AAAF5051-04 - KINGBRIGHT CORPORATION

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 1 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

5.0mm x 5.0mm FULL-COLOR SURFACE

MOUNT LED LAMP

Part Number: AAAF5051-04

Blue

Reddish-Orange

Green

Features

zChips can be controlled separately.

zSuitable for all SMT assembly and solder process.

zAvailable on tape and reel.

zWhite SMD package, silicone resin.

zPackage: 500pcs / reel.

zMoisture sensitivity level : level 3.

zRoHS compliant.

Descriptions

zThe Blue source color devices are made with InGaN on

Al2O3 substrate Light Emitting Diode.

zThe Reddish-Orange source color devices are made with

AlGaInP on AlN substrate Light Emitting Diode.

zThe Green source color devices are made with InGaN on

Al2O3 substrate Light Emitting Diode.

zElectrostatic discharge and power surge could damage

the LEDs.

zIt is recommended to use a wrist band or anti-

electrostatic glove when handling the LEDs.

zAll devices, equipments and machineries must be

electrically grounded.

Package Dimensions

Notes:

1. All dimensions are in millimeters (inches).

2. Tolerance is ±0.15[±0.006]unless otherwise noted.

3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.

4. The device has a single mounting surface. The device must be mounted according to the specifications.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

DISCHARGE

SENSITIVE

DEVICES

R

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 2 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

Handling Precautions

Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic

significantly reduces thermal stress, it is more susceptible to damage by external mechanical force.

As a result, special handling precautions need to be observed during assembly using silicone encapsulated

LED products. Failure to comply might lead to damage and premature failure of the LED.

1. Handle the component along the side surfaces by using forceps or appropriate tools.

2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry.

3. Do not stack together assembled PCBs containing exposed LEDs. Impact may scratch the silicone lens or

damage the internal circuitry.

4.1. The inner diameter of the SMD pickup nozzle should not exceed the size of the LED to prevent air leaks.

4.2. A pliable material is suggested for the nozzle tip to avoid scratching or damaging the LED surface during pickup.

4.3. The dimensions of the component must be accurately programmed in the pick-and-place machine to insure precise pickup

and avoid damage during production.

5. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of

leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances.

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 3 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

Selection Guide

Notes:

1. Results from mounting on Aluminum Board.

2. 1/10 Duty Cycle, 0.1ms Pulse Width.

Absolute Maximum Ratings at Ta=25°C

Part No. Dice Lens Type

Iv (mcd) [2]

@ 150mA

V

iewing

Angle [1]

Min. Typ. Min. Typ. 2θ1/2

AAAF5051-04

Blue (InGaN)

Water Clear

1000 1500 4.2 6

120°

Reddish-Orange (AlGaInP) 2700 3200 10 12

Green (InGaN) 5000 6300 17 20

Φv (lm) [2]

@ 150mA*

Parameter Symbol Device Value Unit Test Conditions

Power dissipation PD

Blue 0.6

W

IF=150mA

Reddish-Orange 0.45

Green 0.6

Junction temperature TJ

Blue 110

°C IF=150mA

IF=150mA

Reddish-Orange 110

Green 110

Operating Temperature Top

Blue

-40 To +85 °C

IF=150mA

Reddish-Orange

Green

Storage Temperature Tstg

Blue

-40 To +85 °C

IF=150mA

Reddish-Orange

Green

DC Forward Current [1] IF

Blue 150

mA

IF=150mA

Reddish-Orange 150

Green 150

Peak Forward Current [2] IFM

Blue 300

mA

IF=150mA

Reddish-Orange 300

Green 300

Thermal resistance Rth j-a

Blue 220

°C/W IF=150mA

IF=150mA

Reddish-Orange 270

Green 200

Thermal resistance Rth j-s

Blue 25

°C/W IF=150mA

IF=150mA

Reddish-Orange 40

Green 33

Reverse Current IR

Blue 10

VR=5V

Reddish-Orange 10

Green 10

uA

Notes:

1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.

2. Luminous intensity/ luminous Flux: +/-15%.*LEDs are binned according to their luminous flux.

3. Luminous intensity/ luminous Flux value is traceable to the CIE127-2007 compliant national standards.

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 4 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

Electrical / Optical Characteristics at Ta=25°C

Notes:

1.Wavelength: +/-1nm.

2.Forward Voltage: +/-0.2V.

3.Wavelength value is traceable to the CIE127-2007 compliant national standards.

4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or

premature failure.

Parameter Symbol Device

Value

Unit

Min. Typ. Max.

Wavelength at peak emission

IF=150mA

λpeak

Blue 452

nm

Wavelength at peak emission

IF=150mA Reddish-Orange 635

Wavelength at peak emission

IF=150mA Green 515

Dominant Wavelength

IF=150mA

λdom [1]

Blue 460

nm

Dominant Wavelength

IF=150mA Reddish-Orange 624

Dominant Wavelength

IF=150mA Green 525

Spectral Line Half-width

IF=150mA

Δλ1/2

Blue 25

nm

Spectral Line Half-width

IF=150mA Reddish-Orange 20

Spectral Line Half-width

IF=150mA Green 30

Forward Voltage IF=150mA

VF [2]

Blue 3.0 3.5 4.0

V Forward Voltage IF=150mA Reddish-Orange 2.0 2.5 3.0

Forward Voltage IF=150mA Green 3.0 3.5 4.0

Reverse Voltage VR

Blue 5

V Reddish-Orange 5

Green 5

Temperature coefficient of λpeak

IF=150mA, -10 °C≤ T≤100 °C

TC λpeak

Blue 0.12

nm/°C

Temperature coefficient of λpeak

IF=150mA, -10 °C≤ T≤100 °C Reddish-Orange 0.09

Temperature coefficient of λpeak

IF=150mA, -10 °C≤ T≤100 °C Green 0.13

Temperature coefficient of λdom

IF=150mA, -10 °C≤ T≤100 °C

TC λdom

Blue 0.1

nm/°C

Temperature coefficient of λdom

IF=150mA, -10 °C≤ T≤100 °C Reddish-Orange 0.03

Temperature coefficient of λdom

IF=150mA, -10 °C≤ T≤100 °C Green 0.11

Temperature coefficient of VF

IF=150mA, -10 °C≤ T≤100 °C

TCV

Blue -2.3

mV/°C

Temperature coefficient of VF

IF=150mA, -10 °C≤ T≤100 °C Reddish-Orange -2.7

Temperature coefficient of VF

IF=150mA, -10 °C≤ T≤100 °C Green -3.9

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 5 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

AAAF5051-04

Blue

GREEN

BLUE REDDISH-ORANGE

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 6 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

Reddish-orange

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 7 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

Green

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 8 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

AAAF5051-04

Reflow soldering is recommended and the soldering profile is shown below.

Other soldering methods are not recommended as they might cause damage to the product.

Reel Dimension

Recommended Soldering Pattern

(Units : mm; Tolerance: ± 0.1)

Tape Specifications

(Units : mm)

SPEC NO: DSAM7047 REV NO: V.4B DATE: SEP/16/2014 PAGE: 9 OF 9

APPROVED: WYNEC CHECKED: Allen Liu DRAWN: L.Q.Xie ERP : 1201008410

PACKING & LABEL SPECIFICATIONS AAAF5051-04

Terms and conditions for the usage of this document

1.The information included in this document reflects representative usage scenarios and is intended

for technical reference only.

2.The part number, type, and specifications mentioned in this document are subject to future change

and improvement without notice. Before production usage customer should refer to the latest

datasheet for the updated specifications.

3.When using the products referenced in this document, please make sure the product is being

operated within the environmental and electrical limits specified in the datasheet. If customer usage

exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.

4.The information in this document applies to typical usage in consumer electronics applications.

If customer's application has special reliability requirements or have life-threatening liabilities,

such as automotive or medical usage, please consult with Kingbright representative for further

assistance.

5.The contents and information of this document may not be reproduced or re-transmitted without

permission by Kingbright.

6.All design applications should refer to Kingbright application notes available at

http://www.KingbrightUSA.com/ApplicationNotes