Intel® I/O Expansion
Modules
Hardware Specification
Intel order number: D44901-008
Revision 1.2
September 2010
Enterprise Platforms and Services Division
Revision History Intel® I/O Expansion Modules
Revision History
Date Revision
Number
Modifications
March 2009 1.0 Initial Release.
November 2009 1.1 Added AXXIBQDRIOMOD.
September 2010 1.2 Added new SAS modules and IB QDR modules.
Disclaimers
Information in this document is provided in connection with Intel® products. No license, express
or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document. Except as provided in Intel's Terms and Conditions of Sale for such products, Intel
assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to
sale and/or use of Intel products including liability or warranties relating to fitness for a particular
purpose, merchantability, or infringement of any patent, copyright or other intellectual property
right. Intel products are not intended for use in medical, life saving, or life sustaining
applications. Intel may make changes to specifications and product descriptions at any time,
without notice.
Designers must not rely on the absence or characteristics of any features or instructions marked
"reserved" or "undefined." Intel reserves these for future definition and shall have no
responsibility whatsoever for conflicts or incompatibilities arising from future changes to them.
This document contains information on products in the design phase of development. Do not
finalize a design with this information. Revised information will be published when the product
is available. Verify with your local sales office that you have the latest datasheet before
finalizing a design.
The Intel® I/O Expansion Modules may contain design defects or errors known as errata which
may cause the product to deviate from published specifications. Current characterized errata
are available on request.
Intel Corporation server baseboards contain a number of high-density VLSI and power delivery
components that need adequate airflow to cool. Intel’s own chassis are designed and tested to
meet the intended thermal requirements of these components when the fully integrated system
is used together. It is the responsibility of the system integrator that chooses not to use Intel
developed server building blocks to consult vendor datasheets and operating parameters to
determine the amount of air flow required for their specific application and environmental
conditions. Intel Corporation cannot be held responsible if components fail or the server board
does not operate correctly when used outside any of their published operating or non-operating
limits.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation.
*Other brands and names may be claimed as the property of others.
Copyright © Intel Corporation 2010.
Revision 1.2
Intel order number: D44901-008
ii
Intel® I/O Expansion Modules Table of Contents
Table of Contents
1.Introduction .......................................................................................................................... 1
2.Dual Port GbE I/O Module (AXXGBIOMOD) ....................................................................... 3
2.1Feature Set .............................................................................................................. 3
2.2Functional Block Diagram ........................................................................................ 4
2.3Mechanical Dimensions ........................................................................................... 5
2.4Intel® 82571EB Gb Ethernet Controller .................................................................... 6
2.5EEPROM ................................................................................................................. 7
2.6PCI Express* x4 Connector ..................................................................................... 7
2.7Ethernet Magjack ..................................................................................................... 7
3.External 4 Port SAS I/O Module (AXXSASIOMOD) ............................................................ 8
3.1Feature Set .............................................................................................................. 8
3.2Functional Block Diagram ........................................................................................ 9
3.3Mechanical Dimensions ......................................................................................... 10
3.4LSI* SAS1064E 3.0 Gbit/s Serial Attached SCSI Controller .................................. 11
3.4.1Features of the LSI* SAS1064E ............................................................................ 13
3.5External Flash Memory .......................................................................................... 13
3.6PCI Express* x4 Connector ................................................................................... 13
3.7External 4 SAS Connector .................................................................................... 13
4.InfiniBand* (SDR) Module (AXXIBIOMOD) ....................................................................... 15
4.1Feature Set ............................................................................................................ 15
4.2Functional Block Diagram ...................................................................................... 16
4.3Mechanical Dimensions ......................................................................................... 17
4.4LED Functionality ................................................................................................... 18
4.5PCI Express* x4 Connector ................................................................................... 19
4.6External Connector ................................................................................................ 19
5.Internal 4-port LSI 1064e SAS I/O Module (AXX4SASMOD) ........................................... 20
5.1Major Component Diagram .................................................................................... 20
5.2Functional Block Diagram ...................................................................................... 21
5.3Feature Set ............................................................................................................ 21
5.4Mechanical Drawings ............................................................................................. 22
6.Integrated RAID Module SROMBSASMR (AXXROMBSASMR) ....................................... 24
Revision 1.2
Intel order number: D44901-008
iii
Table of Contents Intel® I/O Expansion Modules
6.1Product Overview .................................................................................................. 24
6.2Hardware Architectural Features ........................................................................... 24
6.3Block Diagram ....................................................................................................... 25
6.4Controller Layout ................................................................................................... 25
6.4.1Mechanical Drawings ............................................................................................. 26
6.4.2Jumpers and Connectors ....................................................................................... 27
7.Quad Port GbE I/O Module (AXX4GBIOMOD2) ................................................................ 28
7.1Feature Set ............................................................................................................ 28
7.2Functional Block Diagram ...................................................................................... 29
7.3Mechanical Drawings ............................................................................................. 30
7.4Intel® 82576 1 Gb Ethernet Controller ................................................................... 31
7.5EEPROM ............................................................................................................... 31
7.6PCI Express* x8 Connector ................................................................................... 32
7.7Gbit Ethernet Connector ........................................................................................ 32
8.Dual Port 10GbE I/O Module (AXX10GBIOMOD) ............................................................. 33
8.1Feature Set ............................................................................................................ 33
8.2Functional Block Diagram ...................................................................................... 34
8.3Mechanical Drawings ............................................................................................. 35
8.4Intel® 82598 10 Gb Ethernet Controller ................................................................. 36
8.5EEPROM ............................................................................................................... 37
8.6PCI Express* x8 Connector ................................................................................... 37
8.7CX4 Ethernet Connector ........................................................................................ 37
9.InfiniBand* (QDR) I/O Modules .......................................................................................... 38
9.1Support Matrix ....................................................................................................... 38
9.2Feature List ............................................................................................................ 39
9.3Functional Block Diagram ...................................................................................... 39
9.4LED Functionality ................................................................................................... 40
9.5PCI Express* x4 Connector ................................................................................... 40
9.6External Connector ................................................................................................ 40
10.Intel® Integrated RAID Module RMS2MH080 .................................................................... 41
10.1Technical Specifications ........................................................................................ 41
11.Integrated RAID Module RMS2AF040 & RMS2AF080 ...................................................... 44
11.1Technical Specifications ........................................................................................ 45
11.2Intel® Integrated RAID Module RMS2AF0x0 Characteristics ................................. 46
12.Integrated RAID Module RMS2LL040 & RMS2LL080 ...................................................... 48
Revision 1.2
Intel order number: D44901-008
iv
Intel® I/O Expansion Modules Table of Contents
12.1Technical Specifications ........................................................................................ 49
12.2Intel® Integrated RAID Module RMS2LL0x0 Characteristics ................................. 50
Revision 1.2
Intel order number: D44901-008
v
List of Figures Intel® I/O Expansion Modules
List of Figures
Figure 1. Dual Port GbE I/O Module ............................................................................................. 3
Figure 2. Dual Gb Ethernet I/O Module Block Diagram ................................................................ 4
Figure 3. Dual Gb Ethernet I/O Module Dimensions; Top and Side Views ................................... 5
Figure 4. Dual Gb Ethernet I/O Module Dimensions; Bottom View............................................... 6
Figure 5. External 4 Port SAS I/O Module (AXXSASIOMOD) ...................................................... 8
Figure 6. External SAS I/O Module Block Diagram ...................................................................... 9
Figure 7. SAS I/O Module Dimensions; Top and Side Views ..................................................... 10
Figure 8. SAS I/O Module Dimensions; Bottom View ................................................................. 11
Figure 9. LSI* SAS1064E Block Diagram ................................................................................... 12
Figure 10. Single InfiniBand* (SDR) Module (AXXIBIOMOD) ..................................................... 15
Figure 11. InfiniBand* I/O Module Block Diagram ...................................................................... 16
Figure 12. InfiniBand* I/O Module Dimensions; Top and Side Views ......................................... 17
Figure 13. InfiniBand* I/O Module Dimensions; Bottom View ..................................................... 18
Figure 14. Intel® SAS Entry RAID Module AXX4SASMOD Component and Connector ............. 20
Figure 15. Intel® SAS Entry RAID Module AXX4SASMOD Functional Block Diagram ............... 21
Figure 16. AXX4SASMOD Mechanical Dimensions (Top View) ................................................. 22
Figure 17. AXX4SASMOD Mechanical Dimensions (Bottom View) ............................................ 23
Figure 18. Hardware Block Diagram ........................................................................................... 25
Figure 19. Intel® Integrated RAID Controller SROMBSASMR Physical Layout .......................... 25
Figure 20. Primary Side .............................................................................................................. 26
Figure 21. Secondary Side ......................................................................................................... 26
Figure 22. Jumpers and Connectors ........................................................................................... 27
Figure 23. Quad-Port GbE I/O Module (AXX4GBIOMOD2) ........................................................ 28
Figure 24. Quad-port Gigabit Ethernet I/O Module Block Diagram ............................................. 29
Figure 25. Quad-Port GbE I/O Module Mechanical Drawing ...................................................... 30
Figure 26. Quad-Port GbE I/O Module Mechanical Drawing ...................................................... 31
Figure 27. Dual Port 10GbE I/O Module ..................................................................................... 33
Figure 28. Dual 10 Gb Ethernet I/O Module Block Diagram ....................................................... 34
Figure 29. Dual 10 Gb Ethernet I/O Module Dimensions: Top and Side Views .......................... 35
Figure 30. Dual 10 Gb Ethernet I/O Module Dimensions: Bottom View...................................... 36
Figure 31. AXXIBQDRIOMO ....................................................................................................... 38
Figure 32. AXXIBQDRSR169X ................................................................................................... 38
Revision 1.2
Intel order number: D44901-008
vi
Intel® I/O Expansion Modules List of Figures
Figure 33. AXXIBQDRIOMV ....................................................................................................... 38
Figure 34. InfiniBand* (QDR) I/O Module Block Diagram ........................................................... 39
Figure 35. RMS2MH080 Card Layout ......................................................................................... 42
Figure 36. RMS2MH080 Block Diagram ..................................................................................... 43
Figure 37. RMS2AF080 Card Layout .......................................................................................... 46
Figure 38. RMS2AF040 Hardware Block Diagram ..................................................................... 47
Figure 39. RMS2AF080 Hardware Block Diagram ..................................................................... 47
Figure 40. Intel® Integrated RAID Module RMS2LL0x0 Characteristics ..................................... 50
Figure 41. RMS2LL040 Hardware Block Diagram ...................................................................... 51
Figure 42. RMS2LL080 Hardware Block Diagram ...................................................................... 51
Revision 1.2
Intel order number: D44901-008
vii
List of Tables Intel® I/O Expansion Modules
List of Tables
Table 1. I/O Module Support Matrix .............................................................................................. 1
Table 2. 50-pin I/O Module Connector Pin-Out ............................................................................. 2
Table 3. External SAS x4 Connector Pin-Out ............................................................................. 14
Table 4. AXX4SASMOD Storage Mode ...................................................................................... 22
Table 5. Hardware Architectural Features .................................................................................. 24
Table 6. Support Matrix Data ...................................................................................................... 38
Table 7. RMS2MH080 Specifications ......................................................................................... 41
Table 8. RMS2AF0#0 Specifications .......................................................................................... 45
Table 9. RMS2LL0#0 Specifications ........................................................................................... 49
Revision 1.2
Intel order number: D44901-008
viii
Intel® I/O Expansion Modules List of Tables
Revision 1.2
Intel order number: D44901-008
ix
< This page intentionally left blank. >
Intel® I/O Expansion Modules Introduction
1. Introduction
The Intel® Server Boards support a variety of Intel® I/O Expansion Module options using x4 PCI
Express* Gen2 Mezzanine connectors on the server board. Each mezzanine connector is a 50-
pin, surface mount, 0.8 mm pitch header.
The Intel® I/O Expansion Modules are designed to fit Intel® Server Boards. The table below
shows the support matrix for the Intel® I/O Expansion Modules.
Table 1. I/O Module Support Matrix
Intel® I/O Expansion Module
Product
Code
S5000PAL
S5400SF
S5520UR
S5500WB
S5520HC
S5520SC
S5500BC
SR1680MV
S3420GPRX
Single Connector
Dual-port Intel 82571EB GbE AXXGBIOMOD 3 3 3 3 2 2 2 2 3
External 4-port SAS (LSI1064e) AXXSASIOMOD 3 3 3 3 2 2 2 2 3
Single-port InfiniBand* (SDR) AXXIBIOMOD 3 3 3 2 2 2 2 2 2
Double Connector
Dual-port Intel 82598EB
10GbE* AXX10GBIOMOD 2 2 3 3 2 2 2 3 2
4-port Intel 82576EB GbE* AXX4GBIOMOD2 2 2 3 3 2 2 2 2 3
Single-port InfiniBand* (QDR) AXXIBQDRIOMOD 2 2 3 2 2 2 2 2 2
Single-port InfiniBand* (QDR) AXXIBQDRSR169X 2 2 2 3 2 2 2 2 2
Single-port InfiniBand* (QDR) AXXIBQDRIOMV 2 2 2 2 2 2 2 3 2
SAS Controllers
4-port Internal SAS
(LSI1064e)* AXX4SASMOD 2 2 3 3 3 3 2 2 3
4-port Internal SAS HW RAID
(LSI1078)* AXXROMBSASMR 2 2 3 3 3 3 2 2 3
8-port 6Gb Integrated RAID
(LSI2108) AXXRMS2MH080 2 2 3 3 2 2 2 2 2
4-port/8-port 6Gb RAID
(LSI2008)
AXXRMS2LL040 /
AXXRMS2LL080 2 2 3 3 3 3 2 2 3
4-port/8-port 6Gb RAID
(LSI2008)
AXXRMS2AF040 /
AXXRMS2AF080 2 2 3 3 3 3 2 2 3
Revision 1.2
Intel order number: D44901-008
1
Introduction Intel® I/O Expansion Modules
Revision 1.2
Intel order number: D44901-008
2
The following table details the pin-out of the I/O module connector.
Table 2. 50-pin I/O Module Connector Pin-Out
Pin Name Pin Name
1 3V3_STBY 2 3V3_STBY
3 PE_RST_G2_PM_N 4 GND
5 GND 6 PE0_DUAL_TX_DP<0>
7 GND 8 PE0_DUAL_TX_DN<0>
9 PE0_DUAL_RX_DP<0> 10 GND
11 PE0_DUAL_RX_DN<0> 12 GND
13 GND 14 PE0_DUAL_TX_DP<1>
15 GND 16 PE0_DUAL_TX_DN<1>
17 PE0_DUAL_RX_DP<1> 18 GND
19 PE0_DUAL_RX_DN<1> 20 GND
21 GND 22 PE0_DUAL_TX_DP<2>
23 GND 24 PE0_DUAL_TX_DN<2>
25 PE0_DUAL_RX_DP<2> 26 GND
27 PE0_DUAL_RX_DN<2> 28 GND
29 GND 30 PE0_DUAL_TX_DP<3>
31 GND 32 PE0_DUAL_TX_DN<3>
33 PE0_DUAL_RX_DP<3> 34 GND
35 PE0_DUAL_RX_DN<3> 36 GND
37 GND 38 CLK_100M_LP_PE_P
39 GND 40 CLK_100M_LP_PE_N
41 PE_WAKE_N 42 GND
43 3V3 44 3V3
45 3V3 46 3V3
47 3V3 48 3V3
49 3V3 50 3V3
Intel® I/O Expansion Modules Dual Port GbE I/O Module (AXXGBIOMOD)
2. Dual Port GbE I/O Module (AXXGBIOMOD)
The dual Gigabit (Gb) I/O module provides two additional 10/100/1000Mbit external
connections. This section provides a high-level description of the implementation of this I/O
module.
Figure 1. Dual Port GbE I/O Module
2.1 Feature Set
The dual Gb Ethernet I/O module supports the following feature set:
Intel® 82571EB Gb Ethernet Controller
Dual port
Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-T
Can be implemented in a very small area
Onboard System Management Bus (SMB) ports
PCI Express* x4 interface
Supports two external Gb Ethernet ports
Revision 1.2
Intel order number: D44901-008
3
Dual Port GbE I/O Module (AXXGBIOMOD) Intel® I/O Expansion Modules
2.2 Functional Block Diagram
Intel
®
82571EB
50-Pin Connector
ESB2-E
Server Board
PCIe* x4
Ethernet
PCIe* x4
EEPROM
Ethernet
Figure 2. Dual Gb Ethernet I/O Module Block Diagram
Revision 1.2
Intel order number: D44901-008
4
Intel® I/O Expansion Modules Dual Port GbE I/O Module (AXXGBIOMOD)
2.3 Mechanical Dimensions
Figure 3. Dual Gb Ethernet I/O Module Dimensions; Top and Side Views
Revision 1.2
Intel order number: D44901-008
5
Dual Port GbE I/O Module (AXXGBIOMOD) Intel® I/O Expansion Modules
Figure 4. Dual Gb Ethernet I/O Module Dimensions; Bottom View
2.4 Intel® 82571EB Gb Ethernet Controller
The Intel® 82571EB Gb Ethernet Controller is a single, compact component with two fully
integrated Gb Ethernet Media Access Control (MAC) and physical layer (PHY) ports. This
device uses the PCI Express* architecture (Rev. 1.0a) and also enables a dual-port Gb Ethernet
implementation. The Intel® 82571EB Gb Ethernet Controller provides two IEEE 802.3 Ethernet
interfaces for 1000BASE-T, 100BASE-TX, and 10BASE-T applications. Both ports also
integrate a Serializer-Deserializer (SerDes) to support 1000BASE-SX or 1000BASE-LX (optical
fiber) and Gb backplane applications. In addition to managing MAC and PHY Ethernet layer
functions, the controller manages PCI Express* packet traffic across its transaction, link, and
physical/logical layers.
The Intel® 82571EB Gb Ethernet Controller for PCI Express* is designed for high-performance
and low memory latency. The device is optimized to connect to a system Memory Control Hub
(MCH) using up to four PCI Express* lanes. Wide internal data paths eliminate performance
bottlenecks by efficiently handling large address and data words. Combining parallel and
pipelined logic architecture optimized for Gb Ethernet and for independent transmit and receive
queues, the controller efficiently handles packets with minimum latency. The controller includes
advanced interrupt-handling features and uses efficient ring-buffer descriptor data structures
with up to 64 packet descriptors cached on chip. A large 48 Kbyte per port on-chip packet buffer
maintains superior performance. Using hardware acceleration, the controller offloads tasks from
Revision 1.2
Intel order number: D44901-008
6
Intel® I/O Expansion Modules Dual Port GbE I/O Module (AXXGBIOMOD)
Revision 1.2
Intel order number: D44901-008
7
the host, such as checksum calculations for Transmission Control Protocol (TCP), User
Datagram Protocol (UDP), and Internet Protocol (IP); header and data splitting; and TCP
segmentation.
2.5 EEPROM
The Dual Gb Ethernet I/O module provides a SPI serial EEPROM to store configuration and
informational data. This includes pre-boot configuration data, MAC addresses, and serial
numbers for the 82571EB.
2.6 PCI Express* x4 Connector
The Dual Gb Ethernet I/O module contains one 50-pin connector.
2.7 Ethernet Magjack
The Dual Gb Ethernet I/O module contains two Ethernet Magjacks which are compatible with
10/100/1000 Mbps Ethernet connection.
External 4 Port SAS I/O Module (AXXSASIOMOD) Intel® I/O Expansion Modules
3. External 4 Port SAS I/O Module (AXXSASIOMOD)
The SAS I/O module provides the availability to connect up to four external SAS ports to an
Intel® Server Board. This section provides a high-level description of the implementation of this
Intel® I/O Expansion Modules.
Figure 5. External 4 Port SAS I/O Module (AXXSASIOMOD)
3.1 Feature Set
The SAS I/O module supports the following feature set:
LSI* LSISAS1064E SAS/SATA controller
Four-port, 3.0 Gbit/s SAS/SATA controller
Integrated Arm966 microprocessor core
Compliant with Fusion-MPT* architecture
x4 PCI Express*
Provides four external SAS/SATA ports for connecting multiple SAS/SATA devices.
Revision 1.2
Intel order number: D44901-008
8
Intel® I/O Expansion Modules External 4 Port SAS I/O Module (AXXSASIOMOD)
3.2 Functional Block Diagram
LSISAS 1064
50-Pin Connector
ESB2-E PCIe* X4 4 lane SAS
PCIe* X4
External
Flash
SAS Drives
Server Board
Figure 6. External SAS I/O Module Block Diagram
Revision 1.2
Intel order number: D44901-008
9
External 4 Port SAS I/O Module (AXXSASIOMOD) Intel® I/O Expansion Modules
3.3 Mechanical Dimensions
Figure 7. SAS I/O Module Dimensions; Top and Side Views
Revision 1.2
Intel order number: D44901-008
10
Intel® I/O Expansion Modules External 4 Port SAS I/O Module (AXXSASIOMOD)
Figure 8. SAS I/O Module Dimensions; Bottom View
3.4 LSI* SAS1064E 3.0 Gbit/s Serial Attached SCSI Controller
Integrated on the SAS I/O module is an LSI* SAS1064E Serial Attached SCSI (SAS) controller.
The LSISAS1064E is a four-port, 3.0 Gbit/s SAS/SATA controller compliant with the Fusion-
MPT* architecture, and provides a four-lane PCI Express* interface. The point-to-point
interconnect feature of the PCI Express* bus limits the electrical load on links, allowing
increased transmission and reception frequencies. PCI Express* transmission and reception
data rates for each full-duplex interconnect is 2.5 Gbit/s.
Revision 1.2
Intel order number: D44901-008
11
External 4 Port SAS I/O Module (AXXSASIOMOD) Intel® I/O Expansion Modules
4
Figure 9. LSI* SAS1064E Block Diagram
PCI Express* implements a switch-based technology to interconnect a large number of devices.
Communication over the serial interconnect is accomplished using packet-based
communication protocol. Quality of Service (QOS) features provide differentiated transmission
performance for different applications. Hot plug/hot swap support enables “always-on” systems.
Enhanced error handling features, such as end-to-end CRC (ECRC) and Advanced Error
Reporting, make PCI Express suitable for robust, high-end server applications. Hot plug, power
management, error handling, and interrupt signaling are accomplished using packet-based
messaging rather than sideband signals.
Each of the four SAS PHYs on the LSISAS1064E is capable of SAS/SATA link rates of 3.0
Gbit/s and 1.5 Gbit/s. The user can configure ports as wide or narrow. Narrow ports have one
PHY per port. Wide ports have two, three, or four PHYs per port. Each port supports the SSP,
SMP, STP, and SATA protocols.
The SAS interface uses the proven SCSI command set to ensure reliable data transfers, while
providing the connectivity and flexibility of point-to-point serial data transfers. The SAS interface
provides improved performance, simplified cabling, smaller connectors, lower pin count, and
lower power requirements when compared to parallel SCSI. SAS controllers leverage an
electrical and physical connection interface that is compatible with Serial ATA technology.
The LSISAS1064E uses the Fusion-MPT* (Message Passing Technology) architecture, which
features a performance-based message passing protocol that offloads the host CPU by
completely managing all I/Os and minimizes system bus overhead by coalescing interrupts. The
proven Fusion-MPT* architecture requires only thin, easy-to-develop device drivers independent
of the I/O bus. LSI* Logic provides these device drivers.
Revision 1.2
Intel order number: D44901-008
12
Intel® I/O Expansion Modules External 4 Port SAS I/O Module (AXXSASIOMOD)
3.4.1 Features of the LSI* SAS1064E
SAS and SSP features:
Each PHY supports 3.0 Gbit/s and 1.5 Gbit/s SAS data transfers
Provides a serial, point-to-point, enterprise-level storage interface
Supports wide transfers consisting of 2, 3, or 4 PHYs
Supports narrow ports consisting of a single PHY
Transfers data using SCSI information units
Compatible with SATA target devices
SATA and STP Features:
Supports 3.0 Gbit/s and 1.5 Gbit/s SATA data transfers
Supports 3.0 Gbit/s and 1.5 Gbit/s STP data transfers
Usability features:
Simplifies cabling with point-to-point, serial architecture
Provides drive spin-up sequencing control
Provides up to two LED signals for each SAS/SATA PHY to indicate drive activity and faults
Provides an SGPIO interface
3.5 External Flash Memory
The SAS I/O module provides a non-volatile 2X8Mbit Flash memory device that stores the
configuration data and operating firmware executed by the LSI1064E embedded CPU.
3.6 PCI Express* x4 Connector
The SAS I/O Module contains one 50-pin SFF-8470 connector matching the one available on
the Intel® S5000PAL Server Board.
3.7 External 4 SAS Connector
The SAS I/O module contains a x4 SAS/SATA connector which allows connections to four
external SAS devices. The pin-out of the external SAS connector is detailed in the following
table.
Revision 1.2
Intel order number: D44901-008
13
External 4 Port SAS I/O Module (AXXSASIOMOD) Intel® I/O Expansion Modules
Revision 1.2
Table 3. External SAS x4 Connector Pin-Out
Pin Name
S1 SAS0_C_RX_DP
S2 SAS0_C_RX_DN
S3 SAS1_C_RX_DP
S4 SAS1_C_RX_DN
S5 SAS2_C_RX_DP
S6 SAS2_C_RX_DN
S7 SAS3_C_RX_DP
S8 SAS3_C_RX_DN
S9 SAS3_C_TX_DN
S10 SAS3_C_TX_DP
S11 SAS2_C_TX_DN
S12 SAS2_C_TX_DP
S13 SAS1_C_TX_DN
S14 SAS1_C_TX_DP
S15 SAS0_C_TX_DN
S16 SAS0_C_TX_DP
1 GND
2 GND
3 GND
4 GND
5 GND
6 GND
7 GND
8 GND
9 GND
10 GND
11 GND
Intel order number: D44901-008
14
Intel® I/O Expansion Modules InfiniBand* (SDR) Module (AXXIBIOMOD)
4. InfiniBand* (SDR) Module (AXXIBIOMOD)
The 4X SDR InfiniBand* I/O module is based on the Mellanox InfiniHost* MT25204 device with
the integrated Physical Layer SerDes. This card has a single 4X InfiniBand* copper port for
connecting InfiniBand* traffic at up to 10Gbps. This section provides a high-level description of
the implementation of this I/O module. This module is expected to end-of-life with the
S5000PAL/S5400SF server boards, not available for extended life support
Figure 10. Single InfiniBand* (SDR) Module (AXXIBIOMOD)
4.1 Feature Set
The InfiniBand* I/O module supports the following feature set:
3.3V 4x PCI Express* interface
InfiniHost* Lx MT25204 controller chip with integrated InfiniBand* SerDes
One 10Gbps copper port (with 4X IB connector)
16MBits SPI Flash memory for firmware and configuration
32KBytes EEPROM for VPD data
LEDs for physical and logical link status
Power supply circuitry that generates 1.8V and 1.2V rails
Revision 1.2
Intel order number: D44901-008
15
InfiniBand* (SDR) Module (AXXIBIOMOD) Intel® I/O Expansion Modules
Revision 1.2
Intel order number: D44901-008
16
4.2 Functional Block Diagram
Figure 11. InfiniBand* I/O Module Block Diagram
InfiniHost* LX
IB Controller
InfiniBand* 4X Copper
(HIB-B16LFYGCA)
Port 1
InfiniBand*
Port LEDs
SPI Flash
16Mbits
Block Diagram
1.8 V Power
Regulator
1.2 V Power
Regulator
LTC1772
PCIe* 3.3V
PCI Express* Interface Custom BTB
Connector (PN: AEA-BTB-034)
(
A
P-
A
E
A
-BTB-034
)
VPD
EEPROM
32K Bytes
Intel® I/O Expansion Modules InfiniBand* (SDR) Module (AXXIBIOMOD)
4.3 Mechanical Dimensions
Figure 12. InfiniBand* I/O Module Dimensions; Top and Side Views
Revision 1.2
Intel order number: D44901-008
17
InfiniBand* (SDR) Module (AXXIBIOMOD) Intel® I/O Expansion Modules
Figure 13. InfiniBand* I/O Module Dimensions; Bottom View
4.4 LED Functionality
The InfiniBand* I/O module has two LEDs for debug only. They are not visible from the rear
panel.
Physical Link LED (Green)
Steady On: Physical link established
Off: Physical link error, poor connection quality, or no physical connection
Activity LED (Yellow)
Steady On: Data transferring to/from the card across the wire (solid stream)
Blinking: Data transferring to/from the card across the wire
Off: Logical link error or no Rx Char detected
Revision 1.2
Intel order number: D44901-008
18
Intel® I/O Expansion Modules InfiniBand* (SDR) Module (AXXIBIOMOD)
Revision 1.2
Intel order number: D44901-008
19
4.5 PCI Express* x4 Connector
The InfiniBand* I/O Module contains one 50-pin connector.
4.6 External Connector
The InfiniBand* I/O module contains an x4 InfiniBand* connector which allows a 10 Gbps
connection to the InfiniBand* Fabric.
Internal 4-port LSI 1064e SAS I/O Module (AXX4SASMOD) Intel® I/O Expansion Modules
5. Internal 4-port LSI 1064e SAS I/O Module
(AXX4SASMOD)
The optional Intel® SAS Entry RAID Module AXX4SASMOD includes a SAS1064e controller that
supports x4 PCI Express* link widths and is a single-function PCI Express* end-point device.
The SAS controller supports the SAS protocol as described in the Serial Attached SCSI
Standard, version 1.0, and also supports SAS 1.1 features. A 32-bit external memory bus off the
SAS1064e controller provides an interface for Flash ROM and NVSRAM (Non-volatile Static
Random Access Memory) devices.
The optional Intel® SAS Entry RAID Module AXX4SASMOD provides four SAS connectors that
support up to four hard drives with a non-expander backplane or up to eight hard drives with an
expander backplane.
For more details refer to the Intel® SAS Entry RAID Module Hardware Specification.
5.1 Major Component Diagram
Connector Reference Designators Connector
Type
Pin Count
SAS Connector 0-3 J1B2, J2B1, J3B2, J3B3 Header 7
SES J2A1 Header 3
SGPIO J2A2 Header 4
Software RAID 5 Key
Header
J1A1 Key holder 3
SAS Module Connector J3M1 Mezzanine slot 50
Figure 14. Intel® SAS Entry RAID Module AXX4SASMOD Component and Connector
Revision 1.2
Intel order number: D44901-008
20
Intel® I/O Expansion Modules Internal 4-port LSI 1064e SAS I/O Module (AXX4SASMOD)
5.2 Functional Block Diagram
Figure 15. Intel® SAS Entry RAID Module AXX4SASMOD Functional Block Diagram
5.3 Feature Set
LSI* LSISAS1064E SAS/SATA controller
Four-port, 3.0 Gbit/s SAS/SATA controller
Integrated Arm966 microprocessor core
Compliant with Fusion-MPT* architecture
x4 PCI Express*
Provides 4 SAS/SATA ports for connecting multiple SAS/SATA devices
Intel® Embedded Server RAID Technology II mode provides RAID 0, RAID 1, RAID 10, and
RAID 5 support. RAID 5 is available with optional RAID 5 activation key accessory
(AXXRAKSW5).
IT/IR RAID mode supports entry hardware RAID 0, RAID 1, RAID 10, RAID 10E, and native
SAS pass through mode.
Serial General Purpose Input/Output (SGPIO) connector and SCSI Enclosure Services
(SES) support for hard drive backplane LED control
Revision 1.2
Intel order number: D44901-008
21
Internal 4-port LSI 1064e SAS I/O Module (AXX4SASMOD) Intel® I/O Expansion Modules
Table 4. AXX4SASMOD Storage Mode
Storage
Mode Description RAID Types and
Levels Supported Driver
RAID
Management
Software
RAID
Software
User’s Guide
IT/IR RAID
4 SAS Ports
Up to 10 SAS
or SATA drives
via expander
backplanes
Native SAS pass
through mode without
RAID function.
Entry Hardware
RAID.
RAID 1 (IM
mode)
RAID 10/10E
(IME mode)
RAID 0 (IS
Mode)
SAS MPT
driver (Fully
open-source
driver)
Broad OS
support
Inte RAID Web
Console 2
IT/IR RAID
Software
User’s Guide
SW RAID
4 SAS Ports
Up to 8 SAS or
SATA drives
via expander
backplanes
SW RAID 0/1/10
standard
SW RAID 5 with
optional
AXXRAKSW5
ESRTII Driver
Microsoft
Windows* and
selected
Linux*
Versions only
Intel RAID
Web Console 2
Intel RAID
Software
User’s Guide
5.4 Mechanical Drawings
Figure 16. AXX4SASMOD Mechanical Dimensions (Top View)
Revision 1.2
Intel order number: D44901-008
22
Intel® I/O Expansion Modules Internal 4-port LSI 1064e SAS I/O Module (AXX4SASMOD)
Revision 1.2
Figure 17. AXX4SASMOD Mechanical Dimensions (Bottom View)
Intel order number: D44901-008
23
Intel® Integrated RAID Module SROMBSASMR (AXXROMBSASMR) Intel® I/O Expansion Modules
6. Integrated RAID Module SROMBSASMR
(AXXROMBSASMR)
The Internal 4-port SAS module based on LSI 1078e* controller supports RAID hardware. For
more information, refer to the Intel® Integrated RAID Controller SROMBSASMR
(AXXROMBSASMR) Technical Product Specification.
6.1 Product Overview
The Intel® Integrated RAID Controller SROMBSASMR supports both enterprise-class serial ATA
(SATA) and serial-attached SCSI (SAS) disk drives, which allows customized solutions for
performance, reliability, system expansion flexibility, and hard drive capacity. It provides such
flexibility and helps lower the total cost of ownership with a standardized server and storage
infrastructure.
This RAID controller is designed with four internal SAS/SATA ports through four individual
connectors and uses a custom board-to-board 50-pin connector to provide x4 PCI Express*
support.
6.2 Hardware Architectural Features
Table 5. Hardware Architectural Features
Feature Intel Integrated RAID Controller SROMBSASMR
RAID Levels 0, 1, 5, 6, 10, 50, 60
Number of devices Up to 16 devices per controller
Device types SAS and SATA hard drives
Data transfer rate 300 MB/s per port
PCI bus 50-pin board-to-board connector with x4 PCI Express*
Memory 128 MB ECC DDR2 667 MHz SDRAM Integrated on the
controller
Battery backup (optional) Intel
®
RAID Smart Battery AXXRSBBU3
SAS/SATA connector Four internal SAS/SATA connectors
ROC LSI* 1078 SAS ROC which performs hardware-exclusive OR
(XOR) assistance
Weight 46 oz
Serial port 4-pin serial debug (requires transceiver)
Compatible devices 16 physical devices, 64 logical drives, mixed capacity, SAS and
SATA hard drives; non-disk devices including expanders
Firmware 4 MB in flash ROM
Revision 1.2
Intel order number: D44901-008
24
Intel® I/O Expansion Modules Intel® Integrated RAID Module SROMBSASMR (AXXROMBSASMR)
6.3 Block Diagram
Figure 18. Hardware Block Diagram
6.4 Controller Layout
Figure 19. Intel® Integrated RAID Controller SROMBSASMR Physical Layout
Revision 1.2
Intel order number: D44901-008
25
Intel® Integrated RAID Module SROMBSASMR (AXXROMBSASMR) Intel® I/O Expansion Modules
6.4.1 Mechanical Drawings
Figure 20. Primary Side
Figure 21. Secondary Side
Revision 1.2
Intel order number: D44901-008
26
Intel® I/O Expansion Modules Intel® Integrated RAID Module SROMBSASMR (AXXROMBSASMR)
Revision 1.2
6.4.2 Jumpers and Connectors
Jumper/Connector Description Type Comments
J1-J4 Internal SAS/SATA Port
Connector, Ports 0-3 N/A
Connection to SAS/SATA
devices:
J1 = SAS/SATA
Port 0
J2 = SAS/SATA
Port 1
J3 = SAS/SATA
Port 2
J4 = SAS/SATA
Port 3
J5 Board-to-board Connector
for Battery Backup Unit
20-pin
connector
Provides an interface to the
daughter card that contains the
battery backup unit.
J6
Universal Asynchronous
Receiver/Transmitter
(UART)
4-pin connector For factory and debug use
J7 Keyed I2C Connector 3-pin keyed
connector
Out-of-band enclosure
management (SES2)
J8 Debug Connector 4-pin connector Reserved
Figure 22. Jumpers and Connectors
Intel order number: D44901-008
27
Quad Port GbE I/O Module (AXX4GBIOMOD2) Intel® I/O Expansion Modules
7. Quad Port GbE I/O Module (AXX4GBIOMOD2)
The dual Intel® 82576 Gb NIC I/O module provides four additional 1 Gbit external Ethernet
connections.
Figure 23. Quad-Port GbE I/O Module (AXX4GBIOMOD2)
7.1 Feature Set
The quad-port Gb Ethernet I/O module supports the following feature set:
Intel® 82576 Gb Ethernet Controller
Dual Ethernet Interface
Support IOAT V3.0
Virtualization Ready
PCI Express* x4 Gen2 interface
Supports four external 1 Gb Ethernet ports by using two NIC chips.
Revision 1.2
Intel order number: D44901-008
28
Intel® I/O Expansion Modules Quad Port GbE I/O Module (AXX4GBIOMOD2)
7.2 Functional Block Diagram
Figure 24. Quad-port Gigabit Ethernet I/O Module Block Diagram
Intel
®
82576
Two 50
p
in BTB Connector
Intel
®
5500
Series
Chipset
Server Board RJ45 Connector
RJ45 Connector
PCIe* x4
Intel
®
82576
PCIe* x8
RJ45 Connector
PCIe* x4
RJ45 Connector
Revision 1.2
Intel order number: D44901-008
29
Quad Port GbE I/O Module (AXX4GBIOMOD2) Intel® I/O Expansion Modules
7.3 Mechanical Drawings
Figure 25. Quad-Port GbE I/O Module Mechanical Drawing
Revision 1.2
Intel order number: D44901-008
30
Intel® I/O Expansion Modules Quad Port GbE I/O Module (AXX4GBIOMOD2)
Figure 26. Quad-Port GbE I/O Module Mechanical Drawing
7.4 Intel® 82576 1 Gb Ethernet Controller
The Intel® 82576 1 Gb Ethernet Controller is a single, compact component with two fully
integrated 1 Gb Ethernet Media Access Control (MAC).
The Intel® 82576 supports X4 PCI-Express Gen2 connection, and support I/OAT V3.0
(Input/Output Acceleration Technology). These give the device a high-performance and low-
host memory access latency feature. In addition, the wide internal data path eliminates
performance bottlenecks by efficiently handling large address and data words. To further
optimize the latency from system level, the PCI-Express* x8 interface is directly connected to
IOH.
7.5 EEPROM
The Quad Port Gb Ethernet I/O module provides a SPI serial EEPROM to store configuration
and informational data. This includes pre-boot configuration data, MAC address, and serial
numbers for the 82576.
Revision 1.2
Intel order number: D44901-008
31
Quad Port GbE I/O Module (AXX4GBIOMOD2) Intel® I/O Expansion Modules
Revision 1.2
Intel order number: D44901-008
32
7.6 PCI Express* x8 Connector
The I/O module contains two 50-pin connectors to provide X8 PCI Express* Gen2 interface.
They mate with I/O module connector available on the Intel® Server Boards S3420GPRX,
S5520UR and S5500WB.
7.7 Gbit Ethernet Connector
The Quad Port Gb Ethernet I/O module contains four 1 Gbit Ethernet Magjack connectors.
Intel® I/O Expansion Modules Dual Port 10GbE I/O Module (AXX10GBIOMOD)
8. Dual Port 10GbE I/O Module (AXX10GBIOMOD)
The dual 10 Gb I/O module provides two 10 Gbit external Ethernet connections. This section
provides a high level description of the implementation of this I/O module.
.
Figure 27. Dual Port 10GbE I/O Module
8.1 Feature Set
The dual 10 Gb Ethernet I/O module supports the following feature set:
Intel® 82598EB 10 Gb Ethernet Controller
Dual CX4 port
Support IOAT V2.0
Virtual Queue for Virtualization
Can be implemented in small form factor for 10 Gbit Ethernet function
PCI Express* x8 Gen2 interface
Supports two external CX4 10 Gb Ethernet ports
Support active cable (copper-fiber optic-copper)
Revision 1.2
Intel order number: D44901-008
33
Dual Port 10GbE I/O Module (AXX10GBIOMOD) Intel® I/O Expansion Modules
8.2 Functional Block Diagram
Two 50-Pin Connectors
Intel
®
5500
Series
Chipset
Server Board
Figure 28. Dual 10 Gb Ethernet I/O Module Block Diagram
Intel
®
82598EB
PCIe* x8
CX4
PCIe* x8
EEPROM
CX4 Connector
CX4
CX4 Connector
Revision 1.2
Intel order number: D44901-008
34
Intel® I/O Expansion Modules Dual Port 10GbE I/O Module (AXX10GBIOMOD)
8.3 Mechanical Drawings
Figure 29. Dual 10 Gb Ethernet I/O Module Dimensions: Top and Side Views
Revision 1.2
Intel order number: D44901-008
35
Dual Port 10GbE I/O Module (AXX10GBIOMOD) Intel® I/O Expansion Modules
Figure 30. Dual 10 Gb Ethernet I/O Module Dimensions: Bottom View
8.4 Intel® 82598 10 Gb Ethernet Controller
The Intel® 82598EB 10 Gb Ethernet Controller is a single, compact component with two fully
integrated 10 Gb Ethernet Media Access Control (MAC) and XAUI ports.
The Intel® 82598EB is a follow-on design to the prior generations of Intel® 1Gbit, 10 Gbit
Ethernet controllers. It provides new features and retains many of its predecessors’ features.
The Intel® 82598EB supports X8 PCI-Express Gen2 connection and I/OAT V2.0 (Input/Output
Acceleration Technology). These give the device a high-performance and low-host memory
access latency feature. In addition, the wide internal data path eliminates performance
bottlenecks by efficiently handling large address and data words. The parallel and pipelined
logic combined architecture is optimized for Ethernet and independent transmit and receive
queues, this means the 82598EB can process the packet with minimum latency. To further
optimize the latency from system level, the PCI-Express* x8 interface is connected to IOH
directly.
Revision 1.2
Intel order number: D44901-008
36
Intel® I/O Expansion Modules Dual Port 10GbE I/O Module (AXX10GBIOMOD)
Revision 1.2
Intel order number: D44901-008
37
8.5 EEPROM
The Dual Gb Ethernet I/O module provides a SPI serial EEPROM to store configuration and
informational data. This includes pre-boot configuration data, MAC addresses, SMBus Address,
and serial numbers for the 82598EB.
8.6 PCI Express* x8 Connector
The Dual 10 Gb Ethernet I/O module contains two 50-pin connectors to provide x8 PCI
Express* Gen2 interface. They mate with I/O module connector available on the Intel® Server
Boards S5520UR and S5500WB.
8.7 CX4 Ethernet Connector
The Dual Gb Ethernet I/O module contains two CX4 10 Gbit Ethernet connectors compatible
with 10 Gbit Ethernet CX4 connections. The CX4 port embeds the feature which can support
active cable (copper-fiber optic – copper), so it enlarges the distance of the 10 Gbit Ethernet
connections from 10 m up to 100 m.
InfiniBand* (QDR) I/O Modules Intel® I/O Expansion Modules
9. InfiniBand* (QDR) I/O Modules
The 4X InfiniBand* QDR I/O module is based on the Mellanox InfiniHost* MT25408 device with
the integrated Physical Layer SerDes. This card has a single 4X InfiniBand* copper port for
connecting InfiniBand* traffic at up to 40Gbps. This section provides a high-level description of
the implementation of this I/O module.
9.1 Support Matrix
Table 6. Support Matrix Data
Product Code MM# S5520UR S5500WB SR1680MV
AXXIBQDRIOMOD 902559 Yes No No
AXXIBQDRSR169X 909786 No Yes No
AXXIBQDRIOMV 904810 No No Yes
Figure 31. AXXIBQDRIOMO
Figure 32. AXXIBQDRSR169X
Revision 1.2
Intel order number: D44901-008
38
Intel® I/O Expansion Modules InfiniBand* (QDR) I/O Modules
Figure 33. AXXIBQDRIOMV
9.2 Feature List
The InfiniBand* QDR I/O module supports the following feature set:
8x PCI Express* Gen2 interface
InfiniHost* MT25408 controller chip with integrated InfiniBand* SerDes
One 40Gbps copper port (with 4X IB connector)
16MBytes SPI Flash memory for firmware and configuration
LEDs for physical and logical link status
Power supply circuitry that generates 1.2V, 1.8V and 1.2V rails
9.3 Functional Block Diagram
Figure 34. InfiniBand* (QDR) I/O Module Block Diagram
Revision 1.2
Intel order number: D44901-008
39
InfiniBand* (QDR) I/O Modules Intel® I/O Expansion Modules
Revision 1.2
Intel order number: D44901-008
40
9.4 LED Functionality
The InfiniBand* I/O module has two debug LEDs. They are not visible from the rear panel.
Physical Link LED (Green)
Steady On: Physical link established
Off: Physical link error, poor connection quality, or no physical connection
Activity LED (Yellow)
Steady On: Data transferring to/from the card across the wire (solid stream)
Blinking: Data transferring to/from the card across the wire
Off: Logical link error or no Rx Char detected
9.5 PCI Express* x4 Connector
The InfiniBand* I/O Module contains two 50-pin connectors
9.6 External Connector
The InfiniBand* I/O module contains an x4 InfiniBand* connector which allows a 40 Gbps
connection to the InfiniBand* Fabric.
Intel® I/O Expansion Modules Intel® Integrated RAID Module RMS2MH080
10. Intel® Integrated RAID Module RMS2MH080
The Inte Integrated RAID Module RMS2MH080 is an intelligent custom board-to-board PCI
Express* 2.0 compliant interface RAID adapter with an integrated LSI* SAS2108 RAID-On-Chip
chipset, providing both a SAS controller and RAID engine. With 512MB RAM built onto the
board and eight independent ports supporting 6-Gbps and 3 Gbps SAS data transfers using two
SFF-8087 mini multi-lane connectors, this controller supports up to 32 enterprise-class SAS or
SATA devices and 64 logical drives. The PCI Express* connector fits into a 50 pin connector
capable of performance up to 5 Gbps per lane. Support for intelligent XOR RAID levels 0, 1, 5,
6, 10, 50, and 60. For more details see the Intel® Integrated RAID Module RMS2MH080
(AXXRMS2MH080) Hardware User’s Guide.
10.1 Technical Specifications
Table 7. RMS2MH080 Specifications
Specification Intel
®
Integrated RAID Module
RMS2MH080
Processor LSI* 2108 Integrated RAID on Chip 800MHz
Operating voltage +3.3 V
Interface to host Custom board-to-board x8 PCI Express* 2.0 compliant
interface
SATA Bus Speed Up to 6 Gbps per port, point-to-point
SAS/SATA ports 2x4 internal ports, 16 devices
Physical and virtual drive support 16 drivers per controller and 64 logical devices
Firmware 8 MB in reflashable flash ROM
Compatible devices •2.5-inch and 3.5-inch SAS or SATA II
drives including SSD drives
•Non disk devices including expanders
•Can support drives of mixed capacity
Cabling Small thin cables that do not restrict airflow
and Shared connectors for multiple drives
Redundant configuration 32 KB NVRAM and config-on-disk (COD)
Enclosure Management In-band and out-of-band
Enclosure Support Assumes one SEP per enclosure
Revision 1.2
Intel order number: D44901-008
41
Intel® Integrated RAID Module RMS2MH080 Intel® I/O Expansion Modules
Figure 35. RMS2MH080 Card Layout
Jumper Description Type Comments
J1 – J2 Internal mini SAS Port
Connectors, Ports 0-3 and
4-7
Connection to SAS/SATA
devices:
• J1 = SAS_A (Port 0-3)
• J2 = SAS_B (Port 4-7)
J3 Board-to-board connector
for Battery Backup Unit
20-pin connector Provides an interface to the
daughter card that contains
the battery backup unit.
J4 Keyed I2C Connector 3-pin keyed
connector
Out-of-band enclosure
management (SES2).
J5 RAID Premium Feature
Key Header
2-pin connector Enables support for RAID
Premium Feature.
J6 UART debug header 4-pin connector Factory use only (may be
removed in future)
J7 Bootstrap CONFIG header 4-pin connector Factory use only (may be
removed in future)
Revision 1.2
Intel order number: D44901-008
42
Intel® I/O Expansion Modules Intel® Integrated RAID Module RMS2MH080
Revision 1.2
Figure 36. RMS2MH080 Block Diagram
Intel order number: D44901-008
43
Integrated RAID Module RMS2AF040 & RMS2AF080 Intel® I/O Expansion Modules
11. Integrated RAID Module RMS2AF040 &
RMS2AF080
The Intel® Integrated RAID Module RMS2AF040 and RMS2AF080 are intelligent custom board-
to-board PCI Express* 2.0 compliant interface RAID adapters with an integrated LSI*
LSISAS2008 Processor Chip, providing both a SAS controller and RAID engine. With four
(RMS2AF040) or eight (RMS2AF080) independent ports supporting 6 Gbps and 3 Gbps SAS
data transfers using four or eight individual SAS/SATA connectors, this controller supports up to
32 enterprise-class SAS or SATA devices and 64 logical drives. The PCI Express* connector
fits into a 50 pin connector capable of performance up to 5 Gbps per lane. Support for intelligent
XOR RAID levels 0, 1, 5, 10, and 50. For more details see the Intel® Integrated RAID Module
RMS2AF040 (AXXRMS2AF040) and RMS2AF080 (AXXRMS2AF080) Hardware User’s Guide.
Revision 1.2
Intel order number: D44901-008
44
Intel® I/O Expansion Modules Integrated RAID Module RMS2AF040 & RMS2AF080
11.1 Technical Specifications
Table 8. RMS2AF0#0 Specifications
Specification Intel
®
Integrated RAID Module
RMS2AF040 and RMS2AF080
Processor LSI* LSISAS2008 PCI* Express-SAS/SATA
I/O Processor chip, 150MHz
Operating voltage +3.3 V
Interface to host Custom board-to-board x8 PCI Express* 2.0
compliant interface
SATA Bus Speed Up to 6 Gbps per port, point-to-point
SAS/SATA ports Four internal ports for RMS2AF040 and eight
internal ports for RMS2AF080
Physical and virtual drive support Up to 64 physical drives including up to 16
physical drives in up to 16 RAID arrays per
controller.
Drives not configured as part of a RAID array
can be configured as “pass through” drives in
Non-RAID mode.
Firmware 16 MB in reflashable flash ROM
Compatible devices
2.5-inch and 3.5-inch SAS or SATA II
drives including SSD drives
Non disk devices including expanders
Can support drives of mixed capacity
Cabling Small thin cables that do not restrict airflow
and Shared connectors for multiple drives
Redundant configuration 32 KB NVRAM and config-on-disk (COD)
Enclosure Management In-band and out-of-band SES2; out-of-band
SGPIO
Enclosure Support Assumes one SEP per enclosure
Revision 1.2
Intel order number: D44901-008
45
Integrated RAID Module RMS2AF040 & RMS2AF080 Intel® I/O Expansion Modules
11.2 Intel® Integrated RAID Module RMS2AF0x0 Characteristics
Jumper Description Type Comments
J1 – J8 Internal SAS/SATA Port
Connectors, Ports 0-7
Connection to SAS/SATA devices:
• J1 = SAS/SATA Port 0
• J2 = SAS/SATA Port 1
• J3 = SAS/SATA Port 2
• J4 = SAS/SATA Port 3
• J5 = SAS/SATA Port 4
• J6 = SAS/SATA Port 5
• J7 = SAS/SATA Port 6
• J8 = SAS/SATA Port 7
J5 - J8 (Ports 4 - 7) are only available
on Intel® RAID Module RMS2AF080
J9 Keyed SGPIO Connector 4-pin keyed
connector
Enclosure management (SGPIO) for
Ports 4-7 The connector is not available
on Intel® RAID Module RMS2AF040
J10 Keyed SGPIO Connector 4-pin keyed
connector
Enclosure management (SGPIO) for
Ports 0-3
J11 Keyed I2C Connector 3-pin keyed
connector
Out-of-band enclosure management
(SES2)
Figure 37. RMS2AF080 Card Layout
Revision 1.2
Intel order number: D44901-008
46
Intel® I/O Expansion Modules Integrated RAID Module RMS2AF040 & RMS2AF080
Revision 1.2
Figure 38. RMS2AF040 Hardware Block Diagram
Figure 39. RMS2AF080 Hardware Block Diagram
Intel order number: D44901-008
47
Integrated RAID Module RMS2LL040 & RMS2LL080 Intel® I/O Expansion Modules
12. Integrated RAID Module RMS2LL040 &
RMS2LL080
The Intel® RAID Module RMS2LL040 and RMS2LL080 are intelligent custom board-to-board
PCI Express* 2.0 compliant interface RAID adapters with an integrated LSI* LSISAS2008
Processor Chip, providing both a SAS controller and RAID engine. With four (RMS2LL040) or
eight (RMS2LL080) independent ports supporting 6-Gbps and 3 Gbps SAS data transfers using
four or eight individual SAS/SATA connectors, this controller supports up to 32 enterprise-class
SAS or SATA devices and 64 logical drives. The PCI Express* connector fits into a 50 pin
connector capable of performance up to 5 Gbps per lane. Includes support for RAID levels 0, 1,
and 1E. For more details see the Intel® Integrated RAID Module RMS2LL040 (AXXRMS2LL040)
and RMS2LL080 (AXXRMS2LL080) Hardware User’s Guide.
Revision 1.2
Intel order number: D44901-008
48
Intel® I/O Expansion Modules Integrated RAID Module RMS2LL040 & RMS2LL080
12.1 Technical Specifications
Table 9. RMS2LL0#0 Specifications
Specification Intel
®
Integrated RAID Module
RMS2LL040 and RMS2LL080
Processor LSI* LSISAS2008 PCI* Express-SAS/SATA
I/O Processor chip, 150MHz
Operating voltage +3.3 V
Interface to host Custom board-to-board x8 PCI Express* 2.0
compliant interface
SATA Bus Speed Up to 6 Gbps per port, point-to-point
SAS/SATA ports 4 internal ports for RMS2LL040 and 8
internal ports for RMS2LL080
Physical and virtual drive support Up to 64 physical drives including up to 16
physical drives in up to 16 RAID arrays per
controller.
Drives not configured as part of a RAID array
can be configured as “pass through” drives in
Non-RAID mode.
Firmware 16 MB in reflashable flash ROM
Compatible devices •2.5-inch and 3.5-inch SAS or SATA II
drives including SSD drives
•Non disk devices including expanders
•Can support drives of mixed capacity
Cabling Small thin cables that do not restrict airflow
and Shared connectors for multiple drives
Redundant configuration 32 KB NVRAM and config-on-disk (COD)
Enclosure Management In-band and out-of-band SES2; out-of-band
SGPIO
Enclosure Support Assumes one SEP per enclosure
Revision 1.2
Intel order number: D44901-008
49
Integrated RAID Module RMS2LL040 & RMS2LL080 Intel® I/O Expansion Modules
12.2 Intel® Integrated RAID Module RMS2LL0x0 Characteristics
Jumper Description Type Comments
J1 – J8 Internal SAS/SATA Port
Connectors, Ports 0-7
Connection to SAS/SATA devices:
• J1 = SAS/SATA Port 0
• J2 = SAS/SATA Port 1
• J3 = SAS/SATA Port 2
• J4 = SAS/SATA Port 3
• J5 = SAS/SATA Port 4
• J6 = SAS/SATA Port 5
• J7 = SAS/SATA Port 6
• J8 = SAS/SATA Port 7
J5 - J8 (Ports 4 - 7) are only available
on Intel® RAID Module RMS2LL080
J9 Keyed SGPIO Connector 4-pin keyed
connector
Enclosure management (SGPIO) for
Ports 4-7 The connector is not available
on Intel® RAID Module RMS2LL040
J10 Keyed SGPIO Connector 4-pin keyed
connector
Enclosure management (SGPIO) for
Ports 0-3
J11 Keyed I2C Connector 3-pin keyed
connector
Out-of-band enclosure management
(SES2)
Figure 40. Intel® Integrated RAID Module RMS2LL0x0 Characteristics
Revision 1.2
Intel order number: D44901-008
50
Intel® I/O Expansion Modules Integrated RAID Module RMS2LL040 & RMS2LL080
Revision 1.2
Figure 41. RMS2LL040 Hardware Block Diagram
Figure 42. RMS2LL080 Hardware Block Diagram
Intel order number: D44901-008
51