ORT4622BCN432-DB - LATTICE SEMICONDUCTOR

Data Sheet

July 2009

ORCA

ORT4622 Field-Programmable System Chip (FPSC)

Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Introduction

Lattice has developed a solution for designers who

need the many advantages of FPGA-based design

implementation, coupled with high-speed serial back-

plane data transfer. The 622 Mbits/s backplane trans-

ceiver offers a clockless, high-speed interface for

interdevice communication on a board or across a

backplane. The built-in clock recovery of the

ORT4622 allows for higher system performance,

easier-to-design clock domains in a multiboard sys-

tem, and fewer signals on the backplane. Network

designers will beneﬁt from the backplane transceiver

as a network termination device. The backplane

transceiver offers SONET scrambling/descrambling

of data and streamlined SONET framing, pointer

moving, and transport overhead handling, plus the

programmable logic to terminate the network into

proprietary systems. For non-SONET applications,

all SONET functionality is hidden from the user and

no prior networking knowledge is required.

Embedded Core Features

■

Implemented in an

ORCA

Series 3 FPGA array.

■

Allows wide range of applications for SONET net-

work termination application as well as generic data

moving for high-speed backplane data transfer.

■

No knowledge of SONET/SDH needed in generic

applications. Simply supply data, 78 MHz clock, and

a frame pulse.

■

High-speed interface (HSI) function for clock/data

recovery serial backplane data transfer without

external clocks.

■

HSI function uses Lattice’s proven 622 Mbits/s

serial interface core.

■

Four-channel HSI function provides 622 Mbits/s

serial interface per channel for a total chip band-

width of 2.5 Gbits/s (full duplex).

■

LVDS I/Os compliant with

EIA

*-644, support hot

insertion.

■

8:1 data multiplexing/demultiplexing for 77.76 MHz

byte-wide data processing in FPGA logic.

■

On-chip phase-lock loop (PLL) clock meets B jitter

tolerance speciﬁcation of ITU-T Recommendation

G.958 (0.6 UI

P-P

at 250 kHz).

■

Powerdown option of HSI receiver on a per-

channel basis.

■

Highly efﬁcient implementation with only 3% over-

head vs. 25% for 8B10B coding.

■

In-Band management and conﬁguration.

■

Streamlined pointer processor (pointer mover) for

8 kHz frame alignment to system clocks.

■

Built-in boundry scan (

IEEE

†

1149.1 JTAG).

■

FIFOs align incoming data across all four channels

for STS-48 (2.5 Gbits/s) operation (in quad STS-12

format).

■

1 + 1 protection supports STS-12/STS-48 redun-

dancy by either software or hardware control for

protection switching applications.

EIA

is a registered trademark of Electronic Industries Associa-

tion.

†

IEEE

is a registered trademark of The Institute of Electrical and

Electronics Engineers, Inc.

Table 1.

ORCA

ORT4622 Available FPGA Logic

‡The embedded core and interface are not included in the above gate counts. The usable gate count range from a logic-only gate count to

a gate count assuming 30% of the PFUs/SLICs being used as RAMs. The logic-only gate count includes each PFU/SLIC (counted as

108 gates per PFU/SLIC), including 12 gates pre-LUT/FF pair (eight per PFU), and 12 gates per SLC/FF pair (one per PFU). Each of the

four PIOs per PIC is counted as 16 gates (two FFs, fast-capture latch, output logic, CLK drivers, and I/O buffers). PFUs used as RAM are

counted at four gates per bit, with each PFU capable of implementing a 32 x 4 RAM (or 512 gates) per PFU.

Device

Usable

System

Gates

‡

Number of

LUTs

Number of

Registers

Max User

RAM

Max User

I/Os Array Size Number of

PFUs

ORT4622 60K—120K 4032 5304 64K 259 18 x 28 504

Table of Contents

Contents Page Contents Page

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Lattice Semiconductor 2

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Introduction ............................................................... 1

Embedded Core Features ......................................... 1

FPSC Highlights ........................................................ 3

Software Support ....................................................... 3

Description ................................................................ 4

What Is an FPSC? .............................................. 4

FPSC Overview .................................................. 4

FPSC Gate Counting .......................................... 4

FPGA/Embedded Core Interface ........................ 4

ispLEVER Development System ........................ 4

FPSC Design Kit ................................................. 5

FPGA Logic Overview ........................................ 5

PLC Logic ............................................................ 5

PIC Logic ............................................................ 6

System Features ................................................ 6

Routing ............................................................... 6

Configuration ...................................................... 6

More Series 3 Information .................................. 6

ORT4622 Overview ................................................... 7

Device Layout ..................................................... 7

Backplane Transceiver Interface ........................ 7

HSI Interface ....................................................... 9

STM Macrocell .................................................... 9

CPU Interface ..................................................... 9

FPGA Interface ................................................... 9

FPSC Configuration ............................................ 11

Generic Backplane Transceiver

Application ............................................................... 11

Backplane Transceiver Core Detailed Description .... 12

HSI Macro ........................................................... 12

STM Transmitter (FPGA -> Backplane) .............. 14

STM Receiver (Backplane -> FPGA) .................. 18

Powerdown Mode ............................................... 24

Redundancy and Protection Switching ............... 24

Memory Map ............................................................. 25

Definition of Register Types ............................... 25

Memory Map Overview ....................................... 26

Powerup Sequencing for ORT4622 Device .............. 34

FPGA Configuration Data Format ............................. 35

Using ispLEVER to Generate Configuration RAM

Data ................................................................. 35

FPGA Configuration Data Frame ....................... 35

Bit Stream Error Checking ........................................ 37

FPGA Configuration Modes ...................................... 37

Absolute Maximum Ratings ...................................... 38

Recommend Operating Conditions ........................... 38

Electrical Characteristics ........................................... 39

HSI Circuit Specifications .......................................... 40

Input Data ........................................................... 40

Jitter Tolerance ................................................... 40

Generated Output Jitter ...................................... 40

PLL ..................................................................... 40

Input Reference Clock ........................................ 40

Power Supply Decoupling LC Circuit .................. 41

LVDS I/O ................................................................... 42

LVDS Receiver Buffer Requirements ................. 43

Timing Characteristics ............................................... 44

Description .......................................................... 44

PFU Timing ......................................................... 45

PLC Timing ......................................................... 45

SLIC Timing ........................................................ 45

PIO Timing .......................................................... 45

Special Function Timing ..................................... 45

Clock Timing ....................................................... 45

Configuration Timing ........................................... 45

Readback Timing ................................................ 45

Input/Output Buffer Measurement Conditions

(on-LVDS Buffer) ...................................................... 55

FPGA Output Buffer Characteristics ......................... 56

LVDS Buffer Characteristics ...................................... 57

Termination Resistor ........................................... 57

LVDS Driver Buffer Capabilities .......................... 57

Estimating Power Dissipation .................................... 58

ORT4622 Clock Power ....................................... 58

Pin Information .......................................................... 59

Package Thermal Characteristics Summary ............. 74

JA ..................................................................... 74

JC ..................................................................... 74

JB ..................................................................... 74

FPGA Maximum Junction Temperature ............. 74

Package Thermal Characteristics ............................. 75

Package Coplanarity ................................................. 75

Package Parasitics .................................................... 75

Package Outline Diagrams ........................................ 77

Terms and Definitions ......................................... 77

432-Pin EBGA .................................................... 78

Ordering Information ................................................. 79

ORCA

ORT4622 FPSC

Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

3 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Embedded Core Features

(continued)

■

Pseudo-SONET protocol including A1/A2 framing.

■

SONET scrambling and descrambling for required

ones density (optional).

■

Selected transport overhead (TOH) bytes insertion

and extraction for interdevice communication via the

TOH serial link.

FPSC Highlights

■

Implemented as an embedded core in the

ORCA

Series 3+ FPSC architecture.

■

Allows the user to integrate the core with up to 120K

gates of programmable logic (all in one device) and

provides up to 242 user I/Os in addition to the

embedded core I/O pins.

■

FPGA portion retains all of the features of the

ORCA

Series 3 FPGA architecture:

— High-performance, cost-effective, 0.25 µm, 5-level

metal technology.

— Twin-quad programmable function unit (PFU)

architecture with eight 16-bit look-up tables

(LUTs) per PFU, organized in two nibbles for use

in nibble- or byte-wide functions. Allows for mixed

arithmetic and logic functions in a single PFU.

— Softwired LUTs (SWL) allow fast cascading of up

to three levels of LUT logic in a single PFU.

— Supplemental logic and interconnect cell (SLIC)

provides 3-statable buffers, up to 10-bit decoder,

and

PA L

*-like AND-OR-INVERT (AOI) in each

programmable logic cell (PLC).

— Up to three ExpressCLK inputs allow extremely

fast clocking of signals on- and off-chip plus

access to internal general clock routing.

— Dual-use microprocessor interface (MPI) can be

used for conﬁguration, as well as for a general-

purpose interface to the FPGA. Glueless interface

i960

†

and

PowerPC

‡

processors with user-

conﬁgurable address space provided.

— Programmable clock manager (PCM) adjusts

clock phase and duty cycle for input clock rates

from 5 MHz to 120 MHz. The PCM may be com-

bined with FPGA logic to create complex

functions, such as digital phase-locked loops,

frequency counters, and frequency synthesizers

or clock doublers. Two PCMs are provided per

device.

— True internal 3-state, bidirectional buses with

simple control provided by the SLIC.

— 32 x 4 RAM per PFU, conﬁgurable as single or

dual port. Create large, fast RAM/ROM blocks

(128 x 8 in only eight PFUs) using the SLIC

decoders as bank drivers.

— Built-in boundary scan (

IEEE

1149.1 JTAG) and

TS_ALL testability function to 3-state all I/O pins.

■

High-speed, on-chip interface provided between

FPGA logic and embedded core to reduce bottle-

necks typically found when interfacing off-chip.

Software Support

■

Supported by ispLEVER software and third-party

CAE tools for implementing

ORCA

Series 3+ devices

and simulation/timing analysis with the embedded

core functions.

■

Embedded core conﬁguration options and simulation

netlists generated by FPSC Conﬁguration Manager

utility.

PA L

is a trademark of Advanced Micro Devices, Inc.

†

i960

is a registered trademark of Intel Corporation.

‡

PowerPC

is a registered trademark of International Business

Machines Corporation.

Lattice Semiconductor 4

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Description

What Is an FPSC?

FPSCs, or ﬁeld-programmable system chips, are

devices that combine ﬁeld-programmable logic with

ASIC or mask-programmed logic on a single device.

FPSCs provide the time to market and ﬂexibility of

FPGAs, the design effort savings of using soft intellec-

tual property (IP) cores, and the speed, design density,

and economy of ASICs.

FPSC Overview

Lattice’s Series 3+ FPSCs are created from Series 3

ORCA

FPGAs. To create a Series 3+ FPSC, several

rows of programmable logic cells (see FPGA Logic

Overview section for FPGA logic details) are removed

from a Series 3

ORCA

FPGA, and the area is replaced

with an embedded logic core. Other than replacing

some FPGA gates with ASIC gates, at greater than

10:1 efﬁciency, none of the FPGA functionality is

changed—all of the Series 3 FPGA capability is

retained: MPI, PCMs, boundary scan, etc. The rows of

programmable logic are replaced at the bottom of the

device, allowing pins on the bottom and sides of the

replaced rows to be used as I/O pins for the embedded

core. The remainder of the device pins retain their

FPGA functionality as do special function FPGA pins

within the embedded core area.

FPSC Gate Counting

The total gate count for an FPSC is the sum of its

embedded core (standard-cell/ASIC gates) and its

FPGA gates. Because FPGA gates are generally

expressed as a usable range with a nominal value, the

total FPSC gate count is sometimes expressed in the

same manner. Standard-cell ASIC gates are, however,

10 to 25 times more silicon area efﬁcient than FPGA

gates. Therefore, an FPSC with an embedded function

is gate equivalent to an FPGA with a much larger gate

count.

FPGA/Embedded Core Interface

The interface between the FPGA logic and the embed-

ded core is designed to look like FPGA I/Os from the

FPGA side, simplifying interface signal routing and pro-

viding a uniﬁed approach with general FPGA design.

Effectively, the FPGA is designed as if signals were

going off of the device to the embedded core, but the

on-chip interface is much faster than going off-chip and

requires less power. All of the delays for the interface

are precharacterized and accounted for in ispLEVER

software.

Clock spines also can pass across the FPGA/embed-

ded core boundary. This allows for fast, low-skew clock-

ing between the FPGA and the embedded core. Many

of the special signals from the FPGA, such as DONE

and global set/reset, are also available to the embed-

ded core, making it possible to fully integrate the

embedded core with the FPGA as a system.

For even greater system ﬂexibility, FPGA conﬁguration

RAMs are available for use by the embedded core. This

allows for user-programmable options in the embedded

core, in turn allowing for greater ﬂexibility. Multiple

embedded core conﬁgurations may be designed into a

single device with user-programmable control over

which conﬁgurations are implemented, as well as the

capability to change core functionality simply by recon-

ﬁguring the device.

ispLEVER Development System

ispLEVER software is used to process a design from a

netlist to a conﬁgured FPSC. This system is used to

map a design onto the

ORCA

architecture and then

place and route it using ispLEVER software’s timing-

driven tools. The development system also includes

interfaces to, and libraries for, other popular CAE tools

for design entry, synthesis, simulation, and timing anal-

ysis.

The ispLEVER Development System interfaces to

front-end design entry tools and provides the tools to

produce a conﬁgured FPSC. In the design ﬂow, the

user deﬁnes the functionality of the FPGA portion of

the FPSC and embedded core settings at two points in

the design ﬂow: at design entry and at the bit stream

generation stage. Following design entry, the develop-

ment system’s map, place, and route tools translate the

netlist into a routed FPSC. A static timing analysis tool

is provided to determine device speed, and a back-

annotated netlist can be created to allow simulation.

ORCA

ORT4622 FPSC

Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

5 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Description

(continued)

Timing and simulation output ﬁles from ispLEVER are

also compatible with many third-party analysis tools. Its

bit stream generator is then used to generate the con-

ﬁguration data which is loaded into the FPSC’s internal

conﬁguration RAM.

When using the bit stream generator, the user selects

options that affect the functionality of the FPSC. Com-

bined with the front-end tools, ispLEVER produces

conﬁguration data that implements the various logic

and routing options discussed in this data sheet.

FPSC Design Kit

Development is facilitated by an FPSC design kit

which, together with ispLEVER and third-party synthe-

sis and simulation engines, provides all software and

documentation required to design and verify an FPSC

implementation. Included in the kit are the FPSC con-

ﬁguration manager, HDL gate-level structural netlists,

all necessary synthesis libraries, and complete online

documentation. The kit's software couples with

ispLEVER, providing a seamless FPSC design envi-

ronment. More information can be obtained by visiting

the

ORCA

website or contacting a local sales ofﬁce,

both listed on the last page of this document.

FPGA Logic Overview

ORCA

Series 3 FPGA logic is a new generation of

SRAM-based FPGA logic built on the successful

Series 2 FPGA line, with enhancements and innova-

tions geared toward today’s high-speed designs on a

single chip. Designed from the start to be synthesis

friendly and to reduce place and route times while

maintaining the complete routability of the

ORCA

Series 2 devices, the Series 3 more than doubles the

logic available in each logic block and incorporates sys-

tem-level features that can further reduce logic require-

ments and increase system speed.

ORCA

Series 3

devices contain many new patented enhancements

and are offered in a variety of packages, speed grades,

and temperature ranges.

ORCA

Series 3 FPGA logic consists of three basic ele-

ments: programmable logic cells (PLCs), programma-

ble input/output cells (PICs), and system-level features.

An array of PLCs is surrounded by PICs. Each PLC

contains a programmable function unit (PFU), a sup-

plemental logic and interconnect cell (SLIC), local rout-

ing resources, and conﬁguration RAM. Most of the

FPGA logic is performed in the PFU, but decoders,

PA L

-like functions, and 3-state buffering can be per-

formed in the SLIC. The PICs provide device inputs and

outputs and can be used to register signals and to per-

form input demultiplexing, output multiplexing, and

other functions on two output signals. Some of the sys-

tem-level functions include the new microprocessor

interface (MPI) and the programmable clock manager

(PCM).

PLC Logic

Each PFU within a PLC contains eight 4-input (16-bit)

look-up tables (LUTs), eight latches/ﬂip-ﬂops (FFs),

and one additional ﬂip-ﬂop that may be used indepen-

dently or with arithmetic functions.

The PFU is organized in a twin-quad fashion: two sets

of four LUTs and FFs that can be controlled indepen-

dently. LUTs may also be combined for use in arith-

metic functions using fast-carry chain logic in either

4-bit or 8-bit modes. The carry-out of either mode may

be registered in the ninth FF for pipelining. Each PFU

may also be conﬁgured as a synchronous 32 x 4

single- or dual-port RAM or ROM. The FFs (or latches)

may obtain input from LUT outputs or directly from

invertible PFU inputs, or they can be tied high or tied

low. The FFs also have programmable clock polarity,

clock enables, and local set/reset.

The SLIC is connected to PLC routing resources and to

the outputs of the PFU. It contains 3-state, bidirectional

buffers and logic to perform up to a 10-bit AND function

for decoding, or an AND-OR with optional INVERT

(AOI) to perform

PA L

-like functions. The 3-state drivers

in the SLIC and their direct connections to the PFU out-

puts make fast, true 3-state buses possible within the

FPGA logic, reducing required routing and allowing for

real-world system performance.

Lattice Semiconductor 6

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Description

(continued)

PIC Logic

The Series 3 PIC addresses the demand for ever-

increasing system clock speeds. Each PIC contains

four programmable inputs/outputs (PIOs) and routing

resources. On the input side, each PIO contains a fast-

capture latch that is clocked by an ExpressCLK. This

latch is followed by a latch/FF that is clocked by a sys-

tem clock from the internal general clock routing. The

combination provides for very low setup requirements

and zero hold times for signals coming on-chip. It may

also be used to demultiplex an input signal, such as a

multiplexed address/data signal, and register the sig-

nals without explicitly building a demultiplexer. Two

input signals are available to the PLC array from each

PIO, and the

ORCA

Series 2 capability to use any input

pin as a clock or other global input is maintained.

On the output side of each PIO, two outputs from the

PLC array can be routed to each output ﬂip-ﬂop, and

logic can be associated with each I/O pad. The output

logic associated with each pad allows for multiplexing

of output signals and other functions of two output sig-

nals.

The output FF, in combination with output signal multi-

plexing, is particularly useful for registering address

signals to be multiplexed with data, allowing a full clock

cycle for the data to propagate to the output. The I/O

buffer associated with each pad is the same as the

ORCA

Series 3 buffer.

System Features

The Series 3 also provides system-level functionality

by means of its dual-use microprocessor interface

(MPI) and its innovative programmable clock manager

(PCM). These functional blocks allow for easy glueless

system interfacing and the capability to adjust to vary-

ing conditions in today’s high-speed systems. Since

these and all other Series 3 features are available in

every Series 3+ FPSC, they can also interface to the

embedded core providing for easier system integration.

Routing

The abundant routing resources of

ORCA

Series 3

FPGA logic are organized to route signals individually

or as buses with related control signals. Clocks are

routed on a low-skew, high-speed distribution network

and may be sourced from PLC logic, externally from

any I/O pad, or from the very fast ExpressCLK pins.

ExpressCLKs may be glitchlessly and independently

enabled and disabled with a programmable control sig-

nal using the StopCLK feature. The improved PIC rout-

ing resources are now similar to the patented intra-PLC

routing resources and provide great ﬂexibility in moving

signals to and from the PIOs. This ﬂexibility translates

into an improved capability to route designs at the

required speeds when the I/O signals have been

locked to speciﬁc pins.

Conﬁguration

The FPGA logic’s functionality is determined by inter-

nal conﬁguration RAM. The FPGA logic’s internal ini-

tialization/conﬁguration circuitry loads the conﬁguration

data at powerup or under system control. The RAM is

loaded by using one of several conﬁguration modes,

including serial EEPROM, the microprocessor inter-

face, or the embedded function core.

More Series 3 Information

For more information on Series 3 FPGAs, please refer

to the Series 3 FPGA data sheet, available on the Lat-

tice website.

77 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

ORT4622 Overview

Device Layout

The ORT4622 FPSC provides a high-speed backplane

transceiver combined with FPGA logic. The device is

based on a 2.5 V 3.3 V I/O OR3L125B FPGA. The

OR3L125B has a 28 x 28 array of programmable logic

cells (PLCs). For the ORT4622, the bottom ten rows of

PLCs in the array were replaced with the embedded

backplane transceiver core. The ORT4622 embedded

core comprises the HSI macrocell, the synchronous

transport module (STM) macrocell, a CPU interface,

and LVDS I/Os. The four full-duplex channels perform

data transfer, scrambling/descrambling and framing at

the rate of 622 Mbits/s. Figure 1 shows the ORT4622

block diagram.

Table 2

shows a schematic view of the ORT4622. The

upper portion of the device is an 18 x 28 array of PLCs

surrounded on the left, top, and right by programmable

input/output cells (PICs). At the bottom of the PLC

array are the core interface cells (CICs) connecting to

the embedded core region. The embedded core region

contains the backplane transceiver functionality of the

device. It is surrounded on the left, bottom, and right by

backplane transceiver dedicated I/Os as well as power

and special function FPGA pins. Also shown are the

interquad routing blocks (hIQ, vIQ) present in the

Series 3 FPGA devices. System-level functions

(located in the corners of the PLC array), routing

resources, and conﬁguration RAM are not shown in

Table 2.

Backplane Transceiver Interface

The advantage of the ORT4622 FPSC is to bring spe-

ciﬁc networking functions to an early market presence

with programmable logic in FPGA system.

The 622 Mbits/s backplane transceiver core allows the

ORT4622 to communicate across a backplane or on a

given board at an aggregate speed of 2.5 Gbits/s, pro-

viding a physical medium for high-speed asynchronous

serial data transfer between system devices. This

device is intended for, but not limited to, connecting ter-

minal equipment in SONET/SDH and ATM systems.

For networking applications, the ORT4622 offers a

pseudo SONET framer and scrambler/descrambler

interface capable of frame synchronization and inser-

tion/extraction of selectable transport overhead bytes

and SONET scrambling and descrambling for four

STS-12 (622 Mbits/s) channels. The channels are syn-

chronized to each other by a user-provided 8 kHz

frame pulse. The ORT4622 also provides STS-48

(2.5 Gbits/s) operation across all four channels where

each channel is in STS-12 format. The pseudo-SONET

framer of OR4622 is designed with a reduced set of the

SONET framing algorithm. The pointer processing

capability is more suitable for low error rate intersystem

data communication, particular for backplane trans-

ceiver applications. Figure 2 shows the architecture of

the ORT4622 backplane transceiver core.

5-8113(F)

Figure 1. ORCA ORT4622 Block Diagram

• CLOCK/DATA

RECOVERY

4 FULL-

DUPLEX

SERIAL

CHANNELS

BYTE-

WIDE

DATA FPGA LOGIC

STANDARD

FPGA

I/Os

LVDS

622 Mbits/s

DATA

622 Mbits/s

DATA STM

• POINTER MOVER

• SCRAMBLING

• FIFO ALIGNMENT

• TOH PROCESSOR

I/Os

HSI

Lattice Semiconductor 8

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

ORT4622 Overview (continued)

Table 2. ORT4622 Array

IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII

PT1 PT2 PT3 PT4 PT5 PT6 PT7 PT8 PT9 PT10 PT11 PT12 PT13 PT14 PT15 PT16 PT17 PT18 PT19 PT20 PT21 PT22 PT23 PT24 PT25 PT26 PT27 PT28

IIII

PL1

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR1

IIII

PL2

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR2

IIII

PL3

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR3

IIII

PL4

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR4

IIII

PL5

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR5

IIII

PL6

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR6

IIII

PL7

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR7

IIII

PL8

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR8

IIII

PL9

C10

C11

C12

C13

C14

C15

C16

C17

C18

C19

C20

C21

C22

C23

C24

C25

C26

C27

C28

PR9

IIII

PL10

R10

C10

R10

C11

R10

C12

R10

C13

R10

C14

R10

C15

R10

C16

R10

C17

R10

C18

R10

C19

R10

C20

R10

C21

R10

C22

R10

C23

R10

C24

R10

C25

R10

C26

R10

C27

R10

C28

PR10

IIII

PL11

R11

C10

R11

C11

R11

C12

R11

C13

R11

C14

R11

C15

R11

C16

R11

C17

R11

C18

R11

C19

R11

C20

R11

C21

R11

C22

R11

C23

R11

C24

R11

C25

R11

C26

R11

C27

R11

C28

PR11

IIII

PL12

R12

C10

R12

C11

R12

C12

R12

C13

R12

C14

R12

C15

R12

C16

R12

C17

R12

C18

R12

C19

R12

C20

R12

C21

R12

C22

R12

C23

R12

C24

R12

C25

R12

C26

R12

C27

R12

C28

PR12

IIII

PL13

R13

C10

R13

C11

R13

C12

R13

C13

R13

C14

R13

C15

R13

C16

R13

C17

R13

C18

R13

C19

R13

C20

R13

C21

R13

C22

R13

C23

R13

C24

R13

C25

R13

C26

R13

C27

R13

C28

PR13

IIII

PL14

R14

C10

R14

C11

R14

C12

R14

C13

R14

C14

R14

C15

R14

C16

R14

C17

R14

C18

R14

C19

R14

C20

R14

C21

R14

C22

R14

C23

R14

C24

R14

C25

R14

C26

R14

C27

R14

C28

PR14

IIII

PL15

R15

C10

R15

C11

R15

C12

R15

C13

R15

C14

R15

C15

R15

C16

R15

C17

R15

C18

R15

C19

R15

C20

R15

C21

R15

C22

R15

C23

R15

C24

R15

C25

R15

C26

R15

C27

R15

C28

PR15

IIII

PL16

R16

C10

R16

C11

R16

C12

R16

C13

R16

C14

R16

C15

R16

C16

R16

C17

R16

C18

R16

C19

R16

C20

R16

C21

R16

C22

R16

C23

R16

C24

R16

C25

R16

C26

R16

C27

R16

C28

PR16

IIII

PL17

R17

C10

R17

C11

R17

C12

R17

C13

R17

C14

R17

C15

R17

C16

R17

C17

R17

C18

R17

C19

R17

C20

R17

C21

R17

C22

R17

C23

R17

C24

R17

C25

R17

C26

R17

C27

R17

C28

PR17

IIII

PL18

R18

C10

R18

C11

R18

C12

R18

C13

R18

C14

R18

C15

R18

C16

R18

C17

R18

C18

R18

C19

R18

C20

R18

C21

R18

C22

R18

C23

R18

C24

R18

C25

R18

C26

R18

C27

R18

C28

PR18

IIII

ASB1 ASB2 ASB3 ASB4 ASB5 ASB6 ASB7 ASB8 ASB9 ASB10 ASB11 ASB12 ASB13 ASB14 ASB15 ASB16 ASB17 ASB18 ASB19 ASB20 ASB21 ASB22 ASB23 ASB24 ASB25 ASB26 ASB27 ASB28

EMBEDDED CORE AREA

IIII

IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII IIII

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

9 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

ORT4622 Overview (continued)

HSI Interface

The high-speed interconnect (HSI) macrocell is used

for clock/data recovery and MUX/deMUX between

77.76 MHz byte-wide internal data buses and

622 Mbits/s external serial links.

The HSI interface receives four 622 Mbits/s serial input

data streams from the LVDS inputs and provides four

independent 77.76 MHz byte-wide data streams and

recovered clock to the STM macro. There is no require-

ment for bit alignment since SONET type framing will

take place inside the ORT4622 core. For transmit, the

HSI converts four byte-wide 77.76 MHz data streams

to serial streams at 622 Mbits/s at the LVDS outputs.

STM Macrocell

The STM portion of the embedded core consists of

transmitter (Tx) and receiver (Rx) sections. The

receiver receives four byte-wide data streams at

77.76 MHz and the associated clocks from the HSI. In

the Rx section, the incoming streams are SONET

framed and descrambled before they are written into a

FIFO which absorbs phase and delay variations and

allows the shift to the system clock. The TOH is then

extracted and sent out on the four serial ports. The

pointer Mover consists of three blocks: pointer inter-

preter, elastic store, and pointer generator. The pointer

interpreter ﬁnds the synchronous transport signal

(STS) synchronous payload envelopes (SPE) and

places it into a small elastic store from which the

pointer generator will produce four byte-wide STS-12

streams of data that are aligned to the system timing

pulse.

In the Tx section, transmitted data for each channel is

received through a parallel bus and a serial port from

the FPGA circuit. TOH bytes are received from the

serial input port and can be optionally inserted from

programmable registers or serial inputs to the STS-12

frame via the TOH processor. Each of the four parallel

input buses is synchronized to a free-running system

clock. Then the SPE and TOH data is transferred to the

HSI.

The STM macrocell also has a scrambler/descrambler

disable feature, allowing the user to disable the scram-

bler of the transmitter and the descrambler of the

receiver. Also, unused channels can be disabled to

reduce power dissipation.

CPU Interface

The embedded core has a dedicated, asynchronous,

MPC860 compatible, CPU interface that is used for de-

vice setup, control, and monitoring. Dual sets of I/O pins

of this CPU interface with a bit stream conﬁgurable

scheme provide designers a convenient and ﬂexible op-

tion for conﬁguration. One set of CPU I/O pins goes off

chip allowing direct connection with an onboard CPU.

Another set of CPU I/O pins is available to the FPGA

logic allowing for a stand-alone system free of an exter-

nal CPU interface, or for itegration into the Series 3

FPGA MPI interface.

The CPU interface is composed of an 8-bit data bus, a

7-bit address bus, a chip select signal, a read/write sig-

nal, and an interrupt signal.

FPGA Interface

The FPGA logic will receive/transmit frame-aligned

streams of 77.76 MHz data (maximum of four streams

in each direction) from/to the backplane transceiver

embedded core. All frames transmitted to the FPGA

will be aligned to the FPGA frame pulse which will be

provided by the FPGA user’s logic to the STM macro.

All frames received from the FPGA logic will be aligned

to the system frame pulse that will be supplied to the

STM macro from the FPGA user’s logic.

Lattice Semiconductor 10

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

ORT4622 Overview (continued)

5-8576 (F)

Figure 2. Architecture of ORT4622 Backplane Transceiver

TX TOH

PROCESSOR

FRAME

PROC.

TX CH A

(MACRO)

TX TOH

PROCESSOR

FRAME

PROC.

TX CH B

(MACRO)

TX TOH

PROCESSOR

FRAME

PROC.

TX CH D

(MACRO)

TX TOH

PROCESSOR

FRAME

PROC.

TX CH C

(MACRO)

LINE LBPK

(SOFT CTL)

TO RX TOH PROC.

QUAD CHANNEL

TRANSMITTER

PLL

RX CH A

(MACROCELL)

77.76

MHz

FIFO

POINTER

MOVER

STS48

CH A

RX CH B

(MACROCELL)

77.76

MHz

CH B

RX CH C

(MACROCELL)

77.76

MHz

CH C

RX CH D

(MACROCELL)

77.76

MHz

CH D

LVDS LPBK

(SOFT CTL)

SOFT CTL

DEVICE I/O

RX TOH

PROCESSOR

TOH CLK

QUAD CHANNEL

RECEIVER

CH A

CH B

SOFT CTL

CH C

CH D

SOFT CTL

TOH RX B

TOH RX C

TOH RX D

RX TOH FRAME

TOH CLK

TX TOH CLK EN

TOH TX A

TOH TX B

TX BUS A

TX BUS B

TOH TX C

TX BUS C

TOH TX D

TX BUS D

SYSTEM FRAME

LINE FRAME

PROT SWITCH A/B

DATA RX BUS A

DATA RX BUS B

PROT SWITCH C/D

DATA RX BUS C

DATA RX BUS D

LVDS

OUT A

LVDS

OUT B

LVDS

OUT C

LVDS

OUT D

LVDS

IN A

LVDS

IN B

LVDS

IN C

LVDS

IN D

FPGA I/F SIGNALS

CPU INTERFACE (ASYNC)

INT_N

DATA

ADDR

RD/WR_N

CS_N

RST_N

DEVICE I/O OR FPGA I/F SIGNALS (BIT STREAM SELECTABLE)

SOFT CTL

RX TOH CLK EN

622 MHz Clks

REF

FDBK

77.76

MHz

622 MHz

77.76

MHz

FRAME

CLOCK

TOH RX A

TOH_EN

SYSTEM CLOCK

(77.76 MHz)

SYSTEM CLOCK

RX TOH CLK FPEN

DATA RX D EN

DATA RX C EN

DATA RX B EN

DATA RX A EN

Lattice Semiconductor 11

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

ORT4622 Overview (continued)

FPSC Conﬁguration

Conﬁguration of the ORT4622 occurs in two stages,

FPGA bit stream conﬁguration and embedded core

setup.

FPGA Configuration

Prior to becoming operational, the FPGA goes through

a sequence of states, including powerup initialization,

conﬁguration, start-up, and operation. The FPGA logic

is conﬁgured by standard FPGA bit stream conﬁgura-

tion means as discussed in the Series 3 FPGA data

sheet. Additionally, for the ORT4622, the location of the

CPU interface to the embedded core, either on the

device pins or at the FPGA/embedded core boundary,

is conﬁgured via FPGA conﬁguration and is deﬁned via

the ORT4622 design kit. The default conﬁguration sets

the CPU interface pins to be active. A simple micropro-

cessor emulation soft Intellectual Property (IP) core

that uses very small FPGA logic is available from Lat-

tice. This microprocessor core sets up the embedded

core via a state machine and allows the ORT4622 to

work in an independent system without an external

microprocessor interface.

Embedded Core Setup

The embedded core operation is set up via the embed-

ded core CPU interface. All options for the operation of

the core are conﬁgured according to the device register

map presented in the detailed description section of

this data sheet.

During the powerup sequence, the ORT4622 device

(FPGA programmable circuit and the core) is held in

reset. All the LVDS output buffers and other output buff-

ers are held in 3-state. All ﬂip-ﬂops in core area are in

reset state, with the exception of the boundry scan shift

registers, which can only be reset by Boundary Scan

Reset. After powerup reset, the FPGA can start conﬁg-

uration. During FPGA conﬁguration, the ORT4622 core

will be held in reset and all the local bus interface sig-

nals are forced high, but the following active-high sig-

nals (PROT_SWITCH_A, PROT_SWITCH_C,

TX_TOH_CK_EN, SYS_FP, LINE_FP) are forced low.

The CORE_READY signal sent from the embedded

core to FPGA is held low, indicating core is not ready to

interact with FPGA logic. At the end of the FPGA con-

ﬁguration sequence, the CORE_READY signal will be

held low for six SYS_CLK cycles after DONE, TRI_IO

and RST_N (core global reset) are high. Then it will go

active-high, indicating the embedded core is ready to

function and interact with FPGA programmable circuit.

During FPGA reconﬁguration when DONE and TRI_IO

are low, the CORE_READY signal sent from the core to

FPGA will be held low again to indicate the embedded

core is not ready to interact with FPGA logic. During

FPGA partial conﬁguration, CORE_READY stays

active. The same FPGA conﬁguration sequence

described previously will repeat again.

The initialization of the embedded core consists of two

steps: register conﬁguration and synchronization of the

alignment FIFO. In order to conﬁgure the embedded

core, the registers need to be unlocked by writing 0xA0

to address 0x04 and writing 0x01 to address 0x05.

Control registers 0x04 and 0x05 are lock registers. If

the output bus of the data, serial TOH port, and TOH

clock and TOH frame pulse are controlled by 3-state

registers (the use of the registers for 3-state output

control is optional; these output 3-state enable signals

are brought across the local bus interface and available

to the FPGA side), the next step is to activate the 3-

state output bus and signals by taking them to func-

tional state from high-impedance state. This can be

done by writing 0x01 to correspond bits of the channel

registers 0x20, 0x38, 0x50, and 0x68. If the 3-state

control is done in FPGA logic or external logic instead

of in the embedded core registers, this step should be

done in that particular control logic also.

In addition, the synchronization of selected streams is

recommended for some networking systems applica-

tions. This is a resync of the alignment FIFO after the

enabled channels have a valid frame pulse. Here are

the procedures: Put all of the streams to be aligned,

including disabled streams, into their required align-

ment mode. Force AIS-L in all streams to be synchro-

nized (refer to register map, write 0x01 to DB1 of

Write a 0x01 to the FIFO alignment resync register, bit

DB1 of register 0x06. Wait four frames. Release the

AIS-L in all streams (write 1 to DB1 of register 0x20,

0x38, 0x50, 0x68). This procedures allows normal data

ﬂow through the embedded core.

1212 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Generic Backplane Transceiver

Application

The combination of ORT4622 and soft IP cores pro-

vides a generic data moving solution for non-SONET

applications. There is no requirement for SONET

knowledge to the users. All that is needed is to supply

the embedded core interface with data, clock, and a

8 kHz frame pulse. The provision registers may also

need to be set up, and this can be done through either

the FPGA MPI or in a state machine in the FPGA sec-

tion (VHDL code available from Lattice).

The 8 kHz frame pulse must be supplied to the

SYS_FP signal. For generic applications, the frame

pulse can be created in FPGA logic from the

77.76 MHz SYS_CLK using a simple resettable

counter (the frame pulse should only be high for one

cycle of the SYS_CLK). A VHDL core that automati-

cally provides the 8 kHz frame pulse is available from

Lattice. Byte-wide data is then sent to each of the

transmit channels as follows: the ﬁrst 36 bytes trans-

ferred will be invalid data (replaced by overhead),

where the ﬁrst byte is sent on the rising edge of

SYS_CLK when SYS_FP is high. The next 1044 byte

positions can be ﬁlled with valid data. This will repeat a

total of nine times (36 invalid bytes followed by 1044

valid bytes) at which time the next 8 kHz frame pulse

will be found. Thus, 87 out of 90 (96.7%) of the data

bytes sent are valid user data.

On the receive side, an 8 kHz pulse must again be sup-

plied to SYS_FP. In this case, however, only the signal

DATA_RX*_SPE must be monitored for each channel,

where a high value on this signal means valid data.

Again 87 out 90 bytes received (96.7%) will be valid

data.

In order to provide an easy user interface to transfer

arbitrary data streams through the ORT4622, Lattice

provides a soft Intellectual Property (IP) core called the

protocol independent framer, or PI-Framer. This block

transfers user format to the one described above and

allows for smoothing/rate transfer of this user data. This

framer works with a single channel at 622 Mbits/s, two

channels at 1.25 Gbits/s, or across four channels at 2.5

Gbits/s.

Backplane Transceiver Core Detailed

Description

HSI Macro

The high-speed interface (HSI) provides a physical

medium for high-speed asynchronous serial data trans-

fer between the ORT4622 and other devices. The

devices can be mounted on the same board or

mounted on different boards and connected through

the shelf backplane. The 622 Mbits/s CDR macro is a

four-channel clock phase select (CPS) and data retime

function with serial-to-parallel demultiplexing for the

incoming data stream and parallel-to-serial multiplexing

for outgoing data. The HSI macro consists of three

functionally independent blocks: receiver, transmitter,

and PLL synthesizer as shown in Figure 3.

The PLL synthesizer block receives a 77.76 MHz refer-

ence clock at its input, and provides a phase-locked

622.08 MHz clock to the transmitter block and phase

control signal to the receiver block. The PLL synthe-

sizer block is a common asset shared by four receive

and transmit channels.

The HSI receiver receives four channels of differential

622.08 Mbits/s serial data without clock at its LVDS

receive inputs. The received data must be scrambled,

conforming to SONET STS-12 and SDH STM-4 data

formats using either a PN7 or PN9 sequence. The PN7

characteristic polynomial is 1 + x6 + x7, and PN9 char-

acteristic polynomial is 1 + x4 + x9. The ORT4622 sup-

plies a default scrambler using the PN7 sequence. The

clock phase select and data retime (CPS/DR) module

performs a clock recovery and data retiming function by

using phase control information. The resultant

622.08 Mbits/s data and clock are then passed to the

deserializer module, which performs serial-to-parallel

conversion and provides a 77.76 Mbits/s parallel data

and clock at its output.

The HSI transmitter receives four channels of

77.76 Mbits/s parallel data that is synchronous to the

reference clock at its inputs. The serializer performs a

parallel-to-serial conversion using a 622.08 MHz clock

provided by the PLL/synthesizer block. The

622 Mbits/s serial data streams are then transmitted

through the LVDS drivers.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

13 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed Description (continued)

5-8592 (F)

Figure 3. HSI Functional Block Diagram

622.08 MHz

PLL

SYNTHESIZER

50 Ω

LOOPBKEN

CLOCK/DATA

ALIGNMENT

PHASE

ADJUSTMENT

DEMUX

622 Mbits/s SERIAL TO

78 MHz PARALLEL

LOOP-

BACK

HSI_RX

622 Mbits/s

DATA

622 MHz

CLOCK

MUX

78 MHz PARALLEL

TO 622 Mbits/s SERIAL

BS-MUX

100 Ω

LOOP-

BACK

HDOUT

622 Mbits/s

622.08 MHz

CLOCK

HSI_TX

622 Mbits/s

DATA

(77.76 MHz REF CLOCK)

REF78

REXT

(RESISTOR)

622 Mbits/s

DATA

LVDS

BUFFER

(77.76 Mbytes DATA)

(77.76 Mbits/s

DATA)

(77.76 MHz

CLOCK)

77.76 MHz

77.76 Mbytes DATA

BSCANEN

HDIN

622 Mbits/s

LVDS

BUFFER

SELECT

BOUNDARY-

SCAN

CONTROL

Lattice Semiconductor 14

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed

Description (continued)

STM Transmitter (FPGA -> Backplane)

The STM has four STS-12 transmit channels which can

be treated as a single STS-48 channel. In general, the

transmitter circuit receives four byte-wide 77.76 MHz

data from the FPGA, which nominally represents four

STS-12 streams (A, B, C, and D). This data is synchro-

nized to the system (reference) clock, and an 8 kHz

system frame pulse from the FPGA logic. Transport

overhead bytes are then optionally inserted into these

streams, and the streams are forwarded to the HSI. All

byte timing pulses required to isolate individual over-

head bytes (e.g., A1, A2, B1, D1—D3, etc.) are gener-

ated internally based on the system frame pulse

(SYS_FP) received from the FPGA logic. All streams

operate byte-wide at 77.76 MHz in all modes. The TOH

processor operates from 25 MHz to 77.76 MHz and

supports the following TOH signals: A1 and A2 inser-

tion and optional corruption; H1, H2, and H3 pass

transparently; BIP-8 parity calculation (after scram-

bling) and B1 byte insertion and optional corruption

(before scrambling); optional K1 and K2 insert; optional

S1/M0 insert; optional E1/F1/E2 insert; optional section

data communication channel (DCC, D1—D3) and line

data communication channel (DCC, D4—D12) inser-

tion (for intercard communications channel); scram-

bling of outgoing data stream with optional scrambler

disabling; and optional stream disabling.

When the ORT4622 is used in nonnetworking applica-

tions as a generic high-speed backplane data mover,

the TOH serial ports are unused or can be used for

slow-speed off-channel communication between

devices.

Data received on the parallel bus is optionally scram-

bled and transferred to LVDS outputs.

Byte Ordering Information

The core supports quad STS-12 mode of operation on

the input/output ports. STS-48 is also supported when

received in quad STS-12 format. When operating in

quad STS-12 mode, each of the independent byte

streams carries an entire STS-12 within it. Figure 4

reveals the byte ordering of the individual STS-12

streams and for STS-48 operation. Note that the recov-

ered data will always continue to be in the same order

as transmitted.

5-8574 (F)

Figure 4. Byte Ordering of Input/Output Interface in STS-12 Mode

1, 12

2, 12

3, 12

4, 12

1, 9

2, 9

3, 9

4, 9

1, 6

2, 6

3, 6

4, 6

1, 3

2, 3

3, 3

4, 3

1, 11

2, 11

3, 11

4, 11

1, 8

2, 8

3, 8

4, 8

1, 5

2, 5

3, 5

4, 5

1, 2

2, 2

3, 2

4, 2

1, 10

2, 10

3, 10

4, 10

1, 7

2, 7

3, 7

4, 7

1, 4

2, 4

3, 4

4, 4

1, 1

2, 1

3, 1

4, 1

STS-12 A

STS-12 B

STS-12 C

STS-12 D

STS-12 A

STS-12 B

STS-12 C

STS-12 D

STS-48 IN QUAD STS-12 FORMAT

QUAD STS-12

Lattice Semiconductor 15

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Backplane Transceiver Core Detailed

Description (continued)

Transport Overhead for In Band Communication

The TOH byte can be used for In Band conﬁguration,

service, and management since it is carried along the

same channel as data. In ORT4622, In Band signaling

can be efﬁciently utilized, since the total cost of over-

head is only 3.3%.

Transport Overhead Insertion (Serial Link)

The TOH serial links are used to insert TOH bytes into

the transmit data. The transmit TOH data and

TOH_CLK_EN get retimed by TOH_CLK in order to

meet setup and hold speciﬁcations of the device.

The retimed TOH data is shifted into a 288-bit (36-byte

by 8-bit) shift register and then multiplexed as an 8-bit

bus to be inserted into the byte-wide data stream.

Insertion from these serial links or pass-through of TOH

from the byte-wide data is under software control.

Transport Overhead Byte Ordering

(FPGA to Backplane)

In the transparent mode, SPE and TOH data received

on parallel input bus is transferred, unaltered, to the

serial LVDS output. However, B1 byte of STS#1 is

always replaced with a new calculated value (the 11

bytes following B1 are replaced with all zeros). Also, A1

and A2 bytes of all STS-1s are always regenerated.

TOH serial port in not used in the transparent mode of

operation.

In the TOH insert mode, SPE bytes are transferred,

unaltered, from the input parallel bus to the serial LVDS

output. On the other hand, TOH bytes are received

from the serial input port and are inserted in the STS-

12 frame before being sent to the LVDS output.

Although all TOH bytes from the 12 STS-1s are trans-

ferred into the device from each serial port, not all of

them get inserted in the frame. There are three hard-

coded exceptions to the TOH byte insertion:

■Framing bytes (A1/A2 of all STS-1s) are not inserted

from the serial input bus. Instead, they can always be

regenerated.

■Parity byte (B1 of STS#1) is not inserted from the

serial input bus. Instead, it is always recalculated (the

11 bytes following B1 are replaced with all zeros).

■Pointer bytes (H1/H2/H3 of all STS-1s) are not

inserted from the serial input bus. Instead, they

always ﬂow transparently from parallel input to LVDS

output.

In addition to the above hard-coded exceptions, the

source of some TOH bytes can be further controlled by

software. When conﬁgured to be in pass-through

mode, the speciﬁc bytes must ﬂow transparently from

the parallel input. Note that blocks of 12 STS-1 bytes

forming an STS-12 are controlled as a whole. There

are 15 software controls per channel, as listed below:

■Source of K1 and K2 bytes of the 12 STS-1s

(24 bytes) is speciﬁed by a control bit (per channel

control).

■Source of S1 and M0 bytes of the 12 STS-1s

(24 bytes) is speciﬁed by a control bit (per channel

control).

■Source of E1, F1, E2 bytes of the STS-1s (36 bytes)

is speciﬁed by a control it (per channel control).

■Source of D1 bytes of the STS-1s (12 bytes) is spec-

iﬁed by a control bit (per channel control).

■Source of D2 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D3 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D4 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D5 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D6 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D7 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D8 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D9 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D10 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D11 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

■Source of D12 bytes of the 12 STS-1s (12 bytes) is

speciﬁed by a control bit (per channel control).

TOH reconstruction is dependent on the transmitter

mode of operation. In the transparent mode of opera-

tion, TOH bytes on LVDS output are as shown in Table

Lattice Semiconductor 16

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed Description (continued)

Table 3. Transmitter TOH on LVDS Output (Transparent Mode)

In the TOH Insert mode of operation, TOH bytes on LVDS output are shown in the following Table. This also shows

the order in which data is transferred to the serial TOH interface, starting with the must signiﬁcant bit of the ﬁrst A1

byte. The ﬁrst bit of the ﬁrst byte is replaced by an even parity check bit over all TOH bytes from the previous TOH

frame.

Table 4. Transmitter TOH on LVDS Output (TOH Insert Mode)

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2

B100000000000

Regenerated bytes.

Transparent bytes from parallel input port.

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2

B1 0 0 0 0 0 0 0 0 0 0 0 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 E1 F1 F1 F1 F1 F1 F1 F1 F1 F1 F1 F1 F1

D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D1 D2 D2 D2 D2 D2 D2 D2 D2 D2 D2 D2 D2 D3 D3 D3 D3 D3 D3 D3 D3 D3 D3 D3 D3

H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3

K1 K1 K1 K1 K1 K1 K1 K1 K1 K1 K1 K1 K2 K2 K2 K2 K2 K2 K2 K2 K2 K2 K2 K2

D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 D4 D5 D5 D5 D5 D5 D5 D5 D5 D5 D5 D5 D5 D6 D6 D6 D6 D6 D6 D6 D6 D6 D6 D6 D6

D7 D7 D7 D7 D7 D7 D7 D7 D7 D7 D7 D7 D8 D8 D8 D8 D8 D8 D8 D8 D8 D8 D8 D8 D9 D9 D9 D9 D9 D9 D9 D9 D9 D9 D9 D9

D10 D10 D10 D10 D10 D10 D10 D10 D10 D10 D10 D10 D11 D11 D11 D11 D11 D11 D11 D11 D11 D11 D11 D11 D12 D12 D12 D12 D12 D12 D12 D12 D12 D12 D12 D12

S1 S1 S1 S1 S1 S1 S1 S1 S1 S1 S1 S1 M0 M0 M0 M0 M0 M0 M0 M0 M0 M0 M0 M0 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2 E2

Regenerated bytes.

Inserted or transparent bytes. Blocks of 12 STS-1 bytes are controlled as a whole. There are 15 controls/channel: K1/K2, S1/M0, E1/F1/E2, D1, D2, D3, D4, D5, D6, D7, D8, D9, D10,

D11, D12.

Transparent bytes (from parallel input port).

Inserted bytes from TOH serial input port.

Lattice Semiconductor 17

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Backplane Transceiver Core Detailed

Description (continued)

A1/A2 Frame Insert and Testing

The A1 and A2 bytes provide a special framing pattern

that indicates where a STS-1 begins in a bit stream. All

12 A1 bytes of each STS-12 are set to 0xF6, and all 12

A2 bytes of the STS-12 are set to 0x28 when not over-

ridden with an user-speciﬁed value for testing.

A1/A2 testing (corruption) is controlled per stream by

the A1/A2 error insert register. When A1/A2 corruption

detection is set for a particular stream, the A1/A2 val-

ues in the corrupted A1/A2 value registers are sent for

the number of frames deﬁned in the corrupted A1/A2

frame count register. When the corrupted A1/A2 frame

count register is set to zero, A1/A2 corruption will con-

tinue until the A1/A2 error insert register is cleared.

On a per-device basis, the A1 and A2 byte values are

set, as well as the number of frames of corruption.

Then, to insert the speciﬁed A1/A2 values, each chan-

nel has an enable register. When the enable register is

set, the A1/A2 values are corrupted for the number

speciﬁed in the number of frames to corrupt. To insert

errors again, the per-channel fault insert register must

be cleared, and set again. Only the last A1 and the ﬁrst

A2 are corrupted.

B1 Calculation and Insertion

A bit interleaved parity –8 (BIP-8) error check set for

even parity over all the bits of an STS-1 frame. B1 is

deﬁned for the ﬁrst STS-1 in an STS-N only. The B1

calculation block computes a BIP-8 code, using even

parity over all bits of the previous STS-12 frame after

scrambling and is inserted in the B1 byte of the current

STS-12 frame before scrambling. Per-bit B1 corruption

is controlled by the force BIP-8 corruption register (reg-

ister address 0F). For any bit set in this register, the

corresponding bit in the calculated BIP-8 is inverted

before insertion into the B1 byte position. Each stream

has an independent fault insert register that enables

the inversion of the B1 bytes. B1 bytes in all other STS-

1s in the stream are ﬁlled with zeros.

Stream Disable

When disabled via the appropriate bit in the stream

enable register, the prescrambled data for a stream is

set to all ones, feeding the HSI. The HSI macro is pow-

ered down on a per-stream basis, as are its LVDS out-

puts.

Scrambler

The data stream is scrambled using a frame synchro-

nous scrambler of sequence length 127. The scram-

bling function can be disabled by software. The

generating polynomial for the scrambler is 1 + x6 + x7.

This polynomial conforms to the standard SONET

STS-12 data format. The scrambler is reset to 1111111

on the ﬁrst byte of the SPE (byte following the Z0 byte

in the twelfth STS-1). That byte and all subsequent

bytes to be scrambled are exclusive-ORed, with the

output from the byte-wise scrambler. The scrambler

runs continuously from that byte on throughout the

remainder of the frame. A1, A2, J0, and Z0 bytes are

not scrambled.

System Frame Pulse and Line Frame Pulse

System frame pulse (for transmitter) and line frame

pulse (for receiver) are generated in FPGA logic. A1/A2

framing is used on the link for locating the 8 kHz frame

location. All frames sent to the FPGA are aligned to the

FPGA frame pulse LINE_FP which is provided by the

FPGA to the STM macro. All frames sent from the

FPGA to the STM will be aligned to the frame pulse

SYS_FP that is supplied to the STM macro. In either

directions, system frame pulse and line frame pulse are

active for one system clock cycle, indicating the loca-

tion of A1 byte of STS#1. They are common to all four

channels.

1818 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Backplane Transceiver Core Detailed

Description (continued)

STM Receiver (Backplane -> FPGA)

The ORT4622 has four receiving channels that can be

treated as one STS-48 stream, or treated as indepen-

dent channels. Incoming data is received through

LVDS serial ports at the data rate of 622 Mbits/s. The

receiver can handle the data streams with frame off-

sets of up to ±12 bytes which would be due to timing

skews between cards and along backplane traces. The

received data streams are processed in the HSI and

the STM, and then passed through the CIC boundary

to the FPGA logic.

Framer Block

The framer block, in Figure 5, takes byte-wide data

from the HSI, and outputs a byte-aligned, byte-wide

data stream and 8 kHz sync pulse. The framer algo-

rithm determines the out-of-frame/in-frame status of

the incoming data and will cause interrupts on both an

errored frame and an out-of-frame (OOF) state. The

framer detects the A1/A2 framing pattern and gener-

ates the 8 kHz frame pulse. When the framer detects

OOF, it will generate an interrupt. Also, the framer

detects an errored frame and increments an A1/A2

frame error counter. The counter can be monitored by a

processor to compile performance status on the quality

of the backplane.

Because the ORT4622 is intended for use between it

and another ORT4622 or other devices via a back-

plane, there is only one errored frame state. Thus after

two transitions are missed, the state machine goes into

the OOF state and there is no severely errored frame

(SEF) or loss-of-frame (LOF) indication.

B1 Calculate and Descramble (Backplane -> FPGA)

Each Rx block receives byte-wide scrambled

77.76 MHz data and a frame sync from the framer.

Since each HSI is independently clocked, the Rx block

operates on individual streams. Timing signals required

to locate overhead bytes to be extracted are generated

internally based on the frame sync. The Rx block pro-

duces byte-wide (optionally) descrambled data and an

output frame sync for the alignment FIFO block.

The B1 calculation block computes a BIP-8 (Bit Inter-

leaved Parity 8-bits) code, using even parity over all

bits of the previous STS-12 frame before descrambling;

this value is checked against the B1 byte of the current

frame after descrambling. A per-stream B1 error

counter is incremented for each bit that is in error. The

error counter may be read via the CPU interface.

Descrambling. The streams are descrambled using a

frame synchronous descrambler of sequence length

127 with a generating polynomial of 1 + x6 + x7. The

A1/A2 framing bytes, the section trace byte (J0) and

the growth bytes (Z0) are not descrambled. The

descrambling function can be disabled by software.

AIS-L Insertion. Alarm indication signal (AIS) is a con-

tinuous stream of unframed 1s sent to alert down-

stream equipment that the near-end terminal has

failed, lost its signal source, or has been temporarily

taken out of service. If enabled in the AIS_L force regis-

ter, AIS-L is inserted into the received frame by writing

all ones for all bytes of the descrambled stream.

AIS-L Insertion on Out-of-Frame. If enabled via a

writing all ones for all bytes of the descrambled stream

when the framer indicates that an out-of-frame condi-

tion exists.

Internal Parity Generation

Even parity is generated on all data bytes and is routed

in parallel with the data to be checked before the pro-

tection switch MUX at the parallel output.

FIFO Alignment (Backplane -> FPGA)

The alignment FIFO allows the transfer of all data to

the system clock. The FIFO sync block (Figure 5)

allows the system to be conﬁgured to allow the frame

alignment of multiple slightly varying data streams. This

optional alignment ensures that matching STS-12

streams will arrive at the FPGA end in perfect data

sync. The frame alignment is conﬁgurable to allow for

the possibility of fully independent (i.e., total frame mis-

alignment) STS-12s.

Lattice Semiconductor 19

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Backplane Transceiver Core Detailed

Description (continued)

5-8577 (F)

Figure 5. Interconnect of Streams for FIFO

Alignment

The incoming data from the clock and data recovery

can be separated into four STS-12 channels (A, B, C,

and D). These streams can be frame aligned in the pat-

terns shown in Figure 6.

5-8575 (F)

Figure 6. Alignment of Four STS-12 Streams

There is also a provision to allow certain streams to be

disabled (i.e., not producing interrupts or affecting syn-

chronization). These streams can be enabled at a later

time without disrupting other streams.

The FIFO block consists of a 24 by 10-bit FIFO per link.

This FIFO is used to align up to ±154.3 ns of interlink

skew and to transfer to the system clock. The FIFO

sync circuit takes metastable hardened frame pulses

from the write control blocks and produces sync signals

that indicate when the read control blocks should begin

reading from the ﬁrst FIFO location. On top of the sync

signals, this block produces an error indicator which

indicates that the signals to be aligned are too far apart

for alignment (i.e., greater than 18 clocks apart). Sync

and error signals are sent to read control block for

alignment. The read control block is synched only once

on start-up; any further synchronization is software

controlled. The action of resynching a read control

block will always cause loss of data. A register allows

the read control block to be resynched.

Link Alignment. The general operation of the link

alignment algorithm is to wait 12 clocks (i.e., half the

FIFO) from the arriving frame pulse and then signal the

read control block to begin reading. For perfectly

aligned frame pulses across the links, it is simply a

matter of counting down 12 and then signaling the read

control block.

The algorithm down counts by one until all of the frame

pulses have arrived and then by two when they are all

present. For example (Figure 7), if all pulses arrive

together, then alignment algorithm would count 24

(12 clocks); if, however, the arriving pulses are spread

out over four clocks, then it would count one for the ﬁrst

four pulses and then two per clock afterward, which

gives a total of 14 clocks between ﬁrst frame pulse and

the ﬁrst read. This puts the center of arriving frame

pulses at the halfway point in the buffer. This is the

extent of the algorithm, and it has no facility for actively

correcting problems once they occur.

The write control block receives byte-wide data at

77.76 MHz and a frame pulse two clocks before the

ﬁrst A1 byte of the STS-12 frame. It generates the write

address for the FIFO block. The ﬁrst A1 in every STS-

12 stream is written in the same location (address 0) in

the FIFO. Also, a frame bit is passed through the FIFO

along with the ﬁrst byte before the ﬁrst A1 of the STS-

12. The read control block synchronizes the reading of

the FIFO for streams that are to be aligned. Reading

begins when the FIFO sync signals that all of the appli-

cable A1s and the appropriate margin have been writ-

ten to the FIFO. All of the read blocks to be

synchronized begin reading at the same time and

same location in memory (address 0).

The alignment algorithm takes the difference between

read address and write address to indicate the relative

clock alignments between STS-12 streams. If this

depth indication exceeds certain limits (12 clocks), then

an interrupt is given to the microprocessor (alignment

overﬂow). Each STS-12 stream can be realigned by

software if it gets too far out of line (this would cause a

loss of data). For background applications that have

less than 154.3 ns of interlink skew, misalignment will

not occur.

STS-12

STREAM A

STS-12

STREAM B

STS-12

STREAM C

STS-12

STREAM D

FIFO

SYNC

STREAM A

STREAM B

STREAM C

STREAM D

STREAM A

STREAM B

STREAM C

STREAM D

Lattice Semiconductor 20

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed Description (continued)

5-8584 (F)

Figure 7. Examples of Link Alignment

Pointer Mover Block (Backplane -> FPGA)

The pointer mover maps incoming frames to the line framing that is supplied by the FPGA logic. The K1/K2 bytes

and H1-SS bits are also passed through to the pointer generator so that the FPGA can receive them. The pointer

mover handles both concatenations inside the STS-12, and to other STS-12s inside the core.

The pointer mover block can correctly process any length of concatenation of STS frames (multiple of three) as

long as it begins on an STS-3 boundary (i.e., STS-1 number one, four, seven, ten, etc.) and is contained within the

smaller of STS-3, 12, or 48. See details in Table 5.

Table 5. Valid Starting Positions for an STS-Mc

STS-1

Number STS-3cSPE STS-6cSPE STS-9cSPE STS-12cSPE STS-15cSPE

STS-18c to

STS-48c

SPEs

1 YES YES YES YES YES YES

4 YES YES YES NO YES —

7 YES YES NO NO YES —

10 YES NO NO NO YES —

13 YES YES YES YES YES —

16 YES YES YES NO YES —

19 YES YES NO NO YES —

22 YES NO NO NO YES —

25 YES YES YES YES YES —

28 YES YES YES NO YES —

31 YES YES NO NO YES —

34 YES NO NO NO YES NO

37 YES YES YES YES NO NO

40 YES YES YES NO NO NO

43 YES YES NO NO NO NO

46 YES NO NO NO NO NO

Note: YES = STS-Mc SPE can start in that STS-1.

NO = STS-Mc SPE cannot start in that STS-1.

— = YES or NO, depending on the particular value of M.

24-byte

FIFO

24-byte

FIFO

ALL FPs

12 CLOCKS

SYNC. PULSEARRIVE

TOGETHER

(WRITING

BEGINS)

(READING

BEGINS)

SYNC. PULSE

(READING

BEGINS)

LAST FP

ARRIVES

4 CLOCKS

FIRST FP

ARRIVES

(WRITING

BEGINS)

10 CLOCKS

PERFECTLY ALIGNED FRAMES 4-byte SPREAD IN ARRIVING FRAMES

Lattice Semiconductor 21

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Backplane Transceiver Core Detailed

Description (continued)

Pointer Interpreter State Machine. The pointer inter-

preter’s highest priority is to maintain accurate data

ﬂow (i.e., valid SPE only) into the elastic store. This will

ensure that any errors in the pointer value will be cor-

rected by a standard, fully SONET compliant, pointer

interpreter without any data hits. This means that error

checking for increment, decrement, and new data ﬂag

(NDF) (i.e., eight of 10) is maintained in order to ensure

accurate data ﬂow. A single valid pointer (i.e., 0—782)

that differs from the current pointer will be ignored. Two

consecutive incoming valid pointers that differ from the

current pointer will cause a reset of the J1 location to

the latest pointer value (the generator will then produce

an NDF). This block is designed to handle single bit

errors without affecting data ﬂow or changing state.

The pointer interpreter has only three states (NORM,

AIS, and CONC). NORM state will begin whenever two

consecutive NORM pointers are received. If two con-

secutive NORM pointers are received that both differ

from the current offset, then the current offset will be

reset to the last received NORM pointer. When the

pointer interpreter changes its offset, it causes the

pointer generator to receive a J1 value in a new posi-

tion. When the pointer generator gets an unexpected

J1, it resets its offset value to the new location and

declares an NDF. The interpreter is only looking for two

consecutive pointers that are different from the current

value. These two consecutive NORM pointers do not

have to have the same value. For example, if the cur-

rent pointer is ten and a NORM pointer with offset of 15

and a second NORM pointer with offset of 25 are

received, then the interpreter will change the current

pointer to 25. The receipt of two consecutive CONC

pointers causes CONC state to be entered. Once in

this state, offset values from the head of the concate-

nation chain are used to determine the location of the

STS SPE for each STS in the chain. Two consecutive

AIS pointers cause the AIS state to occur. Any two con-

secutive normal or concatenation pointers will end this

AIS state. This state will cause the data leaving the

pointer generator to be overwritten with 0xFF.

5-8589 (F)

Figure 8. Pointer Mover State Machine

Pointer Generator. The pointer generator maps the

corresponding bytes into their appropriate location in

the outgoing byte stream. The generator also creates

offset pointers based on the location of the J1 byte as

indicated by the pointer interpreter. The generator will

signal NDFs when the interpreter signals that it is com-

ing out of AIS state. The pointer generator resets the

pointer value and generates NDF every time a byte

marked J1 is read from the elastic store that doesn’t

match the previous offset.

Increment and decrement signals from the pointer

interpreter are latched once per frame on either the F1

or E2 byte times (depending on collisions); this ensures

constant values during the H1 through H3 times. The

choice of which byte time to do the latching on is made

once when the relative frame phases (i.e., received and

system) are determined. This latch point is then stable

unless the relative framing changes and the received H

byte times collide with the system F1 or E2 times, in

which case the latch point would be switched to the col-

lision-free byte time.

There is no restriction on how many or how often incre-

ments and decrements are processed. Any received

increment or decrement is immediately passed to the

generator for implementation regardless of when the

last pointer adjustment was made. The responsibility

for meeting the SONET criteria for maximum frequency

of pointer adjustments is left to an upstream pointer

processor.

When the interpreter signals an AIS state, the genera-

tor will immediately begin sending out 0xFF in place of

data and H1, H2, H3. This will continue until the inter-

preter returns to NORM or CONC (pointer mover state

machine) states and a J1 byte is received.

NORM

CONC AIS

2 x CONC

2 x NORM

2 x AIS

2 x CONC

2 x AIS

Lattice Semiconductor 22

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed

Description (continued)

Transport Overhead Extraction

Transport overhead is extracted from the receive data

stream by the TOH extract block. The incoming data

gets loaded into a 36-byte shift register on the system

clock domain. This, in turn, is clocked onto the TOH

clock domain at the start of the SPE time, where it can

be clocked out.

During the SPE time, the receiver TOH frame pulse is

generated, RX_TOH_FP, which indicates the start of

the row of 36 TOH bytes. This pulse, along with the

receive TOH clock enable, RX_TOH_CK_EN, as well

as the TOH data, are all launched on the rising edge of

the TOH clock TOH_CLK.

TOH Byte Ordering (Backplane to FPGA)

The TOH processor is responsible for dropping all TOH

bytes of each channel through one of four correspond-

ing serial ports. The four TOH serial ports are synchro-

nized to the TOH clock (the same clock that is being

used by the serial ports on the transmitter side). This

free-running TOH clock is provided to the core by

external circuitry and operates at a minimum frequency

of 25 MHz and a maximum frequency of 77.76 MHz.

Data is transferred over serial links in a bursty fashion

as controlled by the Rx TOH clock enable signal, which

is generated by the ASIC and common to the four

channels. All TOH bytes of STS-12 streams are trans-

ferred over the appropriate serial link in the same order

in which they appear in a standard STS-12 frame. Data

transfer should be preformed on a row-by-row basis

such that internal data buffering needs is kept to a min-

imum. Data transfers on the serial links will be synchro-

nized relative to the Rx TOH frame signal.

Receiver TOH Reconstruction

Receiver TOH reconstruction on output parallel bus is

as shown in the following table.

Table 6. Receiver TOH (Output Parallel Bus)

On the TOH serial port, all TOH bytes are dropped as received on the LVDS input (MSB ﬁrst). The only exception is

the most signiﬁcant bit of byte A1 of STS#1, which is replaced with an even parity bit. This parity bit is calculated

over the previous TOH frame. Also, on AIS-L (either resulting from LOF or forced through software), all TOH bits are

forced to all ones with proper parity (parity we automatically ends up being set to 1 on AIS-L).

Special TOH Byte Functions

K1 and K2 Handling. The K1 and K2 bytes are used in automatic protection switch (APS) applications. K1 and K2

bytes can be optionally passed through the pointer mover under software control, or can be set to zero with the

other TOH bytes.

A1 and A2 Handling. As discussed previously, the A1 and A2 bytes are used for a framing header. A1 and A2

bytes are always regenerated and set to hexadecimal F6 and 28, respectively.

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 000000000000

000000000000000000000000000000000000

H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3

000000000000

K100000000000K200000000000

000000000000000000000000000000000000

Regenerated bytes.

Regenerated bytes (under pointer generator control-SS bits must be transparent-AIS-P must be supported).

Bytes taken from Elastic Store Buffer, on negative stuff opportunity-else, forced to all zeros.

Transparent or all zeros (K1/K2 are either taken from K1/K2 buffer or forced to all zeros-soft, control). In transparent mode, AIS-L must be supported.

All zero bytes.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

23 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed Description (continued)

SPE and C1J1 Outputs. These two signals for each channel are passed to the FPGA logic to allow a pointer pro-

cessor or other function to extract payload without interpreting the pointers. For the ORT4622, each frame has 12

STS-1s. In the SPE region, there are 12 J1 pulses for each STS-1s. There is one C1(J0, new SONET speciﬁca-

tions use J0 instead of C1 as section trace to identify each STS-1 in an STS-N) pulse in the TOH area for one

frame. Thus, there is a total of 12 J1 pulses and one C1(J0) pulse per frame. C1(J0) pulse is coincident with the J0

of STS1 #1. In each frame, the SPE ﬂag is active when the data stream is in SPE area. SPE behavior is dependent

on pointer movement and concatenation. Note that in the TOH area, H3 can also carry valid data. When valid SPE

data is carried in this H3 slot, SPE is high in this particular TOH time slot. In the SPE region, if there is no valid data

during any SPE column, the SPE signal will be set to low. SPE allow a pointer processor to extract payload without

interpreting the pointers. The SPE and C1J1 functionality are described in Table 7. For generic data operation, valid

data is available when SPE is 1 and the C1J1 signal is ignored.

Table 7. SPE and C1J1 Functionality

Note: The following rules are observed for generating SPE and C1J1 signals: on occurrence of AIS-P on any of the STS-1, there is no corre-

sponding J1 pulse. In case of concatenated payloads (up to STS48c), only the head STS-1 of the group has an associated J1 pulse.

C1J1 signal tracks any pointer movements. During a negative justiﬁcation event, SPE is set high during the H3 byte to indicate that pay-

load data is available. During a positive justiﬁcation event, SPE is set low during the positive stuff opportunity byte to indicate that payload

data is not available.

5-9330(F)

Notes: C1J1 signal behavior shown in this ﬁgure is just for illustration purposes: C1 pulse position must always be as shown; however, position

of J1 pulses vary based on path overhead location of each STS-1 within the STS-12 stream.

C1J1 signal must always be active during C1(J0) time slot of STS#1.

C1J1 signal must also be active during the twelve J1 time slots. However, C1J1 must not be active for any STS-1 for which AIS-P is gen-

erated. Also, on concatenated payloads, only the head of the group must have a J1 pulse.

Figure 9. SPE and C1J1 Functionality

SPE C1J1 Description

0 0 TOH information excluding C1(J0) of STS1 #1.

0 1 Position of C1(J0) of STS1 #1 (one per frame). Typically used to provide a

unique link identiﬁcation (256 possible unique links) to help ensure cards

are connected into the backplane correctly or cables are connected

correctly.

1 0 SPE information excluding the 12 J1 bytes.

1 1 Position of the 12 J1 bytes.

STS-12 TOH ROW # 1 SPE ROW # 1

A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A1 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 A2 J0 Z0 Z0 Z0 Z0 Z0 Z0 Z0 Z0 Z0 Z0 Z0

STS-12

SPE

C1J1

C1 PULSE J1 PULSE OF

3RD STS-1

1ST SPE BYTES OF THE

12 STS-1S

123456789101112

Lattice Semiconductor 24

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Backplane Transceiver Core Detailed Description (continued)

5-9331

Notes: SPE signal behavior shown in this ﬁgure is just for illustration purposes: SPE behavior is dependent on pointer movements and concate-

nation.

SPE signal must be high during negative stuff opportunity byte time slots (H3) for which valid data is carried (negative stufﬁng).

SPE signal must be low during positive stuff opportunity byte time slots for which there is no valid data (positive stufﬁng).

Figure 10. SPE Stuff Bytes

STS-12 TOH ROW # 4 SPE ROW # 4

H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H1 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H2 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3 H3

STS-12

SPE

POSITIVE STUFF

OPPORTUNITY BYTES

123456789101112

NEGATIVE STUFF

OPPORTUNITY BYTES

SPE SIGNAL SHOWS NEGATIVE STUFFING FOR 2ND STS-1,

AND POSITIVE STUFFING FOR 6TH STS-1

Powerdown Mode

Powerdown mode will be entered when the corre-

sponding channel is disabled. Channels can be inde-

pendently enabled or disabled under software control.

Parallel data bus output enable and TOH serial data

output enable signals are made available to the FPGA

logic. The HSI macrocell’s corresponding channel is

also powered down. The device will power up with all

four channels in powerdown mode.

In addition, an LVDS_EN pin has been added to control

the LVDS pins during boundary scan. During functional

operation, enabling/disabling LVDS buffers is controlled

by software registers. When in boundary scan mode,

LVDS_EN controls the enabling/disabling of LVDS buff-

ers instead of software registers. This LVDS_EN pin

should be pulled high on the board for functional opera-

tion, and pulled low during boundary scan.

Redundancy and Protection Switching

The ORT4622 supports STS-12/STS-48 redundancy

by either software or hardware control for protection

switching applications. For the transmitter mode, no

additional functionality is required for redundant opera-

tion. For receiving data, STS-12 data redundancy can

be implemented within the same device, while STS-48

and above data stream requires a pair of ORT4622

devices to support redundancy.

In STS-12 mode, the channel A receive data bus port is

used for both channel A and channel B. Similarly, the

channel C receive data bus port is used for both chan-

nel C and channel D. Channel B and channel D

become the redundant channels. The channel B and

channel D receive data bus ports are unused. Soft reg-

isters provide independent control to the protection

switching MUXes for both parallel data ports and serial

TOH data ports. When direct hardware control for pro-

tection switching is needed, external protection switch

pins are available for channels A and B, and also chan-

nels C and D. The external protection switch pins only

support parallel SPE/TOH data protection switching,

but not the serial TOH data.

In STS-48 mode, two independent devices are required

to work and protect for redundancy. Parallel and serial

port output pins on the FPGA side should be 3-stated

as the basis for supporting redundancy. The existing

local bus enable signals at the CIC can be used as 3-

state controls for FPGA data bus if needed, which can

be easily accessed by software control. Users can also

create their own protection switch 3-state enable sig-

nals either in FPGA logic or external to the device,

depending on the speciﬁc application.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

25 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map

Deﬁnition of Register Types

There are six structural register elements: sreg, creg, preg, iareg, isreg, and iereg. There are no mixed registers in

the chip. This means that all bits of a particular register (particular address) are structurally the same.

Table 8. Structural Register Elements

Registers Access and General Description

The memory map comprises three address blocks:

■Generic register block: ID, revision, scratch pad, lock, FIFO alignment, and reset registers.

■Device register block: control and status bits, common to the four channels.

■Channel register blocks: each of the four channels have an address block. The four address blocks have the

exact same structure with a constant address offset between channel register blocks.

All registers are write-protected by the lock register, except for the scratch pad register. The lock register is a 16-bit

read/write register. Write access is given to registers only when the key value 0xA001 is present in the lock register.

An error ﬂag will be set upon detecting a write access when write permission is denied. The default value is

0x0000.

After powerup reset or soft reset, unused register bits will be read as zeros. Unused address locations are also

read as zeros. Write only register bits will be read as zeros. The detailed information on register access and func-

tion are described on the tables, memory map, and memory map bit description.

Element Register Description

sreg Status Register A status register is read only, and, as the name implies, is used to convey the status

information of a particular element or function of the ORT4622 core. The reset value

of an sreg is really the reset value of the particular element or function that is being

read. In some cases, an sreg is really a ﬁxed value. An example of which is the ﬁxed

ID and revision registers.

creg Control Register A control register is read and writable memory element inside core control. The

value of a creg will always be the value written to it. Events inside the ORT4622 core

cannot effect creg value. The only exception is a soft reset, in which case the creg

will return to its default value. The control register have default values as deﬁned in

the default value column of Table 9.

preg Pulse Register Each element, or bit, of a pulse register is a control or event signal that is asserted

and then deasserted when a value of one is written to it. This means that each bit is

always of value 0 until it is written to, upon which it is pulsed to the value of one and

then returned to a value of 0. A pulse register will always have a read value of 0.

iareg Interrupt Alarm

Each bit of an interrupt alarm register is an event latch. When a particular event is

produced in the ORT4622 core, its occurrence is latched by its associated iareg bit.

To clear a particular iareg bit, a value of one must be written to it. In the ORT4622

core, all isreg reset values are 0.

isreg Interrupt Status

Each bit of an interrupt status register is physically the logical-OR function. It is a

consolidation of lower level interrupt alarms and/or isreg bits from other registers. A

direct result of the fact that each bit of the isreg is a logical-OR function means that it

will have a read value of one if any of the consolidation signals are of value one, and

will be of value 0 if and only if all consolidation signals are of value 0. In the

ORT4622 core, all isreg default values are 0.

ereg Interrupt Enable

Each bit of a status register or alarm register has an associated enable bit. If this bit

is set to value one, then the event is allowed to propagate to the next higher level of

consolidation. If this bit is set to zero, then the associated iareg or isreg bit can still

be asserted but an alarm will not propagate to the next higher level. An interrupt

enable bit is an interrupt mask bit when it is set to value 0.

Lattice Semiconductor 26

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Memory Map Overview

Table 9. Memory Map

Notes:

1.Generic register block.

2.Device register block-Rx.

3.Device register block-Tx.

ADDR

[6:0]

Reg.

Type DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Default

Value

(hex)

Notes

Generic Register Block

00 sreg ﬁxed rev [7:0] 01 1

01 sreg ﬁxed ID LSB [7:0] 01

02 sreg ﬁxed ID MSB [7:0] A0

03 creg scratch pad [7:0] 00

04 creg lockreg MSB [7:0] 00

05 creg lockreg LSB [7:0] 00

06 preg — — ————FIFO align-

ment com-

mand

global

reset

command

Device Register Block

08 creg — — — Rx TOH

frame

and

Rx TOH

clock

enable

control

ext prot

sw en

ext prot

function

STS-48

STS-12 sel

(unused in

ORT4622)

LVDS

lpbk

control

00 2

09 creg — — — — parallel

port out-

put MUX

select for

ch C

parallel

port out-

put MUX

select for

ch A

serial port

output

MUX

select for

ch C

serial port

output

MUX

select for

ch A

0a creg — — — FIFO aligner threshold value (min) [4:0] 02

0b creg — — — FIFO aligner threshold value (max) [4:0] 15

0c creg — scrambler/

descram-

bler

control

input/

output

parallel

bus par-

ity control

line loop-

back

control

number of consecutive A1/A2 errors to

generate [3:0]

60 3

0d creg A1 error insert value [7:0] 00

0e creg A2 error insert value [7:0] 00

0f creg transmitter B1 error insert mask [7:0] 00

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

27 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 9. Memory Map

Notes:

1.Generic register block.

2.Device register block-Rx.

3.Device register block-Tx.

4.Top-level interrupts.

5.Rx control.

6.Tx control signals.

7.Per STS#1 cos ﬂag.

* ADDR values delimited by a comma indicate the address for each of four channels, from channel A to D. For example, the register to Tx con-

trol signals has addresses of 20, 38, 50, and 68. This indicates that channel A Tx control signals are at address 20, control B Tx control sig-

nals are at address

ADDR

[6:0]

Reg.

Type DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Default

Value

(hex)

Notes

Device Register Block (continued)

10 isreg — — — per

device int

ch D

interrupt

ch C

interrupt

ch B

interrupt

ch A

interrupt

00 4

11 iereg — — — enable/mask register [4:0] 00

12 iareg — — — — — — write to

locked

error ﬂag

frame

offset

error ﬂag

13 iereg — — — — — — enable/mask

Channel Register Block

20, 38,

50, 68

creg Protec-

tion

switching

3-state

control of

TOH data

output

Protec-

tion

switching

3-state

control of

parallel

data out-

put

channel

enable/

disable

control

parallel

output

bus par-

ity err ins

cmd

Rx K1/K2

source

select

TOH

serial

output

port par

err ins

cmd

force ais-l

control

behavior

in LOF

01 5

21, 39,

51, 69

creg Tx mode

of opera-

tion

Tx E1 F1

E2 source

select

Tx S1 M0

source

select

Tx K1/K2

source

select

Tx D12

source

select

Tx D11

source

select

Tx D10

source

select

Tx D9

source

select

00 6

22, 3a,

52, 6a

creg Tx D8

source

select

Tx D7

source

select

Tx D6

source

select

Tx D5

source

select

Tx D4

source

select

Tx D3

source

select

Tx D2

source

select

Tx D1

source

select

23, 3b,

53, 6b

creg — — — — — — B1 error

insert

command

A1/A2

error ins

command

24, 3c,

54, 6c

sreg — — — — Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

NA 7

25, 3d,

55, 6d

sreg Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

Concatin-

dication

Lattice Semiconductor 28

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 9. Memory Map

Notes:

1. Generic register block.

2. Device register block-Rx.

3. Device register block-Tx.

4. Top-level interrupts.

5. Rx control.

6. Tx control signals.

7. Per STS#1 cos ﬂag.

8. Per channel interrupt.

9. Per STS-12 interrupt ﬂags.

10. Per STS-1interrupt ﬂags.

ADDR

[6:0]

Reg.

Type DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Default

Value

(hex)

Notes

Channel Register Block (continued)

26, 3e,

56, 6e

isreg — — — — — elastic

store

overﬂow

ﬂag

ais-p ﬂag per

STS-12

alarm ﬂag

00 8

27, 3f,

57, 6f

iereg — — — — — enable/mask register [2:0] 00

28, 40,

58, 70

iareg — — TOH

serial

input port

parity

error ﬂag

input

parallel

bus

parity

error ﬂag

LVDS link

B1 parity

error ﬂag

LOF ﬂag Receiver

internal

path

parity

error ﬂag

FIFO

aligner

threshold

error ﬂag

00 9

29,41,

59, 71

iereg — — enable/mask register [5:0] 00

2a, 42,

5a, 72

iareg — — — — AIS

interrupt

ﬂags 12

AIS

interrupt

ﬂag 9

AIS

interrupt

ﬂag 6

AIS

interrupt

ﬂags 3

00 10

2b, 43,

5b, 73

iareg AIS

interrupt

ﬂag 11

AIS

interrupt

ﬂag 8

AIS

interrupt

ﬂag 5

AIS

interrupt

ﬂag 2

AIS

interrupt

ﬂag 10

AIS

interrupt

ﬂag 7

AIS

interrupt

ﬂag 4

AIS

interrupt

ﬂag 1

2c, 44,

5c, 74

iereg — — — — enable/

mask AIS

interrupt

ﬂag 12

enable/

mask AIS

interrupt

ﬂag 9

enable/

mask AIS

interrupt

ﬂag 6

enable/

mask AIS

interrupt

ﬂag 3

2d, 45,

5d, 75

iereg enable/

mask AIS

interrupt

ﬂag 11

enable/

mask AIS

interrupt

ﬂag 8

enable/

mask AIS

interrupt

ﬂag 5

enable/

mask AIS

interrupt

ﬂag 2

enable/

mask AIS

interrupt

ﬂag 10

enable/

mask AIS

interrupt

ﬂag 7

enable/

mask AIS

interrupt

ﬂag 4

enable/

mask AIS

interrupt

ﬂag 1

2e, 46,

5e, 76

iareg — — — — ES

overﬂow

ﬂag 12

overﬂow

ﬂag 9

overﬂow

ﬂag 6

overﬂow

ﬂag 3

2929 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 9. Memory Map

Notes:

1. Generic register block.

2. Device register block-Rx.

3. Device register block-Tx.

4. Top-level interrupts.

5. Rx control.

6. Tx control signals.

7. Per STS#1 cos ﬂag.

8. Per channel interrupt.

9. Per STS-12 interrupt ﬂags.

10. Per STS-1interrupt ﬂags.

11. Binning.

ADDR

[6:0]

Reg.

Type DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0

Default

Value

(hex)

Notes

Channel Register Block (continued)

2f, 47,

5f, 77

iareg ES

overﬂow

ﬂag 11

overﬂow

ﬂag 8

overﬂow

ﬂag 5

overﬂow

ﬂag 2

overﬂow

ﬂag 10

overﬂow

ﬂag 7

overﬂow

ﬂag 4

overﬂow

ﬂag 1

00 10

30, 48,

60, 78

iereg — — — — enable/

mask ES

overﬂow

ﬂags

enable/

mask ES

overﬂow

ﬂag

enable/

mask ES

overﬂow

ﬂags

enable/

mask ES

overﬂow

ﬂags

31, 49,

61, 79

iereg enable/

mask ES

overﬂow

ﬂag 11

enable/

mask ES

overﬂow

ﬂag 8

enable/

mask ES

overﬂow

ﬂag 5

enable/

mask ES

overﬂow

ﬂag 2

enable/

mask ES

overﬂow

ﬂag 10

enable/

mask ES

overﬂow

ﬂag 7

enable/

mask ES

overﬂow

ﬂag 4

enable/

mask ES

overﬂow

ﬂag 1

32, 4a,

62, 7a

counter overﬂow LVDS link B1 parity error counter 00 11

33, 4b,

63, 7b

counter overﬂow LOF counter 00

34, 4c,

64, 7c

counter overﬂow A1/A2 frame error counter 00

Lattice Semiconductor 30

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 10. Memory Map Bit Descriptions

Bit/Register

Name(s)

Bit/

Location

(hex)

Type

Default

Value

(hex)

Description

Generic Register Block

ﬁxed rev [7:0]

ﬁxed ID LSB [7:0]

ﬁxed ID MSB [7:0]

00 [7:0]

01 [7:0]

02 [7:0]

sreg 01

—

scratch pad [7:0] 03 [7:0] creg 00 The scratch pad has no function and is not used anywhere in the

ORT4622 core. However, this register can be written to and read from.

lockreg MSB [7:0]

lockreg LSB [7:0]

04 [7:0]

05 [7:0]

creg 00

In order to write to registers in memory locations 06 to 7F, lockreg MSB

and lockreg LSB must be respectively set to the values of A0 and 01. If

the MSB and LSB lockreg values are not set to {A0, 01}, then any values

written to the registers in memory locations 06 to 7F will be ignored.

After reset (both hard and soft), the ORT4622 core is in a write locked

mode. The ORT4622 core needs to be unlocked before it can be written

to. Also note that the scratch pad register (03) can always be written to

since it is unaffected by write lock mode.

FIFO alignment

command

global reset

command

06 [0]

06 [1]

preg NA The FIFO alignment and global reset commands are both accessed via

the pulse register in memory address 06. The FIFO alignment command

is used to frame align the outputs of the four receive stm stream FIFOs.

The global reset command is a soft (software initiated) reset. Neverthe-

less, the global reset command will have the exact reset effect as a hard

(RST_N pin) reset.

Device Register Block

LVDS loopback con-

trol

08 [0] creg 0 0 No loopback.

1 LVDS loopback, transmit to receive on.

STS48 STS12 sel 08 [1] creg 0 This control signal is untracked in the ORT4622 core. It is a scratch bit,

and its value has no effect on the ORT4622 core.

ext prot sw en

ext prot sw func

08 [3:2] creg 0 ext

prot

ext

prot

func

Switching control master.

0 — MUX is controlled by software (one control bit per MUX).

Output buffer 3-state signals are controlled by software (one

control bit per channel).

1 0 MUX on parallel output bus of channel A is controlled by

Prot_Switch A/B pin (0-> channel A, 1-> channel B).

MUX on parallel output bus of channel C is controlled by

Prot_Switch C/D pin (0 -> channel C, 1-> channel D).

Output buffer 3-state signals are controlled by software (one

control bit per channel).

1 1 MUX is controlled by software (one control bit per MUX).

Output buffer 3-state signals on parallel output bus of chan-

nels A and B are controlled by Prot_Switch A/B pin (0->

buffers active, 1-> hi-z).

Output buffer 3-state signals on parallel output bus of chan-

nels C and D are controlled by Prot_Switch C/D pin (0 ->

buffers active, 1-> hi-z).

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

31 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 10. Memory Map Bit Descriptions

Bit/Register

Name(s)

Bit/

Location

(hex)

Type

Default

Value

(hex)

Description

Device Register Block (continued)

Rx TOH frame and

Rx TOH clock enable

08 [4] creg 0 0 toh_ck_fp_en = 0, can be used to 3-state rx_toh_ck_en and

rx_toh_fp signals.

1 Functional Mode.

serial output port A

MUX select

serial output port A

MUX select

parallel output port A

MUX select

parallel output port A

MUX select

09 [0]

09 [1]

09 [2]

09 [3]

creg 1

TOH Output MUX Select for Port A

0 TOH output port A is multiplexed to channel B.

1 TOH output port A is multiplexed to channel A.

TOH Output MUX Select for Port C

0 TOH output port C is multiplexed to channel D.

1 TOH output port C is multiplexed to channel C.

Parallel Port Output MUX Select for Port A

0 Parallel output data bus port A is multiplexed to channel B.

1 Parallel output data bus port A is multiplexed to channel A.

Parallel Port Output MUX Select for Port C

0 Parallel output data bus port C is multiplexed to channel D.

1 Parallel output data bus port C is multiplexed to channel C.

FIFO aligner thresh-

old value (min) [4:0]

FIFO aligner thresh-

old value (max) [4:0]

0A [4:0]

0B [4:0]

creg 02

These are the minimum and maximum thresholds values for the per

channel receive direction alignment FIFOs. If and when the minimum or

maximum threshold value is violated by a particular channel, then the

interrupt event FIFO aligner threshold error will be generated for that

channel and latched as a FIFO aligner threshold error ﬂag in the

respective per STS-12 interrupt alarm register.

The allowable range for minimum threshold values is 0 to 23.

The allowable range for maximum threshold values is 0 to 22.

Note that the minimal and maximum FIFO aligner threshold values

apply to all four channels.

number of consecu-

tive A1/A2 errors to

generate [3:0]

A1 error insert value

[7:0]

A2 error insert value

[7:0]

0C [3:0]

0D [7:0]

0E [7:0]

creg 00

These three-per-device control signals are used in conjunction with the

per-channel A1/A2 error insert command control bits to force A1/A2

errors in the transmit direction.

If a particular channel’s A1/A2 error insert command control bit is set to

the value one, then the A1 and A2 error insert values will be inserted

into that channels respective A1 and A2 bytes. The number of consecu-

tive frames to be corrupted is determined by the number of consecutive

A1, A2 errors to generate[3:0] control bits.

The error insertion is based on a rising edge detector. As such, the con-

trol must be set to value 0 before trying to initiate a second A1/A2 cor-

ruption.

line loopback control 0C [4] creg 0 0 No loopback.

1 Receive to transmit loopback on FPGA side.

input/output parallel

bus parity control

0C [5] creg 0 0 Even parity.

1 Odd parity.

Lattice Semiconductor 32

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 10. Memory Map Bit Descriptions

Bit/Register Name(s)Bit/ Register

Location (hex)

Type

Default

Value

(hex)

Description

Device Register Block (continued)

scrambler/

descrambler control

0C [6] creg 1 0 No receive direction descramble/transmit direction

scramble.

1 In receive direction, descramble channel after

SONET frame recovery.

In transmit direction scramble data just before paral-

lel-to-serial conversion.

transmit B1 error insert

mask [7:0]

0F [7:0] creg 00 0 No error insertion.

1 Invert corresponding bit in B1 byte.

channel A int

channel B int

channel C int

channel D int

per device int

enable/mask register

[4:0]

10 [0]

10 [1]

10 [2]

10 [3]

10 [4]

11 [4:0]

creg

iereg

Consolidation Interrupts

0 No interrupt.

Mask interrupt in enable/mask register.

1 Interrupt.

Enable interrupt in enable/mask register.

frame offset error ﬂag

write to locked register

error ﬂag

enable/mask register

[1:0]

12 [0]

12 [1]

13 [1:0]

iareg

iereg

If in the receive direction the phase offset between any

two channels exceeds 17 bytes, then a frame offset error

event will be issued. This condition is continuously moni-

tored.

If the ORT4622 core memory map has not been unlocked

(by writing A1 00 to the lock registers), and any address

other than the lockreg registers or scratch pad register is

written to, then a write to locked register event will be gen-

erated.

Channel Register Block (Channel A, Channel B, Channel C, Channel D)

Rx behavior in LOF 20, 38 50, 68 [0] — 1 Receive Behavior in LOF

0 When receive direction OOF occurs, do not insert

AIS-L.

1 When receive direction OOF occurs, insert AIS-L.

Force AIS-L control 20, 38, 50, 68 [1] 0 Force AIS-L Control

0 Do not force AIS-L.

1 Force AIS-L.

TOH serial output port

par err ins cmd

20, 38, 50, 68 [2] — 0 0 Do not insert a parity error.

1 Insert parity error in parity bit of receive TOH serial

output for as long as this bit is set.

Rx K1/K2 source

select

20, 38, 50, 68 [3] — 0 0 Set receive direction K1/K2 bytes to 0.

1 Pass receive direction K1/K2 though pointer mover.

parallel output bus par-

ity err ins cmd

20, 38, 50, 68 [4] — 0 0 Do not insert parity error.

1 Insert parity error in the parity bit of receive direction

parallel output bus for as long as this bit is set.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

33 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 10. Memory Map Bit Descriptions

* The error insertion is based on a rising edge detector. As such, the control must be set to value 0 before trying to initiate a second A1/A2

corruption.

† The error insertion is based on a rising edge detector. As such, the control must be set to value 0 before trying to initiate a second B1

corruption.

Bit/Register Name(s)Bit/ Register

Location (hex)

Type

Default

Value

(hex)

Description

Channel Register Block (Channel A, Channel B, Channel C, Channel D) (continued)

channel enable/disable control 20, 38, 50, 68 [5] creg 0 Channel Enable/Disable Control

0 Powerdown channel A/B/C/D CDR

and LVDS I/O can be used with

data_rx_en to 3-state output buses.

1 Functional mode.

Hi-z control of parallel output bus. 20, 38, 50, 68 [6] creg 0 To be used as 3-state control for pro-

tection switching on the FPGA data

output.

Hi-z control of TOH data output. 20 [7] creg 0 To be used as 3-state control for TOH

data output. Only channel A enable sig-

nal is brought out.

Tx mode of operation 21, 39, 51, 69 [7] creg 0 Transmit Mode of Operation

0 Insert TOH from serial ports.

1 Pass through all TOH.

Tx E1 F2 E2 source select

Tx S1 M0 source select

Tx K1 K2 source select

Tx D12—D9 source select

Tx D8—D1 source select

21, 39, 51, 69 [6]

21, 39, 51, 69 [5]

21, 39, 51, 69 [4]

21, 39, 51, 69 [3:0]

22, 3a, 52, 6a [7:0]

creg

4’h0

8’h00

Other Registers

0 Insert TOH from serial ports.

1 Pass through that particular TOH

byte.

A1/A2 error insert command 23, 3b, 53, 6b [0] creg 0 0 Do not insert error.*

1 Insert error for number of frames in

B1 error insert command 23, 3b, 53, 6b [1] creg 0 0 Do not insert error.†

1 Insert error for one frame in B1 bits

deﬁned by register hex 0F.†

concatindication 12, 9, 6, 3

concatindication 11, 8, 5, 2, 10, 7, 4, 1

24, 3c, 54, 6c [3:0]

25, 3d, 55, 6d [7:0]

sreg

The value one in any bit location indi-

cates that STS# is in CONCAT mode.

A 0 indicates that the STS is not in

CONCAT mode, or is the head of a

concat group.

per STS-12 alarm ﬂag

AIS-P ﬂag

elastic store overﬂow ﬂag

enable/mask register [2:0]

26, 3e, 56, 6e [0]

26, 3e, 56, 6e [1]

26, 3e, 56, 6e [2]

27, 3f, 57, 6f [2:0]

isreg

iereg

3’b000

These ﬂag register bits per STS-12

alarm ﬂag, AIS-P ﬂag, and elastic store

overﬂow ﬂag are the per-channel inter-

rupt status (consolidation) register.

FIFO aligner threshold error flag

receiver internal path parity error flag

LOF flag

LVDS link B1 parity error flag

input parallel bus parity error flag

TOH serial input port parity error flag

enable/mask register [5:0]

28, 40, 58, 70 [0]

28, 40, 58, 70 [1]

28, 40, 58, 70 [2]

28, 40, 58, 70 [3]

28, 40, 58, 70 [4]

28, 40, 58, 70 [5]

29, 41, 59, 71 [5:0]

iareg

6’h00

These are per the STS-12 alarm flags

with the corresponding enable/mask

AIS interrupt flags 12, 9, 6, 3

AIS interrupt flags 11, 8, 5, 2, 10, 7, 4, 1

enable/mask register 12, 9, 6, 3

enable/mask register 11, 8, 5, 2, 10, 7, 4, 1

2a, 42, 5a, 72 [3:0]

2b, 43, 5b, 73 [7:0]

2c, 44, 5c, 74 [3:0]

2d, 45, 5d, 75 [7:0]

iareg

iereg

4’h0

8’h00

4’h0

8’h00

These are the AIS-P alarm flags with

the corresponding enable/mask

Lattice Semiconductor 34

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Memory Map (continued)

Table 10. Memory Map Bit Descriptions

* The error insertion is based on a rising edge detector. As such, the control must be set to value 0 before trying to initiate a second A1/A2

corruption.

† The error insertion is based on a rising edge detector. As such, the control must be set to value 0 before trying to initiate a second B1

corruption.

Powerup Sequencing for ORT4622 Device

ORCA

Series ORT4622 device uses two power supplies: one to power the device I/Os and the ASIC core (VDD),

which is set to 3.3 V for 3.3 V operation and 5 V tolerance on input pins, and another supply for the internal FPGA

logic (VDD2), which is set to 2.5 V. It is understood that many users will derive the 2.5 V core logic supply from a 3.3

V power supply, so the following recommendations are made for the powerup sequence of the supplies and allow-

able delays between power supplies reaching stable voltages. In general, both the 3.3 V and the 2.5 V supplies

should ramp-up and become stable as close together in time as possible. There is no delay requirement if the VDD2

(2.5 V) supply becomes stable prior to the VDD (3.3 V) supply. There is a delay requirement imposed if the VDD sup-

ply becomes stable prior to the VDD2 supply. The requirement is that the VDD2 (2.5 V) supply transition from

0 V to 2.3 V within 15.7 ms if the VDD (3.3 V) supply is already stable at a minimum of 3.0 V. If the VDD supply has

not yet reached 3.0 V when the VDD2 supply has reached 2.3 V, then the requirement is that the VDD2 supply reach

a minimum of 2.3 V within 15.7 ms of when the VDD supply reaches 3.0 V. If the chosen power supplies cannot

meet this delay requirement, it is always possible to hold off conﬁguration of the FPGA by asserting INIT or PRGM

until the VDD2 supply has reached 2.3 V. This process eliminates any power supply sequencing issues.

Bit/Register Name(s)Bit/ Register

Location (hex)

Type

Default

Value

(hex)

Description

Channel Register Block (Channel A, Channel B, Channel C, Channel D) (continued)

ES overflow flags 12, 9, 6, 3

ES overflow flags 11, 8, 5, 2, 10, 7, 4, 1

enable/mask register 12, 9, 6, 3

enable/mask register 11, 8, 5, 2, 10, 7, 4, 1

2e, 46, 5e, 76 [7:0]

2f, 47, 5f, 77 [3:0]

30, 48, 60, 78 [7:0]

31, 49, 61, 79 [7:0]

— 4’h0

8’h00

4’h0

8’h00

These are the elastic store overflow

alarm flags.

LVDS link B1 parity error counter 32, 4a, 62, 7a [7:0] counter 8’h00 7-bit count + overflow-reset on read.

LOF counter 33, 4b, 63, 7b [7:0] counter 8’h00 7-bit count + overflow-reset on read.

A1/A2 frame error counter 34, 4c, 64, 7c [7:0] counter 8’h00 7-bit count + overflow-reset on read.

Lattice Semiconductor 35

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

FPGA Configuration Data Format

The ispLEVER development system interfaces with

front-end design entry tools and provides tools to pro-

duce a fully conﬁgured FPSC. This section discusses

using the ispLEVER development system to generate

conﬁguration RAM data and then provides the details

of the conﬁguration frame format.

Using ispLEVER to Generate Conﬁguration

RAM Data

The conﬁguration data bit stream deﬁnes the embed-

ded core conﬁguration, the FPGA logic functionality,

and the I/O conﬁguration and interconnection. The data

bit stream is generated by the ispLEVER development

tools. The bit stream created by the bit stream genera-

tion tool is a series of 1s and 0s used to write the FPSC

conﬁguration RAM. It can be loaded into the FPSC

using one of the conﬁguration modes discussed else-

where in this data sheet.

For FPSCs, the bit stream is prepared in two separate

steps in the design ﬂow. The conﬁguration options of

the embedded core are speciﬁed using

ORCA

ORT4622 Design Kit Software at the beginning of the

design process. This offers the designer a speciﬁc con-

ﬁguration to simulate and design the FPGA logic to.

Upon completion of the design, the bit stream genera-

tor combines the embedded core options and the

FPGA conﬁguration into a single bit stream for down-

load into the FPSC.

FPGA Conﬁguration Data Frame

Conﬁguration data can be presented to the FPSC in

two frame formats: autoincrement and explicit. A

detailed description of the frame formats is shown in

Figure 11, Figure 12, and Table 11. The two modes are

similar except that autoincrement mode uses assumed

address incrementation to reduce the bit stream size,

and explicit mode requires an address for each data

frame. In both cases, the header frame begins with a

series of 1s and a preamble of 0010, followed by a

24-bit length count ﬁeld representing the total number

of conﬁguration clocks needed to complete the loading

of the FPSC.

The mandatory ID frame contains data used to deter-

mine if the bit stream is being loaded to the correct type

ORCA

device (i.e., a bit stream generated for an

ORT4622 is being sent to an ORT4622). Error check-

ing is always enabled for Series 3+ devices, through

the use of an 8-bit checksum. One bit in the ID frame

also selects between the autoincrement and explicit

address modes for this load of the conﬁguration data.

A conﬁguration data frame follows the ID frame. A data

frame starts with a one-start bit pair and ends with

enough one-stop bits to reach a byte boundary. If using

autoincrement conﬁguration mode, subsequent data

frames can follow. If using explicit mode, one or more

address frames must follow each data frame, telling the

FPSC at what addresses the preceding data frame is

to be stored (each data frame can be sent to multiple

addresses).

Following all data and address frames is the postam-

ble. The format of the postamble is the same as an

address frame with the highest possible address value

with the checksum set to all ones.

Lattice Semiconductor 36

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

FPGA Conﬁguration Data Format (continued)

Figure 11. Serial Configuration Data Format Autoincrement Mode

Figure 12. Serial Configuration Data Format Explicit Mode

Note: For slave parallel mode, the byte containing the preamble must be 11110010. The number of leading header dummy bits must

be (n * 8) + 4, where n is any nonnegative integer and the number of trailing dummy bits must be (n * 8), where n is any positive

integer. The number of stop bits/frame for slave parallel mode must be (x * 8), where x is a positive integer. Note also that the bit

stream generator tool supplies a bit stream that is compatible with all conﬁguration modes, including slave parallel mode.

Table 11. Conﬁguration Frame Format and Contents

Header

11110010 Preamble.

24-bit Length Count Conﬁguration frame length.

11111111 Trailing header—8 bits.

ID Frame

0101 1111 1111 1111 ID frame header.

Conﬁguration Mode 00 = autoincrement, 01 = explicit.

Reserved [41:0] Reserved bits set to 0.

ID 20-bit part ID.

Checksum 8-bit checksum.

11111111 Eight stop bits (high) to separate frames.

Configuration

Data

Frame

(repeated for each

data frame)

01 Data frame header.

Data Bits Number of data bits depends upon device.

Alignment Bits = 0 String of 0 bits added to bit stream to make frame header, plus

data bits reach a byte boundary.

Checksum 8-bit checksum.

11111111 Eight stop bits (high) to separate frames.

Configuration

Address

Frame

00 Address frame header.

14 Address Bits 14-bit address of location to start data storage.

Checksum 8-bit checksum.

11111111 Eight stop bits (high) to separate frames.

Postamble

00 Postamble header.

11111111 111111 Dummy address.

1111111111111111 16 stop bits.

5-5759(F)

CONFIGURATION DATA CONFIGURATION DATA

10 01 01

PREAMBLE LENGTH ID FRAME CONFIGURATION CONFIGURATION POSTAMBLE

CONFIGURATION HEADER

00 00

COUNT DATA FRAME 1 DATA FRAME 2

5-5760(F)

PREAMBLE LENGTH ID FRAME CONFIGURATION CONFIGURATION POSTAMBLE

CONFIGURATION HEADER

ADDRESS ADDRESS

COUNT DATA FRAME 1 DATA FRAME 2 FRAME 2FRAME 1

CONFIGURATION DATA CONFIGURATION DATA

10 01 0100 0000

Lattice Semiconductor 37

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

FPGA Conﬁguration Data Format

(continued)

Bit Stream Error Checking

There are three different types of bit stream error

checking performed in the

ORCA

Series 3+ FPSCs:

ID frame, frame alignment, and CRC checking.

The ID data frame is sent to a dedicated location in the

FPSC. This ID frame contains a unique code for the

device for which it was generated. This device code is

compared to the internal code of the FPSC. Any differ-

ences are ﬂagged as an ID error. This frame is auto-

matically created by the bit stream generation program

in ispLEVER.

Each data and address frame in the FPSC begins with

a frame start pair of bits and ends with eight stop bits

set to 1. If any of the previous stop bits were a 0 when a

frame start pair is encountered, it is ﬂagged as a frame

alignment error.

Error checking is also done on the FPSC for each

frame by means of a checksum byte. If an error is

found on evaluation of the checksum byte, then a

checksum/parity error is ﬂagged.

When any of the three possible errors occur, the FPSC

is forced into an idle state, forcing INIT low. The FPSC

will remain in this state until either the RESET or PRGM

pins are asserted.

If using either of the MPI modes to conﬁgure the FPSC,

the speciﬁc type of bit stream error is written to one of

the MPI registers by the FPGA conﬁguration logic. The

PGRM bit of the MPI control register can also be used

to reset out of the error condition and restart conﬁgura-

tion.

FPGA Conﬁguration Modes

There are eight methods for conﬁguring the FPSC. Six

of the conﬁguration modes are selected on the M0, M1,

and M2 input and are shown in Table 12. A fourth input,

M3, is used to select the frequency of the internal oscil-

lator, which is the source for CCLK in some conﬁgura-

tion modes. The nominal frequencies of the internal

oscillator are 1.25 MHz and 10 MHz. The 1.25 MHz fre-

quency is selected when the M3 input is unconnected

or driven to a high state.

Note that the Master parallel mode of conﬁguration that

is available in the

ORCA

Series 3 FPGAs is not avail-

able in the ORT4622.

More information on the general FPGA modes of con-

ﬁguration can be found in the

ORCA

Series 3 data

sheet.

Table 12. Conﬁguration Modes

Motorola

is a registered trademark of Motorola, Inc.

†

Intel

is a registered trademark of Intel Corporation.

M2 M1 M0 CCLK Configuration

Mode Data

0 0 0 Output Master Serial Serial

0 0 1 Input Slave Parallel Parallel

0 1 0 Output Microprocessor:

Motorola

Pow-

erPC

Parallel

0 1 1 Output Microprocessor:

Intel

†

i960

Parallel

1 0 0 Reserved

1 0 1 Output Async Peripheral Parallel

1 1 0 Reserved

1 1 1 Input Slave Serial Serial

Lattice Semiconductor 38

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Absolute Maximum Ratings

Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are abso-

lute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess

of those given in the operations sections of this data sheet. Exposure to absolute maximum ratings for extended

periods can adversely affect device reliability.

The

ORCA

Series 3+ FPSCs include circuitry designed to protect the chips from damaging substrate injection cur-

rents and to prevent accumulations of static charge. Nevertheless, conventional precautions should be observed

during storage, handling, and use to avoid exposure to excessive electrical stress.

Table 13. Absolute Maximum Ratings

Recommend Operating Conditions

Table 14. Recommend Operating Conditions

Parameter Symbol Min Max Unit

Storage Temperature Tstg –65 150 °C

I/O Supply Voltage with Respect to Ground VDD — 4.2 V

Internal Supply Voltage VDD2 — 3.2

Input Signal with Respect to Ground

CMOS I/O

5 V Tolerant I/O

—

–0.5

VDD + 0.3

5.8

Signal Applied to High-impedance Output — –0.5 VDD + 0.3 V

Maximum Package Body Temperature — — 220 °C

Junction Temperature TJ–40 125 °C

ORT4622

Temperature Range (Ambient) I/O Supply Voltage (VDD) Internal Supply Voltage (VDD2)

0 °C to 70 °C 3.3 V ± 5% 2.5 V ± 5%

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

39 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Electrical Characteristics

Table 15. General Electrical Characteristics

ORT4622 Commercial: VDD = 3.3 V ± 5%, VDD2 = 2.5 V ± 5%, 0 °C < TA < 70 °C.

Table 16. Electrical Characteristics for FPGA I/O

ORT4622 Commercial: VDD = 3.3 V ± 5%, VDD2 = 2.5 V ± 5%, 0 °C < TA < 70 °C.

* The pull-up resistor will externally pull the pin to a level 1.0 V below VDD.

Symbol Parameter Test Conditions ORT4622 Unit

Min Max

IDDSB Standby Current (TA = 25 °C, VDD = 3.3 V, VDD2 = 2.5 V) internal oscillator

running, no output loads, inputs at VDD or GND

(after conﬁguration)

— 5.3 mA

IDDSB Standby Current (TA = 25 °C, VDD = 3.3 V, VDD2 = 2.5 V) internal oscillator

stopped, no output loads, inputs at VDD or GND

(after conﬁguration)

— 1.4 mA

VDR Data Retention Voltage TA = 25 °C 2.3 — V

IPP Powerup Current Power supply current at approximately 1 V, within a recom-

mended power supply ramp rate of 1 ms—200 ms

2.7 — mA

Parameter Symbol Test Conditions ORT4622 Unit

Min Max

Input Voltage:

High

Low

VIH

VIL

Input conﬁgured as CMOS

(clamped to VDD) 50% VDD

GND – 0.5

VDD + 0.3

30% VDD

Input Voltage:

High

Low

VIH

VIL

Input conﬁgured as 5 V tolerant

50% VDD

GND – 0.5

5.8

30% VDD

Output Voltage:

High

Low

VOH

VOL

VDD = min, IOH = 6 mA or 3 mA

VDD = min, IOL = 12 mA or 6 mA

2.4

—

0.4

Input Leakage Current ILVDD = max, VIN = VSS or VDD –10 10 µA

Input Capacitance CIN (TA = 25 °C, VDD = 3.3 V, VDD2 = 2.5 V)

test frequency = 1 MHz

—8pF

Output Capacitance COUT (TA = 25 °C, VDD = 3.3 V, VDD2 = 2.5 V)

test frequency = 1 MHz

—9pF

DONE Pull-up Resistor* RDONE — 100 — kΩ

M[3:0] Pull-up Resistors* RM— 100 — kΩ

I/O Pad Static Pull-up

Current*

IPU (VDD = 3.6 V,

VIN = VSS, TA = 0 °C)

14.4 50.9 µA

I/O Pad Static Pull-down

Current

IPD (VDD = 3.6 V,

VIN = VSS, TA = 0 °C)

26 103 µA

I/O Pad Pull-up Resistor* RPU VDD = all, VIN = VSS, TA = 0 °C 100 — kΩ

I/O Pad Pull-down Resistor RPD VDD = all, VIN = VDD, TA = 0 °C 50 — kΩ

Lattice Semiconductor 40

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Electrical Characteristics (continued)

Table 17. Electrical Characteristics for Embedded Core I/O Other than LVDS I/O

Note: All outputs are driving 35 pF, except CPU data bus pins which drive 100 pF. It is assumed that the TTL buffers from the

standard-cell library can handle the 100 pF load.

Symbol Parameter Min Max Unit

VIH Input High Voltage (TTL input) 2.0 5.5 V

VIL Input Low Voltages (TTL input) — 0.8 V

VOH Output High Voltage (TTL output) 2.4 — V

VOH Output Low Voltage (TTL output) — 0.4 V

HSI Circuit Specifications

Input Data

The 622 Mbits/s scrambled input data stream must

conform to SONET STS-12 and SDH STM-4 data for-

mat using either a PN7 or PN9 sequence. The PN7

characteristic is 1 + x6 + x7 and the PN9 characteristic

is 1 + x4 + x9. The ORT4622 supplies a default scram-

bler using the PN7 sequence. The longest allowable

stream of nontransitional 622 Mbits/s input data is 60

bits. This sequence should not occur more often than

once per minute. An input signal phase change of no

more than 100 ps is allowed over 200 ns time interval,

which translates to a frequency change of 500 ppm.

The signal eye opening must be greater than 0.4 UIp-p

(unit interval peak-to-peak), and the unit interval for

622 Mbits/s is 1.6075 ns.

Jitter Tolerance

The input jitter tolerance of the ORT4622 is shown in

Table 18.

Table 18. Jitter Tolerance

Generated Output Jitter

The generated output jitter is a maximum of 0.2 UIp-p

from 250 kHz to 5 MHz.

PLL

PLL requires an external 10 kΩ pull-down resistor.

Table 19. PLL

Input Reference Clock

Table 20. Input Reference Clock

Frequency UIp-p

250 kHz 0.6

25 kHz 6.0

2 kHz 60

Parameter Min Max Unit

Loop Bandwidth — 6 MHz

Jitter Peaking — 2 dB

Powerup Reset Duration 10 — µs

Lock Acquisition — 1 ms

Parameter Min Max

Frequency Deviation — ± 20 ppm

Frequency Change — 500 ppm

Phase Change in 200 ns — 100 ps

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

41 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

HSI Circuit Specifications (continued)

Power Supply Decoupling LC Circuit

The 622 MHz HSI macro contains both analog and digital circuitry. The data recovery function, for example, is

implemented as primarily a digital function, but it relies on a conventional analog phase-locked loop to provide its

622 MHz reference frequency. The internal analog phase-locked loop contains a voltage-controlled oscillator. This

circuit will be sensitive to digital noise generated from the rapid switching transients associated with internal logic

gates and parasitic inductive elements. Generated noise that contains frequency components beyond the band-

width of the internal phase-locked loop (about 3 MHz) will not be attenuated by the phase-locked loop and will

impact bit error rate directly. Thus, separate power supply pins are provided for these critical analog circuit ele-

ments.

Additional power supply ﬁltering in the form of a LC pi ﬁlter section will be used between the power supply source

and these device pins as shown in Figure 13. The corner frequency of the LC ﬁlter is chosen based on the power

supply switching frequency, which is between 100 kHz and 300 kHz in most applications.

Capacitors C1 and C2 are large electrolytic capacitors to provide the basic cutoff frequency of the LC ﬁlter. For

example, the cutoff frequency of the combination of these elements might fall between 5 kHz and 50 kHz. Capaci-

tor C3 is a smaller ceramic capacitor designed to provide a low-impedance path for a wide range of high-frequency

signals at the analog power supply pins of the device. The physical location of capacitor C3 must be as close to the

device lead as possible. Multiple instances of capacitors C3 can be used if necessary. The recommended ﬁlter for

the HSI macro is shown below: L = 4.7 μH, RL = 1 Ω, C1 = 0.01 μF, C2 = 0.01 μF, C3 = 4.7 μF.

5-9344(F)

Figure 13. Sample Power Supply Filter Network for Analog HSI Power Supply Pins

C2+ C3+

TO DEVICE

PLL_VDDA

PLL_VSSA

C1+

FROM POWER

SUPPLY SOURCE

Lattice Semiconductor 42

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

LVDS I/O

Table 21. LVDS Driver dc Data*

* External reference, REF10 = 1.0 V ± 3%, REF14 = 1.4 V ± 3%

Table 22. LVDS Driver ac Data

Parameter Symbol Test Conditions Min Typ Max Unit

Driver Output Voltage High, VOA or VOB VOH RLOAD = 100 Ω ± 1% — — 1.475* V

Driver Output Voltage Low, VOA or VOB VOL RLOAD = 100 Ω ± 1% 0.925* — — V

Driver Output Differential Voltage

VOD = (VOA – VOB)

(with External Reference Resistor)

VOD RLOAD = 100 Ω ± 1% 0.25 — 0.45* V

Driver Output Offset Voltage

VOS = (VOA + VOB)/2

VOS RLOAD = 100 Ω ± 1% 1.125* — 1.275* V

Output Impedance, Single Ended RoVCM = 1.0 V and 1.4 V 40 50 60 Ω

RO Mismatch Between A and B delta ROVCM = 1.0 V and 1.4 V — — 10 %

Change in |VOD| Between 0 and 1 — RLOAD = 100 Ω ± 1% — — 25 mV

Change in |VOS| Between 0 and 1 — RLOAD = 100 Ω ± 1% — — 25 mV

Output Current ISA, ISB Driver shorted to

ground

——24mA

Output Current ISAB Drivers shorted

together

——12mA

Power-off Output Leakage |xa|, |xb| VDD = 0 V

VPAD, VPADN = 0 V—3 V

— — 30 µA

Parameter Symbol Test Conditions Min Max Unit

VOD Fall Time, 80% to 20% TFALL ZLOAD = 100 Ω ± 1%

CPAD = 3 pF, CPAD = 3 pF

100 200 ps

VOD Rise Time, 20% to 80% TRISE ZLOAD = 100 Ω ± 1%

CPAD = 3 pF, CPAD = 3 pF

100 200 ps

Differential Skew

|tpHLA – tpLHB| or

|tpHLB – tpLHA|

TSKEW1 Any differential pair on package at 50% point

of the transition

—50ps

Channel-to-channel Skew

|tpDIFFm – tpDIFFn|,

TSKEW2 Any two signals on package at 0 V differential — — ps

Propagation Delay Time TPLH

TPHL

ZLOAD = 100 W ± 1%

CPAD = 3 pF, CPADN = 3 pF

0.50

0.55

0.90

1.03

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

43 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

LVDS I/O (continued)

LVDS Receiver Buffer Requirements

Table 23. LVDS Receiver dc Data

* Buffer will not produce output transition when input is open-circuited.

Note: VDD = 3.1 V—3.5 V, 0 °C —125 °C , slow-fast process.

Table 24. LVDS Receiver ac Data

Table 25. LVDS Receiver Power Consumption

Table 26. LVDS Operating Parameters

Note: Under worst-case operating condition, the LVDS driver will withstand a disabled or unpowered receiver for an

unlimited period of time without being damaged. Similarly, when outputs are short-circuited to each other or to

ground, the LVDS will not suffer permanent damage. The LVDS driver supports hot-insertion. Under a well-controlled environment,

the LVDS I/O can drive backplane as well as cable.

Parameter Symbol Test Conditions Min Typ Max Unit

Receiver Input Voltage Range, VIA or

VIB

VI|VGPD| < 925 mVdc 1 MHz 0 1.2 2.4 V

Receiver Input Differential Threshold |VIDTH||VGPD| < 925 mV 400 MHz –100 — 100 mV

Receiver Input Differential Hysteresis VHYST VIDTHH – VIDTHL ———*mV

Receiver Differential Input Impedance RIN With built-in termination,

center-tapped

80 100 120 Ω

Symbol Parameter Test Conditions Min Max Unit

TPWD Receiver Output Pulse-width Distortion |VIDTH| = 100 mV

311 MHz

— TBD ps

TPLH, TPHL Propagation Delay Time CL = 1.5 pF 0.75

0.74

1.65

1.82

— With Common-mode Variation, (0 V to 2.4 V) CL = 1.5 pF — 50 ps

TRISE Receiver Output Signal Rise Time, VOD 20% to 80% CL = 1.5 pF 150 350 ps

TFALL Receiver Output Signal Fall Time, VOD 80% to 20% CL = 1.5 pF 150 350 ps

Symbol Parameter Test Conditions Min Max Unit

PRdc Receiver dc Power dc — 34.8 mW

PRac Receiver ac Power ac, CL = 1.5 pF — 0.026 mW/MHz

Parameter Test Conditions Min Normal Max Unit

Transmit Termination Resistor — — 100 — Ω

Receiver Termination Resistor — — 50 — Ω

Temperature Range — –40 — 125 ˚C

Power Supply VDD — 3.1 — 3.5 V

Power Supply VSS ——0—V

4444 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Timing Characteristics

Description

The most accurate timing characteristics are reported

by the timing analyzer in the ispLEVER development

system. A timing report provided by the development

system after layout divides path delays into logic and

routing delays. The timing analyzer can also provide

logic delays prior to layout. While this allows routing

budget estimates, there is wide variance in routing

delays associated with different layouts.

The logic timing parameters noted in the Electrical

Characteristics section of this data sheet are the same

as those in the design tools. In the PFU timing, symbol

names are generally a concatenation of the PFU oper-

ating mode and the parameter type. The setup, hold,

and propagation delay parameters, deﬁned below, are

designated in the symbol name by the SET, HLD, and

DEL characters, respectively.

The values given for the parameters are the same as

those used during production testing and speed bin-

ning of the devices. The junction temperature and sup-

ply voltage used to characterize the devices are listed

in the delay tables. Actual delays at nominal tempera-

ture and voltage for best-case processes can be much

better than the values given.

It should be noted that the junction temperature used in

the tables is generally 85 °C. The junction temperature

for the FPGA depends on the power dissipated by the

device, the package thermal characteristics (ΘJA), and

the ambient temperature, as calculated in the following

equation and as discussed further in the Package

Thermal Characteristics Summary section:

TJmax = TAmax + (P • ΘJA) °C

Note: The user must determine this junction tempera-

ture to see if the delays from ispLEVER should

be derated based on the following derating

tables.

Table 27 and Table 28 provide approximate power sup-

ply and junction temperature derating for OR3LP26B

commercial devices. The delay values in this data

sheet and reported by ispLEVER are shown as 1.00 in

the tables. The method for determining the maximum

junction temperature is deﬁned in the Package Thermal

Characteristics section. Taken cumulatively, the range

of parameter values for best-case vs. worst-case pro-

cessing, supply voltage, and junction temperature can

approach three to one.

Table 27. Derating for Commercial Devices (I/O

Supply VDD)

Table 28. Derating for Commercial Devices (I/O

Supply VDD2)

Note: The derating tables shown above are for a typical critical path

that contains 33% logic delay and 66% routing delay. Since the

routing delay derates at a higher rate than the logic delay,

paths with more than 66% routing delay will derate at a higher

rate than shown in the table. The approximate derating values

vs. temperature are 0.26% per °C for logic delay and 0.45%

per °C for routing delay. The approximate derating values vs.

voltage are 0.13% per mV for both logic and routing delays at

25 °C.

(°C)

Power Supply Voltage

3.0 V 3.3 V 3.6 V

–40 0.82 0.72 0.66

0 0.91 0.80 0.72

25 0.98 0.85 0.77

85 1.00 0.99 0.90

100 1.23 1.07 0.94

125 1.34 1.15 1.01

(°C)

Power Supply Voltage

2.38 V 2.5 V 2.63 V

–40 0.86 0.71 0.67

0 0.94 0.79 0.73

25 0.99 0.84 0.77

85 1.00 0.99 0.92

100 1.23 1.05 0.96

125 1.33 1.13 1.03

Lattice Semiconductor 45

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Timing Characteristics (continued)

Propagation Delay—The time between the speciﬁed

reference points. The delays provided are the worst-

case of the tphh and tpll delays for noninverting func-

tions, tplh and tphl for inverting functions, and tphz and

tplz for 3-state enable.

Setup Time—The interval immediately preceding the

transition of a clock or latch enable signal, during which

the data must be stable to ensure it is recognized as

the intended value.

Hold Time—The interval immediately following the

transition of a clock or latch enable signal, during which

the data must be held stable to ensure it is recognized

as the intended value.

3-State Enable—The time from when a 3-state control

signal becomes active and the output pad reaches the

high-impedance state.

PFU Timing

Refer to

ORCA

Series 3 data sheet for the following:

Combination PFU Timing Characteristics

Sequential PFU Timing Characteristics

Ripple Mode PFU Timing Characteristics

Synchronous Memory Write Characteristics

Synchronous Memory Read Characteristics

PLC Timing

Refer to

ORCA

Series 3 data sheet for the following:

PFU Output MUX and Direct Routing Timing Charac-

teristics

SLIC Timing

Refer to

ORCA

Series 3 data sheet for the following:

Supplemental Logic and Interconnect Cell (SLIC) Tim-

ing Characteristics

PIO Timing

Refer to

ORCA

Series 3 data sheet for the following:

Programmable I/O (PIO) Timing Characteristics

Special Function Timing

Refer to

ORCA

Series 3 data sheet for the following:

Microprocessor Interface (MPI) Timing Characteristics

Programmable Clock Manager (PCM) Timing Charac-

teristics

Boundary-Scan Timing Characteristics

Clock Timing

Refer to

ORCA

Series 3 data sheet for the following:

ExpressCLK (ECLK) and Fast Clock (FCLK) Timing

Characteristics

General-Purpose Clock Timing Characteristics (Inter-

nally Generated Clock)

ORT4622 ExpressCLK to Output Delay (Pin-to-Pin)

ORT4622 Fast Clock (FCLK) to Output Delay (Pin-to-

Pin)

ORT4622 General System Clock (SCLK) to Output

Delay (Pin-to-Pin)

ORT4622 Input to ExpressCLK (ECLK) Fast Capture

Setup/Hold Time (Pin-to-Pin)

ORT4622 Input to Fast Clock Setup/Hold Time (Pin-to-

Pin)

ORT4622 Input to General System Clock Setup/Hold

Time (Pin-to-Pin)

Conﬁguration Timing

Refer to

ORCA

Series 3 data sheet for Conﬁguration

Timing Characteristics.

Readback Timing

Refer to

ORCA

Series 3 data sheet for Readback Tim-

ing Characteristics.

Lattice Semiconductor 46

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

Table 29. ORT4622 Embedded Core and FPGA Interface Clock Operation Frequencies

ORT4622 Commercial: VDD = 3.3 V ± 5%, VDD2 = 2.5 V ± 5%, 0 °C < TA < 70 °C.

* The sys_clk clock frequency is based on the HSI macro speciﬁcations.

All embedded core/FPGA on-chip interface timing is available in ispLEVER through the STAMP timing ﬁle included

in the ORT4622 Design Kit.

Description

(TI = 85 °C, VDD = min, VDD2 = min)

Speed

–7 Unit

Signal Min Typ Max

sys_clk 0 —* 77.76* MHz

toh_clk 0 25 77.76 MHz

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

47 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

Clock Timing

5-8605 (F)

Figure 14. Transmit Parallel Port Timing (Backplane -> FPGA)

Table 30. Timing Requirements (Transmit Parallel Port Timing)

Symbol Parameter Min Nom Max Unit

TPClock Period 12.86 — — ns

TLClock Low Time 5.1 6.43 7.7 ns

THClock High Time 5.1 6.43 7.7 ns

FIRST A1 OF STS1 #1

FPGA_SYSCLK

SYS_FP

DATA_TX BUS

(DATA BUS

FROM FPGA

TO EMBEDDED

CORE)

Lattice Semiconductor 48

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8606

Figure 15. Transmit Transport Delay (FPGA -> Backplane)

Table 31. Timing Requirements (Transmit Transport Delay)

Symbol Parameter Min Nom Max Unit

TPROP Number of Clocks of Delay from Parallel

Bus Input to LVDS Output

4 7 8 SYS_CLK

TPROP

A1 OF STS1 #1

SYS_CLK

SYS_FP

DATA_TX BUS

(PARALLEL

DATA

FROM FPGA

TO EMBEDDED

CORE)

HDOUT

(LVDS

DATA

OUT) FIRST A1 OF STS1 #1

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

49 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8607 (F)

Figure 16. Receive Parallel Port Timing (Backplane -> FPGA)

Table 32. Timing Requirements (Receive Parallel Port Timing)

Symbol Parameter Min Nom Max Unit

TPClock Period 12.86 — — ns

TLClock Low Time 5.1 6.43 7.7 ns

THClock High Time 5.1 6.43 7.7 ns

SYS_CLK

LINE_FP

DATA_RX BUS

(FROM EMBEDDED

CORE TO

FPGA) FIRST A1 OF STS1 #1

PARITY,

SPE,

C1J1 PINS

Lattice Semiconductor 50

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8608 (F)

* Data bus refers to 8 bits data, 1 bit parity, 1 bit SPE, and 1 bit C1J1.

† Channel A or C refers to whether the PROT_SW_A or PROT_SW_C pins that are activated. For example, if the PROT_SW_A pin is

activated, the timing diagram for output bus A or C refers to output bus A.

Figure 17. Protection Switch Timing

Table 33. Timing Requirements (Protection Switch Timing)

Symbol Parameter Min Nom Max Unit

TTR Transport Delay from Latching of

PROT_SW_A/C to Actual Data Switch

7 8 9 Leading edge

SYS_CLKs

THIZ Transport Delay from Latching of

PROT_SW_A/C to Actual Hi-z

4 5 6 Leading edge

SYS_CLKs

TCH Propagation Delay from

SYS_CLK to HI-Z of Output Bus

— — 25 Leading edge

SYS_CLKs

SYS_CLK

PROT_SW_A

...

PROT_SW_C

...

DATA_RX BUS*

A OR C

SYS_CLK

DATA_RX BUS†

A & B OR

C & D

CH A/C CH A/C CH A/C CH A/C CH B/D

TTR

THIZ TCH

CH A & B/

CH C & D

CH A & B/

CH C & D

CH A & B/

CH C & D

CH A & B/

CH C & D

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

51 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8609 (F)

Figure 18. TOH Input Serial Port Timing (FPGA -> Backplane)

Table 34. Timing Requirements (TOH Input Serial Port Timing)

Symbol Parameter Min Nom Max Unit

TPClock Period 12.86 — 40 ns

THI Clock High Time 5.1 6.43 7.7 ns

TLO Clock Low Time 5.1 6.43 7.7 ns

SYS_CLK

SYS_FP

...

DATA_TX BUS

TOH_CLK

1044 bytes SPE

...

TX TOH_

(PARALLEL

BUS)

TOH SERIAL

INPUT

CLK_ENA

ROW #1 ROW #9

36 bytes TOH 1044 bytes SPE 36 bytes TOH

GUARD BAND

(4 TOH CLK)

GUARD BAND

(4 TOH CLK)

MSbit(7)

OF B1 byte

STS1 #1

bit 6

OF B1 byte

STS1 #1

THI TLO

Lattice Semiconductor 52

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8610 (F)

Note: The total delay from A1 STS1 #1 arriving at LVDS input to RX_TOH_FP is 56 SYS_CLKs and 6 TOH_CLKs. This will vary by ±14

SYS_CLKs, 12 each way for the FIFO alignment, and ±2 SYS_CLKs due to the variability in the clock recovery of the HSI macro.

Figure 19. TOH Output Serial Port Timing (Backplane -> FPGA)

Table 35. Timing Requirements (TOH Output Serial Port Timing)

Symbol Parameter Min Nom Max Unit

TTRANS_SYS Delay from First A1 LVDS Serial Input to

Transfer to TOH_CLK

44 56 68 SYS_CLKs

TTRANS_TOH Delay from Transfer to TOH_CLK to

RX_TOH_FP

— 6 — TOH_CLKs

RX TOH FP

HDIN

TOH_CLK

1044 bytes SPE

RX TOH

(INPUT LVDS

SERIAL 622M

DATA)

TOH SERIAL

OUTPUT

CLK ENA

ROW #1 ROW #9

36 bytes TOH 1044 bytes SPE 36 bytes TOH

MSbit(7)

OF A1 byte

STS #1

bit 6

OF A1 byte

STS #1

TTRANS_SYS

TTRANS_TOH

bit 0

OF A1 byte

STS #1

...

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

53 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8611 (F)

Note: The CPU interface can be bit stream selected either from device I/O or FPGA interface. The timing diagram applies to both interfaces, but

not to the FPGA MPI block.

Figure 20. CPU Write Transaction

Table 36. Timing Requirements (CPU Write Transaction)

Symbol Parameter Min Max Unit

TPULSE Minimum Pulse Width for CS_N 5 — ns

TADDR_MAX Maximum Time from Negative Edge

of CS_N to ADDR Valid

—18ns

TDAT_MAX Maximum Time from Negative Edge

of CS_N to Data Valid

—25ns

TRD_WR_MAX Maximum Time from Negative Edge

of CS_N to Negative Edge of RD_WR_N

—26ns

TWRITE_MAX Maximum Time from Negative Edge of CS_N to

Contents of Internal Register Latching DB[7:0]

— 60 ns

TACCESS_MIN Minimum Time Between a Write Cycle (falling

edge of CS_N) and Any Other Transaction

(read or write at falling edge of CS_N)

60 — ns

TINT_MAX Maximum Time from Register FF to Pad — 20 ns

TRW_WR_N,

ADDR, DB_HOLD

Minimum Hold Time that RD_WR_N,

ADDR and DB Must be Held Valid from

the Negative Edge of CS_N

57 — ns

DATA VALID

TACCESS_MIN

TPULSE

OLD VALUE NEW VALUE

TWRITE_MAX

TINT_MAX

TADDR_MAX

TDAT_MAX RD_WR_MAX

CPU_CS_N

CPU_RD_WR_N

CPU_ADDR[6:0]

CPU_DATA[7:0]

INTERNAL REGISTER

(SYS_CLK

DOMAIN)

CPU_INT_N

TRD_WR_N, ADDR_MAX, DB_HOLD

(CS_N)

(RD_WR_N)

(ADDR[6:0])

(DB[7:0])

(INT_N)

Lattice Semiconductor 54

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Timing Characteristics (continued)

5-8612 (F)

Notes:

The CPU interface can be bit stream selected either from device I/O or FPGA interface. The timing diagram applies to both interfaces, but not to

the FPGA MPI block.

The time delay between the advanced SYS_CLK and the distributed SYS_CLK used to sample CS_N is of no consequence. However, the

path delay of CS_N from pad to where is it sampled by SYS_CLK must be minimized.

The calculated delays assume a 100 pF loading on the DB pins.

Figure 21. CPU Read Transaction

Table 37. Timing Requirements (CPU Read Transaction)

Symbol Parameter Min Max Unit

TPULSE Minimum Pulse Width for CS_N 5 — ns

TADDR_MAX Maximum Time from Negative Edge of

CS_N to ADDR Valid

—5 ns

TRD_WR_MAX Maximum Time from Negative Edge of

CS_N to RD_WR_N Falling

—5 ns

TDATA_MAX Maximum Time from Negative Edge of

CS_N to Data Valid on DB Port

—56 ns

THIZ_MAX Maximum Time from Rising Edge of

CS_N to DB Port Going HI-Z

—12 ns

TACCESS_MIN Minimum Time Between a Read Cycle

(falling edge of CS_N) and Any Other Transaction

(read or write at falling edge of CS_N)

60 — ns

DATA VALID

TACCESS_MIN

TPULSE

TDATA_MAX

CPU_CS_N

CPU_RD_WR_N

CPU_ADDR[6:0]

CPU_DATA[7:0]

THIZ_MAX

TADDR_MAX

TRD_WR_MAX

(CS_N)

(RD_WR_N)

(ADDR[6:0])

(DB[7:0])

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

55 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Input/Output Buffer Measurement Conditions (on-LVDS Buffer)

Note: Switch to VDD for TPLZ/TPZL; switch to GND for TPHZ/TPZH.

Figure 22. ac Test Loads

5-3233.a(F)

Figure 23. Output Buffer Delays

5-3235(F)

Figure 24. Input Buffer Delays

5-3234(F)

50 pF

A. Load Used to Measure Propagation Delay

TO THE OUTPUT UNDER TEST

50 pF

VCC GND

1 kΩ

B. Load Used to Measure Rising/Falling Edges

VDD

TPHH

VDD/2

VSS

out[i]

PAD

OUT 1.5 V

0.0 V

TPLL

PAD

out[i] ac TEST LOADS (SHOWN ABOVE)

ts[i]

OUT

0.0 V

1.5 V

TPHH

TPLL

PAD in[i]

3.0 V

VSS

VDD/2

VDD

PAD IN

in[i]

5656 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

FPGA Output Buffer Characteristics

5-6865(F)

Figure 25. Sinklim (TJ = 25 ¡C, VDD = 3.3 V)

5-6867(F)

Figure 26. Slewlim (TJ = 25 ¡C, VDD = 3.3 V)

5-6867(F)

Figure 27. Fast (TJ = 25 ¡C, VDD = 3.3 V)

5-6866(F)

Figure 28. Sinklim (TJ = 125 ¡C, VDD = 3.0 V)

5-6868(F)

Figure 29. Slewlim (TJ = 125 ¡C, VDD = 3.0 V)

5-6868(F)

Figure 30. Fast (TJ = 125 ¡C, VDD = 3.0 V)

0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5

110

OUTPUT VOLTAGE, VO (V)

IOL

IOH

OUTPUT CURRENT, IO (mA)

100

0.0 0.5 1.0 1.5 2.0 2.5 3.0

OUTPUT VOLTAGE, VO (V)

IOL

100

IOH

OUTPUT CURRENT, IO (mA)

120

140

3.5

0.0 0.5 1.0 1.5 2.0 2.5 3.0

OUTPUT VOLTAGE, VO (V)

IOL

100

IOH

OUTPUT CURRENT, IO (mA)

120

140

3.5

0.0 0.5 1.0 1.5 2.0 2.5 3.0

OUTPUT VOLTAGE, VO (V)

IOL

IOH

OUTPUT CURRENT, IO (mA)

0.0 0.5 1.0 1.5 2.0 2.5 3.0

OUTPUT VOLTAGE, VO (V)

IOL

100

IOH

OUTPUT CURRENT, IO (mA)

120

0.0 0.5 1.0 1.5 2.0 2.5 3.0

OUTPUT VOLTAGE, VO (V)

IOL

100

IOH

OUTPUT CURRENT, IO (mA)

120

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

57 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

LVDS Buffer Characteristics

Termination Resistor

The LVDS drivers and receivers operate on a 100 Ω differential impedance, as shown below. External resistors are

not required. The differential driver and receiver buffers include termination resistors inside the device package as

shown in Figure 31 below.

5-8703(F)

Figure 31. LVDS Driver and Receiver and Associated Internal Components

LVDS Driver Buffer Capabilities

Under worst-case operating condition, the LVDS driver must withstand a disabled or unpowered receiver for an

unlimited period of time without being damaged. Similarly, when its outputs are short-circuited to each other or to

ground, the LVDS driver will not suffer permanent damage. Figure 32 illustrates the terms associated with LVDS

driver and receiver pairs.

5-8704(F)

Figure 32. LVDS Driver and Receiver

5-8705(F)

Figure 33. LVDS Driver

LVDS DRIVER

50 Ω

LVDS RECEIVER

CENTER TAP

DEVICE PINS

100 Ω

EXTERNAL

VGPD

VOA

VOB

VIA

VIB

DRIVER INTERCONNECT RECEIVER

VOA A

VOB B

RLOAD VOD = (VOA – VOB)V

Lattice Semiconductor 58

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Estimating Power Dissipation

The total operating power dissipated is estimated by summing the FPGA standby (IDDSB), internal, and external

power dissipated, in addition to the embedded block power.

Table 38. Embedded Block Power Dissipation

Note: Power is calculated assuming an activity factor of 20%.

The following discussion relates to the FPGA portion of the device. The internal and external power is the power

consumed in the PLCs and PICs, respectively. In general, the standby power is small and may be neglected. The

total operating power is as follows:

PT = Σ PPLC + Σ PPIC

The internal operating power is made up of two parts: clock generation and PFU output power. The PFU output

power can be estimated based upon the number of PFU outputs switching when driving an average fan-out of two:

PPFU = 0.078 mW/MHz

For each PFU output that switches, 0.136 mW/MHz needs to be multiplied times the frequency (in MHz) that the

output switches. Generally, this can be estimated by using one-half the clock rate, multiplied by some activity fac-

tor; for example, 20%.

The power dissipated by the clock generation circuitry is based upon four parts: the ﬁxed clock power, the power/

clock branch row or column, the clock power dissipated in each PFU that uses this particular clock, and the power

from the subset of those PFUs that are conﬁgured as synchronous memory. Therefore, the clock power can be cal-

culated for the four parts using the following equations:

ORT4622 Clock Power

P = [0.22 mW/MHz

+ (0.39 mW/MHz/Branch) (# Branches)

+ (0.008 mW/MHz/PFU) (# PFUs)

+ (0.002 mW/MHz/PIO (# PIOs)]

For a quick estimate, the worst-case (typical circuit) ORT4622 clock power = 4.8 mW/MHz

The power dissipated in a PIC is the sum of the power dissipated in the four PIOs in the PIC. This consists of power

dissipated by inputs and ac power dissipated by outputs. The power dissipated in each PIO depends on whether it

is conﬁgured as an input, output, or input/output. If a PIO is operating as an output, then there is a power dissipa-

tion component for PIN, as well as POUT. This is because the output feeds back to the input.

The power dissipated by an input buffer is (VIH = VDD – 0.3 V or higher) estimated as:

PIN = 0.09 mW/MHz

The ac power dissipation from an output or bidirectional is estimated by the following:

POUT = (CL + 8.8 pF) × VDD2 × F Watts

where the unit for CL is farads, and the unit for F is Hz.

Number of Active Channels Operating

Frequency (Hz)

Estimated Power Dissipated (Watt)

Min Max

1 channel 622 — 1.08

2 channels 622 — 1.43

3 channels 622 — 1.73

4 channels 622 — 2.01

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

59 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information

This section describes the pins and signals that perform FPGA-related functions. During conﬁguration, the user-

programmable I/Os are 3-stated and pulled-up with an internal resistor. If any FPGA function pin is not used (or not

bonded to package pin), it is also 3-stated and pulled-up after conﬁguration.

Table 39. FPGA Common-Function Pin Description

* The

ORCA

Series 3 FPGA data sheet contains more information on how to control these signals during start-up. The timing of DONE release

is controlled by one set of bit stream options, and the timing of the simultaneous release of all other conﬁguration pins (and the activation of all

user I/Os) is controlled by a second set of options.

Symbol I/O Description

Dedicated Pins

VDD — 3.3 V power supply.

VDD2 — 2.5 V power supply

GND — Ground supply.

RESET I During conﬁguration, RESET forces the restart of conﬁguration and a pull-up is enabled.

After conﬁguration, RESET can be used as an FPGA logic direct input, which causes all

PLC latches/FFs to be asynchronously set/reset.

CCLK I/O In the master and asynchronous peripheral modes, CCLK is an output, which strobes

conﬁguration data in. In the slave or synchronous peripheral mode, CCLK is input syn-

chronous with the data on DIN or D[7:0]. In microprocessor mode, CCLK is used inter-

nally and output for daisy-chain operation.

DONE I As an input, a low level on DONE delays FPGA start-up after conﬁguration.*

O As an active-high, open-drain output, a high level on this signal indicates that conﬁgura-

tion is complete. DONE has a permanent pull-up resistor.

PRGM I PRGM is an active-low input that forces the restart of conﬁguration and resets the bound-

ary-scan circuitry. This pin always has an active pull-up.

RD_CFG I This pin must be held high during device initialization until the INIT pin goes high. This

pin always has an active pull-up.

During conﬁguration, RD_CFG is an active-low input that activates the TS_ALL function

and 3-states all of the I/O.

After conﬁguration, RD_CFG can be selected (via a bit stream option) to activate the

TS_ALL function as described above, or, if readback is enabled via a bit stream option, a

high-to-low transition on RD_CFG will initiate readback of the conﬁguration data, includ-

ing PFU output states, starting with frame address 0.

RD_DATA/TDO O RD_DATA/TDO is a dual-function pin. If used for readback, RD_DATA provides conﬁgura-

tion data out. If used in boundary scan, TDO is test data out.

Special-Purpose Pins

M0, M1, M2 I During powerup and initialization, M0, M1, and M2 are used to select the conﬁguration

mode with their values latched on the rising edge off INIT. During conﬁguration, a pull-up

is enabled. After conﬁguration, these pins cannot be user-programmable

I/Os.

M3 I During powerup and initialization, M3 is used to select the speed of the internal oscillator

during conﬁguration with their values latched on the rising edge of INIT. When M3 is low,

the oscillator frequency is 10 MHz. When M3 is high, the oscillator is 1.25 MHz. During

conﬁguration, a pull-up is enabled.

I/O After conﬁguration, this pin is a user-programmable I/O pin.*

Lattice Semiconductor 60

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

Table 39. FPGA Common-Function Pin Description (continued)

* The

ORCA

Series 3 FPGA data sheet contains more information on how to control these signals during start-up. The timing of DONE release

is controlled by one set of bit stream options, and the timing of the simultaneous release of all other conﬁguration pins (and the activation of all

user I/Os) is controlled by a second set of options.

Symbol I/O Description

Special-Purpose Pins (continued)

TDI, TCK, TMS I If boundary scan is used, these pins are test data in, test clock, and test mode select

inputs. If boundary scan is not selected, all boundary-scan functions are inhibited

once conﬁguration is complete. Even if boundary scan is not used, either TCK or

TMS must be held at logic one during conﬁguration. Each pin has a pull-up enabled

during conﬁguration.

I/O After conﬁguration, these pins are user-programmable I/O.*

RDY/RCLK/

MPI_ALE

O During conﬁguration in peripheral mode, RDY/RCLK indicates another byte can be

written to the FPGA. If a read operation is done when the device is selected, the

same status is also available on D7 in asynchronous peripheral mode.

O During the master parallel conﬁguration mode, RCLK is a read output signal to an

external memory. This output is not normally used.

I In

i960

microprocessor mode, this pin acts as the address latch enable (ALE) input.

I/O After conﬁguration, if the MPI is not used, this pin is a user-programmable I/O pin.*

HDC O High during conﬁguration (HDC) is output high until conﬁguration is complete. It is

used as a control output indicating that conﬁguration is not complete.

LDC O Low during conﬁguration (LDC) is output low until conﬁguration is complete. It is

used as a control output indicating that conﬁguration is not complete.

INIT I/O INIT is a bidirectional signal before and during conﬁguration. During conﬁguration, a

pull-up is enabled, but an external pull-up resistor is recommended. As an active-low

open-drain output, INIT is held low during power stabilization and internal clearing of

memory. As an active-low input, INIT holds the FPGA in the wait-state before the

start of conﬁguration.

CS0, CS1 I CS0 and CS1 are used in the asynchronous peripheral, slave parallel, and micropro-

cessor conﬁguration modes. The FPGA is selected when CS0 is low and CS1 is

high. During conﬁguration, a pull-up is enabled.

I/O After conﬁguration, these pins are user-programmable I/O pins.*

RD/MPI_STRB IRD is used in the asynchronous peripheral conﬁguration mode. A low on RD

changes D7 into a status output. As a status indication, a high indicates ready, and a

low indicates busy. WR and RD should not be used simultaneously. If they are, the

write strobe overrides.

This pin is also used as the microprocessor interface (MPI) data transfer strobe. For

PowerPC

, it is the transfer start (TS). For

i960

, it is the address/data strobe (ADS).

I/O After conﬁguration, if the MPI is not used, this pin is a user-programmable I/O pin.*

WR IWR is used in the asynchronous peripheral conﬁguration mode. When the FPGA is

selected, a low on the write strobe, WR, loads the data on D[7:0] inputs into an inter-

nal data buffer. WR and RD should not be used simultaneously. If they are, the write

strobe overrides.

I/O After conﬁguration, this pin is a user-programmable I/O pin.*

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

61 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

Table 39. FPGA Common-Function Pin Description (continued)

* The

ORCA

Series 3 FPGA data sheet contains more information on how to control these signals during start-up. The timing of DONE release

is controlled by one set of bit stream options, and the timing of the simultaneous release of all other conﬁguration pins (and the activation of all

user I/Os) is controlled by a second set of options.

Symbol I/O Description

Special-Purpose Pins (continued)

MPI_IRQ O MPI active-low interrupt request output.

MPI_BI O

PowerPC

mode MPI burst inhibit output.

I/O If the MPI is not in use, this is a user-programmable I/O.

MPI_ACK O In

PowerPC

mode MPI operation, this is the active-high transfer acknowledge (TA)

output. For

i960

MPI operation, it is the active-low ready/record (RDYRCV) output.

If the MPI is not in use, this is a user-programmable I/O.

MPI_RW I In

PowerPC

mode MPI operation, this is the active-low write/active-high read control

signals. For

i960

operation, it is the active-high write/active-low read control signal.

I/O If the MPI is not in use, this is a user-programmable I/O.

MPI_CLK I This is the clock used for the synchronous MPI interface. For

PowerPC

, it is the CLK-

OUT signal. For

i960

, it is the system clock that is chosen for the

i960

external bus

interface.

I/O If the MPI is not in use, this is a user-programmable I/O.

A[4:0] I For

PowerPC

operation, these are the

PowerPC

address inputs. The address bit

mapping (in

PowerPC

/FPGA notation) is A[31]/A[0], A[30]/A[1], A[29]/A[2], A[28]/

A[3], A[27]/A[4]. Note that A[27]/A[4] is the MSB of the address. The A[4:2] inputs

are not used in

i960

MPI

mode.

I/O If the MPI is not in use, this is a user-programmable I/O.

A[1:0]/MPI_BE[1:0] I For

i960

operation, MPI_BE[1:0] provide the

i960

byte enable signals, BE[1:0], that

are used as address bits A[1:0] in

i960

byte-wide operation.

D[7:0] I During peripheral and slave parallel conﬁguration modes, D[7:0] receive conﬁgura-

tion data, and each pin has a pull-up enabled. During serial conﬁguration modes, D0

is the DIN input. D[7:0] are also the data pins for

PowerPC

microprocessor mode

and the address/data pins for

i960

microprocessor mode.

I/O After conﬁguration, the pins are user-programmable I/O pins.*

DIN I During slave serial or master serial conﬁguration modes, DIN accepts serial conﬁgu-

ration data synchronous with CCLK. During parallel conﬁguration modes, DIN is the

D0 input. During conﬁguration, a pull-up is enabled.

I/O After conﬁguration, this pin is a user-programmable I/O pin.*

DOUT O During conﬁguration, DOUT is the serial data output that can drive the DIN of daisy-

chained slave LCA devices. Data out on DOUT changes on the falling edge of

CCLK.

I/O After conﬁguration, DOUT is a user-programmable I/O pin.*

Lattice Semiconductor 62

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

This section describes device I/O signals to/from the embedded core excluding the signals at the CIC boundary.

Table 40. FPSC Function Pin Description

Symbol I/O Description

HSI LVDS Pins

sts_ina I LVDS input receiver A.

sts_inan I LVDS input receiver A.

sts_inb I LVDS input receiver B.

sts_inbn I LVDS input receiver B.

sts_inc I LVDS input receiver C.

sts_incn I LVDS input receiver C.

sts_ind I LVDS input receiver D.

sts_indn I LVDS input receiver D.

sts_outa O LVDS output receiver A.

sts_outan O LVDS output receiver A.

sts_outb O LVDS output receiver B.

sts_outbn O LVDS output receiver B.

sts_outc O LVDS output receiver C.

sts_outcn O LVDS output receiver C.

sts_outd O LVDS output receiver D.

sts_outdn O LVDS output receiver D.

ctap_refa — LVDS input center tap (RX A) (use 0.01 µF to GND).

ctap_refb — LVDS input center tap (RX B) (use 0.01 µF to GND).

ctap_refc — LVDS input center tap (RX C) (use 0.01 µF to GND).

ctap_refd — LVDS input center tap (RX D) (use 0.01 µF to GND).

ref10 I LVDS reference voltage: 1.0 V ± 3%.

ref14 I LVDS reference voltage: 1.4 V ± 3%.

reshi — Resistor input (use 100 Ω ± 1% to RESLO input).

reslo — Resistor input.

rext — Reference resistor for PLL (10 kΩ to ground).

pll_VDDA — PLL analog VDD (3.3 V ± 5%).

pll_VSSA — PLL analog VSS (GND).

HSI Test Signals

tstmode I Enables CDR test mode. Internal pull-down.

bypass I Enables bypassing of the 622 MHz clock synthesis with TSTCLK. Internal

pull-down.

tstclk I Test clock for emulation of 622 MHz clock during PLL bypass. Internal pull-

down.

mreset I Test mode reset. Internal pull-down.

resetrn I Resets receiver clock division counter. Internal pull-up.

resettn I Resets transmitter clock division counter. Internal pull-up.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

63 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

Table 40. FPSC Function Pin Description (continued)

* BSCAN pins-TDI, TDO, TCK, and TMS are on FPGA side.

Symbol I/O Description

HSI Test Signals (continued)

tstshftld I Enables the test mode control register for shifting in selected tests by a

serial port. Internal pull-down

ecsel I Enables external test control of 622 MHz clock phase selection. Internal

pull-down

exdnup I Direction of phase change. Internal pull-down

etoggle I Moves 622.08 MHz clock selection on phase per positive pulse. Internal

pull-down

loopbken I Enables 622 Mbits/s loopback mode. Internal pull-down

tstphase I Controls bypass of 16 PLL-generated phases with 16 low-speed phases.

Internal pull-down

tstmux[8:0]s O Test mode output port.

CPU Interface Pins

db<7:0> I/O CPU interface data bus. Internal pull-up.

addr<6:0> I CPU interface address bus. Internal pull-up.

rd_wr_n I CPU interface read/write. Internal pull-up.

cs_n I Chip select. Internal pull-up.

int_n O Interrupt output. Internal pull-up. Open drain.

MISC System Signals

rst_n I Reset the Core only. The FPGA logic is not reset by rst_n.

Internal pull-down allows chip to stay in reset state when external driver

loses power.

sys_clk I System clock (77.76 MHz), 50% duty cycle, also the reference clock of PLL.

Internal pull-up.

dxp — Temperature sensing diode (anode +).

dxn — Temperature sensing diode (cathode –).

SCAN and BSCAN Pins*

scan_tstmd I Scan test mode input. Internal pull-up.

scanen I Scan mode enable input. Internal pull-up.

lvds_en I LVDS enable used during BSCAN. During normal operation, lvds_en needs

to be pulled high. lvds_en needs to be pulled low for boundary scan.

Universal BIST Controller Pins

sys_dobist I sys_dobist is asserted high to start the BIST, and should be kept high dur-

ing the entire BIST operation. Internal pull-down.

sys_rssigo O This 32-bit serial out RSB signature consists of the 4-bit FSM state and the

BIST ﬂag ﬂip-ﬂop states from each SBRIC_RS element.

bc O This ﬂag is asserted to one when BIST is complete, and is used for polling

the end of BIST.

Lattice Semiconductor 64

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

In Table 41, an input refers to a signal ﬂowing into the FGPA logic (out of the embedded core) and an output refers

to a signal ﬂowing out of the FPGA logic (into the embedded core).

Table 41. Embedded Core/FPGA Interface Signal Description

Pin Name I/O Description

data_txa<7:0> O Parallel bus of transmitter A. MSB is bit 7.

data_txa_par O Parity for transmitter A.

data_txb<7:0> O Parallel bus of transmitter B. MSB is bit 7.

data_txb_par O Parity for transmitter B.

data_txc<7:0> O Parallel bus of transmitter C. MSB is bit 7.

data_txc_par O Parity for transmitter C.

data_txd<7:0> O Parallel bus of transmitter D. MSB is bit 7.

data_txd_par O Parity for transmitter D.

data_rxa<7:0> I Parallel bus of receiver A. MSB is bit 7.

data_rxa_par I Parity for parallel bus of receiver A.

data_rxa_spe I SPE signal for parallel bus of receiver A.

data_rxa_c1j1 I C1J1 signal for parallel bus of receiver A.

data_rxa_en I Enable for parallel bus of receiver A.

data_rxb<7:0> I Parallel bus of receiver B. MSB is bit 7.

data_rxb_par I Parity for parallel bus of receiver B.

data_rxb_spe I SPE signal for parallel bus of receiver B.

data_rxb_c1j1 I C1J1 signal for parallel bus of receiver B.

data_rxb_en I Enable for parallel bus of receiver B.

data_rxc<7:0> I Parallel bus of receiver C. MSB is bit 7.

data_rxc_par I Parity for parallel bus of receiver C.

data_rxc_spe I SPE signal for parallel bus of receiver C.

data_rxc_c1j1 I C1J1 signal for parallel bus of receiver C.

data_rxc_en I Enable for parallel bus of receiver C.

data_rxd<7:0> I Parallel bus of receiver D. MSB is bit 7.

data_rxd_par I Parity for parallel bus of receiver D.

data_rxd_spe I SPE signal for parallel bus of receiver D.

data_rxd_c1j1 I C1J1 signal for parallel bus of receiver D.

data_rxd_en I Enable for parallel bus of receiver D.

toh_clk O TX and RX TOH serial links clock (25 MHz to 77.76 MHz).

toh_txa O TOH serial link for transmitter A.

toh_txb O TOH serial link for transmitter B.

toh_txc O TOH serial link for transmitter C.

toh_txd O TOH serial link for transmitter D.

tx_toh_ck_en O TX TOH serial link clock enable.

toh_rxa I TOH serial link for receiver A.

toh_rxb I TOH serial link for receiver B.

toh_rxc I TOH serial link for receiver C.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

65 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

Table 41. Embedded Core/FPGA Interface Signal Description (continued)

Pin Name I/O Description

toh_rxd I TOH serial link for receiver D.

rx_toh_ck_en I RX TOH serial link clock enable.

rx_toh_fp I RX TOH serial link frame pulse.

toh_ck_fp_en I A soft register bit available to enable RX TOH clock and frame

pulse.

toh_en_a I RX TOH enable, soft register. "AND" output of resistor channel

A enable and hi-z control of TOH data output A.

cpu_data_tx<7:0> O CPU interface data bus.

cpu_data_rx<7:0> I CPU interface data bus.

cpu_addr<6:0> O CPU interface address bus.

cpu_rd_wr_n O CPU interface read/write.

cpu_cs_n O Chip select.

cpu_int_n I Interrupt.

sys_fp O System frame pulse for transmitter section.

line_fp O Line frame pulse for receiver section.

fpga_sysclk I System clock (77.76 MHz).

prot_sw_a O Protection switching control signal.

prot_sw_c O Protection switching control signal.

core_ready I During powerup and FPGA conﬁguration sequence, the

core_ready is held low. At the end of FPGA conﬁguration, the

core_ready will be held low for six clock (sys_clk) cycles and

then go active-high. Flag indicates that the embedded core is

out of its reset state.

ﬁfosync_fp I The alignment FIFO synchronizes and locates the data frames

and outputs an optimal frame pulse for the four arriving data

streams.

cdr_clk_a I 77.76 MHz recovered clock for channel A.

cdr_clk_b I 77.76 MHz recovered clock for channel B.

cdr_clk_c I 77.76 MHz recovered clock for channel C.

cdr_clk_d I 77.76 MHz recovered clock for channel D.

rb_mp_sel I Bit stream selection for microprocessor interface selection.

A 0 indicates the microprocessor interface on the core side is

selected. A 1 selects the CPU interface from the FPGA side.

6666 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 42. Embedded Core/FPGA Interface Signal

Locations

Embedded

Core/FPGA

Interface

Site

FPGA Input

Signal

FPGA Output

Signal

ASB1A toh_rxa toh_txa

ASB1B toh_rxb toh_txb

ASB1C toh_rxc toh_txc

ASB1D toh_rxd toh_txd

CKTOASB1 — toh_clk

ASB2A rx_toh_ck_en —

ASB2B rx_toh_fp —

ASB2C toh_ck_fp_en tx_toh_ck_en

ASB2D toh_en_a —

ASB3A data_rxa7 —

ASB3B data_rxa6 —

ASB3C data_rxa5 —

ASB3D data_rxa4 —

ASB4A data_rxa3 —

ASB4B data_rxa2 —

ASB4C data_rxa1 —

ASB4D data_rxa0 —

ASB5A data_rxa_par prot_sw_a

ASB5B data_rxa_spe —

ASB5C data_rxa_c1j1 —

ASB5D data_rxa_en —

ASB6A data_rxtb7 —

ASB6B data_rxb6 —

ASB6C data_rxb5 —

ASB6D data_rxb4 —

ASB7A data_rxb3 —

ASB7B data_rxb2 —

ASB7C data_rxb1 —

ASB7D data_rxb0 —

ASB8A data_rxb_par —

ASB8B data_rxb_spe —

ASB8C data_rxb_c1j1 —

ASB8D data_rxb_en —

ASB9A data_rxc7 —

ASB9B data_rxc6 —

ASB9C data_rxc5 —

ASB9D data_rxc4 —

ASB10A data_rxc3 —

ASB10B data_rxc2 —

Embedded

Core/FPGA

Interface

Site

FPGA Input

Signal

FPGA Output

Signal

ASB10C data_rxc1 —

ASB10D data_rxc0 —

ASB11A data_rxc_par prot_sw_c

ASB11B data_rxc_spe —

ASB11C data_rxc_c1j1 —

ASB11D data_rxc_en

ASB12A data_rxd7 —

ASB12B data_rxd6 —

ASB12C data_rxd5 —

ASB12D data_rxd4 —

ASB13A data_rxd3 —

ASB13B data_rxd2 —

ASB13C data_rxd1 —

ASB13D data_rxd0 —

ASB14A data_rxd_par line_fp

ASB14B data_rxd_spe sys_fp

ASB14C data_rxd_c1j1 —

ASB14D data_rxd_en —

ASB15A ﬁfosync_fp data_txa7

ASB15B — data_txa6

ASB15C — data_txa5

ASB15D — data_txa4

ASB16A — data_txa3

ASB16B — data_txa2

ASB16C — data_txa1

ASB16D — data_txa0

ASB17A — data_txb7

ASB17B — data_txb6

ASB17C — data_txb5

ASB17D — data_txb4

ASB18A — data_txb3

ASB18B — data_txb2

ASB18C — data_txb1

ASB18D — data_txb0

ASB19A — data_txa_par

ASB19B — data_txb_par

ASB19C — data_txc_par

ASB19D — data_txd_par

ASB20A — data_txc7

Lattice Semiconductor 67

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 42. Embedded Core/FPGA Interface Signal

Locations (continued)

Embedded

Core/FPGA

Interface

Site

FPGA Input

Signal

FPGA Output

Signal

ASB20B — data_txc6

ASB20C — data_txc5

ASB20D — data_txc4

ASB21A — data_txc3

ASB21B — data_txc2

ASB21C — data_txc1

ASB21D — data_txc0

ASB22A — data_txd7

ASB22B — data_txd6

ASB22C — data_txd5

ASB22D — data_txd4

ASB23A — data_txd3

ASB23B — data_txd2

ASB23C — data_txd1

ASB23D — data_txd0

ASB24A cpu_data_rx7 cpu_data_tx7

ASB24B cpu_data_rx6 cpu_data_tx6

ASB24C cpu_data_rx5 cpu_data_tx5

Embedded

Core/FPGA

Interface

Site

FPGA Input

Signal

FPGA Output

Signal

ASB24D cpu_data_rx4 cpu_data_tx4

ASB25A cpu_data_rx3 cpu_data_tx3

ASB25B cpu_data_rx2 cpu_data_tx2

ASB25C cpu_data_rx1 cpu_data_tx1

ASB25D cpu_data_rx0 cpu_data_tx0

ASB26A cpu_int_n cpu_addr6

ASB26B — cpu_addr5

ASB26C — cpu_addr4

ASB26D core_ready cpu_addr3

ASB27A — cpu_addr2

ASB27B — cpu_addr1

ASB27C — cpu_addr0

ASB27D — cpu_rd_wr_n

ASB28A cdr_clk_a cpu_cs_n

ASB28B cdr_clk_b —

ASB28C cdr_clk_c —

ASB28D cdr_clk_d —

BMLKCNTL fpga_sysclk —

Lattice Semiconductor 68

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Pin Information (continued)

The ORT4622 is pin compatible with a Series 3 OR3L125B device in the same package in terms of VDD, VSS, con-

ﬁguration, and special function pins. The uses and characteristics of the FPGA user I/O pins in the embedded core

area of the device have changed to support the ORT4622 functionality. Additionally, the lower-left programmable

clock manager (PCM) clock input pin (SECKLL) has been relocated. A "—" indicates the pin is not used and must

be left unconnected (cannot be tied to VDD or VSS).

Table 43. 432-Pin EBGA Pinout

Pin ORT4622 Pad Function

E4 PRD_CFGN RD_CFG

D3 PR1D I/O

D2 PR1C I/O

D1 PR1B I/O

F4 PR1A I/O

E3 PR2D I/O

E2 PR2C I/O

E1 PR2B I/O

F3 PR2A I/O

F2 PR3D I/O

F1 PR3C I/O

H4 PR3B I/O

G3 PR3A I/O-WR

G2 PR4D I/O

G1 PR4C I/O

J4 PR4B I/O

H3 VDD2VDD2

H2 PR5A I/O

J3 PR6C I/O

K4 PR6A I/O

J2 PR7A I/O-RD/MPI_STRB

J1 PR8D I/O

K3 PR8C I/O

K2 PR8B I/O

K1 PR8A I/O

L3 PR9D I/O

M4 PR9C I/O

L2 PR9B I/O

L1 PR9A I/O-CS0

M3 PR10D I/O

N4 PR10A I/O

M2 PR11D I/O

N3 PR11A I/O-CS1

N2 PR12D I/O

P4 PR12C I/O

N1 PR12A I/O

P3 PR13D I/O

P2 PR13C I/O

Pin ORT4622 Pad Function

P1 VDD2VDD2

R3 PR14D I/O

R2 PR14C I/O

R1 PR14B I/O

T2 PECKR I/O-ECKR

T4 PR15D I/O

T3 PR15C I/O

U1 PR15B I/O

U2 PR15A I/O

U3 PR16D I/O

V1 PR16B I/O

V2 PR16A I/O

V3 PR17D I/O

W1 PR17A I/O-M3

V4 PR18D I/O

W2 PR18B I/O

W3 PR18A I/O

Y2 — —

W4 PR19A M2

Y3 — —

AA1 — —

AA2 — —

Y4 — —

AA3 VDD2VDD2

AB1 — —

AB2 — —

AB3 — —

AC1 — M1

AC2 — —

AB4 — —

AC3 — —

AD2 — —

AD3 — —

AC4 — —

AE1 — db3 (core)

AE2 — db2 (core)

AE3 — db1 (core)

AD4 — db0 (core)

Lattice Semiconductor 69

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 43. 432-Pin EBGA Pinout (continued)

Pin ORT4622 Pad Function

AF1 — db7 (core)

AF2 — db6 (core)

AF3 — db5 (core)

AG1 — db4 (core)

AG2 VDD2VDD2

AG3 — int_n (core)

AF4 — —

AH1 — rst_n (core)

AH2 — M0

AH3 PPRGMN PRGM

AG4 PRESETN RESET

AH5 PDONE DONE

AJ4 — rd_wr_n (core)

AK4 — cs_n (core)

AL4 — addr0 (core)

AH6 — addr1 (core)

AJ5 — addr2 (core)

AK5 — addr3 (core)

AL5 — addr4 (core)

AJ6 — addr5 (core)

AK6 — addr6 (core)

AL6 — tstmux0s (core)

AH8 — tstmux1s (core)

AJ7 — tstmux2s (core)

AK7 — tstmux4s (core)

AL7 — tstmux7s (core)

AH9 — tstmux3s (core)

AJ8 VDD2VDD2

AK8 — tstmux6s (core)

AJ9 — tstmux5s (core)

AH10 — tstmux8s (core)

AK9 — INIT

AL9 — tstphase (core)

AJ10 — loopbken (core)

AK10 — exdnup (core)

AL10 — ecsel (core)

AJ11 — etoggle (core)

AH12 — resettn (core)

AK11 — mreset (core)

Pin ORT4622 Pad Function

AL11 — LDC

AJ12 — tstshftld (core)

AH13 — resetrn (core)

AK12 — tstclk (core)

AJ13 — bypass (core)

AK13 — tstmode (core)

AH14 — HDC

AL13 — —

AJ14 — —

AK14 — sys_clk (core)

AL14 — —

AJ15 VDD2VDD2

AK15 — sts_outd (core)

AL15 — sts_outdn (core)

AK16 — —

AH16 PECKB sts_outc (core)

AJ16 — sts_outcn (core)

AL17 — reslo (core)

AK17 — reshi (core)

AJ17 — —

AL18 — ref14 (core)

AK18 — ref10 (core)

AJ18 — rext (core)

AL19 — pll_VSSA (core)

AH18 — pll_VDDA (core)

AK19 — sts_outb (core)

AJ19 — sts_outbn (core)

AK20 — —

AH19 — sts_outa (core)

AJ20 — sts_outan (core)

AL21 VDD2VDD2

AK21 — ctap_refd (core)

AH20 — sts_ind (core)

AJ21 — sts_indn (core)

AL22 — sts_inc (core)

AK22 — sts_incn (core)

AJ22 — ctap_refc (core)

AL23 — sts_inb (core)

AK23 — sts_inbn (core)

7070 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 43. 432-Pin EBGA Pinout (continued)

Pin ORT4622 Pad Function

AH22 — ctap_refb (core)

AJ23 — sts_ina (core)

AK24 — sts_inan (core)

AJ24 — ctap_refa (core)

AH23 — —

AL25 — —

AK25 — —

AJ25 — lvds_en (core)

AH24 — scan_tstmd (core)

AL26 — scanen (core)

AK26 — dxp (core)

AJ26 — dxn (core)

AL27 VDD2vdd2

AK27 — sys_dobist (core)

AJ27 — sys_rssigo (core)

AH26 — bc (core)

AL28 — —

AK28 — —

AJ28 — —

AH27 — —

AG28 PCCLK CCLK

AH29 — —

AH30 — —

AH31 — —

AF28 — —

AG29 — —

AG30 — —

AG31 — —

AF29 — —

AF30 — —

AF31 — —

AD28 — —

AE29 VDD2VDD2

AE30 — —

AE31 — —

AC28 — —

AD29 — —

AD30 — —

AC29 — —

AB28 — —

Pin ORT4622 Pad Function

AC30 — —

AC31 — —

AB29 — —

AB30 — —

AB31 — —

AA29 — —

Y28 — —

AA30 — —

AA31 — —

Y29 — MPI_IRQ

W28 — —

Y30 PL18A I/O-SECKLL

W29 PL18C I/O

W30 PL18D I/O

V28 PL17A I/O-MPI_BI

W31 PL17C I/O

V29 PL17D I/O

V30 PL16A I/O

V31 PL16C I/O

U29 PL16D I/O

U30 PL15A I/O-MPI_RW

U31 PL15B I/O

T30 VDD2VDD2

T28 PL15D I/O

T29 PL14A I/O-MPI_CLK

R31 PL14B I/O

R30 PL14C I/O

R29 PECKL I/O-ECKL

P31 PL13A I/O

P30 PL13D I/O

P29 PL12A I/O

N31 PL12C I/O

P28 PL12D I/O

N30 PL11A I/O-A4

N29 PL11C I/O

M30 PL11D I/O

N28 PL10A I/O

M29 PL10C I/O

L31 VDD2VDD2

L30 PL9A I/O-A3

Lattice Semiconductor 71

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 43. 432-Pin EBGA Pinout (continued)

Pin ORT4622 Pad Function

M28 PL9B I/O

L29 PL9C I/O

K31 PL9D I/O

K30 PL8A I/O-A2

K29 PL8B I/O

J31 PL8C I/O

J30 PL8D I/O

K28 PL7D I/O-A1/MPI_BE1

J29 PL6B I/O

H30 PL6C I/O

H29 PL6D I/O

J28 PL5D I/O

G31 PL4B I/O

G30 PL4C I/O

G29 VDD2VDD2

H28 PL3A I/O

F31 PL3B I/O

F30 PL3C I/O

F29 PL3D I/O

E31 PL2A I/O

E30 PL2B I/O

E29 PL2C I/O

F28 PL2D I/O-A0/MPI_BE0

D31 PL1A I/O

D30 PL1B I/O

D29 PL1C I/O

E28 PL1D I/O

D27 PRD_DATA RD_DATA/TDO

C28 PT1A I/O-TCK

B28 PT1B I/O

A28 PT1C I/O

D26 PT1D I/O

C27 PT2A I/O

B27 PT2B I/O

A27 PT2C I/O

C26 PT2D I/O

B26 PT3A I/O

A26 PT3B I/O

D24 PT3C I/O

Pin ORT4622 Pad Function

C25 PT3D I/O

B25 PT4A I/O-TMS

A25 PT4B I/O

D23 PT4C I/O

C24 PT4D I/O

B24 VDD2VDD2

C23 PT5B I/O

D22 PT5C I/O

B23 PT5D I/O

A23 PT6A I/O-TDI

C22 PT6D I/O

B22 PT7A I/O

A22 PT7D I/O

C21 PT8A I/O

D20 PT8D I/O

B21 PT9A I/O

A21 PT9D I/O

C20 PT10A I/O-DOUT

D19 PT10D I/O

B20 PT11A I/O

C19 PT11C I/O

B19 PT11D I/O

D18 PT12A I/O-D0/DIN

A19 PT12C I/O

C18 PT12D I/O

B18 PT13A I/O

A18 PT13C I/O

C17 PT13D I/O-D1

B17 PT14A I/O-D2

A17 VDD2VDD2

B16 PT14C I/O

D16 PT14D I/O

C16 PT15A I/O-D3

A15 PT15B I/O

B15 PT15C I/O

C15 PECKT I/O-ECKT

A14 PT16A I/O-D4

B14 PT16B I/O

C14 PT16D I/O

7272 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 43. 432-Pin EBGA Pinout (continued)

Pin ORT4622 Pad Function

A13 PT17A I/O

D14 PT17B I/O

B13 PT17D I/O

C13 PT18A I/O-D5

B12 PT18B I/O

D13 VDD2VDD2

C12 PT19A I/O

A11 PT19D I/O

B11 PT20A I/O

D12 PT20D I/O-D6

C11 PT21A I/O

A10 PT21D I/O

B10 PT22D I/O

C10 PT23B I/O

A9 PT23C I/O

B9 VDD2VDD2

D10 PT24A I/O

C9 PT24B I/O

B8 PT24C I/O

C8 PT24D I/O-D7

D9 PT25A I/O

A7 PT25B I/O

B7 PT25C I/O

C7 PT25D I/O

D8 PT26A I/O

A6 PT26B I/O

B6 PT26C I/O

C6 PT26D I/O

A5 PT27A I/O-RDY/RCLK

B5 PT27B I/O

C5 PT27C I/O

D6 PT27D I/O

A4 PT28A I/O

B4 PT28B I/O

C4 PT28C I/O

D5 PT28D I/O-SECKUR

A12 VSS VSS

A16 VSS VSS

A2 VSS VSS

A20 VSS VSS

A24 VSS VSS

A29 VSS VSS

Pin ORT4622 Pad Function

A3 VSS VSS

A30 VSS VSS

A8 VSS VSS

AD1 VSS VSS

AD31 VSS VSS

AJ1 VSS VSS

AJ2 VSS VSS

AJ30 VSS VSS

AJ31 VSS VSS

AK1 VSS VSS

AK29 VSS VSS

AK3 VSS VSS

AK31 VSS VSS

AL12 VSS VSS

AL16 VSS VSS

AL2 VSS VSS

AL20 VSS VSS

AL24 VSS VSS

AL29 VSS VSS

AL3 VSS VSS

AL30 VSS VSS

AL8 VSS VSS

B1 VSS VSS

B29 VSS VSS

B3 VSS VSS

B31 VSS VSS

C1 VSS VSS

C2 VSS VSS

C30 VSS VSS

C31 VSS VSS

H1 VSS VSS

H31 VSS VSS

M1 VSS VSS

M31 VSS VSS

T1 VSS VSS

T31 VSS VSS

Y1 VSS VSS

Y31 VSS VSS

A1 VDD VDD

A31 VDD VDD

AA28 VDD VDD

AA4 VDD VDD

Lattice Semiconductor 73

Preliminary Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Pin Information (continued)

Table 43. 432-Pin EBGA Pinout (continued)

Pin ORT4622 Pad Function

AE28 VDD VDD

AE4 VDD VDD

AH11 VDD VDD

AH15 VDD VDD

AH17 VDD VDD

AH21 VDD VDD

AH25 VDD VDD

AH28 VDD VDD

AH4 VDD VDD

AH7 VDD VDD

AJ29 VDD VDD

AJ3 VDD VDD

AK2 VDD VDD

AK30 VDD VDD

AL1 VDD VDD

AL31 VDD VDD

B2 VDD VDD

B30 VDD VDD

Pin ORT4622 Pad Function

C29 VDD VDD

C3 VDD VDD

D11 VDD VDD

D15 VDD VDD

D17 VDD VDD

D21 VDD VDD

D25 VDD VDD

D28 VDD VDD

D4 VDD VDD

D7 VDD VDD

G28 VDD VDD

G4 VDD VDD

L28 VDD VDD

L4 VDD VDD

R28 VDD VDD

R4 VDD VDD

U28 VDD VDD

U4 VDD VDD

7474 Lattice Semiconductor

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/

Package Thermal Characteristics

Summary

There are three thermal parameters that are in com-

mon use: ΘJA, ψJC, and ΘJC. It should be noted that all

the parameters are affected, to varying degrees, by

package design (including paddle size) and choice of

materials, the amount of copper in the test board or

system board, and system airﬂow.

ΘΘ

ΘΘJA

This is the thermal resistance from junction to ambient

(theta-JA, R-theta, etc.).

where TJ is the junction temperature, TA is the ambient

air temperature, and Q is the chip power.

Experimentally, ΘJA is determined when a special ther-

mal test die is assembled into the package of interest,

and the part is mounted on the thermal test board. The

diodes on the test chip are separately calibrated in an

oven. The package/board is placed either in a JEDEC

natural convection box or in the wind tunnel, the latter

for forced convection measurements. A controlled

amount of power (Q) is dissipated in the test chip’s

heater resistor, the chip’s temperature (TJ) is deter-

mined by the forward drop on the diodes, and the ambi-

ent temperature (TA) is noted. Note that ΘJA is

expressed in units of °C/watt.

ψψ

ψψJC

This JEDEC designated parameter correlates the junc-

tion temperature to the case temperature. It is generally

used to infer the junction temperature while the device

is operating in the system. It is not considered a true

thermal resistance, and it is deﬁned by:

where TC is the case temperature at top dead center,

TJ is the junction temperature, and Q is the chip power.

During the ΘJA measurements described above,

besides the other parameters measured, an additional

temperature reading, TC, is made with a thermocouple

attached at top-dead-center of the case. ψJC is also

expressed in units of °C/W.

ΘΘ

ΘΘJC

This is the thermal resistance from junction to case. It

is most often used when attaching a heat sink to the

top of the package. It is deﬁned by:

The parameters in this equation have been deﬁned

above. However, the measurements are performed

with the case of the part pressed against a water-

cooled heat sink to draw most of the heat generated by

the chip out the top of the package. It is this difference

in the measurement process that differentiates ΘJC

from ψJC. ΘJC is a true thermal resistance and is

expressed in units of °C/W.

ΘΘ

ΘΘJB

This is the thermal resistance from junction to board

(ΘJL). It is deﬁned by:

where TB is the temperature of the board adjacent to a

lead measured with a thermocouple. The other param-

eters on the right-hand side have been deﬁned above.

This is considered a true thermal resistance, and the

measurement is made with a water-cooled heat sink

pressed against the board to draw most of the heat out

of the leads. Note that ΘJB is expressed in units of

°C/W, and that this parameter and the way it is mea-

sured are still in JEDEC committee.

FPGA Maximum Junction Temperature

Once the power dissipated by the FPGA has been

determined (see the Estimating Power Dissipation sec-

tion), the maximum junction temperature of the FPGA

can be found. This is needed to determine if speed der-

ating of the device from the 85 °C junction temperature

used in all of the delay tables is needed. Using the

maximum ambient temperature, TAmax, and the power

dissipated by the device, Q (expressed in °C), the max-

imum junction temperature is approximated by:

TJmax = TAmax + (Q • ΘJA)

Table 44 lists the thermal characteristics for all pack-

ages used with the

ORCA

ORT4622 Series of FPGAs.

ΘJA TJTA–

--------------------

ψJC TJTC–

--------------------

ΘJC TJTC–

--------------------

ΘJB TJTB–

--------------------

Lattice Semiconductor 75

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Package Thermal Characteristics

Table 44

. ORCA

ORT4622 Plastic Package Thermal Guidelines

Package Coplanarity

The coplanarity limits of the

ORCA

Series 3/3+ packages are as follows:

■EBGA: 8.0 mils

Package Parasitics

The electrical performance of an IC package, such as signal quality and noise sensitivity, is directly affected by the

package parasitics. Table 45 lists eight parasitics associated with the

ORCA

packages. These parasitics represent

the contributions of all components of a package, which include the bond wires, all internal package routing, and

the external leads.

Four inductances in nH are listed: LSW and LSL, the self-inductance of the lead; and LMW and LML, the mutual

inductance to the nearest neighbor lead. These parameters are important in determining ground bounce noise and

inductive crosstalk noise. Three capacitances in pF are listed: CM, the mutual capacitance of the lead to the near-

est neighbor lead; and C1 and C2, the total capacitance of the lead to all other leads (all other leads are assumed

to be grounded). These parameters are important in determining capacitive crosstalk and the capacitive loading

effect of the lead. Resistance values are in mΩ.

The parasitic values in Table 45 are for the circuit model of bond wire and package lead parasitics. If the mutual

capacitance value is not used in the designer’s model, then the value listed as mutual capacitance should be added

to each of the C1 and C2 capacitors.

Package

ΘΘ

ΘΘJA (°C/W) T = 70 °C Max

TJ = 125 °C Max

0 fpm (W)

0 fpm 200 fpm 500 fpm

432-Pin EBGA 11 8.5 5 5

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

76 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Package Parasitics (continued)

Table 45.

ORCA

ORT4622 Package Parasitics

5-3862(C)r2

Figure 34. Package Parasitics

Package Type LSW LMW RWC1C2CMLSL LML

432-Pin EBGA 4 1.5 500 1.0 1.0 0.3 3—5.5 0.5—1

PAD N

CIRCUIT

BOARD PAD

PAD N + 1

Lattice Semiconductor 77

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Package Outline Diagram

Terms and Deﬁnitions

Basic Size (BSC): The basic size of a dimension is the size from which the limits for that dimension are derived

by the application of the allowance and the tolerance.

Design Size: The design size of a dimension is the actual size of the design, including an allowance for ﬁt

and tolerance.

Typical (TYP): When speciﬁed after a dimension, this indicates the repeated design size if a tolerance is

speciﬁed or repeated basic size if a tolerance is not speciﬁed.

Reference (REF): The reference dimension is an untoleranced dimension used for informational purposes only.

It is a repeated dimension or one that can be derived from other values in the drawing.

Minimum (MIN) or

Maximum (MAX): Indicates the minimum or maximum allowable size of a dimension.

ORCA

ORT4622 FPSC Data Sheet

Four-Channel x 622 Mbits/s Backplane Transceiver July 2009

78 Lattice Semiconductor

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Package Outline Diagram (continued)

432-Pin EBGA

Dimensions are in millimeters.

5-4406(F)

0.91 ± 0.06 1.54 ± 0.13

SEATING PLANE

SOLDER BALL

0.63 ± 0.07

0.20

40.00 ± 0.10

40.00

A1 BALL

3026

282422

23 257

312915 21

32711 17

4 6 8 10 12 14 162

9131

30 SPACES @ 1.27 = 38.10

30 SPACES

A1 BALL

0.75 ± 0.15

IDENTIFIER ZONE

± 0.10

@ 1.27 = 38.10

CORNER

Lattice Semiconductor 79

Data Sheet

ORCA

ORT4622 FPSC

July 2009 Four-Channel x 622 Mbits/s Backplane Transceiver

Discontinued Product (PCN#03-08). Contact Rochester Electronics for Availability.

www.latticesemi.com/sales/discontinueddevicessales.cfm

Ordering Information

Table 46. Ordering Information

Device Family Part Number Package

Type

Ball

Count Grade Packing

Designator

ORT4622 ORT4622BC432-DB EBGA 432 C DB

Device Family

ORT4622

ORT4622 XXX XX

XXX

Packing Designator

DB = Dry Packed Tray

Package Type

BC = Enhanced Ball Grid Array (EBGA) Ball Count

432

Grade

Blank = Industrial