)
236/238: Transformer (230V AC)
246/248: Transformer (240V AC)
386/388: Transformer (380V AC)
46/48: Transformer (400/440V AC)
486/488: Transformer (480V AC)
16D: DC-DC conv erter (110V DC)
ø30 Series Control Units (Ordering Information)
12
ø30
ø30 Series Selector Switch
ø30 Series Key Selector Switch
ø30 Series Illuminated Selector Switch
ASN 2 L 11 - MAU Optional contact
MAU: Gold-plated silver contact
Contact arrangement code
Operator type
(blank): Knob
L: Lever
Number of positions
ASN 2 K 20 B - MAU Optional contact
MAU: Gold-plated silver contact
Key removable position code
2-position
Maintained
(blank): Removable in all positions
B: Removable in left only
C: Removable in right only
Spring return from right
(blank): Removable in left only
Spring return from left
(blank): Removable in right only
3-position
Maintained
(blank): Removable in all positions
B: Removable in left and center
C: Removable in right and center
D: Removable in center only
E: Removable in right and left
G: Removable in left only
H: Removable in right only
Spring return from right
(blank): Removable in left and center
D: Removable in center only
G: Removable in left only
Spring return from left
(blank): Removable in right and center
D: Removable in center only
H: Removable in right only
Spring return two-way
(blank): Removable in center only
Contact arrangement code
Number of positions
Note:
The key cannot be removed in the return position.
ASLN 2 16 22 D N R - MAU
Optional contact
MAU: Gold-plated silver contact
Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Contact arrangement code
Operating voltage code
99: Full voltage
16: Transformer (100/110V AC)
156: Transformer (115V AC)
136: Transformer (120V AC)
26: Transformer (200/220V AC)
236: Transformer (230V AC)
256: Transformer (240V AC)
386: Transformer (380V AC)
46: Transformer (400/440V AC)
486: Transformer (480V AC)
Number of positions
Note:
Full voltage type is not supplied with a lamp.
Transformer type contain an LED lamp (LSTD-6) or incandes-
cent lamp (LS-6, 1W).
LED lamps cannot be used on 480VAC transformers.
ø30 Series Pushbuttons
13
ø30
Round bezel and shroud (metal): Chrome-plated
Other contact arrangements and gold-plated silver contacts are also available. See page 11.
Flush / Extended / Extended w/Half Shroud / Extended w/Full Shroud Types
Shape Operation
Type Contact Type No. Button Color
Code Dimensions (mm)
Momentary
1NO ABN110
Black (B), green
(G), and red (R)
buttons are sup-
plied with each
unit.
Specify Y or W
when a yello w or
white button is
required.
1NC ABN101
1NO-1NC ABN111
2NO ABN120
2NC ABN102
2NO-2NC ABN122
Maintained
1NO AON110
1NC AON101
1NO-1NC AON111
2NO AON120
2NC AON102
2NO-2NC AON122
Momentary
1NO ABN210
Specify a button
color code in
place of in the
Type No.
B: black
G: green
R: red
W: white
Y: yellow
1NC ABN201
1NO-1NC ABN211
2NO ABN220
2NC ABN202
2NO-2NC ABN222
Maintained
1NO AON210
1NC AON201
1NO-1NC AON211
2NO AON220
2NC AON202
2NO-2NC AON222
Extended with Half Shroud
Momentary
1NO ABN2G10
1NC ABN2G01
1NO-1NC ABN2G11
2NO ABN2G20
2NC ABN2G02
2NO-2NC ABN2G22
Extended with Half Shroud
Maintained
1NO AON2G10
1NC AON2G01
1NO-1NC AON2G11
2NO AON2G20
2NC AON2G02
2NO-2NC AON2G22
Extended with Full Shroud
ABN2F
Momentary
1NO ABN2F10
1NC ABN2F01
1NO-1NC ABN2F11
2NO ABN2F20
2NC ABN2F02
2NO-2NC ABN2F22
Extended with Full Shroud
Maintained
1NO AON2F10
1NC AON2F01
1NO-1NC AON2F11
2NO AON2F20
2NC AON2F02
2NO-2NC AON2F22
Flush
ABN1 M3.5 Terminal Screw
623
46 (1 or
2 blocks)
69 (3 or 4 blocks)9
Panel Thickness 0.8 to 7.5
ø35
36
40
Flush
AON1
M3.5 Terminal Screw
623
9
Panel Thickness 0.8 to 7.5
ø35
36
40
68 (1 to 2 blocks)
91 (3 to 4 blocks)
Extended
ABN2
M3.5 Terminal Screw
623
46 (1 or
2 blocks)
69 (3 or 4 blocks)
9
Panel Thickness 0.8 to 7.5
ø35
36
40
ø25
15.5
Extended
AON2
M3.5 Terminal Screw
623
9
Panel Thickness 0.8 to 7.5
ø35
36
40
ø25
15.5
68 (1 to 2 blocks)
91 (3 to 4 blocks)
ABN2G
M3.5 Terminal Screw
623
ø35
40
ø25
Panel Thickness 0.8 to 4
20.5
ø27
42 (1 or
2 blocks)
65 (3 or 4 blocks)
36
AON2G
M3.5 Terminal Screw
623
ø35
40
ø25
Panel Thickness 0.8 to 4
20.5
ø27
36
64 (1 or 2 blocks)
87 (3 or 4 blocks)
M3.5 Terminal Screw
623
ø35
40
ø25
Panel Thickness 0.8 to 7.5
46 (1 or
2 blocks)
69 (3 or 4 blocks)17
ø28.5
36
AON2F
M3.5 Terminal Screw
623
ø35
40
ø25
Panel Thickness 0.8 to 7.5
17
ø28.5
36
68 (1 or 2 blocks)
91 (3 or 4 blocks)
ø30 Series Pushbuttons
14
ø30
Specify a button color code in place of in the Type No.
Round bezel and shroud (metal): Chrome-plated
Other contact arrangements and gold-plated silver contacts are also available. See page 11.
Mushroom / Jumbo Mushroom / Square Flush / Square Extended Types
Shape Operation
Type Contact Type No. Button Color
Code Dimensions (mm)
Momentary
1NO ABN310
B: black
G: green
R: red
W: white
Y: yellow
1NC ABN301
1NO-1NC ABN311
2NO ABN320
2NC ABN302
2NO-2NC ABN322
Maintained
1NO AON310
1NC AON301
1NO-1NC AON311
2NO AON320
2NC AON302
2NO-2NC AON322
Momentary
1NO ABN3G10
1NC ABN3G01
1NO-1NC ABN3G11
2NO ABN3G20
2NC ABN3G02
2NO-2NC ABN3G22
Momentary
1NO ABN410
B: black
G: green
R: red
1NC ABN401
1NO-1NC ABN411
2NO ABN420
2NC ABN402
2NO-2NC ABN422
Momentary
1NO ABN4G10
1NC ABN4G01
1NO-1NC ABN4G11
2NO ABN4G20
2NC ABN4G02
2NO-2NC ABN4G22
Momentary
1NO ABN4F10
1NC ABN4F01
1NO-1NC ABN4F11
2NO ABN4F20
2NC ABN4F02
2NO-2NC ABN4F22
Momentary
1NO UBQN110
B: black
G: green
R: red
Y: yellow
1NC UBQN101
1NO-1NC UBQN111
2NO UBQN120
2NC UBQN102
2NO-2NC UBQN122
Momentary
1NO UBQN210
1NC UBQN201
1NO-1NC UBQN211
2NO UBQN220
2NC UBQN202
2NO-2NC UBQN222
Mushroom
ABN3
M3.5 Terminal Screw
623 40
Panel Thickness 0.8 to 7.5
46 (1 or
2 blocks)
69 (3 or 4 blocks)
36
21
ø40
Mushroom
AON3 M3.5 Terminal Screw
623 40
Panel Thickness 0.8 to 7.5
36
68 (1 or 2 blocks)
91 (3 or 4 blocks)21
ø40
Mushroom with Full Shroud
ABN3G M3.5 Terminal Screw
623
Panel Thickness 0.8 to 6.5
44 (1 or
2 blocks)
67 (3 or 4 blocks)23
ø48
Palm Mushroom
ABN4 M3.5 Terminal Screw
623
46 (1 or
2 blocks)
69 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
35
ø74
Jum
b
o Mus
h
room wit
h
Shallow Shroud
ABN4G
M3.5 Terminal Screw
623
Panel Thickness 0.8 to 7.5
ø75
46 (1 or
2 blocks)
69 (3 or 4 blocks)
ø65
28
Jumbo Mushroom with Deep
Shroud
ABN4F
M3.5 Terminal Screw
623
Panel Thickness 0.8 to 7.5
32.5
ø75
46 (1 or
2 blocks)
69 (3 or 4 blocks)
Square Flush
UBQN1 M3.5 Terminal Screw
623
40
Panel Thickness 0.8 to 5.5
36
14
34
44
52.2
70.5 (3 or 4 blocks)
47.5 (1 or
2 blocks)
Square Extended
UBQN2 M3.5 Terminal Screw
623
40
Panel Thickness 0.8 to 5.5
36
34
44
47.5 (1 or
2 blocks)
52.2
70.5 (3 or 4 blocks)20
ø30 Series Pushbuttons
15
ø30
Specify a button color code in place of in the Type No.
Round bezel (metal): Chrome-plated
Cylinder (metal): Chrome-plated
Other contact arrangements and gold-plated silver contacts are also available. See page 11.
Pushlock T urn Reset: Button is maintained when pressed and is reset when turned clockwise. Red buttons only.
Note: A VN3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the
HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant).
Pushlock Key Reset: Button is maintained when pressed and is reset with a key. Key is removable from both depressed and reset posi-
tions. Two keys are supplied.
Push T urn Lock: Button is locked when turned clockwise in the depressed position and is reset when turned counterclockwise.
Key ON/OFF Lock: Button can be locked in both depressed and reset positions.
Toggle Lever: ON and OFF are indicated on the cap.
Pushlock Turn Reset / Pushlock Key Reset / Push Turn Lock /
Key ON/OFF Lock / Toggle Lever Types
Shape Contact Type No. Button Color
Code Dimensions (mm)
1NO AVN310N
R: red
Y: yellow
1NC AVN301N
1NO-1NC AVN311N
2NO AVN320N
2NC AVN302N
2NO-2NC AVN322N
1NO ABN3K10
B: black
G: green
R: red
Y: yellow
1NC ABN3K01
1NO-1NC ABN3K11
2NO ABN3K20
2NC ABN3K02
2NO-2NC ABN3K22
1NO ABN4K10
B: black
G: green
R: red
1NC ABN4K01
1NO-1NC ABN4K11
2NO ABN4K20
2NC ABN4K02
2NO-2NC ABN4K22
1NO AJN310N
B: black
G: green
R: red
Y: yellow
1NC AJN301N
1NO-1NC AJN311N
2NO AJN320N
2NC AJN302N
2NO-2NC AJN322N
1NO ABN510
1NC ABN501
1NO-1NC ABN511
2NO ABN520
2NC ABN502
2NO-2NC ABN522
1NO ATN410
Lever: black
1NC ATN401
1NO-1NC ATN411
2NO ATN420
2NC ATN402
2NO-2NC ATN422
Mushroom Pushlock Turn Reset
AVN3 M3.5 Terminal Screw
40
53 (1 or
2 blocks)
76 (3 or 4 blocks)
ø40
Panel Thickness 0.8 to 7.5
24
36
5.5 23
Mushroom Pushlock Key Reset
ABN3K M3.5 Terminal Screw
FREE
623 40
53 (1 or 2
blocks)
76 (3 or 4 blocks)
ø40
Panel Thickness 0.8 to 7.5
24 23.5
36
Jumbo Mushroom
ABN4K
Pushlock Key Reset M3.5 Terminal Screw
FREE
623
53 (1 or 2
blocks)
76 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
ø65
23 23.5
Mushroom Push Turn Lock
AJN3 M3.5 Terminal Screw
K
P
U
S
H
L
O
C
40
53 (1 or 2
blocks)
76 (3 or 4 blocks)
ø40
Panel Thickness 0.8 to 7.5
24
36
5.5 23
Key ON/OFF Lock
ABN5 M3.5 Terminal Screw LOCK
623
Panel Thickness 0.8 to 7.5
23 23.5
54 (1 or 2
blocks)
77 (3 or 4 blocks)
ø25
ø35
40
36
90°
Toggle Lever
ATN4 M3.5 Terminal Screw
40
Panel Thickness 0.8 to 5.5
36
623
44 (1 or
2 blocks)25
67 (3 or 4 blocks)
ø35
ø30 Series Pushbuttons
16
ø30
Specify a button color code in place of in the Type No.
Round bezel and shroud (metal): Chrome-plated
Square bezel (metal): Chrome-plated
Other contact arrangements and gold-plated silver contacts are also available. See page 11.
Pull: Pulling the button operates the contacts. Up to 2 contact blocks (1 layer) can be mounted on pull switches.
Push-Pull: Button is maintained in both depressed and reset positions.
Push-Pull (Spring Return): Pushing or pulling the button operates the contacts. Button is spring-returned to the center position.
Pin Lock: Button can be loc ked in either depressed or reset position b y inserting the pin. Pad lock with a ø6mm pin can also be used to lock
the button.
Pin Lock (ON Lock Type): Button is locked in the depressed position by inserting the pin. Button cannot be locked in the reset position.
Pull / Push-Pull / Pin Lock Types
Shape Contact Type No. Button Color
Code Dimensions (mm)
1NO ATN2310
B: black
G: green
R: red
Y: yellow
1NO-1NC ATN2311
2NO ATN2320
2NC ATN2302
1NO-1NC ATN2111
2NO ATN2120
2NC ATN2102
2NO-2NC ATN2122
1NO-1NC ATN2211
2NO-2N
CATN2222
1NO ABN8P10
1NC ABN8P01
1NO-1NC ABN8P11
2NO ABN8P20
2NC ABN8P02
2NO-2NC ABN8P22
1NO ABN8P10-TK231-1
1NC ABN8P01-TK231-1
1NO-1NC ABN8P11-TK231-1
2NO ABN8P20-TK231-1
2NC ABN8P02-TK231-1
2NO-2NC ABN8P22-TK231-1
Mushroom Pull
ATN23 M3.5 Terminal Screw
40
53 (1 or 2 blocks)
ø40
Panel Thickness 0.8 to 7.5
36
623
38.5
Mushroom Push-Pull
ATN21 M3.5 Terminal Screw
40
53 (1 or 2
blocks)
ø40
Panel Thickness 0.8 to 7.5
36
623
38.5
76 (3 or 4 blocks)
Mushroom Push-Pull
ATN22
(Spring Return) M3.5 Terminal Screw
40
53 (1 or 2
blocks)
ø40
Panel Thickness 0.8 to 7.5
36
623
38.5
76 (3 or 4 blocks)
Pin Lock
ABN8P M3.5 Terminal Screw
40
49
36
51
23
Panel Thickness 0.8 to 7.5
44.5 (1 or
2 blocks)
6
67 (3 or 4 blocks)26.5
ø28
ø35
Pin Lock (ON Lock Type)
ABN8P∗∗
-TK231-1
M3.5 Terminal Screw
40
49
36
51
23
Panel Thickness 0.8 to 7.5
44 (1 or 2
blocks)
6
67 (3 or 4 blocks)25.4
ø28
ø35
M3.5 Terminal Screw
40
49
36
51
23
Panel Thickness 0.8 to 7.5
44 (1 or 2
blocks)
6
67 (3 or 4 blocks)25.4
ø28
ø35
Pull Switch (Spring Return)
Contact ATN23
Normal Pull
1NO
1NC
1NO-1NC
2NO
2NC
Push-Pull Switch (Maintained)
Contact ATN21
Push Pull
1NO-1NC
2NO
2NC
2NO-2NC
Push-Pull (Spring Return) Switch
Contact ATN22
Push Normal Pull
1NO-1NC
2NO-2NC
Contact Operation
ø30 Series Pushbuttons
17
ø30
Round bezel (metal): Chrome-plated
Other contact arrangements and gold-plated silver contacts are also available. See page 11.
Square Twin (Momentary): Two independent momentary s witches are contained in one unit, each operated by ON or OFF button. With the
ø30 adapter removed form the sleeve, the unit can mount in a ø25.5mm mounting hole for the ø25 series.
Square Twin (Maintained): The contact operates when ON button is pressed and is maintained in the depressed position. The button is
reset by pressing the OFF button.
Twin Maintained: The contact operates when the top button is pressed and is maintained in the depressed position. The button is reset by
pressing the bottom button.
Different combinations of flush, extended buttons, and colors are available (ABN1B-, ABN2B-∗). See page 61.
Mushroom buttons for the ABBN33 are ordered separately. Specify the color code (ABN3B-∗). See page 61.
Square Twin / Twin Maintained Types
Shape Contact Type No. Button Color Dimensions (mm)
Square Twin (Momentary)
UWQN1 ON OFF
ON: Black
OFF: Red
1NO 1NO UWQN11010
1NO 1NC UWQN11001
2NO 2NC UWQN12002
Square Twin (Maintained)
UWQN2 ON OFF
ON: Black
OFF: Red
1NO UWQN21000
1NC UWQN20100
1NO-1NC UWQN21100
2NO UWQN22000
2NC UWQN20200
Flush Twin Maintained
ABBN11 TopBottom
Black (B), green
(G), and red (R)
buttons are sup-
plied with each
unit.
Other color buttons
are separately
ordered.
See page 61.
1NO ABBN1110
1NC ABBN1101
1NO-1NC ABBN1111
2NO ABBN1120
2NC ABBN1102
2NO-2NC ABBN1122
Mushroom Twin Maintained
(Without buttons)
ABBN33
TopBottom
Order buttons sep-
arately.
See page 61.
1NO ABBN3310
1NC ABBN3301
1NO-1NC ABBN3311
2NO ABBN3320
2NC ABBN3302
2NO-2NC ABBN3322
O N
OFF
M3.5 Terminal Screw
623
Panel Thickness 0.8 to 13
47 (1 or
2 blocks)
70 (3 or 4 blocks)15.5
53
42
36
O N
OFF
M3.5 Terminal Screw
623
Panel Thickness 0.8 to 13
47 (1 block)
70 (2 blocks) 15.5 53
42
36
0.8 to 7.5
M3.5 Terminal Screw
Panel
Thickness
57
80 40
ø35
50
86
9
M3.5 Terminal Screw
Panel
Thickness
0.8 to 7.5
57
80 40
50
86
ø40
21
ø30 Series Pilot Lights
18
ø30
Operating V oltage Code
Specify an operating voltage code in place of in the Type No.
Specify a lens/LED color code in place of in the Type No. Use the white lens (W) for LED pure white illumination.
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC).
∗∗ Pure white is available for BA9S lamp base types only.
Dimensions
Dome Types
Shape Lamp Input T ype Lamp
Receptacle Type No. Lens/LED
Color Code Applicable
Lamp
Dome
APN1
APNE1 Without Lamp Full Voltage
BA9S APN199A: amber
C: clear
G: green
O: orange
R: red
S: blue
W: white
Y: yellow
LSTD
LS (1W)
E12 APNE199LETD
LE (2W)
LED
Transformer BA9S APN1DNA: amber
G: green
PW: pure white∗∗
R: red
S: blue
W: white
Y: yellow
LSTD-6
E12 APNE1DNLETD-6
DC-DC ConverterBA9S APN116DDNLSTD-6
E12 APNE116DDNLETD-6
Incandescent Transformer
BA9S APN1➂➁ C: clear
G: green
O: orange
R: red
S: blue
W: white
LS-6 (1W)
E12 APN1➂➁ LE-8 (2W)
Operating V oltage Code
LED Transformer BA9S and E12 Types
Incandescent T ransformer BA9S Type Incandescent T ransformer E12 T ype
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
M3 Terminal Screw
40
ø35
Panel Thickness 0.8 to 7.5
21.5 23.5
36
M3.5 Terminal Screw
40
ø35
Panel Thickness 0.8 to 7.5
23.5
36
58.5
All dimensions in mm.
Full Voltage Type
Transformer Type
DC-DC Converter Type
ø30 Series Pilot Lights
19
ø30
Square / Rectangular (Marking) Types
Shape Lamp Input T ype Lamp
Receptacle Type No. Lens/LED
Color Code Applicable
Lamp
Square
UPQN3B
Without Lamp Full Voltage BA9S UPQN3B99
A: amber
C: clear
G: green
O: orange
R: red
S: blue
W: white
Y: yellow
LSTD
LS (1W)
LED
Transformer BA9S UPQN3BDA: amber
G: green
R: red
S: blue
W: white
Y: yellow
LSTD-6
DC-DC ConverterBA9S UPQN3B16DDLSTD-6
Incandescent Transformer BA9S UPQN3B➂➁
C: clear
G: green
O: orange
R: red
S: blue
W: white
LS-6 (1W)
Rectangular (Marking Type)
UPQN4
Without Lamp Full Voltage BA9S UPQN499
A: amber
G: green
O: orange
R: red
S: blue
W: white
Y: yellow
LSTD
LS (1W)
LED
Transformer BA9S UPQN4DA: amber
G: green
R: red
S: blue
W: white
Y: yellow
LSTD-6
DC-DC ConverterBA9S UPQN416DDLSTD-6
Incandescent Transformer BA9S UPQN4➂➁
G: green
O: orange
R: red
S: blue
W: white
LS-6 (1W)
Rectangular (Marking Type)
UPQNE4
UPQN4 Without Lamp Full Voltage E12 UPQNE499
A: amber
G: green
O: orange
R: red
S: blue
W: white
Y: yellow
LETD
LE (2W)
LED
Transformer E12 UPQNE4DA: amber
G: green
R: red
S: blue
W: white
Y: yellow
LETD-6
DC-DC ConverterE12 UPQNE416DDLETD-6
Incandescent Transformer E12 UPQN4➂➁
G: green
O: orange
R: red
S: blue
W: white
LE-8 (2W)
ø30 Series Pilot Lights
20
ø30
Operating V oltage Code
Specify an operating voltage code in place of in the Type No.
Specify a lens/LED color code in place of in the Type No.
On the rectangular marking type, a clear lens and a color marking plate are used for white illumination.
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Marking plate for the rectangular marking type: 24 × 30 mm, 2 mm thick
DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC).
Dimensions
Operating V oltage Code
LED Transformer BA9S and E12 Types
Incandescent T ransformer BA9S Type Incandescent T ransformer E12 T ype
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
M3 Terminal
Screw
40
36
34
Panel Thickness 0.8 to 5.5
23 20
52.2
44
M3 Terminal
Screw
40
36
Panel Thickness 0.8 to 4.5
52.2
44
29.5 10.5
34 × 40
M3 Terminal
Screw
40
36
Panel Thickness 0.8 to 4.5
52.2
10.5
34 × 40
36.5
M3.5 Terminal
Screw
40
36
34
Panel Thickness 0.8 to 5.5
20
52.2
44
25
60
M3.5 Terminal
Screw
40
36
Panel Thickness 0.8 to 4.5
52.2
44
10.5
34 × 40
66
30 × 36
M3.5 Terminal
Screw
40
36
Panel Thickness 0.8 to 4.5
52.2
10.5
34 × 40
30 × 36
74
Square Full Voltage Type
UPQN3B Rectangular Full Voltage Type
UPQN4 Rectangular Full Voltage Type
UPQNE4
Square T ransformer Type
Square DC-DC Converter Type
UPQN3B
Rectangular T ransformer Type
Rectangular DC-DC Converter Type
UPQN4
Rectangular T ransformer Type
Rectangular DC-DC Converter Type
UPQNE4
All dimensions in mm.
Reflector
1. The lamp housing of the square type LED illuminated
pilot lights has a built-in reflector.
2. Make sure that the reflector does not fall off when
removing the lens or marking plate.
3. When replacing the LED lamp of UPQNE4 (rectangular)
type, use a lamp holder tool (OR-55).
4. To remove the reflector, insert a flat screwdriver inside
the groove of the reflector and lightly push out.
Panel Mounting
1. Tighten the square ring to the operator and position the
ring correctly.
2. Lightly tighten the scre w to secure the pilot light onto the
panel.
Groove Tighten the screw
lightly so that the panel
does not bend.
Screw
Recommended
tightening torque: 0.15 N·m
ø30 Series Pilot Lights
21
ø30
Operating V oltage Code
Specify an operating voltage code in place of in the Type No.
Specify a lens color code in place of in the Type No.
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC).
Circuit Example
Dimensions
Incandescent Push-to-Check Types (1W)
Shape Lamp Input T ype Lamp
Receptacle Type No. Lens/LED
Color Code Applicable
Lamp
Push-to-Check
APN1PWithout Lamp Full Voltage BA9S APN199PC: clear
G: green
O: orange
R: red
S: blue
W: white
LS (1W)
Incandescent Transformer BA9S APN1PLS-6 (1W)
Operating V oltage Code
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC
M
L
STOP START OLS
Push-to-Check
Pilot Light
M
Note: The lamp of push-to-check pilot light is not connected to the contact terminal.
To connect, refer to the diagram on the left.
M3 Lamp Terminal Screw
M3.5 Terminal Screw M3.5 Terminal
Screw
40
ø35
36
623
B: 96.5 23.5
A: 62.5
Panel Thickness 0.8 to 7.5
All dimensions in mm.
Push-to-Check
APN1
P
A: Full voltage type
B: Transf ormer type
ø30 Series Illuminated Pushbuttons
22
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Dimensions
LED Round Extended Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
Round Extended
ALN2
AOLN2
ALNE2
AOLNE2
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALN29911DNLSTD2NO ALN29920DN
2NC ALN29902DN
LED Transformer 1NO-1NC ALN211DNLSTD-62NO ALN220DN
2NC ALN202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLN29911DNLSTD2NO AOLN29920DN
2NC AOLN29902DN
LED Transformer 1NO-1NC AOLN211DNLSTD-62NO AOLN220DN
2NC AOLN202DN
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALNE29911DNLETD2NO ALNE29920DN
2NC ALNE29902DN
LED Transformer 1NO-1NC ALNE211DNLETD-62NO ALNE220DN
2NC ALNE202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLNE29911DNLETD2NO AOLNE29920DN
2NC AOLNE29902DN
LED Transformer 1NO-1NC AOLNE211DNLETD-62NO AOLNE220DN
2NC AOLNE202DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED Transformer BA9S and E12 Types
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
PW: pure white (BA9S type only)
R: red
S: blue
W: white
Y: yellow
Use the white lens (W) for LED pure white illumination.
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
86 (4 blocks)
63 (2 blocks) 9
23.5
Panel Thickness 0.8 to 7.5
5.5 23
ø35
ø24
M3 Terminal
Screw M3.5 Terminal
Screw
ø40
40
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
9
23
Panel Thickness 0.8 to 7.5
ø24
ø35
23.5
ø40
40
100.5 (4 blocks)
77.5 (2 blocks) 920
Panel Thickness 0.8 to 7.5
5.5 23
ø35
ø24
M3 Terminal
Screw M3.5 Terminal
Screw
ø40
40
M3.5 Terminal
Screws
112 (2 blocks)
135 (4 blocks)
9
23
Panel Thickness 0.8 to 7.5
ø24
ø35
ø40
40
20
ALN2/AOLN2
BA9S/Full V oltage ALN2/AOLN2
BA9S/Transformer
ALNE2/AOLNE2
E12/Full V oltage ALNE2/AOLNE2
E12/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
23
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Dimensions
Incandescent Round Extended Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact T ype No. Applicable
Lamp
Round Extended
ALN
ALNE
AOLN
AOLNE
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALN9911LS (1W)2NO ALN9920
2NC ALN9902
Incandescent Transformer 1NO-1NC ALN11LS-62NO ALN20
2NC ALN02
Maintained
Without Lamp Full Voltage 1NO-1NC AOLN9911LS (1W)2NO AOLN9920
2NC AOLN9902
Incandescent Transformer 1NO-1NC AOLN11LS-62NO AOLN20
2NC AOLN02
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALNE9911LE (2W)2NO ALNE9920
2NC ALNE9902
Incandescent Transformer 1NO-1NC ALN11LE-82NO ALN20
2NC ALN02
Maintained
Without Lamp Full Voltage 1NO-1NC AOLNE9911LE (2W)2NO AOLNE9920
2NC AOLNE9902
Incandescent Transformer 1NO-1NC AOLN11LE-82NO AOLN20
2NC AOLN02
Lens Color Code Operating V oltage Code
Incandescent Illuminated Type Incandescent T ransformer BA9S Type Incandescent Transformer E12 Type
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
C: clear
G: green
O: orange
R: red
S: blue
W: white
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
M3 Terminal
Screw
M3.5 Terminal
Screw
92.5 (4 blocks)
69.5 (2 blocks) 18.5
Panel Thickness
0.8 to 7.5
623
ø35
ø24.6
M3.5 Terminal
Screws
103.5 (2 blocks)
126.5 (4 blocks)
23
Panel Thickness
0.8 to 7.5
ø24.6
ø35
18.5 114.5 (4 blocks)
91.5 (2 blocks) 18.5
Panel Thickness
0.8 to 7.5
623
ø35
ø24.6
M3 Terminal
Screw
M3.5 Terminal
Screw M3.5 Terminal Screws
125.5 (2 blocks)
148.5 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø24.6
ø35
36
40
18.5
85.5 (4 blocks)
62.5 (2 blocks) 18.5
623
ø35
ø24.6
Panel Thickness
0.8 to 7.5
M3 Terminal
Screw
M3.5 Terminal
Screw
107.5 (4 blocks)
84.5 (2 blocks) 18.5
Panel Thickness
0.8 to 7.5
623
ø35
ø24.6
M3 Terminal
Screw
M3.5 Terminal
Screw M3.5 Terminal
Screws
118.5 (2 blocks)
141.5 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø24.6
ø35
36
40
18.5
M3.5 Terminal
Screws
96.5 (2 blocks)
119.5 (4 blocks)
23
Panel Thickness
0.8 to 7.5
ø24.6
ø35
18.5
ALN Momentary
BA9S/Full V oltage ALN Momentary
BA9S/Transformer AOLN Maintained
BA9S/Full V oltage AOLN Maintained
BA9S/Transformer
ALNE Momentary
E12/Full V oltage ALNE Momentary
E12/Transformer AOLNE Maintained
E12/Full V oltage AOLNE Maintained
E12/Transformer
ø30 Series Illuminated Pushbuttons
24
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Dimensions
LED Round Extended with Half Shroud Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact Type No. Applicable
Lamp
Round Extended
ALGN2
AOLGN2
ALGNE2
AOLGNE2
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALGN29911DNLSTD2NO ALGN29920DN
2NC ALGN29902DN
LED Transformer 1NO-1NC ALGN211DNLSTD-62NO ALGN220DN
2NC ALGN202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLGN29911DNLSTD2NO AOLGN29920DN
2NC AOLGN29902DN
LED Transformer 1NO-1NC AOLGN211DNLSTD-62NO AOLGN220DN
2NC AOLGN202DN
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALGNE29911DNLETD2NO ALGNE29920DN
2NC ALGNE29902DN
LED Transformer 1NO-1NC ALGNE211DNLETD-62NO ALGNE220DN
2NC ALGNE202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLGNE29911DNLETD2NO AOLGNE29920DN
2NC AOLGNE29902DN
LED Transformer 1NO-1NC AOLGNE211DNLETD-62NO AOLGNE220DN
2NC AOLGNE202DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED Transformer BA9S and E12 Types
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
PW: pure white (BA9S type only)
R: red
S: blue
W: white
Y: yellow
Use the white lens (W) for LED pure white illumination.
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
82.5 (4 blocks)
59.5 (2 blocks) 27.5
Panel Thickness 0.8 to 3.5
5.5 23
ø35
ø24
ø27
M3 Terminal Screw
M3.5 Terminal Screw
ø40
40
M3.5 Terminal
Screws
94 (2 blocks)
117 (4 blocks)
23
Panel Thickness 0.8 to 3.5
ø24
ø27
ø35
27.5
ø40
40
M3 Terminal Screw
M3.5 Terminal Screw
97 (4 blocks)
74 (2 blocks) 23.5
Panel Thickness 0.8 to 3.5
5.5 23
ø35
ø24
ø27
ø40
40
M3.5 Terminal
Screws
108.5 (2 blocks)
131.5 (4 blocks)
23
Panel Thickness 0.8 to 3.5
ø24
ø27
ø35
ø40
40
23.5
ALGN2/AOLGN2
BA9S/Full V oltage
ALGNE2/AOLGNE2
E12/Full V oltage ALGNE2/AOLGNE2
E12/Transformer
ALGN2/AOLGN2
BA9S/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
25
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Dimensions
Incandescent Round Extended with Half Shroud Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
Round Extended
ALNG
ALNEGBA9S Momentary
Without Lamp Full Voltage 1NO-1NC ALN9G911LS (1W)2NO ALN9G920
2NC ALN9G902
Incandescent Transformer 1NO-1NC ALN11LS-62NO ALN20
2NC ALN02
E12 Momentary
Without Lamp Full Voltage 1NO-1NC ALNE9G911LE (2W)2NO ALNE9G920
2NC ALNE9G902
Incandescent Transformer 1NO-1NC ALN11LE-82NO ALN20
2NC ALN02
Lens Color Code Operating V oltage Code
Incandescent Illuminated Type Incandescent T ransformer BA9S Type Incandescent Transformer E12 Type
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
C: clear
G: green
O: orange
R: red
S: blue
W: white
1G6: 100/110V AC
11G6: 115V AC
12G6: 120V AC
2G6: 200/220V AC
23G6: 230V AC
24G6: 240V AC
38G6: 380V AC
4G6: 400/440V AC
48G6: 480V AC
1G8: 100/110V AC
11G8: 115V AC
12G8: 120V AC
2G8: 200/220V AC
23G8: 230V AC
24G8: 240V AC
38G8: 380V AC
4G8: 400/440V AC
48G8: 480V AC
M3 Terminal Screw M3.5 Terminal Screw
81 (4 blocks)
58 (2 blocks) 23
Panel Thickness 0.8 to 4
623
ø35
ø24.6
ø27
36
40
M3.5 Terminal
Screws
92 (2 blocks)
115 (4 blocks)
23
Panel Thickness 0.8 to 4
ø24.6
ø27
ø35
23
36
40
88 (4 blocks)
65 (2 blocks) 23
Panel Thickness 0.8 to 4
623
ø35
ø24.6
ø27
M3 Terminal Screw M3.5 Terminal Screw
36
40
M3.5 Terminal
Screws
99 (2 blocks)
122 (4 blocks)
23
Panel Thickness 0.8 to 4
ø24.6
ø27
ø35
36
40
23
ALN
G Momentary
BA9S/Full V oltage
ALNE
G Momentary
E16/Full V oltage ALNE
G Momentary
E16/Transformer
ALN
G Momentary
BA9S/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
26
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Dimensions
LED Round Extended with Full Shroud Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact Type No. Applicable
Lamp
Round Extended
ALFN2
AOLFN2
ALFNE2
AOLFNE2
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALFN29911DNLSTD2NO ALFN29920DN
2NC ALFN29902DN
LED Transformer 1NO-1NC ALFN211DNLSTD-62NO ALFN220DN
2NC ALFN202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLFN29911DNLSTD2NO AOLFN29920DN
2NC AOLFN29902DN
LED Transformer 1NO-1NC AOLFN211DNLSTD-62NO AOLFN220DN
2NC AOLFN202DN
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALFNE29911DNLETD2NO ALFNE29920DN
2NC ALFNE29902DN
LED Transformer 1NO-1NC ALFNE211DNLETD-62NO ALFNE220DN
2NC ALFNE202DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLFNE29911DNLETD2NO AOLFNE29920DN
2NC AOLFNE29902DN
LED Transformer 1NO-1NC AOLFNE211DNLETD-62NO AOLFNE220DN
2NC AOLFNE202DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED Transformer BA9S and E12 Types
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
PW: pure white (BA9S type only)
R: red
S: blue
W: white
Y: yellow
Use the white lens (W) for LED pure white illumination.
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
M3 Terminal
Screw M3.5 Terminal Screw
84.5 (4 blocks)
61.5 (2 blocks) 25
Panel Thickness 0.8 to 5.5
5.5 23
ø35
ø29.5
ø40
40
M3.5 Terminal
Screws
96 (2 blocks)
119 (4 blocks)
23
Panel Thickness 0.8 to 5.5
ø29.5
ø35
25
ø40
40
99.5 (4 blocks)
76.5 (2 blocks) 21
Panel Thickness 0.8 to 6
523
ø35
ø29.5
M3 Terminal Screw M3.5 Terminal Screw
ø40
40
M3.5 Terminal
Screws
111 (2 blocks)
134 (4 blocks)
23
Panel Thickness 0.8 to 6
ø29.5
ø35
ø40
40
21
ALFN2/AOLFN2
BA9S/Full V oltage ALFN2/AOLFN2
BA9S/Transformer
ALFNE2/AOLFNE2
E12/Transformer
ALFNE2/AOLFNE2
E12/Full V oltage
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
27
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Dimensions
Incandescent Round Extended with Full Shroud Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
Round Extended
ALNF
ALNEF
AOLNF
AOLNEF
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALN9F911LS (1W)2NO ALN9F920
2NC ALN9F902
Incandescent Transformer 1NO-1NC ALN11LS-62NO ALN20
2NC ALN02
Maintained
Without Lamp Full Voltage 1NO-1NC AOLN9F911LS (1W)2NO AOLN9F920
2NC AOLN9F902
Incandescent Transformer 1NO-1NC AOLN11LS-62NO AOLN20
2NC AOLN02
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALNE9F911LE (2W)2NO ALNE9F920
2NC ALNE9F902
Incandescent Transformer 1NO-1NC ALN11LE-82NO ALN20
2NC ALN02
Maintained
Without Lamp Full Voltage 1NO-1NC AOLNE9F911LE (2W)2NO AOLNE9F920
2NC AOLNE9F902
Incandescent Transformer 1NO-1NC AOLN11LE-82NO AOLN20
2NC AOLN02
Lens Color Code Operating V oltage Code
Incandescent Illuminated Type Incandescent T ransformer BA9S Type Incandescent Transformer E12 Type
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
C: clear
G: green
O: orange
R: red
S: blue
W: white
1F6: 100/110V AC
11F6: 115V AC
12F6: 120V AC
2F6: 200/220V AC
23F6: 230V AC
24F6: 240V AC
38F6: 380V AC
4F6: 400/440V AC
48F6: 480V AC
1F8: 100/110V AC
11F8: 115V AC
12F8: 120V AC
2F8: 200/220V AC
23F8: 230V AC
24F8: 240V AC
38F8: 380V AC
4F8: 400/440V AC
48F8: 480V AC
M3 Terminal
Screw
M3.5 Terminal
Screw
83 (4 blocks)
60 (2 blocks) 21
Panel Thickness
0.8 to 5
623
ø35
ø29.5
M3.5 Terminal
Screws
94 (2 blocks)
117 (4 blocks)
23
Panel Thickness
0.8 to 5
ø29.5
ø35
21 105 (4 blocks)
82 (2 blocks) 21
Panel Thickness
0.8 to 5
623
ø35
ø29.5
M3 Terminal
Screw
M3.5 Terminal
Screw M3.5 Terminal
Screws
116 (2 blocks)
139 (4 blocks)
23
Panel Thickness 0.8 to 5
ø29.5
ø35
36
40
21
90 (4 blocks)
67 (2 blocks) 21
Panel Thickness
0.8 to 5
623
ø35
ø29.5
M3 Terminal
Screw
M3.5 Terminal
Screw M3.5 Terminal
Screws
101 (2 blocks)
124 (4 blocks)
23
Panel Thickness
0.8 to 5
ø29.5
ø35
21 112 (4 blocks)
89 (2 blocks) 21
Panel Thickness
0.8 to 5
623
ø35
ø29.5
M3 Terminal
Screw
M3.5 Terminal
Screw M3.5 Terminal
Screws
123 (2 blocks)
146 (4 blocks)
23
Panel Thickness 0.8 to 5
ø29.5
ø35
36
40
21
ALN
F Momentary
BA9S/Full Voltage AOLN
F Maintained
BA9S/Full V oltage
ALN
F Momentary
BA9S/Transformer ALON
F Maintained
BA9S/Transformer
ALNE
F Momentary
E12/Full V oltage ALN
F Momentary
E12/Transformer AOLNE
F Maintained
E12/Full V oltage AOLN
F Maintained
E12/Transformer
ø30 Series Illuminated Pushbuttons
28
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Dimensions
LED Mushroom (ø40) Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
ø40 Mushroom
ALN3
AOLN3
ALNE3
AOLNE3
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALN39911DNLSTD2NO ALN39920DN
2NC ALN39902DN
LED Transformer 1NO-1NC ALN311DNLSTD-62NO ALN320DN
2NC ALN302DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLN39911DNLSTD2NO AOLN39920DN
2NC AOLN39902DN
LED Transformer 1NO-1NC AOLN311DNLSTD-62NO AOLN320DN
2NC AOLN302DN
E12
Momentary
Without Lamp Full Voltage 1NO-1NC ALNE39911DNLETD2NO ALNE39920DN
2NC ALNE39902DN
LED Transformer 1NO-1NC ALNE311DNLETD-62NO ALNE320DN
2NC ALNE302DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLNE39911DNLETD2NO AOLNE39920DN
2NC AOLNE39902DN
LED Transformer 1NO-1NC AOLNE311DNLETD-62NO AOLNE320DN
2NC AOLNE302DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED Transformer BA9S and E12 Types
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
86 (4 blocks)
63 (2 blocks) 23.5
Panel Thickness 0.8 to 7.5
5.5 23
ø40
M3 Terminal Screw M3.5 Terminal Screw
36
40
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
23.5
36
40
100.5 (4 blocks)
77.5 (2 blocks) 20
Panel Thickness 0.8 to 7.5
5.5 23
ø40
M3 Terminal Screw M3.5 Terminal Screw
36
40
M3.5 Terminal
Screws
112 (2 blocks)
135 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
36
40
20
ALN3/AOLN3
BA9S/Full V oltage ALN3/AOLN3
BA9S/Transformer
ALNE3/AOLNE3
E12/Full V oltage ALNE3/AOLNE3
E12/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
29
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC).
Dimensions
Incandescent Square and Rectangular Extended Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
Square Extended
ULQN
UOLQN BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ULQN9911LS (1W)2NO ULQN9920
2NC ULQN9902
Incandescent Transformer 1NO-1NC ULQN11LS-62NO ULQN20
2NC ULQN02
Maintained
Without Lamp Full Voltage 1NO-1NC UOLQN9911LS (1W)2NO UOLQN9920
2NC UOLQN9902
Incandescent Transformer 1NO-1NC UOLQN11LS-62NO UOLQN20
2NC UOLQN02
Rectangular (Marking Type)
ULQNB
UOLQNBBA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ULQN9B911LS (1W)2NO ULQN9B920
2NC ULQN9B902
Incandescent Transformer 1NO-1NC ULQN11LS-62NO ULQN20
2NC ULQN02
Maintained
Without Lamp Full Voltage 1NO-1NC UOLQN9B911LS (1W)2NO UOLQN9B920
2NC UOLQN9B902
Incandescent Transformer 1NO-1NC UOLQN11LS-62NO UOLQN20
2NC UOLQN02
Lens Color Code Operating V oltage Code
Incandescent Illuminated Type Incandescent T ransformer
Square Extended Type Incandescent Transformer
Rectangular Marking Type
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
C: clear (square type only)
G: green
O: orange
R: red
S: blue
W: white
Clear lens is not available for the rectangular type.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC
1B6: 100/110V AC
11B6: 115V AC
12B6: 120V AC
2B6: 200/220V AC
23B6: 230V AC
24B6: 240V AC
38B6: 380V AC
4B6: 400/440V AC
48B6: 480V AC
M3.5 Terminal
Screws
120 (2 blocks)
143 (4 blocks)
23
Panel Thickness 0.8 to 3.2
25
36.4×42.4
52.2
30×36
44
36.4×42.4
30×36
109 (4 blocks)
86 (2 blocks) 25
Panel Thickness
0.8 to 3.2
623
M3 Terminal
Screw
M3.5 Terminal
Screw
M3.5 Terminal
Screws
98 (2 blocks)
121 (4 blocks)
23
Panel Thickness
0.8 to 3.2
25
36.4×42.4
30×36
109 (4 blocks)
86 (2 blocks) 20
Panel Thickness
0.8 to 3.2
623 14
34
25
M3 Terminal
Screw
M3.5 Terminal
Screws M3.5 Terminal
Screws
120 (2 blocks)
143 (4 blocks)
23
Panel Thickness
0.8 to 3.2
25
34
36
52.2
20 14 40
44
ULQN Momentary
BA9S/Full V oltage UOLQN Maintained
BA9S/Full V oltage UOLQN Maintained
BA9S/Transformer
87 (4 blocks)
64 (2 blocks) 25
Panel Thickness
0.8 to 3.2
623
36.4×42.4
30×36
M3 Terminal
Screw
M3.5 Terminal
Screws
87 (4 blocks)
64 (2 blocks) 20
Panel Thickness
0.8 to 3.2
623 14
34
25
M3 Terminal
Screw
M3.5 Terminal
Screw
ULQN
B Momentary
BA9S/Full V oltage
M3.5 Terminal
Screws
98 (2 blocks)
121 (4 blocks)
23
Panel Thickness
0.8 to 3.2
25
34
20 14
ULQN
B Momentary
BA9S/Transformer
ULQN Momentary
BA9S/Transformer
UOLQN
B Maintained
BA9S/Transformer
UOLQN
B Maintained
BA9S/Full V oltage
ø30 Series Illuminated Pushbuttons
30
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC).
Push T urn Lock: Knob is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise.
Dimensions
Incandescent Push Turn Lock Switches
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
ALNL
BA9S Push Turn Lock
Without Lamp Full Voltage
1NO-1NC ALN9L911
LS (1W)2NO ALN9L920
2NC ALN9L902
Incandescent Transformer
1NO-1NC ALN11
LS-62NO ALN20
2NC ALN02
Lens Color Code Operating V oltage Code
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
G: green
O: orange
R: red
S: blue
W: white
1L6: 100/110V AC
11L6: 115V AC
12L6: 120V AC
2L6: 200/220V AC
23L6: 230V AC
24L6: 240V AC
38L6: 380V AC
4L6: 400/440V AC
48L6: 480V AC
90 (4 blocks)
67 (2 blocks) 25
Panel Thickness 0.8 to 5
623
ø35
ø22
M3 Terminal Screw M3.5 Terminal Screw
36
40
M3.5 Terminal
Screws
101 (2 blocks)
124 (4 blocks)
23
Panel Thickness 0.8 to 5
25
36
40
ø35
ø22
ALN
L
BA9S/Full V oltage ALN
L
BA9S/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
31
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Pushlock T urn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only.
Note: AVNL3 and AVNLE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are
required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant).
Push T urn Lock: Lens is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise.
Dimensions
LED Pushlock Turn Reset / Push Turn Lock Types
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
ø40 Mushroom
Pushlock Turn Reset
AVLN3
AVLNE3 BA9S Pushlock
Turn Reset
Without Lamp Full Voltage 1NO-1NC AVLN39911DNR LSTD2NO AVLN39920DNR
2NC AVLN39902DNR
LED Transformer 1NO-1NC AVLN311DNR LSTD-62NO AVLN320DNR
2NC AVLN302DNR
E12 Pushlock
Turn Reset
Without Lamp Full Voltage 1NO-1NC AVLNE39911DNR LETD2NO AVLNE39920DNR
2NC AVLNE39902DNR
LED Transformer 1NO-1NC AVLNE311DNR LETD-62NO AVLNE320DNR
2NC AVLNE302DNR
ø40 Mushroom
Push Turn Lock
AJLN3
BA9S Push Turn
Lock
Without Lamp Full Voltage
1NO-1NC AJLN39911DN
LSTD2NO AJLN39920DN
2NC AJLN39902DN
LED Transformer
1NO-1NC AJLN311DN
LSTD-6
2NO AJLN320DN
2NC AJLN302DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED T ransformer BA9S Types
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
R: red
W: white
Y: yellow
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
86 (4 blocks)
63 (2 blocks) 23.5
5.5 23
Panel Thickness
0.8 to 7.5
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw
100.5 (4 blocks)
77.5 (2 blocks) 20
5.5 23
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw Panel Thickness
0.8 to 7.5
M3.5 Terminal
Screws
112 (2 blocks)
135 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
36
40
20
86 (4 blocks)
63 (2 blocks) 23.5
Panel Thickness
0.8 to 7.5
5.5 23
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw
AVLN3
BA9S/Full V oltage AVLN3
BA9S/Transformer AVLNE3
E12/Full V oltage AVLNE3
E12/Transformer
AJLN3
BA9S/Full V oltage
K
P
U
H
O
L
S
C
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
36
40
23.5
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
23
Panel Thickness
0.8 to 7.5
ø40
23.5
AJLN3
BA9S/Transformer
All dimensions in mm.
ø30 Series Illuminated Pushbuttons
32
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63.
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Pushlock T urn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only.
Note: AVNL3 and AVNLE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are
required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant).
Push T urn Lock: Lens is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise.
Dimensions
Incandescent Pushlock Turn Reset / Push Turn Lock Types
Shape Lamp
Receptacle Operation
Type Lamp Input T ype Contact Type No. Applicable
Lamp
ø40 Mushroom
Pushlock Turn Reset
AVLN3
AVLNE3 BA9S Pushlock
Turn Reset
Without Lamp Full Voltage 1NO-1NC AVLN39911NR LS (1W)2NO AVLN39920NR
2NC AVLN39902NR
Incandescent Transformer 1NO-1NC AVLN311NR LS-62NO AVLN320NR
2NC AVLN302NR
E12 Pushlock
Turn Reset
Without Lamp Full Voltage 1NO-1NC AVLNE39911NR LE (2W)2NO AVLNE39920NR
2NC AVLNE39902NR
Incandescent Transformer 1NO-1NC AVLNE311NR LE-82NO AVLNE320NR
2NC AVLNE302NR
ø40 Mushroom
Push Turn Lock
AJLN3
BA9S Push Turn
Lock
Without Lamp Full Voltage
1NO-1NC AJLN39911N
LS (1W)2NO AJLN39920N
2NC AJLN39902N
Incandescent Transformer
1NO-1NC AJLN311N
LS-6
2NO AJLN320N
2NC AJLN302N
Lens Color Code Operating V oltage Code
Incandescent Illuminated Type Incandescent T ransformer BA9S Type Incandescent Transformer E12 Type
Specify a lens color code in place of in the Type No. Specify an operating voltage code in place of in the Type No.
G: green
O: orange
R: red
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
86 (4 blocks)
63 (2 blocks) 23.5
5.5 23
Panel Thickness
0.8 to 7.5
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw
100.5 (4 blocks)
77.5 (2 blocks) 20
5.5 23
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw Panel Thickness
0.8 to 7.5
M3.5 Terminal
Screws
112 (2 blocks)
135 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
36
40
20
86 (4 blocks)
63 (2 blocks) 23.5
Panel Thickness
0.8 to 7.5
5.5 23
ø40
M3 Terminal
Screw
M3.5 Terminal
Screw
AVLN3
BA9S/Full V oltage AVLN3
BA9S/Transformer AVLNE3
E12/Full V oltage AVLNE3
E12/Transformer
AJLN3
BA9S/Full V oltage
K
P
U
H
O
L
S
C
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
23
Panel Thickness 0.8 to 7.5
ø40
36
40
23.5
M3.5 Terminal
Screws
97.5 (2 blocks)
120.5 (4 blocks)
23
Panel Thickness
0.8 to 7.5
ø40
23.5
AJLN3
BA9S/Transformer
All dimensions in mm.
ø30 Series Selector Switches
33
ø30
ASN Selector Switches (Knob Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Right Maintained Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASN310 ASN410
——
2Dummy
11
(1NO-1NC) 1NO ASN311 ASN411
2NC
20
(2NO) 1NO ASN320 ASN420
2NO
22
(2NO-2NC)
1NO ASN322 ASN422
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN37S ASN47S
2NC
10
(1NO) 1NO
——
ASN3010 ASN4010
2Dummy
11
(1NO-1NC) 1NO ASN3011 ASN4011
2NC
20
(2NO) 1NO ASN3020 ASN4020
2NO
22
(2NO-2NC)
1NO ASN3022 ASN4022
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN307S ASN407S
2NC
45° 3-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Left Maintained Spring Return
from Right
Mounting
Position Type LCR
11
(1NO-1NC) 1NO ASN111 ASN211
——
2NC
22
(2NO-2NC)
1NO ASN122 ASN222
2NC
3NO
4NC
5S
(2NO-2NC)
1NO ASN15S ASN25S
2NO
3NC
4NC
7S
(2NC) 1NC ASN17S ASN27S
2NC
8S
(4NC)
1NC ASN18S ASN28S
2NC
3NC
4NC
11
(1NO-1NC) 1NO
——
ASN1011 ASN2011
2NC
22
(2NO-2NC)
1NO ASN1022 ASN2022
2NC
3NO
4NC
5S
(2NO-2NC)
1NO ASN105S ASN205S
2NC
3NO
4NC
7S
(2NC) 1NC ASN107S ASN207S
2NC
8S
(4NC)
1NC ASN108S ASN208S
2NC
3NC
4NC
Knob: Black
Round bezel (metal): Chrome-plated
Units marked with differ in shape.
See page 36 for dimensions.
Nameplates are ordered separately.
1
3
2
4
ASN
L R L R
L R
L R
C
L R C
LR
C
LR
C
LR
ø30 Series Selector Switches
34
ø30
ASN Selector Switches (Lever Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Right Maintained Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASN3L10 ASN4L10
——
2Dummy
11
(1NO-1NC) 1NO ASN3L11 ASN4L11
2NC
20
(2NO) 1NO ASN3L20 ASN4L20
2NO
22
(2NO-2NC)
1NO ASN3L22 ASN4L22
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN3L7S ASN4L7S
2NC
10
(1NO) 1NO
——
ASN30L10 ASN40L10
2Dummy
11
(1NO-1NC) 1NO ASN30L11 ASN40L11
2NC
20
(2NO) 1NO ASN30L20 ASN40L20
2NO
22
(2NO-2NC)
1NO ASN30L22 ASN40L22
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN30L7S ASN40L7S
2NC
45° 3-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Left Maintained Spring Return
from Right
Mounting
Position Type LCR
11
(1NO-1NC) 1NO ASN1L11 ASN2L11
——
2NC
22
(2NO-2NC)
1NO ASN1L22 ASN2L22
2NC
3NO
4NC
5S
(2NO-2NC)
1NO ASN1L5S ASN2L5S
2NO
3NC
4NC
7S
(2NC) 1NC ASN1L7S ASN2L7S
2NC
8S
(4NC)
1NC ASN1L8S ASN2L8S
2NC
3NC
4NC
11
(1NO-1NC) 1NO
——
ASN10L11 ASN20L11
2NC
22
(2NO-2NC)
1NO ASN10L22 ASN20L22
2NC
3NO
4NC
5S
(2NO-2NC)
1NO ASN10L5S ASN20L5S
2NC
3NO
4NC
7S
(2NC) 1NC ASN10L7S ASN20L7S
2NC
8S
(4NC)
1NC ASN10L8S ASN20L8S
2NC
3NC
4NC
ASNLLever: Black
Round bezel (metal): Chrome-plated
Units marked with differ in shape.
See page 36 for dimensions.
Nameplates are ordered separately.
1
3
2
4
L R L R
L R
L R
C
LRC
LR
C
LR
C
LR
ø30 Series Selector Switches
35
ø30
ASN Key Selector Switches
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Right Maintained Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASN3K10 ASN4K10
——
2Dummy
11
(1NO-1NC) 1NO ASN3K11 ASN4K11
2NC
20
(2NO) 1NO ASN3K20 ASN4K20
2NO
22
(2NO-2NC)
1NO ASN3K22 ASN4K22
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN3K7S ASN4K7S
2NC
10
(1NO) 1NO
——
ASN30K10 ASN40K10
2Dummy
11
(1NO-1NC) 1NO ASN30K11 ASN40K11
2NC
20
(2NO) 1NO ASN30K20 ASN40K20
2NO
22
(2NO-2NC)
1NO ASN30K22 ASN40K22
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN30K7S ASN40K7S
2NC
45° 3-position
Contact
Code
(ASN)
Contact Block Operator Position Maintained Spring Return
from Left Maintained Spring Return
from Right
Mounting
Position Type LCR
11
(1NO-1NC) 1NO ASN1K11 ASN2K11
——
2NC
22
(2NO-2NC)
1NO ASN1K22 ASN2K22
2NC
3NO
4NC
5S
(1NO-1NC)
(1NO-1NC)
1NO ASN1K5S ASN2K5S
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN1K7S ASN2K7S
2NC
8S
(2NO-2NC)
1NO ASN1K8S ASN2K8S
2NC
3NO
4NC
11
(1NO-1NC) 1NO
——
ASN10K11 ASN20K11
2NC
22
(2NO-2NC)
1NO ASN10K22 ASN20K22
2NC
3NO
4NC
5S
(1NO-1NC)
(1NO-1NC)
1NO ASN10K5S ASN20K5S
2NC
3NO
4NC
7S
(1NO-1NC) 1NO ASN10K7S ASN20K7S
2NC
8S
(2NO-2NC)
1NO ASN10K8S ASN20K8S
2NC
3NO
4NC
Cylinder: Chrome-plated
Round bezel (metal): Chrome-plated
On the spring-returned types, the keys can be released
only from the maintained position. On the maintained
types, the key can be released from every position. Key
retained positions are also available. See page 12.
Key selector switch is supplied with two standard keys.
Two different keys are available upon request.
Nameplates are ordered separately.
ASNK
1
2
3
4
L R L R
L R
L R
C
LRC
LR
C
LR
C
LR
ø30 Series Selector Switches
36
ø30
Dimensions
Knob Operator Type
Lever Operator Type
Key Selector Type
Contact Block Mounting Position and Contact Arrangement Chart
40
36
623
54 (1 or 2
blocks)
77 (4 blocks)22
ø35
45°
45°
90°
M3.5 Terminal Screw Panel Thickness
0.8 to 7.5
40
36
623
22
ø35
58 (1 or 2
blocks)
81 (4 blocks)
45°
45°
M3.5 Terminal Screw Panel Thickness
0.8 to 7.5
Dimensions of knob operator type marked with
M3.5 Terminal Screw
40
36
23
54 (1 or 2
blocks)
77 (4 blocks)
Panel Thickness
0.8 to 7.5
6
27
45°
45°
90°
ø35
25.0
40
36
623
58 (1 or 2
blocks)
81 (4 blocks)
ø35
25.0
26.5
45°
45°
M3.5 Terminal Screw Panel Thickness
0.8 to 7.5
Dimensions of lever operator type marked with
40
36
23
54 (1 or 2
blocks)
77 (4 blocks)
ø35
6
22 22
24.5
M3.5 Terminal Screw Panel Thickness
0.8 to 7.5
90°
45°
45°
All dimensions in mm.
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
1
2
3
4
ø30 Series Selector Switches
37
ø30
Notes:
1.The operator of the 2-way spring return unit may slightly deviate from the center position.
2.Turn the operator to each position accurately.
ASTN Selector Switches (Knob Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Right ——
Mounting
Position Type LR
11
(1NO-1NC) 1NO ASTN3211 ASTN4211
——
2NC
22
(2NO-2NC)
1NO ASTN3222 ASTN4222
2NO
3NC
4NC
45° 3-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Left Spring Return
from Right Spring Return
Two-way
Mounting
Position Type LCR
22
(2NO-2NC)
1NO ASTN1122 ASTN2122 ASTN20122 ASTN5122
2NO
3NC
4NC
22
(2NO-2NC)
1NO ASTN1222 ASTN2222 ASTN20222 ASTN5222
2NO
3NC
4NC
40
(4NC)
1NO ASTN1340
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASTN1422 ASTN20422
2NC
3NC
4NO
20
(2NO) 1NO ASTN1520 ASTN20520
2NO
40
(4NO)
1NO ASTN1540 ASTN20540
2NO
3NO
4NO
11
(1NO-1NC) 1NC ASTN1611
2NO
22
(2NO-2NC)
1NC ASTN1622
2NO
3NC
4NO
11
(1NO-1NC) 1NO ———ASTN5111
2NC
ASTN Knob operator: Black
Round bezel (metal): Chrome-plated
L R L R
C
LRC
LR
C
LR
C
LR
40
ø35
27
623
36
M3.5 Terminal Screw
Panel Thickness
0.8 to 7.5
81 (4 blocks)
58 (2 blocks)
90°
45°
45°
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
1
2
3
4
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
ø30 Series Selector Switches
38
ø30
Notes:
1. The operator of the 2-way spring return unit may slightly deviate from the center position.
2. Turn the operator to each position accurately.
ASTN Selector Switches (Lever Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Right ——
Mounting
Position Type LR
11
(1NO-1NC) 1NO ASTN32L11 ASTN42L11
——
2NC
22
(2NO-2NC)
1NO ASTN32L22 ASTN42L22
2NO
3NC
4NC
45° 3-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Left Spring Return
from Right Spring Return
Two-way
Mounting
Position Type LCR
22
(2NO-2NC)
1NO ASTN11L22 ASTN21L22 ASTN201L22 ASTN51L22
2NO
3NC
4NC
22
(2NO-2NC)
1NO ASTN12L22 ASTN22L22 ASTN202L22 ASTN52L22
2NO
3NC
4NC
40
(4NC)
1NO ASTN13L40
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASTN14L22 ASTN204L22
2NC
3NC
4NO
20
(2NO) 1NO ASTN15L20 ASTN205L20
2NO
40
(4NO)
1NO ASTN15L40 ASTN205L40
2NO
3NO
4NO
11
(1NO-1NC) 1NC ASTN16L11
2NO
22
(2NO-2NC)
1NC ASTN16L22
2NO
3NC
4NO
11
(1NO-1NC) 1NO ———ASTN51L11
2NC
ASTNLLever operator: Black
Round bezel (metal): Chrome-plated
L R L R
C
LRC
LR
C
LR
C
LR
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
1
2
3
4
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
40
623
ø35
29
36
25.0
M3.5 Terminal Screw
Panel Thickness
0.8 to 7.5
58 (1 or 2
blocks)
81 (4 blocks)
90°
45°
45°
ø30 Series Selector Switches
39
ø30
Notes:
1.The operator of the 2-way spring return unit may slightly deviate from the center position.
2.Turn the operator to each position accurately.
ASTN Key Selector Switches
No. of Positions
Shape
Contact Arrangement Chart
90° 2-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Right ——
Mounting
Position Type LR
11
(1NO-1NC) 1NO ASTN32K11 ASTN42K11
——
2NC
22
(2NO-2NC)
1NO ASTN32K22 ASTN42K22
2NO
3NC
4NC
45° 3-position
Contact
Code
(ASTN)
Contact Block Operator Position Maintained Spring Return
from Left Spring Return
from Right Spring Return
Two-way
Mounting
Position Type LCR
22
(2NO-2NC)
1NO ASTN11K22 ASTN21K22 ASTN201K22 ASTN51K22
2NO
3NC
4NC
22
(2NO-2NC)
1NO ASTN12K22 ASTN22K22 ASTN202K22 ASTN52K22
2NO
3NC
4NC
40
(4NC)
1NO ASTN13K40
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASTN14K22 ASTN204K22
2NC
3NC
4NO
20
(2NO) 1NO ASTN15K20 ASTN205K20
2NO
40
(4NO)
1NO ASTN15K40 ASTN205K40
2NO
3NO
4NO
11
(1NO-1NC) 1NC ASTN16K11
2NO
22
(2NO-2NC)
1NC ASTN16K22
2NO
3NC
4NO
11
(1NO-1NC) 1NO ———ASTN51K11
2NC
ASTNKCylinder: Chrome-plated
Round bezel (metal): Chrome-plated
On the spring-returned types, the keys can be
released only from the maintained position.
On the maintained types, the k e y can be released
from every position. Key retained positions are
also available. See page 12.
L R L R
C
LRC
LR
C
LR
C
LR
80 (4 blocks)
57 (1 or 2
blocks)
623
ø35
38
16.5 40
40
M3.5 Terminal Screw
Panel Thickness
0.8 to 7.5
45°
45°
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
1
2
3
4
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
ø30 Series Illuminated Selector Switches
40
ø30
90° 2-position
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer type contains an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC).
On the 2-position selector switches marked with above, the contact operation is reversed as follows.
Illuminated Selector Switches
Shape
Contact Arrangement Chart
Contact
Code
Contact
Block Operator
Position Lamp Input Type
Maintained Spring Return
from Right Spring Return
from Left
Mounting
Position Type LR
11
(1NO-1NC)
1NO Without Lamp Full Voltage ASLN29911NASLN219911NASLN229911N
2NC LED Transformer ASLN211DNASLN2111DNASLN2211DN
Incandescent Transformer ASLN211NASLN2111NASLN2211N
20
(2NO)
1NO Without Lamp Full Voltage ASLN29920NASLN219920NASLN229920N
2NO LED Transformer ASLN220DNASLN2120DNASLN2220DN
Incandescent Transformer ASLN220NASLN2120NASLN2220N
22
(2NO-2NC)
1NO Without Lamp Full Voltage ASLN29922NASLN219922NASLN229922N
2NC
3NO LED Transformer ASLN222DNASLN2122DNASLN2222DN
4NC
Incandescent Transformer ASLN222NASLN2122NASLN2222N
LED Illuminated Type Incandescent Illuminated Type Operating V oltage Code
Lens/LED Color Code Lens Color Code
Specify a lens/LED color code in
place of in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
Specify a lens color code in place of
in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
156: 115V AC
136: 120V AC
26: 200/220V AC
236: 230V AC
256: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
ASLN (Base BA9S)
L R
L R
L R
[Example]
1
2
3
4
LR
1NO
2NO
3NC
4NC
RightLeft
Operator
Position
40
ø40
235.5
28
9
ø35
ø25
M3.5 Terminal Screws
M3 Terminal Screw
63 (2 blocks)
A: 86 (4 blocks)
B: 97.5 (2 blocks), 120.5 (4 blocks)
Panel Thickness
0.8 to 7.5
(including nameplate)
90°
45°
45°
Contact Block Mounting Position
and Contact Arrangement Chart Dimensions
A: Full voltage type
B: Transf ormer type
ø30 Series Illuminated Selector Switches
41
ø30
45° 3-position
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC).
Illuminated Selector Switches
Contact
Code
Contact
Block Operator
Position Lamp
Input Type
Maintained Spring Return
from Right Spring Return
from left Spring Return
Two-way
Mounting
Position Type LCR
20
(2NO)
1NO Without Lamp
Full V oltage ASLN39920NASLN319920NASLN329920NASLN339920N
2NO LED
Transformer ASLN320DNASLN3120DNASLN3220DNASLN3320DN
Incandescent
Transformer ASLN320NASLN3120NASLN3220NASLN3320N
02
(2NC)
1NC Without Lamp
Full V oltage ASLN39902NASLN319902NASLN329902NASLN339902N
2NC LED
Transformer ASLN302DNASLN3102DNASLN3202DNASLN3302DN
Incandescent
Transformer ASLN302NASLN3102NASLN3202NASLN3302N
22
(2NO-2NC)
1NO Without Lamp
Full V oltage ASLN39922NASLN319922NASLN329922NASLN339922N
2NO
3NC LED
Transformer ASLN322DNASLN3122DNASLN3222DNASLN3322DN
4NC Incandescent
Transformer ASLN322NASLN3122NASLN3222NASLN3322N
40
(4NO)
1NO Without Lamp
Full V oltage ASLN39940NASLN319940NASLN329940NASLN339940N
2NO
3NO LED
Transformer ASLN340DNASLN3140DNASLN3240DNASLN3340DN
4NO Incandescent
Transformer ASLN340NASLN3140NASLN3240NASLN3340N
04
(4NC)
1NC Without Lamp
Full V oltage ASLN39904NASLN319904NASLN329904NASLN339904N
2NC
3NC LED
Transformer ASLN304DNASLN3104DNASLN3204DNASLN3304DN
4NC Incandescent
Transformer ASLN304NASLN3104NASLN3204NASLN3304N
LED Illuminated Type Incandescent Illuminated Type Operating V oltage Code
Lens/LED Color Code Lens Color Code
Specify a lens/LED color code in
place of in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
Specify a lens color code in place of
in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
156: 115V AC
136: 120V AC
26: 200/220V AC
236: 230V AC
256: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
C
LRC
LR
C
LR
C
LR
1
2
3
4
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
40
ø40
235.5
28
9
ø35
ø25
M3.5 Terminal Screws
M3 Terminal Screw
63 (2 blocks)
A: 86 (4 blocks)
B: 97.5 (2 blocks), 120.5 (4 blocks)
Panel Thickness
0.8 to 7.5
(including nameplate)
90°
45°
45°
Contact Block Mounting Position
and Contact Arrangement Chart Dimensions
A: Full Voltage type
B: Transf ormer type
ø30 Series Selector Pushbuttons
42
ø30
Specify a button color code in place of in the Type No.
Ring/Lever (metal): Chrome-plated
Notes
1. Circuit Codes A, B, C, and I: When the ring or lever operator is turned, the button is pushed in.
2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever
operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button.
3. Circuit Codes G and H: The pushbutton does not operate when the ring or lever operator is turned to the left position.
4. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure
may be caused.
Ring Operator Type / Lever Operator Type Selector Pushbuttons
Shape Contact
Code Circuit
Code
Contact
Block
Ring/Lever
Ring
Operator Lever
Operator Button
Color
Code
Pushbutton Type No. Type No.
Mounting
Position Type Normal Push Normal Push
11
(1NO-1NC)
A1NO ABN6111ABN6L111
B: black
G: green
R: red
Y: yellow
2NC
I1NC ABN6411ABN6L411
2NO
G1NO Blocked ABN9111ABN9L111
2NC
20
(2NO) D1NO ABN7120
2NO
22
(2NO-2NC)
B
1NC
ABN6122ABN6L122
2NC
3NO
4NO
C
1NC
ABN6222ABN6L222
2NC
3NO
4NO
I
1NC
ABN6422ABN6L422
2NC
3NO
4NO
D
1NC
ABN7122ABN7L122
2NC
3NO
4NO
E
1NC
ABN7222ABN7L222
2NC
3NO
4NO
F
1NC
ABN7322ABN7L322
2NC
3NO
4NO
H
1NC
Blocked ABN9122ABN9L122
2NC
3NO
4NO
ABN
M3.5 Terminal Screw
623 41 25 40
ø28
ø35
40
Panel Thickness 0.8 to 7.5
(including namplate)
M3.5 Terminal Screw
623 41 25 40
ø28
ø35
40
23
Panel Thickness 0.8 to 7.5
(including namplate)
ABNL
623 41 40
ø35
40
26
50
M3.5 Terminal Screw Panel Thickness 0.8 to 7.5
(including namplate)
41 40
ø35
40
26
50
623 23
M3.5 Terminal Screw Panel Thickness 0.8 to 7.5
(including namplate)
Ring Operator (90˚ 2-position)
Lever Operator (90˚ 2-position)
50
50
80
80
Normal Push
1
2
3
4
1
3
2
4
ontact
oc
ount
ng
os
t
on
and Contact Arrangement Chart Mounting Hole Layout
Ring Operator Lever Operator
43
ARN/ARNS Series Mono-lever Switches
Single lever offers up to four directions of control
Mono-lever switches operate in four directions using a single
lever. Switch contacts are actuated in the direction in which the
lever is pushed, enabling quick and accurate control in any
desired direction. Ideal for machine tools and industrial
machines. The lever action can be maintained or spring-
returned in any combination.
Also available with interlock mechanism to prevent inadvertent
actuation.
Contact Ratings
Characteristics
Contact Ratings by Utilization Category
Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1).
Specifications
Specifications and Ratings
Contact Block Type BR
Rated Insulation Voltage 600V
Rated Continuous Current 10A
Contact Ratings by Utilization Category
IEC 60947-5-1 AC-15 (A600)
DC-13 (P600)
Operational Voltage 24V 48V 50V 110V 220V 440V
Operational
Current
AC
50/60 Hz AC-12 Control of resistive loads and solid state loads 10A 10A 10A 6A 2A
AC-15 Control of electromagnetic loads (> 72 VA) 10A 7A 5A 3A 1A
DC DC-12 Control of resistive loads and solid state loads 10A 5A 2.2A 1.1A
DC-13 Control of electromagnets 4A 2A 1.1A 0.6A
Contact Arrangement Double-break slow action
Each contact block contains two independent contacts (2NO, 1NO-1NC, or 2NC)
Up to four contact blocks can be mounted
Insulation Resistance 100 M minimum (500V DC megger)
Dielectric Strength Between live and dead parts: 2,500V AC, 1 minute
Mechanical Life 500,000 operations minimum
(Interlocking type: 250,000 operations minimum)
Electrical Life
Operating Temperature –25 to +50°C (no freezing)
Operating Humidity 45 to 85% RH (no condensation)
Lever Knob Black
BR Contact Block
The contact bloc k is made of nylon resin. Each contact bloc k
contains two pairs of doub le-break silver contacts . There are
three types as shown in the diagram below and up to four
contact blocks can be mounted in any direction. A wide vari-
ety of circuits allows diverse combinations of control.
Control Mechanism
When the operator lever is pushed to about 30° in each
direction from the neutral position, the contact in that direc-
tion activates.The lever can operate in two, three, or four
directions, and combinations of maintained or spring-return
from any position are possible.
BR-1E BR-2E BR-3E
(2NO) (1NO-1NC) (2NO)
ø30
ARN/ARNS Series Mono-lever Switches
44
ø30
Modified March 11, 2005 5:32 pm
Types
Specify Contact Arrangement from the table below in place of .
Terminal covers are ordered separately.
Ordering Information
When ordering, specify items to according to the following
example.
[Example]
Operator Type Position Lever Action Type No. Dimensions (mm)
ARN (Long Lever Type) 2-position
(Up-Down)
Maintained ARN2-1010-B
Spring return ARN2-2020-B
2-position
(Left-Right)
Maintained ARN2-0101-B
Spring return ARN2-0202-B
4-position
(Up-Down-Left-Right)
Maintained ARN4-1111-B
Spring return ARN4-2222-B
ARNS (Short Lever Type) 2-position
(Up-Down)
Maintained ARNS2-1010-B
Spring return ARNS2-2020-B
2-position
(Left-Right)
Maintained ARNS2-0101-B
Spring return ARNS2-0202-B
4-position
(Up-Down-Left-Right)
Maintained ARNS4-1111-B
Spring return ARNS4-2222-B
ARNL (Interlocking Type)
The operator le ver is loc ked only in
the center position.
2-position
(Up-Down)
Maintained ARNL2-1010-B
Spring return ARNL2-2020-B
2-position
(Left-Right)
Maintained ARNL2-0101-B
Spring return ARNL2-0202-B
4-position
(Up-Down-Left-Right)
Maintained ARNL4-1111-B
Spring return ARNL4-2222-B
Type No. of
Contact
Blocks Lever Action Contact
Arrangement
Lever
Knob
Color
ARN
ARNS
ARNL
1: 1 block
2: 2 blocks
3: 3 blocks
4: 4 blocks
Order of Entry:
UpRight
DownLeft
1: Maintained
2: Spring return
0: Blocked
Order of Entry:
UpRight
DownLeft
10: 1NO
01: 1NC
11: 1NO-1NC
20: 2NO
02: 2NC
00: Blocked
B: black
Minimum horizontal/vertical mounting centers: 110
30°
M3.5 Terminal
Screw
623
1 block: 47, 2 blocks: 70
3 blocks: 93, 4 blocks: 116
Panel Thickness 0.8 to 6
51
51
ø42
30°
ø22
83
Minimum horizontal/vertical mounting centers: 70
30°
623 63 51
51
ø42
30°
M3.5 Terminal
Screw Panel Thickness
0.8 to 6
ø22
1 block: 47, 2 blocks: 70
3 blocks: 93, 4 blocks: 116
Minimum horizontal/vertical mounting centers: 110
30°
623 51
51
ø42
30°
ø22
83
M3.5 Terminal
Screw Panel Thickness 0.8 to 6
1 block: 47, 2 blocks: 70
3 blocks: 93, 4 blocks: 116
R0.8 max.
0
+0.5
0
+0.2
+0.5
0
4.8
33
ø30.5
68
0
31
68
31 23 64
Panel Cut-Out Mono-Lever with Terminal CoverLever Operator Position
Right
Up
Left Down
ARN 4 – 1012 – 2 0 0 0 0 2 1 1 – B
➀➁
LeftRightUp Down
To calculate the number of contact blocks required, add the number of NO and NC contacts on each pair of adjoining positions (up + right,
right + down, down + left, and left + up). The largest of the four sums is the number of contact b loc ks required. Up to f our contact b locks can
be mounted.
When UL and CSA markings are required on the mono-lever switch, specify as shown below.
[Example] ARN4-1012-20000211-B- U
∗: Contacts marked with do not operate.
Contact Block Position
Terminal No.
Direction of Lever Operation
Terminal No.
Contact
Block
Type
Lever Operation Mode
1: Maintained
2: Spring return
0: Blocked
1012
11NO –––2
BR-2E
3– NC–4
25– NO ––6
BR-1E
7–––NO8
39NO –––10
BR-2E
11 NC 12
413 NC ––14
BR-3E
15 NC 16
ARN/ARNS Series Mono-lever Switches
45
ø30
Modified March 11, 2005 5:32 pm
Accessories and Maintenance Parts
Shape Specification Type No. Ordering Type No. Package Quantity Description
Nameplate MLO
MLO 1
Chrome-plated brass
(matte surface)
MLOPN10 10
Terminal Cover ARN-VL2 ARN-VL2 1
Terminal covers are
ordered separately. When
ordering, specify the Type
No. and the required
quantity.
Order 2 pieces for each
contact block.
Contact Block
(BR Type)
BR-1E BR-1E 1 2NO contact
BR-2E BR-2E 1 1NO-1NC contact
BR-3E BR-3E 1 2NC contact
Bellows ARN-BL ARN-BL 1 For ARN/ARNS
(Locking ring not included)
Bellows
(Interlocking Type) ARNL-BL ARNL-BL 1 For ARNL
(Locking ring not included)
Knob ARNB-ARNB-1
Specify a color code in
place of .
B (blac k), G (green), R (red)
For ARN/ARNS
70
70
ø30.5
46
CS Series Cam Switches
76 standard circuits to choose from
Wide variety of heavy-duty oiltight cam switches
Operators available up to 12 positions
Switches made with a double-pole contact block
Contact blocks rated at 600V, 10A
Ideal for ammeter/voltmeter applications
UL listed and CSA approved
Contact Ratings
Characteristics
Contact Ratings by Utilization Category
Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1).
Specifications
CBS Contact Block
The CBS contact bloc k contains two poles of doub le-break contacts.
The contacts are operated b y a cam designed to perf orm a required
contact operation. Up to six contact blocks can be mounted on a
maintained-action operator base, and up to three contact blocks on
a spring return operator base.
Specifications and Ratings
Rated Insulation Voltage 600V
Rated Continuous Current 10A
Contact Ratings by Utilization Category
IEC 60947-5-1 AC-15 (A600)
DC-13 (P600)
Operational Voltage 24V 110V 220V 440V
Operational
Current
AC
50/60 Hz AC-12 Control of resistive loads and solid state loads 10A 6A 2A
AC-15 Control of electromagnetic loads (> 72 VA) 5A 3A 1A
DC DC-12 Control of resistive loads and solid state loads 8A 3A 1A 0.4A
DC-13 Control of electromagnets 5A 1.2A 0.45A 0.2A
Contact Arrangement Double-break slow action contacts
Two contacts in one deck
Up to 6 decks available (Spring-return type: Up to 3 decks)
Operation Maintained Spring return
Angle 30°, 45°, 60°, 90° 45°
Operator Positions 2 to 12 2, 3, 4
Insulation Resistance 100 M (500V DC megger)
Dielectric Strength 2500V AC, 1 minute (between live and dead parts)
Mechanical Life 1 to 3 decks: 500,000 operations
4 to 6 decks: 200,000 operations
Electrical Life 500,000 operations minimum
Operating Temperature –20 to +50°C (no freezing)
(except ACSSO and ACSSK)
M3.5 Screw Terminal
ø30/ø25
CS Series Cam Switches
47
ø30/ø25
Types
For handles and accessories, see page 49.
Dimensions
T ype Contact
Block Decks Positions Angle Spring
Return Handle Contact
Arrange-
ment Name-
plate
ø30 Series ø25 Series
ACSNO ACSSO
Maintained:
1 to 6 decks
Spring return:
1 to 3 decks
Maintained:
2 to 12 positions
Spring return:
2 to 4 positions
Maintained:
30°, 45°, 60°, 90°
Spring return:
45° only
Spring return
from right
Spring return
from left
Spring return
two-way
Y2, S2, P2,
F2, 25S2
(25S2 is for
ACSSO only)
(one speci-
fied handle
supplied)
See
page 51.
See
page 56.
(ordered
sepa-
rately)
ACSNK ACSSK
Maintained:
1 to 6 decks
Spring return:
1 to 3 decks
Maintained:
2 to 8 positions
Spring return:
2 to 4 positions
Maintained:
45°, 90°
Spring return:
45° only
Spring return
from right
Spring return
from left
Spring return
two-way
Two standard
keys are
supplied.
When the H2
key handle is
required,
specify H2.
UCSQO (Enclosed Type)
Maintained:
1 to 6 decks
Spring return:
1 to 3 decks
Maintained:
2 to 12 positions
Spring return:
2 to 4 positions
Maintained:
30°, 45°, 60°, 90°
Spring return:
45° only
Spring return
from right
Spring return
from left
Spring return
two-way Y2, S2, F2,
P2
(one speci-
fied handle
supplied)
Type CQ
See
page 56.
UCSQM (Enclosed Type)
Spring return:
1 to 3 decks Spring return:
3 positions Spring return:
45° only Spring return
two-way
C1007
C1008
C1009
C1010
C1018
C2006
C2007
C2021
See
page 51.
Type
CQM
See
page 56.
(Photo: ACSNO with Y2 handle)
Standard Key (2 keys supplied)
H2 Handle Key
58
24
(black)
(Photo: With Y2 handle)
Spring Return 2-way
Left Right
Indicator
Left: Green
Right: Red
M3.5 Terminal
Screw
(P2 Handle)
4-M4 Screw
2912
12N+9
52
770
64
50
Panel Thickness 7.0 max.
31 43
48
N: Number of Contact Blocks
46.4
ACSNO/ACSSO ACSNK/ACSSK
Panel Cut-out
47 47
2912
12N+9
52
52
35
30
M3.5 Terminal Screw Panel Thickness 0.8 to 6
Spring Return: 44
Maintained: 42
N: Number of Contact Blocks
M3.5 Terminal
Screw
(Y2 Handle)
4-M4 Screw
2912
52
12N+9 725 70
64
41
Panel Thickness
7.0 max.
48
46.4
Spring Return: 31
Maintained: 29
N: Number of Contact Blocks
R0.8 max.
ø25.5
(ACSSO/ACSSK)
ø30.5
(ACSNO/ACSNK)
ø5
+0.5
0
0
+0.2
0
+0.5
+0.5
0
4.8
33
4-ø4.5
48
48
ø13
Minimum horizontal/vertical mounting centers
With P2 handle: 125
With other handles: 70
Panel Cut-out
Minimum horizontal/vertical mounting centers
With P2 handle: 125
With other handles: 70
UCSQO UCSQM
All dimensions in mm.
Spring Return: 44
Maintained: 42
N: Number of Contact Blocks
M3.5 Terminal Screw
47 47
52
(S2 Handle)
Panel Thickness 0.8 to 6
29
12
12N+9 30.7
52
50
CS Series Cam Switches
48
ø30/ø25
Ordering Information
When ordering, specify items through as the designation example below.
➀➁➂➃➄➅
Type Contact Block
Decks Positions Angle Spring
Return Handle Circuit No.
➁➂
➅➆
Decks Code Positions Code Angle Code Return Code
ACSNO
ACSNK
ACSSO
ACSSK
UCSQO
UCSQM
1 deck
2 decks
3 decks
4 decks
5 decks
6 decks
1
2
3
4
5
6
2 positions
3 positions
4 positions
5 positions
6 positions
7 positions
8 positions
9 positions
10 positions
11 positions
12 positions
2
3
4
5
6
7
8
9
10
11
12
30°
45°
60°
90°
3
4
6
9
Spring return
from left
Spring return
from right
Spring return
two-way
RO
OR
RR
(Code)
Y2, S2, P2,
F2, H2,
25S2
(Color)
B: Black
See table
below.
For standard contact
arrangements, use des-
ignation code on pages
51 to 53.
For custom contact
arrangements, use the
Custom Contact
Arrangement Specifica-
tion Sheet on page 54.
Spring return:
1 to 3 decks only Spring return:
2 to 4 positions only ACSNK/ACSSK:
45° and 90° only
Spring return:
45° only
Spring return code is
required only for spring
return types.
25S2 is for
ACSSO
only.
Designation Example
1. When a special contact arrangement is required, specify
the contact arrangement using the Custom Contact
Arrangement Specification Sheet on page 54.
2. A specified handle is attached.
3. Accessories such as nameplates and jumpers are sepa-
rately ordered.
4. The key of the key operated cam switch is removable
from every position. Specify other key removable configu-
rations if required.
UCSQO - 2 3 4 RR - S2B - C2006
➁➂➃
Handle Designation Code
Shape Code Color Applicable
Cam Switch
Y2
B: black
ACSNO
UCSQO
UCSQM
S2
25S2 ACSSO
P2
ACSNO
UCSQO
UCSQM
F2
H2 ACSNK
ACSSK
30 22
19
20
ø30 Y Han
d
le
30 20
30
20
ø30 S Handle
25.6 20
30
20
ø25 S Handle
30
50
40
ø30 P Handle
30 ø50
40
ø30 F Handle
18
40
24
Key Handle
Spring Return Operation
Available combinations of operator positions, angles, and return directions are listed in the table below.
Note: Maintained types do not require spring return code .
Positions 2-position 3-position 4-position 3-position
Return Direction
From Left From Right From Left From Right Two-way From Left From Right Two-way
➂ ➃ ➄ Codes 24RO 24OR 34RO 34OR 34RR 44RO 44OR 34RR
Applicable Cam Switches ACSNO, ACSSO, ACSNK, ACSSK, UCSQO UCSQM
Contact Block Decks 1 to 3 decks
2
112
231 2
13
23
1
23
4
13
2
1
4
23
1
CS Series Cam Switches
49
ø30/ø25
Accessories and Replacement Parts
Shape Material Type No. Ordering
Type No. Package
Quantity Remarks
Jumper
Metal
CJ-1 CJ-1PN10 10 For connecting terminals of
adjoining contact blocks
CJ-2 CJ-2PN10 10 For connecting terminals of the
same contact block
Rubber Boot
Rubber CR-1 CR-1 1
For preventing ingress of dust
into the contact blocks
Not applicable for the UCSQO
and UCSQM
Terminal Cover
Plastic
CS-VL2-13S CS-VL2-13S 1 For 1 to 3 decks of contact blocks
CS-VL2-46S CS-VL2-46S 1 For 4 to 6 decks of contact blocks
Shape Material (Color) Type No. Ordering Type No. Package Quantity
ø30 Y Handle
Plastic (Black) CSH-YB CSH-YB 1
ø30 S Handle
Plastic (Black) CSH-SB CSH-SB 1
ø25 S Handle
Plastic (Black) CSH-25SB CSH-25SB 1
ø30 P Handle
Plastic (Black) CSH-PB CSH-PB 1
ø30 F Handle
Plastic (Black) CSH-FB CSH-FB 1
Key Handle
Plastic (Black) CSH-H2B CSH-H2B 1
Handle Shaft
Plastic CS-HF2C CS-HF2CPN05 5
Handle Screw
For Y, ø30 S, and ø25 S handles
M3 × 12 CS-SCW-M3-12 CS-SCW-M3-12PN10 10
Handle Screw
For P and F handles
M3 × 25 CS-SCW-M3-25 CS-SCW-M3-25PN10 10
CJ-1
CJ-2
CS-VL2-13S
Supplied with 2 self-
tapping screws
for mounting
30 22
19
20
30 20
30
20
25.6 20
30
20
30
50
40
30 ø50
40
18
40
24
CS-VL2-46S
CS Series Cam Switches
50
ø30/ø25
Terminal Cover Dimensions
Installing the Terminal Cover for the CS
series Cam Switches
Complete wiring before installing the terminal cov er on the
bottom plate of the contact block.
The terminal cover has six holes. Of the four round holes
at f our corners, use two diagonal pair of holes to install the
terminal cover. Either pair can be used.
Insert the attached self-tapping screws into the pair of
holes and tighten the screws to a torque of 0.8 to 1.0 N·m.
For 1 through 3 decks of contact b locks, use terminal cov er
CS-VL2-13S.
For 4 through 6 decks of contact b locks, use terminal cov er
CS-VL2-46S.
The CS-VL2-46S consists of the CS-VL2-13S and a termi-
nal cover for the fourth through sixth decks. Combine the
two parts together as shown. Note that once combined,
the two parts cannot be separated.
Minimum Mounting Centers for Installing
the Terminal Cover
Although the minimum mounting centers are 100 mm hori-
zontally and 70 mm v ertically, determine the mounting cen-
ters in consideration of convenience of wiring. For the P2
handle, the minimum mounting centers are 125 mm hori-
zontally and vertically.
CS-VL2-13S
Mounting Hole
Mounting Hole
Bottom Plate
Self-tapping Screw (attached)
Insert the screws into
a diagonal pair of holes.
For 1 through 3 decks of contact blocks (CS-VL2-13S)
100 mm min.
(P2 handle: 125 mm)
(P2 handle: 125 mm)
70 mm min.
CS-VL2-13S
For 4 through 6 decks of contact blocks (CS-VL2-46S)
47
91.4 (CS-VL2-13S)
94.4 (CS-VL2-46S) 7.5
12
9
52
2 40.5
(N: Number of Contact Blocks)
66.1 (CS-VL2-46S)
64.6 (CS-VL2-13S)
34.5 (CS-VL2-46S)
33 (CS-VL2-13S)
12N+9
All dimensions in mm.
CS Series Cam Switches
51
ø30/ø25
Standard Contact Arrangement Chart
1 2 9 C1001 1 2 9 C1002 1 2 4 OR C1003 1 2 4 OR C1004 1 3 4 C1005
1 3 4 C1006 1 3 4 RR C1007 1 3 4 RR C1008 1 3 4 RR C1009 1 3 4 RR C1010
1 4 4 C1011 1 2 9 C1013 1 2 9 C1014 1 2 4 OR C1015 1 3 4 C1016
1 2 4 C1017 1 3 4 RR C1018 1 2 6 C1019
2 2 9 C2001 2 2 9 C2002 2 3 4 C2003 2 3 4 C2004 2 3 4 C2005
Standard Contact Arrangements
The f ollowing tab le lists 76 standard contact arrangements
for easy designation of required cam switch operation.
When other contact arrangements are required, specify
the number of contact block decks, operator positions,
angles, and contact operation using the Custom Contact
Arrangement Specification Sheet on page 54.
Listing Order of the Table
The 76 standard contact arrangements are listed in the
order of the circuit number.
Same Circuits
Shown in the following examples , circuits of Fig. 1 and Fig.
2 have the same functions. When ordering, examine the
standard contact arrangements. Your requirements may be
satisfied simply by changing external wiring of the stan-
dard contact arrangments.
Terminal Numbers
The terminal numbers on the contact blocks correspond
with the numbers shown in the chart as shown below.
Symbol Contact Operation
Contacts closed.
Contacts remain closed between two operator posi-
tions.
Overlapping Contacts
Contacts of different decks are both closed at one
point while the handle is turned to the next position.
Residual Contacts
When the handle is returned to the center, the con-
tacts remain closed. The contacts are opened when
the handle is turned to the opposite direction.
2 3 4 RR C2006
7
5
3
1
8
6
4
2
12 3
Circuit No.
No. of Decks: 2
Position: 3-position
Angle: 45°
Spring Return Type:
2-way
Terminal No.
Operator Position
The arrow shows the
spring return direction.
7
3
5
1
7
3
5
1
7
3
5
1
7
3
5
1
8
4
6
2
8
4
6
2
8
4
6
2
8
4
6
2
1 2 3 1 2 3 1 2 3 4 1 2 3 4
Example 1
Fig. 1 Fig. 2 Example 2
Fig. 1 Fig. 2
7
5
3
1
8
6
4
2
1 2 Operator Position
Terminal No.
Terminal No.
3
14
2
1 2
3
14
2
1 2
3
14
2
1 2
1
2
3
1 4
2
3
14
2
123
3
14
2
1 2 3
3
14
2
1 2 3
3
14
2
1 2 3
3
14
2
1 2 3
3
14
2
1 2 3
3
14
2
1 2 3 4
3
14
2
1 2
3
14
2
1 2
3
14
2
1 2
3
14
2
123
3
14
2
1 2
3
14
2
1 2 3
3
14
2
1 2
7
5
3
1
8
6
4
2
1 2
7
5
3
1
8
6
4
2
1 2
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
CS Series Cam Switches
52
ø30/ø25
2 3 4 RR C2006 2 3 4 RR C2007 2 4 4 C2008 2 4 4 C2009 2 4 9 C2011
2 2 9 C2014 2 2 9 C2015 2 3 4 C2016 2 3 4 C2017 2 3 4 C2018
2 3 4 C2019 2 3 4 C2020 2 3 4 RR C2021 2 4 4 C2022 2 3 3 C2023
2 3 3 C2024 2 4 3 C2025 2 5 3 C2027 2 3 6 C2028 2 3 6 C2029
3 2 9 C3001 3 3 4 C3002 3 5 4 C3003 3 6 4 C3004 3 3 4 C3005
3 4 9 C3008 3 4 9 C3009 3 2 9 C3010 3 3 4 C3011 3 4 4 C3012
3 6 3 C3013 3 3 6 C3014 3 6 6 C3015 3 5 3 C3016 3 4 4 C3017
3 3 6 C3018 3 3 6 C3019 4 4 4 C4001 4 8 4 C4002 4 4 9 C4003
4 2 4 C4004 4 2 9 C4005 4 2 9 C4006 4 4 9 C4007 4 3 4 C4008
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1234
7
5
3
1
8
6
4
2
1234
7
5
3
1
8
6
4
2
1234
(O) (R) (S) (T)
7
5
3
1
8
6
4
2
1 2
7
5
3
1
8
6
4
2
12
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1234
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1234
7
5
3
1
8
6
4
2
12345
7
5
3
1
8
6
4
2
1 2 3
7
5
3
1
8
6
4
2
1 2 3
(R) (S) (T)
11
9
7
5
3
1
1 2
12
10
8
6
4
2
11
9
7
5
3
1
1 2 3
12
10
8
6
4
2
11
9
7
5
3
1
12
10
8
6
4
2
12345
11
9
7
5
3
1
123456
12
10
8
6
4
2
11
9
7
5
3
1
1 2 3
12
10
8
6
4
2
11
9
7
5
3
1
1234
12
10
8
6
4
2
(O) (RS) (ST) (TR)
11
9
7
5
3
1
1 2 3 4
12
10
8
6
4
2
11
9
7
5
3
1
1 2
12
10
8
6
4
2
11
9
7
5
3
1
1 2 3
12
10
8
6
4
2
11
9
7
5
3
1
1 2 3 4
12
10
8
6
4
2
11
9
7
5
3
1
12
10
8
6
4
2
123456
11
9
7
5
3
1
1 2 3
12
10
8
6
4
2
11
9
7
5
3
1
12
10
8
6
4
2
123456
11
9
7
5
3
1
12
10
8
6
4
2
12345
11
9
7
5
3
1
12
10
8
6
4
2
1234
11
9
7
5
3
1
12
10
8
6
4
2
123
11
9
7
5
3
1
12
10
8
6
4
2
123
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
1234
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
12345678
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
(O) (R) (S) (T)
1234
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
12
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
12
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
12
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
1234
(O) (R) (S) (T)
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
123
7
5
3
1
8
6
4
2
123
CS Series Cam Switches
53
ø30/ø25
Application Examples (Voltmeter and Ammeter Circuits)
4 5 4 C4009 5 3 4 C5001 6 4 4 C6001 6 12 3 C6002
6 4 9 C6003 6 9 3 C6004 6 6 6 C6005 6 6 4 C6006
1 2 6 C1019 (ammeter switching, 1CT circuit) 2 3 6 C2029 (ammeter switching, 2CT circuit) 2 4 9 C2011 (ammeter switching, 2CT circuit)
2 4 4 C2022 (voltmeter switching, 3PT circuit) 3 3 6 C3019 (ammeter switching, 3CT circuit) 3 4 9 C3008 (voltmeter switching, 2PT circuit)
3 4 9 C3009 (voltmeter switching, 3PT circuit) 4 4 9 C4003 (ammeter switching, 3CT circuit) 4 4 9 C4007 (ammeter switching, 2CT circuit)
6 4 9 C6003 (ammeter switching, 3CT circuit)
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
12345
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
123
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
1234
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
123456789101112
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
1234
(O) (R) (S) (T)
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
1234
43210
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
123456
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
(RS)(ST)(RT)(RE)(SE)(TE)
123456
CT
E
3
14
2
A
CS 7
5
3
1
8
6
4
2
RST
RST
CT
CS A
E
RST
CT
ORST
7
5
3
1
8
6
2
A
CS
E
4
RSTEPT 7
5
3
1
8
6
4
2
3ø-4W
V
CS RST
RST
CT
11
9
7
5
3
1
12
10
8
6
4
2
A
CS
E
O
PT
ST TR
11
9
7
5
3
1
12
10
8
6
4
2
RST CS
RS V
RSTE
PT
11
9
7
5
3
1
12
10
8
6
4
2
V
CS
3ø-4W
RST
CT
ORST
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
A
CS
E
RST
CT
ORST
15
13
11
9
7
5
3
1
16
14
12
10
8
6
4
2
CS
E
A
CT
ORST
23
21
19
17
15
13
11
9
7
5
3
1
24
22
20
18
16
14
12
10
8
6
4
2
RST A
CS
E
CS Series Cam Switches
54
ø30/ø25
Custom Contact Arrangement Specification Sheet
CS Series Cam Switch Custom Contact Arrangement Specification Sheet
Type No.: Quantity:
Deck Terminal No. Contact Arrangement Chart Terminal No.
Deck 6 23 24
21 22
Deck 5 19 20
17 18
Deck 4 15 16
13 14
Deck 3 11 12
9 10
Deck 2 7 8
5 6
Deck 1 3 4
1 2
Angle
Positions 123456789101112
Spring Return
The preceding pages provide 76 standard contact
arrangements. When other contact arrangements are
required, specify the number of contact block decks, oper-
ator positions, angles, and contact operation using the
Custom Contact Arrangement Specification Sheet shown
below.
For available number of contact blocks and operator posi-
tions, see the Ordering Information on page 48.
1. Specify operator positions
Indicate the operator positions starting at the first position.
When spring return operation is required, mark an arrow
between two operator positions to indicate the spring
return direction.
2. Specify contact operation at each operator position
Indicate the required operation of all contacts at each
operator position using the following symbols.
One deck of contact block contains two poles of contacts
and four terminals. When the handle is made to turn 180°
or more, special attention is needed. Since one cam oper-
ates the two poles of contacts on opposite positions, the
same contact operation repeats on the other pole of con-
tacts when the handle is turned 180°. When different con-
tact operation is needed f or handle angles of 180° or more,
use another deck of contact block.
Deck 2 7
5
Deck 1 3
1
Angle
Positions 12345
Spring Return
Symbol Contact Operation
Contacts closed.
Contacts remain closed between two operator posi-
tions.
Overlapping Contacts
Contacts of different decks are both closed at one
point while the handle is turned to the next position.
Overlapping contacts are not available for handle
angles of 30° and 45°.
Residual Contacts
When the handle is returned to the center, the con-
tacts remain closed. The contacts are opened when
the handle is turned to the opposite direction.
T ype Positions Spring Return Decks Angle Handle
ø30 Series Accessories and Replacement Parts
55
ø30
Ordering T erminal Covers
When ordering terminal covers, specify the Type No. and the quantity.
Accessories
N-VL2 N-VL3 N-VL4 APN-PVL APD-PVL Use of termi-
nal covers
increases the
depth by the
dimensions
below.
Pilot Light
APN, APNE, UPQN, UPQNE
Full V oltage
X +5.0 mm
Pilot Light
APD, APDE X +5.2 mm
Pilot Light
APN, APNE, APD, APDE,
UPQN, UPQNE
Transformer
DC-DC Converter X +2.7 mm
Pushbutton
ABN, ABD, AON, AOD, AVN,
ABGD, AJN, ABFD, ATN,
AOFD, UBQN, AVD, UOQN,
AJD, UWQN, AZD, ABBN,
AYD, ABBS (ø25)
Selector Switch
ASN, ASD, ASTN
Selector Pushbutton
ABN, ASBD
1 contact block
X
+0 mm
2 contact blocks X
2 pieces
3 contact blocks X
2 pieces
4 contact blocks X
2 pieces
Illuminated Pushbutton
ALN, ALD, ALNE, ALDE,
AOLN, AOLD, AOLNE,
AOLDE, ALGN, ALGD,
ALGNE, ALGDE, AOLGN,
AOLGDE, ALFN, ALFD,
ALFNE, ALFDE, AOLFN,
AOLFD, AOLFNE, AOLFDE,
AVLN, A VLD, A VLNE, A VLDE,
AJLN, AJLD, AJLNE, AJLDE,
ULQN, UOLQN
Illuminated Selector Switch
ASLN, ASLD
Push-to-Check Pilot Light
APN1∗∗P
Full V oltage X
2 pieces +4.5 mm
Transformer
DC-DC Converter X +1.5 mm
38.4H × 22W 38H × 30.4W
38.4H × 24W
38H × 46W 37H × 44W
Terminal Cover
Terminal Cover
CB
CB
CB
CB
CB CB
CB
CB CB
CB
ø30 Series Control Unit
Terminal Cover
ø30 Series Accessories and Replacement Parts
56
ø30
Specify a legend code in place of in the Ordering Type No.
Nameplates
Type Legend Material Type No. Ordering
Type No. Package
Quantity Dimensions (mm) Applicable Unit
NA
Blank
Aluminium
1.2 mm thick
White letters on
black background
NA-0
NA-0 1
ø30 Control Unit
NA-0PN10 10
With Legend NA-
NA-1
NA-PN10 10
NALO Blank Aluminium
1.2 mm thick
Black NALO
NALO 1
NALOPN10 10
MLO Blank Brass
(chrome-plated)
1.0 mm thick
Matte MLO
MLO 1
ARN/ARNS
Mono-Lever
MLOPN10 10
CQ
Blank
Aluminium
0.5 mm thick
White letters on
black background
CQ-0
CQ-0 1
With adhesive tapes on
the back
UCSQO
Cam Switch
CQ-0PN10 10
With Legend
(Legend
Codes 31
and 53 only) CQ-
CQ-1
CQ-PN10 10
CQM
Blank
Aluminium
0.5 mm thick
White letters on
black background
CQM-0
CQM-0 1
With adhesive tapes on
the back
UCSQM
Cam Switch
CQM-0PN10 10
With Legend
(Legend
Code 31
only) CQM-
CQM-1
CQM-PN10 10
ø30.5
24.5
40
R17.5
29
.
3
4
7
0
ø
30.5
ø
43
Letters should not be
en
g
raved within this lin
e
20
ø13
2-ø3.5
64
40
5
12
2-ø3.5
ø13
64
ø
30.5
40
30
47.5
R17.5
ø30 Series Accessories and Replacement Parts
57
ø30
• Specify a legend code in place of in the Ordering Type No.
Nameplates
Type Legend Material Type No. Ordering
Type No. Package
Quantity Dimensions (mm) Applicable Unit
CQN
Blank
Aluminium
0.5 mm thick
White letters on
black background
CQN-0
CQN-0 1 With adhesive tapes on
the back
ACSNO, ACSNK
Cam Switches
ø30 mm Selector
Switches
CQN-0PN10 10
With Legend
(Legend
Codes 31, 35,
and 53 only) CQN-
CQN-1
CQN-PN10 10
CQS
Blank
Aluminium
0.5 mm thick
White letters on
black background
CQS-0
CQS-0 1 With adhesive tapes on
the back
ACSSO, ACSSK
Cam Switches
ø25 mm Selector
Switches
CQS-0PN10 10
With Legend
(Legend Code
53 only) CQS-
CQS-1
CQS-PN10 10
HNAV
Blank Polyamide
Black letters on
yellow back-
ground
HNAV-0 HNAV-0 1 HN1E ø30 mm
series
Emergency Stop
Switches
EMERGENCY HNAV-27 HNAV-27 1
ø
30.5
64
ø
25.5
64
1.0
1.5
ø60
ø30
Legend “EMERGENCY STOP”
is indicated outside a ø44mm
circle.
L
egen
d
s
Code Legend
0(blank)
1ON
2OFF
3START
4STOP
31 OFF-ON
35 HAND-AUTO
53 HAND-OFF-AUTO
5
18.5
36 22
10
18.5
36 22
Shape and Engraving Area
Standard Large
Type NA Type NALO
Example
The above example is when the letter is 4 mm tall.
Shape Engraving Area Max. No.
of Lines No. of Letters
on 1 Line
Height Width
Standard 5 36 1 14
Large 10 36 2 14
ø30 Series Accessories and Replacement Parts
58
ø30
Accessories
Shape Material Type No. Ordering
Type No. Package
Quantity Dimensions (mm)
Locking Ring Wrench
Rubber OR-12 OR-12 1
Used to tighten the locking ring when installing
the ø30 or ø25 switch onto a panel.
Lamp Holder Tool
Rubber OR-55 OR-55 1
Used to install and remove the LED/incandes-
cent lamps. See page 64.
Contact Rubber Boot
For momentary 1 layer of contact blocks
(2 contact blocks)
Rubber (nitryl)
(black) OC-99 OC-99 1
Rubber boot used to prevent oil and dirt from
entering into the contact block.
Temperature range: -5 to +60ºC
Cannot be used for zinc diecast control units.
Contact Rubber Boot For 1 layer of
contact
blocks
(2 contact
blocks) Rubber
(translucent)
OC-90 OC-90 1
Applicable to AVN3 and AJN3.
Applicable to ø30 diecast zinc pushbuttons and
selector switches.
For 2 layers
of contact
blocks
(4 contact
blocks)
OC-290 OC-290 1
Anti-rotation Ring
Metal OGL-11 OGL-11PN10 10
Used to prevent the operator from turning.
Generally used when using no nameplates on
selector switches and selector pushbuttons.
See page 64.
Rubber Mounting Hole Plug
Rubber
(black) OB-13B OB-13BPN05 5
Plastic Mounting Hole Plug
Plastic
(gray) OBP-11 OBP-11 1
Metallic Mounting Hole Plug
Metal
(diecast)
(zinc-plated) OB-11 OB-11 1
ø37
ø45
ø46
90
ø34
ø30
ø29
ø26
ø22
ø30 Series
ø25 Series
59
14
ø11.6
OR-55
18 42
44
52
(65.4)
38.8
42.8 42.4
ø30.5
ø39
2.8 0.8
ø30
ø34
ø40
55
10
Used to plug unused
ø30mm mounting holes.
Gray also available.
Ordering Type No .:
OB-13PN05
Locking Ring
4
ø36
5
24
M30 P1.5 Screw
Tightening torque: 1.2 N·m.
Degree of protection: IP65
30 5
ø36
Locking Ring
4
M30 P1.5 Screw
Tightening torque: 1.2 N·m.
Degree of protection: IP65
ø30 Series Accessories and Replacement Parts
59
ø30
Accessories
Shape Material Type No. Ordering
Type No. Package
Quantity Dimensions (mm)
Button Cover for
Extended Pushbuttons
Rubber (nitryl)
Color Type
Black OC-11B OC-11B
1
Green OC-11R OC-11R
Red OC-11G OC-11G
Yellow OC-11Y OC-11Y
Pushbutton
Clear Boot For flush
pushbuttons
Rubber
(EPDM)
OC-121 OC-121 1
For extended
pushbuttons OC-122 OC-122 1
Dust-proof Rubber Cov er f or
Jumbo Mushrooms
Rubber
(nitryl)
black OC-4GN OC-4GN 1
Padlock Cover
Polyarylate
(gasket: nitryl
rubber) OL-KL1 OL-KL1 1
Used to protect pushbuttons, illuminated push-
buttons, and selector switches (knob operator).
Metal Protector
Metal
(zinc-plated) OL-C OL-C 1
Used to protect flush pushbuttons from inadvert-
ent operation.
Can be easily attached using the locking ring.
Locking Attachment
Metal
(zinc-plated) OL-H OL-H 1
Used to lock an extended pushbutton in the
depressed position.
Can be easily attached using the locking ring.
M30 P1.5
ø38
ø28
11
19
Metallic bezels cov-
ered with a rubber boot
to enhance waterproof
characteristics.
Button is not included.
Applicable to e xtended
pushbuttons only.
Used to cover and pro-
tect pushbuttons where
units are subject to
water splash. Not suit-
able for outdoor use or
where the units are sub-
ject to oil splash.
A
B
AB
OC-121 37 16
OC-122 37 16
32
ø80
Panel Thickness
1.2 to 5.5
Used for ABN4G
pushbuttons.
Waterproof Rubber
Gasket 0.5t
24
Key Hole ø8
30
70
ø50
ø30.2
93
29.5
30
R66.5
Panel Thickness
0.8 to 3.2
82.5
Mounting Centers
50 min.
ø30.5
16
11.5 1.6
42.5
ø5 hole
Locking Plate
Mounting Plate
30
16.5
9.5
ø30 Series Accessories and Replacement Parts
60
ø30
Maintenance Parts
Shape Specification Type No. Ordering
Type No. Package
Quantity Remarks
Metallic Bezel
Metal
(chrome-plated) OG-11 OG-11PN02 2
Plastic Bezel
Plastic OGP-11OGP-11PN02 2 Specify a color code in place of .
B (black), G (green), R (red), W (white),
Y (yellow)
Clear Plastic Bezel for Flush
Pushbuttons
Clear Plastic
OGP-13 OGP-13PN02 2
Clear plastic bezel and full shroud.
OGP-1411 cannot be used with LED
illumination units and diecast units.
Clear Plastic Bezel for
Extended Pushbuttons
OGP-14 OGP-14PN02 2
Clear Plastic Bezel for
Illuminated Pushbuttons
OGP-1411 OGP-1411 1
Clear Button Cover
Clear Plastic ABN1B-C ABN1B-CPN05 5 Used on flush and extended pushbut-
tons to indicate a mark or a symbol
engraved on the marking plate. The
clear button cover holds the marking
plate. The ø30 series marking chip can
only be used on the ABN1 and AON1.
Specify a color code in place of .
B (blac k), G (green), R (red), W (white),
Y (yellow)
Marking Plate
Plastic TN-0TN-0PN10 10
ø30 Series Accessories and Replacement Parts
61
ø30
Note: Specify a button color code or lens color code in place of or in the Ordering Type No.
Maintenance Parts
Shape Description Mate-
rial Type No. Ordering
Type No. Package
Quantity Color
1NO contact BS010E BS010E 1 Push rod color: Green
1NC contact BS001E BS001E 1 Push rod color: Red
EM contact
(early make) BS010SE BS010SE 1 Push rod color: Black
LB contact
(late break) BS001SE BS001SE 1 Push rod color: White
1NO contact BST010 BST010 1 Push rod
color: Green Applicable Units:
Pushlock Turn Reset
Push Turn Lock
LED Illuminated
Pushbutton
LED Illuminated
Selector Switch
Incandescent Illumi-
nated Selector
Switch
All ø30 Diecast Zinc
Control Units
1NC contact BST001 BST001 1 Push rod
color: Red
EM contact
(early make) BST010S BST010S 1 Push rod
color: Black
LB contact
(late break) BST001S BST001S 1 Push rod
color: White
Lens Used for
APN(E)1
Plastic
APN106LN-APN106LN-PN05 5 A (amber), C (clear), G (green), R (red),
S (blue), W (white), Y (yellow)
Use the white (W) lens for pure white
illumination
Used for
UPQNE4
U(O)LQNB
UPQN406L-UPQN406L-PN05 5
C (clear), G (green), R (red), S (blue)
Use the clear (C) lens for white illumi-
nation.
UPQN406LD-UPQN406LD-PN05 A (amber), Y (yellow)
Use the amber (A) lens for orange
illumination.
Used for
UPQN3B
U(O)LQN
ULQN06L-ULQN06L-PN05 5
C (clear), G (green), R (red), S (blue)
UPQN06LD-UPQN06LD-PN05 A (amber), W (white), Y (yellow)
Use the amber (A) lens for orange
illumination.
Lens Used for
ALN, AOLN
(LED)
Plastic
ALN2L-ALN2L-PN05 5 G (green), R (red), S (blue)
ALN2LD-ALN2LD-PN05 5 A (amber), W (white), Y (yellow)
Use the white (W) lens for pure white
illumination
Used for
ALN, AOLN
(incandescent)
(1W)
ALN06L-ALN06L-PN05 5 C (clear), G (green), R (red), S (blue)
ALN06LD-ALN06LD-PN05 5 A (amber), W (white)
Use the amber (A) lens for orange
illumination.
Used for
ALN, AOLN
(incandescent)
(2W)
ALN08L-ALN08L-PN05 5 C (clear), G (green), R (red), S (blue)
ALN08LD-ALN08LD-PN05 5 A (amber), W (white)
Use the amber (A) lens for orange
illumination.
Button Flush
Plastic
ABN1B-ABN1B-PN05 5 G (green), R (red), Y (yellow)
Above colors are used for ø30 control
units (dark colored operator units).
For black, use black buttons from light
colored operator units.
Extended ABN2B-ABN2B-PN05 5
Mushroom ABN3B-ABN3B-PN02 2
Button Flush ABN1BN-ABN1BN-PN05 5 B (black), G (green), R (red), S (blue),
Y (yellow), W (white)
Above colors are used for ø30 diecast
zinc control units (light colored operator
units).
Extended ABN2BN-ABN2BN-PN05 5
Mushroom ABN3BN-ABN3BN-PN02 2
Button Mushroom
(ABN4)
Plastic
ABN4B-ABN4B-1
B (black), G (green), R (red), Y (yellow)
Mushroom
(ABN4G/
ABN4F) ABN4GB-ABN4GB-1
Square Flush
(UBQN1) UBQN1B-UBQN1B-PN02 2
Square
Extended
(UBQN2) UBQN2B-UBQN2B-PN02 2
C
ontact Block
(BS: Dark gray)
Contact Block
(BST: Light gray)
ø30 Series Accessories and Replacement Parts
62
ø30
Maintenance Parts
Shape Description Material Type No. Ordering Type No. Package
Quantity Remarks
Lens
For ø40 pushlock turn reset
pushbuttons AVLN3L-R AVLN3L-RPN02 2
Marking Plate
For UPQN4 Plastic UPQN406N-W UPQN406N-WPN05 5
ASNKMetal ASN-SK-24401 ASN-SK-24401PN02 2 Applicable to ABN3K,
ABN4K, ABN5
Rubber Washer (3.0mm thick)
Rubber OW-12 OW-12PN10 10
Rubber Washer (1.5mm thick)
Rubber OW-11 OW-11PN10 10
Shroud Half shroud
(for pushbuttons)
Metal
ABN2G ABN2G 1
Full shroud
(for pushbuttons) ABN2F ABN2F 1
Full shroud
(for mushroom
pushbuttons) ABN3G ABN3G 1
Shallow shroud
(for jumbo mush-
rooms) ABN4G ABN4G 1
Deep shroud
(for jumbo mush-
rooms) ABN4F ABN4F 1
Half shroud
(for illuminated
pushbuttons)
ALN1GL ALN1GL 1 For incandescent/LED
illuminated pushbuttons
(E12 base)
ALN2GL ALN2GL 1 For LED illuminated
pushbuttons (BA9S base)
Full shroud
(for illuminated
pushbuttons)
ALN1F ALN1F 1 For incandescent/LED
illuminated pushbuttons
(E12 base)
ALN2FL ALN2FL 1 For LED illuminated push-
buttons (BA9S base)
Transformer 100/110V AC
(for LED/1W incandescent
lamps) TWR-016N TWR-016N 1
Mounting screws are not
included.
200/220V AC
(for LED/1W incandescent
lamps) TWR-026N TWR-026N 1
Spare Key
ø30 Series Accessories and Replacement Parts
63
ø30
LED Lamps
Incandescent Lamps
Transformer
Maintenance Parts
Dimensions Operating
Voltage Current Draw Type No. Ordering
Type No. Illumination
Color Code Package
Quantity Base
AC DC
6V AC/DC ±10% 17 mA
(A, R, W, Y)
8 mA
(G, PW, S)
14 mA
(A, R, W, Y)
5.5 mA
(G, PW, S) LSTD-6LSTD-6Specify a color
code in place of
in the Order-
ing Type No.
A: amber
G: green
PW: pure white
R: red
S: blue
W: white
Y: yellow
1
BA9S/13
LSTD-6PN10 10
12V AC/DC ±10% 11 mA 10 mA LSTD-1LSTD-11
LSTD-1PN10 10
24V AC/DC ±10% 11 mA 10 mA LSTD-2LSTD-21
LSTD-2PN10 10
6V AC/DC ±10% 17 mA
(A, R, W, Y)
8 mA
(G, PW, S)
14 mA
(A, R, W, Y)
5.5 mA
(G, PW, S) LETD-6LETD-6Specify a color
code in place of
in the Order-
ing Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
1
E12/15
LETD-6PN10 10
12V AC/DC ±10% 7 mA 6.5 mA LETD-8LETD-81
LETD-8PN10 10
24V AC/DC ±10% 11 mA 10 mA LETD-2LETD-21
LETD-2PN10 10
Dimensions Rated Operating
Voltage Lamp Ratings Type No. Package
Quantity Life
6V AC/DC 1W (6.3V) LS-6
1
Approx. 1000 hours minimum
(reference value)
12V AC/DC 1W (18V) LS-8
18V AC/DC 1W (24V) LS-2
24V AC/DC 1W (30V) LS-3
6V AC/DC 2W (6.3V) LE-6
1
12V AC/DC 2W (18V) LE-8
18V AC/DC 2W (24V) LE-2
24V AC/DC 2W (30V) LE-3
Separate Mounting Type Primary Voltage Secondary Voltage Type No. Applicable Load
For 1W 100/110V AC
5.5V
TWR516 One full voltage type pilot light or illuminated
switch containing LSTD-6, LETD-6 LED
lamp (6V AC/DC) or LS-6 incandescent
lamp (6.3 V AC/DC, 1W)
200/220V AC TWR526
400/440V AC TWR546
For 2W 100/110V AC
15V
TWR518
One full voltage type pilot light or illuminated
switch containing LE-8 incandescent lamp
(18V AC/DC, 2W)
200/220V AC TWR528
400/440V AC TWR548
Base BA9S/13
20.4
ø10
Base BA9S/13
22.5±1.5
ø11±1
Base E12/15
34±2
ø13±1
Base E12/15
27
ø12
ø30 Series Instructions
64
ø30
Turn off the power to the ø30 series control units before
starting installation, removal, wiring, maintenance, and
inspection of the products. Failure to turn power off may
cause electrical shocks or fire hazard.
To avoid a burn on your hand, use the lamp holder tool
when replacing lamps.
For wiring, use wires of a proper size to meet the voltage
and current requirements. Tighten the M3.5 terminal
screws to a tightening torque of 1.0 to 1.3 N·m. Failure to
tighten terminal screws may cause overheat and fire.
Panel Mounting for Square Pushbuttons
and Pilot Lights
1. Tighten the square ring to the operator and position the
ring correctly.
2. Lightly tighten the screw to secure the pilot light onto the
panel.
Tightening T orque for Terminal Screws
Tighten the terminal screws to a torque of 1.0 to 1.3 N·m.
Replacement of Lamps
Lamps can be replaced by using the lamp holder tool (OR-
55) from the front of the panel.
How to Remove
To remove, slip the lamp holder tool onto the lamp head
lightly. Then push slightly, and turn the lamp holder tool
counterclockwise.
How to Install
To install, insert the lamp head into the lamp holder tool.
Place the pins on the lamp base to the groov es in the lamp
socket. Inset the lamp and turn it clockwise.
Installing the Anti-rotation Ring
Panel Thickness and Rubber Washer
Adjust the thickness of the rubber washers according to the
panel thickness. Also, make sure to include the nameplate
thickness when using a nameplate.
Safety Precautions
Instructions
Recommended tightening
torque: 0.15 N·m
OR-55
Rubber Washer
Panel OGL11
Anti-rotation rings are used
on selector switches or
pushbuttons which rotate
and used when using no
nameplates.
Insert a 1.5mm thick rubber
washer between the panel
and the anti-rotation ring as
shown on the right.
Applicable Models
Extended Illuminated Pushbuttons
with Half Shroud (LED)
Extended Pushbuttons with Half
Shroud (Diecast)
Extended Illuminated Pushbuttons
with Half Shroud (Diecast)
Applicable Models
Extended Illuminated Pushbuttons
with Full Shroud (Incandescent)
Extended Illuminated Pushbuttons
with Full Shroud (LED)
Extended Illuminated Pushbuttons
with Full Shroud (Diecast)
Mushroom Pushbuttons with Full
Shroud
The number in brackets is for mush-
room pushbuttons with full shroud.
Extended illuminated pushbuttons
with full shroud (incandescent) are
5.0 mm maximum.
Applicable Models
Toggle Lever Types
Knob Push Turn Lock Illuminated
Pushbuttons
The number in brackets is for knob
push turn lock illuminated pushbut-
tons.
Panel Thickness
(mm) Rubber W asher
1.5mm 3.0mm
Supplied 1 piece 1 piece
0.8 to 1.8 1 piece
1.8 to 3.5 1 piece
Panel Thickness
(mm) Rubber W asher
1.5mm 3.0mm
Supplied 2 pieces 1 piece
0.8 to 2.0 1 piece 1 piece
2.0 to 3.5 1 piece 1 piece
3.5 to 5.0 1 piece
5.0 to 6.0 (6.5) 1 piece
Panel Thickness
(mm) Rubber W asher
1.5mm 3.0mm
Supplied 1 piece 1 piece
0.8 to 2.0 1 piece 1 piece
2.0 to 3.5 1 piece
3.5 to 5.5 (5.0) 1 piece
Applicable Models
Extended Pushbuttons with Half
Shroud
Extended Illuminated Pushbuttons
with Half Shroud (Incandescent)
Applicable Models
Extended Pushbuttons with Full
Shroud
Applicable Models
Extended Pushbuttons with Full
Shroud (Diecast)
Applicable Models
Other Models (Excluding Square
Types)
Panel
Thickness
(mm)
Rubber W asher
1.5mm 3.0mm
Supplied 1 piece 1 piece
0.8 1 piece 1 piece
0.8 to 2.3 1 piece
2.3 to 4.0 1 piece
Panel
Thickness
(mm)
Rubber W asher
1.5mm 3.0mm
Supplied 3 pieces 1 piece
0.8 to 1.5 3 pieces 1 piece
1.5 to 3.0 2 pieces 1 piece
3.0 to 4.5 1 piece 1 piece
4.5 to 6.0 1 piece
6.0 to 7.5 1 piece
Panel
Thickness
(mm)
Rubber W asher
1.5mm 3.0mm
Supplied 2 pieces 1 piece
0.8 to 2.5 2 pieces 1 piece
2.5 to 4.0 1 pieces 1 piece
4.0 to 5.5 1 piece
5.5 to 6.0 1 piece
Panel
Thickness
(mm)
Rubber W asher
1.5mm 3.0mm
Supplied 2 pieces 1 piece
0.8 to 3.5 2 pieces 1 piece
3.5 to 5.0 1 piece 1 piece
5.0 to 6.5 1 piece
6.5 to 7.5 1 piece
ø30 Series Instructions
65
ø30
Installation of LED Illuminated Units
1. Note the polarity for wiring when connecting to DC-DC
converter unit.
2. Transf ormer type units are recommended for use in areas
subjected to noise.
3. Notes for Pure White LED Lamps
Do not use the pure white LED outdoors, otherwise it will
lead to the degradation of brightness and color. Do not
remove or apply shock to the cap on the pure white LED
lamp, otherwise it may break or damage the cap.
For the pure white LED, use a white lens. The illumination
color will be dull if a different color is used.
Terminal No. Polarity
X1 Positive
X2 Negative
Notes on LED Illuminated Units
LED lamps consist of semiconductors. If the applied v oltage
exceeds the rated voltage, LED elements may deteriorate
due to overheat, resulting in significant decrease in lumi-
nance, hue change, or failure of lighting. Also, if an extrane-
ous noise, transient v oltage, or tr ansient current is applied to
the circuit, similar effects may occur. When using LED
lamps, observe the following instructions.
Rated V oltage
The LED lamps are rated at 6V, 12V, or 24V A C/DC, and can
be used within ±10% the rated voltage of either AC or DC.
DC Power
1. Switching power supply
Regulated voltage from switching power supply is best
suited. Make sure to use within the rated voltage of the
LED lamp.
2. Rechargeable battery
Note that the battery voltage may exceed the rated volt-
age of the LED lamp while the battery is being charged
and immediately after the charging is complete. Be sure
to use the LED lamp on a voltage of ±10% the rated volt-
age.
3. Full-wave rectification
Since the LED lamp is A C/DC compatible , a diode bridge
for rectification is not necessary. If the LED lamp is used
on a full-wa ve rectification current through a diode bridge,
the rectifier diodes will reduce the voltage, resulting in
lower luminance.
4. Single-phase half-wave rectification
This is not suitable for the power source of LED lamps.
Use constant-voltage DC power.
Noise
LED elements deteriorate due to extr aneous noise, resulting
in significant decrease in luminance, hue change, or failure
of lighting. When such effects are anticipated, take a protec-
tion measure shown belo w , such as RC elements or a surge
absorber.
[Protection Example 1] For AC circuit
[Protection Example 2] For DC circuit
Countermeasures against Dim Lighting
1. Leakage currents through the transistors or a contact
protection circuit may cause the LED lamp to illuminate
dimly even when the output is off.
2. When the LED lamp is illuminated by a transistor output,
take the following measure.
[Circuit Example]
Connect shunt resistor R in parallel with the LED lamp.
LED with
transformer LED R
C
LED
Ry
Relay
coil or
solenoid R
C
LED with
transformer
(Reference values) R:120
C: 0.1 µF
Ry LED Diode
Relay
coil or
solenoid
+
(Reference values of the diode)
Forward current: More than the Ry coil current
Reverse withstand voltage: Ry coil current × 10
R
Io
Io: Leakage current when the output is off
R: Shunt resistor
LED
66
ø30 Series Diecast Zinc Control Units
Heavy duty switches for tough industrial usage
Degree of protection: IP65 (IEC 60529)
UL, CSA approved, and EN compliant
Contact Ratings
Characteristics
Contact Ratings by Utilization Category
Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1).
Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types)
BST Contact Block (Light Gray)
Safety Standards File No. or Organization
UL UL Listing
File No. E68961
CSA File No. LR21451
EN EN60947-5-1
Specifications and Ratings
Pushbuttons
Illuminated Pushbuttons
Selector Switches
Illuminated Selector Switches
Selector Pushbuttons
Contact Block Type BST (ø30 series)
Rated Insulation Voltage 600V
Rated Continuous Current 10A
Contact Ratings by Utilization Category
IEC 60947-5-1 AC-15 (A600)
DC-13 (P600)
Operational Voltage 24V 48V 50V 110V 220V 440V
Operational
Current
AC
50/60 Hz AC-12 Control of resistive loads and solid state loads 10A 10A 10A 6A 2A
AC-15 Control of electromagnetic loads (> 72 VA) 10A 7A 5A 3A 1A
DC DC-12 Control of resistive loads and solid state loads 10A 5A 2.2A 1.1A
DC-13 Control of electromagnets 5A 2A 1.1A 0.6A
Specifications, ratings, and mounting hole layouts are the same as ø30 control units.
See “ø30 Series Control Units” on page 7.
Contact Block Types
Contact
Single-pole Contact Block Type
1NO 1NC 1NO (early make) 1NC (late break)
Type BST BST010 BST001 BST010S BST001S
Push Rod Green Red Black White
Note: BST contact blocks are not interchangeable with dark gray BS contact
blocks used for ø30 control units.
Push Rod
M3.5 Terminal Screw
Inspection Window
Interlocking Groove
Mounting Screw
ø30
ø30 Series Diecast Zinc Control Units
67
ø30
The Type No. development charts shown below can be used to specify control units other than those listed on the following
pages.
Ordering Information
Standard Units
Specify an operator or lens color code in the Type No.
Black, green, and red colored buttons are included with
flush pushbuttons.
Full voltage type illuminated units are not supplied with a
lamp. Order LED or incandescent lamps separately.
Transformer type illuminated units contain an LED or
incandescent lamp.
Terminal cov ers, nameplates, and accessories are ordered
separately.
Terminal Cover
When a terminal cover is required, order an applicable
terminal cover referring to page 55.
ø30 Series Diecast Zinc Pushbuttons
ø30 Series Diecast Zinc Pilot Lights
ø30 Series Diecast Zinc Illuminated
Pushbuttons
ABD2 11 N R
Button color code
Contact arrangement code
10: 1NO
01: 1NC
11: 1NO-1NC
20: 2NO
02: 2NC
22: 2NO-2NC
Note:
Mushroom pull type AZD3 can have a maximum of two contact
blocks.
Mushroom push-pull type AYD31 can have a maximum of two
contact blocks.
APDE 1 99 D N R Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Operating voltage code
99: Full voltage
16/18: Transformer (100/110V AC)
116/118: Transformer (115V AC)
126/128: Transformer (120V AC)
26/28: Transformer (200/220V AC)
236/238: Transformer (230V AC)
246/248: Transformer (240V AC)
386/388: Transformer (380V AC)
46/48: Transformer (400/440V AC)
486/488: Transformer (480V AC)
Lamp receptacle:
E: E12 (LETD-6
LED or 2W
incandescent lamps)
(blank): BA9S (LSTD-6
LED or 1W
incandescent lamps)
Note:
Full voltage type is not supplied with a lamp.
Transf ormer types contain an LED lamp (LSTD-6
or LETD-6
)
or incandescent lamp (LS-6, 1W or LE-8, 2W).
LED lamps cannot be used on 480V AC transformers.
Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48,
and 488 are available for incandescent types only.
ALDE 2 16 11 D N R Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Contact arrangement code
11: 1NO-1NC 20: 2NO
02: 2NC 31: 3NO-1NC
22: 2NO-2NC 13: 1NO-3NC
40: 4NO 04: 4NC
Operating voltage code
99: Full voltage
16/18: Transformer (100/110V AC)
116/118: Transformer (115V AC)
126/128: Transformer (120V AC)
26/28: Transformer (200/220V AC)
236/238: Transformer (230V AC)
246/248: Transformer (240V AC)
386/388: Transformer (380V AC)
46/48: Transformer (400/440V AC)
486/488: Transformer (480V AC)
Lamp receptacle
E: E12 (LETD-6 LED or 2W
incandescent lamps)
(blank): BA9S (LSTD-6LED or 1W
incandescent lamps)
Note:
Illuminated pushbuttons cannot have an odd number of contact
blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and
3NC.
Full voltage type is not supplied with a lamp.
Transf ormer types contain an LED lamp (LSTD-6 or LETD-6)
or incandescent lamp (LS-6, 1W or LE-8, 2W).
LED lamps cannot be used on 480V AC transformers.
Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48,
and 488 are available for incandescent types only.
ø30
Series
Diecast Zinc Control Units
68
ø30
ø30 Series Diecast Zinc Selector Switch
ø30 Series Diecast Zinc
Key Selector Switch
ø30 Series Diecast Zinc
Illuminated Selector Switch
ASD 2 L 11 N Contact arrangement code
Operator type
(blank): Knob
L: Lever
Number of positions
ASD 2 K 20 N B Key removable position code
2-position
Maintained
(blank): Removable in all positions
B: Removable in left only
C: Removable in right only
Spring return from right
(blank): Removable in left only
Spring return from left
(blank): Removable in right only
3-position
Maintained
(blank): Removable in all positions
B: Removable in left and center
C: Removable in right and center
D: Removable in center only
E: Removable in right and left
G: Removable in left only
H: Removable in right only
Spring return from right
(blank): Removable in left and center
D: Removable in center only
G: Removable in left only
Spring return from left
(blank): Removable in right and center
D: Removable in center only
H: Removable in right only
Spring return two-way
(blank): Removable in center only
Contact arrangement code
Number of positions
Note:
The key cannot be removed in the return position.
ASLD 2 16 22 D N R Lens color code
Lamp type
D: LED (Transformer type only)
(blank): Incandescent
Contact arrangement code
Operating voltage code
99: Full voltage
16: Transformer (100/110V AC)
156: Transformer (115V AC)
136: Transformer (120V AC)
26: Transformer (200/220V AC)
236: Transformer (230V AC)
256: Transformer (240V AC)
386: Transformer (380V AC)
46: Transformer (400/440V AC)
486: Transformer (480V AC)
Number of positions
Note:
Full voltage type is not supplied with a lamp.
Transf ormer type contains an LED lamp (LSTD-6) or incandes-
cent lamp (LS-6).
LED lamps cannot be used on 480V AC transformers.
ø30 Diecast Zinc
Series
Pushbuttons
69
ø30
Round bezel and shroud (metal): Chrome-plated
Pushbuttons with one or three contact blocks contain a dummy block
Other contact arrangements are also available. See page 67.
Flush / Extended / Extended with Half Shroud / Extended with Full Shroud
Shape Operation
Type Contact Type No.
Button Color
Code Dimensions (mm)
Flush
ABD1
Momentary
1NO ABD110N
Black (B), green
(G), and red (R)
buttons are sup-
plied with each
unit.
Specify S, Y, or
W when a blue,
yellow, or white
button is
required.
1NC ABD101N
1NO-1NC ABD111N
2NO ABD120N
2NC ABD102N
2NO-2NC ABD122N
Flush
AOD1
Maintained
1NO AOD110N
1NC AOD101N
1NO-1NC AOD111N
2NO AOD120N
2NC AOD102N
2NO-2NC AOD122N
Extended
ABD2
Momentary
1NO ABD210N
Specify a button
color code in
place of
in the
Type No.
B: black
G: green
R: red
S: blue
W: white
Y: yellow
1NC ABD201N
1NO-1NC ABD211N
2NO ABD220N
2NC ABD202N
2NO-2NC ABD222N
Extended
AOD2
Maintained
1NO AOD210N
1NC AOD201N
1NO-1NC AOD211N
2NO AOD220N
2NC AOD202N
2NO-2NC AOD222N
Extended with Half Shroud
ABGD2
Momentary
1NO ABGD210N
1NC ABGD201N
1NO-1NC ABGD211N
2NO ABGD220N
2NC ABGD202N
2NO-2NC ABGD222N
Extended with Half Shroud
AOGD2
Maintained
1NO AOGD210N
1NC AOGD201N
1NO-1NC AOGD211N
2NO AOGD220N
2NC AOGD202N
2NO-2NC AOGD222N
Extended with Full Shroud
ABFD2
Momentary
1NO ABFD210N
1NC ABFD201N
1NO-1NC ABFD211N
2NO ABFD220N
2NC ABFD202N
2NO-2NC ABFD222N
Extended with Full Shroud
AOFD2
Maintained
1NO AOFD210N
1NC AOFD201N
1NO-1NC AOFD211N
2NO AOFD220N
2NC AOFD202N
2NO-2NC AOFD222N
M3.5 Terminal Screw
623
9
Panel Thickness 0.8 to 7.5
ø35
36
40
68 (1 to 2 blocks)
91 (3 to 4 blocks)
5.5 23 9
Panel Thickness 0.8 to 7.5
ø35
40
ø25
ø40
14.5
53 (1 or 2
blocks)
76 (3 or 4 blocks)
M3.5 Terminal Screw
5.5 23
ø35
40
ø25
ø40
Panel Thickness 0.8 to 3.5
49.5 (1 or
2 blocks)
72.5 (3 or 4 blocks)20.5
ø27
M3.5 Terminal Screw
5.5 23 40
ø40
51.5 (1 or
2 blocks)
74.5 (3 or 4 blocks)
ø35
ø25
ø28.5
17
Panel Thickness 0.8 to 6
M3.5 Terminal Screw
ø30 Diecast Zinc Series Pushbuttons
70
ø30
Specify a button color code in place of in the Type No.
Round bezel and shroud (metal): Chrome-plated
Pushbuttons with one or three contact blocks contain a dummy block
Other contact arrangements are also available. See page 67.
Mushroom / Jumbo Mushroom Types
Shape Operation
Type Contact Type No. Button Color
Code Dimensions (mm)
Momentary
1NO ABD310N
B: black
G: green
R: red
W: white
Y: yellow
1NC ABD301N
1NO-1NC ABD311N
2NO ABD320N
2NC ABD302N
2NO-2NC ABD322N
Maintained
1NO AOD310N
1NC AOD301N
1NO-1NC AOD311N
2NO AOD320N
2NC AOD302N
2NO-2NC AOD322N
Momentary
1NO ABGD310N
1NC ABGD301N
1NO-1NC ABGD311N
2NO ABGD320N
2NC ABGD302N
2NO-2NC ABGD322N
Maintained
1NO AOGD310N
1NC AOGD301N
1NO-1NC AOGD311N
2NO AOGD320N
2NC AOGD302N
2NO-2NC AOGD322N
Momentary
1NO ABD410N
B: black
DG: dark green
DR: dark red
G: green
R: red
Y: yellow
1NC ABD401N
1NO-1NC ABD411N
2NO ABD420N
2NC ABD402N
2NO-2NC ABD422N
Momentary
1NO ABGD410N
1NC ABGD401N
1NO-1NC ABGD411N
2NO ABGD420N
2NC ABGD402N
2NO-2NC ABGD422N
Momentary
1NO ABFD410N
1NC ABFD401N
1NO-1NC ABFD411N
2NO ABFD420N
2NC ABFD402N
2NO-2NC ABFD422N
Mushroom
ABD3
M3.5 Terminal Screw
5.5 23 40
ø40
53 (1 or 2
blocks)
76 (3 or 4 blocks)22
ø40
Panel Thickness 0.8 to 7.5
Mushroom
AOD3
Mushroom with Full Shroud
ABGD3
5.5 23
23
ø48
52 (1 or
2 blocks)
75 (3 or 4 blocks)
Panel Thickness 0.8 to 6.5
M3.5 Terminal Screw
Mushroom with Full Shroud
AOGD3
Jum
b
o Mus
h
room
ABD4
5.5 23
53 (1 or
2 blocks)
76 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
29
ø65
M3.5 Terminal Screw
Jum
b
o Mus
h
room wit
h
ABGD4
Shallow Shroud
5.5 23
53 (1 or
2 blocks)
76 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
ø75
ø65
29
M3.5 Terminal Screw
Jumbo Mushroom with
ABFD4
Deep Shroud
5.5 23
53 (1 or
2 blocks)
76 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
32.5
ø75
M3.5 Terminal Screw
ø30 Diecast Zinc Series Pushbuttons
71
ø30
Pushlock Turn Reset / Push Turn Lock / Pull / Push-Pull / Pin Lock Types
Shape Contact Type No. Button Color
Code Dimensions (mm)
Mushroom Pushlock Turn Reset
AVD3 1NO AVD310N
R: red
Y: yellow
1NC AVD301N
1NO-1NC AVD311N
2NO AVD320N
2NC AVD302N
2NO-2NC AVD322N
1NO AJD310N
B: black
G: green
R: red
Y: yellow
1NC AJD301N
1NO-1NC AJD311N
2NO AJD320N
2NC AJD302N
2NO-2NC AJD322N
1NO AZN310N
B: black
G: green
R: red
S: blue
Y: yellow
1NO-1NC AZN311N
2NO AZN320N
2NC AZN302N
1NO-1NC AYD3111N
2NO AYD3120N
2NC AYD3102N
1NO ABD8P10N
1NC ABD8P01N
1NO-1NC ABD8P11N
2NO ABD8P20N
2NC ABD8P02N
2NO-2NC ABD8P22N
M3.5 Terminal Screw
40
53 (1 or 2
blocks)
76 (3 or 4 blocks)
ø40
Panel Thickness 0.8 to 7.5
24
36
5.5 23
Mushroom Push Turn Lock
AJD3
M3.5 Terminal Screw
K
P
U
S
H
L
O
C
40
53 (1 or 2
blocks)
76 (3 or 4 blocks)
ø40
Panel Thickness 0.8 to 7.5
24
36
5.5 23
Mushroom Pull
AZD3
40
53 (1 or 2 blocks)
ø40
Panel Thickness 0.8 to 7.5
36
5.5 23 30.5
M3.5 Terminal Screw
Mushroom Push-Pull
AYD31
Pin Lock
ABD8P
40
49
Panel Thickness
0.8 to 7.5
ø28
ø35
ø40
52
76 (3 or 4 blocks)28.5
53 (1 or
2 blocks)
5.5 23
M3.5 Terminal Screw
Specify a button color code in place of in the Type No.
Round bezel (metal): Chrome-plated
Pushbuttons with one or three contact blocks contain a dummy
block.
Other contact arrangements are also available. See page 67.
Pushlock T urn Reset: Button is maintained when pressed and is
reset when turned clockwise. Red buttons only.
Note: AVD3 pushlock turn reset switches cannot be used as emer-
gency stop switches. When emergency stop switches are
required, use the HN1E series emergency stop switches
(ISO 13850 and IEC 60947-5-5 compliant).
Push T urn Lock: Button is locked when turned clockwise in the
depressed position and is reset when turned counterclockwise.
Pull: Pulling the button operates the contacts. Up to 2 contact
blocks (1 layer) can be mounted on pull switches.
Push-Pull: Button is maintained in both depressed and reset
positions. Up to 2 contact blocks (1 layer) can be mounted on
AYD31 push-pull switches.
Pin Lock: Button can be loc ked in either depressed or reset posi-
tion by inserting the pin. Pad lock with a ø5mm pin can also be
used to lock the button.
Pull Switch (Spring Return)
Contact AZD3
Normal Pull
1NO
1NC
1NO-1NC
2NO
2NC
Push-Pull Switch (Maintained)
Contact AYD31
Push Pull
1NO-1NC
2NO
2NC
Contact Operation
Note: Pull and push-pull switches can have a maximum of two
contact blocks.
ø30 Diecast Zinc Series Pilot Lights
72
ø30
Operating V oltage Code
Specify an operating voltage code in place of in the Type No.
Specify a lens/LED color code in place of in the Type No. Use the white lens (W) for LED pure white illumination.
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC).
Dimensions
Dome Types
Shape Lamp Input Type Lamp
Receptacle Type No. Lens/LED
Color Code Applicable
Lamp
Dome
APD1
APDE1
Without Lamp Full Voltage
BA9S APD199NA: amber
C: clear
G: green
R: red
S: blue
W: white
Y: yellow
LSTD
LS (1W)
E12 APDE199NLETD
LE (2W)
LED Transformer
BA9S APD1DNA: amber
G: green
PW: pure white
(BA9S only)
R: red
S: blue
W: white
Y: yellow
LSTD-6
E12 APDE1DNLETD-6
Incandescent Transformer
BA9S APD1NA: amber
C: clear
G: green
R: red
S: blue
W: white
LS-6 (1W)
E12 APD1NLE-8 (2W)
Operating V oltage Code
LED Transformer BA9S and E12 Types
Incandescent T ransformer BA9S Type Incandescent T ransformer E12 T ype
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
Full Voltage Type
Transformer Type
M3.5 Terminal Screw
29.5 9
21 40
ø25
ø35
ø40
Panel Thickness 0.8 to 7.5
M3.5 Terminal Screw
9
64.5 21 40
ø25
ø35
ø40
Panel Thickness 0.8 to 7.5
All dimensions in mm.
ø30 Diecast Zinc Series Illuminated Pushbuttons
73
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W).
Dimensions
Round Extended Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact Type No. Applicable
Lamp
Round Extended
ALD2
AOLD2
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALD29911NLSTD
LS (1W)
2NO ALD29920N
2NC ALD29902N
LED Transformer 1NO-1NC ALD211DNLSTD-62NO ALD220DN
2NC ALD202DN
Incandescent Transformer 1NO-1NC ALD211NLS-62NO ALD220N
2NC ALD202N
Maintained
Without Lamp Full Voltage 1NO-1NC AOLD29911NLSTD
LS (1W)
2NO AOLD29920N
2NC AOLD29902N
LED Transformer 1NO-1NC AOLD211DNLSTD-62NO AOLD220DN
2NC AOLD202DN
Incandescent Transformer 1NO-1NC AOLD211NLS-62NO AOLD220N
2NC AOLD202N
Lens/LED Color Code Lens Color Code Operating V oltage Code
LED Illuminated Type Incandescent Illuminated Type
Specify a lens/LED color code in place of
in the Type No.
A: amber
G: green
PW: pure white
R: red
S: blue
W: white
Y: yellow
Use the white lens (W) for LED pure white
illumination.
Specify a lens color code in place of in
the Type No.
A: amber
C: clear
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in
the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
M3.5 Terminal Screw
ø24
ø35
9
97.5 (2 blocks)
120.5 (4 blocks) 24
Panel Thickness 0.8 to 7.5
40
ø40
63 (2 blocks)
M3 Terminal Screw M3 Terminal Screw
ø24
ø35
23
86 (4 blocks)
924
5.5
Panel Thickness 0.8 to 7.5
M3.5 Terminal Screw
40
ø40
ALD2/AOLD2
Full V oltage ALD2/AOLD2
BA9S/Transformer
All dimensions in mm.
ø30 Diecast Zinc Series Illuminated Pushbuttons
74
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W)
Dimensions
Round Extended with Full Shroud Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact Type No. Applicable
Lamp
Round Extended
with Full Shroud
ALFD2
AOLFD2
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALFD29911NLSTD
LS (1W)
2NO ALFD29920N
2NC ALFD29902N
LED Transformer 1NO-1NC ALFD211DNLSTD-62NO ALFD220DN
2NC ALFD202DN
Incandescent Transformer 1NO-1NC ALFD211NLS-62NO ALFD220N
2NC ALFD202N
Maintained
Without Lamp Full Voltage 1NO-1NC AOLFD29911NLSTD
LS (1W)
2NO AOLFD29920N
2NC AOLFD29902N
LED Transformer 1NO-1NC AOLFD211DNLSTD-62NO AOLFD220DN
2NC AOLFD202DN
Incandescent Transformer 1NO-1NC AOLFD211NLS-62NO AOLFD220N
2NC AOLFD202N
Lens/LED Color Code Lens Color Code Operating V oltage Code
LED Illuminated Type Incandescent Illuminated Type
Specify a lens/LED color code in place of
in the Type No.
A: amber
G: green
PW: pure white
R: red
S: blue
W: white
Y: yellow
Use the white lens (W) for LED pure white
illumination.
Specify a lens color code in place of in
the Type No.
A: amber
C: clear
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in
the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
M3.5 Terminal Screw M3 Terminal Screw
235.5
Panel Thickness 0.8 to 6
40
ø40
ø35
ø30
62 (2 blocks)
84 (4 blocks) 25
M3.5 Terminal Screw M3 Terminal Screw Panel Thickness 0.8 to 6
40
ø40
ø35
ø30
96.5 (2 blocks) 25
119.5 (4 blocks)
All dimensions in mm.
ALFD2/AOLFD2
Transformer
ALFD2/AOLFD2
Full V oltage
ø30 Diecast Zinc Series Illuminated Pushbuttons
75
ø30
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Dimensions
Mushroom (ø40) Illuminated Pushbuttons
Shape Lamp
Receptacle Operation
Type Lamp Input Type Contact Type No. Applicable
Lamp
ø40 Mushroom
ALD3
AOLD3
BA9S
Momentary
Without Lamp Full Voltage 1NO-1NC ALD39911DNLSTD2NO ALD39920DN
2NC ALD39902DN
LED Transformer 1NO-1NC ALD311DNLSTD-62NO ALD320DN
2NC ALD302DN
Maintained
Without Lamp Full Voltage 1NO-1NC AOLD39911DNLSTD2NO AOLD39920DN
2NC AOLD39902DN
LED Transformer 1NO-1NC AOLD311DNLSTD-62NO AOLD320DN
2NC AOLD302DN
Lens/LED Color Code Operating V oltage Code
LED Illuminated Type LED T ransformer BA9S Type
Specify a lens/LED color code in place of in the Type No.
A: amber
G: green
R: red
W: white
Y: yellow
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
M3.5 Terminal Screw
M3 Terminal
Screw
23
86 (4 blocks)
5.5
Panel Thickness 0.8 to 7.5
ø40
24
63 (2 blocks)
M3.5 Terminal Screw
M3 Terminal Screw
97.5 (2 blocks)
120.5 (4 blocks)
Panel Thickness 0.8 to 7.5
ø40
24 40
36
40
36
ALD3/AOLD3
Full V oltage ALD3/AOLD3
Transformer
All dimensions in mm.
ø30 Diecast Zinc Series Illuminated Pushbuttons
76
ø30
Operating Voltage Code
Color code: R (red)
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W)
Pushlock T urn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only.
Note: AVLD3 and AVLDE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are
required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant).
Dimensions
Mushroom Pushlock Turn Reset Types
Shape Lamp
Receptacle Lamp Input Type Contact Type No. Applicable
Lamp
Mushroom Pushlock Turn
Reset
AVLD3
AVLDE3
BA9S
Without Lamp Full Voltage 1NO-1NC AVLD39911NR LSTD
LS (1W)
2NO AVLD39920NR
2NC AVLD39902NR
LED Transformer 1NO-1NC AVLD311DNR LSTD-62NO AVLD320DNR
2NC AVLD302DNR
Incandescent Transformer 1NO-1NC AVLD311NR LS-62NO AVLD320NR
2NC AVLD302NR
E12
Without Lamp Full Voltage 1NO-1NC AVLDE39911NR LETD
LE (2W)
2NO AVLDE39920NR
2NC AVLDE39902NR
LED Transformer 1NO-1NC AVLDE311DNR LETD-62NO AVLDE320DNR
2NC AVLDE302DNR
Incandescent Transformer 1NO-1NC AVLD311NR LE-82NO AVLD320NR
2NC AVLD302NR
Operating V oltage Code
LED Transformer BA9S and E12 Types
Incandescent T ransformer BA9S Type Incandescent Transformer E12 Type
16: 100/110V AC
116: 115V AC
126: 120V AC
26: 200/220V AC
236: 230V AC
246: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
18: 100/110V AC
118: 115V AC
128: 120V AC
28: 200/220V AC
238: 230V AC
248: 240V AC
388: 380V AC
48: 400/440V AC
488: 480V AC
M3.5 Terminal Screw
M3 Terminal Screw
M3.5 Terminal Screw
M3 Terminal Screw
23
97.5 (2 blocks)
120.5 (4 blocks)
5.5
Panel Thickness 0.8 to 7.5
ø40
24
Panel Thickness 0.8 to 7.5
112 (2 blocks)
135 (4 blocks)20
ø40
M3.5 Terminal Screw
M3 Terminal Screw
M3.5 Terminal Screw
M3 Terminal Screw
23
86 (4 blocks)
5.5
Panel Thickness 0.8 to 7.5
ø40
24
63 (2 blocks)
Panel Thickness 0.8 to 7.5
5.5 23
20
ø40
77.5 (2 blocks)40
36
100.5 (4 blocks)
40
36
40
36
40
36
AVLD3
BA9S/Full V oltage AVLD3
BA9S/Transformer
AVLDE3
E12/Full V oltage AVLD3/AVLDE3
E12/Transformer
All dimensions in mm.
ø30 Diecast Zinc Series Selector Switches
77
ø30
Knob: Black
Round bezel (metal): Chrome-plated
Selector switches with one contact block contain a dummy block.
On the 2-position selector switches marked with above, the contact operation is reversed as follows.
ASD Selector Switches (Knob Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
ASD
90° 2-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASD210N ASD2110N ASD2210N
2Dummy
11
(1NO-1NC) 1NO ASD211N ASD2111N ASD2211N
2NC
20
(2NO) 1NO ASD220N ASD2120N ASD2220N
2NO
22
(2NO-2NC)
1NO ASD222N ASD2122N ASD2222N
2NC
3NO
4NC
45° 3-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left Spring Return
Two-way
Mounting
Position Type LCR
20
(2NO) 1NO ASD320N ASD3120N ASD3220N ASD3320N
2NO
40
(4NO)
1NO ASD340N ASD3140N ASD3240N ASD3340N
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASD322N ASD3122N ASD3222N ASD3322N
2NO
3NC
4NC
02
(2NC) 1NC ASD302N ASD3102N ASD3202N ASD3302N
2NC
04
(4NC)
1NC ASD304N ASD3104N ASD3204N ASD3304N
2NC
3NC
4NC
L R LR
L R
C
L R C
LR
C
LR
C
LR
[Example]
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
2
4
1
3
M3.5 Terminal Screw
40
5.5 23
ø35
53 (1 or 2
blocks)
76 (3 or 4 blocks) 21
ø40
90°
45°
45°
Panel Thickness 0.8 to 7.5
All dimensions in mm.
ø30 Diecast Zinc Series Selector Switches
78
ø30
Lever: Black
Round bezel (metal): Chrome-plated
Selector switches with one contact block contain a dummy block.
On the 2-position selector switches marked with above, the contact operation is reversed as follows.
ASD Selector Switches (Lever Operator Type)
No. of Positions
Shape
Contact Arrangement Chart
ASDL
90° 2-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASD2L10N ASD21L10N ASD22L10N
2Dummy
11
(1NO-1NC) 1NO ASD2L11N ASD21L11N ASD22L11N
2NC
20
(2NO) 1NO ASD2L20N ASD21L20N ASD22L20N
2NO
22
(2NO-2NC)
1NO ASD2L22N ASD21L22N ASD22L22N
2NC
3NO
4NC
45° 3-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left Spring Return
Two-way
Mounting
Position Type LCR
20
(2NO) 1NO ASD3L20N ASD31L20N ASD32L20N ASD33L20N
2NO
40
(4NO)
1NO ASD3L40N ASD31L40N ASD32L40N ASD33L40N
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASD3L22N ASD31L22N ASD32L22N ASD33L22N
2NO
3NC
4NC
02
(2NC) 1NC ASD3L02N ASD31L02N ASD32L02N ASD33L02N
2NC
04
(4NC)
1NC ASD3L04N ASD31L04N ASD32L04N ASD33L04N
2NC
3NC
4NC
L R LR
L R
C
L R C
LR
C
LR
C
LR
[Example]
M3.5 Terminal Screw
40
5.5 23
ø35
53 (1 or 2
blocks)
76 (3 or 4 blocks)21.5
ø40
90°
45°
45°
Panel Thickness 0.8 to 7.5
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
2
4
1
3
All dimensions in mm.
ø30 Diecast Zinc Series Selector Switches
79
ø30
Cylinder: Black
Round bezel (metal): Chrome-plated
On the spring-returned types, the keys can be released only from the maintained positions. On the maintained types, the key can be
released from every position. Key retained positions are also available. See page 12.
Key selector switches are supplied with two standard keys.
Key selector switches with one contact block contain a dummy block.
On the 2-position selector switches marked with above, the contact operation is reversed as follows.
ASD Key Selector Switches
No. of Positions
Shape
Contact Arrangement Chart
ASDK
90° 2-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left
Mounting
Position Type LR
10
(1NO) 1NO ASD2K10N ASD21K10N ASD22K10N
2Dummy
11
(1NO-1NC) 1NO ASD2K11N ASD21K11N ASD22K11N
2NC
20
(2NO) 1NO ASD2K20N ASD21K20N ASD22K20N
2NO
22
(2NO-2NC)
1NO ASD2K22N ASD21K22N ASD22K22N
2NC
3NO
4NC
45° 3-position
Contact
Code
(ASD)
Contact Block Operator Position Maintained Spring Return
from Right Spring Return
from Left Spring Return
Two-way
Mounting
Position Type LCR
20
(2NO) 1NO ASD3K20N ASD31K20N ASD32K20N ASD33K20N
2NO
40
(4NO)
1NO ASD3K40N ASD31K40N ASD32K40N ASD33K40N
2NO
3NO
4NO
22
(2NO-2NC)
1NO ASD3K22N ASD31K22N ASD32K22N ASD33K22N
2NO
3NC
4NC
02
(2NC) 1NC ASD3K02N ASD31K02N ASD32K02N ASD33K02N
2NC
04
(4NC)
1NC ASD3K04N ASD31K04N ASD32K04N ASD33K04N
2NC
3NC
4NC
L R LR
L R
C
L R C
LR
C
LR
C
LR
[Example]
M3.5 Terminal Screw
40
5.5 23
ø35
53 (1 or 2
blocks)
76 (3 or 4 blocks)
ø40
9
16.538
90°
45°
45°
Panel Thickness 0.8 to 7.5
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
Contact Block Mounting Position and
Contact Arrangement Chart Dimensions
2
4
1
3
All dimensions in mm.
ø30 Diecast Zinc Series Illuminated Selector Pushbuttons
80
ø30
90° 2-position
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC).
On the 2-position selector switches marked with above, the contact operation is reversed as follows.
Illuminated Selector Switches
Shape
Contact Arrangement Chart
Contact
Code
Contact
Block Operator
Position Lamp Input Type
Maintained Spring Return
from Right Spring Return
from Left
Mounting
Position Type LR
11
(1NO-1NC)
1NO Without Lamp Full Voltage ASLD29911NASLD219911NASLD229911N
2NC LED Transformer ASLD211DNASLD2111DNASLD2211DN
Incandescent Transformer ASLD211NASLD2111NASLD2211N
20
(2NO)
1NO Without Lamp Full Voltage ASLD29920NASLD219920NASLD229920N
2NO LED Transformer ASLD220DNASLD2120DNASLD2220DN
Incandescent Transformer ASLD220NASLD2120NASLD2220N
22
(2NO-2NC)
1NO Without Lamp Full Voltage ASLD29922NASLD219922NASLD229922N
2NC
3NO LED Transformer ASLD222DNASLD2122DNASLD2222DN
4NC
Incandescent Transformer ASLD222NASLD2122NASLD2222N
LED Illuminated Type Incandescent Illuminated Type Operating V oltage Code
Lens/LED Color Code Lens Color Code
Specify a lens/LED color code in
place of in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
Specify a lens color code in place of
in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
156: 115V AC
136: 120V AC
26: 200/220V AC
236: 230V AC
256: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
ASLD (Base BA9S)
L R
L R
L R
[Example]
1
2
3
4
40
ø40
235.5
28
9
ø35
ø25
M3.5 Terminal Screws
M3 Terminal Screw
63 (2 blocks)
A: 86 (4 blocks)
B: 97.5 (2 blocks), 120.5 (4 blocks)
Panel Thickness
0.8 to 7.5
(including nameplate)
90°
45°
45°
Contact Block Mounting Position
and Contact Arrangement Chart Dimensions
All dimensions in mm.
LR
1NO
2NC
3NO
4NC
RightLeft
Operator
Position
A: Full voltage type
B: Transformer type
ø30 Diecast Zinc Series Illuminated Selector Pushbuttons
81
ø30
45° 3-position
Color Code and Operating Voltage Code
Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63.
LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC).
Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC).
Illuminated Selector Switches
Contact
Code
Contact
Block Operator
Position Lamp
Input Type
Maintained Spring Return
from Right Spring Return
from left Spring Return
Two-way
Mounting
Position Type LCR
20
(2NO)
1NO Without Lamp
Full V oltage ASLD39920NASLD319920NASLD329920NASLD339920N
2NO LED
Transformer ASLD320DNASLD3120DNASLD3220DNASLD3320DN
Incandescent
Transformer ASLD320NASLD3120NASLD3220NASLD3320N
02
(2NC)
1NC Without Lamp
Full V oltage ASLD39902NASLD319902NASLD329902NASLD339902N
2NC LED
Transformer ASLD302DNASLD3102DNASLD3202DNASLD3302DN
Incandescent
Transformer ASLD302NASLD3102NASLD3202NASLD3302N
22
(2NO-2NC)
1NO Without Lamp
Full V oltage ASLD39922NASLD319922NASLD329922NASLD339922N
2NO
3NC LED
Transformer ASLD322DNASLD3122DNASLD3222DNASLD3322DN
4NC Incandescent
Transformer ASLD322NASLD3122NASLD3222NASLD3322N
40
(4NO)
1NO Without Lamp
Full V oltage ASLD39940NASLD319940NASLD329940NASLD339940N
2NO
3NO LED
Transformer ASLD340DNASLD3140DNASLD3240DNASLD3340DN
4NO Incandescent
Transformer ASLD340NASLD3140NASLD3240NASLD3340N
04
(4NC)
1NC Without Lamp
Full V oltage ASLD39904NASLD319904NASLD329904NASLD339904N
2NC
3NC LED
Transformer ASLD304DNASLD3104DNASLD3204DNASLD3304DN
4NC Incandescent
Transformer ASLD304NASLD3104NASLD3204NASLD3304N
LED Illuminated Type Incandescent Illuminated Type Operating V oltage Code
Lens/LED Color Code Lens Color Code
Specify a lens/LED color code in
place of in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Y: yellow
Specify a lens color code in place of
in the Type No.
A: amber
G: green
R: red
S: blue
W: white
Specify an operating voltage code in place of in the Type No.
16: 100/110V AC
156: 115V AC
136: 120V AC
26: 200/220V AC
236: 230V AC
256: 240V AC
386: 380V AC
46: 400/440V AC
486: 480V AC (incandescent only)
C
LRC
LR
C
LR
C
LR
40
ø40
235.5
28
9
ø35
ø25
M3.5 Terminal Screws
M3 Terminal Screw
63 (2 blocks)
A: 86 (4 blocks)
B: 97.5 (2 blocks), 120.5 (4 blocks)
Panel Thickness
0.8 to 7.5
(including nameplate)
90°
45°
45°
Contact Block Mounting Position
and Contact Arrangement Chart Dimensions
LCR
1NO
2NO
3NC
4NC
Center RightLeft
Operator
Position
All dimensions in mm.
1
2
3
4
A: Full voltage type
B: Transformer type
ø30 Diecast Zinc Series Selector Pushbutton Switches
82
ø30
Specify a button color code in place of in the Type No.
Ring/Lever (Metal): Chrome-plated
Notes :
1. Circuit Code G: The pushbutton does not operate when the ring or lever operator is turned to the right position.
2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever
operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button.
3. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure
may be caused.
4. When installing the lever operator, make sure that the lever is not in the horizontal position. Otherwise, shock resistance may be degraded.
Contact Block Mounting Position and Contact Arrangement Chart
Ring Operator Type / Lever Operator Type Selector Pushbuttons
Shape Contact
Code Circuit
Code
Contact
Block
Ring/Lever
Ring Operator Lever Operator Color
Pushbutton Type No. Type No.
Mounting
Position Type Normal Push Normal Push
Ring Operator
(90˚ 2-Position)
ASBD2
Lever Operator
(90˚ 2-Position)
ASBD2L
11
(1NO-1NC)
A03 1NO ASBD211N-A03ASBD2L11N-A03
B: black
G:green
R: red
Y: yellow
2NC
G03 1NO Blocked ASBD211N-G03ASBD2L11N-G03
2NC
22
(2NO-2NC)
A08
1NO
ASBD222N-A08ASBD2L22N-A08
2NC
3NO
4NC
C10
1NO
ASBD222N-C10ASBD2L22N-C10
2NO
3NC
4NC
D10
1NO
ASBD222N-D10ASBD2L22N-D10
2NO
3NC
4NC
E10
1NO
ASBD222N-E10ASBD2L22N-E10
2NO
3NC
4NC
F10
1NO
ASBD222N-F10ASBD2L22N-F10
2NO
3NC
4NC
G10
1NO
Blocked ASBD222N-G10ASBD2L22N-G10
2NO
3NC
4NC
M3.5 Terminal Screw
40
5.5 23
53 (2 blocks)
76 (4 blocks)
Panel Thickness 0.8 to 7.5
(including nameplate)
ø40
ø28
ø35
25
M3.5 Terminal Screw
M3 Setscrew
(The actual screw is
located on the opposite side)
5.5 23
53 (1 or
2 blocks)
76 (3 or 4 blocks)
Panel Thickness 0.8 to 7.5
(including nameplate)
ø34
50 20
37 37
R50
26.5
Normal Push
1
2
3
4
1
3
2
4
Dimensions
Ring Operator
(90˚ 2-position)
ASBD2
Lever Operator
(90˚ 2-position)
ASBD2L
ø30 Diecast Zinc Series Accessories and Replacement Parts
83
ø30
Turn off the pow er to the ø30 diecast zinc control units before starting installation, removal, wiring, maintenance, and starting
installation, removing, wiring, maintenance, and inspection of the products. Failure to turn power off may cause electrical
shocks or fire hazard.
To avoid a burn on your hand, use the lamp holder tool when replacing lamps.
For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a
tightening torque of 1.0 to 1.3 N·m. Failure to tighten terminal screws may cause overheat and fire.
Accessories (For Diecast Zinc Series Only) For other accessories, see pages 55 to 63.
Shape Material Type No. Ordering
Type No. Package
Quantity Description
Metal Bezel
Chrome-plated
OG-81 OG-81PN02 2
Cannot be used with half-shrouds.
OG-82 OG-82 1
Spare Key
Metal TW-SK-0 TW-SK-0PN02 2 For key selector switches
Maintenance Parts (For Diecast Zinc Series Only)
Shape Specification Type No. Ordering
Type No. Package
Quantity Description
Button
Plastic
ABN1BN-ABN1BN-PN05 5 Specify a color code in place of .
B (black), G (green), R (red), S
(blue), W (white), Y (yellow)
Above colors are used for ø30
diecast zinc control units (light
colored operator units).
ABN2BN-ABN2BN-PN05 5
ABN3BN-ABN3BN-PN02 2
Dummy
Block Plastic BST-D BST-DPN10 10 Used for 1NO or 1NC contact
blocks.
Snaps on to the operator unit.
Selector Operator
Plastic ASNHT-ASNHT-PN02 2Specify a color code in place of .
B (blue), G (green), R (red)
ASNHL-ASNHL-PN02
Color Insert TW-HC1TW-HC1PN05 5 Specify a color code in place of .
B (black), G (green), R (red), S
(blue), W (white), Y (yellow)
Safety Precautions
Instructions
Flush
(Octagonal) Extended
(Octagonal)
Flush
Mushroom
Extended
Knob Lever
Color
Insert
Tightening T orque for T erminal Screws
Tighten the M3.5 terminal screws to a torque of 1.0 to 1.3
N·m.
Replacement of Lamps
Lamps can be replaced by using the lamp holder tool (OR-
55) from the front of the panel.
How to remove
To remove, slip the lamp holder tool onto the lamp head
lightly. Then push slightly, and turn the lamp holder tool
counterclockwise.
How to install
To install, insert the lamp head into the lamp holder tool.
Place the pins on the lamp base to the groov es in the lamp
socket. Inset the lamp and turn it clockwise.
Installation of LED Illuminated Units
When using full voltage type LED illuminated units , provide
protection against electrical noise, if necessary. See page
65 for notes on LED illuminated units.
OR-55
IDEC CORPORATION (USA)
1175 Elko Drive, Sunnyvale, CA 94089-2209, USA
Tel: +1-408-747-0550, Toll Free: (800) 262-IDEC, Fax: +1-408-744-9055
E-mail: opencontact@idec.com, www.idec.com
IDEC CANADA LIMITED
Unit 22-151, Brunel Road Mississauga, Ontario, L4Z 1X3, Canada
Tel: +1-905-890-8561, Toll Free: (888) 317-4332, Fax: +1-905-890-8562
IDEC ELECTRONICS LIMITED
Unit 2, Beechwood, Chineham Business Park, Basingstoke, Hampshire
RG24 8WA, UK
Tel: +44-1256-321000, Fax: +44-1256-327755
E-mail: idec@uk.idec.com
IDEC ELEKTROTECHNIK GmbH
Wendenstrasse 331, D-20537 Hamburg, Germany
Tel: +49-40-25 30 54 10, Fax: +49-40-25 30 54 24
E-mail: service@idec.de, www.idec.de
IDEC AUSTRALIA PTY. LTD.
2/3 Macro Court, Rowville, Victoria 3178, Australia
Toll Free: 1-800-68-4332, Fax: +61-3-9763-3255
E-mail: sales@au.idec.com
7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan
Tel: +81-6-6398-2571, Fax: +81-6-6392-9731
www.idec.com
Specifications and other descriptions in this catalog are subject to change without notice.
Cat. No. EP1078-0 MARCH 2005 13DNP PRINTED IN JAPAN
IDEC IZUMI ASIA PTE. LTD.
No. 31, Tannery Lane #05-01, Dragon Land Building, Singapore 347788
Tel: +65-6746-1155, Fax: +65-6844-5995
E-mail: generalinfo@idecasia.com.sg
IDEC IZUMI (H.K.) CO., LTD.
Unit 1505-07, DCH Commercial Centre No. 25, Westlands Road,
Quarry Bay, Hong Kong
Tel: +852-2803-8989, Fax: +852-2565-0171
E-mail: idec@idechk.com
IDEC IZUMI (Shanghai) Co., Ltd.
Room E, 15F, Majesty Building, No. 138 Pudong Avenue, 
Shanghai 200120, P.R.C.
Tel: +86-21-5887-9181, Fax: +86-21-5887-8930
E-mail: idec@cn.idec.com
IDEC TAIWAN CORPORATION
8F, No. 79, Hsin Tai Wu Road, Sec. 1, Hsi-Chih, Taipei County, Taiwan
Tel: +886-2-2698-3929, Fax: +886-2-2698-3931
E-mail: service@idectwn.com.tw