AAT2120 500mA Low Noise Step-Down Converter General Description Features The AAT2120 SwitchReg is a 1.8MHz step-down converter with an input voltage range of 2.7V to 5.5V and output as low as 0.6V. Its low supply current, small size, and high switching frequency make the AAT2120 the ideal choice for portable applications. * * * * * * * * * The AAT2120 delivers up to 500mA of load current, while maintaining a low 45A no load quiescent current. The 1.8MHz switching frequency minimizes the size of external components, while keeping switching losses low. The AAT2120 feedback and control delivers excellent load regulation and transient response with a small output inductor and capacitor. * * * * * The AAT2120 maintains high efficiency throughout the load range. The AAT2120's unique architecture produces reduced ripple and spectral noise. Overtemperature and short-circuit protection safeguard the AAT2120 and system components from damage. SwitchRegTM VIN Range: 2.7V to 5.5V VOUT Range: 0.6V to VIN Up to 500mA Output Current Up to 96% Efficiency Low Noise Light Load Mode 45A Typical Quiescent Current 1.8MHz Switching Frequency Soft-Start Control Over-Temperature and Current Limit Protection 100% Duty Cycle Low-Dropout Operation <1A Shutdown Current Small External Components Ultra-Small STDFN22-8 Package Temperature Range: -40C to +85C Applications The AAT2120 is available in a Pb-free, 8-pin, 2x2mm STDFN package and is rated over the -40C to +85C temperature range. * * * * * * * Bluetooth(R) Headsets Cellular Phones Digital Cameras Handheld Instruments Micro Hard Disk Drive Portable Music Players USB Devices Typical Application VIN VO = 1.8V AAT2120 VP LX VIN C1 4.7F EN GND 2120.2007.10.1.1 FB PGND 500mA L1 3.0H R1 118k R2 59k C2 4.7F 1 AAT2120 500mA Low Noise Step-Down Converter Pin Descriptions Pin # Symbol 1 VP 2 3 4 5 6 7 VIN GND FB N/C EN LX 8 PGND EP Function Input power pin; connected to the source of the P-channel MOSFET. Connect to the input capacitor. Input bias voltage for the converter. Non-power signal ground pin. Feedback input pin. Connect this pin to an external resistive divider for adjustable output. No connect. Enable pin. A logic high enables normal operation. A logic low shuts down the converter. Switching node. Connect the inductor to this pin. It is connected internally to the drain of both high- and low-side MOSFETs. Input power return pin; connected to the source of the N-channel MOSFET. Connect to the output and input capacitor return. Exposed paddle (bottom): connect to ground directly beneath the package. Pin Configuration STDFN22-8 (Top View) VP VIN GND FB 2 1 8 2 7 3 6 4 5 PGND LX EN N/C 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Absolute Maximum Ratings1 Symbol VIN VLX VOUT VEN TJ TLEAD Description Input Voltage and Bias Power to GND LX to GND FB to GND EN to GND Operating Junction Temperature Range Maximum Soldering Temperature (at leads, 10 sec) Value Units 6.0 -0.3 to VIN + 0.3 -0.3 to VIN + 0.3 -0.3 to 6.0 -40 to 150 300 V V V V C C Value Units 2 50 W C/W Thermal Information Symbol PD JA Description Maximum Power Dissipation (STDFN22-8) Thermal Resistance2 (STDFN22-8) 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum Rating should be applied at any one time. 2. Mounted on an FR4 board. 2120.2007.10.1.1 3 AAT2120 500mA Low Noise Step-Down Converter Electrical Characteristics1 VIN = 3.6V, TA = -40C to +85C, unless otherwise noted; typical values are TA = 25C. Symbol Description VIN Input Voltage VUVLO UVLO Threshold VOUT Output Voltage Tolerance2 VOUT IQ ISHDN ILIM Output Voltage Range Quiescent Current Shutdown Current P-Channel Current Limit High-Side Switch On Resistance Low-Side Switch On Resistance Line Regulation Feedback Threshold Voltage Accuracy FB Leakage Current Oscillator Frequency RDS(ON)H RDS(ON)L VLinereg/VIN VFB IFB FOSC TS TSD THYS VEN(L) VEN(H) IEN Startup Time Over-Temperature Shutdown Threshold Over-Temperature Shutdown Hysteresis Enable Threshold Low Enable Threshold High Input Low Current Conditions Min Typ Max Units 5.5 2.3 V V mV V 3.0 % VIN 85 1.0 1.8 V A A mA %/V V A MHz 100 s 105 15 C C V V A 2.7 VIN Rising Hysteresis VIN Falling IOUT = 0 to 500mA, VIN = 2.7V to 5.5V 70 1.4 -3.0 0.6 No Load EN = GND VIN = 2.7V to 5.5V VIN = 3.6V VOUT = 1.0V 45 0.591 From Enable to Output Regulation 700 0.59 0.42 0.2 0.600 0.609 0.2 0.6 VIN = VEN = 5.5V 1.4 -1.0 1.0 1. The AAT2120 is guaranteed to meet performance specifications over the -40C to +85C operating temperature range and is assured by design, characterization, and correlation with statistical process controls. 2. Output voltage tolerance is independent of feedback resistor network accuracy. 4 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Typical Characteristics Efficiency vs. Load Load Regulation (VOUT = 3.0V; L = 4.7H) (VOUT = 3.0V; L = 4.7H) 1.0 100 Load Regulation (%) Efficiency (%) 90 VIN = 3.6V 80 VIN = 4.2V 70 VIN = 5.0V 60 50 40 0.1 1 10 100 0.8 0.6 VIN = 3.6V 0.4 0.0 -0.2 -0.4 VIN = 4.2V -0.6 -0.8 -1.0 1000 0.1 1 Output Current (mA) Load Regulation (VOUT = 1.8V; L = 3.3H) (VOUT = 1.8V; L = 3.3H) Efficiency (%) 80 VIN = 4.2V 70 60 50 0.8 0.6 10 100 1000 VIN = 4.2V 0.4 0.2 0.0 -0.2 -0.4 VIN = 3.6V -0.6 0.1 1 Output Current (mA) 10 100 1000 Output Current (mA) Efficiency vs. Load Load Regulation (VOUT = 1.2V; L = 1.5H) (VOUT = 1.2V; L = 1.5H) 100 1.0 VIN = 2.7V VIN = 3.6V 70 VIN = 4.2V 60 VIN = 5.0V 50 40 0.1 0.6 VIN = 3.6V 0.4 0.2 0.0 -0.2 -0.4 VIN = 4.2V -0.6 VIN = 5.0V -0.8 -1.0 1 10 Output Current (mA) 2120.2007.10.1.1 VIN = 2.7V 0.8 Load Regulation (%) 90 Efficiency (%) VIN = 2.7V -0.8 -1.0 40 1 1000 1.0 VIN = 3.6V 90 80 100 Efficiency vs. Load VIN = 2.7V 0.1 10 Output Current (mA) Load Regulation (%) 100 VIN = 5.0V 0.2 100 1000 0.1 1 10 100 Output Current (mA) 5 AAT2120 500mA Low Noise Step-Down Converter Typical Characteristics Line Regulation Soft Start (VOUT = 1.8V) (VIN = 3.6V; VOUT = 1.8V; 500mA) 1.4 VO VEN 1.2 2 1.0 1 0.8 0 0.6 -1 0.4 ILX -2 0.2 -3 0.0 -4 -0.2 0.20 Accuracy (%) Enable and Output Voltage (top) (V) 3 Inductor Current (bottom) (A) 4 0.30 IOUT = 10mA 0.10 IOUT = 500mA IOUT = 0mA 0.00 IOUT = 50mA IOUT = 150mA -0.10 -0.20 IOUT = 250mA -0.30 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 Input Voltage (V) Time (100s/div) Frequency Variation vs. Input Voltage Output Voltage Error vs. Temperature (VIN = 3.6V; VOUT = 1.8V; IOUT = 500mA) 4 Frequency Variation (%) Output Error (%) 3.0 2.0 1.0 0.0 -1.0 -2.0 -40 -20 0 20 40 60 80 2 1 0 -1 100 VOUT = 3.0V -2 -3 -4 2.7 -3.0 VOUT = 1.8V 3 3.1 3.5 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) Temperature (C) No Load Quiescent Current vs. Input Voltage Switching Frequency Variation vs. Temperature (VIN = 3.6V; VOUT = 1.8V) 60 8 55 Supply Current (A) 10 Variation (%) 6 4 2 0 -2 -4 -6 -8 -10 85C 45 25C 40 35 -40C 30 25 20 -40 -20 0 20 40 Temperature (C) 6 50 60 80 100 2.7 3.1 3.5 3.9 4.3 4.7 5.1 5.5 Input Voltage (V) 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Typical Characteristics P-Channel RDS(ON) vs. Input Voltage 1000 750 120C 700 100C 700 600 500 300 2.5 600 550 450 3.5 4.0 4.5 5.0 5.5 6.0 300 2.5 25C 3.0 3.5 4.0 4.5 5.0 5.5 Load Transient Response (350mA to 500mA; VIN = 3.6V; VOUT = 1.8V; COUT = 4.7F; CFF = 100pF) VO 1.6 1.4 IO 1.2 1.0 0.8 I LX 0.6 Time (20s/div) 2.0 1.9 1.8 1.7 1.6 VO IO 1.5 1.4 1.3 1.2 1.1 I LX 1.0 Load and Inductor Current (bottom) (100mA/div) 1.8 Output Voltage (top) (V) Load Transient Response (1mA to 500mA; VIN = 3.6V; VOUT = 1.8V; COUT = 4.7F; CFF = 100pF) 2.0 6.0 Input Voltage (V) Load and Inductor Current (bottom) (400mA/div) Output Voltage (top) (V) Input Voltage (V) 2.2 100C 500 350 3.0 120C 400 25C 400 85C 650 85C 800 RDS(ON) (m ) 900 RDS(ON) (m ) N-Channel RDS(ON) vs. Input Voltage Time (25s/div) Line Response (VOUT = 1.8V @ 500mA) Output Voltage (top) (V) 7.0 1.85 VO 1.80 1.75 6.0 5.5 1.70 1.65 6.5 5.0 4.5 VIN 1.60 4.0 1.55 3.5 1.50 3.0 Input Voltage (bottom) (V) 1.90 Time (25s/div) 2120.2007.10.1.1 7 AAT2120 500mA Low Noise Step-Down Converter Output Ripple (VIN = 3.6V; VOUT = 1.8V; IOUT = 500mA) 40 0.14 20 0.12 0.10 -20 0.08 -40 0.06 -60 0.04 -80 ILX 0.02 0.00 -100 -0.02 -120 Time (2s/div) 8 1.0 40 20 0.9 VO 0.8 0 0.7 -20 -40 ILX 0.6 -60 0.5 -80 0.4 -100 0.3 -120 0.2 Inductor Current (bottom) (A) 0 VO Output Voltage (AC Coupled) (top) (mV) Output Ripple (VIN = 3.6V; VOUT = 1.8V; IOUT = 1mA) Inductor Current (bottom) (A) Output Voltage (AC Coupled) (top) (mV) Typical Characteristics Time (200ns/div) 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Functional Block Diagram FB VP VIN Err Amp DH Voltage Reference LX Logic EN INPUT DL PGND GND Functional Description The AAT2120 is a high performance 500mA, 1.8MHz monolithic step-down converter designed to operate with an input voltage range of 2.7V to 5.5V. The converter operates at 1.8MHz, which minimizes the size of external components. Typical values are 3.3H for the output inductor and 4.7F for the ceramic output capacitor. The device is designed to operate with an output voltage as low as 0.6V. Power devices are sized for 500mA current capability while maintaining over 2120.2007.10.1.1 90% efficiency at full load. Low current efficiency is maintained at greater than 80% down to 1mA of load current. At dropout, the converter duty cycle increases to 100% and the output voltage tracks the input voltage minus the RDS(ON) drop of the P-channel highside MOSFET. A high-DC gain error amplifier with internal compensation controls the output. It provides excellent transient response and load/line regulation. Soft start eliminates any output voltage overshoot when the enable or the input voltage is applied. 9 AAT2120 500mA Low Noise Step-Down Converter Control Loop The AAT2120 is a 500mA current mode step-down converter. The current through the P-channel MOSFET (high side) is sensed for current loop control, as well as short-circuit and overload protection. A fixed slope compensation signal is added to the sensed current to maintain stability for duty cycles greater than 50%. The peak current mode loop appears as a voltage-programmed current source in parallel with the output capacitor. The output of the voltage error amplifier programs the current mode loop for the necessary peak switch current to force a constant output voltage for all load and line conditions. Internal loop compensation terminates the transconductance voltage error amplifier output. The error amplifier reference is fixed at 0.6V. Soft Start / Enable Soft start increases the inductor current limit point in discrete steps when the input voltage or enable input is applied. It limits the current surge seen at the input and eliminates output voltage overshoot. When pulled low, the enable input forces the AAT2120 into a low-power, non-switching state. The total input current during shutdown is less than 1A. Current Limit and Over-Temperature Protection For overload conditions, the peak input current is limited. As load impedance decreases and the output voltage falls closer to zero, more power is dissipated internally, raising the device temperature. Thermal protection completely disables switching when internal dissipation becomes excessive, protecting the device from damage. The junction over-temperature threshold is 105C with 15C of hysteresis. Under-Voltage Lockout Internal bias of all circuits is controlled via the VIN power. Under-voltage lockout (UVLO) guarantees sufficient VIN bias and proper operation of all internal circuits prior to activation. 10 Applications Information Inductor Selection The step-down converter uses peak current mode control with slope compensation to maintain stability for duty cycles greater than 50%. The output inductor value must be selected so the inductor current down slope meets the internal slope compensation requirements. The internal slope compensation for the adjustable and low-voltage fixed versions of the AAT2120 is 0.45A/sec. This equates to a slope compensation that is 75% of the inductor current down slope for a 1.8V output and 3.0H inductor. m= 0.75 VO 0.75 1.8V A = = 0.45 L 3.0H sec This is the internal slope compensation for the AAT2120. When externally programming to 3.0V, the calculated inductance is 5.0H. L= 0.75 VO = m = 1.67 sec 0.75 VO 1.67 A VO A 0.45A sec sec 3.0V = 5.0H A In this case, a standard 4.7H value is selected. For most designs, the AAT2120 operates with an inductor value of 1H to 4.7H. Table 1 displays inductor values for the AAT2120 with different output voltage options. Manufacturer's specifications list both the inductor DC current rating, which is a thermal limitation, and the peak current rating, which is determined by the saturation characteristics. The inductor should not show any appreciable saturation under normal load conditions. Some inductors may meet the peak and average current ratings yet result in excessive losses due to a high DCR. Always consider the losses associated with the DCR and its effect on the total converter efficiency when selecting an inductor. 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Output Voltage (V) L1 (H) 1.0 1.2 1.5 1.8 2.5 3.0 3.3 1.5 2.2 2.7 3.0 3.9 4.7 5.6 The input capacitor RMS ripple current varies with the input and output voltage and will always be less than or equal to half of the total DC load current. VO V * 1- O = VIN VIN D * (1 - D) = Input Capacitor Select a 4.7F to 10F X7R or X5R ceramic capacitor for the input. To estimate the required input capacitor size, determine the acceptable input ripple level (VPP) and solve for CIN. The calculated value varies with input voltage and is a maximum when VIN is double the output voltage. CIN = V VO * 1- O VIN VIN VPP - ESR * FS IO VO V 1 * 1 - O = for VIN = 2 * VO VIN VIN 4 CIN(MIN) = 1 VPP - ESR * 4 * FS IO Always examine the ceramic capacitor DC voltage coefficient characteristics when selecting the proper value. For example, the capacitance of a 10F, 6.3V, X5R ceramic capacitor with 5.0V DC applied is actually about 6F. The maximum input capacitor RMS current is: IRMS = IO * 2120.2007.10.1.1 VO V * 1- O VIN VIN 1 2 for VIN = 2 * VO Table 1: Inductor Values. The 3.0H CDRH2D09 series inductor selected from Sumida has a 150m DCR and a 470mA DC current rating. At full load, the inductor DC loss is 9.375mW which gives a 2.08% loss in efficiency for a 250mA, 1.8V output. 0.52 = IRMS(MAX) = VO IO 2 V * 1- O The term VIN VIN appears in both the input voltage ripple and input capacitor RMS current equations and is a maximum when VO is twice VIN. This is why the input voltage ripple and the input capacitor RMS current ripple are a maximum at 50% duty cycle. The input capacitor provides a low impedance loop for the edges of pulsed current drawn by the AAT2120. Low ESR/ESL X7R and X5R ceramic capacitors are ideal for this function. To minimize stray inductance, the capacitor should be placed as closely as possible to the IC. This keeps the high frequency content of the input current localized, minimizing EMI and input voltage ripple. The proper placement of the input capacitor (C1) can be seen in the evaluation board layout in Figure 2. A laboratory test set-up typically consists of two long wires running from the bench power supply to the evaluation board input voltage pins. The inductance of these wires, along with the low-ESR ceramic input capacitor, can create a high Q network that may affect converter performance. This problem often becomes apparent in the form of excessive ringing in the output voltage during load transients. Errors in the loop phase and gain measurements can also result. Since the inductance of a short PCB trace feeding the input voltage is significantly lower than the power leads from the bench power supply, most applications do not exhibit this problem. 11 AAT2120 500mA Low Noise Step-Down Converter In applications where the input power source lead inductance cannot be reduced to a level that does not affect the converter performance, a high ESR tantalum or aluminum electrolytic should be placed in parallel with the low ESR, ESL bypass ceramic. This dampens the high Q network and stabilizes the system. Output Capacitor The output capacitor limits the output ripple and provides holdup during large load transitions. A 4.7F to 10F X5R or X7R ceramic capacitor typically provides sufficient bulk capacitance to stabilize the output during large load transitions and has the ESR and ESL characteristics necessary for low output ripple. For enhanced transient response and low temperature operation application, a 10F (X5R, X7R) ceramic capacitor is recommended to stabilize extreme pulsed load conditions. The output voltage droop due to a load transient is dominated by the capacitance of the ceramic output capacitor. During a step increase in load current, the ceramic output capacitor alone supplies the load current until the loop responds. Within two or three switching cycles, the loop responds and the inductor current increases to match the load current demand. The relationship of the output voltage droop during the three switching cycles to the output capacitance can be estimated by: COUT = 3 * ILOAD VDROOP * FS Once the average inductor current increases to the DC load level, the output voltage recovers. The above equation establishes a limit on the minimum value for the output capacitor with respect to load transients. The internal voltage loop compensation also limits the minimum output capacitor value to 4.7F. This is due to its effect on the loop crossover frequency (bandwidth), phase margin, and gain margin. Increased output capacitance will reduce the crossover frequency with greater phase margin. The maximum output capacitor RMS ripple current is given by: IRMS(MAX) = 1 VOUT * (VIN(MAX) - VOUT) L * FS * VIN(MAX) 2* 3 * Dissipation due to the RMS current in the ceramic output capacitor ESR is typically minimal, resulting in less than a few degrees rise in hot-spot temperature. Adjustable Output Resistor Selection Resistors R1 and R2 of Figure 1 program the output to regulate at a voltage higher than 0.6V. To limit the bias current required for the external feedback resistor string while maintaining good noise immunity, the suggested value for R2 is 59k. Decreased resistor values are necessary to maintain noise immunity on the FB pin, resulting in increased quiescent current. Table 2 summarizes the resistor values for various output voltages. VOUT 3.3V R1 = V -1 * R2 = 0.6V - 1 * 59k = 267k REF With enhanced transient response for extreme pulsed load application, an external feed-forward capacitor, (C3 in Figure 1), can be added. R2 = 59k R2 = 221k VOUT (V) R1 (k) R1 (k) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 3.3 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 267 75 113 150 187 221 261 301 332 442 464 523 715 1000 Table 2: Adjustable Resistor Values For Step-Down Converter. 12 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter For the condition where the step-down converter is in dropout at 100% duty cycle, the total device dissipation reduces to: Thermal Calculations There are three types of losses associated with the AAT2120 step-down converter: switching losses, conduction losses, and quiescent current losses. Conduction losses are associated with the RDS(ON) characteristics of the power output switching devices. Switching losses are dominated by the gate charge of the power output switching devices. At full load, assuming continuous conduction mode (CCM), a simplified form of the losses is given by: PTOTAL = 2 O I PTOTAL = IO2 * RDS(ON)H + IQ * VIN Since RDS(ON), quiescent current, and switching losses all vary with input voltage, the total losses should be investigated over the complete input voltage range. Given the total losses, the maximum junction temperature can be derived from the JA for the STDFN22-8 package which is 50C/W. * (RDS(ON)H * VO + RDS(ON)L * [VIN - VO]) VIN TJ(MAX) = PTOTAL * JA + TAMB + (tsw * FS * IO + IQ) * VIN IQ is the step-down converter quiescent current. The term tsw is used to estimate the full load stepdown converter switching losses. U1 1 VIN 2 3 4 C1 4.7F VP PGND VIN LX GND EN FB N/C 8 7 LX L1 +VOUT 6 5 AAT2120 C2 4.7F R1 Adj. C3 (optional) 100pF R2 59k GND GND Figure 1: AAT2120 Schematic. 2120.2007.10.1.1 13 AAT2120 500mA Low Noise Step-Down Converter Layout The suggested PCB layout for the AAT2120 in an STDFN22-8 package is shown in Figures 2, 3, and 4. The following guidelines should be used to help ensure a proper layout. 1. The input capacitor (C1) should connect as closely as possible to VP (Pin 1), PGND (Pin 8), and GND (Pin 3) 2. C2 and L1 should be connected as closely as possible. The connection of L1 to the LX pin (Pin 7) should be as short as possible. Do not make the node small by using narrow trace. The trace should be kept wide, direct and short. 3. The feedback pin (Pin 4) should be separate from any power trace and connect as closely as possible to the load point. Sensing along a Figure 2: AAT2120 Evaluation Board Top Side Layout. high-current load trace will degrade DC load regulation. Feedback resistors should be placed as closely as possible to the FB pin (Pin 4) to minimize the length of the high impedance feedback trace. If possible, they should also be placed away from the LX (switching node) and inductor to improve noise immunity. 4. The resistance of the trace from the load return to PGND (Pin 8) and GND (Pin 3) should be kept to a minimum. This will help to minimize any error in DC regulation due to differences in the potential of the internal signal ground and the power ground. 5. A high density, small footprint layout can be achieved using an inexpensive, miniature, nonshielded, high DCR inductor. Figure 3: Exploded View of AAT2120 Evaluation Board Top Side Layout. Figure 4: AAT2120 Evaluation Board Bottom Side Layout. 14 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Step-Down Converter Design Example Specifications VO = 1.8V @ 250mA, Pulsed Load ILOAD = 200mA VIN = 2.7V to 4.2V (3.6V nominal) FS = 1.8MHz TAMB = 85C 1.8V Output Inductor L1 = 1.67 sec sec VO2 = 1.67 1.8V = 3H A A (use 3.0H; see Table 1) For Sumida inductor CDRH2D09-3R0, 3.0H, DCR = 150m. IL1 = VO V 1.8V 1.8V 1- O = 1= 190mA L1 FS VIN 3.0H 1.8MHz 4.2V IPKL1 = IO + IL1 = 250mA + 95mA = 345mA 2 PL1 = IO2 DCR = 250mA2 150m = 9.375mW 1.8V Output Capacitor VDROOP = 0.1V COUT = 3 * ILOAD 3 * 0.2A = = 3.3F (use 3.3F) 0.1V * 1.8MHz VDROOP * FS IRMS = (VO) * (VIN(MAX) - VO) 1 1.8V * (4.2V - 1.8V) * = 66mArms = 3.0H * 1.8MHz * 4.2V * V L1 * F 2* 3 2* 3 S IN(MAX) 1 * Pesr = esr * IRMS2 = 5m * (66mA)2 = 21.8W 2120.2007.10.1.1 15 AAT2120 500mA Low Noise Step-Down Converter Input Capacitor Input Ripple VPP = 25mV CIN = IRMS = VPP IO 1 1 = = 1.16F (use 4.7F) 25mV - 5m * 4 * 1.8MHz - ESR * 4 * FS 0.2A IO = 0.1Arms 2 P = esr * IRMS2 = 5m * (0.1A)2 = 0.05mW AAT2120 Losses PTOTAL = IO2 * (RDS(ON)H * VO + RDS(ON)L * [VIN -VO]) VIN + (tsw * FS * IO + IQ) * VIN = 0.22 * (0.59 * 1.8V + 0.42 * [4.2V - 1.8V]) 4.2V + (5ns * 1.8MHz * 0.2A + 45A) * 4.2V = 19.71mW TJ(MAX) = TAMB + JA * PLOSS = 85C + (50C/W) * 26.14mW = 86C 16 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Output Voltage VOUT (V) R2 = 59k R1 (k) R2 = 221k1 R1 (k) L1 (H) 0.62 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.8 1.85 2.0 2.5 3.3 -- 19.6 29.4 39.2 49.9 59.0 68.1 78.7 88.7 118 124 137 187 267 -- 75 113 150 187 221 261 301 332 442 464 523 715 1000 1.5 1.5 1.5 1.5 1.5 1.5 1.5 2.2 2.7 3.0/3.3 3.0/3.3 3.0/3.3 3.9/4.2 5.6 Table 3: Evaluation Board Component Values. Manufacturer Sumida Sumida Sumida Sumida Sumida Sumida Sumida Sumida Sumida Sumida Sumida Taiyo Yuden Taiyo Yuden Taiyo Yuden Taiyo Yuden FDK FDK FDK FDK Part Number Inductance (H) Max DC Current (mA) DCR (m) Size (mm) LxWxH Type CDRH2D14-1R5 CDRH2D14-2R2 CDRH2D14-2R7 CDRH2D14-3R3 CDRH2D14-3R9 CDRH2D14-4R7 CDRH2D14-5R6 CDRH2D11-1R5 CDRH2D11-2R2 CDRH2D11-3R3 CDRH2D11-4R7 NR3010 NR3010 NR3010 NR3010 MIPWT3226D-1R5 MIPWT3226D-2R2 MIPWT3226D-3R0 MIPWT3226D-4R2 1.5 2.2 2.7 3.3 3.9 4.7 5.6 1.5 2.2 3.3 4.7 1.5 2.2 3.3 4.7 1.5 2.2 3 4.2 1800 1500 1350 1200 1100 1000 950 900 780 600 500 1200 1100 870 750 1200 1100 1000 900 50 75 85 100 110 135 150 54 78 98 135 80 95 140 190 90 100 120 140 3.0x3.0x1.55 3.0x3.0x1.55 3.0x3.0x1.55 3.0x3.0x1.55 3.0x3.0x1.55 3.0x3.0x1.55 3.0x3.0x1.55 3.2x3.2x1.2 3.2x3.2x1.2 3.2x3.2x1.2 3.2x3.2x1.2 3.0x3.0x1.0 3.0x3.0x1.0 3.0x3.0x1.0 3.0x3.0x1.0 3.2x2.6x0.8 3.2x2.6x0.8 3.2x2.6x0.8 3.2x2.6x0.8 Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Shielded Chip shielded Chip shielded Chip shielded Chip shielded Table 4: Suggested Inductors and Suppliers. 1. For reduced quiescent current, R2 = 221k. 2. R2 is opened, R1 is shorted. 2120.2007.10.1.1 17 AAT2120 500mA Low Noise Step-Down Converter Manufacturer Murata Murata Part Number Value (F) Voltage Rating Temp. Co. Case Size GRM118R60J475KE19B GRM188R60J106ME47D 4.7 10 6.3 6.3 X5R X5R 0603 0603 Table 5: Surface Mount Capacitors. 18 2120.2007.10.1.1 AAT2120 500mA Low Noise Step-Down Converter Ordering Information Output Voltage Package Marking1 Part Number (Tape and Reel)2 0.6V STDFN22-8 YDXYY AAT2120IES-0.6-T1 All AnalogicTech products are offered in Pb-free packaging. The term "Pb-free" means semiconductor products that are in compliance with current RoHS standards, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. For more information, please visit our website at http://www.analogictech.com/pbfree. 1. XYY = assembly and date code. 2. Sample stock is generally held on all part numbers listed in BOLD. 2120.2007.10.1.1 19 AAT2120 500mA Low Noise Step-Down Converter Package Information1 STDFN22-8 Index Area (D/2 x E/2) 0.80 0.05 Detail "A" 1.45 0.05 2.00 0.05 2.00 0.05 Top View Bottom View Side View Pin 1 Indicator (optional) 0.45 0.05 0.23 0.05 0.05 0.05 0.15 0.025 0.55 0.05 0.35 0.05 Detail "A" All dimensions in millimeters. 1. The leadless package family, which includes QFN, TQFN, DFN, TDFN and STDFN, has exposed copper (unplated) at the end of the lead terminals due to the manufacturing process. A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. (c) Advanced Analogic Technologies, Inc. AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service without notice. Except as provided in AnalogicTech's terms and conditions of sale, AnalogicTech assumes no liability whatsoever, and AnalogicTech disclaims any express or implied warranty relating to the sale and/or use of AnalogicTech products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. Testing and other quality control techniques are utilized to the extent AnalogicTech deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed. AnalogicTech and the AnalogicTech logo are trademarks of Advanced Analogic Technologies Incorporated. All other brand and product names appearing in this document are registered trademarks or trademarks of their respective holders. Advanced Analogic Technologies, Inc. 3230 Scott Boulevard, Santa Clara, CA 95054 Phone (408) 737- 4600 Fax (408) 737- 4611 20 2120.2007.10.1.1