www.fairchildsemi.com RC4136 General Performance Quad 741 Operational Amplifier Features * * * * * * * * Unity gain bandwidth - 3 MHz Short circuit protection No frequency compensation required No latch-up Large common mode and differential voltage ranges Low power consumption Parameter tracking over temperature range Gain and phase match between amplifiers Description The RC4136 is made up of four 741 type independent high gain operational amplifiers internally compensated and constructed on a single silicon chip using the planar epitaxial process. of the RC4136 quad amplifier in all 741 operational amplifier applications providing the highest possible packaging density. This amplifier meets or exceeds all specifications for 741 type amplifiers. Excellent channel separation allows the use The specially designed low noise input transistors allow the RC4136 to be used in low noise signal processing applications such as audio preamplifiers and signal conditioners. Block Diagram Pin Assignments -Input (A) +Input (A) A + D + Output (A) Output (C) + B + -Input (B) +Input (D) Output (D) Output (B) +Input (B) -Input (D) C -Input (A) +Input (A) Output (A) Output (B) +Input (B) -Input (B) -VS 1 14 2 13 3 12 4 11 5 10 6 9 7 8 -Input (D) +Input (D) Output (D) +VS Output (C) +Input (C) -Input (C) +Input (C) 65-4136-02 -Input (C) 65-4136-01 Rev. 1.0.0 PRODUCT SPECIFICATION RC4136 Absolute Maximum Ratings (beyond which the device may be damaged)1 Parameter Min Max Units RC4136 18 V RM4136 22 V Input Voltage 30 V Differential Input Voltage 30 V SOIC 300 mW PDIP 468 mW Supply Voltage Typ 2 Output Short Circuit Duration3 PDTA < 50C Indefinite CerDIP Operating Temperature 1042 mW RC4136 0 70 C RM4136 -55 125 C -65 150 C 125 C CerDIP 175 C DIP 300 C SOIC 260 C Storage Temperature Junction Temperature Lead Soldering Temperature (60 seconds) SOIC, PDIP Notes: 1. Functional operation under any of these conditions is NOT implied. Performance and reliability are guaranteed only if Operating Conditions are not exceeded. 2. For supply voltages less than 15V, the absolute maximum input voltage is equal to the supply voltage. 3. Short circuit may be to ground, typically 45 mA. Operating Conditions Parameter qJC Thermal resistance qJA Thermal resistance For TA > 50C Derate at 2 Min Typ Max Units 60 C/W SOIC 200 C/W PDIP 160 C/W CerDIP 120 C/W SOIC 5.0 mW/C RC4136 PRODUCT SPECIFICATION Electrical Characteristics (VS = 15V and TA = +25C, unless otherwise noted) RM4136 Parameters Test Conditions Input Offset Voltage RS 10kW RC4136 Typ Max 0.5 Input Offset Current Input Bias Current Input Resistance Min Min Typ Max Units 5.0 0.5 6.0 mV 5.0 200 5.0 200 nA 40 500 40 500 nA 0.3 5.0 0.3 5.0 MW Large Signal Voltage Gain RL 2kW, VOUT = 10V 50 300 20 300 V/mV Output Voltage Swing RL 10kW 12 14 12 14 V RL 2kW 10 13 10 13 12 14 12 14 V Input Voltage Range Common Mode Rejection Ratio RS 10kW 70 100 70 100 dB Power Supply Rejection Ratio RS 10kW 76 100 76 100 dB Power Consumption RL = , All Outputs 210 Rise Time VIN = 20mV, RL = 2kW 0.13 0.13 mS Overshoot CL 100pF 5.0 5.0 % 3.0 3.0 MHz 340 210 340 mW Transient Response Unity Gain Bandwidth Slew Rate RL 2kW 1.5 1.0 V/mS Channel Separation F = 1.0kHz, RS =1kW 90 90 dB Electrical Characteristics (RM = -55C TA = 125, RC = 0C TA = 70, VS = 15V) RM4136 Parameters Test Conditions Input Offset Voltage RS 10kW Min Typ RC4136 Max Min Typ Max Units 6.0 7.5 mV Input Offset Current 500 300 nA Input Bias Current 1500 800 nA Large Signal Voltage Gain RL 2kW, VOUT = 10V 25 15 V/mV Output Voltage Swing RL 2kW 10 10 V Power Consumption 240 400 240 400 mW 3 PRODUCT SPECIFICATION RC4136 Electrical Characteristics Comparison (VS = 15V and TA +25C unless otherwise noted) Parameter RC4136 (Typ.) RC741 (Typ.) LM324 (Typ.) Units Input Offset Voltage 0.5 2.0 2.0 mV Input Offset Current 5.0 10 5.0 nA Input Bias Current 40 80 55 nA Input Resistance 5.0 2.0 Large Signal Voltage Gain (RL = 2kW) MW 300 200 100 V/mV Output Voltage Swing (RL= 2kW) 13V 13V |+VS - 1.2V| to -VS V Input Voltage Range 14V 13V |+VS - 1.5V| to -VS V Common Mode Rejection Ratio 100 90 85 dB Power Supply Rejection Ratio 100 90 100 dB Rise Time 0.13 0.3 mS Overshoot 5.0 5.0 % Unity Gain Bandwidth 3.0 0.8 0.8 Slew Rate 1.0 0.5 0.5 Input Noise Voltage Density (F= 1kHz) 10 22.5 nV/OHz Short Circuit Current 45 25 mA Transient Response 4 MHz V/mS RC4136 PRODUCT SPECIFICATION Typical Performance Characteristics 25 100 VS = 20 15V IOS (nA) 65-4136-03 40 20 0 0 +10 +20 +30 +40 +50 +60 15V 15 10 5 0 +70 0 +10 +20 TA (C) +40 +50 +60 +70 TA (C) Figure 1. Input Bias Current vs. Temperature Figure 2. Input Offset Current vs. Temperature 15 15 10 T A = +25 C 10 T A = +25 C 5 VOUT (V) 5 0 -5 65-4136-05 VCM (V) +30 -10 -15 4 6 8 10 12 14 16 0 -5 RL = 2 k W -10 -15 4 18 65-4136-06 IB (nA) 60 VS = 65-4136-04 80 6 8 10 12 14 16 18 +VS/-VS (V) VS (V) Figure 3. Input Common Mode Voltage Range vs. Supply Voltage Figure 4. Output Voltage vs. Supply Voltage 800K 240 VS = 15V VS = 15V RL = 2 k W 200K 0 0 +10 +20 +30 +40 +50 +60 TA (C) Figure 5. Open Loop Gain vs. Temperature +70 200 180 65-4136-08 400K PC (mW) 220 65-4136-07 AVOL (V/mV) 600K 160 0 +10 +20 +30 +40 +50 +60 +70 TA (C) Figure 6. Power Consumption vs. Temperature 5 PRODUCT SPECIFICATION RC4136 Typical Performance Characteristics (continued) 120 40 36 32 28 24 20 16 12 8 4 0 100 VOUT P-P (V) 60 40 65-4136-09 20 0 -20 1 10 100 1K 10K 100K 1M 10M VS = 15V T A = +25 C RL = 2 k W 1K 10K F (Hz) 10 TA = +25C VS = 15V TA = +25 C IQ (mA) 8 1.0 6 4 65-4136-12 28 26 24 22 20 18 16 14 12 10 8 0.1 2 0 10 0 3 6 9 12 15 18 +VS/-VS (V) RL (kW) Figure 9. Output Voltage Swing vs. Load Resistance Figure 10. Quiescent Current vs. Supply Voltage 28 10 8 6 4 2 0 -2 -4 -6 -8 -10 24 VS = 15V TA = +25 C 20 VOUT (mV) Output Input 65-4136-13 VOUT (V) 1M Figure 8. Output Voltage Swing vs. Frequency 65-4136-11 VOUT P-P (V) Figure 7. Open Loop Gain vs. Frequency 0 10 20 30 Time (S) 40 Figure 11. Follower Large Signal Pulse Response 6 100K F (Hz) 16 12 VS = 15V T A = +25 C RL = 2 k W C L = 100 pF 90% 8 4 65-4136-14 AVOL (dB) 80 65-4136-10 100 10% Rise Time 0 0 0.25 0.50 0.75 1.00 1.25 Time (S) Figure 12. Transient Response Output Voltage vs. Time RC4136 PRODUCT SPECIFICATION Typical Performance Characteristics (continued) 0.6 100 0.5 THD (%) 120 80 60 0.4 0.3 VS = 15V TA = +25 C 100 1K 10K 65-4136-16 0 10 65-4136-15 20 VOUT = 1 VRMS VS = 30V 0.2 40 0.1 0 10 100K 100 1K 10K 100K F (Hz) F (Hz) Figure 13. Channel Separation vs. Frequency 0.6 Figure 14. Total Harmonic Distortion vs. Frequency VS = 15V R L = 2K A V = 40 dB f = 1 kHz RS = 1k W 0.5 THD (%) 0.4 0.3 0.2 65-4136-17 CS (dB) 140 0.1 0 1 2 3 4 5 6 7 8 9 10 VOUT (V RMS ) Figure 15. Total Harmonic Distortion vs. Output Voltage 7 PRODUCT SPECIFICATION RC4136 RC4136 Versus LM324 Although the LM324 is an excellent device for single-supply applications where ground sensing is important, it is a poor substitute for four 741s in split supply circuits. The simplified input circuit of the RC4136 exhibits much lower noise than that of the LM324 and exhibits no crossover distortion as compared with the LM324 (see Figure 16). The LM324 shows significant crossover distortion and pulse delay in attempting to handle a large signal input pulse. 324 4136 F = 10 kHz VOUT = 8 VP-P F = 50 kHz V OUT = 8 V P-P RL = 2 k W AV= 1 VS = 5V 65-4136-18 120 741 324 1K 10K 100K 4136 80 4136 741 60 40 1M Figure 17. Output Voltage Swing vs. Frequency 65-4136-20 20 F (Hz) 8 100 VS = 15V T A = +25 C R L = 2 kW AVOL (dB) 40 36 32 28 24 20 16 12 8 4 0 100 65-4136-19 VOUT P-P (V) Figure 16. Comparative Crossover Distortion 0 -20 1 10 100 1K 10K 100K 1M F (Hz) Figure 18. Open Loop Gain vs. Frequency 10M RC4136 PRODUCT SPECIFICATION RC4136 Versus LM324 (continued) +8 16 4136 +2 Outputs 0 324 -2 Input 65-4136-21 -4 -6 -8 30 0 40 60 0 C = T A < +70 C 12 +VCM (V) VOUT (V) +4 14 Vs = 10V RL = 2 kW 80 10 741 8 4136 6 4 65-4136-22 +6 2 0 5 10 Time (S) 20 15 +VS/-VS (V) Figure 19. Follower Large Signal Pulse Response Output Voltage vs. Time Figure 20. Input Common Mode Voltage Range vs. Supply Voltage Typical Applications +Vs 910K +Vs +Vs 1 1 2 4136A 100W 3 4136A 100K 3 2 VOUT 91K 5K 100K AV = 10 65-0520 +VIN Figure 21. Lamp Driver Figure 22. Power Amplifier VIN 1 VIN 2 4136A 2 10K 3 65-0523 VOUT 65-0519 Figure 23. Voltage Follower +VREF 1 4136A 3 VOUT 10M 65-0522 Figure 24. Comparator with Hysteresis 9 PRODUCT SPECIFICATION RC4136 Typical Applications (continued) +Vs VIN 0.01F 16K 100K VOUT 0.001F 1 16K 1 0.01F 2 4136A 3 4136A 3 VoUT 2 +Vs 100K 100K 1 0 100K 100K 100K 65-0527 65-0521 Figure 25. DC Coupled 1kHz Lowpass Active Filter VIN Figure 26. Squarewave Oscillator 0.01 F 390K 120K 0.01 F +Vs 1 620K 620W VoUT 390K +Vs 4136A 3 39K 6 2 4 4136B 5 10 F 100K 100K +Vs 65-0526 Figure 27. 1kHz Bandpass Active Filter 1M 100K +Vs +Vs 1 VIN 2 4136A 3 10K VIN VoUT +Vs 100K 100K 1 2 4136A 3 VoUT 10K 100K 0.1 F 10 F 100K +Vs 10 F 10K 100K 10K 65-0525 65-0524 Figure 28. AC Coupled Non-Inverting Amplifier 10 Figure 29. AC Coupled Inverting Amplifier RC4136 PRODUCT SPECIFICATION Typical Applications (continued) 0.05 F R 100K 100K 1 +VC* 51K 2 4136A 51K 3 6 5 4 Output 1 V+/210K 51K R/2 50K 4136B Output 2 10K 65-0528 * Wide control voltage range: 0V < Vc < 2(+Vs -1.5V) Figure 30. Voltage Control Oscillator (VCO) 2.5K Cal 20K 1% 20K 1% DC Output 20K 1% 4.7 F AC Input 20K 1% 10K 1% 4.7 F D1 FD666 1 2 4136A D2 FD666 4.7 F 6 3 5 4136B 4 5.1K 10K 65-0531 Figure 31. Full-Wave Rectifier and Averaging Filter R2 30K 10K 1 4136A 3 2 1K Trim R, such that R3 15K R1 R3 = R2 2R4 6 C1 5 R4 7.5K 741 Output 4136B 4 100 R4 7.5K 10 0.0001 C2 1 F 65-0529 Figure 32. Notch Filter Using the RC4136 as a Gyrator 65-0530 Input C1 ( mF) R1 30K 0.001 0.001 0.01 1.0 Center Frequency (Hz) Figure 33. Notch Frequency vs. C1 11 PRODUCT SPECIFICATION RC4136 Typical Applications (continued) 2 V IN 1 V4 4136A 3 VIN < V4 Q1 5 6 4136B V3 4 V3 < VIN < V4 Q2 9 8 V2 4136C 10 V2 < V IN < V3 Q3 13 V1 14 4136D 12 V IN < V1 65-0532 Figure 34. Multiple Aperture Window Discriminator (-) 2 1 4136A 3 R1 45K 1% R3 10K 1% Inputs (+) 5 6 4136B 4136C VOUT * Matching determines CMRR 10 Av = R5* 10K 0.1% 4 R1 = R4 R2 = R5 R6 = R7 R4 45K 1% 8 9 R6* 100K 0.1% R2 10K 0.1% R6 ( 1 + 2R1 ) R2 R3 R7* 100K 0.1% 65-0533 Figure 35. Differential Input Instrumentation Amplifier with High Common Mode Rejection 12 RC4136 PRODUCT SPECIFICATION Typical Applications (continued) +15V 10K 10K VIN1 D4 IN457 Q1* 10K 10K 1 2 1K 3 4136A 6 D1 1N457 10K 4 4136B 5 VoUT = (VIN1) (VIN2) VIN3 10K Q4* Q2* V IN2 10K Q3* 1K 10 9 10K 14 8 12 4136C 1K D2 1N457 10K 4136D VIN3 13 D3 1N457 10K 65-0534 *Matched Transistors Figure 36. Analog Multiplier/Divider DC-1Hz N Out 3.3M 49.9K 0.082 F 100K 49.9W 1.0 F 2 DUT 100K 49.9W 499K Compensate as Required 1 4136A 499K 3 60 dB Wideband Amplifier 78.7K 10 F 1 Hz 499W 1 F 1000 F 0.1 F 0.01 F 1 kHz 10 F 1 Hz 3.16K 1 Hz 3.16K 499K 10K Spot Noise Out 1 F 8 10 6 31.6K 4136C 4 9 4136B 0.1 F 5 100K 1mV = 1nV/ Hz RMS 499W 0.01 F 1 kHz 499K Stepped 10 dB Attenuator 1 kHz Selectable Frequency Constant Q Filter 65-0535 Figure 37. Spot Noise Measurement Test Circuit 13 RC4136 PRODUCT SPECIFICATION Simplified Schematic Diagram +Vs (11) R1 8.7K Q10 Q5 Q6 Q14 (1,6,8,14) -Input Q13 Q2 Q1 R6 50 R8 100 Output (3,4,10,12) Q12 +Input D1 (2,5,9,13) R7 50 R5 50K Q15 Q7 Q8 15 pF Q9 Q3 Q4 Q11 R9 15K R2 5K C1 30 pF R3 5K Z1 5.5V R4 50K -Vs (7) 65-0495 14 RC4136 PRODUCT SPECIFICATION Mechanical Dimensions 14-Lead Ceramic DIP Package Inches Symbol Min. A b1 b2 c1 D E e eA L Q s1 a Millimeters Max. -- .200 .014 .023 .045 .065 .008 .015 -- .785 .220 .310 .100 BSC .300 BSC .125 .200 .015 .060 .005 -- 90 105 Min. Notes: Notes Max. -- 5.08 .36 .58 1.14 1.65 .20 .38 -- 19.94 5.59 7.87 2.54 BSC 7.62 BSC 3.18 5.08 .38 1.52 .13 -- 90 105 1. Index area: a notch or a pin one identification mark shall be located adjacent to pin one. The manufacturer's identification shall not be used as pin one identification mark. 8 2 2. The minimum limit for dimension "b2" may be .023 (.58mm) for leads number 1, 7, 8 and 14 only. 8 4 3. Dimension "Q" shall be measured from the seating plane to the base plane. 4 5, 9 7 4. This dimension allows for off-center lid, meniscus and glass overrun. 3 6 5. The basic pin spacing is .100 (2.54mm) between centerlines. Each pin centerline shall be located within .010 (.25mm) of its exact longitudinal position relative to pins 1 and 14. 6. Applies to all four corners (leads number 1, 7, 8, and 14). 7. "eA" shall be measured at the center of the lead bends or at the centerline of the leads when "a" is 90. 8. All leads - Increase maximum limit by .003 (.08mm) measured at the center of the flat, when lead finish applied. 9. Twelve spaces. D 7 1 8 14 NOTE 1 E s1 eA e A Q L b2 a c1 b1 15 PRODUCT SPECIFICATION RC4136 Mechanical Dimensions (continued) 14-Lead Plastic DIP Package Inches Symbol Millimeters Min. Max. Min. Max. A A1 A2 -- .015 .115 .210 -- .195 -- .38 2.93 5.33 -- 4.95 B B1 C D D1 E E1 e eB .014 .022 .045 .070 .008 .015 .725 .795 .005 -- .300 .325 .240 .280 .100 BSC -- .430 .115 .200 14 L N .36 .56 1.14 1.78 .20 .38 18.42 20.19 .13 -- 7.62 8.26 6.10 7.11 2.54 BSC -- 10.92 2.92 5.08 14 Notes: Notes 1. Dimensioning and tolerancing per ANSI Y14.5M-1982. 2. "D" and "E1" do not include mold flashing. Mold flash or protrusions shall not exceed .010 inch (0.25mm). 3. Terminal numbers are shown for reference only. 4. "C" dimension does not include solder finish thickness. 5. Symbol "N" is the maximum number of terminals. 4 2 2 5 D 7 1 8 14 E1 D1 E e A A1 C L B1 16 B eB RC4136 PRODUCT SPECIFICATION Mechanical Dimensions (continued) 14-Lead SOIC Package Inches Symbol Min. A A1 B C D E e H h L N a ccc Millimeters Max. Min. Max. .053 .069 .004 .010 .013 .020 .008 .010 .336 .345 .150 .158 .050 BSC .228 .244 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 8.54 8.76 3.81 4.01 1.27 BSC 5.79 6.20 .010 .016 0.25 0.40 .020 .050 14 0.50 1.27 14 0 8 0 8 -- .004 -- 0.10 14 Notes: Notes 1. Dimensioning and tolerancing per ANSI Y14.5M-1982. 2. "D" and "E" do not include mold flash. Mold flash or protrusions shall not exceed .010 inch (0.25mm). 3. "L" is the length of terminal for soldering to a substrate. 4. Terminal numbers are shown for reference only. 5 2 2 5. "C" dimension does not include solder finish thickness. 6. Symbol "N" is the maximum number of terminals. 3 6 8 E 1 H 7 h x 45 D C A1 A e B SEATING PLANE -C- LEAD COPLANARITY a L ccc C 17 PRODUCT SPECIFICATION RC4136 Ordering Information Product Number Temperature Range Screening Package Package Marking RC4136N 0 to 70C Commercial 14 Pin Plastic DIP RC4136N RC4136M 0 to 70C Commercial 14 Pin Narrow SOIC RC4136M RM4136D -55C to +125C RM4136D/8831 -55C to +125C 14 Pin Ceramic DIP Military 14 Pin Ceramic DIP Note: 1. /883 denotes MIL-STD-883, Par. 1.2.1 compliant device. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 5/20/98 0.0m 001 Stock#DS30004136 O 1998 Fairchild Semiconductor Corporation