KAD2708C - Kenet, Inc. - Datasheet.Live

KAD2708C

300 Unicorn Park Dr., Woburn, MA 01801 Sales: 1-781-497-0060 Sales@kenetinc.com

Rev 1.1 Page 1 of 17

Description

The Kenet KAD2708C is the industry’s lowest power,

8-bit, high performance Analog-to-Digital converter.

The converter runs at sampling rates up to 275MSPS,

and is fabricated with Kenet’s proprietary

FemtoCharge® CMOS technology. Users can now

obtain industry-leading SNR and SFDR specifications

while nearly halving power consumption. Sampling

rates of 210, 170 and 105MSPS are also available in

the same pin-compatible package and in versions

with 10-bit resolution. Kenet’s KAD2708L offers this

performance with LVDS outputs. All are available in

68-pin RoHS-compliant QFN packages with exposed

paddle. Performance is specified over the full

industrial temperature range (-40 to +85°C).

Key Specifications

• SNR of 48.8dB at Nyquist

• SFDR of 68dBc at Nyquist

• Power consumption ≤ 265mW at fS = 275MSPS

Features

• On-chip reference

• Internal track and hold

• 1.5VPP differential input voltage

• 600MHz analog input bandwidth

• Two’s complement or binary output

• Over-range indicator

• Selectable ÷2 Clock Input

• LVCMOS compatible outputs

Applications

• High-Performance Data Acquisition

• Portable Oscilloscope

• Medical Imaging

• Cable Head Ends

• Power-Amplifier Linearization

• Radar and Satellite Antenna Array Processing

• Broadband Communications

• Local Multipoint Distribution System (LMDS)

• Communications Test Equipment

8-Bit, 275MSPS Analog-to-Digital Converter

Resolution, Speed LVDS Outputs LVCMOS Outputs

10 Bits 275MSPS KAD2710L-27 KAD2710C-27

8 Bits 275MSPS KAD2708L-27 KAD2708C-27

10 Bits 210MSPS KAD2710L-21 KAD2710C-21

8 Bits 210MSPS KAD2708L-21 KAD2708C-21

10 Bits 170MSPS KAD2710L-17 KAD2710C-17

8 Bits 170MSPS KAD2708L-17 KAD2708C-17

10 Bits 105MSPS KAD2710L-10 KAD2710C-10

8 Bits 105MSPS KAD2708L-10 KAD2708C-10

8 Bits 350MSPS KAD2708L-35

Table 1. Pin-Compatible Products

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 2 of 17

Absolute Maximum Ratings1

1. Exposing the device to levels in excess o f the maximum ratings may cause per man ent damage. Exposure

to maximum conditions for extended periods may affect device reliability.

Thermal Impedance

2. Paddle soldered to ground plane.

ESD

Electrostatic charge accumulates on humans, tools and equipment, and may discharge

through any metallic package contacts (pins, balls, exposed paddle, etc.) of an integrated

circuit. Industry-standard protection techniques have been utilized in the design of this prod-

uct. However, reasonable care must be taken in the storage and handling of ESD sensitive

products. Contact Kenet for the specific ESD sensitivity rating of this product.

Parameter Min Max Unit

AVDD2 to AVSS -0.4 2.1 V

OVDD2 to OVSS -0.4 2.1 V

Analog Inputs to AVSS -0.4 AVDD3 + 0.3 V

Clock Inputs to AVSS -0.4 AVDD2 + 0.3 V

Logic Inputs to AVSS (VREFSEL, CLKDIV) -0.4 AVDD3 + 0.3 V

Logic Inputs to OVSS (RST, 2SC) -0.4 OVDD2 + 0.3 V

Operating Temperature -40 85 °C

Storage Temperature -65 150 °C

Junction Temperature 150 °C

AVDD3 to AVSS -0.4 3.7 V

Logic Output Currents 10 mA

CMOS Output Currents 20 mA

VREF TO AVSS -0.4 AVDD3 + 0.3 V

Analog Output Currents 10 mA

Parameter Symbol Typ Unit

Junction to Paddle2 JP 30 °C/W

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 3 of 17

Electrical Specifications

All specifications apply under the following conditions unless otherwise noted: AVDD2 = 1.8V, AVDD3 = 3.3V,

OVDD = 1.8V. TA = -40°C to +85°C, Typ values at 25°C. fSAMPLE = 275MSPS fIN = Nyquist.

DC Specifications

Parameter Symbol Conditions Min Typ Max Units

Power Requirements

1.8V Analog Supply Voltage AVDD2 1.7 1.8 1.9 V

3.3V Analog Supply Voltage AVDD3 3.15 3.3 3.45 V

1.8V Output Supply Voltage OVDD 1.7 1.8 1.9 V

1.8V Analog Supply Current IAVDD2 44 mA

3.3V Analog Supply Current IAVDD3 41 mA

1.8V Output Supply Current IOVDD 26 mA

Power Dissipation PD 261 mW

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 4 of 17

Analog Specifications

AC Specifications

Parameter Symbol Conditions Min Typ Max Units

Analog Input

Full-Scale Differential Analog Input Voltage VIN 1.4 1.5 1.6 VPP

Gain Temperature Coefficient AVTC Full Temp 90 ppm/ºC

Full Power Bandwidth FPBW 600 MHz

Clock Input

Sampling Clock Frequency Range fSAMPLE 50 275 MHz

CLKP, CLKN P-P Differential Input Voltage VCDI 0.5 1.8 VPP

CLKP, CLKN Differential Input Resistance RCDI 10 M

CLKP, CLKN Common-Mode Input Voltage VCCI 0.9 V

Reference

Internal Reference Voltage VREF 1.18 1.21 1.24 V

Reference Voltage Temperature Coefficient VRTC Full Temp 38 ppm/°C

Common-Mode Output Voltage VCM 0.86 V

Parameter Symbol Conditions Min Typ Max Units

Signal to Noise Ratio SNR Full Temp 45.8 48.8 dB

Signal to Noise and Distortion SINAD Full Temp 45.7 48.7 dB

Effective Number of Bits ENOB Full Temp 7.3 7.8 Bits

Spurious Free Dynamic Range SFDR Full Temp 63 68 dBc

Two-Tone SFDR 2TSFDR f1=133MHz, f2=135MHz 67 dBc

Differential Nonlinearity DNL -0.3 ±0.2 0.4 LSB

Power Supply Rejection Ratio PSRR 42 66 dB

Word Error Rate WER 1x10-12

Integral Nonlinearity INL -0.8 ±0.2 0.8 LSB

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 5 of 17

Digital Specifications

Parameter Symbol Conditions Min Typ Max Units

Inputs

High Input Voltage (VREFSEL) VREFSEL VIH 0.8*AVDD3 V

Low Input Voltage (VREFSEL) VREFSEL VIL 0.2*AVDD3 V

Input Current High (VREFSEL) VREFSEL IIH VIN = AVDD3 0 1 10 µA

Input Current Low (VREFSEL) VREFSEL IIL VIN = AVSS 25 65 75 µA

High Input Voltage (CLKDIV) CLKDIV VIH 0.8*AVDD3 V

Low Input Voltage (CLKDIV) CLKDIV VIL 0.2*AVDD3 V

Input Current High (CLKDIV) CLKDIV IIH VIN = AVDD3 25 65 75 µA

Input Current Low (CLKDIV) CLKDIV IIL VIN = AVSS 0 1 10 µA

High Input Voltage (RST,2SC) RST,2SC VIH 0.8*OVDD2 V

Low Input Voltage (RST,2SC) RST,2SC VIL 0.2*OVDD2 V

Input Current High (RST,2SC) RST,2SC IIH VIN = OVDD 0 1 10 µA

Input Current Low (RST,2SC) RST,2SC IIL VIN = OVSS 25 50 75 µA

Input Capacitance CDI 3 pF

CMOS Outputs

Voltage Output High VOH 1.8 V

Voltage Output Low VOL 0 V

Output Rise Time tR 1.8 ns

Output Fall Time tF 1.4 ns

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 6 of 17

Timing Diagram

Figure 1. LVCMOS Timing Diagram

Timing Specifications

Parameter Symbol Min Typ Max Units

Aperture Delay tA 1.7 ns

RMS Aperture Jitter jA 200 fs

Input Clock to Data Propagation Delay tPD 1.8 ns

Input Clock to Output Clock Propagation Delay tCPD 1.3 ns

Output Clock to Data Propagation Delay tDC 470 ps

Output Data to Output Clock Setup Time tSU 3 ns

Output Clock to Output Data Hold Time tH 75 ps

Latency (Pipeline Delay) L 28 cycles

Over Voltage Recovery tOVR 1 cycle

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 7 of 17

Pin Descriptions

Pin # Name Function

1, 14, 18, 20 AVDD2 1.8V Analog Supply

2, 7, 10, 19, 21, 24 AVSS Analog Supply Return

3 VREF Reference Voltage Out/In

4 VREFSEL Reference Voltage Select (0:Int 1:Ext)

5 VCM Common Mode Voltage Output

6, 15, 16, 25 AVDD3 3.3V Analog Supply

8, 9 INP, INN Analog Input Positive, Negative

11-13, 29-36, 37, 39, 42, 46, 48,

50, 53, 54, 56, 58, 62, 63, 67

DNC Do Not Connect

17 CLKDIV Clock Divide by Two (Active Low)

22, 23 CLKN, CLKP Clock Input Complement, True

26, 45, 61 OVSS Output Supply Return

27, 41, 44, 60 OVDD2 1.8V CMOS Supply

28 RST Power On Reset (Active Low)

38 D0 LVCMOS Bit 0 (LSB) Output

40 D1 LVCMOS Bit 1 Output

43 CLKOUT LVCMOS Clock Output

47 D2 LVCMOS Bit 2 Output

49 D3 LVCMOS Bit 3 Output

51 D4 LVCMOS Bit 4 Output

53 D5 LVCMOS Bit 5 Output

55 D6 LVCMOS Bit 6 Output

57 D7 LVCMOS Bit 7 Output

59 OR Over Range

64-66 Connect to OVDD2

68 2SC Two’s Complement Select (Active Low)

Exposed Paddle AVSS Analog Supply Return

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 8 of 17

Pin Configuration

Figure 2. Pin Configuration

2SC

DNC

OVDD2

DNC

OVSS

OVDD2

ORP

DNC

AVDD2

AVSS

AVDD2

AVSS

CLKN

CLKP

AVSS

AVDD3

OVSS

OVDD2

RST

DNC

AVDD2

AVSS

VREF

VREFSEL

VCM

AVDD3

AVSS

INP

INN

AVSS

DNC

AVDD2

AVDD3

CLKDIV

Top View

Not to Scale

DNC

OVSS

OVDD2

CLKOUT

DNC

OVDD2

DNC

68 QFN

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 9 of 17

-80

-70

-60

-50

-40

-30

-30 -25 -20 -15 -10 -5 0

Input Amplitude (dBFS)

HD2, HD3 dB

Typical Operating Characteristics

AVDD3=3.3V, AVDD2=OVDD2 =1.8V, TAMBIENT (TA)=25°C, fSAMPLE=275MHz, VIN=6.865MHz @ -0.5dBFS unless noted.

Figure 3. SNR vs. Vin Figure 4. SFDR vs. Vin

Figure 5. HD2, 3 vs. Vin Figure 6. Power Dissipation vs. fSAMPLE

Figure 7. SNR vs. fSAMPLE Figure 8. HD2, 3 vs. fSAMPLE

HD3

HD2

HD3

HD2

-30 -25 -20 -15 -10 -5 0

Analog Input Amplitude (dBFS)

SNR (dB)

-30 -25 -20 -15 -10 -5 0

Input Amplitude (dBFS)

SFDR (dB

)

-90

-85

-80

-75

-70

-65

50 75 100 125 150 175 200 225 250 275 300

fSAMPLE (MHz)

dBc

48.5

49.5

50 75 100 125 150 175 200 225 250 275 300

fSAMPLE (MHz)

SNR (dB)

100

120

140

160

180

200

220

240

260

280

50 100 150 200 250 300

fSAMPLE (fS) (MHz)

Power Dissipation (PD) (mW

)

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 10 of 17

AVDD3=3.3V, AVDD2=OVDD2 =1.8V, TAMBIENT (TA)=25°C, fSAMPLE=275MHz, VIN = 6.865MHz @ -0.5dBFS unless noted.

Figure 9. SFDR vs. fSAMPLE Figure 10. Differential Nonlinearity vs. Output Code

Figure 11. Integral Nonlinearity vs. Output Code Figure 12. Noise Histogram

Figure 13. Output Spectrum at 6.865MHz Figure 14. Output Spectrum at 68.465MHz

50 75 100 125 150 175 200 225 250 275 300

SAMPLE

(MHz)

SFDR (dBc

)

032 64 96 128 160 192 224 255

-0.25

-0.2

-0.15

-0.1

-0.05

0.05

0.1

0.15

0.2

0.25

code

DNL (LSBs)

032 64 96 128 160 192 224 255

-0.25

-0.2

-0.15

-0.1

-0.05

0.05

0.1

0.15

0.2

0.25

code

INL (LSBs)

126 127 128 129

5,000

10,000

15,000

20,000

25,000

30,000

35,000

40,000

45,000

50,000

code

Counts

020 40 60 80 100 120

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

Fre

uenc

(

MHz

)

Amplitude (dB)

Vin = -0.25dBFS

SNR = 49.2dB

SFDR = 71.0dBc

SINAD = 49.0dB

HD2 = -83dBc

HD3 = -66dBc

020 40 60 80 100 120

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

Frequency (MHz)

Amplitude (dB)

Vin = -0.22dBFS

SNR = 49.0dB

SFDR = 69.2dBc

SINAD = 49.0dB

HD2 = -77dBc

HD3 = -69dBc

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 11 of 17

AVDD3=3.3V, AVDD2=OVDD2 =1.8V, TAMBIENT (TA)=25°C, fSAMPLE=275MHz unless noted.

Figure 15. Output Spectrum at 130.565MHz Figure 16. Output Spectrum at 143.155MHz

Figure 17. Output Spectrum at 492.965MHz

020 40 60 80 100 120

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

Frequency (MHz)

Amplitude (dB)

Vin = -0.27

SNR = 49.1dB

SFDR = 66.8dBc

SINAD = 48.8dB

HD2 = -85dBc

HD3 = -68dBc

020 40 60 80 100 120

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

Frequency (MHz)

Amplitude (dB

)

Vin = -0.26dBFS

SNR = 49.1dB

SFDR = 70.3dBc

SINAD = 48.9dB

HD2 = -79dBc

HD3 = -69dBc

020 40 60 80 100 120

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

Frequency (MHz)

Amplitude (dB)

Vin = -0.25dBFS

SNR = 48.5dB

SFDR = 58.2dBc

SINAD = 47.8dB

HD2 = -58dBc

HD3 = -61dBc

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 12 of 17

Functional Description

The KAD2708 is based upon a eight bit, 275MSPS A/D

converter in a pipelined architecture. The input volt-

age is captured by a sample & hold circuit and con-

verted to a unit of charge. Proprietary charge do-

main techniques are used to compare the input to a

series of reference charges. These comparisons de-

termine the digital code for each input value. The

converter pipeline requires 24 sample clocks to pro-

duce a result. Digital error correction is also applied,

resulting in a total latency of 28 clock cycles. This is

evident to the user as a latency between the start of

a conversion and the data being available on the

digital outputs.

At start-up, a self-calibration is performed to minimize

gain and offset errors. The reset pin (RST) is initially

held low internally at power-up and will remain in

that state until the calibration is complete. The clock

frequency should remain fixed during this time.

Calibration accuracy is maintained for the sample

rate at which it is performed, and therefore should be

repeated if the clock frequency is changed by more

than 10%. Recalibration can be initiated via the RST

pin, or power cycling, at any time.

Reset

The KAD2708C resets and calibrates automatically on

power-up. To force a reset and initiate recalibration

of the ADC after power-up, connect an open-drain

output device to drive pin 28 (RST) and pull low for at

least ten sample clock periods. Do not use a device

with a pull-up on the reset pin, as it may prevent the

KAD2708 from properly executing the power-on reset.

Voltage Reference

The VREF pin is the full-scale reference, which sets the

full-scale input voltage for the chip and requires a

bypass capacitor of 0.1uF or larger. An internally

generated reference voltage is provided from a

bandgap voltage buffer. This buffer can sink or

source up to 50µA externally.

An external voltage may be applied to this pin to

provide a more accurate reference than the inter-

nally generated bandgap voltage or to match the

full-scale reference among a system of KAD2708C

chips. One option in the latter configuration is to use

one KAD2708C's internally generated reference as

the external reference voltage for the other chips in

the system. Additionally, an externally provided refer-

ence can be changed from the nominal value to

adjust the full-scale input voltage within a limited

range.

To select whether the full-scale reference is internally

generated or externally provided, the digital input

port VREFSEL should be set appropriately, low for in-

ternal or high for external. This pin also has an internal

18k pull-up resistor. To use the internally generated

reference VREFSEL can be tied directly to AVSS, and

to use an external reference VREFSEL can be allowed

to float.

Analog Input

The fully differential ADC input (INP/INN) connects to

the sample and hold circuit. The ideal full-scale input

voltage is 1.5VPP, centered at the VCM voltage of

0.86V as shown in Figure 18.

Figure 18. Analog Input Range

Best performance is obtained when the analog in-

puts are driven differentially in an ac-coupled con-

figuration. The common mode output voltage, VCM,

should be used to properly bias each input as shown

in Figures 19 and 20. An RF transformer will give the

best noise and distortion performance for wideband

and/or high intermediate frequency (IF) inputs. The

recommended biasing is shown in Figure 19.

Figure 19. Transformer Input

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 13 of 17

The value of the termination resistor should be deter-

mined based on the desired impedance. The differ-

ential input impedance of the KAD2708 is 10M.

A differential amplifier can be used in applications

that require dc coupling, at the expense of reduced

dynamic performance. In this configuration the am-

plifier will typically reduce the achievable SNR and

distortion performance. A typical differential amplifier

configuration is shown in Figure 20.

Figure 20. Differential Amplifier Input

Clock Input

The clock input circuit is a differential pair (see Figure

24). Driving these inputs with a high level (up to 1.8VPP

on each input) sine or square wave will provide the

lowest jitter performance. The recommended drive

circuit is shown in Figure 21. The clock inputs can be

driven single-ended, but this is not recommended as

performance will suffer.

Figure 21. Recommended Clock drive

The CLKDIV pin is a 1.8V CMOS control pin (input)

that selects whether the input clock frequency is

passed directly to the ADC or divided by two. Apply-

ing a low level will divide by two; 1.8V applied (or left

floating) will not divide.

Use of the clock divider is optional. The KAD2708C's

ADC requires a clock with 50% duty cycle for opti-

mum performance. If such a clock is not available,

one option is to generate twice the desired sampling

rate, then use the KAD2708C's divide-by-2 to gener-

ate a 50%-duty-cycle clock. The divider only uses the

rising edge of the clock, so 50% clock duty cycle is

assured .

Table 3. CLKDIV Pin Settings

Jitter

In a sampled data system, clock jitter directly im-

pacts the achievable SNR performance. The theoreti-

cal relationship between clock jitter and maximum

SNR is shown in Equation 1 and is illustrated in Figure

22.

Where tj is the RMS uncertainty in the sampling instant.

Equation 1.

This relationship shows the SNR that would be

achieved if clock jitter were the only non-ideal fac-

tor. In reality, achievable SNR is limited by internal

factors such as differential nonlinearity, aperture jitter

and thermal noise.

Figure 22. SNR vs. Clock Jitter

Any internal aperture jitter combines with the input

clock jitter, in a root-sum-square fashion since they

are not statistically correlated, and this determines

the total jitter in the system. The total jitter, combined

with other noise sources, then determines the achiev-

able SNR.

CLKDIV Pin Divide Ratio

AVSS 2

AVDD 1

⎟

⎠

⎞

⎜

⎝

⎛

JIN tf

SNR

log20 10

tj=100ps

tj= 10p s

tj= 1p s

tj=0.1ps

10 Bits

12 Bits

14 Bits

100

1 10 100 1000

Input Frequency - MHz

SNR - dB

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 14 of 17

Equivalent Circuits

Figure 23. Analog Inputs

Figure 24. Clock Inputs

Figure 25. LVCMOS Outputs

Layout Considerations

Split Ground and Power Planes

Data converters operating at high sampling frequen-

cies require extra care in PC board layout. Many

complex board designs benefit from isolating the

analog and digital sections. Analog supply and

ground planes should be laid out under signal and

clock inputs. Locate the digital planes under outputs

and logic pins. Grounds should be joined under the

chip.

Clock Input Considerations

Use matched transmission lines to the inputs for the

analog input and clock signals. Locate transformers,

drivers and terminations as close to the chip as possi-

ble.

Bypass and Filtering

Bulk capacitors should have low equivalent series re-

sistance. Tantalum is a good choice. For best per-

formance, keep ceramic bypass capacitors very

close to device pins. Longer traces will increase in-

ductance, resulting in diminished dynamic perform-

ance and accuracy. Make sure that connections to

ground are direct and low impedance. Avoid form-

ing ground loops.

LVCMOS Outputs

Output traces and connections must be designed for

50 characteristic impedance.

Unused Inputs

Three of the four standard logic inputs (RESET, CLKDIV,

2SC) which will not be operated do not require con-

nection for best ADC performance. These inputs can

be left open if they are not used. VREFSEL must be

held low for internal reference, but can be left open

for external reference.

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 15 of 17

Definitions

Analog Input Bandwidth is the analog input fre-

quency at which the spectral output power at the

fundamental frequency (as determined by FFT analy-

sis) is reduced by 3dB from its full-scale low-frequency

value. This is also referred to as Full Power Bandwidth.

Aperture Delay or Sampling Delay is the time re-

quired after the rise of the clock input for the sam-

pling switch to open, at which time the signal is held

for conversion.

Aperture Jitter is the RMS variation in aperture delay

for a set of samples.

Clock Duty Cycle is the ratio of the time the clock

wave is at logic high to the total time of one clock

period.

Differential Non-Linearity (DNL) is the deviation of any

code width from an ideal 1 LSB step.

Effective Number of Bits (ENOB) is an alternate

method of specifying Signal to Noise-and-Distortion

Ratio (SINAD). In dB, it is calculated as: ENOB =

(SINAD-1.76) / 6.02.

Integral Non-Linearity (INL) is the deviation of each

individual code from a line drawn from negative full-

scale (1/2 LSB below the first code transition) through

positive full-scale (1/2 LSB above the last code transi-

tion). The deviation of any given code from this line is

measured from the center of that code.

Least Significant Bit (LSB) is the bit that has the small-

est value or weight in a digital word. Its value in terms

of input voltage is VFS/(2N-1) where N is the resolution

in bits.

Missing Codes are output codes that are skipped

and will never appear at the ADC output. These

codes cannot be reached with any input value.

Most Significant Bit (MSB) is the bit that has the largest

value or weight. Its value in terms of input voltage is

VFS/2.

Pipeline Delay is the number of clock cycles between

the initiation of a conversion and the appearance at

the output pins of the corresponding data.

Power Supply Rejection Ratio (PSRR) is the ratio of a

change in power supply voltage to the input voltage

necessary to negate the resultant change in output

code.

Signal to Noise-and-Distortion (SINAD) is the ratio of

the RMS signal amplitude to the RMS value of the sum

of all other spectral components below one half the

clock frequency, including harmonics but excluding

DC.

Signal-to-Noise Ratio (without Harmonics) is the ratio

of the RMS signal amplitude to the sum of all other

spectral components below one-half the sampling

frequency, excluding harmonics and DC.

Spurious-Free-Dynamic Range (SFDR) is the ratio of

the RMS signal amplitude to the RMS value of the

peak spurious spectral component. The peak spuri-

ous spectral component may or may not be a har-

monic.

Two-Tone SFDR is the ratio of the RMS value of either

input tone to the RMS value of the peak spurious

component. The peak spurious component may or

may not be an IMD product.

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 16 of 17

E1 E

D/2

D1/2

E1/2 E/2

0.80 DIA

PIN 1 ID

TERMINAL TIP

SECTION “C-C”

SCALE: NONE

TOP VIEW

SEATING

PLANE

4X P

0.45

0.25

MIN

E2/2

E2 16Xe

REF.

16Xe

REF.

0.25 MIN

BOTTOM VIEW

4X P

D2/2

Outline Dimensions

KAD2708C 8-Bit, 275MSPS Analog-to-Digital Converter

Rev 1.1 Page 17 of 17

Package Dimensions (mm)

Ordering Guide

This product is compliant with EU directive 2002/95/EC regarding the Restriction of Hazardous Sub-

stances (RoHS). Contact Kenet for a materials declaration for this product.

Ref Min Nom Max Note

A - 0.90 1.00

A1 0.00 0.01 0.05 Per JEDEC MO-220

b 0.18 0.23 0.30 Measured between 0.20 and 0.25mm from plated terminal tip

D 10.00 BSC

D1 9.75 BSC

D2 7.55 7.70 7.85

e 0.50 BSC

E 10.00 BSC

E1 9.75 BSC

E2 7.55 7.70 7.85

L 0.50 0.60 0.65

N 68 Total terminals

ND 17 Terminals in D (x) direction

NE 17 Terminals in E (y) direction

Θ 0 12’

P 0 0.42 0.60

Model Speed Package Temp. Range

KAD2708C-27Q68 275MSPS 68-QFN EP -40°C to +85°C

KAD2708C-21Q68 210MSPS 68-QFN EP -40°C to +85°C

KAD2710C-17Q68 170MSPS 68-QFN EP -40°C to +85°C

KAD2710C-10Q68 105MSPS 68-QFN EP -40°C to +85°C

RoHS