G691L293T93 - Global Mixed-Mode Technology, Inc.

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Microprocessor Reset IC

Features



Precision Monitoring of +3V, +3.3V, and +5V

Power-Supply Voltages



Fully Specified Over Temperature



Available in Three Output Configurations

Push-Pull RESET Output (G690L)

Push-Pull RESET Output (G690H)

Open-Drain RESET Output (G691L)



140ms min Power-On Reset Pulse Width



10µA Supply Current



Guaranteed Reset Valid to VCC = +1V



Power Supply Transient Immunity



No External Components



3-Pin SOT89, SOT23 and SC70 Packages

Applications



Computers



Controllers



Intelligent Instruments



Critical µP and µC Power Monitoring



Portable / Battery-Powered Equipment



Automotive

General Description

The G690/G691 are microprocessor (µP) supervisory

circuits used to monitor the power supplies in µP and

digital systems. They provide excellent circuit reliability

and low cost by eliminating external components and

adjustments when used with +5V, +3.3V, +3.0V- pow-

ered circuits.

These circuits perform a single function: they assert a

reset signal whenever the VCC supply voltage declines

below a preset threshold, keeping it asserted for at

least 140ms after VCC has risen above the reset

threshold. Reset thresholds suitable for operation with

a variety of supply voltages are available.

The G691L has an open-drain output stage, while the

G690 have push-pull outputs. The G691L’s open-drain

RESET output requires a pull-up resistor that can be

connected to a voltage higher than VCC. The G690L

have an active-low RESET output, while the G690H

has an active-high RESET output. The reset com-

parator is designed to ignore fast transients on VCC,

and the outputs are guaranteed to be in the correct

logic state for VCC down to 1V.

Low supply current makes the G690/G691 ideal for

use in portable equipment. The G690/G691 are avail-

able in 3-pin SOT89 or SOT23 or SC70 packages.

Pin Configuration Typical Application







RESET

INPUT

GND

µP

VCC

RESET

(RESET)

GND

G690/G691

VCC

RPULL-UP

VCC

*G691 ONLY

SOT23/SC70

SOT 89

RESET

INPUT

GND

µP

VCC

RESET

(RESET)

GND

G690/G691

VCC

RPULL-UP

VCC

*G691 ONLY

SOT23/SC70

SOT 89

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Ordering Information

PART TEMP. RANGE OUTPUT TYPE

G690LxxxTxx -40°C ~ +105°C Push-Pull Active Low

G690HxxxTxx -40°C ~ +105°C Push-Pull Active High

G691LxxxTxx -40°C ~ +105°C Open-Drain

Order Number Identification

G69XX XXX TX X

Pin Option

Package Type

Threshold Voltage Option

Part Number

PART NUMBER THRESHOLD VOLTAGE OPTION

G690L : Push-Pull Active Low Output * xxx specifies the threshold voltage.

G690H : Push-Pull Active High Output e.g. 263 denotes the 2.63V threshold voltage.

G691L : Open-Drain Output

PACKAGE TYPE PIN OPTION

T2 : SOT 89 1 2 3

T7 : SOT 23 1 : RESET GND VCC

T9 : SC 70 2 : RESET VCC GND

3 : GND RESET VCC

4 : GND VCC RESET

5 : VCC GND RESET

6 : VCC RESET GND

*RESET for G690H

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Absolute Maximum Ratings

Terminal Voltage (with respect to GND)

VCC.……………………………..…….…….-0.3V to +6.0V

RESET, RESET (push-pull)....…....-0.3V to (VCC + 0.3V)

RESET (open drain)...….......................-0.3V to +6.0V

Input Current, VCC ............................….................20mA

Output Current, RESET, RESET ........................20mA

Continuous Power Dissipation (TA = +70°C)

3-Pin SOT89……………………………………….500mW

3-Pin SOT23 (derate 4mW/°C above +70°C)….320mW

3-Pin SC70 (derate 2.17mW/°C above +70°C)..174mW

Operating Temperature Range …........-40°C to +105°C

Storage Temperature Range..….….….-65°C to +150°C

Lead Temperature (soldering, 10s) ..…....…......+300°C

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress rat-

ings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of

the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics

(VCC = full range, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C, VCC = 5V

for 463/438/400 versions, VCC= 3.3V for 308/293 versions, and VCC = 3V for 263 version.) (Note 1)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

A = 0°C +70°C 1.0 5.5

VCC Range

A = -40°C +105°C 1.2 5.5 V

CC<5.5V, G69_ _463/438/400_ 22 30

Supply Current (SOT23) ICC T

A = -40°C +105°C

CC<3.6V, G69_ _308/293/263_ 10 23 µA

A = +25°C 4.56 4.63 4.70

A = -40°C to +85°C 4.50 4.75

G69_ _463_

A = +85°C to +105°C 4.40 4.86

A = +25°C 4.31 4.38 4.45

A = -40°C to +85°C 4.25 4.50

G69_ _438_

A = +85°C to +105°C 4.16 4.56

A = +25°C 3.93 4.00 4.06

A = -40°C to +85°C 3.89 4.10

G69_ _400_

A = +85°C to +105°C 3.80 4.20

A = +25°C 3.04 3.08 3.11

A = -40°C to +85°C 3.00 3.15

G69_ _308_

A = +85°C to +105°C 2.92 3.23

A = +25°C 2.89 2.93 2.96

A = -40°C to +85°C 2.85 3.00

G69_ _293_

A = +85°C to +105°C 2.78 3.08

A = +25°C 2.59 2.63 2.66

A = -40°C to +85°C 2.55 2.70

Reset Threshold VTH

G69_ _263_

A = +85°C to +105°C 2.50 2.76

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Electrical Characteristics (Continued)

(VCC = full range, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C, VCC = 5V

for 463/438/400 versions, VCC= 3.3V for 308/293 versions, and VCC = 3V for 263 version.) (Note 1)

PARAMETER SYMBOL CONDITION MIN TYP MAX UNITS

Reset Threshold Tempco 40 ppm/°C

VCC to Reset Delay (Note 2) VCC = VTH to (VTH – 100mV) 7 µs

VCC = VTH max,

G69_ _ 463/438/400 280 640

Reset Active Timeout Period

VCC = VTH max,

G69_ _308/293/263 140 550

RESET Output Current Low (push-pull active low,

and open-drain active-low, G690L and G691L) IOL VCC = 2.5V, V RESET = 0.5V 8 mA

VCC = 5V, V RESET = 4.5V,

G690L463/438/400 4.5

VCC = 3.3V, V RESET = 2.8V,

G690L308/293 3

RESET Output Current High (push-pull active

low, G690L) IOH

VCC = 3V, V RESET = 2.5V,

G690L263 2

VCC = 5V, VRESET = 0.5V,

G690H463/438/400 16

VCC = 3.3V, VRESET = 0.5V,

G690H308/293 12

RESET Output Current Low (push-pull active

high, G690H) IOL

VCC = 3V, VRESET = 0.5V,

G690H263 10

RESET Output Current High (push-pull active

high, G690H) IOH V

CC = 2.5V, VRESET = 2V 2 mA

RESET Open-Drain Output Leakage Current

(G691L) VCC > VTH, RESET deasserted 1 µA

Note 1: Production testing done at TA = +25°C; limits over temperature guaranteed by design.

Note 2: RESET output is for G690L/G691L; While RESET output is for G690H.

Selector Guide

TOP MARK

PART/SUFFIX RESET THRESHOLD (V) OUTPUT TYPE SOT 89 SOT 23 SC70

G691L463Tx1 4.63 Open-Drain 689Fx 689Fx 689Fx

G691L438Tx1 4.38 Open-Drain 689Ex 689Ex 689Ex

G691L400Tx1 4.00 Open-Drain 689Dx 689Dx 689Dx

G691L308Tx1 3.08 Open-Drain 689Cx 689Cx 689Cx

G691L293Tx1 2.93 Open-Drain 689Bx 689Bx 689Bx

G691L263Tx1 2.63 Open-Drain 689Ax 689Ax 689Ax

G690H463Tx1 4.63 Push-Pull RESET 688Lx 688Lx 688Lx

G690H438Tx1 4.38 Push-Pull RESET 688Kx 688Kx 688Kx

G690H400Tx1 4.00 Push-Pull RESET 688Jx 688Jx 688Jx

G690H308Tx1 3.08 Push-Pull RESET 688Ix 688Ix 688Ix

G690H293Tx1 2.93 Push-Pull RESET 688Hx 688Hx 688Hx

G690H263Tx1 2.63 Push-Pull RESET 688Gx 688Gx 688Gx

G690L463Tx1 4.63 Push-Pull 688Fx 688Fx 688Fx

G690L438Tx1 4.38 Push-Pull 688Ex 688Ex 688Ex

G690L400Tx1 4.00 Push-Pull 688Dx 688Dx 688Dx

G690L308Tx1 3.08 Push-Pull 688Cx 688Cx 688Cx

G690L293Tx1 2.93 Push-Pull 688Bx 688Bx 688Bx

G690L263Tx1 2.63 Push-Pull 688Ax 688Ax 688Ax

Note: T2: SOT89; T7: SOT23; T9: SC70

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Selector Guide

TOP MARK

PART/SUFFIX RESET THRESHOLD (V) OUTPUT TYPE SOT 89 SOT 23 SC70

G691L463Tx2 4.63 Open-Drain 687Fx 687Fx 687Fx

G691L438Tx2 4.38 Open-Drain 687Ex 687Ex 687Ex

G691L400Tx2 4.00 Open-Drain 687Dx 687Dx 687Dx

G691L308Tx2 3.08 Open-Drain 687Cx 687Cx 687Cx

G691L293Tx2 2.93 Open-Drain 687Bx 687Bx 687Bx

G691L263Tx2 2.63 Open-Drain 687Ax 687Ax 687Ax

G690H463Tx2 4.63 Push-Pull RESET 686Lx 686Lx 686Lx

G690H438Tx2 4.38 Push-Pull RESET 686Kx 686Kx 686Kx

G690H400Tx2 4.00 Push-Pull RESET 686Jx 686Jx 686Jx

G690H308Tx2 3.08 Push-Pull RESET 686Ix 686Ix 686Ix

G690H293Tx2 2.93 Push-Pull RESET 686Hx 686Hx 686Hx

G690H263Tx2 2.63 Push-Pull RESET 686Gx 686Gx 686Gx

G690L463Tx2 4.63 Push-Pull 686Fx 686Fx 686Fx

G690L438Tx2 4.38 Push-Pull 686Ex 686Ex 686Ex

G690L400Tx2 4.00 Push-Pull 686Dx 686Dx 686Dx

G690L308Tx2 3.08 Push-Pull 686Cx 686Cx 686Cx

G690L293Tx2 2.93 Push-Pull 686Bx 686Bx 686Bx

G690L263Tx2 2.63 Push-Pull 686Ax 686Ax 686Ax

Note: T2: SOT89; T7: SOT23; T9: SC70

Selector Guide

TOP MARK

PART/SUFFIX RESET THRESHOLD (V) OUTPUT TYPE SOT 89 SOT 23 SC70

G691L463Tx3 4.63 Open-Drain 691Fx 691Fx 691Fx

G691L438Tx3 4.38 Open-Drain 691Ex 691Ex 691Ex

G691L400Tx3 4.00 Open-Drain 691Dx 691Dx 691Dx

G691L308Tx3 3.08 Open-Drain 691Cx 691Cx 691Cx

G691L293Tx3 2.93 Open-Drain 691Bx 691Bx 691Bx

G691L263Tx3 2.63 Open-Drain 691Ax 691Ax 691Ax

G690H463Tx3 4.63 Push-Pull RESET 690Lx 690Lx 690Lx

G690H438Tx3 4.38 Push-Pull RESET 690Kx 690Kx 690Kx

G690H400Tx3 4.00 Push-Pull RESET 690Jx 690Jx 690Jx

G690H308Tx3 3.08 Push-Pull RESET 690Ix 690Ix 690Ix

G690H293Tx3 2.93 Push-Pull RESET 690Hx 690Hx 690Hx

G690H263Tx3 2.63 Push-Pull RESET 690Gx 690Gx 690Gx

G690L463Tx3 4.63 Push-Pull 690Fx 690Fx 690Fx

G690L438Tx3 4.38 Push-Pull 690Ex 690Ex 690Ex

G690L400Tx3 4.00 Push-Pull 690Dx 690Dx 690Dx

G690L308Tx3 3.08 Push-Pull 690Cx 690Cx 690Cx

G690L293Tx3 2.93 Push-Pull 690Bx 690Bx 690Bx

G690L263Tx3 2.63 Push-Pull 690Ax 690Ax 690Ax

Note: T2: SOT89; T7: SOT23; T9: SC70

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Selector Guide

TOP MARK

PART/SUFFIX RESET THRESHOLD (V) OUTPUT TYPE SOT 89 SOT 23 SC70

G691L463Tx6 4.63 Open-Drain 685Fx 685Fx 685Fx

G691L438Tx6 4.38 Open-Drain 685Ex 685Ex 685Ex

G691L400Tx6 4.00 Open-Drain 685Dx 685Dx 685Dx

G691L308Tx6 3.08 Open-Drain 685Cx 685Cx 685Cx

G691L293Tx6 2.93 Open-Drain 685Bx 685Bx 685Bx

G691L263Tx6 2.63 Open-Drain 685Ax 685Ax 685Ax

G690H463Tx6 4.63 Push-Pull RESET 684Lx 684Lx 684Lx

G690H438Tx6 4.38 Push-Pull RESET 684Kx 684Kx 684Kx

G690H400Tx6 4.00 Push-Pull RESET 684Jx 684Jx 684Jx

G690H308Tx6 3.08 Push-Pull RESET 684Ix 684Ix 684Ix

G690H293Tx6 2.93 Push-Pull RESET 684Hx 684Hx 684Hx

G690H263Tx6 2.63 Push-Pull RESET 684Gx 684Gx 684Gx

G690L463Tx6 4.63 Push-Pull 684Fx 684Fx 684Fx

G690L438Tx6 4.38 Push-Pull 684Ex 684Ex 684Ex

G690L400Tx6 4.00 Push-Pull 684Dx 684Dx 684Dx

G690L308Tx6 3.08 Push-Pull 684Cx 684Cx 684Cx

G690L293Tx6 2.93 Push-Pull 684Bx 684Bx 684Bx

G690L263Tx6 2.63 Push-Pull 684Ax 684Ax 684Ax

Note: T2: SOT89; T7: SOT23; T9: SC70

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Typical Operating Characteristics

(VCC = full range, TA = -40°C to +105°C, unless otherwise noted. Typical values are at TA = +25°C, VCC = 5V

for 463/438/400 versions, VCC= 3.3V for 308/293 versions, and VCC = 3V for 263 version.)

Supply Current vs.Temperature

(No Load)

-40 -20 0 20 40 60 80

Temperature (°C)

Supply Current (µA)

G69_ _ 463/438/400, Vcc=5V

G69_ _ 308/293/263, Vcc=3.3V

G69_ _ 463/438/400/308/293/263, Vcc=1V

Power-down Reset Delay vs.

Temperature (G69_ _308/293/263)

-40-20 0 20406080

Temperature (°C)

Power-down Reset Delay (us

)

VOD = VTH - VCC

VOD = 10mV

VOD = 20mV

VOD = 100mV

VOD = 200mV 0

100

120

140

-40-200 20406080

Temperature (°C)

Power-Down Reset Delay (us)

VOD = VTH - VCC

VOD = 10mV

VOD = 20mV

= 100mV

Normalized Reset Threshold

vs. Temperature

0.988

0.99

0.992

0.994

0.996

0.998

1.002

-40-20 0 20406080

Temperature (°C)

Normalized Threshold

Power-down Reset Delay vs.

Temperature (G69_ _463/438/400)

Power-up Reset Timeout

vs. Temperature

100

200

300

400

500

600

-40-200 20406080

Temperature (°C)

Power-up Reset Timeout (ms

)

G69_ _ 308/293/263

G69

463/438/400

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Pin Description

PIN NAME FUNCTION

1 GND Ground

(G691L/G690L)

RESET Output remains low while VCC is below the reset threshold, and for at least 140ms after

VCC rises above the reset threshold.

2 RESET

(G690H)

RESET Output remains high while VCC is below the reset threshold, and for at least 140ms after

VCC rises above the reset threshold.

3 VCC Supply Voltage (+5V, +3.3V, +3.0V)

Detailed Description

A microprocessor’s (µP’s) reset input starts the µP in a

known state. The G691L/G690L/G690H assert reset to

prevent code-execution errors during power-up,

power-down, or brownout conditions. They assert a

reset signal whenever the VCC supply voltage declines

below a preset threshold, keeping it asserted for at

least 140ms after VCC has risen above the reset

threshold. The G691L uses an open-drain output, and

the G690L/G690H have a push-pull output stage.

Connect a pull-up resistor on the G691L’s RESET out-

put to any supply between 0 and 5.5V.

Figure 1. Maximum Transient Duration Without

Causing a Reset Pulse vs. Reset Com-

parator Overdrive

Figure2. RESET Valid to VCC = Ground Circuit

Applications Information

Negative-Going VCC Transients

In addition to issuing a reset to the µP during

power-up, power-down, and brownout conditions, the

G691L/G690H/G690L are relatively immune to short-

duration negative-going VCC transients (glitches).

Figure 1 shows typical transient duration vs. reset

comparator overdrive, for which the G691L/G690H/

G690L do not generate a reset pulse. The graph was

generated using a negative-going pulse applied to VCC,

starting 0.5V above the actual reset threshold and

ending below it by the magnitude indicated (reset

comparator overdrive). The graph indicates the maxi-

mum pulse width a negative-going VCC transient can

have without causing a reset pulse. As the magnitude

of the transient increases (goes farther below the reset

threshold), the maximum allowable pulse width de-

creases. Typically, for the G69_ _463 and G69_ _438,

a VCC transient that goes 100mV below the reset

threshold and lasts 7µs or less will not cause a reset

pulse. A 0.1µF bypass capacitor mounted as close as

possible to the VCC pin provides additional transient

immunity.

Ensuring a Valid Reset Output Down to VCC = 0

When VCC falls below 1V, the G690 RESET output

no longer sinks current—it becomes an open circuit.

Therefore, high-impedance CMOS logic inputs con-

nected to RESET can drift to undetermined voltages.

This presents no problem in most applications since

most µP and other circuitry is inoperative with VCC

below 1V. However, in applications where RESET

must be valid down to 0V, adding a pull-down resistor

to RESET causes any stray leakage currents to flow

to ground, holding RESET low (Figure 2). R1’s value

is not critical; 100kΩ is large enough not to load

RESET and small enough to pull RESET to ground.

A 100kΩ pull-up resistor to VCC is also recommended

for the G691L if RESET is required to remain valid

for VCC < 1V.

VCC

RESET

GND

G690

100k

VCC

RESET

GND

G690

100k

100

200

300

400

500

600

1 10 100 1000

Reset Comparator Overdrive, VTH- VCC (mV)

Maximum Transient Duration(us

)

G69_ _ 308/293/263

G69_ _ 463/438/400

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Figure 3. Interfacing to µPs with Bidirectional Reset

I/O

Figure 4. G691L Open-Drain RESET Output Allows

Use with Multiple Supplies

Interfacing to µPs with Bidirectional Reset Pins

Since the RESET output on the G691L is open drain,

this device interfaces easily with µPs that have bidi-

rectional reset pins, such as the Motorola 68HC11.

Connecting the µP supervisor’s RESET output di-

rectly to the microcontroller’s (µC’s) RESET pin with

a single pull-up resistor allows either device to assert

reset (Figure 3).

G691L Open-Drain RESET Output Allows Use with

Multiple Supplies

Generally, the pull-up connected to the G691L will

connect to the supply voltage that is being monitored

at the IC’s VCC pin. However, some systems may use

the open-drain output to level-shift from the monitored

supply to reset circuitry powered by some other supply

(Figure 4). Note that as the G691L’s VCC decreases

below 1V, so does the IC’s ability to sink current at

RESET . Also, with any pull-up, RESET will be pulled

high as VCC decays toward 0. The voltage where this

occurs depends on the pull-up resistor value and the

voltage to which it is connected.

Benefits of Highly Accurate Reset Threshold

Most µP supervisor ICs have reset threshold voltages

between 5% and 10% below the value of nominal

supply voltages. This ensures a reset will not occur

within 5% of the nominal supply, but will occur when

the supply is 10% below nominal.

When using ICs rated at only the nominal supply ±5%,

this leaves a zone of uncertainty where the supply is

between 5% and 10% low, and where the reset may or

may not be asserted.

The G69_ _463/G69_ _308 use highly accurate circuitry

to ensure that reset is asserted close to the 5% limit,

and long before the supply has declined to 10% below

nominal.

RESET

INPUT

GND

µP

VCC

RESET

GND

G691

VCC

MOTOROLA

68HCXX

RPULL-UP

RESET

INPUT

GND

µP

VCC

RESET

GND

G691

VCC

MOTOROLA

68HCXX

RPULL-UP

RESET

INPUT

GND

5V SYSTEM

VCC

RESET

GND

G691

VCC

RPULL-UP

+3.3V

+5.0V

RESET

INPUT

GND

5V SYSTEM

VCC

RESET

GND

G691

VCC

RPULL-UP

+3.3V

+5.0V

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

Package Information

SOT- 89 (T2) Package

DIMENSIONS IN MILLIMETERS DIMENSIONS IN INCHES

SYMBOLS MIN NOM MAX MIN NOM MAX

A 1.40 1.50 1.60 0.055 0.059 0.063

A1 0.80 1.04 ----- 0.031 0.041 -----

b 0.36 0.42 0.48 0.014 0.016 0.048

b1 0.41 0.47 0.53 0.016 0.018 0.020

C 038 0.40 0.43 0.014 0.015 0.017

D 4.40 4.50 4.60 0.173 0.177 0.181

D1 1.40 1.60 1.75 0.055 0.062 0.069

HE ----- ----- 4.25 ----- ----- 0.167

E 2.40 2.50 2.60 0.094 0.098 0.102

e 2.90 3.00 3.10 0.114 0.118 0.122

POLISH

MATTE FINISH

POLISH

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

SOT 23 (T7) Package

Note:

1.Package body sizes exclude mold flash protrusions or gate burrs

2.Tolerance ±0.1000 mm (4mil) unless otherwise specified

3.Coplanarity: 0.1000mm

4.Dimension L is measured in gage plane

DIMENSIONS IN MILLIMETERS

SYMBOLS MIN NOM MAX

A 1.00 1.10 1.30

A1 0.00 ----- 0.10

A2 0.70 0.80 0.90

b 0.35 0.40 0.50

C 0.10 0.15 0.25

D 2.70 2.90 3.10

E 1.40 1.60 1.80

e ----- 1.90(TYP) -----

H 2.60 2.80 3.00

L 0.37 ------ -----

θ1 1º 5º 9º

θ1

Ver: 1.3

Oct 31, 2002

TEL: 886-3-5788833

http://www.gmt.com.tw

G690/G691

Global Mixed-mode Technology Inc.

SC70 (T9) Package

Note:

1. All dimensions are in millimeters

2. Dimensions are inclusive of plating of plating

3. Dimensions are exclusive of mold flash & metal burr

4. All specifications comply to EIAJ SC70

5. Coplanarity 4 Mils. Max.

DIMENSION IN MILIMETERS DIMENSION IN INCHS

SYMBOL MIN. MAX. MIN. MAX.

A 0.90 1.20 0.035 0.047

A1 0.05 0.15 0.002 0.006

A2 0.85 1.05 0.033 0.041

b 0.20 0.40 0.008 0.016

C 0.10 0.15 0.004 0.006

D 1.90 2.10 0.075 0.083

E 1.15 1.35 0.045 0.053

E1 2.00 2.20 0.0787 0.0866

e 0.65 BSC. 0.0256 BSC.

e1 1.30 BSC. 0.0512 BSC.

L 0.425 REF. 0.0167 REF.

Package Orientation

GMT Inc. does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and GMT Inc. reserves the right at any time without notice to change said circuitry and specifications.

E1 E

Feed Direction

SOT 89 Package Orientation

Feed Direction

SOT 89 Package Orientation

Feed Direction

SOT23, SC70 Package Orientation

Feed Direction

SOT23, SC70 Package Orientation