MFA350PS24 - XP POWER - Datasheet.Live

AC-DC

Specification

350/420 Watts

•U-Channel, Cover Fan & Hotswap Formats

•Power Density up to 12.8 W/in3

•Power Fail, DC OK & Active Current Share

•5 V Standby Outputs

•12 V Fan Supply Outputs

•Screw Terminals Available

•3 Year Warranty

MFA Series

Input

Input Voltage • 85-264 VAC

(derate output power 10% below 90 VAC)

Input Frequency • 47-63 Hz

Input Current • Typically 3.6 A at 115 VAC &

1.8 A at 230 VAC

Inrush Current • <60 A max at 230 VAC cold start at 25 °C

Power Factor • >0.9

Earth Leakage Current • Typically 1 mA at 230 VAC/50 Hz,

0.5 mA at 115 VAC/60 Hz

Input Protection • T6.3 A/250 V fuse in line

Output

Output Voltage • See tables

Output Voltage Trim • ±10%

Initial Set Accuracy • V1 ±1%, V2 ±5%, V3 ±3%

Minimum Load • No minimum load required

Start Up Delay • 2 s maximum, typically 1 s

Hold Up Time • 16 ms minimum at 90 VAC full load

Drift • ±0.2% after 20 min warm-up

Line Regulation • V1 ±0.5%, V2 ±3.0%, V3 ±0.5%

Load Regulation • V1 ±1.0%, V2 ±5.0%, V3 ±1.0%,

0-100% load V1 & V3, 10-100% load V2

Over/Undershoot • <1% maximum

Transient Response • <4% max deviation,with 50-75-50% load

step. Recovery to within 1% <500 µs

Ripple & Noise • V1 & V3: 1%, V2: 2% pk-pk,

20 MHz bandwidth

Overvoltage Protection • 115-140% Vnom (on V1 only)

Overtemperature • Thermal sensor under PCB shuts unit

Protection down typically >+75 °C, restarts after

cooling

Overload Protection • 110-140%, I nom V1

Short Circuit Protection • Continuous trip and restart (hiccup mode)

Temperature • 0.05%/ºC

Coefficient

Remote Sense • Compensates for 0.5 V total voltage drop

Remote On/Off • Short circuit or TTL Low turns PSU off, can

also be configured as enable

Current Share • Up to 3 supplies can be connected in

parallel, derate total output current to 90%

xppower.com

General

Efficiency • Typically 86%

Isolation • 3000 VAC Input to Output

1500 VAC Input to Ground

100 VDC Output to Ground

Switching Frequency • PFC 62 kHz typical,

Main converter 157 kHz, typical

Power Density • 11.1 W/In3 (MFA350), 12.8 W/In3 (MFA420)

Signals • Power Fail - open collector, transistor off

for AC good, ≥5 ms warning of loss of

output. DC OK - open collector, transistor

off for DC good

MTBF • 460 kHrs to MIL-HDBK-217F, notice 2,

at +25 °C, GB, typical

Environmental

Operating Temperature • Forced cooled: -10 °C to +70 °C, derate

linearly from +50 °C at 2.5%/°C to +70 °C

Cooling • >13 CFM forced airflow required for U

Channel Versions, ‘-H’, ‘-TF’ & ‘-EF’

versions have integral fan

Operating Humidity • 5-95% RH

Storage Temperature • -20 °C to +85 °C

Operating Altitude • 3000 m

Shock • 30 g pk, half sine, 6 axes

Vibration • Single axis 10-500 Hz at 2 g x 10 sweeps

EMC & Safety

Emissions • EN55022, class B conducted,

class A radiated

Harmonic Currents • EN61000-3-2 class A

EN61000-3-2 class C for loads ≥20%

Voltage Flicker • EN61000-3-3

Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A

EFT/Burst • EN61000-4-4, level 3 Perf Criteria A

Surge • EN61000-4-5, installation class 3

Perf Criteria A

Conducted Immunity • EN61000-4-6, 10 V rms Perf Criteria A

Dips & Interruptions • EN61000-4-11, 30% 10 ms, 60% 100 ms,

100% 5000 ms, Perf Criteria A, B, B

Safety Approvals • CB Report, IEC60950-1,

CSA22.2 No. 60950-1-05,

UL60950-1, TUV EN60950-1/A11

AC-DC

MFA350/420

Models and Ratings

Output Voltage V1 Output Current V1 Fan Output V2 (2) Standby Supply V3 Output Power 13 CFM Airflow Model Number(1)

12 VDC 29.0 A 12 V/1 A 5 V/0.3 A 361 W MFA350PS12

24 VDC 14.5 A 12 V/1 A 5 V/0.3 A 361 W MFA350PS24

48 VDC 7

.3 A 12 V/1 A 5 V/0.3 A 364 W MFA350PS48

12 VDC 35.0 A 12 V/1 A 5 V/0.3 A 434 W MFA420PS12

24 VDC 17.5 A 12 V/1 A 5 V/0.3 A 434 W MFA420PS24

48 VDC 8.8 A 12 V/1 A 5 V/0.3 A 436 W MFA420PS48

Mechanical Details

Notes

1. Units supplied with AMP/TE connections for J1 & J2 as standard. Add suffix ‘-S’ to model number to replace with screw terminals. Add suffix ‘-TF’ for covered

version with top fan and suffix ‘-EF’ for covered version with end fan. Example:- MFA420PS12-STF, 12 V unit fitted with screw terminals and top fan.

2. Not available for -TF & -EF versions.

3.20

(81.3)

1.50

(38.1)

3.20

(81.3)

AIRFLOW 2 x 2.00

(50.8)

2 x 0.60

(15.3)

6.80 (172.7)

AC Input

Interface Conn 2 x

0.60 (15.2)

2 x 1.50

(38.1)2 x 0.75

(19.1)

2 x

0.60 (15.2)

6.80 (172.7)

2 x 5.80 (147.3)

Logic Connector

Voltage Adjust

DC output interface

connector

V1(+)

V1(-)

8 X M3-0.5 Mounting Thread

0.236 (6.0) Max Screw Penetration

Typ on all sides of power supply

Max Torque 4.0 - 5.0 in-lb

(0.045 -0.057 kg-m)

BR1

2E1

JP1 12

D35

JP1 (Enable)

Fan Connector V2

C63

Screw Terminal Option Available

Add Suffix -S to Model Number

Max Torque 1.73 in-lb (0.02 kg-m)

0.80

(2.02)

0.6 (15.2) 5.8 (147.3)

0.663

(16.8)

2.0

(50.8)

ACL

GND

3J1

3.326

(84.5)

3.326

(84.5)

2.0

(50.79)

2.0

(50.79)

AC Input

Interface Conn 6.800 (172.72)

V1(-)

V1(+)

Logic

Connector

Voltage

Adjust

Output

Interface

Connector

4 x M3-0.5 Mounting Thread, 0.236 (6.0) Max Screw

Penetration, Bottom Side of Power Supply,

Max Torque 4.0 - 5.0 in-lb (0.045 - 0.057 kg-m)

5 x M3-0.5 Mounting Thread

0.236 (6.0) Max Screw Penetration

Bottom Side of Power Supply

Max Torque 4.0 - 5.0 in-lb (0.045 -0.057 kg-m)

8.280 (210.31)

0.80

(2.03)

0.60

(15.2)

0.663

(16.84)

3.326

(84.48)

2.0

(50.80)

1.375

(34.92)

3.326

(84.47)

1.750

(44.45)

AC Input

Interface Conn

GND

1.750

(44.45)

8.200

(208.28)

6.80

(172.7)

V1(-)

V1(+)

0.400

(10.16)

5.800 (147.32)

1.750

(44.45)

7.200 (182.88)

8.200 (208.28)

Output Interface Connector

Voltage Adjust

Logic Connector

ACL

AIRFLOW

U Channel

Top Fan (Suffix TF)

PIN CONNECTIONS AC INPUT

J1 AMP/TE CONN = 640445-5

1 GND

3 Neutral

5 Line

PIN CONNECTIONS DC OUTPUT

J2 AMP/TE CONN = 1-640445-0

PIN FUNCTION PIN FUNCTION

1 +V1 6 -V1

2 +V1 7 -V1

3 +V1 8 -V1

4 +V1 9 -V1

5 +V1 10 -V1

Mating Parts: AMP/TE CONN = 1-640250-0

Contact 350980-1,

Option ‘-S’ screw terminals

2 x Phoenix Contact: MKDS 1/5-3.81 or similar

accepts 26-16 AWG wire

Max Torque 1.73 in-lb (0.02 kg-m)

Mating Parts: AMP/TE CONN Housing = 640250-5

Contact 350980-1,

Option ‘-S’ screw terminals

Phoenix Contact: MKDS 1/5-3.81 or similar

accepts 26-16 AWG wire (contacts 2 & 4 removed)

Max Torque 1.73 in-lb (0.02 kg-m)

PIN CONNECTIONS LOGIC CONNECTOR

J3 JST B10B-PHDSS (LF) (SN)

PIN FUNCTION PIN FUNCTION

1 AC OK 6 +Sense

2ROF

(Inhibit/Enable) 7 -Sense

3 Current Share 8 Not Used

4 DC OK 9 5 V Standby V3

5 Not used 10 5 V Standby

Return V3

Mating Parts: JST, Housing PHDR-10VS

Contact SPHD-001T-P0.5

Mating Parts: Molex, Housing 22-01-1024

Contact 08-70-0057

PIN CONNECTIONS FAN OUTPUT

J4 Molex 22-04-1021

1 +V2

2 -V2

Notes

1. All dimensions in inches (mm).

2. Tolerance: .xx=±0.02 (±0.50); .xxx=±0.01 (±0.25)

End Fan (Suffix EF)

Weight: 1.7 lb (771 g) approx

Weight: 1.35 lb (612 g) approx

Weight: 1.7 lb (771 g) approx

AC-DC

MFA350/420

Output Voltage V1 Output Current Standby Supply V3 Output Power Model Number

12.0 VDC 29.0 A 5 V/0.3 A 350 W MFA350PS12-H

24.0 VDC 14.5 A 5 V/0.3 A 350 W MFA350PS24-H

48.0 VDC 7

.3 A 5 V/0.3 A 352 W MFA350PS48-H

12.0 VDC 35.0 A 5 V/0.3 A 434 W MFA420PS12-H

24.0 VDC 17.5 A 5 V/0.3 A 434 W MFA420PS24-H

48.0 VDC 8.8 A 5 V/0.3 A 436 W MFA420PS48-H

IEC320 INPUT CONNECTOR

AC INPUT &

DC OUTPUT

HEALTHY LED’S

EJECTOR HANDLE

OUTPUT CONNECTOR

0.125

(3.18)

1.60

(40.6)

GUIDE PIN C/L

0.655

(16.64)

0.385

(9.78)

10.06 (255.52)

10.00 (254.0)

ø0.156 (3.96) EJECTOR PIN

R0.225 (5.71) ROTATION RADIUS

0.225

(5.72)

0.175

(4.44)

CONNECTOR C/L

3.30

(83.8)

MAX

1.636

(41.55)

Pin Connections

PIN CONNECTIONS

INPUT CONNECTOR IEC320

Earth

Live

Neutral

Mating parts: FCI 51762-10401200AA-LF

PIN CON. OUTPUT CON.

FCI 51732-035-LF

A1 +Sense

A2 Not Used

A3 DC OK

B1 -Sense

B2 Not Used

B3 AC OK

C1 Current Share

C2 Not Used

C3 5 V Standby V3

D1 Not Used

D2 ROF (Inhibit/Enable)

D3 5 V Standby Return V3

P1 -V1

P2 -V1

P3 +V1

P4 +V1

PIN CONNECTIONS

OUTPUT CONNECTOR

123

P1 P2 P3 P4

Viewed looking at PSU male partViewed looking at PSU male part

Mechanical Details

Models and Ratings

-H Hotswap

Notes

1. All dimensions in inches (mm).

2. Weight: 2.65 lb (1202 g) approx

3. Tolerance: .xx=±0.02 (±0.50); .xxx=±0.01 (±0.25)

03-Jun-16

AC-DC

MFA350/420

Thermal Considerations (U Channel)

AC OK Collector

Pin 1 or B3

AC OK Emitter

Pin 7 or B1

POWER SUPPLY

Transistor On (<0.8 V): AC NOT OK

Transistor Off (>4.5 V): AC OK

J3 Logic Connector

330R

5 V Standby

Return Pin 10

or D3

5 V Standby

Pin 9 or C3

Max 12 V 20 mA

DC OK Collector

Pin 4 or A3

DC OK Emitter

Pin 7 or B1

POWER SUPPLY

Transistor On (<0.8 V): DC NOT OK

Transistor Off (>4.5 V): DC OK

J3 Logic Connector

330R

5 V Standby

Return Pin 10

or D3

5 V Standby

Pin 9 or C3

Max 12 V 20 mA

POWER SUPPLY

J3 Logic Connector

Pin 7 or B1

Pin 2

or D2

Jumper (JP1) fitted (standard)

Open or TTL high=PSU On

Short circuit or TTL Low=PSU Off

Internal

Vref

JP1

See 2nd page of this datasheet

Mechanical Details for location

Jumper (JP1) removed

Open or TTL high=PSU Off

Short circuit or TTL Low=PSU On

AC OK/Power Fail DC OK Remote On/Off (Inhibit/Enable)

MFA Temperature Measurements (Ambient ≤50°C)

Component Max Temperature °C

T3 90 °C

BR1 105 °C

D35 85 °C

L3 90 °C

C8 105 °C

C63 105 °C

Signals

DFA Temperature Measurements (Ambient ≤50°C)

Component Max Temperature °C

L1 90 °C

Q1 105 °C

HS1 85 °C

C25 75 °C

Q2 105 °C

In order to ensure safe operation of the PSU in the end-use equipment, the temperature of the components listed in the table below must not be

exceeded. See mechanical details for component locations. The temperature should be monitored using K type thermocouples placed on the hottest

part of the component (out of any direct air flow). See longform datasheet for further information of service life.