o30 Series Control Units o30 o30 Series Control Units (Selection Guide) Function Emergency Stop Switch Category Pushlock Turn Reset Pushbutton Extended with Extended Half Shroud Momentary/Maintained Flush Extended with Full Shroud Shape Type HN1E ABN1 AON1 Page 6 13 (Diecast) ABD1 AOD1 69 Function Category (Diecast) ABD2 AOD2 69 ABN2 AON2 13 (Diecast) ABGD2 AOGD2 69 ABN2G AON2G 13 (Diecast) ABFD2 AOFD2 69 ABN2F AON2F 13 Pushbutton Mushroom with Mushroom Full Shroud Momentary/Maintained Palm Mushroom Jumbo Mushroom with Shallow Shroud Momentary Jumbo Mushroom with Deep Shroud Shape Type ABN3 AON3 Page 14 (Diecast) ABD3 AOD3 70 (Diecast) ABGD3 AOGD3 70 ABN3G 14 Function ABN4 (Diecast) ABD4 ABN4G (Diecast) ABGD4 ABN4F (Diecast) ABFD4 14 70 14 70 14 70 Pushbutton Mushroom Pushlock Turn Reset Square Flush Momentary Square Extended Momentary Type UBQN1 UBQN2 AVN3 Page 14 14 15 Category Mushroom Pushlock Key Reset Jumbo Mushroom Pushlock Key Reset ABN3K ABN4K 15 15 Mushroom Pull Mushroom Push-Pull Shape Function Category (Diecast) AVD3 71 Pushbutton Mushroom Push Turn Lock Key ON/OFF Lock Toggle Lever ABN5 ATN4 ATN23 15 15 16 Shape Type AJN3 Page 15 2 (Diecast) AJD3 71 (Diecast) AZD3 71 ATN21 ATN22 16 (Diecast) AYD3 71 o30 Series Control Units (Selection Guide) o30 Function Category Pin Lock Pushbutton Square Twin Momentary Square Twin Maintained Twin Maintained Pushbutton Flush Mushroom UWQN1 UWQN2 ABBN11 ABBN33 17 17 17 17 Pilot Light (LED) Square Rectangular (Marking) Shape Type ABN8P Page 16 Function Category (Diecast) ABD8P 71 Dome Pilot Light (Incandescent) Dome (1W) Dome (2W) Shape Type APN1 APNE1 Page 18 (Diecast) APD1 APDE1 72 Function Category UPQN4 UPQNE4 UPQN3B 19 19 Pilot Light (Incandescent) Rectangular (Marking) (1W/2W) Dome Square Flush (1W) Push-to-Check APN1 (Diecast) APD1 APN1 APNE1 19 72 18 (Diecast) APD1 APDE1 72 Illuminated Pushbutton (LED) Extended with Extended Half Shroud Momentary/Maintained Shape Type Page Function Category UPQN4 UPQNE4 UPQN3B APN1P 19 21 19 ALN2 ALNE2 AOLN2 AOLNE2 22 Illuminated Pushbutton (LED) Extended with Mushroom Mushroom Pushlock Full Shroud Turn Reset Momentary/Maintained (Diecast) ALD2 AOLD2 73 ALGN2 ALGNE2 AOLGN2 AOLGNE2 24 (Incandescent) Mushroom Push Turn Lock Extended Momentary/Maintained Shape Type Page ALFN2 (Diecast) ALFNE2 ALFD2 AOLFN2 AOLFD2 AOLFNE2 26 74 ALN3 ALNE3 AOLN3 AOLNE3 28 (Diecast) ALD3 AOLD3 AVLN3 AVLNE3 (Diecast) AVLD3 AVLDE3 AJLN3 75 31 76 31 ALN ALNE AOLN AOLNE 23 (Diecast) ALD2 AOLD2 73 3 o30 o30 Series Control Units (Selection Guide) Function Category Extended with Half Shroud Momentary Illuminated Pushbutton (Incandescent) Extended with Square Flush Rectangular Full Shroud Momentary/Maintained Momentary/Maintained Turn Lock Shape Type ALNG ALNE3G3 Page Function Category 25 ALNF ALNE3F3 AOLNF AOLNE3F3 27 (Diecast) ALFD2 AOLFD2 ULQN UOLQN 74 29 Illuminated Pushbutton (Incandescent) Mushroom Pushlock Mushroom Push Turn Reset Turn Lock ULQNB UOLQNB ALNL 29 30 Selector Switch Knob Lever Key Shape Type AVLN3 AVLNE3 Page 32 Function Category (Diecast) AVLD3 AVLDE3 76 Illuminated Selector Switch (LED) Knob AJLN3 ASN ASTN (Diecast) ASD ASNL ASTNL (Diecast) ASDL ASNK ASTNK (Diecast) ASDK 32 33/37 77 34/38 78 35/39 79 Illuminated Selector Switch (Incandescent) Knob Selector Pushbutton Ring Mono-Lever Switch Lever Standard Shape Type ASLN Page 40 (Diecast) ASLD 80 Function Mono-Lever Switch Category Interlocking ASLN 40 (Diecast) ASLD 80 (Diecast) ASBD2 82 ABN 42 (Diecast) ASBD2L 82 ABNL 42 ARN ARNS 44 Cam Switch Knob Key ACSNO ACSSO 47 ACSNK ACSSK 47 Maintained/ Spring Return Spring Return Shape Type ARNL Page 44 4 UCSQO 47 UCSQM 47 o30 HN Series Emergency Stop Switches Emergency Stop Switches (Unibody Type) Specifications Contact Ratings Specifications Rated Insulation Voltage (Ui) 250V Rated Thermal Current (Ith) 10A Rated Operational Voltage (Ue) 24V Resistive Load 6A AC (AC-12) 50/60 Inductive Load Hz 6A Rated (AC-15) Operational Resistive Load Current 6A (DC-12) DC Inductive Load 1.5A (DC-13) 110V 220V 3A 3A 3A 3A 2A 1A 0.3A 0.15A Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load (reference value): 3V AC/DC, 5 mA (Applicable range may vary with operating conditions and load types.) Operating Temperature Storage Temperature Operating Humidity Contact Resistance Insulation Resistance Dielectric Strength Vibration Resistance Shock Resistance Operating Frequency Life LED Lamp Ratings Unit Rated Operating Voltage 24V AC/DC Degree of Protection Terminal Style LED Lamp Type No. LSTD-2R Rated Voltage 24V AC/DC 10% Rated Current 10 mA Incandescent Lamp Ratings Unit Rated Operating Voltage 24V AC/DC Incandescent Lamp Type No. Wattage LS-3 1W (30V) -25 to +60C (no freezing) Illuminated units: -25 to +55C -40 to +80C 45 to 85% RH (no condensation) 50 m maximum (initial value) 100 M minimum (500V DC megger) Between live and dead metal parts Contacts: 2,500V AC, 1 minute Illuminated parts: 1,000V AC, 1 minute Damage limits: 60 m/s2 Operating extremes: 5 to 55 Hz, amplitude 0.5 mm Damage limits: 1,000 m/s2 Operating extremes: 100 m/s2 900 operations/h Mechanical: 250,000 operations minimum Electrical: 100,000 operations minimum IP65 M3.5 screw Applicable Standards and Approvals Safety Standards UL508 CSA C22.2 No. 14 EN60947-5-5 File No. or Organization UL Listing File No. E55996 c-UL (File No. E55996) DEMKO approved Pushlock Turn Reset Switches (Unibody Type) Shape Contact Type No. 1NO-1NC Button Color HN1E-BV411R Red only 2NC HN1E-BV402R * When pressed, the button is held depressed. The button is released by turning clockwise. * Terminal cover HW-VL7 is supplied with the switch. Illuminated Pushlock Turn Reset Switches (Unibody Type) Shape Lamp Contact 1NO-1NC Type No. Lens Color HN1E-LV411Q0R Without Lamp Red only 2NC HN1E-LV402Q0R * When pressed, the button is held depressed. The button is released by turning clockwise. * The illuminated pushlock turn reset switch does not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * Terminal cover HW-VL7 is supplied with the switch. 5 o30 HN Series Emergency Stop Switches Dimensions Panel Cut-Out * HN1E-BV4 M3.5 Terminal Screw Gasket Panel Thickness 0.8 to 6 R0 .8 m ax. o3 0 0 4.8+0.2 .5 +0. 33 0 5 0.5 Terminal Arrangement (Bottom View) TOP Marking Side Locking Ring o4 0 23.5 61 63 32 * HN1E-LV4 M3.5 Terminal Screw Gasket M3.5 Terminal Screw Terminal Arrangement (Bottom View) TOP Marking Side Panel Thickness 0.8 to 6 0.5 Lamp Terminal Locking Ring o4 0 X1 LAMP X2 23.5 All dimensions in mm. 61 63 32 Replacement Parts Name Terminal Cover Type No. HW-VL7 Ordering Type No. Package Quantity HW-VL7PN10 10 Remarks Used on HN1E emergency stop switches for preventing electrical shocks. The HW-VL7 terminal cover is supplied with the HN1E. Nameplates Shape Type No. HNAV-0 Legend Package Quantity (blank) 1 HNAV-27 EMERGENCY STOP Remarks Background: Yellow Legend: Black Applicable panel thickness: 0.8 to 4.5 mm Material: Polyamide Legend "EMERGENCY STOP" is indicated outside a o44mm circle. o60 o3 0 1.5 1.0 Accessory Metal TWST-T1 Package Quantity 1 Remarks * Used for tightening the locking nut. * Tighten the locking nut to a torque of 2.0 to 2.5 N*m. 23.7 6 20.5 Type No. 52 Material 49.5 Shape 77 o30 o30 Series Control Units Heavy duty control units offer both variety and reliability Endures harsh environments * Degree of protection: IP65 * UL, CSA approved, and EN compliant. Safety Standards File No. or Organization UL UL Listing File No. E68961 CSA File No. LR21451 EN EN60947-5-1 Specifications and Ratings Contact Ratings Pushbuttons Illuminated Pushbuttons Selector Switches Illuminated Selector Switches Selector Pushbuttons Contact Block Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 Type BS/BST (o30 series) 600V 10A AC-15 (A600) DC-13 (P600) Characteristics * Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V 10A 10A 10A 5A 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types) For mono-levers and cam switches, see pages 43 and 46. BS (BST) Contact Block * Contact Block Types Single-pole Contact Block Type * Interlocking Groove * M3.5 Terminal Screw Contact * Mounting Screw BS Type BST Push Rod * Inspection Window * Push Rod 1NO BS010E BST010 Green 1NC BS001E BST001 Red 1NO (early make) BS010SE BST010S Black 1NC (late break) BS001SE BST001S White BST contact blocks are used for the following control units and are not interchangeable with BS contact blocks. (The BS housing is dark gray and the BST housing is light gray.) * Pushlock turn reset and push turn lock switches * LED illuminated pushbuttons * LED/incandescent illuminated selector switches * All models of diecast zinc housing control units * Durable nylon 66 housing has a high resistance against alkalis. * Silver contacts. * Up to four blocks in two layers can be mounted onto each operator. 7 o30 o30 Series Control Units LED Illuminated Unit Specifications Color Code Unit Input Type Full Voltage A: G: Pilot Light PW: Illuminated Pushbutton R: Illuminated Selector Switch S: W: Y: amber green pure white red blue white yellow Transformer Operating Voltage 6V AC/DC 12V AC/DC 24V AC/DC 6V AC/DC 12V AC/DC 24V AC/DC 100/110V AC/DC 115V AC/DC 120V AC/DC 200/220V AC/DC 230V AC/DC 240V AC/DC 380V AC/DC 400/440V AC/DC (50/60 Hz) DC-DC Converter 110V DC LED Lamp Type No. Voltage LSTD-6 6V AC/DC 10% LSTD-1 12V AC/DC 10% LSTD-2 24V AC/DC 10% LETD-6 6V AC/DC 10% LETD-8 12V AC/DC 10% LETD-2 24V AC/DC 10% Lamp Base BA9S/13 E12/15 BA9S/13 LSTD-6 6V AC/DC 10% E12/15 LETD-6 BA9S/13 E12/15 LSTD-6 LETD-6 6V AC/DC 10% Incandescent Illuminated Unit Specifications Color Code Unit Input Type Full Voltage Pilot Light Illuminated Pushbutton Illuminated Selector Switch A: G: O: R: S: W: amber green orange red blue white Transformer Operating Voltage 6V AC/DC 12V AC/DC 24V AC/DC 6V AC/DC 12V AC/DC 24V AC/DC 100/110V AC/DC 115V AC/DC 120V AC/DC 200/220V AC/DC 230V AC/DC 240V AC/DC 380V AC/DC 400/440V AC/DC 480V AC/DC (50/60 Hz) Lamp Base BA9S/13 E12/15 Incandescent Lamp Type No. Rating LS-6 1W (6.3V) LS-8 1W (18V) LS-3 1W (30V) LE-6 2W (6.3V) LE-8 2W (18V) LE-3 12W (30V) BA9S/13 LS-6 1W (6.3V) E12/15 LE-8 2W (18V) LED Lamp Ratings (LSTD Type) Type No. Lamp Base Rated Voltage Voltage Range Current Draw AC DC Color Code Lamp Base Color Voltage Marking Life (reference value) Internal Circuit LSTD-6 LSTD-1 LSTD-2 BA9S/13 6V AC/DC 12V AC/DC 24V AC/DC 6V AC/DC 10% 12V AC/DC 10% 24V AC/DC 10% A, R, W, Y: 17 mA 11 mA 11 mA G, PW, S: 8 mA A, R, W, Y: 14 mA 10 mA 10 mA G, PW, S: 5.5 mA A (amber), G (green), PW (pure white), R (red), S (blue), W (white), Y (yellow) Same as illumination color Die stamped on the base Approx. 50,000 hours (The luminance is reduced to 50% the initial intensity when used on complete DC.) A, R, W, Y A, R, W, Y G, PW, S LED Chip Protection Diode Zener Diode 8 o30 Series Control Units o30 LED Lamp Ratings (LETD Type) Type No. Lamp Base Rated Voltage Voltage Range LETD-6 LETD-8 LETD-2 E12/15 6V AC/DC 12V AC/DC 24V AC/DC 6V AC/DC 10% 12V AC/DC 10% 24V AC/DC 10% A, R, W, Y: 17 mA AC 7 mA 11 mA G, S: 8 mA Current Draw A, R, W, Y: 14 mA DC 6.5 mA 10 mA G, S: 5.5 mA Color Code A (amber), G (green), R (red), S (blue), W (white), Y (yellow) Lamp Base Color Same as illumination color Voltage Marking Die stamped on the base Approx. 50,000 hours Life (reference value) (The luminance is reduced to 50% the initial intensity when used on complete DC.) A, R, W, Y A, R, W, Y Internal Circuit G, S LED Chip Protection Diode Zener Diode Incandescent Lamp Ratings (LS Type) Type No. Lamp Base Rated Voltage Wattage Voltage Marking LS-6 LS-8 LS-2 BA9S/13 6V AC/DC 12V AC/DC 18V AC/DC 1W (6.3V) 1W (18V) 1W (24V) Die stamped on the base Approx. 1,000 hours minimum Life (reference value) (mean value when used on the rated voltage) LS-3 24V AC/DC 1W (30V) Incandescent Lamp Ratings (LE Type) Type No. Lamp Base Rated Voltage Wattage Voltage Marking LE-6 LE-8 LE-2 E12/15 6V AC/DC 12V AC/DC 18V AC/DC 2W (6.3V) 2W (18V) 2W (24V) Die stamped on the base Approx. 1,000 hours minimum Life (reference value) (mean value when used on the rated voltage) LE-3 24V AC/DC 2W (30V) 9 o30 o30 Series Control Units Specifications Operating Temperature Operating Humidity Contact Resistance Insulation Resistance Dielectric Strength Vibration Resistance Shock Resistance Mechanical Life (minimum operations) Electrical Life (minimum operations) -25 to +50C (no freezing) 45 to 85% RH (no condensation) 50 m maximum (initial value) 100 M minimum (500V DC megger) Between live and dead metal parts: 2,500V AC, 1 minute (Full voltage type and pilot lights: 2,000V AC, 1 minute) Operating extremes: 5 to 55 Hz, amplitude 0.5 mm Damage limits: 1,000 m/s2 Operating extremes: 100 m/s2 Pushbuttons Momentary: 5,000,000 Maintained: 500,000 Illuminated pushbuttons Momentary: 2,500,000 Maintained: 500,000 Selector switches: 500,000 Key selector switches: 500,000 Illuminated selector switches: 500,000 Selector pushbuttons: 250,000 Mono-lever switches: 500,000 (Interlocking type): 250,000 Pushlock turn reset 500,000 Mushroom push-pull switch Two contact blocks: 500,000 Four contact blocks: 200,000 Pushbuttons: 500,000 1 Illuminated pushbuttons: 500,000 1 Selector switches: 500,000 2 Key selector switches: 500,000 2 Illuminated selector switches: 500,000 2 Selector pushbuttons: 250,000 2 Mono-lever switches: 500,000 3 (Interlocking type): 250,000 3 1 Switching frequency 1,800 operations/h, duty ratio 40% 4 2 Switching frequency 1,200 operations/h, duty ratio 40% 3 Switching frequency 900 operations/h, duty ratio 40% 4 Switching frequency 900 operations/h for square twin or twin maintained types Degree of Protection Type No. Unit NEMA ICS 6-110 IEC 60529 Pushbuttons, pilot lights, illuminated pushbuttons, selector switches, selector Type 1, 2, 3, 3R, (3S), 4, 5, 12,13 IP65 pushbuttons, mono-lever switches, and cam switches (ACSNO/ACSSO) A U Illuminated selector switches, key pushbuttons, key reset pushbuttons, key cam switches, and key selector switches Type 1, 2, 3, 3R, 5, 12, 13 IP54 Square pushbuttons, square pilot lights, and cam switches (UC) Type 1, 2 IP40 Note: (3S) of NEMA ICS 6-110 applies to the pilot lights with round lens. Mounting Hole Layout (Twin Maintained Type) R0.8 max. 4.8 +0.2 0 o3 +0 . 0 5 4.8 +0.2 0 o3 0.5 +0 . 0 5 50 Round Unit: 42 Square Unit: 55 33 +0.5 0 0.5 33 +0.5 0 R0.8 max. The minimum mounting centers are applicable to switches with one layer of contact blocks (two contact blocks). When two layers of contact blocks (four contact blocks) are mounted, determine the minimum mounting centers in consideration of convenience for wiring. * Mushroom with shroud: 50 mm minimum * Jumbo mushroom: 67 mm minimum * Jumbo mushroom with shroud: 76 mm minimum * Square twin: 55 mm minimum * Selector switch with lever: 50 mm minimum The 4.8 mm recess is for preventing rotation and is not necessary when the nameplate or anti-rotation ring is not used. 50 Note: For mounting hole layout of pushbuttons, mono-lever switches, and cam switches, see each section. 10 o30 Series Control Units (Ordering Information) o30 Ordering Information Standard Units Terminal Cover * Specify an operator or lens color code in the Type No. * Black, green, and red buttons are included with flush pushbuttons. * Full voltage type illuminated units are not supplied with a lamp. Order LED or incandescent lamps separately. Transformer and DC-DC converter type illuminated units contain an LED or incandescent lamp. * Terminal covers, nameplates, and accessories are ordered separately. * When a terminal cover is required, order an applicable terminal cover referring to page 55. The Type No. development charts shown below can be used to specify control units other than those listed on the following pages. Gold-plated silver contacts are also available. o30 Series Pushbuttons o30 Series Illuminated Pushbuttons ABN2 11 R - MAU ALFN2 116 13 D N R - MAU Optional contact MAU: Gold-plated silver contact Button color code Contact arrangement code 10: 1NO 01: 1NC 11: 1NO-1NC 20: 2NO 02: 2NC 21: 2NO-1NC 12: 1NO-2NC 30: 3NO 03: 3NC 31: 3NO-1NC 22: 2NO-2NC 13: 1NO-3NC 40: 4NO 04: 4NC Note: * Mushroom pull type ATN23 can have a maximum of two contact blocks. * Mushroom push-pull return type ATN22 cannot have only NO or only NC contacts. * No other contact configurations are available for square twin type UWQN1 than those specified in this catalog. o30 Series Pilot Lights APN1 116 D R Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Operating voltage code 99: Full voltage 16/18: Transformer (100/110V AC) 116/118: Transformer (115V AC) 126/128: Transformer (120V AC) 26/28: Transformer (200/220V AC) 236/238: Transformer (230V AC) 246/248: Transformer (240V AC) 386/388: Transformer (380V AC) 46/48: Transformer (400/440V AC) 486/488: Transformer (480V AC) 16D: DC-DC converter (110V DC) Optional contact MAU: Gold-plated silver contact Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Contact arrangement code 11: 1NO-1NC 20: 2NO 02: 2NC 31: 3NO-1NC 22: 2NO-2NC 13: 1NO-3NC 40: 4NO 04: 4NC Operating voltage code 99: Full voltage 16/18: Transformer (100/110V AC) 116/118: Transformer (115V AC) 126/128: Transformer (120V AC) 26/28: Transformer (200/220V AC) 236/238: Transformer (230V AC) 246/248: Transformer (240V AC) 386/388: Transformer (380V AC) 46/48: Transformer (400/440V AC) 486/488: Transformer (480V AC) 16D: DC-DC converter (110V DC) Note: * Illuminated pushbuttons cannot have an odd number of contact blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and 3NC. * Transformer and DC-DC converter types contain an LED lamp (LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8, 2W). * LED lamps cannot be used on 480V AC transformers. * DC-DC converter is available with LED lamps only. * Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48, and 488 are available for incandescent types only. Note: * Full voltage type is not supplied with a lamp. * Transformer and DC-DC converter types contain an LED lamp (LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8, 2W). * LED lamps cannot be used on 480V AC transformers. * DC-DC converter is available with LED lamps only. * Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48, and 488 are available for incandescent types only. 11 o30 o30 Series Control Units (Ordering Information) o30 Series Selector Switch o30 Series Illuminated Selector Switch ASN 2 L 11 - MAU ASLN 2 16 22 D N R - MAU Optional contact MAU: Gold-plated silver contact Contact arrangement code Operator type (blank): Knob L: Lever Number of positions o30 Series Key Selector Switch ASN 2 K 20 B - MAU Optional contact MAU: Gold-plated silver contact Key removable position code 2-position * Maintained (blank): Removable in all positions B: Removable in left only C: Removable in right only * Spring return from right (blank): Removable in left only * Spring return from left (blank): Removable in right only 3-position * Maintained (blank): Removable in all positions B: Removable in left and center C: Removable in right and center D: Removable in center only E: Removable in right and left G: Removable in left only H: Removable in right only * Spring return from right (blank): Removable in left and center D: Removable in center only G: Removable in left only * Spring return from left (blank): Removable in right and center D: Removable in center only H: Removable in right only * Spring return two-way (blank): Removable in center only Contact arrangement code Number of positions Note: * The key cannot be removed in the return position. 12 Optional contact MAU: Gold-plated silver contact Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Contact arrangement code Operating voltage code 99: Full voltage 16: Transformer (100/110V AC) 156: Transformer (115V AC) 136: Transformer (120V AC) 26: Transformer (200/220V AC) 236: Transformer (230V AC) 256: Transformer (240V AC) 386: Transformer (380V AC) 46: Transformer (400/440V AC) 486: Transformer (480V AC) Number of positions Note: * Full voltage type is not supplied with a lamp. * Transformer type contain an LED lamp (LSTD-6) or incandescent lamp (LS-6, 1W). * LED lamps cannot be used on 480VAC transformers. o30 Series Pushbuttons o30 Flush / Extended / Extended w/Half Shroud / Extended w/Full Shroud Types Flush AON1 Maintained 1NO AON110 1NC AON101 1NO-1NC AON111 2NO AON120 2NC AON102 Momentary ABN210 1NC ABN201 91 (3 to 4 blocks) 1NO-1NC ABN211 2NO ABN220 2NC ABN202 1NO AON210 1NC AON201 Maintained 46 (1 or 2 blocks) 2NO AON220 2NC AON202 ABN2G10 1NC ABN2G01 1NO-1NC ABN2G11 2NO ABN2G20 2NC ABN2G02 1NO AON2G10 1NC AON2G01 1NO-1NC AON2G11 2NO AON2G20 2NC AON2G02 1NO ABN2F10 1NC ABN2F01 40 68 (1 to 2 blocks) 9 91 (3 to 4 blocks) M3.5 Terminal Screw 15.5 Panel Thickness 0.8 to 4 Specify a button color code in place of in the Type No. 23 6 40 42 (1 or 2 blocks) 20.5 65 (3 or 4 blocks) B: G: R: W: Y: black green red white yellow M3.5 Terminal Screw Panel Thickness 0.8 to 4 23 6 40 64 (1 or 2 blocks) 87 (3 or 4 blocks) 20.5 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 1NO-1NC ABN2F11 2NO ABN2F20 6 AON2F01 40 17 69 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o25 AON2F10 1NC 23 46 (1 or 2 blocks) ABN2F02 1NO 1NO-1NC AON2F11 2NO AON2F20 2NC AON2F02 36 23 6 2NO-2NC ABN2F22 Maintained Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw o25 o27 o35 1NO 2NC Extended with Full Shroud AON2F 15.5 o25 o28.5 Momentary 40 9 69 (3 or 4 blocks) 2NO-2NC AON2G22 Extended with Full Shroud ABN2F 23 6 1NO-1NC AON211 2NO-2NC ABN2G22 Extended with Half Shroud AON2G Panel Thickness 0.8 to 7.5 o25 o27 o35 Momentary 9 M3.5 Terminal Screw 2NO-2NC AON222 Extended with Half Shroud ABN2G 40 68 (1 to 2 blocks) o25 Maintained 23 6 2NO-2NC ABN222 Extended AON2 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw Specify Y or W when a yellow or white button is required. o25 1NO 9 69 (3 or 4 blocks) 2NO-2NC AON122 Extended ABN2 40 46 (1 or 2 blocks) 36 2NO-2NC ABN122 23 6 36 ABN102 36 2NC Black (B), green (G), and red (R) buttons are supplied with each unit. 36 ABN120 2NO-2NC AON2F22 36 2NO 36 1NO-1NC ABN111 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 23 36 ABN101 o35 ABN110 1NC Dimensions (mm) o35 1NO Button Color Code o35 Momentary Type No. o35 Flush ABN1 Contact o35 Operation Type o28.5 o35 Shape 40 68 (1 or 2 blocks) 91 (3 or 4 blocks) 17 * Round bezel and shroud (metal): Chrome-plated * Other contact arrangements and gold-plated silver contacts are also available. See page 11. 13 o30 o30 Series Pushbuttons Mushroom / Jumbo Mushroom / Square Flush / Square Extended Types Maintained 1NO-1NC ABN311 2NO ABN320 2NC ABN302 46 (1 or 2 blocks) 2NO-2NC ABN322 69 (3 or 4 blocks) 1NO AON310 1NC AON301 1NO-1NC AON311 2NO AON320 2NC AON302 Momentary ABN3G10 1NC ABN3G01 Momentary black green red white yellow Momentary Momentary 91 (3 or 4 blocks) 1NO-1NC ABN3G11 2NO ABN3G20 2NC ABN3G02 6 ABN410 1NC ABN401 2NO ABN420 2NC ABN402 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 ABN4G10 1NC ABN4G01 1NO-1NC ABN4G11 2NO ABN4G20 2NC ABN4G02 ABN4F10 1NC ABN4F01 35 69 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: black G: green R: red 6 23 46 (1 or 2 blocks) 28 69 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw o75 1NO 23 46 (1 or 2 blocks) o65 1NO 1NO-1NC ABN4F11 2NO ABN4F20 2NC ABN4F02 6 UBQN110 1NC UBQN101 23 46 (1 or 2 blocks) 32.5 69 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 34 1NO 1NO-1NC UBQN111 2NO UBQN120 UBQN102 1NO UBQN210 1NC UBQN201 6 B: G: R: Y: black green red yellow 23 47.5 (1 or 2 blocks) 14 (3 70.5 or 4 blocks) M3.5 Terminal Screw 40 44 Panel Thickness 0.8 to 5.5 1NO-1NC UBQN211 2NO 2NC UBQN220 UBQN202 2NO-2NC UBQN222 * Specify a button color code in place of in the Type No. * Round bezel and shroud (metal): Chrome-plated * Other contact arrangements and gold-plated silver contacts are also available. See page 11. 14 23 67 (3 or 4 blocks) 1NO-1NC ABN411 2NO-2NC UBQN122 Momentary 23 44 (1 or 2 blocks) o74 1NO 2NC Square Extended UBQN2 Panel Thickness 0.8 to 6.5 34 Momentary 21 M3.5 Terminal Screw 2NO-2NC ABN4F22 Square Flush UBQN1 40 68 (1 or 2 blocks) 2NO-2NC ABN4G22 Jumbo Mushroom with Deep Shroud ABN4F Panel Thickness 0.8 to 7.5 23 6 2NO-2NC ABN422 Jumbo Mushroom with Shallow Shroud ABN4G 21 M3.5 Terminal Screw B: G: R: W: Y: 2NO-2NC ABN3G22 Palm Mushroom ABN4 40 o48 1NO 23 6 2NO-2NC AON322 Mushroom with Full Shroud ABN3G Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 36 ABN301 36 ABN310 1NC Dimensions (mm) 36 52.2 Mushroom AON3 1NO Button Color Code 36 52.2 Momentary Type No. o40 Mushroom ABN3 Contact o40 Operation Type o75 Shape 6 23 47.5 (1 or 2 blocks) 70.5 (3 or 4 blocks) 20 40 44 o30 Series Pushbuttons o30 Pushlock Turn Reset / Pushlock Key Reset / Push Turn Lock / Key ON/OFF Lock / Toggle Lever Types 1NO ABN3K10 1NC ABN3K01 1NO-1NC ABN3K11 2NO ABN3K20 2NC ABN3K02 2NO-2NC ABN3K22 1NO ABN4K10 1NC ABN4K01 1NO-1NC ABN4K11 2NO ABN4K20 2NC ABN4K02 2NO-2NC ABN4K22 1NO AJN310N 1NC AJN301N 1NO-1NC AJN311N 2NO AJN320N 2NC AJN302N 2NO-2NC AJN322N 1NO ABN510 1NC ABN501 1NO-1NC ABN511 2NO ABN520 2NC ABN502 2NO-2NC ABN522 1NO ATN410 1NC ATN401 1NO-1NC ATN411 2NO ATN420 2NC ATN402 2NO-2NC ATN422 36 24 76 (3 or 4 blocks) M3.5 Terminal Screw B: G: R: Y: black green red yellow FR Panel Thickness 0.8 to 7.5 EE 36 AVN322N 40 53 (1 or 2 blocks) 23 6 40 53 (1 or 2 blocks) 23.5 24 76 (3 or 4 blocks) FR Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: black G: green R: red EE 23 6 53 (1 or 2 blocks) 23 23.5 76 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: G: R: Y: black green red yellow 23 5.5 L H 36 2NO-2NC 23 5.5 40 53 (1 or 2 blocks) 24 76 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 - 23 6 LOCK 90 36 AVN302N o40 2NC R: red Y: yellow o65 AVN320N o40 AVN311N 2NO Panel Thickness 0.8 to 7.5 40 54 (1 or 2 blocks) 23 23.5 77 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 36 Toggle Lever ATN4 1NO-1NC M3.5 Terminal Screw K OC Key ON/OFF Lock ABN5 AVN301N PUS Mushroom Push Turn Lock AJN3 AVN310N 1NC Dimensions (mm) o35 Jumbo Mushroom Pushlock Key Reset ABN4K 1NO Button Color Code o40 Mushroom Pushlock Key Reset ABN3K Type No. o25 Mushroom Pushlock Turn Reset AVN3 Contact o35 Shape Lever: black 6 23 44 (1 or 2 blocks) 40 25 67 (3 or 4 blocks) * Specify a button color code in place of in the Type No. * Round bezel (metal): Chrome-plated * Cylinder (metal): Chrome-plated * Other contact arrangements and gold-plated silver contacts are also available. See page 11. * Pushlock Turn Reset: Button is maintained when pressed and is reset when turned clockwise. Red buttons only. Note: AVN3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Pushlock Key Reset: Button is maintained when pressed and is reset with a key. Key is removable from both depressed and reset positions. Two keys are supplied. * Push Turn Lock: Button is locked when turned clockwise in the depressed position and is reset when turned counterclockwise. * Key ON/OFF Lock: Button can be locked in both depressed and reset positions. * Toggle Lever: ON and OFF are indicated on the cap. 15 o30 o30 Series Pushbuttons Pull / Push-Pull / Pin Lock Types ATN2320 2NC ATN2302 1NO-1NC ATN2111 2NO ATN2120 2NC ATN2102 2NO-2NC ATN2122 1NO-1NC ATN2211 40 53 (1 or 2 blocks) M3.5 Terminal Screw B: G: R: Y: black green red yellow 6 38.5 Panel Thickness 0.8 to 7.5 23 53 (1 or 2 blocks) (3 76 or 4 blocks) 40 38.5 Panel Thickness 0.8 to 7.5 6 23 53 (1 or 2 blocks) 76 (3 or 4 blocks) ATN2222 C ABN8P10 1NC ABN8P01 1NO-1NC ABN8P11 2NO ABN8P20 2NC ABN8P02 2NO-2NC ABN8P22 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw - 6 36 1NO 40 38.5 23 44.5 (1 or 2 blocks) 40 49 26.5 67 (3 or 4 blocks) 1NO ABN8P10-TK231-1 1NC ABN8P01-TK231-1 1NO-1NC ABN8P11-TK231-1 2NO ABN8P20-TK231-1 2NC ABN8P02-TK231-1 2NO-2NC ABN8P22-TK231-1 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw - 6 36 Pin Lock ABN8P 36 o40 M3.5 Terminal Screw 2NO-2N Pin Lock (ON Lock Type) ABN8P -TK231-1 23 6 36 2NO 36 ATN2311 Panel Thickness 0.8 to 7.5 51 1NO-1NC M3.5 Terminal Screw o28 o35 Mushroom Push-Pull (Spring Return) ATN22 ATN2310 Dimensions (mm) o28 o35 Mushroom Push-Pull ATN21 1NO Button Color Code 51 Mushroom Pull ATN23 Type No. o40 Contact o40 Shape 23 44 (1 or 2 blocks) 67 (3 or 4 blocks) 25.4 40 49 * Specify a button color code in place of in the Type No. * Round bezel and shroud (metal): Chrome-plated * Square bezel (metal): Chrome-plated * Other contact arrangements and gold-plated silver contacts are also available. See page 11. * Pull: Pulling the button operates the contacts. Up to 2 contact blocks (1 layer) can be mounted on pull switches. * Push-Pull: Button is maintained in both depressed and reset positions. * Push-Pull (Spring Return): Pushing or pulling the button operates the contacts. Button is spring-returned to the center position. * Pin Lock: Button can be locked in either depressed or reset position by inserting the pin. Pad lock with a o6mm pin can also be used to lock the button. * Pin Lock (ON Lock Type): Button is locked in the depressed position by inserting the pin. Button cannot be locked in the reset position. * Contact Operation Pull Switch (Spring Return) Contact Push-Pull Switch (Maintained) Contact ATN21 Push Pull Push-Pull (Spring Return) Switch Contact 1NO 1NO-1NC 1NO-1NC 1NC 2NO 2NO-2NC 1NO-1NC 2NC 2NO 2NO-2NC 2NC 16 ATN23 Normal Pull Push ATN22 Normal Pull o30 Series Pushbuttons o30 Square Twin / Twin Maintained Types Shape Square Twin (Momentary) UWQN1 ON Contact OFF 1NO 1NO Type No. Button Color UWQN11010 Dimensions (mm) M3.5 Terminal Screw Panel Thickness 0.8 to 13 1NO 1NC UWQN11001 42 O N ON: Black OFF: Red OFF 6 23 36 53 47 (1 or 2 blocks) 15.5 70 (3 or 4 blocks) Square Twin (Maintained) UWQN2 2NO 2NC ON OFF 1NO - UWQN12002 UWQN21000 Panel Thickness 0.8 to 13 M3.5 Terminal Screw 1NO-1NC - - UWQN20100 UWQN21100 ON ON: Black OFF: Red 42 1NC OFF 6 23 36 53 47 (1 block) UWQN22000 2NC - UWQN20200 Top Bottom 1NO - ABBN1110 1NC - ABBN1101 1NO-1NC - ABBN1111 2NO - ABBN1120 2NC - ABBN1102 2NO-2NC - ABBN1122 Top Bottom 1NO - ABBN3310 1NC - ABBN3301 1NO-1NC - ABBN3311 2NO - ABBN3320 2NC - ABBN3302 2NO-2NC - ABBN3322 Black (B), green (G), and red (R) buttons are supplied with each unit. M3.5 Terminal Screw 9 50 86 - 15.5 o35 Flush Twin Maintained ABBN11 2NO 70 (2 blocks) 57 80 M3.5 Terminal Screw 40 21 50 86 Order buttons separately. See page 61. Panel Thickness 0.8 to 7.5 o40 Mushroom Twin Maintained (Without buttons) ABBN33 Other color buttons are separately ordered. See page 61. 57 80 Panel Thickness 0.8 to 7.5 40 * Round bezel (metal): Chrome-plated * Other contact arrangements and gold-plated silver contacts are also available. See page 11. * Square Twin (Momentary): Two independent momentary switches are contained in one unit, each operated by ON or OFF button. With the o30 adapter removed form the sleeve, the unit can mount in a o25.5mm mounting hole for the o25 series. * Square Twin (Maintained): The contact operates when ON button is pressed and is maintained in the depressed position. The button is reset by pressing the OFF button. * Twin Maintained: The contact operates when the top button is pressed and is maintained in the depressed position. The button is reset by pressing the bottom button. Different combinations of flush, extended buttons, and colors are available (ABN1B-, ABN2B-). See page 61. Mushroom buttons for the ABBN33 are ordered separately. Specify the color code (ABN3B-). See page 61. 17 o30 o30 Series Pilot Lights Dome Types Shape Lamp Input Type Dome APN1 APNE1 Lamp Receptacle Type No. BA9S APN199 E12 APNE199 BA9S APN1DN E12 APNE1DN BA9S APN116DDN E12 APNE116DDN BA9S APN1 E12 APN1 Without Lamp Full Voltage Transformer LED DC-DC Converter Incandescent Transformer Lens/LED Color Code A: amber C: clear G: green O: orange R: red S: blue W: white Y: yellow A: amber G: green PW: pure white R: red S: blue W: white Y: yellow C: clear G: green O: orange R: red S: blue W: white Applicable Lamp LSTD LS (1W) LETD LE (2W) LSTD-6 LETD-6 LSTD-6 LETD-6 LS-6 (1W) LE-8 (2W) * Operating Voltage Code Specify an operating voltage code in place of in the Type No. Operating Voltage Code LED Transformer BA9S and E12 Types Incandescent Transformer E12 Type Incandescent Transformer BA9S Type 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC (incandescent only) 488: 480V AC * Specify a lens/LED color code in place of in the Type No. Use the white lens (W) for LED pure white illumination. * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC). Pure white is available for BA9S lamp base types only. Dimensions * Full Voltage Type Panel Thickness 0.8 to 7.5 21.5 23.5 36 o35 M3 Terminal Screw 40 * Transformer Type * DC-DC Converter Type Panel Thickness 0.8 to 7.5 58.5 23.5 36 o35 M3.5 Terminal Screw 40 All dimensions in mm. 18 o30 Series Pilot Lights o30 Square / Rectangular (Marking) Types Shape Lamp Input Type Lamp Receptacle Type No. Square UPQN3B Without Lamp Full Voltage BA9S UPQN3B99 Transformer BA9S UPQN3BD DC-DC Converter BA9S UPQN3B16DD Transformer BA9S UPQN3B Without Lamp Full Voltage BA9S UPQN499 Transformer BA9S UPQN4D DC-DC Converter BA9S UPQN416DD Transformer BA9S UPQN4 Without Lamp Full Voltage E12 UPQNE499 Transformer E12 UPQNE4D DC-DC Converter E12 UPQNE416DD Transformer E12 UPQN4 LED Incandescent Rectangular (Marking Type) UPQN4 LED Incandescent Rectangular (Marking Type) UPQNE4 UPQN4 LED Incandescent Lens/LED Color Code A: amber C: clear G: green O: orange R: red S: blue W: white Y: yellow A: amber G: green R: red S: blue W: white Y: yellow C: clear G: green O: orange R: red S: blue W: white A: amber G: green O: orange R: red S: blue W: white Y: yellow A: amber G: green R: red S: blue W: white Y: yellow G: green O: orange R: red S: blue W: white A: amber G: green O: orange R: red S: blue W: white Y: yellow A: amber G: green R: red S: blue W: white Y: yellow G: green O: orange R: red S: blue W: white Applicable Lamp LSTD LS (1W) LSTD-6 LSTD-6 LS-6 (1W) LSTD LS (1W) LSTD-6 LSTD-6 LS-6 (1W) LETD LE (2W) LETD-6 LETD-6 LE-8 (2W) 19 o30 o30 Series Pilot Lights * Operating Voltage Code Specify an operating voltage code in place of in the Type No. Operating Voltage Code LED Transformer BA9S and E12 Types Incandescent Transformer E12 Type Incandescent Transformer BA9S Type 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC (incandescent only) 488: 480V AC * Specify a lens/LED color code in place of in the Type No. * On the rectangular marking type, a clear lens and a color marking plate are used for white illumination. * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). * Marking plate for the rectangular marking type: 24 x 30 mm, 2 mm thick DC-DC converter types are not approved by UL and CSA, and not CE compliant (operating voltage 90 to 140V DC). Dimensions * Rectangular Full Voltage Type UPQN4 20 66 40 44 10.5 40 44 36 52.2 34 x 40 10.5 40 * Rectangular Transformer Type * Rectangular DC-DC Converter Type UPQNE4 M3.5 Terminal Screw 36 52.2 52.2 36 34 36.5 Panel Thickness 0.8 to 4.5 30 x 36 M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 25 60 40 44 * Rectangular Transformer Type * Rectangular DC-DC Converter Type UPQN4 * Square Transformer Type * Square DC-DC Converter Type UPQN3B M3.5 Terminal Screw 10.5 Panel Thickness 0.8 to 4.5 74 36 52.2 29.5 36 52.2 34 x 40 40 44 34 x 40 20 Panel Thickness 0.8 to 4.5 M3 Terminal Screw 36 52.2 34 23 Panel Thickness 0.8 to 4.5 M3 Terminal Screw 34 x 40 Panel Thickness 0.8 to 5.5 M3 Terminal Screw * Rectangular Full Voltage Type UPQNE4 30 x 36 * Square Full Voltage Type UPQN3B 10.5 40 All dimensions in mm. * Reflector 1. The lamp housing of the square type LED illuminated pilot lights has a built-in reflector. 2. Make sure that the reflector does not fall off when removing the lens or marking plate. 3. When replacing the LED lamp of UPQNE4 (rectangular) type, use a lamp holder tool (OR-55). 4. To remove the reflector, insert a flat screwdriver inside the groove of the reflector and lightly push out. Groove * Panel Mounting 1. Tighten the square ring to the operator and position the ring correctly. 2. Lightly tighten the screw to secure the pilot light onto the panel. Screw Tighten the screw lightly so that the panel does not bend. Recommended tightening torque: 0.15 N*m 20 o30 Series Pilot Lights o30 Incandescent Push-to-Check Types (1W) Shape Lamp Input Type Lamp Receptacle Lens/LED Color Code Type No. Applicable Lamp Push-to-Check APN1P Without Lamp Full Voltage BA9S APN199P Incandescent BA9S APN1P Transformer C: G: O: R: S: W: clear green orange red blue white LS (1W) LS-6 (1W) * Operating Voltage Code Specify an operating voltage code in place of in the Type No. Operating Voltage Code 16: 100/110V AC 116: 115V AC 126: 120V AC 26: 200/220V AC 236: 230V AC 246: 240V AC 386: 380V AC 46: 400/440V AC 486: 480V AC * Specify a lens color code in place of in the Type No. * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC). Circuit Example START OLS STOP M Note: The lamp of push-to-check pilot light is not connected to the contact terminal. To connect, refer to the diagram on the left. L M Push-to-Check Pilot Light Dimensions * Push-to-Check APN1P M3 Lamp Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 6 23 36 o35 M3.5 Terminal Screw 40 A: 62.5 B: 96.5 23.5 A: Full voltage type B: Transformer type All dimensions in mm. 21 o30 o30 Series Illuminated Pushbuttons LED Round Extended Illuminated Pushbuttons Lamp Receptacle Shape Round Extended ALN2 AOLN2 ALNE2 AOLNE2 Operation Type Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Momentary BA9S Maintained Momentary E12 Maintained Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ALN29911DN ALN29920DN ALN29902DN ALN211DN ALN220DN ALN202DN AOLN29911DN AOLN29920DN AOLN29902DN AOLN211DN AOLN220DN AOLN202DN ALNE29911DN ALNE29920DN ALNE29902DN ALNE211DN ALNE220DN ALNE202DN AOLNE29911DN AOLNE29920DN AOLNE29902DN AOLNE211DN AOLNE220DN AOLNE202DN LSTD LSTD-6 LSTD LSTD-6 LETD LETD-6 LETD LETD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: PW: R: S: W: Y: amber green pure white (BA9S type only) red blue white yellow Use the white lens (W) for LED pure white illumination. Operating Voltage Code LED Transformer BA9S and E12 Types Specify an operating voltage code in place of in the Type No. 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). Dimensions M3.5 Terminal Screws 9 23.5 23 97.5 (2 blocks) 120.5 (4 blocks) * ALNE2/AOLNE2 E12/Full Voltage M3 Terminal Screw M3.5 Terminal Screw 77.5 (2 blocks) 100.5 (4 blocks) 22 9 20 M3.5 Terminal Screws Panel Thickness 0.8 to 7.5 o40 o35 o24 23 40 9 23.5 * ALNE2/AOLNE2 E12/Transformer Panel Thickness 0.8 to 7.5 5.5 o24 o40 40 40 23 112 (2 blocks) 135 (4 blocks) 9 20 o40 63 (2 blocks) 86 (4 blocks) Panel Thickness 0.8 to 7.5 o35 23 5.5 o35 o24 Panel Thickness 0.8 to 7.5 o40 M3.5 Terminal Screw o24 M3 Terminal Screw * ALN2/AOLN2 BA9S/Transformer o35 * ALN2/AOLN2 BA9S/Full Voltage 40 All dimensions in mm. o30 Series Illuminated Pushbuttons o30 Incandescent Round Extended Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Round Extended ALN ALNE Lamp Input Type Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer BA9S Maintained Momentary E12 Maintained Applicable Lamp Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Momentary AOLN AOLNE Contact ALN9911 ALN9920 ALN9902 ALN11 ALN20 ALN02 AOLN9911 AOLN9920 AOLN9902 AOLN11 AOLN20 AOLN02 ALNE9911 ALNE9920 ALNE9902 ALN11 ALN20 ALN02 AOLNE9911 AOLNE9920 AOLNE9902 AOLN11 AOLN20 AOLN02 LS (1W) LS-6 LS (1W) LS-6 LE (2W) LE-8 LE (2W) LE-8 * Color Code and Operating Voltage Code Lens Color Code Incandescent Illuminated Type Specify a lens color code in place of in the Type No. C: clear G: green O: orange R: red S: blue W: white Operating Voltage Code Incandescent Transformer BA9S Type Incandescent Transformer E12 Type Specify an operating voltage code in place of in the Type No. 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC 488: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). Dimensions 23 69.5 (2 blocks) 92.5 (4 blocks) 23 18.5 103.5 (2 blocks) 126.5 (4 blocks) 6 18.5 18.5 40 18.5 * AOLNE Maintained E12/Transformer Panel Thickness 0.8 to 7.5 23 18.5 125.5 (2 blocks) 148.5 (4 blocks) 36 M3.5 Terminal Screws o35 Panel Thickness 0.8 to 7.5 23 91.5 (2 blocks) 114.5 (4 blocks) 118.5 (2 blocks) 141.5 (4 blocks) 36 o35 o24.6 Panel Thickness 0.8 to 7.5 o35 o24.6 M3.5 Terminal Screw Panel Thickness M3 Terminal Screw 0.8 to 7.5 o35 M3.5 Terminal Screws M3.5 Terminal Screws 23 23 84.5 (2 blocks) 107.5 (4 blocks) * AOLNE Maintained E12/Full Voltage o35 o24.6 6 6 18.5 * ALNE Momentary E12/Transformer M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 Panel Thickness 0.8 to 7.5 o24.6 * ALNE Momentary E12/Full Voltage 96.5 (2 blocks) 119.5 (4 blocks) M3.5 Terminal Screw o35 23 18.5 M3 Terminal Screw o35 23 62.5 (2 blocks) 85.5 (4 blocks) M3 Terminal Screw Panel Thickness 0.8 to 7.5 o24.6 6 M3.5 Terminal Screws o24.6 Panel Thickness 0.8 to 7.5 * AOLN Maintained BA9S/Transformer * AOLN Maintained BA9S/Full Voltage o35 M3.5 Terminal Screw o24.6 M3 Terminal Screw * ALN Momentary BA9S/Transformer o24.6 * ALN Momentary BA9S/Full Voltage 40 18.5 23 o30 o30 Series Illuminated Pushbuttons LED Round Extended with Half Shroud Illuminated Pushbuttons Lamp Receptacle Shape Round Extended ALGN2 AOLGN2 ALGNE2 AOLGNE2 Operation Type Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Momentary BA9S Maintained Momentary E12 Maintained Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ALGN29911DN ALGN29920DN ALGN29902DN ALGN211DN ALGN220DN ALGN202DN AOLGN29911DN AOLGN29920DN AOLGN29902DN AOLGN211DN AOLGN220DN AOLGN202DN ALGNE29911DN ALGNE29920DN ALGNE29902DN ALGNE211DN ALGNE220DN ALGNE202DN AOLGNE29911DN AOLGNE29920DN AOLGNE29902DN AOLGNE211DN AOLGNE220DN AOLGNE202DN LSTD LSTD-6 LSTD LSTD-6 LETD LETD-6 LETD LETD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: PW: R: S: W: Y: amber green pure white (BA9S type only) red blue white yellow Use the white lens (W) for LED pure white illumination. Operating Voltage Code LED Transformer BA9S and E12 Types Specify an operating voltage code in place of in the Type No. 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). Dimensions * ALGN2/AOLGN2 BA9S/Full Voltage 40 59.5 (2 blocks) 27.5 82.5 (4 blocks) 94 (2 blocks) 117 (4 blocks) * ALGNE2/AOLGNE2 E12/Transformer o40 o35 o24 o40 o35 o27 Panel Thickness 0.8 to 3.5 23 23 74 (2 blocks) 97 (4 blocks) 24 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 3.5 o24 M3 Terminal Screw 40 27.5 o27 * ALGNE2/AOLGNE2 E12/Full Voltage 5.5 o24 o27 o35 o40 o27 o35 23 23 5.5 Panel Thickness 0.8 to 3.5 o40 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 3.5 o24 M3 Terminal Screw * ALGN2/AOLGN2 BA9S/Transformer 23.5 40 108.5 (2 blocks) 131.5 (4 blocks) 23.5 40 All dimensions in mm. o30 Series Illuminated Pushbuttons o30 Incandescent Round Extended with Half Shroud Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Round Extended ALNG ALNEG BA9S Lamp Input Type Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Contact 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Momentary E12 Type No. Momentary ALN9G911 ALN9G920 ALN9G902 ALN11 ALN20 ALN02 ALNE9G911 ALNE9G920 ALNE9G902 ALN11 ALN20 ALN02 Applicable Lamp LS (1W) LS-6 LE (2W) LE-8 * Color Code and Operating Voltage Code Lens Color Code Incandescent Illuminated Type Specify a lens color code in place of in the Type No. C: clear G: green O: orange R: red S: blue W: white Operating Voltage Code Incandescent Transformer BA9S Type Incandescent Transformer E12 Type Specify an operating voltage code in place of in the Type No. 1G6: 100/110V AC 1G8: 100/110V AC 11G6: 115V AC 11G8: 115V AC 12G6: 120V AC 12G8: 120V AC 2G6: 200/220V AC 2G8: 200/220V AC 23G6: 230V AC 23G8: 230V AC 24G6: 240V AC 24G8: 240V AC 38G6: 380V AC 38G8: 380V AC 4G6: 400/440V AC 4G8: 400/440V AC 48G6: 480V AC 48G8: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). Dimensions * ALNG Momentary BA9S/Full Voltage * ALNG Momentary BA9S/Transformer 92 (2 blocks) 115 (4 blocks) 23 99 (2 blocks) 122 (4 blocks) o27 36 36 36 o27 o35 o24.6 40 23 Panel Thickness 0.8 to 4 o35 M3.5 Terminal Screws Panel Thickness 0.8 to 4 23 65 (2 blocks) 88 (4 blocks) o35 * ALNEG Momentary E16/Transformer M3.5 Terminal Screw 6 40 23 o27 * ALNEG Momentary E16/Full Voltage M3 Terminal Screw o24.6 23 40 23 o24.6 58 (2 blocks) 81 (4 blocks) Panel Thickness 0.8 to 4 36 o27 o35 o24.6 23 6 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 4 M3 Terminal Screw 40 23 All dimensions in mm. 25 o30 o30 Series Illuminated Pushbuttons LED Round Extended with Full Shroud Illuminated Pushbuttons Lamp Receptacle Shape Round Extended ALFN2 AOLFN2 ALFNE2 AOLFNE2 Operation Type Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Momentary BA9S Maintained Momentary E12 Maintained Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ALFN29911DN ALFN29920DN ALFN29902DN ALFN211DN ALFN220DN ALFN202DN AOLFN29911DN AOLFN29920DN AOLFN29902DN AOLFN211DN AOLFN220DN AOLFN202DN ALFNE29911DN ALFNE29920DN ALFNE29902DN ALFNE211DN ALFNE220DN ALFNE202DN AOLFNE29911DN AOLFNE29920DN AOLFNE29902DN AOLFNE211DN AOLFNE220DN AOLFNE202DN LSTD LSTD-6 LSTD LSTD-6 LETD LETD-6 LETD LETD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: PW: R: S: W: Y: amber green pure white (BA9S type only) red blue white yellow Use the white lens (W) for LED pure white illumination. Operating Voltage Code LED Transformer BA9S and E12 Types Specify an operating voltage code in place of in the Type No. 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). Dimensions * ALFN2/AOLFN2 BA9S/Full Voltage 96 (2 blocks) 119 (4 blocks) o40 o35 o29.5 26 40 21 o40 Panel Thickness 0.8 to 6 23 111 (2 blocks) 134 (4 blocks) o40 M3.5 Terminal Screws Panel Thickness 0.8 to 6 23 76.5 (2 blocks) 99.5 (4 blocks) o35 * ALFNE2/AOLFNE2 E12/Transformer M3.5 Terminal Screw 5 40 25 o35 * ALFNE2/AOLFNE2 E12/Full Voltage M3 Terminal Screw o29.5 23 40 25 o29.5 61.5 (2 blocks) 84.5 (4 blocks) Panel Thickness 0.8 to 5.5 o40 o35 23 5.5 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 5.5 o29.5 M3 Terminal Screw * ALFN2/AOLFN2 BA9S/Transformer 40 21 All dimensions in mm. o30 Series Illuminated Pushbuttons o30 Incandescent Round Extended with Full Shroud Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Lamp Round Extended ALNF ALNEF Input Type Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Contact 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Momentary BA9S Maintained AOLNF AOLNEF Momentary E12 Maintained Applicable Lamp Type No. ALN9F911 ALN9F920 ALN9F902 ALN11 ALN20 ALN02 AOLN9F911 AOLN9F920 AOLN9F902 AOLN11 AOLN20 AOLN02 ALNE9F911 ALNE9F920 ALNE9F902 ALN11 ALN20 ALN02 AOLNE9F911 AOLNE9F920 AOLNE9F902 AOLN11 AOLN20 AOLN02 LS (1W) LS-6 LS (1W) LS-6 LE (2W) LE-8 LE (2W) LE-8 * Color Code and Operating Voltage Code Lens Color Code Incandescent Illuminated Type Specify a lens color code in place of in the Type No. C: clear G: green O: orange R: red S: blue W: white Operating Voltage Code Incandescent Transformer BA9S Type Incandescent Transformer E12 Type Specify an operating voltage code in place of in the Type No. 1F6: 100/110V AC 1F8: 100/110V AC 11F6: 115V AC 11F8: 115V AC 12F6: 120V AC 12F8: 120V AC 2F6: 200/220V AC 2F8: 200/220V AC 23F6: 230V AC 23F8: 230V AC 24F6: 240V AC 24F8: 240V AC 38F6: 380V AC 38F8: 380V AC 4F6: 400/440V AC 4F8: 400/440V AC 48F6: 480V AC 48F8: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). Dimensions 21 101 (2 blocks) 124 (4 blocks) 6 21 36 * AOLNF Maintained E12/Transformer M3.5 Terminal Screws Panel Thickness 0.8 to 5 23 21 123 (2 blocks) 146 (4 blocks) 36 Panel Thickness 0.8 to 5 23 89 (2 blocks) 112 (4 blocks) 40 21 o35 M3.5 Terminal M3 Terminal Screw Screw o35 o29.5 o35 o29.5 116 (2 blocks) 139 (4 blocks) o29.5 o35 o29.5 Panel Thickness 0.8 to 5 23 23 67 (2 blocks) 90 (4 blocks) M3.5 Terminal Screws 21 * AOLNEF Maintained E12/Full Voltage * ALNF Momentary E12/Transformer M3.5 Terminal Panel Thickness M3 Terminal Screw 0.8 to 5 Screw 6 82 (2 blocks) 105 (4 blocks) Panel Thickness 0.8 to 5 23 23 o35 * ALNEF Momentary E12/Full Voltage 6 21 M3.5 Terminal Screws o35 94 (2 blocks) 117 (4 blocks) Panel Thickness 0.8 to 5 o29.5 21 M3.5 Terminal Screw M3 Terminal Screw * ALONF Maintained BA9S/Transformer o35 23 23 60 (2 blocks) 83 (4 blocks) Panel Thickness 0.8 to 5 o29.5 6 M3.5 Terminal Screws * AOLNF Maintained BA9S/Full Voltage o35 M3.5 Terminal Screw Panel Thickness 0.8 to 5 o29.5 M3 Terminal Screw * ALNF Momentary BA9S/Transformer o29.5 * ALNF Momentary BA9S/Full Voltage 40 21 27 o30 o30 Series Illuminated Pushbuttons LED Mushroom (o40) Illuminated Pushbuttons Lamp Receptacle Shape o40 Mushroom ALN3 AOLN3 ALNE3 AOLNE3 Operation Type Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Momentary BA9S Maintained Momentary E12 Maintained Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ALN39911DN ALN39920DN ALN39902DN ALN311DN ALN320DN ALN302DN AOLN39911DN AOLN39920DN AOLN39902DN AOLN311DN AOLN320DN AOLN302DN ALNE39911DN ALNE39920DN ALNE39902DN ALNE311DN ALNE320DN ALNE302DN AOLNE39911DN AOLNE39920DN AOLNE39902DN AOLNE311DN AOLNE320DN AOLNE302DN LSTD LSTD-6 LSTD LSTD-6 LETD LETD-6 LETD LETD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: R: S: W: Y: amber green red blue white yellow Operating Voltage Code LED Transformer BA9S and E12 Types Specify an operating voltage code in place of in the Type No. 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). Dimensions * ALN3/AOLN3 BA9S/Full Voltage 23 97.5 (2 blocks) 120.5 (4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 23 77.5 (2 blocks) 100.5 (4 blocks) 40 20 M3.5 Terminal Screws Panel Thickness 0.8 to 7.5 36 o40 5.5 40 23.5 * ALNE3/AOLNE3 E12/Transformer * ALNE3/AOLNE3 E12/Full Voltage M3 Terminal Screw 36 36 23 40 23.5 23 112 (2 blocks) 135 (4 blocks) 36 63 (2 blocks) 86 (4 blocks) Panel Thickness 0.8 to 7.5 o40 5.5 M3.5 Terminal Screws o40 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o40 M3 Terminal Screw * ALN3/AOLN3 BA9S/Transformer 40 20 All dimensions in mm. 28 o30 Series Illuminated Pushbuttons o30 Incandescent Square and Rectangular Extended Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Lamp Square Extended ULQN Input Type Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Momentary BA9S UOLQN Maintained Rectangular (Marking Type) ULQNB Momentary BA9S UOLQNB Maintained Contact Applicable Lamp Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ULQN9911 ULQN9920 ULQN9902 ULQN11 ULQN20 ULQN02 UOLQN9911 UOLQN9920 UOLQN9902 UOLQN11 UOLQN20 UOLQN02 ULQN9B911 ULQN9B920 ULQN9B902 ULQN11 ULQN20 ULQN02 UOLQN9B911 UOLQN9B920 UOLQN9B902 UOLQN11 UOLQN20 UOLQN02 LS (1W) LS-6 LS (1W) LS-6 LS (1W) LS-6 LS (1W) LS-6 * Color Code and Operating Voltage Code Lens Color Code Incandescent Illuminated Type Specify a lens color code in place of in the Type No. C: clear (square type only) G: green O: orange R: red S: blue W: white Clear lens is not available for the rectangular type. Operating Voltage Code Incandescent Transformer Incandescent Transformer Square Extended Type Rectangular Marking Type Specify an operating voltage code in place of in the Type No. 16: 100/110V AC 1B6: 100/110V AC 116: 115V AC 11B6: 115V AC 126: 120V AC 12B6: 120V AC 26: 200/220V AC 2B6: 200/220V AC 236: 230V AC 23B6: 230V AC 246: 240V AC 24B6: 240V AC 386: 380V AC 38B6: 380V AC 46: 400/440V AC 4B6: 400/440V AC 486: 480V AC 48B6: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC). Dimensions 25 98 (2 blocks) 121 (4 blocks) 6 25 120 (2 blocks) 143 (4 blocks) 36 52.2 40 20 44 * UOLQNB Maintained BA9S/Transformer Panel Thickness 0.8 to 3.2 52.2 30x36 36.4x42.4 M3.5 Terminal Screws 36.4x42.4 Panel Thickness 0.8 to 3.2 23 23 86 (2 blocks) 109 (4 blocks) 34 25 20 * UOLQNB Maintained BA9S/Full Voltage M3.5 Terminal Screw 14 23 14 M3 Terminal Screw Panel Thickness 0.8 to 3.2 M3.5 Terminal Screws 34 25 23 86 (2 blocks) 109 (4 blocks) Panel Thickness 0.8 to 3.2 23 23 64 (2 blocks) 87 (4 blocks) M3.5 Terminal Screws 36.4x42.4 30x36 6 6 20 * ULQNB Momentary BA9S/Transformer M3.5 Terminal Screws Panel Thickness 0.8 to 3.2 Panel Thickness 0.8 to 3.2 34 25 98 (2 blocks) 121 (4 blocks) * ULQNB Momentary BA9S/Full Voltage M3 Terminal Screw 14 23 14 20 M3.5 Terminal Screws M3 Terminal Screw 36.4x42.4 23 64 (2 blocks) 87 (4 blocks) Panel Thickness 0.8 to 3.2 30x36 25 6 M3.5 Terminal Screws 34 M3.5 Terminal Screw Panel Thickness 0.8 to 3.2 M3 Terminal Screw * UOLQN Maintained BA9S/Transformer * UOLQN Maintained BA9S/Full Voltage * ULQN Momentary BA9S/Transformer 30x36 * ULQN Momentary BA9S/Full Voltage 25 120 (2 blocks) 143 (4 blocks) 25 44 29 o30 o30 Series Illuminated Pushbuttons Incandescent Push Turn Lock Switches Lamp Receptacle Shape Operation Type Lamp Input Type ALNL Without Lamp BA9S Contact Type No. 1NO-1NC ALN9L911 2NO ALN9L920 2NC ALN9L902 Full Voltage Applicable Lamp LS (1W) Push Turn Lock Incandescent 1NO-1NC ALN11 2NO ALN20 2NC ALN02 Transformer LS-6 * Color Code and Operating Voltage Code Lens Color Code Specify a lens color code in place of in the Type No. G: green O: orange R: red S: blue W: white Operating Voltage Code Specify an operating voltage code in place of in the Type No. 1L6: 100/110V AC 11L6: 115V AC 12L6: 120V AC 2L6: 200/220V AC 23L6: 230V AC 24L6: 240V AC 38L6: 380V AC 4L6: 400/440V AC 48L6: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC). * Push Turn Lock: Knob is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise. Dimensions * ALNL BA9S/Transformer 6 23 67 (2 blocks) 90 (4 blocks) 23 101 (2 blocks) 124 (4 blocks) 36 36 o35 40 25 Panel Thickness 0.8 to 5 o22 M3.5 Terminal Screws M3.5 Terminal Screw Panel Thickness 0.8 to 5 o22 M3 Terminal Screw o35 * ALNL BA9S/Full Voltage 40 25 All dimensions in mm. 30 o30 Series Illuminated Pushbuttons o30 LED Pushlock Turn Reset / Push Turn Lock Types Lamp Receptacle Shape o40 Mushroom Pushlock Turn Reset AVLN3 AVLNE3 Operation Type Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Pushlock Turn Reset BA9S Pushlock Turn Reset E12 o40 Mushroom Push Turn Lock AJLN3 Without Lamp Full Voltage Push Turn Lock BA9S LED Transformer Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC AVLN39911DNR AVLN39920DNR AVLN39902DNR AVLN311DNR AVLN320DNR AVLN302DNR AVLNE39911DNR AVLNE39920DNR AVLNE39902DNR AVLNE311DNR AVLNE320DNR AVLNE302DNR 1NO-1NC AJLN39911DN 2NO AJLN39920DN 2NC AJLN39902DN 1NO-1NC AJLN311DN 2NO AJLN320DN 2NC AJLN302DN LSTD LSTD-6 LETD LETD-6 LSTD LSTD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: R: W: Y: Operating Voltage Code LED Transformer BA9S Types Specify an operating voltage code in place of in the Type No. amber green red white yellow 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). * Pushlock Turn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only. Note: AVNL3 and AVNLE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Lens is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise. Dimensions 23.5 97.5 (2 blocks) 120.5 (4 blocks) 5.5 23.5 M3.5 Terminal Screws 20 112 (2 blocks) 135 (4 blocks) 40 20 Panel Thickness 0.8 to 7.5 L PU o40 97.5 (2 blocks) 120.5 (4 blocks) CK o40 S O 23 23.5 23 23 77.5 (2 blocks) 100.5 (4 blocks) H 23 Panel Thickness 0.8 to 7.5 36 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 63 (2 blocks) 86 (4 blocks) M3.5 Terminal Screws * AJLN3 BA9S/Transformer * AJLN3 BA9S/Full Voltage 5.5 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o40 23 23 63 (2 blocks) 86 (4 blocks) M3 Terminal Screw 36 Panel Thickness 0.8 to 7.5 * AVLNE3 E12/Transformer o40 M3.5 Terminal Screws o40 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 5.5 * AVLNE3 E12/Full Voltage * AVLN3 BA9S/Transformer o40 * AVLN3 BA9S/Full Voltage 40 23.5 All dimensions in mm. 31 o30 o30 Series Illuminated Pushbuttons Incandescent Pushlock Turn Reset / Push Turn Lock Types Lamp Receptacle Shape o40 Mushroom Pushlock Turn Reset AVLN3 AVLNE3 Operation Type Lamp Input Type Without Lamp Full Voltage Incandescent Transformer Without Lamp Full Voltage Incandescent Transformer Pushlock Turn Reset BA9S Pushlock Turn Reset E12 o40 Mushroom Push Turn Lock AJLN3 Without Lamp Full Voltage Push Turn Lock BA9S Incandescent Transformer Contact Applicable Lamp Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC AVLN39911NR AVLN39920NR AVLN39902NR AVLN311NR AVLN320NR AVLN302NR AVLNE39911NR AVLNE39920NR AVLNE39902NR AVLNE311NR AVLNE320NR AVLNE302NR 1NO-1NC AJLN39911N 2NO AJLN39920N 2NC AJLN39902N 1NO-1NC AJLN311N 2NO AJLN320N 2NC AJLN302N LS (1W) LS-6 LE (2W) LE-8 LS (1W) LS-6 * Color Code and Operating Voltage Code Lens Color Code Incandescent Illuminated Type Specify a lens color code in place of in the Type No. G: green O: orange R: red Operating Voltage Code Incandescent Transformer BA9S Type Incandescent Transformer E12 Type Specify an operating voltage code in place of in the Type No. 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC 488: 480V AC * Full voltage types do not contain a lamp. Order incandescent lamps separately. For lamps, see page 63. * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). * Pushlock Turn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only. Note: AVNL3 and AVNLE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Lens is maintained when turned clockwise in the depressed position and is reset when turned counterclockwise. Dimensions 23.5 97.5 (2 blocks) 120.5 (4 blocks) 5.5 23.5 M3.5 Terminal Screws 112 (2 blocks) 135 (4 blocks) 40 20 L PU o40 97.5 (2 blocks) 120.5 (4 blocks) CK o40 S O 32 20 Panel Thickness 0.8 to 7.5 23 23.5 23 23 77.5 (2 blocks) 100.5 (4 blocks) H 23 Panel Thickness 0.8 to 7.5 36 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 63 (2 blocks) 86 (4 blocks) M3.5 Terminal Screws * AJLN3 BA9S/Transformer * AJLN3 BA9S/Full Voltage 5.5 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o40 23 23 63 (2 blocks) 86 (4 blocks) M3 Terminal Screw 36 Panel Thickness 0.8 to 7.5 * AVLNE3 E12/Transformer o40 M3.5 Terminal Screws o40 M3.5 Terminal M3 Terminal Screw Panel Thickness Screw 0.8 to 7.5 5.5 * AVLNE3 E12/Full Voltage * AVLN3 BA9S/Transformer o40 * AVLN3 BA9S/Full Voltage 40 23.5 All dimensions in mm. o30 Series Selector Switches o30 No. of Positions ASN Selector Switches (Knob Operator Type) Shape ASN 3 10 (1NO) 11 (1NO-1NC) 20 (2NO) 90 2-position * Knob: Black * Round bezel (metal): Chrome-plated * Units marked with differ in shape. See page 36 for dimensions. * Nameplates are ordered separately. 2 1 Contact Arrangement Chart Contact Code (ASN) 22 (2NO-2NC) 7S (1NO-1NC) 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) 7S (1NO-1NC) Contact Code (ASN) 11 (1NO-1NC) 22 (2NO-2NC) 5S (2NO-2NC) 45 3-position 4 7S (2NC) 8S (4NC) 11 (1NO-1NC) 22 (2NO-2NC) 5S (2NO-2NC) 7S (2NC) 8S (4NC) Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 Type Operator Position L Maintained L R NO Dummy NO NC NO NO NO NC NO NC NO NC NO R Spring Return from Right L ASN310 ASN410 ASN311 ASN411 ASN320 ASN420 R ASN322 ASN422 ASN37S ASN47S NO NC NO NO NO NC NO NC NO NC -- Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC NO NC NO NC NO NC NO NC NO NC NC NC NC NC NC NC R L Operator Position L C R Maintained L -- ASN3010 ASN4010 ASN3011 ASN4011 ASN3020 ASN4020 ASN3022 ASN4022 ASN307S ASN407S Spring Return from Left Maintained R L ASN111 ASN211 ASN122 ASN222 ASN15S ASN25S ASN17S ASN27S ASN18S ASN28S -- Spring Return from Right C C C R -- R -- C Mounting Position L Spring Return from Left -- Dummy Contact Block Maintained R L -- R L -- ASN1011 ASN2011 ASN1022 ASN2022 ASN105S ASN205S ASN107S ASN207S ASN108S ASN208S 33 o30 o30 Series Selector Switches No. of Positions ASN Selector Switches (Lever Operator Type) Shape ASNL 3 10 (1NO) 11 (1NO-1NC) 20 90 2-position (2NO) 22 (2NO-2NC) 7S (1NO-1NC) 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) 7S (1NO-1NC) Contact Code (ASN) 11 (1NO-1NC) 22 (2NO-2NC) 5S (2NO-2NC) 45 3-position * Lever: Black * Round bezel (metal): Chrome-plated * Units marked with differ in shape. See page 36 for dimensions. * Nameplates are ordered separately. 2 1 Contact Arrangement Chart Contact Code (ASN) 7S (2NC) 8S (4NC) 11 (1NO-1NC) 22 (2NO-2NC) 5S (2NO-2NC) 7S (2NC) 8S (4NC) 34 4 Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 Type Operator Position L Maintained L R NO Dummy NO NC NO NO NO NC NO NC NO NC NO R Spring Return from Right L R ASN3L10 ASN4L10 ASN3L11 ASN4L11 ASN3L20 ASN4L20 ASN3L22 ASN4L22 ASN3L7S ASN4L7S Dummy NO NC NO NO NO NC NO NC NO NC Contact Block -- Operator Position Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NC NO NC NO NC NO NO NC NC NC NC NC NC NC NC NO NC NO NC NO NC NO NC NO NC NC NC NC NC NC NC L C R Maintained Spring Return from Left L R -- ASN30L10 ASN40L10 ASN30L11 ASN40L11 ASN30L20 ASN40L20 ASN30L22 ASN40L22 ASN30L7S ASN40L7S Maintained ASN2L11 ASN1L22 ASN2L22 ASN1L5S ASN2L5S ASN1L7S ASN2L7S ASN1L8S ASN2L8S -- Spring Return from Right C C R L ASN1L11 -- R -- C R L L Spring Return from Left -- C Mounting Position Maintained R L R L -- -- ASN10L11 ASN20L11 ASN10L22 ASN20L22 ASN10L5S ASN20L5S ASN10L7S ASN20L7S ASN10L8S ASN20L8S o30 Series Selector Switches o30 ASN Key Selector Switches Shape * Cylinder: Chrome-plated * Round bezel (metal): Chrome-plated * On the spring-returned types, the keys can be released only from the maintained position. On the maintained types, the key can be released from every position. Key retained positions are also available. See page 12. * Key selector switch is supplied with two standard keys. Two different keys are available upon request. * Nameplates are ordered separately. No. of Positions ASNK 4 2 3 1 Contact Arrangement Chart Contact Code (ASN) 10 (1NO) 11 (1NO-1NC) 20 90 2-position (2NO) 22 (2NO-2NC) 7S (1NO-1NC) 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) 7S (1NO-1NC) Contact Code (ASN) 11 (1NO-1NC) 22 (2NO-2NC) 5S 45 3-position (1NO-1NC) (1NO-1NC) 7S (1NO-1NC) 8S (2NO-2NC) 11 (1NO-1NC) 22 (2NO-2NC) 5S (1NO-1NC) (1NO-1NC) 7S (1NO-1NC) 8S (2NO-2NC) Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 1 2 1 2 1 2 1 2 1 2 3 4 1 2 Type Operator Position L Maintained L R NO Dummy NO NC NO NO NO NC NO NC NO NC NO R Spring Return from Right L R ASN3K10 ASN4K10 ASN3K11 ASN4K11 ASN3K20 ASN4K20 ASN3K22 ASN4K22 ASN3K7S ASN4K7S Dummy NO NC NO NO NO NC NO NC NO NC Contact Block -- Operator Position Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC NO NC L C R Maintained Spring Return from Left L R -- ASN30K10 ASN40K10 ASN30K11 ASN40K11 ASN30K20 ASN40K20 ASN30K22 ASN40K22 ASN30K7S ASN40K7S Maintained ASN2K11 ASN1K22 ASN2K22 ASN1K5S ASN2K5S ASN1K7S ASN2K7S ASN1K8S ASN2K8S -- Spring Return from Right C C R L ASN1K11 -- R -- C R L L Spring Return from Left -- C Mounting Position Maintained R L R L -- -- ASN10K11 ASN20K11 ASN10K22 ASN20K22 ASN10K5S ASN20K5S ASN10K7S ASN20K7S ASN10K8S ASN20K8S 35 o30 o30 Series Selector Switches Dimensions * Knob Operator Type Dimensions of knob operator type marked with 90 6 23 45 23 6 40 54 (1 or 2 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 36 o35 45 45 40 58 (1 or 2 blocks) 22 77 (4 blocks) 36 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 22 81 (4 blocks) * Lever Operator Type Dimensions of lever operator type marked with Panel Thickness 0.8 to 7.5 36 o35 23 6 58 (1 or 2 blocks) 81 (4 blocks) 40 27 77 (4 blocks) 25.0 23 54 (1 or 2 blocks) 25.0 6 M3.5 Terminal Screw 45 45 45 36 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 90 40 26.5 * Key Selector Type 45 36 24.5 6 90 45 o35 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 23 54 (1 or 2 blocks) 40 22 22 77 (4 blocks) All dimensions in mm. * Contact Block Mounting Position and Contact Arrangement Chart Center Left 4 3 36 1 2 L 1 2 3 4 NO NO NC NC C Right R Operator Position o30 Series Selector Switches o30 90 2-position No. of Positions ASTN Selector Switches (Knob Operator Type) ASTN Shape Contact Arrangement Chart Contact Block Contact Code (ASTN) Mounting Position Type 1 2 1 2 3 4 NO NC NO NO NC NC 11 (1NO-1NC) 22 (2NO-2NC) Contact Block Contact Code (ASTN) Maintained Operator Position L L R R Spring Return from Right L ASTN4211 ASTN3222 ASTN4222 Maintained Operator Position Type 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC (2NO-2NC) 22 (2NO-2NC) 40 (4NC) 22 (2NO-2NC) 20 (2NO) 40 (4NO) 11 (1NO-1NC) 22 (2NO-2NC) 11 (1NO-1NC) L C -- -- -- -- -- Spring Return from Left Spring Return from Right Spring Return Two-way R L R L R L C C C R L R -- R ASTN3211 C Mounting Position 22 45 3-position * Knob operator: Black * Round bezel (metal): Chrome-plated ASTN1122 ASTN2122 ASTN20122 ASTN5122 ASTN1222 ASTN2222 ASTN20222 ASTN5222 ASTN1340 -- ASTN1422 -- ASTN20422 -- ASTN1520 -- ASTN20520 -- ASTN1540 -- ASTN20540 -- ASTN1611 -- -- -- ASTN1622 -- -- -- -- -- -- ASTN5111 -- -- Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. 4 * Dimensions M3.5 Terminal Screw Center Left Panel Thickness 0.8 to 7.5 Right L 3 1 1 2 3 4 NO NO NC NC C R Operator Position 45 o35 2 90 45 6 36 * Contact Block Mounting Position and Contact Arrangement Chart 23 58 (2 blocks) 81 (4 blocks) 40 27 37 o30 o30 Series Selector Switches 90 2-position No. of Positions ASTN Selector Switches (Lever Operator Type) Shape Contact Arrangement Chart Contact Code (ASTN) Contact Block Mounting Position Type 1 2 1 2 3 4 NO NC NO NO NC NC 11 (1NO-1NC) 22 (2NO-2NC) Contact Code (ASTN) Contact Block Maintained Operator Position L L R R Spring Return from Right L ASTN42L11 ASTN32L22 ASTN42L22 Maintained Operator Position Type 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC (2NO-2NC) 22 (2NO-2NC) 40 (4NC) 22 (2NO-2NC) 20 (2NO) 40 (4NO) 11 (1NO-1NC) 22 (2NO-2NC) 11 (1NO-1NC) L C -- -- -- -- -- Spring Return from Left Spring Return from Right Spring Return Two-way C C C R L R -- R ASTN32L11 C Mounting Position 22 45 3-position * Lever operator: Black * Round bezel (metal): Chrome-plated ASTNL ASTN11L22 ASTN21L22 ASTN201L22 ASTN51L22 ASTN12L22 ASTN22L22 ASTN202L22 ASTN52L22 ASTN13L40 -- ASTN14L22 -- ASTN204L22 -- ASTN15L20 -- ASTN205L20 -- ASTN15L40 -- ASTN205L40 -- ASTN16L11 -- -- -- ASTN16L22 -- -- -- -- -- -- -- -- ASTN51L11 Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. Center 38 1 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 1 2 3 4 NO NO NC NC C R Operator Position 90 45 45 o35 2 L 3 Right 6 23 58 (1 or 2 blocks) 81 (4 blocks) 25.0 4 * Dimensions 29 36 * Contact Block Mounting Position and Contact Arrangement Chart Left R L R L R L 40 o30 Series Selector Switches o30 90 2-position No. of Positions ASTN Key Selector Switches Shape Contact Arrangement Chart Contact Code (ASTN) Contact Block Mounting Position Type 1 2 1 2 3 4 NO NC NO NO NC NC 11 (1NO-1NC) 22 (2NO-2NC) Contact Code (ASTN) Contact Block L Spring Return from Right Maintained Operator Position L R L R ASTN42K11 ASTN32K22 ASTN42K22 Spring Return from Left Maintained Operator Position Type 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 1 2 3 4 1 2 1 2 3 4 1 2 NO NO NC NC NO NO NC NC NO NO NO NO NO NC NC NO NO NO NO NO NO NO NC NO NC NO NC NO NO NC (2NO-2NC) 22 (2NO-2NC) 40 (4NC) 22 (2NO-2NC) 20 (2NO) 40 (4NO) 11 (1NO-1NC) 22 (2NO-2NC) 11 (1NO-1NC) L C -- -- -- -- -- Spring Return from Right Spring Return Two-way R L R L R L C C C R L R -- R ASTN32K11 C Mounting Position 22 45 3-position * Cylinder: Chrome-plated * Round bezel (metal): Chrome-plated * On the spring-returned types, the keys can be released only from the maintained position. * On the maintained types, the key can be released from every position. Key retained positions are also available. See page 12. ASTNK ASTN11K22 ASTN21K22 ASTN201K22 ASTN51K22 ASTN12K22 ASTN22K22 ASTN202K22 ASTN52K22 ASTN13K40 -- ASTN14K22 -- ASTN204K22 -- ASTN15K20 -- ASTN205K20 -- ASTN15K40 -- ASTN205K40 -- ASTN16K11 -- -- -- ASTN16K22 -- -- -- -- -- -- -- -- ASTN51K11 Notes: 1. The operator of the 2-way spring return unit may slightly deviate from the center position. 2. Turn the operator to each position accurately. * Contact Block Mounting Position and Contact Arrangement Chart Center 1 Panel Thickness 0.8 to 7.5 2 1 2 3 4 NO NO NC NC C 45 45 Right R Operator Position 6 40 Left L 3 M3.5 Terminal Screw o35 4 * Dimensions 23 57 (1 or 2 blocks) 80 (4 blocks) 16.5 40 38 39 o30 o30 Series Illuminated Selector Switches Illuminated Selector Switches 90 2-position Shape ASLN (Base BA9S) Contact Arrangement Chart Contact Code Contact Block Maintained Operator Position Lamp Input Type L Spring Return from Right L R Spring Return from Left R L R Mounting Position Type 1 NO Without Lamp Full Voltage ASLN29911N ASLN219911N ASLN229911N 2 NC LED Transformer ASLN211DN ASLN2111DN ASLN2211DN Incandescent Transformer ASLN211N ASLN2111N ASLN2211N 11 (1NO-1NC) 20 (2NO) 22 R 1 NO Without Lamp Full Voltage ASLN29920N ASLN219920N ASLN229920N 2 NO LED Transformer ASLN220DN ASLN2120DN ASLN2220DN Incandescent Transformer ASLN220N ASLN2120N ASLN2220N Without Lamp Full Voltage ASLN29922N ASLN219922N ASLN229922N LED Transformer ASLN222DN ASLN2122DN ASLN2222DN Incandescent Transformer ASLN222N ASLN2122N ASLN2222N 1 2 3 4 (2NO-2NC) L NO NC NO NC * Color Code and Operating Voltage Code LED Illuminated Type Lens/LED Color Code Specify a lens/LED color code in place of in the Type No. A: G: R: S: W: Y: amber green red blue white yellow Incandescent Illuminated Type Operating Voltage Code Lens Color Code Specify a lens color code in place of Specify an operating voltage code in place of in the Type No. in the Type No. 16: 100/110V AC A: amber 156: 115V AC G: green 136: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 256: 240V AC 386: 380V AC 46: 400/440V AC 486: 480V AC (incandescent only) * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer type contains an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] * Contact Block Mounting Position and Contact Arrangement Chart * Dimensions 3 1 40 L 1 2 3 4 NO NO NC NC R Operator Position 5.5 45 40 23 63 (2 blocks) 9 A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) 90 4 5 o40 2 Right Panel Thickness 0.8 to 7.5 (including nameplate) o25 4 Left M3 Terminal Screw o35 M3.5 Terminal Screws 28 A: Full voltage type B: Transformer type o30 Series Illuminated Selector Switches o30 Illuminated Selector Switches 45 3-position Contact Code Contact Block Mounting Position Type 1 NO 2 NO 20 (2NO) 02 (2NC) 22 (2NO-2NC) 40 (4NO) 04 (4NC) 1 NC 2 NC 1 2 3 4 NO NO NC NC 1 2 3 4 NO NO NO NO 1 2 3 4 NC NC NC NC Maintained Operator Position L C Lamp Input Type R Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Spring Return from Right C L Spring Return from left C R C C R L Spring Return Two-way L R L R ASLN39920N ASLN319920N ASLN329920N ASLN339920N ASLN320DN ASLN3120DN ASLN3220DN ASLN3320DN ASLN320N ASLN3120N ASLN3220N ASLN3320N ASLN39902N ASLN319902N ASLN329902N ASLN339902N ASLN302DN ASLN3102DN ASLN3202DN ASLN3302DN ASLN302N ASLN3102N ASLN3202N ASLN3302N ASLN39922N ASLN319922N ASLN329922N ASLN339922N ASLN322DN ASLN3122DN ASLN3222DN ASLN3322DN ASLN322N ASLN3122N ASLN3222N ASLN3322N ASLN39940N ASLN319940N ASLN329940N ASLN339940N ASLN340DN ASLN3140DN ASLN3240DN ASLN3340DN ASLN340N ASLN3140N ASLN3240N ASLN3340N ASLN39904N ASLN319904N ASLN329904N ASLN339904N ASLN304DN ASLN3104DN ASLN3204DN ASLN3304DN ASLN304N ASLN3104N ASLN3204N ASLN3304N * Color Code and Operating Voltage Code LED Illuminated Type Lens/LED Color Code Specify a lens/LED color code in place of in the Type No. A: G: R: S: W: Y: amber green red blue white yellow Incandescent Illuminated Type Operating Voltage Code Lens Color Code Specify a lens color code in place of Specify an operating voltage code in place of in the Type No. in the Type No. 16: 100/110V AC A: amber 156: 115V AC G: green 136: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 256: 240V AC 386: 380V AC 46: 400/440V AC 486: 480V AC (incandescent only) * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). * Contact Block Mounting Position and Contact Arrangement Chart * Dimensions M3.5 Terminal Screws 1 M3 Terminal Screw Panel Thickness 0.8 to 7.5 (including nameplate) 90 4 5 45 1 2 3 4 NO NO NC NC R Operator Position 5.5 40 23 63 (2 blocks) 9 A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) o40 C o35 2 L 3 Right o25 4 Center Left 28 A: Full Voltage type B: Transformer type 41 o30 o30 Series Selector Pushbuttons Ring Operator Type / Lever Operator Type Selector Pushbuttons Ring/Lever Contact Circuit Code Code Shape Contact Block Ring Operator Lever Operator Type No. Type No. Button Color Code Pushbutton Mounting Type Normal Position ABN A 11 (1NO-1NC) I G 20 Ring Operator (90 2-position) 6 23 25 41 D Panel Thickness 0.8 to 7.5 (including namplate) B 40 o28 o35 M3.5 Terminal Screw (2NO) 40 Panel Thickness 0.8 to 7.5 (including namplate) M3.5 Terminal Screw 23 6 23 25 41 40 o28 o35 C 40 ABNL I 22 (2NO-2NC) D Lever Operator (90 2-position) 26 41 40 o35 50 6 23 40 40 o35 26 41 50 23 F Panel Thickness 0.8 to 7.5 (including namplate) M3.5 Terminal Screw 6 23 E Panel Thickness 0.8 to 7.5 (including namplate) M3.5 Terminal Screw H 40 1 2 1 2 1 2 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 NO NC NC NO NO NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO Push Normal Blocked Push ABN6111 ABN6L111 ABN6411 ABN6L411 ABN9111 ABN9L111 ABN7120 Blocked ABN6122 ABN6L122 ABN6222 ABN6L222 ABN6422 ABN6L422 ABN7122 ABN7L122 ABN7222 ABN7L222 ABN7322 ABN7L322 ABN9122 ABN9L122 B: G: R: Y: black green red yellow * Specify a button color code in place of in the Type No. * Ring/Lever (metal): Chrome-plated Notes 1. Circuit Codes A, B, C, and I: When the ring or lever operator is turned, the button is pushed in. 2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button. 3. Circuit Codes G and H: The pushbutton does not operate when the ring or lever operator is turned to the left position. 4. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure may be caused. * Contact Block Mounting Position and Contact Arrangement Chart 3 1 42 Normal 1 2 3 4 Push 50 Ring Operator 80 2 50 4 * Mounting Hole Layout 80 Lever Operator o30 ARN/ARNS Series Mono-lever Switches Single lever offers up to four directions of control Mono-lever switches operate in four directions using a single lever. Switch contacts are actuated in the direction in which the lever is pushed, enabling quick and accurate control in any desired direction. Ideal for machine tools and industrial machines. The lever action can be maintained or springreturned in any combination. Also available with interlock mechanism to prevent inadvertent actuation. Specifications and Ratings Contact Ratings Contact Block Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 Type BR 600V 10A AC-15 (A600) DC-13 (P600) Characteristics * Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V 10A 10A 10A 4A 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Specifications Double-break slow action Each contact block contains two independent contacts (2NO, 1NO-1NC, or 2NC) Up to four contact blocks can be mounted Insulation Resistance 100 M minimum (500V DC megger) Dielectric Strength Between live and dead parts: 2,500V AC, 1 minute Mechanical Life 500,000 operations minimum (Interlocking type: 250,000 operations minimum) Electrical Life Operating Temperature -25 to +50C (no freezing) Operating Humidity 45 to 85% RH (no condensation) Lever Knob Black Contact Arrangement BR Contact Block Control Mechanism The contact block is made of nylon resin. Each contact block contains two pairs of double-break silver contacts. There are three types as shown in the diagram below and up to four contact blocks can be mounted in any direction. A wide variety of circuits allows diverse combinations of control. When the operator lever is pushed to about 30 in each direction from the neutral position, the contact in that direction activates.The lever can operate in two, three, or four directions, and combinations of maintained or spring-return from any position are possible. BR-1E (2NO) BR-2E (1NO-1NC) BR-3E (2NO) 43 Modified March 11, 2005 5:32 pm o30 ARN/ARNS Series Mono-lever Switches Types 2-position (Left-Right) Dimensions (mm) Maintained ARN2-1010-B Spring return ARN2-2020-B Maintained ARN2-0101-B Spring return ARN2-0202-B Maintained ARN4-1111-B Spring return ARN4-2222-B Maintained ARNS2-1010-B Spring return ARNS2-2020-B Maintained ARNS2-0101-B Spring return ARNS2-0202-B Maintained ARNS4-1111-B Spring return ARNS4-2222-B Maintained ARNL2-1010-B Spring return ARNL2-2020-B Maintained ARNL2-0101-B Spring return ARNL2-0202-B 6 Maintained ARNL4-1111-B 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 Spring return ARNL4-2222-B M3.5 Terminal Screw Panel Thickness 0.8 to 6 30 Type No. 51 o22 2-position (Up-Down) Lever Action o42 Position 30 Operator Type ARN (Long Lever Type) 6 23 83 2-position (Left-Right) Panel Thickness 0.8 to 6 30 M3.5 Terminal Screw 51 30 2-position (Up-Down) o42 ARNS (Short Lever Type) Minimum horizontal/vertical mounting centers: 110 o22 4-position (Up-Down-Left-Right) 51 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 6 23 63 2-position (Left-Right) Panel Thickness 0.8 to 6 51 M3.5 Terminal Screw 0 o22 3 2-position (Up-Down) 30 ARNL (Interlocking Type) Minimum horizontal/vertical mounting centers: 70 o42 4-position (Up-Down-Left-Right) 51 1 block: 47, 2 blocks: 70 3 blocks: 93, 4 blocks: 116 23 51 83 4-position (Up-Down-Left-Right) The operator lever is locked only in the center position. Minimum horizontal/vertical mounting centers: 110 * Specify Contact Arrangement from the table below in place of . * Terminal covers are ordered separately. * Panel Cut-Out o3 R0.8 max. 4.8 +0.2 0 0.5 + 0 0.5 33 +0.5 0 Right 0 Up * Mono-Lever with Terminal Cover 68 31 * Lever Operator Position 31 68 Left 23 64 Down Ordering Information No. of Contact Blocks Type ARN ARNS ARNL 1: 2: 3: 4: 1 block 2 blocks 3 blocks 4 blocks Lever Action Right Down Left Contact Arrangement Order of Entry: UpRight DownLeft Order of Entry: UpRight DownLeft 1: Maintained 2: Spring return 0: Blocked 10: 1NO 01: 1NC 11: 1NO-1NC 20: 2NO 02: 2NC 00: Blocked Lever Knob Color 1 2 B: black 3 4 1 3 5 7 9 11 13 15 Lever Operation Mode 1: Maintained 2: Spring return 0: Blocked 1 0 1 NO - - - - NC - NO - - - - NO - - - - NC - NC - - - - 2 - - - NO - - - NC Terminal No. Up Terminal No. [Example] ARN 4 - 1012 - 2 0 0 0 0 2 1 1 - B Contact Block Position Direction of Lever Operation When ordering, specify items to according to the following example. 2 4 6 8 10 12 14 16 Contact Block Type BR-2E BR-1E BR-2E BR-3E : Contacts marked with do not operate. * To calculate the number of contact blocks required, add the number of NO and NC contacts on each pair of adjoining positions (up + right, right + down, down + left, and left + up). The largest of the four sums is the number of contact blocks required. Up to four contact blocks can be mounted. * When UL and CSA markings are required on the mono-lever switch, specify as shown below. [Example] ARN4-1012-20000211-B- U 44 Modified March 11, 2005 5:32 pm ARN/ARNS Series Mono-lever Switches o30 Accessories and Maintenance Parts Shape Specification Type No. Ordering Type No. Package Quantity Description 70 70 0. o3 Nameplate 5 MLO 1 Chrome-plated brass (matte surface) MLO MLOPN10 10 ARN-VL2 ARN-VL2 1 * Terminal covers are ordered separately. When ordering, specify the Type No. and the required quantity. * Order 2 pieces for each contact block. BR-1E BR-1E 1 * 2NO contact BR-2E BR-2E 1 * 1NO-1NC contact BR-3E BR-3E 1 * 2NC contact Bellows ARN-BL ARN-BL 1 * For ARN/ARNS (Locking ring not included) Bellows (Interlocking Type) ARNL-BL ARNL-BL 1 * For ARNL (Locking ring not included) 1 Specify a color code in place of . B (black), G (green), R (red) * For ARN/ARNS Terminal Cover Contact Block (BR Type) Knob ARNB- ARNB- 45 o30/o25 CS Series Cam Switches 76 standard circuits to choose from * Wide variety of heavy-duty oiltight cam switches * Operators available up to 12 positions * Switches made with a double-pole contact block * Contact blocks rated at 600V, 10A * Ideal for ammeter/voltmeter applications * UL listed and CSA approved (except ACSSO and ACSSK) Specifications and Ratings Contact Ratings Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 600V 10A AC-15 (A600) DC-13 (P600) Characteristics * Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V -- -- 8A 5A 110V 10A 5A 3A 1.2A Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Specifications Contact Arrangement Operation Angle Operator Positions Insulation Resistance Dielectric Strength Mechanical Life Electrical Life Operating Temperature Double-break slow action contacts Two contacts in one deck Up to 6 decks available (Spring-return type: Up to 3 decks) Maintained Spring return 30, 45, 60, 90 45 2 to 12 2, 3, 4 100 M (500V DC megger) 2500V AC, 1 minute (between live and dead parts) 1 to 3 decks: 500,000 operations 4 to 6 decks: 200,000 operations 500,000 operations minimum -20 to +50C (no freezing) CBS Contact Block The CBS contact block contains two poles of double-break contacts. The contacts are operated by a cam designed to perform a required contact operation. Up to six contact blocks can be mounted on a maintained-action operator base, and up to three contact blocks on a spring return operator base. 46 M3.5 Screw Terminal 220V 6A 3A 1A 0.45A 440V 2A 1A 0.4A 0.2A CS Series Cam Switches o30/o25 Types Type o30 Series o25 Series ACSNO ACSSO Contact Arrangement Contact Block Decks Positions Angle Spring Return Handle Maintained: 1 to 6 decks Spring return: 1 to 3 decks Maintained: 2 to 12 positions Spring return: 2 to 4 positions Maintained: 30, 45, 60, 90 Spring return: 45 only Spring return from right Spring return from left Spring return two-way Y2, S2, P2, F2, 25S2 (25S2 is for ACSSO only) (one specified handle supplied) See page 56. (ordered separately) (Photo: ACSNO with Y2 handle) ACSNK ACSSK 58 H2 Handle Key (black) Maintained: 1 to 6 decks Spring return: 1 to 3 decks Maintained: 2 to 8 positions Spring return: 2 to 4 positions Maintained: 45, 90 Spring return: 45 only Spring return from right Spring return from left Spring return two-way Maintained: 1 to 6 decks Spring return: 1 to 3 decks Maintained: 2 to 12 positions Spring return: 2 to 4 positions Maintained: 30, 45, 60, 90 Spring return: 45 only Spring return from right Spring return from left Spring return two-way 24 Two standard keys are supplied. When the H2 key handle is required, specify H2. Nameplate See page 51. Standard Key (2 keys supplied) UCSQO (Enclosed Type) Y2, S2, F2, P2 (one specified handle supplied) (Photo: With Y2 handle) UCSQM (Enclosed Type) Indicator Left: Green Right: Red Left Type CQ See page 56. Spring return: 1 to 3 decks Right Spring return: 3 positions Spring return: 45 only C1007 C1008 C1009 C1010 C1018 C2006 C2007 C2021 See page 51. Spring return two-way Spring Return 2-way Type CQM See page 56. * For handles and accessories, see page 49. Dimensions 2 12N+9 12N+9 33 +0.5 0 35 o25.5 +0.5 0 (ACSSO/ACSSK) 47 Spring Return: 44 Maintained: 42 N: Number of Contact Blocks Spring Return: 44 Maintained: 42 N: Number of Contact Blocks o5 9 12 47 47 30.7 30 52 9 12 R0.8 max. +0.2 4.8 0 Panel Thickness 0.8 to 6 M3.5 Terminal Screw 52 50 (S2 Handle) 52 2 47 * Panel Cut-out ACSNK/ACSSK Panel Thickness 0.8 to 6 M3.5 Terminal Screw 52 ACSNO/ACSSO o30.5 +0.5 0 (ACSNO/ACSNK) * Minimum horizontal/vertical mounting centers With P2 handle: 125 With other handles: 70 UCSQO * Panel Cut-out UCSQM Panel Thickness 7.0 max. 46.4 Panel Thickness 7.0 max. 46.4 4-M4 Screw 4-o4.5 4-M4 Screw 12N+9 7 All dimensions in mm. 48 25 Spring Return: 31 Maintained: 29 N: Number of Contact Blocks M3.5 Terminal Screw 2 9 12 12N+9 48 64 52 9 12 50 (P2 Handle) 2 M3.5 Terminal Screw 64 52 41 (Y2 Handle) 3 o1 31 7 43 48 48 70 70 N: Number of Contact Blocks * Minimum horizontal/vertical mounting centers With P2 handle: 125 With other handles: 70 47 o30/o25 CS Series Cam Switches Ordering Information When ordering, specify items through as the designation example below. Contact Block Decks Type ACSNO ACSNK ACSSO ACSSK UCSQO UCSQM Decks 1 deck 2 decks 3 decks 4 decks 5 decks 6 decks Code 1 2 3 4 5 6 Spring return: 1 to 3 decks only Positions Angle Spring Return Positions Code Angle Code Return Code 2 positions 2 30 3 Spring return RO 3 positions 3 45 4 from left 4 positions 4 60 6 Spring return OR 5 positions 5 90 9 from right 6 positions 6 Spring return RR 7 positions 7 two-way 8 positions 8 9 positions 9 10 positions 10 11 positions 11 12 positions 12 Spring return: ACSNK/ACSSK: Spring return code is 2 to 4 positions only 45 and 90 only required only for spring return types. Spring return: 45 only * Designation Example Handle Circuit No. (Code) Y2, S2, P2, F2, H2, 25S2 (Color) B: Black See table below. For standard contact arrangements, use designation code on pages 51 to 53. For custom contact arrangements, use the Custom Contact Arrangement Specification Sheet on page 54. 25S2 is for ACSSO only. * Handle Designation Code UCSQO - 2 3 4 RR - S2B - C2006 Shape Code Applicable Cam Switch Color o30 Y Handle 1. When a special contact arrangement is required, specify the contact arrangement using the Custom Contact Arrangement Specification Sheet on page 54. 2. A specified handle is attached. 3. Accessories such as nameplates and jumpers are separately ordered. 4. The key of the key operated cam switch is removable from every position. Specify other key removable configurations if required. 22 30 19 Y2 ACSNO UCSQO UCSQM 20 o30 S Handle 20 30 30 S2 20 o25 S Handle 20 25.6 30 25S2 ACSSO 20 B: black o30 P Handle 30 50 P2 ACSNO UCSQO UCSQM 40 o30 F Handle o50 30 F2 40 Key Handle 18 40 ACSNK ACSSK H2 24 * Spring Return Operation Available combinations of operator positions, angles, and return directions are listed in the table below. Positions 2-position From Left From Right 2 Return Direction 1 2 2 1 3-position From Right From Left 1 2 2 3 1 4-position From Left From Right Two-way 3 1 2 3 1 24RO 24OR 34RO 34OR 34RR ACSNO, ACSSO, ACSNK, ACSSK, UCSQO 1 to 3 decks Note: Maintained types do not require spring return code . 48 44RO 2 3 3 2 4 Codes Applicable Cam Switches Contact Block Decks 3-position Two-way 4 1 3 1 44OR 34RR UCSQM CS Series Cam Switches o30/o25 Accessories and Replacement Parts Shape Material Type No. Ordering Type No. Package Quantity Remarks Jumper CJ-1 CJ-1 CJ-1PN10 10 For connecting terminals of adjoining contact blocks CJ-2 CJ-2PN10 10 For connecting terminals of the same contact block Metal CJ-2 Rubber Boot Rubber Terminal Cover Supplied with 2 selftapping screws for mounting CR-1 CR-1 1 For preventing ingress of dust into the contact blocks Not applicable for the UCSQO and UCSQM CS-VL2-13S CS-VL2-13S 1 For 1 to 3 decks of contact blocks CS-VL2-46S CS-VL2-46S 1 For 4 to 6 decks of contact blocks Plastic CS-VL2-13S CS-VL2-46S Shape Material (Color) Type No. Ordering Type No. Package Quantity o30 Y Handle 22 30 Plastic (Black) CSH-YB CSH-YB 1 Plastic (Black) CSH-SB CSH-SB 1 30 Plastic (Black) CSH-25SB CSH-25SB 1 50 Plastic (Black) CSH-PB CSH-PB 1 Plastic (Black) CSH-FB CSH-FB 1 Plastic (Black) CSH-H2B CSH-H2B 1 Plastic CS-HF2C CS-HF2CPN05 5 For Y, o30 S, and o25 S handles M3 x 12 CS-SCW-M3-12 CS-SCW-M3-12PN10 10 For P and F handles M3 x 25 CS-SCW-M3-25 CS-SCW-M3-25PN10 10 19 20 o30 S Handle 20 30 30 20 o25 S Handle 20 25.6 20 o30 P Handle 30 40 o30 F Handle o50 30 40 Key Handle 18 40 24 Handle Shaft Handle Screw Handle Screw 49 o30/o25 CS Series Cam Switches Minimum Mounting Centers for Installing the Terminal Cover Installing the Terminal Cover for the CS series Cam Switches 70 mm min. (P2 handle: 125 mm) * Complete wiring before installing the terminal cover on the bottom plate of the contact block. * The terminal cover has six holes. Of the four round holes at four corners, use two diagonal pair of holes to install the terminal cover. Either pair can be used. * Insert the attached self-tapping screws into the pair of holes and tighten the screws to a torque of 0.8 to 1.0 N*m. * For 1 through 3 decks of contact blocks, use terminal cover CS-VL2-13S. * For 4 through 6 decks of contact blocks, use terminal cover CS-VL2-46S. * The CS-VL2-46S consists of the CS-VL2-13S and a terminal cover for the fourth through sixth decks. Combine the two parts together as shown. Note that once combined, the two parts cannot be separated. 100 mm min. (P2 handle: 125 mm) * Although the minimum mounting centers are 100 mm horizontally and 70 mm vertically, determine the mounting centers in consideration of convenience of wiring. For the P2 handle, the minimum mounting centers are 125 mm horizontally and vertically. Mounting Hole Bottom Plate Self-tapping Screw (attached) Insert the screws into a diagonal pair of holes. CS-VL2-13S Mounting Hole CS-VL2-13S For 1 through 3 decks of contact blocks (CS-VL2-13S) For 4 through 6 decks of contact blocks (CS-VL2-46S) 52 64.6 (CS-VL2-13S) 66.1 (CS-VL2-46S) 33 (CS-VL2-13S) 34.5 (CS-VL2-46S) Terminal Cover Dimensions 9 47 91.4 (CS-VL2-13S) 94.4 (CS-VL2-46S) 2 7.5 12 12N+9 40.5 (N: Number of Contact Blocks) All dimensions in mm. 50 CS Series Cam Switches o30/o25 Standard Contact Arrangements * Listing Order of the Table The 76 standard contact arrangements are listed in the order of the circuit number. * Same Circuits Shown in the following examples, circuits of Fig. 1 and Fig. 2 have the same functions. When ordering, examine the standard contact arrangements. Your requirements may be satisfied simply by changing external wiring of the standard contact arrangments. * The following table lists 76 standard contact arrangements for easy designation of required cam switch operation. * When other contact arrangements are required, specify the number of contact block decks, operator positions, angles, and contact operation using the Custom Contact Arrangement Specification Sheet on page 54. No. of Decks: 2 Position: 3-position Angle: 45 Spring Return Type: 2-way Circuit No. 2 3 4 RR Fig. 1 7 5 3 1 C2006 7 5 3 1 8 6 4 2 8 6 4 2 1 2 Fig. 1 7 5 3 1 8 6 4 2 3 1 2 Example 2 Fig. 2 7 5 3 1 3 7 5 3 1 8 6 4 2 1 2 3 4 8 6 4 2 1 2 3 4 * Terminal Numbers The terminal numbers on the contact blocks correspond with the numbers shown in the chart as shown below. Terminal No. 1 2 3 Operator Position The arrow shows the spring return direction. Symbol Example 1 Fig. 2 Contact Operation Contacts closed. Contacts remain closed between two operator positions. Overlapping Contacts Contacts of different decks are both closed at one point while the handle is turned to the next position. Residual Contacts When the handle is returned to the center, the contacts remain closed. The contacts are opened when the handle is turned to the opposite direction. Terminal No. 7 5 3 1 8 6 4 2 2 Operator Position 134 C1005 1 Terminal No. Standard Contact Arrangement Chart 129 C1001 129 C1002 1 2 4 OR C1003 1 2 4 OR C1004 3 4 3 4 3 4 3 4 3 1 2 1 2 1 2 1 2 1 1 1 2 134 C1006 1 3 4 RR 1 2 12 2 C1007 1 3 4 RR C1008 1 3 4 RR C1009 4 3 4 3 4 3 4 3 2 1 2 1 2 1 2 1 144 123 123 3 C1011 129 C1013 129 123 C1014 1 2 4 OR C1015 4 3 4 3 4 3 4 3 2 1 2 1 2 1 2 1 3 124 1 4 C1017 2 1 3 4 RR 1 C1018 126 4 3 4 3 1 2 1 2 1 229 C2001 229 4 2 1 2 3 2 1 C2002 C1016 4 123 2 2 C1019 3 1 12 2 4 134 1 2 C1010 123 3 1 2 3 1 3 4 RR 1 2 2 1 3 1 4 2 234 C2003 234 C2004 234 C2005 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 1 2 1 2 3 1 2 3 2 1 2 3 51 o30/o25 CS Series Cam Switches 2 3 4 RR C2006 2 3 4 RR C2007 244 C2008 244 C2009 249 C2011 7 8 7 8 7 8 7 8 7 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 123 229 123 C2014 229 1 C2015 8 7 8 7 5 6 5 6 5 3 4 3 4 1 2 1 2 2 234 C2020 1 2 3 234 2 1 2 3 4 (O) (R) (S) (T) 4 C2017 234 C2018 8 7 8 7 8 6 5 6 5 6 3 4 3 4 3 4 1 2 1 2 1 1 234 4 C2016 12 C2019 3 234 7 1 2 2 1 3 2 3 4 RR C2021 2 244 2 3 1 C2022 2 3 233 C2023 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 3 233 1 C2024 2 123 3 243 C2025 253 1 C2027 2 3 236 2 1 4 C2028 2 3 236 C2029 8 7 8 7 8 7 7 8 7 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 1 3 329 C3001 2 3 334 8 4 1 C3002 2 3 4 354 1 5 C3003 2 364 2 1 2 3 (R) (S) (T) 3 C3004 334 C3005 11 12 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 349 1 C3008 11 12 9 10 7 8 5 6 3 4 1 2 3 349 C3009 2 3 4 329 1 5 C3010 2 3 4 334 5 2 6 1 C3011 2 3 344 C3012 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 1 C3013 1 11 1 2 3 4 (O) (RS) (ST) (TR) 363 2 8 2 3 336 4 1 C3014 2 366 1 C3015 2 353 2 3 1 C3016 2 3 344 4 C3017 11 12 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 2 1 1 2 3 4 336 5 1 6 C3018 2 336 3 1 C3019 2 444 4 5 6 1 C4001 484 2 3 4 2 1 5 C4002 2 3 449 4 C4003 15 16 15 16 15 11 12 11 12 13 14 13 14 13 14 9 10 9 10 11 12 11 12 11 12 7 8 7 8 9 10 9 10 9 10 5 6 5 6 7 8 7 8 7 8 3 4 3 4 5 6 5 6 5 6 1 2 1 2 3 4 3 4 3 4 1 2 1 2 1 1 2 3 1 2 3 1 424 C4004 429 C4005 2 429 3 4 C4006 1 2 3 4 5 6 7 8 449 C4007 2 1 2 3 4 (O) (R) (S) (T) 434 C4008 15 16 15 16 15 16 15 16 13 14 13 14 13 14 13 14 13 14 11 12 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 3 4 2 1 2 1 2 1 2 1 2 1 2 1 1 2 1 2 3 4 (O) (R) (S) (T) 16 16 15 1 52 3 2 1 2 3 CS Series Cam Switches o30/o25 454 C4009 534 C5001 644 C6001 6 12 3 C6002 23 24 23 24 19 20 21 22 21 22 15 16 17 18 19 20 19 20 13 14 15 16 17 18 17 18 11 12 13 14 15 16 15 16 9 10 11 12 13 14 13 14 7 8 9 10 11 12 11 12 5 6 7 8 9 10 9 10 3 4 5 6 7 8 7 8 1 2 3 4 5 6 5 6 1 2 3 4 3 4 1 2 1 1 2 3 4 5 1 2 3 1 649 C6003 693 2 3 2 1 4 C6004 2 3 666 4 5 6 7 8 C6005 9 10 11 12 664 C6006 23 24 23 24 23 24 23 24 21 22 21 22 21 22 21 22 19 20 19 20 19 20 19 20 17 18 17 18 17 18 17 18 15 16 15 16 15 16 15 16 13 14 13 14 13 14 13 14 11 12 11 12 11 12 11 12 9 10 9 10 9 10 9 10 7 8 7 8 7 8 7 8 5 6 5 6 5 6 5 6 3 4 3 4 3 4 3 4 1 2 1 2 1 2 1 (O) (R) (S) (T) 1 2 3 4 4 3 2 1 1 0 2 3 4 1 2 3 4 5 2 (RS)(ST)(RT)(RE)(SE)(TE) 1 2 3 4 5 6 6 Application Examples (Voltmeter and Ammeter Circuits) 1 2 6 C1019 (ammeter switching, 1CT circuit) 2 3 6 C2029 (ammeter switching, 2CT circuit) 2 4 9 C2011 (ammeter switching, 2CT circuit) CS CS CT 3 4 1 2 CS A R S T R S T A CT 7 8 5 6 3 4 1 2 A O R S T R S T CT 7 8 5 6 3 4 1 2 E E 2 4 4 C2022 (voltmeter switching, 3PT circuit) E 3 3 6 C3019 (ammeter switching, 3CT circuit) 3 4 9 C3008 (voltmeter switching, 2PT circuit) CS CS R S T E PT 3o-4W V CS A R S T R S T 11 12 9 10 11 12 9 10 7 8 5 6 7 8 7 8 3 4 5 6 5 6 1 2 3 4 3 4 1 2 1 2 CT V O RS ST TR R S T PT E 3 4 9 C3009 (voltmeter switching, 3PT circuit) 4 4 9 C4003 (ammeter switching, 3CT circuit) CS R S T E PT CS O R S T R S T V A O R S T R S T 11 12 15 16 15 16 9 10 13 14 13 14 7 8 11 12 11 12 5 6 9 10 9 10 3 4 7 8 7 8 2 5 6 5 6 3 4 3 4 1 2 1 2 1 3o-4W 4 4 9 C4007 (ammeter switching, 2CT circuit) CS CT 6 4 9 C6003 (ammeter switching, 3CT circuit) E CT A E CS O R S T R S T CT 23 24 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 A E 53 o30/o25 CS Series Cam Switches Custom Contact Arrangement Specification Sheet * The preceding pages provide 76 standard contact arrangements. When other contact arrangements are required, specify the number of contact block decks, operator positions, angles, and contact operation using the Custom Contact Arrangement Specification Sheet shown below. * For available number of contact blocks and operator positions, see the Ordering Information on page 48. 2. Specify contact operation at each operator position Indicate the required operation of all contacts at each operator position using the following symbols. Symbol Contact Operation Contacts closed. Contacts remain closed between two operator positions. Overlapping Contacts Contacts of different decks are both closed at one point while the handle is turned to the next position. Overlapping contacts are not available for handle angles of 30 and 45. Residual Contacts When the handle is returned to the center, the contacts remain closed. The contacts are opened when the handle is turned to the opposite direction. 1. Specify operator positions Indicate the operator positions starting at the first position. When spring return operation is required, mark an arrow between two operator positions to indicate the spring return direction. 7 Deck 2 5 * One deck of contact block contains two poles of contacts and four terminals. When the handle is made to turn 180 or more, special attention is needed. Since one cam operates the two poles of contacts on opposite positions, the same contact operation repeats on the other pole of contacts when the handle is turned 180. When different contact operation is needed for handle angles of 180 or more, use another deck of contact block. 3 Deck 1 1 Angle Positions Spring Return 1 2 3 4 5 CS Series Cam Switch Custom Contact Arrangement Specification Sheet Type No.: Quantity: Type Deck Decks Positions Terminal No. Angle Spring Return Handle Contact Arrangement Chart Terminal No. 23 24 21 22 19 20 17 18 15 16 13 14 11 12 9 10 7 8 5 6 3 4 1 2 Deck 6 Deck 5 Deck 4 Deck 3 Deck 2 Deck 1 Angle Positions Spring Return 54 1 2 3 4 5 6 7 8 9 10 11 12 o30 Series Accessories and Replacement Parts o30 Accessories Terminal Cover N-VL2 N-VL3 N-VL4 APN-PVL APD-PVL 38.4H x 22W 38H x 30.4W 38.4H x 24W 38H x 46W 37H x 44W Use of terminal covers increases the depth by the dimensions below. Terminal Cover o30 Series Control Unit Pilot Light APN, APNE, UPQN, UPQNE X +5.0 mm Full Voltage Pilot Light APD, APDE Pilot Light APN, APNE, APD, APDE, UPQN, UPQNE X Transformer DC-DC Converter X +5.2 mm +2.7 mm 1 contact block Terminal Cover Pushbutton ABN, ABD, AON, AOD, AVN, ABGD, AJN, ABFD, ATN, AOFD, UBQN, AVD, UOQN, AJD, UWQN, AZD, ABBN, AYD, ABBS (o25) X CB 2 contact blocks CB CB X 2 pieces +0 mm 3 contact blocks Selector Switch ASN, ASD, ASTN Selector Pushbutton ABN, ASBD CB CB CB X 2 pieces 4 contact blocks CB CB CB CB X 2 pieces Illuminated Pushbutton ALN, ALD, ALNE, ALDE, AOLN, AOLD, AOLNE, AOLDE, ALGN, ALGD, Full Voltage ALGNE, ALGDE, AOLGN, AOLGDE, ALFN, ALFD, ALFNE, ALFDE, AOLFN, AOLFD, AOLFNE, AOLFDE, AVLN, AVLD, AVLNE, AVLDE, AJLN, AJLD, AJLNE, AJLDE, ULQN, UOLQN Illuminated Selector Switch ASLN, ASLD Transformer DC-DC Converter X 2 pieces X +4.5 mm +1.5 mm Push-to-Check Pilot Light APN1P * Ordering Terminal Covers When ordering terminal covers, specify the Type No. and the quantity. 55 o30 o30 Series Accessories and Replacement Parts Nameplates Legend Material Blank Type No. Package Quantity NA-0 1 NA-0PN10 10 Dimensions (mm) Applicable Unit NA-0 Aluminium 1.2 mm thick White letters on black background NA Ordering Type No. 40 24.5 Type NA- 1 R1 7. 5 0.5 o3 With Legend NA- NA-PN10 10 NALO 1 NALOPN10 10 o30 Control Unit Blank NALO .5 0 o3 Aluminium 1.2 mm thick Black R1 7. 5 NALO 47.5 30 40 70 4 Blank Blank MLO MLO MLOPN10 With Legend (Legend Codes 31 and 53 only) CQ-0PN10 10 CQ- ARN/ARNS Mono-Lever o43 Letters should not be engraved within this line * With adhesive tapes on the back 2-o3.5 1 o13 CQ-PN10 20 64 10 CQM-0 1 CQM-0PN10 10 * With adhesive tapes on the back CQM-0 5 12 UCSQM Cam Switch CQM- 1 2-o3.5 o13 40 64 CQM- * Specify a legend code in place of in the Ordering Type No. 56 1 .5 UCSQO Cam Switch Aluminium 0.5 mm thick White letters on black background With Legend (Legend Code 31 only) CQ-0 CQ- Blank CQM 10 0 o3 CQ-0 Aluminium 0.5 mm thick White letters on black background CQ 1 29.3 MLO Brass (chrome-plated) 1.0 mm thick Matte CQM-PN10 10 o30 Series Accessories and Replacement Parts o30 Nameplates Type Legend Material Blank Ordering Type No. Type No. Package Quantity Dimensions (mm) Applicable Unit * With adhesive tapes on the back CQN-0 1 CQN-0PN10 10 CQN-0 Aluminium 0.5 mm thick White letters on black background CQN With Legend (Legend Codes 31, 35, and 53 only) CQN- 1 CQN- Blank ACSNO, ACSNK Cam Switches o30 mm Selector Switches .5 o30 64 CQN-PN10 10 CQS-0 1 CQS-0PN10 10 CQS- 1 CQS-PN10 10 HNAV-0 1 * With adhesive tapes on the back CQS-0 CQS With Legend (Legend Code 53 only) .5 5 o2 Aluminium 0.5 mm thick White letters on black background ACSSO, ACSSK Cam Switches o25 mm Selector Switches CQS- 64 Blank HNAV-0 o60 Polyamide Black letters on yellow background HNAV EMERGENCY o3 0 1.5 HNAV-27 HNAV-27 1 1.0 HN1E o30 mm series Emergency Stop Switches Legend "EMERGENCY STOP" is indicated outside a o44mm circle. * Specify a legend code in place of in the Ordering Type No. Legends Code 0 1 2 3 4 31 35 53 Legend (blank) ON OFF START STOP OFF-ON HAND-AUTO HAND-OFF-AUTO Shape and Engraving Area 36 2 18.5 18.5 5 36 2 10 2 2 Standard Large Type NA Type NALO Example Shape Standard Large Engraving Area Height Width 5 36 10 36 Max. No. of Lines No. of Letters on 1 Line 1 2 14 14 * The above example is when the letter is 4 mm tall. 57 o30 o30 Series Accessories and Replacement Parts Accessories Shape Material Type No. Ordering Type No. Package Quantity Dimensions (mm) o2 2 OR-12 OR-12 1 6 o2 29 o 4 o3 o46 o45 o37 Rubber o3 0 * Used to tighten the locking ring when installing the o30 or o25 switch onto a panel. Locking Ring Wrench 90 o25 Series o30 Series Rubber OR-55 OR-55 o11.6 * Used to install and remove the LED/incandescent lamps. See page 64. Lamp Holder Tool 1 14 OR-55 59 * Rubber boot used to prevent oil and dirt from entering into the contact block. * Temperature range: -5 to +60C * Cannot be used for zinc diecast control units. Contact Rubber Boot For momentary 1 layer of contact blocks (2 contact blocks) 18 OC-99 42 1 52 Rubber (nitryl) OC-99 (black) 44 For 1 layer of contact blocks (2 contact blocks) For 2 layers of contact blocks (4 contact blocks) OC-90 OC-90 1 OC-290 OC-290 1 Rubber (translucent) * Applicable to AVN3 and AJN3. * Applicable to o30 diecast zinc pushbuttons and selector switches. 38.8 Contact Rubber Boot 42.8 42.4 (65.4) * Used to prevent the operator from turning. Generally used when using no nameplates on selector switches and selector pushbuttons. See page 64. Anti-rotation Ring Metal OGL-11 OGL-11PN10 2.8 10 0.8 .5 o30 o3 OB-13BPN05 5 o40 10 OB-13B o30 5 Rubber (black) * Used to plug unused o30mm mounting holes. * Gray also available. Ordering Type No.: OB-13PN05 5 9 Rubber Mounting Hole Plug o34 * Tightening torque: 1.2 N*m. * Degree of protection: IP65 Plastic Mounting Hole Plug OBP-11 1 24 OBP-11 5 o36 Plastic (gray) 4 M30 P1.5 Screw Locking Ring * Tightening torque: 1.2 N*m. * Degree of protection: IP65 Metallic Mounting Hole Plug OB-11 1 30 OB-11 5 o36 Metal (diecast) (zinc-plated) 4 M30 P1.5 Screw Locking Ring 58 o30 Series Accessories and Replacement Parts o30 Accessories Rubber (nitryl) Type Package Quantity - - Black OC-11B OC-11B Green OC-11R OC-11R Red OC-11G OC-11G Yellow OC-11Y OC-11Y 1 OC-121 OC-121 1 OC-122 OC-122 1 Rubber (EPDM) For extended pushbuttons * Metallic bezels covered with a rubber boot to enhance waterproof characteristics. * Button is not included. Applicable to extended pushbuttons only. o28 o38 M30 P1.5 Pushbutton Clear Boot For flush pushbuttons Dimensions (mm) * Used to cover and protect pushbuttons where units are subject to water splash. Not suitable for outdoor use or where the units are subject to oil splash. A 37 37 OC-121 OC-122 A B 16 16 * Used for ABN4G pushbuttons. Dust-proof Rubber Cover for Jumbo Mushrooms Rubber (nitryl) black OC-4GN OC-4GN 19 Color Ordering Type No. B Button Cover for Extended Pushbuttons Type No. 11 Material Panel Thickness 1.2 to 5.5 o80 Shape 1 32 * Used to protect pushbuttons, illuminated pushbuttons, and selector switches (knob operator). Padlock Cover 82.5 Panel Thickness 0.8 to 3.2 R6 OL-KL1 1 70 30 OL-KL1 93 6.5 Polyarylate (gasket: nitryl rubber) 24 o3 0 o5 0. 2 Key Hole o8 29.5 Waterproof Rubber Gasket 0.5t 30 * Used to protect flush pushbuttons from inadvertent operation. * Can be easily attached using the locking ring. Metal Protector 42.5 OL-C OL-C 1 16 Mounting Centers 50 min. Metal (zinc-plated) .5 o30 1.6 11.5 * Used to lock an extended pushbutton in the depressed position. * Can be easily attached using the locking ring. 30 Locking Attachment OL-H 1 Locking Plate o5 hole 9.5 OL-H 16.5 Metal (zinc-plated) Mounting Plate 59 o30 o30 Series Accessories and Replacement Parts Maintenance Parts Shape Specification Type No. Ordering Type No. Package Quantity Remarks Metallic Bezel Metal (chrome-plated) OG-11 OG-11PN02 2 Plastic OGP-11 OGP-11PN02 2 OGP-13 OGP-13PN02 2 OGP-14 OGP-14PN02 2 OGP-1411 OGP-1411 1 Clear Plastic ABN1B-C ABN1B-CPN05 5 Plastic TN-0 TN-0PN10 10 Plastic Bezel Specify a color code in place of . B (black), G (green), R (red), W (white), Y (yellow) Clear Plastic Bezel for Flush Pushbuttons Clear Plastic Bezel for Extended Pushbuttons Clear Plastic * Clear plastic bezel and full shroud. * OGP-1411 cannot be used with LED illumination units and diecast units. Clear Plastic Bezel for Illuminated Pushbuttons Clear Button Cover Marking Plate 60 * Used on flush and extended pushbuttons to indicate a mark or a symbol engraved on the marking plate. The clear button cover holds the marking plate. The o30 series marking chip can only be used on the ABN1 and AON1. * Specify a color code in place of . B (black), G (green), R (red), W (white), Y (yellow) o30 Series Accessories and Replacement Parts o30 Maintenance Parts Shape Description Contact Block (BS: Dark gray) Contact Block (BST: Light gray) Lens Button Package Quantity Color BS010E 1 * Push rod color: Green 1NC contact BS001E BS001E 1 * Push rod color: Red EM contact (early make) LB contact (late break) BS010SE BS010SE 1 * Push rod color: Black BS001SE BS001SE 1 * Push rod color: White 1NO contact BST010 BST010 1 * Push rod color: Green 1NC contact BST001 BST001 1 EM contact (early make) BST010S BST010S 1 LB contact (late break) BST001S BST001S 1 Used for APN(E)1 APN106LN- APN106LN-PN05 5 UPQN406L- UPQN406L-PN05 Plastic 5 UPQN406LD- UPQN406LD-PN05 Used for UPQN3B U(O)LQN ULQN06L- ULQN06L-PN05 UPQN06LD- UPQN06LD-PN05 Used for ALN, AOLN (LED) ALN2L- Used for ALN, AOLN (incandescent) (1W) Applicable Units: * Pushlock Turn Reset * Push Turn Lock * Push rod * LED Illuminated color: Red Pushbutton * LED Illuminated Selector Switch * Push rod color: Black * Incandescent Illuminated Selector Switch * Push rod color: White * All o30 Diecast Zinc Control Units A (amber), C (clear), G (green), R (red), S (blue), W (white), Y (yellow) * Use the white (W) lens for pure white illumination C (clear), G (green), R (red), S (blue) * Use the clear (C) lens for white illumination. A (amber), Y (yellow) * Use the amber (A) lens for orange illumination. C (clear), G (green), R (red), S (blue) 5 A (amber), W (white), Y (yellow) * Use the amber (A) lens for orange illumination. ALN2L-PN05 5 G (green), R (red), S (blue) ALN2LD- ALN2LD-PN05 5 A (amber), W (white), Y (yellow) * Use the white (W) lens for pure white illumination ALN06L- ALN06L-PN05 5 C (clear), G (green), R (red), S (blue) ALN06LD- ALN06LD-PN05 5 A (amber), W (white) * Use the amber (A) lens for orange illumination. Used for ALN, AOLN (incandescent) (2W) ALN08L- ALN08L-PN05 5 C (clear), G (green), R (red), S (blue) ALN08LD- ALN08LD-PN05 5 A (amber), W (white) * Use the amber (A) lens for orange illumination. Flush ABN1B- ABN1B-PN05 5 Extended ABN2B- ABN2B-PN05 5 ABN3B- ABN3B-PN02 2 Flush ABN1BN- ABN1BN-PN05 5 Extended ABN2BN- ABN2BN-PN05 5 Mushroom ABN3BN- ABN3BN-PN02 2 ABN4B- 1 ABN4GB- 1 UBQN1B-PN02 2 UBQN2B-PN02 2 Plastic G (green), R (red), Y (yellow) Above colors are used for o30 control units (dark colored operator units). For black, use black buttons from light colored operator units. Plastic Button Button Ordering Type No. BS010E Mushroom Type No. 1NO contact Used for UPQNE4 U(O)LQNB Lens Material Mushroom ABN4B- (ABN4) Mushroom (ABN4G/ ABN4GB- ABN4F) Plastic Square Flush UBQN1B- (UBQN1) Square Extended UBQN2B- (UBQN2) B (black), G (green), R (red), S (blue), Y (yellow), W (white) Above colors are used for o30 diecast zinc control units (light colored operator units). B (black), G (green), R (red), Y (yellow) Note: Specify a button color code or lens color code in place of or in the Ordering Type No. 61 o30 o30 Series Accessories and Replacement Parts Maintenance Parts Shape Description Material Type No. Ordering Type No. Package Quantity Remarks Lens For o40 pushlock turn reset pushbuttons AVLN3L-R AVLN3L-RPN02 2 For UPQN4 Plastic UPQN406N-W UPQN406N-WPN05 5 ASNK Metal ASN-SK-24401 ASN-SK-24401PN02 2 Rubber OW-12 OW-12PN10 10 Rubber OW-11 OW-11PN10 10 Half shroud (for pushbuttons) ABN2G ABN2G 1 Full shroud (for pushbuttons) ABN2F ABN2F 1 ABN3G ABN3G 1 ABN4G ABN4G 1 ABN4F ABN4F 1 Half shroud (for illuminated pushbuttons) ALN1GL ALN1GL 1 ALN2GL ALN2GL 1 Full shroud (for illuminated pushbuttons) ALN1F ALN1F 1 ALN2FL ALN2FL 1 TWR-016N TWR-016N 1 Marking Plate Spare Key * Applicable to ABN3K, ABN4K, ABN5 Rubber Washer (3.0mm thick) Rubber Washer (1.5mm thick) Shroud Full shroud (for mushroom pushbuttons) Shallow shroud (for jumbo mushrooms) Metal Deep shroud (for jumbo mushrooms) Transformer 100/110V AC (for LED/1W incandescent lamps) * For incandescent/LED illuminated pushbuttons (E12 base) * For LED illuminated pushbuttons (BA9S base) * For incandescent/LED illuminated pushbuttons (E12 base) * For LED illuminated pushbuttons (BA9S base) Mounting screws are not included. 200/220V AC (for LED/1W incandescent lamps) 62 TWR-026N TWR-026N 1 o30 Series Accessories and Replacement Parts o30 Maintenance Parts LED Lamps Current Draw AC DC Operating Voltage Dimensions 6V AC/DC 10% 17 mA (A, R, W, Y) 8 mA (G, PW, S) 14 mA (A, R, W, Y) 5.5 mA (G, PW, S) Ordering Type No. Type No. Illumination Color Code Specify a color code in place of in the Ordering Type No. LSTD-6 LSTD-6 LSTD-6PN10 Base BA9S/13 A: G: PW: R: S: W: Y: o10 LSTD-1 12V AC/DC 10% 11 mA 10 mA LSTD-1 LSTD-1PN10 20.4 LSTD-2 24V AC/DC 10% 11 mA 10 mA LSTD-2 amber green pure white red blue white yellow LSTD-2PN10 6V AC/DC 10% 17 mA (A, R, W, Y) 8 mA (G, PW, S) 14 mA (A, R, W, Y) 5.5 mA (G, PW, S) Specify a color code in place of in the Ordering Type No. LETD-6 LETD-6 LETD-6PN10 A: G: R: S: W: Y: o12 LETD-8 6.5 mA LETD-8 LETD-8PN10 27 LETD-2 24V AC/DC 10% 11 mA 10 mA Base 1 10 1 BA9S/13 10 1 10 Base E12/15 12V AC/DC 10% 7 mA Package Quantity amber green red blue white yellow 1 10 1 E12/15 10 1 LETD-2 LETD-2PN10 10 Incandescent Lamps Dimensions 22.51.5 o111 Base BA9S/13 o131 Base E12/15 342 Rated Operating Voltage Lamp Ratings Type No. 6V AC/DC 1W (6.3V) LS-6 12V AC/DC 1W (18V) LS-8 18V AC/DC 1W (24V) LS-2 24V AC/DC 1W (30V) LS-3 6V AC/DC 2W (6.3V) LE-6 12V AC/DC 2W (18V) LE-8 18V AC/DC 2W (24V) LE-2 24V AC/DC 2W (30V) LE-3 Package Quantity Life 1 Approx. 1000 hours minimum (reference value) 1 Transformer Separate Mounting Type For 1W Primary Voltage 100/110V AC 200/220V AC For 2W Secondary Voltage Type No. TWR516 5.5V TWR526 400/440V AC TWR546 100/110V AC TWR518 200/220V AC 400/440V AC Applicable Load 15V TWR528 One full voltage type pilot light or illuminated switch containing LSTD-6, LETD-6 LED lamp (6V AC/DC) or LS-6 incandescent lamp (6.3 V AC/DC, 1W) One full voltage type pilot light or illuminated switch containing LE-8 incandescent lamp (18V AC/DC, 2W) TWR548 63 o30 o30 Series Instructions Safety Precautions * Turn off the power to the o30 series control units before starting installation, removal, wiring, maintenance, and inspection of the products. Failure to turn power off may cause electrical shocks or fire hazard. * To avoid a burn on your hand, use the lamp holder tool when replacing lamps. * For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a tightening torque of 1.0 to 1.3 N*m. Failure to tighten terminal screws may cause overheat and fire. Instructions Panel Mounting for Square Pushbuttons and Pilot Lights 1. Tighten the square ring to the operator and position the ring correctly. 2. Lightly tighten the screw to secure the pilot light onto the panel. Recommended tightening torque: 0.15 N*m Tightening Torque for Terminal Screws Tighten the terminal screws to a torque of 1.0 to 1.3 N*m. Lamps can be replaced by using the lamp holder tool (OR55) from the front of the panel. * How to Remove To remove, slip the lamp holder tool onto the lamp head lightly. Then push slightly, and turn the lamp holder tool counterclockwise. * How to Install To install, insert the lamp head into the lamp holder tool. Place the pins on the lamp base to the grooves in the lamp socket. Inset the lamp and turn it clockwise. Applicable Models Applicable Models * Extended Illuminated Pushbuttons with Half Shroud (LED) * Extended Pushbuttons with Half Shroud (Diecast) * Extended Illuminated Pushbuttons with Half Shroud (Diecast) * Extended Pushbuttons with Half Shroud * Extended Illuminated Pushbuttons with Half Shroud (Incandescent) Panel Rubber Washer Thickness 1.5mm 3.0mm (mm) Supplied 1 piece 1 piece 0.8 1 piece 1 piece 0.8 to 2.3 - 1 piece 2.3 to 4.0 1 piece - Panel Thickness Rubber Washer (mm) 1.5mm 3.0mm Supplied 1 piece 1 piece 0.8 to 1.8 - 1 piece 1.8 to 3.5 1 piece - * Extended Illuminated Pushbuttons with Full Shroud (Incandescent) * Extended Illuminated Pushbuttons with Full Shroud (LED) * Extended Illuminated Pushbuttons with Full Shroud (Diecast) * Mushroom Pushbuttons with Full Shroud Panel Thickness Rubber Washer (mm) 1.5mm 3.0mm Supplied 2 pieces 1 piece 0.8 to 2.0 1 piece 1 piece 2.0 to 3.5 1 piece 1 piece 3.5 to 5.0 - 1 piece 5.0 to 6.0 (6.5) 1 piece - The number in brackets is for mushroom pushbuttons with full shroud. Extended illuminated pushbuttons with full shroud (incandescent) are 5.0 mm maximum. Applicable Models OR-55 * Toggle Lever Types * Knob Push Turn Lock Illuminated Pushbuttons Installing the Anti-rotation Ring Panel Rubber Washer 1.5mm 3.0mm Supplied 1 piece 1 piece 0.8 to 2.0 1 piece 1 piece 2.0 to 3.5 - 1 piece 3.5 to 5.5 (5.0) 1 piece - The number in brackets is for knob push turn lock illuminated pushbuttons. Panel Thickness (mm) OGL11 Rubber Washer 64 Adjust the thickness of the rubber washers according to the panel thickness. Also, make sure to include the nameplate thickness when using a nameplate. Applicable Models Replacement of Lamps Anti-rotation rings are used on selector switches or pushbuttons which rotate and used when using no nameplates. Insert a 1.5mm thick rubber washer between the panel and the anti-rotation ring as shown on the right. Panel Thickness and Rubber Washer Applicable Models * Extended Pushbuttons with Full Shroud Panel Thickness (mm) Supplied 0.8 to 1.5 1.5 to 3.0 3.0 to 4.5 4.5 to 6.0 6.0 to 7.5 Rubber Washer 1.5mm 3.0mm 3 pieces 3 pieces 2 pieces 1 piece - 1 piece 1 piece 1 piece 1 piece 1 piece 1 piece - Applicable Models * Extended Pushbuttons with Full Shroud (Diecast) Panel Thickness (mm) Supplied 0.8 to 2.5 2.5 to 4.0 4.0 to 5.5 5.5 to 6.0 Rubber Washer 1.5mm 3.0mm 2 pieces 2 pieces 1 pieces - 1 piece 1 piece 1 piece 1 piece 1 piece - Applicable Models * Other Models (Excluding Square Types) Panel Thickness (mm) Supplied 0.8 to 3.5 3.5 to 5.0 5.0 to 6.5 6.5 to 7.5 Rubber Washer 1.5mm 3.0mm 2 pieces 2 pieces 1 piece - 1 piece 1 piece 1 piece 1 piece 1 piece - o30 Series Instructions o30 Installation of LED Illuminated Units 1. Note the polarity for wiring when connecting to DC-DC converter unit. Terminal No. X1 X2 Polarity Positive Negative 2. Transformer type units are recommended for use in areas subjected to noise. 3. Notes for Pure White LED Lamps * Do not use the pure white LED outdoors, otherwise it will lead to the degradation of brightness and color. Do not remove or apply shock to the cap on the pure white LED lamp, otherwise it may break or damage the cap. * For the pure white LED, use a white lens. The illumination color will be dull if a different color is used. Notes on LED Illuminated Units LED lamps consist of semiconductors. If the applied voltage exceeds the rated voltage, LED elements may deteriorate due to overheat, resulting in significant decrease in luminance, hue change, or failure of lighting. Also, if an extraneous noise, transient voltage, or transient current is applied to the circuit, similar effects may occur. When using LED lamps, observe the following instructions. * Rated Voltage The LED lamps are rated at 6V, 12V, or 24V AC/DC, and can be used within 10% the rated voltage of either AC or DC. * DC Power 1. Switching power supply Regulated voltage from switching power supply is best suited. Make sure to use within the rated voltage of the LED lamp. 2. Rechargeable battery Note that the battery voltage may exceed the rated voltage of the LED lamp while the battery is being charged and immediately after the charging is complete. Be sure to use the LED lamp on a voltage of 10% the rated voltage. 3. Full-wave rectification Since the LED lamp is AC/DC compatible, a diode bridge for rectification is not necessary. If the LED lamp is used on a full-wave rectification current through a diode bridge, the rectifier diodes will reduce the voltage, resulting in lower luminance. 4. Single-phase half-wave rectification This is not suitable for the power source of LED lamps. Use constant-voltage DC power. * Noise LED elements deteriorate due to extraneous noise, resulting in significant decrease in luminance, hue change, or failure of lighting. When such effects are anticipated, take a protection measure shown below, such as RC elements or a surge absorber. [Protection Example 1] For AC circuit LED with transformer C C LED with transformer LED Relay Ry coil or solenoid R LED R (Reference values) R: 120 C: 0.1 F [Protection Example 2] For DC circuit + (Reference values of the diode) Forward current: More than the Ry coil current Reverse withstand voltage: Ry coil current x 10 Relay Ry coil or solenoid LED Diode - * Countermeasures against Dim Lighting 1. Leakage currents through the transistors or a contact protection circuit may cause the LED lamp to illuminate dimly even when the output is off. 2. When the LED lamp is illuminated by a transistor output, take the following measure. [Circuit Example] Connect shunt resistor R in parallel with the LED lamp. R LED Io Io: Leakage current when the output is off R: Shunt resistor 65 o30 o30 Series Diecast Zinc Control Units Heavy duty switches for tough industrial usage * Degree of protection: IP65 (IEC 60529) * UL, CSA approved, and EN compliant Safety Standards File No. or Organization UL UL Listing File No. E68961 CSA File No. LR21451 EN EN60947-5-1 Specifications and Ratings Contact Ratings Pushbuttons Illuminated Pushbuttons Selector Switches Illuminated Selector Switches Selector Pushbuttons Contact Block Rated Insulation Voltage Rated Continuous Current Contact Ratings by Utilization Category IEC 60947-5-1 Type BST (o30 series) 600V 10A AC-15 (A600) DC-13 (P600) Characteristics * Contact Ratings by Utilization Category Operational Voltage AC-12 Control of resistive loads and solid state loads AC Operational 50/60 Hz AC-15 Control of electromagnetic loads (> 72 VA) Current DC-12 Control of resistive loads and solid state loads DC DC-13 Control of electromagnets 24V 10A 10A 10A 5A 48V -- -- 5A 2A 50V 10A 7A -- -- 110V 10A 5A 2.2A 1.1A 220V 6A 3A 1.1A 0.6A 440V 2A 1A -- -- Note: The operational current represents the classification by making and breaking currents (IEC 60947-5-1). Minimum applicable load: 3V AC/DC, 5 mA (applicable range may vary with operating conditions and load types) BST Contact Block (Light Gray) * Contact Block Types Single-pole Contact Block Type * Interlocking Groove Contact * M3.5 Terminal Screw 1NO 1NC 1NO (early make) 1NC (late break) Type BST BST010 BST001 BST010S BST001S Push Rod Green Red Black White Note: BST contact blocks are not interchangeable with dark gray BS contact blocks used for o30 control units. * Mounting Screw * Inspection Window * Push Rod Specifications, ratings, and mounting hole layouts are the same as o30 control units. See "o30 Series Control Units" on page 7. 66 o30 Series Diecast Zinc Control Units o30 Ordering Information Standard Units Terminal Cover * Specify an operator or lens color code in the Type No. * Black, green, and red colored buttons are included with flush pushbuttons. * Full voltage type illuminated units are not supplied with a lamp. Order LED or incandescent lamps separately. Transformer type illuminated units contain an LED or incandescent lamp. * Terminal covers, nameplates, and accessories are ordered separately. * When a terminal cover is required, order an applicable terminal cover referring to page 55. The Type No. development charts shown below can be used to specify control units other than those listed on the following pages. o30 Series Diecast Zinc Pushbuttons ABD2 11 N R Button color code Contact arrangement code 10: 1NO 01: 1NC 11: 1NO-1NC 20: 2NO 02: 2NC 22: 2NO-2NC Note: * Mushroom pull type AZD3 can have a maximum of two contact blocks. * Mushroom push-pull type AYD31 can have a maximum of two contact blocks. o30 Series Diecast Zinc Pilot Lights APDE 1 99 D N R Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Operating voltage code 99: Full voltage 16/18: Transformer (100/110V AC) 116/118: Transformer (115V AC) 126/128: Transformer (120V AC) 26/28: Transformer (200/220V AC) 236/238: Transformer (230V AC) 246/248: Transformer (240V AC) 386/388: Transformer (380V AC) 46/48: Transformer (400/440V AC) 486/488: Transformer (480V AC) Lamp receptacle: E: E12 (LETD-6 LED or 2W incandescent lamps) (blank): BA9S (LSTD-6 LED or 1W incandescent lamps) o30 Series Diecast Zinc Illuminated Pushbuttons ALDE 2 16 11 D N R Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Contact arrangement code 11: 1NO-1NC 20: 2NO 02: 2NC 31: 3NO-1NC 22: 2NO-2NC 13: 1NO-3NC 40: 4NO 04: 4NC Operating voltage code 99: Full voltage 16/18: Transformer (100/110V AC) 116/118: Transformer (115V AC) 126/128: Transformer (120V AC) 26/28: Transformer (200/220V AC) 236/238: Transformer (230V AC) 246/248: Transformer (240V AC) 386/388: Transformer (380V AC) 46/48: Transformer (400/440V AC) 486/488: Transformer (480V AC) Lamp receptacle E: E12 (LETD-6 LED or 2W incandescent lamps) (blank): BA9S (LSTD-6 LED or 1W incandescent lamps) Note: * Illuminated pushbuttons cannot have an odd number of contact blocks, such as 1NO, 1NC, 3NO, 2NO-1NC, 1NO-2NC, and 3NC. * Full voltage type is not supplied with a lamp. * Transformer types contain an LED lamp (LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8, 2W). * LED lamps cannot be used on 480V AC transformers. * Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48, and 488 are available for incandescent types only. Note: * Full voltage type is not supplied with a lamp. * Transformer types contain an LED lamp (LSTD-6 or LETD-6) or incandescent lamp (LS-6, 1W or LE-8, 2W). * LED lamps cannot be used on 480V AC transformers. * Operating voltage codes 18, 118, 128, 28, 238, 248, 388, 48, and 488 are available for incandescent types only. 67 o30 o30 Series Diecast Zinc Control Units o30 Series Diecast Zinc Selector Switch ASD 2 L 11 N Contact arrangement code Operator type (blank): Knob L: Lever Number of positions o30 Series Diecast Zinc Key Selector Switch ASD 2 K 20 N B Key removable position code 2-position * Maintained (blank): Removable in all positions B: Removable in left only C: Removable in right only * Spring return from right (blank): Removable in left only * Spring return from left (blank): Removable in right only 3-position * Maintained (blank): Removable in all positions B: Removable in left and center C: Removable in right and center D: Removable in center only E: Removable in right and left G: Removable in left only H: Removable in right only * Spring return from right (blank): Removable in left and center D: Removable in center only G: Removable in left only * Spring return from left (blank): Removable in right and center D: Removable in center only H: Removable in right only * Spring return two-way (blank): Removable in center only Contact arrangement code Number of positions Note: * The key cannot be removed in the return position. 68 o30 Series Diecast Zinc Illuminated Selector Switch ASLD 2 16 22 D N R Lens color code Lamp type D: LED (Transformer type only) (blank): Incandescent Contact arrangement code Operating voltage code 99: Full voltage 16: Transformer (100/110V AC) 156: Transformer (115V AC) 136: Transformer (120V AC) 26: Transformer (200/220V AC) 236: Transformer (230V AC) 256: Transformer (240V AC) 386: Transformer (380V AC) 46: Transformer (400/440V AC) 486: Transformer (480V AC) Number of positions Note: * Full voltage type is not supplied with a lamp. * Transformer type contains an LED lamp (LSTD-6) or incandescent lamp (LS-6). * LED lamps cannot be used on 480V AC transformers. o30 Diecast Zinc Series Pushbuttons o30 Flush / Extended / Extended with Half Shroud / Extended with Full Shroud Flush ABD1 Momentary Contact Type No. 1NO ABD110N 1NC ABD101N 1NO-1NC ABD111N 2NO ABD120N 2NC ABD102N 2NO-2NC ABD122N Flush AOD1 Maintained 1NO AOD110N 1NC AOD101N 1NO-1NC AOD111N 2NO AOD120N 2NC AOD102N Button Color Code Black (B), green (G), and red (R) buttons are supplied with each unit. Specify S, Y, or W when a blue, yellow, or white button is required. Dimensions (mm) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 6 36 Operation Type o35 Shape 23 40 68 (1 to 2 blocks) 91 (3 to 4 blocks) 9 2NO-2NC AOD122N ABD210N 1NC ABD201N 1NO-1NC ABD211N 2NO ABD220N 2NC ABD202N Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw Maintained 1NO AOD210N 1NC AOD201N o25 2NO-2NC ABD222N Extended AOD2 5.5 2NO AOD220N 2NC AOD202N 23 53 (1 or 2 blocks) 1NO-1NC AOD211N o40 Momentary 1NO o35 Extended ABD2 40 9 14.5 76 (3 or 4 blocks) 2NO-2NC AOD222N ABGD210N 1NC ABGD201N 1NO-1NC ABGD211N 2NO ABGD220N 2NC ABGD202N 2NO-2NC ABGD222N Extended with Half Shroud AOGD2 Maintained 1NO AOGD210N 1NC AOGD201N 1NO-1NC AOGD211N 2NO AOGD220N 2NC AOGD202N Specify a button color code in place of in the Type No. B: G: R: S: W: Y: black green red blue white yellow M3.5 Terminal Screw Panel Thickness 0.8 to 3.5 5.5 23 49.5 (1 or 2 blocks) o40 Momentary 1NO o25 o27 o35 Extended with Half Shroud ABGD2 40 20.5 72.5 (3 or 4 blocks) 2NO-2NC AOGD222N ABFD210N 1NC ABFD201N 1NO-1NC ABFD211N ABFD202N M3.5 Terminal Screw Panel Thickness 0.8 to 6 2NO-2NC ABFD222N Extended with Full Shroud AOFD2 Maintained 1NO AOFD210N 1NC AOFD201N 1NO-1NC AOFD211N 2NO AOFD220N 2NC AOFD202N 5.5 23 51.5 (1 or 2 blocks) o40 ABFD220N 2NC o35 2NO o25 Momentary 1NO o28.5 Extended with Full Shroud ABFD2 40 17 74.5 (3 or 4 blocks) 2NO-2NC AOFD222N * Round bezel and shroud (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block * Other contact arrangements are also available. See page 67. 69 o30 o30 Diecast Zinc Series Pushbuttons Mushroom / Jumbo Mushroom Types Mushroom ABD3 Momentary Contact Type No. 1NO ABD310N 1NC ABD301N Button Color Code Dimensions (mm) 1NO-1NC ABD311N 2NO ABD320N 2NC ABD302N M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 2NO-2NC ABD322N Maintained 1NO AOD310N 1NC AOD301N AOD320N 2NC AOD302N B: G: R: ABGD310N W: ABGD301N Y: 2NO-2NC AOD322N Mushroom with Full Shroud ABGD3 1NO 1NC Momentary 40 53 (1 or 2 blocks) 1NO-1NC AOD311N 2NO 23 5.5 22 76 (3 or 4 blocks) black green red white yellow 1NO-1NC ABGD311N 2NO ABGD320N 2NC ABGD302N M3.5 Terminal Screw Panel Thickness 0.8 to 6.5 o48 Mushroom AOD3 2NO-2NC ABGD322N Mushroom with Full Shroud AOGD3 1NO 1NC Maintained o40 Operation Type o40 Shape AOGD310N 5.5 AOGD301N AOGD320N 2NC AOGD302N 23 75 (3 or 4 blocks) 1NO-1NC AOGD311N 2NO 23 52 (1 or 2 blocks) 2NO-2NC AOGD322N ABD401N M3.5 Terminal Screw 1NO-1NC ABD411N 2NO ABD420N 2NC ABD402N 5.5 ABGD410N ABGD401N B: DG: 1NO-1NC ABGD411N DR: 2NO ABGD420N G: R: 2NC ABGD402N Y: 2NO-2NC ABGD422N Momentary Jumbo Mushroom with Deep Shroud ABFD4 Momentary 1NO ABFD410N 1NC ABFD401N M3.5 Terminal Screw black dark green dark red green red yellow Panel Thickness 0.8 to 7.5 5.5 23 53 (1 or 2 blocks) 29 76 (3 or 4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 1NO-1NC ABFD411N 2NO 2NC ABFD420N ABFD402N 2NO-2NC ABFD422N * Specify a button color code in place of in the Type No. * Round bezel and shroud (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block * Other contact arrangements are also available. See page 67. 70 29 76 (3 or 4 blocks) 1NO 1NC 23 53 (1 or 2 blocks) 2NO-2NC ABD422N Jumbo Mushroom with Shallow Shroud ABGD4 Panel Thickness 0.8 to 7.5 o65 ABD410N 1NC o65 o75 Momentary 1NO o75 Jumbo Mushroom ABD4 5.5 23 53 (1 or 2 blocks) 76 (3 or 4 blocks) 32.5 o30 Diecast Zinc Series Pushbuttons o30 Pushlock Turn Reset / Push Turn Lock / Pull / Push-Pull / Pin Lock Types 23 5.5 40 2NC AVD302N 53 (1 or 2 blocks) 2NO-2NC AVD322N 76 (3 or 4 blocks) AJD301N 1NO-1NC AJD311N 2NO AJD320N 2NC AJD302N 2NO-2NC AJD322N 1NO AZN310N 1NO-1NC AZN311N 2NO AZN320N 2NC AZN302N 1NO-1NC AYD3111N 2NO AYD3120N 2NC AYD3102N 1NO ABD8P10N 1NC ABD8P01N 1NO-1NC ABD8P11N 2NO ABD8P20N 2NC ABD8P02N 2NO-2NC ABD8P22N * Specify a button color code in place of in the Type No. * Round bezel (metal): Chrome-plated * Pushbuttons with one or three contact blocks contain a dummy block. * Other contact arrangements are also available. See page 67. * Pushlock Turn Reset: Button is maintained when pressed and is reset when turned clockwise. Red buttons only. Note: AVD3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). * Push Turn Lock: Button is locked when turned clockwise in the depressed position and is reset when turned counterclockwise. * Pull: Pulling the button operates the contacts. Up to 2 contact blocks (1 layer) can be mounted on pull switches. * Push-Pull: Button is maintained in both depressed and reset positions. Up to 2 contact blocks (1 layer) can be mounted on AYD31 push-pull switches. * Pin Lock: Button can be locked in either depressed or reset position by inserting the pin. Pad lock with a o5mm pin can also be used to lock the button. Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: G: R: Y: black green red yellow 23 5.5 L H 40 53 (1 or 2 blocks) 24 76 (3 or 4 blocks) Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw B: G: R: S: Y: black green red blue yellow 36 AJD310N 1NC 24 o40 1NO 36 R: red Y: yellow 36 AVD320N PUS AVD311N 2NO o40 1NO-1NC Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 23 5.5 40 53 (1 or 2 blocks) 30.5 Panel Thickness 0.8 to 7.5 M3.5 Terminal Screw 5.5 o40 Pin Lock ABD8P AVD301N 52 Mushroom Push-Pull AYD31 AVD310N 1NC Dimensions (mm) K OC Mushroom Pull AZD3 1NO Button Color Code o40 Mushroom Push Turn Lock AJD3 Type No. o28 Mushroom Pushlock Turn Reset AVD3 Contact o35 Shape 23 53 (1 or 2 blocks) 40 28.5 49 76 (3 or 4 blocks) * Contact Operation Pull Switch (Spring Return) Contact AZD3 Normal Pull 1NO 1NC 1NO-1NC 2NO 2NC Push-Pull Switch (Maintained) Contact AYD31 Push Pull 1NO-1NC 2NO 2NC Note: Pull and push-pull switches can have a maximum of two contact blocks. 71 o30 o30 Diecast Zinc Series Pilot Lights Dome Types Shape Lamp Lamp Receptacle Input Type Dome APD1 APDE1 Type No. BA9S APD199N E12 APDE199N BA9S APD1DN E12 APDE1DN BA9S APD1N E12 APD1N Without Lamp Full Voltage LED Transformer Incandescent Transformer Lens/LED Color Code A: C: G: R: S: W: Y: amber clear green red blue white yellow A: amber G: green PW: pure white (BA9S only) R: red S: blue W: white Y: yellow A: C: G: R: S: W: amber clear green red blue white Applicable Lamp LSTD LS (1W) LETD LE (2W) LSTD-6 LETD-6 LS-6 (1W) LE-8 (2W) * Operating Voltage Code Specify an operating voltage code in place of in the Type No. Operating Voltage Code LED Transformer BA9S and E12 Types Incandescent Transformer E12 Type Incandescent Transformer BA9S Type 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC (incandescent only) 488: 480V AC * Specify a lens/LED color code in place of in the Type No. Use the white lens (W) for LED pure white illumination. * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer and DC-DC converter types contain an LED lamp: LSTD-6 or LETD-6 (rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp: LS-6 (1W, 6V AC/DC) or LE-8 (2W, 18V AC/DC). Dimensions * Full Voltage Type Panel Thickness 0.8 to 7.5 9 29.5 o40 o35 o25 M3.5 Terminal Screw 40 21 * Transformer Type M3.5 Terminal Screw 9 64.5 o40 o35 o25 Panel Thickness 0.8 to 7.5 40 21 All dimensions in mm. 72 o30 Diecast Zinc Series Illuminated Pushbuttons o30 Round Extended Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Round Extended ALD2 AOLD2 Momentary Lamp Input Type Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer BA9S Maintained Contact 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Type No. ALD29911N ALD29920N ALD29902N ALD211DN ALD220DN ALD202DN ALD211N ALD220N ALD202N AOLD29911N AOLD29920N AOLD29902N AOLD211DN AOLD220DN AOLD202DN AOLD211N AOLD220N Applicable Lamp LSTD LS (1W) LSTD-6 LS-6 LSTD LS (1W) LSTD-6 LS-6 AOLD202N * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: amber G: green PW: pure white R: red S: blue W: white Y: yellow Lens Color Code Operating Voltage Code Incandescent Illuminated Type Specify a lens color code in place of in Specify an operating voltage code in place of in the Type No. the Type No. A: amber 16: 100/110V AC C: clear 116: 115V AC G: green 126: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 246: 240V AC 386: 380V AC 46: 400/440V AC Use the white lens (W) for LED pure white 486: 480V AC (incandescent only) illumination. * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W). Dimensions * ALD2/AOLD2 Full Voltage * ALD2/AOLD2 BA9S/Transformer M3.5 Terminal Screw M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 23 24 o40 o24 40 40 9 9 63 (2 blocks) 86 (4 blocks) o35 o40 o35 o24 5.5 Panel Thickness 0.8 to 7.5 M3 Terminal Screw M3 Terminal Screw 97.5 (2 blocks) 120.5 (4 blocks) 24 All dimensions in mm. 73 o30 o30 Diecast Zinc Series Illuminated Pushbuttons Round Extended with Full Shroud Illuminated Pushbuttons Lamp Receptacle Shape Operation Type Round Extended with Full Shroud ALFD2 AOLFD2 Momentary Lamp Input Type Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer BA9S Maintained Applicable Lamp Contact Type No. 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC ALFD29911N ALFD29920N ALFD29902N ALFD211DN ALFD220DN ALFD202DN ALFD211N ALFD220N ALFD202N AOLFD29911N AOLFD29920N AOLFD29902N AOLFD211DN AOLFD220DN AOLFD202DN AOLFD211N AOLFD220N AOLFD202N LSTD LS (1W) LSTD-6 LS-6 LSTD LS (1W) LSTD-6 LS-6 * Color Code and Operating Voltage Code Lens/LED Color Code Lens Color Code Operating Voltage Code Incandescent Illuminated Type Specify a lens color code in place of in Specify an operating voltage code in place of in the Type No. the Type No. A: amber 16: 100/110V AC C: clear 116: 115V AC G: green 126: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 246: 240V AC 386: 380V AC 46: 400/440V AC Use the white lens (W) for LED pure white 486: 480V AC (incandescent only) illumination. LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: amber G: green PW: pure white R: red S: blue W: white Y: yellow * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W) Dimensions * ALFD2/AOLFD2 Full Voltage * ALFD2/AOLFD2 Transformer M3 Terminal Screw M3 Terminal Screw 23 62 (2 blocks) 84 (4 blocks) Panel Thickness 0.8 to 6 40 40 25 o40 o40 o30 o35 5.5 M3.5 Terminal Screw Panel Thickness 0.8 to 6 o30 o35 M3.5 Terminal Screw 96.5 (2 blocks) 119.5 (4 blocks) 25 All dimensions in mm. 74 o30 Diecast Zinc Series Illuminated Pushbuttons o30 Mushroom (o40) Illuminated Pushbuttons Lamp Receptacle Shape Operation Type o40 Mushroom ALD3 AOLD3 Lamp Input Type Without Lamp Full Voltage LED Transformer Without Lamp Full Voltage LED Transformer Momentary BA9S Maintained Contact 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Type No. ALD39911DN ALD39920DN ALD39902DN ALD311DN ALD320DN ALD302DN AOLD39911DN AOLD39920DN AOLD39902DN AOLD311DN AOLD320DN AOLD302DN Applicable Lamp LSTD LSTD-6 LSTD LSTD-6 * Color Code and Operating Voltage Code Lens/LED Color Code LED Illuminated Type Specify a lens/LED color code in place of in the Type No. A: G: R: W: Y: amber green red white yellow Operating Voltage Code LED Transformer BA9S Type Specify an operating voltage code in place of in the Type No. 16: 116: 126: 26: 236: 246: 386: 46: 100/110V AC 115V AC 120V AC 200/220V AC 230V AC 240V AC 380V AC 400/440V AC * Full voltage types do not contain a lamp. Order LED lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). Dimensions * ALD3/AOLD3 Full Voltage * ALD3/AOLD3 Transformer M3.5 Terminal Screw 5.5 Panel Thickness 0.8 to 7.5 40 24 36 36 o40 M3 Terminal Screw 23 63 (2 blocks) 86 (4 blocks) M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 o40 M3 Terminal Screw 40 97.5 (2 blocks) 120.5 (4 blocks) 24 All dimensions in mm. 75 o30 o30 Diecast Zinc Series Illuminated Pushbuttons Mushroom Pushlock Turn Reset Types Lamp Receptacle Shape Lamp Mushroom Pushlock Turn Reset AVLD3 AVLDE3 BA9S E12 Input Type Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Contact 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC 1NO-1NC 2NO 2NC Applicable Lamp Type No. AVLD39911NR AVLD39920NR AVLD39902NR AVLD311DNR AVLD320DNR AVLD302DNR AVLD311NR AVLD320NR AVLD302NR AVLDE39911NR AVLDE39920NR AVLDE39902NR AVLDE311DNR AVLDE320DNR AVLDE302DNR AVLD311NR AVLD320NR AVLD302NR LSTD LS (1W) LSTD-6 LS-6 LETD LE (2W) LETD-6 LE-8 * Operating Voltage Code Operating Voltage Code LED Transformer BA9S and E12 Types Incandescent Transformer E12 Type Incandescent Transformer BA9S Type 16: 100/110V AC 18: 100/110V AC 116: 115V AC 118: 115V AC 126: 120V AC 128: 120V AC 26: 200/220V AC 28: 200/220V AC 236: 230V AC 238: 230V AC 246: 240V AC 248: 240V AC 386: 380V AC 388: 380V AC 46: 400/440V AC 48: 400/440V AC 486: 480V AC (incandescent only) 488: 480V AC * Color code: R (red) * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC, 1W) * Pushlock Turn Reset: Lens is maintained when pressed and is reset when turned clockwise. Red lens only. * Note: AVLD3 and AVLDE3 pushlock turn reset switches cannot be used as emergency stop switches. When emergency stop switches are required, use the HN1E series emergency stop switches (ISO 13850 and IEC 60947-5-5 compliant). Dimensions * AVLD3 BA9S/Transformer * AVLD3 BA9S/Full Voltage Panel Thickness 0.8 to 7.5 23 M3.5 Terminal Screw Panel Thickness 0.8 to 7.5 36 Panel Thickness 0.8 to 7.5 M3 Terminal Screw 23 77.5 (2 blocks) 100.5 (4 blocks) 40 24 * AVLD3/AVLDE3 E12/Transformer 36 o40 5.5 23 97.5 (2 blocks) 120.5 (4 blocks) * AVLDE3 E12/Full Voltage M3.5 Terminal Screw M3 Terminal Screw o40 36 5.5 40 24 40 20 36 63 (2 blocks) 86 (4 blocks) Panel Thickness 0.8 to 7.5 o40 5.5 M3.5 Terminal Screw M3 Terminal Screw o40 M3.5 Terminal Screw M3 Terminal Screw 40 112 (2 blocks) 135 (4 blocks) 20 All dimensions in mm. 76 o30 Diecast Zinc Series Selector Switches o30 No. of Positions ASD Selector Switches (Knob Operator Type) Shape ASD Contact Arrangement Chart 90 2-position Contact Code (ASD) 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) Contact Code (ASD) 20 45 3-position (2NO) 40 (4NO) 22 (2NO-2NC) 02 (2NC) 04 (4NC) Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 Type Maintained Operator Position L L R NO Dummy NO NC NO NO NO NC NO NC Contact Block L R Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC C L R ASD2110N ASD2210N ASD211N ASD2111N ASD2211N ASD220N ASD2120N ASD2220N ASD222N ASD2122N ASD2222N Maintained Operator Position L R ASD210N L R L Spring Return Two-way C C C R -- Spring Return from Left Spring Return from Right C Mounting Position Spring Return from Left Spring Return from Right L R L R ASD320N ASD3120N ASD3220N ASD3320N ASD340N ASD3140N ASD3240N ASD3340N ASD322N ASD3122N ASD3222N ASD3322N ASD302N ASD3102N ASD3202N ASD3302N ASD304N ASD3104N ASD3204N ASD3304N R * Knob: Black * Round bezel (metal): Chrome-plated * Selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] * Dimensions Center Left 4 2 1 Panel Thickness 0.8 to 7.5 90 M3.5 Terminal Screw 1 2 3 4 NO NO NC NC C R 45 Operator Position o35 L 3 Right 5.5 23 53 (1 or 2 blocks) 45 o40 * Contact Block Mounting Position and Contact Arrangement Chart 40 21 76 (3 or 4 blocks) All dimensions in mm. 77 o30 o30 Diecast Zinc Series Selector Switches No. of Positions ASD Selector Switches (Lever Operator Type) Shape ASDL Contact Arrangement Chart 90 2-position Contact Code (ASD) 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) Contact Code (ASD) 20 45 3-position (2NO) 40 (4NO) 22 (2NO-2NC) 02 (2NC) 04 (4NC) Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 Type L L R NO Dummy NO NC NO NO NO NC NO NC Contact Block Maintained Operator Position L R Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC C L R ASD21L10N ASD22L10N ASD2L11N ASD21L11N ASD22L11N ASD2L20N ASD21L20N ASD22L20N ASD2L22N ASD21L22N ASD22L22N Maintained Operator Position L R ASD2L10N L R Spring Return Two-way C C C R -- Spring Return from Left Spring Return from Right C Mounting Position Spring Return from Left Spring Return from Right L L R L R ASD3L20N ASD31L20N ASD32L20N ASD33L20N ASD3L40N ASD31L40N ASD32L40N ASD33L40N ASD3L22N ASD31L22N ASD32L22N ASD33L22N ASD3L02N ASD31L02N ASD32L02N ASD33L02N ASD3L04N ASD31L04N ASD32L04N ASD33L04N R * Lever: Black * Round bezel (metal): Chrome-plated * Selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] * Dimensions Center Left 4 2 1 Panel Thickness 0.8 to 7.5 90 M3.5 Terminal Screw 1 2 3 4 NO NO NC NC C R 45 Operator Position o35 L 3 Right 5.5 45 o40 * Contact Block Mounting Position and Contact Arrangement Chart 23 53 (1 or 2 blocks) 40 21.5 76 (3 or 4 blocks) All dimensions in mm. 78 o30 Diecast Zinc Series Selector Switches o30 No. of Positions ASD Key Selector Switches Shape ASDK Contact Arrangement Chart 90 2-position Contact Code (ASD) Contact Block Mounting Position 1 2 1 2 1 2 1 2 3 4 10 (1NO) 11 (1NO-1NC) 20 (2NO) 22 (2NO-2NC) Contact Code (ASD) L L R NO Dummy NO NC NO NO NO NC NO NC Contact Block L R Type 1 2 1 2 3 4 1 2 3 4 1 2 1 2 3 4 NO NO NO NO NO NO NO NO NC NC NC NC NC NC NC NC 20 40 (4NO) 22 (2NO-2NC) 02 (2NC) 04 (4NC) C R L R ASD2K10N ASD21K10N ASD22K10N ASD2K11N ASD21K11N ASD22K11N ASD2K20N ASD21K20N ASD22K20N ASD2K22N ASD21K22N ASD22K22N Maintained Operator Position L Spring Return from Left Spring Return from Right L R Spring Return Two-way C C C R -- Spring Return from Left Spring Return from Right C Mounting Position (2NO) 45 3-position Type Maintained Operator Position L L R L R ASD3K20N ASD31K20N ASD32K20N ASD33K20N ASD3K40N ASD31K40N ASD32K40N ASD33K40N ASD3K22N ASD31K22N ASD32K22N ASD33K22N ASD3K02N ASD31K02N ASD32K02N ASD33K02N ASD3K04N ASD31K04N ASD32K04N ASD33K04N R * Cylinder: Black * Round bezel (metal): Chrome-plated * On the spring-returned types, the keys can be released only from the maintained positions. On the maintained types, the key can be released from every position. Key retained positions are also available. See page 12. * Key selector switches are supplied with two standard keys. * Key selector switches with one contact block contain a dummy block. * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] L 3 1 1 2 3 4 NO NO NC NC Panel Thickness 0.8 to 7.5 Center Left 2 C Right R 90 M3.5 Terminal Screw 45 Operator Position 45 o35 4 * Dimensions 5.5 23 9 53 (1 or 2 blocks) 16.5 o40 * Contact Block Mounting Position and Contact Arrangement Chart 40 38 76 (3 or 4 blocks) All dimensions in mm. 79 o30 o30 Diecast Zinc Series Illuminated Selector Pushbuttons Illuminated Selector Switches 90 2-position Shape ASLD (Base BA9S) Contact Arrangement Chart Contact Code Contact Block Maintained Operator Position Lamp Input Type L Spring Return from Right L R Spring Return from Left R L R Mounting Position Type 1 NO Without Lamp Full Voltage ASLD29911N ASLD219911N ASLD229911N 2 NC LED Transformer ASLD211DN ASLD2111DN ASLD2211DN Incandescent Transformer ASLD211N ASLD2111N ASLD2211N 11 (1NO-1NC) 20 (2NO) 22 R 1 NO Without Lamp Full Voltage ASLD29920N ASLD219920N ASLD229920N 2 NO LED Transformer ASLD220DN ASLD2120DN ASLD2220DN Incandescent Transformer ASLD220N ASLD2120N ASLD2220N Without Lamp Full Voltage ASLD29922N ASLD219922N ASLD229922N LED Transformer ASLD222DN ASLD2122DN ASLD2222DN Incandescent Transformer ASLD222N ASLD2122N ASLD2222N 1 2 3 4 (2NO-2NC) L NO NC NO NC * Color Code and Operating Voltage Code LED Illuminated Type Lens/LED Color Code Specify a lens/LED color code in place of in the Type No. A: G: R: S: W: Y: Incandescent Illuminated Type Operating Voltage Code Lens Color Code Specify a lens color code in place of Specify an operating voltage code in place of in the Type No. in the Type No. 16: 100/110V AC A: amber 156: 115V AC G: green 136: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 256: 240V AC 386: 380V AC 46: 400/440V AC 486: 480V AC (incandescent only) amber green red blue white yellow * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). * On the 2-position selector switches marked with above, the contact operation is reversed as follows. [Example] * Contact Block Mounting Position and Contact Arrangement Chart * Dimensions 3 1 L 1 2 3 4 NO NC NO NC R M3 Terminal Screw Panel Thickness 0.8 to 7.5 (including nameplate) Operator Position 5.5 90 4 5 45 o40 2 M3.5 Terminal Screws o35 4 Right o25 Left 40 23 63 (2 blocks) 9 A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) 28 A: Full voltage type B: Transformer type All dimensions in mm. 80 o30 Diecast Zinc Series Illuminated Selector Pushbuttons o30 Illuminated Selector Switches 45 3-position Contact Code Contact Block Mounting Position Type 1 NO 2 NO 20 (2NO) 02 (2NC) 22 (2NO-2NC) 40 (4NO) 04 (4NC) 1 NC 2 NC 1 2 3 4 NO NO NC NC 1 2 3 4 NO NO NO NO 1 2 3 4 NC NC NC NC Maintained Operator Position L C Lamp Input Type R Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Without Lamp Full Voltage LED Transformer Incandescent Transformer Spring Return from Right C L Spring Return from left C R Spring Return Two-way C C R L L R L R ASLD39920N ASLD319920N ASLD329920N ASLD339920N ASLD320DN ASLD3120DN ASLD3220DN ASLD3320DN ASLD320N ASLD3120N ASLD3220N ASLD3320N ASLD39902N ASLD319902N ASLD329902N ASLD339902N ASLD302DN ASLD3102DN ASLD3202DN ASLD3302DN ASLD302N ASLD3102N ASLD3202N ASLD3302N ASLD39922N ASLD319922N ASLD329922N ASLD339922N ASLD322DN ASLD3122DN ASLD3222DN ASLD3322DN ASLD322N ASLD3122N ASLD3222N ASLD3322N ASLD39940N ASLD319940N ASLD329940N ASLD339940N ASLD340DN ASLD3140DN ASLD3240DN ASLD3340DN ASLD340N ASLD3140N ASLD3240N ASLD3340N ASLD39904N ASLD319904N ASLD329904N ASLD339904N ASLD304DN ASLD3104DN ASLD3204DN ASLD3304DN ASLD304N ASLD3104N ASLD3204N ASLD3304N * Color Code and Operating Voltage Code LED Illuminated Type Lens/LED Color Code Specify a lens/LED color code in place of in the Type No. A: G: R: S: W: Y: amber green red blue white yellow Incandescent Illuminated Type Operating Voltage Code Lens Color Code Specify a lens color code in place of Specify an operating voltage code in place of in the Type No. in the Type No. 16: 100/110V AC A: amber 156: 115V AC G: green 136: 120V AC R: red 26: 200/220V AC S: blue 236: 230V AC W: white 256: 240V AC 386: 380V AC 46: 400/440V AC 486: 480V AC (incandescent only) * Full voltage types do not contain a lamp. Order LED or incandescent lamps separately. For lamps, see page 63. * LED illuminated transformer types contain an LED lamp (LSTD-6, rated voltage 6V AC/DC). * Incandescent illuminated transformer types contain an incandescent lamp (LS-6, rated voltage 6V AC/DC). * Contact Block Mounting Position and Contact Arrangement Chart Center Left 1 M3.5 Terminal Screws M3 Terminal Screw Panel Thickness 0.8 to 7.5 (including nameplate) 90 4 5 45 1 2 3 4 NO NO NC NC R Operator Position 5.5 o40 C o35 2 L 3 Right o25 4 * Dimensions 40 23 63 (2 blocks) 9 A: 86 (4 blocks) B: 97.5 (2 blocks), 120.5 (4 blocks) 28 A: Full voltage type B: Transformer type All dimensions in mm. 81 o30 o30 Diecast Zinc Series Selector Pushbutton Switches Ring Operator Type / Lever Operator Type Selector Pushbuttons Ring/Lever Shape Ring Operator Contact Block Contact Circuit Code Code Lever Operator Color Pushbutton Ring Operator (90 2-Position) ASBD2 Mounting Position Type 1 2 1 2 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 NO NC NO NC NO NC NO NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC NO NO NC NC A03 11 (1NO-1NC) G03 A08 C10 Lever Operator (90 2-Position) ASBD2L D10 22 (2NO-2NC) E10 F10 G10 Normal Push Normal Type No. Push Type No. ASBD211N-A03 ASBD2L11N-A03 Blocked ASBD211N-G03 ASBD2L11N-G03 ASBD222N-A08 ASBD2L22N-A08 ASBD222N-C10 ASBD2L22N-C10 B: black G: green ASBD222N-D10 ASBD2L22N-D10 R: red Y: yellow ASBD222N-E10 ASBD2L22N-E10 ASBD222N-F10 Blocked ASBD2L22N-F10 ASBD222N-G10 ASBD2L22N-G10 * Specify a button color code in place of in the Type No. * Ring/Lever (Metal): Chrome-plated Notes : 1. Circuit Code G: The pushbutton does not operate when the ring or lever operator is turned to the right position. 2. Circuit Codes E and F: The right and left NC contact blocks on circuit code E or F may overlap each other while turning the ring or lever operator. The NO and NC contact blocks on circuit code F may overlap each other while pressing the button. 3. When using the selector pushbutton, do not turn the ring or lever operator with the pushbutton depressed. Otherwise, damage or failure may be caused. 4. When installing the lever operator, make sure that the lever is not in the horizontal position. Otherwise, shock resistance may be degraded. * Contact Block Mounting Position and Contact Arrangement Chart Normal Push 1 2 3 4 1 * Dimensions Panel Thickness 0.8 to 7.5 (including nameplate) 5.5 82 23 53 (2 blocks) 76 (4 blocks) o40 Lever Operator (90 2-position) ASBD2L M3.5 Terminal Screw 37 5.5 23 53 (1 or 2 blocks) 40 25 Panel Thickness 0.8 to 7.5 (including nameplate) o34 20 M3.5 Terminal Screw o28 o35 Ring Operator (90 2-position) ASBD2 26.5 R50 3 2 50 4 76 (3 or 4 blocks) M3 Setscrew (The actual screw is located on the opposite side) 37 o30 Diecast Zinc Series Accessories and Replacement Parts o30 Accessories (For Diecast Zinc Series Only) Shape Material For other accessories, see pages 55 to 63. Ordering Type No. Type No. Package Quantity Description Metal Bezel OG-81 OG-81PN02 2 * Cannot be used with half-shrouds. Chrome-plated Flush (Octagonal) Spare Key Extended (Octagonal) Metal OG-82 OG-82 1 TW-SK-0 TW-SK-0PN02 2 * For key selector switches Maintenance Parts (For Diecast Zinc Series Only) Shape Button Specification Mushroom Plastic Flush Extended Dummy Block Selector Operator Knob Ordering Type No. ABN1BN-PN05 5 ABN2BN- ABN2BN-PN05 5 ABN3BN- ABN3BN-PN02 2 BST-D BST-DPN10 10 * Used for 1NO or 1NC contact blocks. * Snaps on to the operator unit. ASNHT- ASNHT-PN02 2 Specify a color code in place of . B (blue), G (green), R (red) 5 Specify a color code in place of . B (black), G (green), R (red), S (blue), W (white), Y (yellow) Color Insert Description ABN1BN- Plastic Color Insert Package Quantity Plastic Lever Type No. ASNHL- ASNHL-PN02 TW-HC1 TW-HC1PN05 Specify a color code in place of . B (black), G (green), R (red), S (blue), W (white), Y (yellow) * Above colors are used for o30 diecast zinc control units (light colored operator units). Safety Precautions * Turn off the power to the o30 diecast zinc control units before starting installation, removal, wiring, maintenance, and starting installation, removing, wiring, maintenance, and inspection of the products. Failure to turn power off may cause electrical shocks or fire hazard. * To avoid a burn on your hand, use the lamp holder tool when replacing lamps. * For wiring, use wires of a proper size to meet the voltage and current requirements. Tighten the M3.5 terminal screws to a tightening torque of 1.0 to 1.3 N*m. Failure to tighten terminal screws may cause overheat and fire. Instructions Tightening Torque for Terminal Screws Installation of LED Illuminated Units Tighten the M3.5 terminal screws to a torque of 1.0 to 1.3 N*m. * When using full voltage type LED illuminated units, provide protection against electrical noise, if necessary. See page 65 for notes on LED illuminated units. Replacement of Lamps Lamps can be replaced by using the lamp holder tool (OR55) from the front of the panel. * How to remove To remove, slip the lamp holder tool onto the lamp head lightly. Then push slightly, and turn the lamp holder tool counterclockwise. * How to install To install, insert the lamp head into the lamp holder tool. Place the pins on the lamp base to the grooves in the lamp socket. Inset the lamp and turn it clockwise. OR-55 83 Specifications and other descriptions in this catalog are subject to change without notice. 7-31, Nishi-Miyahara 1-Chome, Yodogawa-ku, Osaka 532-8550, Japan Tel: +81-6-6398-2571, Fax: +81-6-6392-9731 www.idec.com IDEC CORPORATION (USA) IDEC IZUMI ASIA PTE. LTD. 1175 Elko Drive, Sunnyvale, CA 94089-2209, USA Tel: +1-408-747-0550, Toll Free: (800) 262-IDEC, Fax: +1-408-744-9055 E-mail: opencontact@idec.com, www.idec.com No. 31, Tannery Lane #05-01, Dragon Land Building, Singapore 347788 Tel: +65-6746-1155, Fax: +65-6844-5995 E-mail: generalinfo@idecasia.com.sg IDEC CANADA LIMITED IDEC IZUMI (H.K.) CO., LTD. Unit 22-151, Brunel Road Mississauga, Ontario, L4Z 1X3, Canada Tel: +1-905-890-8561, Toll Free: (888) 317-4332, Fax: +1-905-890-8562 Unit 1505-07, DCH Commercial Centre No. 25, Westlands Road, Quarry Bay, Hong Kong Tel: +852-2803-8989, Fax: +852-2565-0171 E-mail: idec@idechk.com IDEC ELECTRONICS LIMITED Unit 2, Beechwood, Chineham Business Park, Basingstoke, Hampshire RG24 8WA, UK Tel: +44-1256-321000, Fax: +44-1256-327755 E-mail: idec@uk.idec.com IDEC ELEKTROTECHNIK GmbH Wendenstrasse 331, D-20537 Hamburg, Germany Tel: +49-40-25 30 54 10, Fax: +49-40-25 30 54 24 E-mail: service@idec.de, www.idec.de IDEC AUSTRALIA PTY. LTD. 2/3 Macro Court, Rowville, Victoria 3178, Australia Toll Free: 1-800-68-4332, Fax: +61-3-9763-3255 E-mail: sales@au.idec.com IDEC IZUMI (Shanghai) Co., Ltd. Room E, 15F, Majesty Building, No. 138 Pudong Avenue, Shanghai 200120, P.R.C. Tel: +86-21-5887-9181, Fax: +86-21-5887-8930 E-mail: idec@cn.idec.com IDEC TAIWAN CORPORATION 8F, No. 79, Hsin Tai Wu Road, Sec. 1, Hsi-Chih, Taipei County, Taiwan Tel: +886-2-2698-3929, Fax: +886-2-2698-3931 E-mail: service@idectwn.com.tw Cat. No. EP1078-0 MARCH 2005 13DNP PRINTED IN JAPAN