Temperature Compensated Crystal Oscillator (TCXO) X1G0038410007xx Data sheet MODEL TG-5006CJ-47L 32.000000 MHz X1G0041310042xx Product. No. Please refer to the 10.Packing information about xx (last 2 digits) SEIKO EPSON CORPORATION Pb free. Complies with EU RoHS directive. *About the products without the Pb-free mark. Contains Pb in products exempted by EU RoHS directive. (Contains Pb in sealing glass, high melting temperature type solder or other.) INTRODUCTION 1. Any part of this material may not be reproduced or duplicated in any form or any means without the written permission of Seiko Epson. 2. This sheet is not intended to guarantee or provide an approval of implementation of industrial patents. [ 1 ] Characteristics * Package size (2.0 mmx1.6 mmx0.73 mm) * High stability TCXO * Output waveform : Clipped sine wave * Reference weight Typ.9.1mg [ 2 ] Absolute maximum ratings Parameter Supply voltage Storage temperature range Symbol Vcc-GND T_stg Min. -0.3 -40 Specifications Typ. - Max. +4.0 +90 Unit Conditions V C Storage as single product [ 3 ] Recommended operating conditions Specifications Unit Conditions Min. Typ. Max. Vcc 2.85 3 3.15 V Supply voltage GND 0 0 V Operating temperature range T_use -30 +85 C 0 Load_R 9 10 11 k Output load DC cut capacitor=0.01F Load_C 9 10 11 pF DC-cut capacitor * Cc 0.01 F * DC-cut capacitor is not included in this TCXO. Please attach an external DC-cut capacitor to the out pin. Parameter Symbol (Vcc=3 V, GND=0.0 V, Load=10 k // 10 pF, T_use=+25C) [ 4 ] Frequency characteristics fo Min. - Specifications Typ. 32 Max. - MHz Frequency tolerance f_tol -0.8 - +0.8 x10 Frequency tolerance *1 f_tol -2.0 - +2.0 x10 fo-Tc -2.0 - +2.0 x10 T_use = -30 C to +85 C x10 x10 x10 x10 10 k // 10 pF +/- 10% Parameter Output Frequency Frequency / temperature characteristics Frequency / load coefficient Frequency / voltage coefficient Symbol fo-Load fo-Vcc -0.2 +0.2 -0.2 +0.2 -1.0 +1.0 Frequency aging f_age *1 Include initial frequency tolerance and frequency deviation after reflow cycles. *2 Measured in the elapse of 24 hours after reflow soldering. *3 Vcc +/- 5% must be in operating supply voltage range (2.85 V to 3.15 V) 2 Unit Conditions T_use=+25C+/-2C Before reflow T_use=+25C+/-2C After 2 reflows *2 Vcc +/- 5 % 1st year, T_use=25degC - (Vcc=3 V, GND=0.0 V, Load=10 k // 10 pF, T_use=+25C) [ 5 ] Electrical characteristics Parameter Symbol Current consumption Output level Symmetry Icc Vp-p SYM Start up time t_sta Harmonics Phase noise - L(f) Min. 0.8 40 Specifications Typ. - Max. 2.0 1.5 60 - - - 3 Unit Conditions mA V % T_Use = +25C , 10 k//10pF 2.0 ms Within 90% of final amp. - 2.0 ms F = +/- 1.0 x 10-6 - -8.0 -82 -108 -130 -145 -148 -148 dBc - Peak to peak 10 k//10pF +/- 10% GND Level 10Hz offset 100Hz offset dBc/Hz 1kHz offset 10kHz offset 100kHz offset 1MHz offset [ 6 ] Test circuit 1) Output Load : Load_R // Load_C = 10 k // 10 pF DC-cut Capacitor Supply Voltage Vcc OUT N.C. GND By-pass Capacitor Load_C Test Point Load_R 0.01 to 0.1 F 2) Current consumption DC-cut Capacitor A Supply Voltage Vcc OUT N.C. GND By-pass Capacitor Load_C Load_R 0.01 to 0.1 F 3) Conditions 1. Oscilloscope: Impedance Min. 1M Input capacitance Max. 10 pF Band width Min. 300 MHz Impossible to measure both frequency and wave form at the same time. (In case of using oscilloscope's amplifier output, possible to measure both at the same time.) 2. Load_C includes probe capacitance. 3. A capacitor (By-pass:0.01 to 0.1 F) is placed between Vcc and GND,and closely to TCXO. 4. Use the current meter whose internal impedance value is small. 5. Power Supply Impedance of power supply should be as low as possible. 6. GND pin should be connected to low impedance GND. 4 [ 7 ] Outline drawingunit:mm [ 8 ] Recommended foot printunit:mm 0.6 #3 #4 #1 1.13 #2 2.00.15 #3 0.75 1.60.15 #4 #2 #1 1.580.1 Pin # 1 2 3 4 #2 0.400.1 #1 1.180.1 C0.15 0.730.07 (0.27) 1.65 #4 Do not connect "N.C." pin with any other leads (also mutually) To maintain stable operation, provide a 0.01 to 0.1 F by-pass capacitor at a location as near as possible to the power source terminal of the crystal product (between Vcc - GND). #3 1.20.1 Connection N.C. GND OUT Vcc Material Ceramics(Cavity) Au plated nickel(Electric terminal) Fe-Ni-Co(Lid) [ 9 ] Reflow profile Temperature [ C ] 300 TP ; +260 C +255 C 250 200 150 TL ; +217 C Ts max ; +200 C Ts min ; +150 C tp ; 20 s Avg. Ramp-up 3 C / s Max. tL 60 s to 150 s ( +217 C over ) to 40 s Ramp-down 6 C / s Max. ts 60 s to 180 s ( +150 C to +200 C ) 100 50 Time +25 C to Peak 0 60 120 180 240 300 360 420 480 540 600 660 720 780 Time [ s ] 5 [ 10 ] Packing information 1) Product number last 2 digits code(xx) description. The recommended code is "00" X1G0041310042xx Condition Code 12000pcs / Reel 00 Any Q'ty vinyl bag(Tape cut) 01 Any Q'ty / Reel 11 1000pcs / Reel 14 2000pcs / Reel 15 3000pcs / Reel 16 2) Taping specification Subject to EIA-481 & IEC-60286 (1) Tape dimensions TE0804L Material of the Carrier Tape : PS Material of the Top Tape : PET+PE unit:mm 1 .0 +0 .1 0 1 .850 .1 (2) Reel dimensions Center material : PS Material of the Reel : PS 13.41. 0 2.0 0 . 5 6 330.0 2 . 0 13.00. 2 9.41.0 100.0 4 .00 .1 2 .250 .1 3 .50 .1 0 .250 .05 8 .00 .2 +0 .1 1 .5 0 2 .00 .1 1 .00 .1 1 .750 .1 4 .0 0 .1 [ 11 ] Handling precautions Prior to using this product, please carefully read the section entitled "Precautions" on our Web site ( http://www5.epsondevice.com/en/quartz/tech/precaution/ ) for instructions on how to handle and use the product properly to ensure optimal performance of the product in your equipment. Before using the product under any conditions other than those specified therein, please consult with us to verify and confirm that the performance of the product will not be negatively affected by use under such conditions. In addition to the foregoing precautions, in order to avoid the deteriorating performance of the product, we strongly recommend that you DO NOT use the product under ANY of the following conditions: (1) Mounting the product on a board using water-soluble solder flux and using the product without removing the residue of the flux completely from the board. The residue of such flux that is soluble in water or water-soluble cleaning agent, especially the residues which contains active halogens, will negatively affect the performance and reliability of the product. (2) Using the product in any manner that will result in any shock or impact to the product. (3) Using the product in places where the product is exposed to water, chemicals, organic solvent, sunlight, dust, corrosive gasses, or other materials. (4) Using the product in places where the product is exposed to static electricity or electromagnetic waves. (5) Applying ultrasonic cleaning without advance verification and confirmation that the product will not be affected by such a cleaning process, because it may damage the crystal, IC and/or metal line of the product. (6) Touching the IC surface with tweezers or other hard materials directly. (7) Using the product under any other conditions that may negatively affect the performance and/or reliability of the product. (8) Power supply with ripple may cause of incorrect operation or degradation of phase noise characteristics, so please evaluate before use. (9) Frequency aging is from environmental tests results to the expectation of the amount of the frequency variation. This doesn't guarantee the product-life cycle. (10)This components used underfill material at the back side of package. After mounting this components on the board, there's possibility of IC damage happened by thermal expansion of adhesive, if adhesive will break into between TCXO and the board. Please do not use adhesive, this will cause oscillation stop in case of IC damaged by adhesive. Should any customer use the product in any manner contrary to the precautions and/or advice herein, such use shall be done at the customer's own risk. 7 [Notice] * This material is subject to change without notice. * Any part of this material may not be reproduced or duplicated in any form or any means without the written permission of SeJQo Epson. * The information about applied data,circuitry, software, usage, etc. written in this material is intended for reference only. SeJQo Epson does not assume any liability for the occurrence of customer damage or infringing on any patent or copyright of a third party. This material does not authorize the licensing for any patent or intellectual copyrights. * When exporting the products or technology described in this material, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. * You are requested not to use the products (and any technical information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you would the who maynot usemake the products for such prohibited purposes. * These products are intended for general use in electronic equipment. When using them in specific applications that require extremely high reliability, such as the applications stated below, you must obtain permission from SeJQo Epson in advance. / Space equipment (artificial satellites, rockets, etc.) / Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.) / Medical instruments to sustain life / Submarine transmitters / Power stations and related / Fire work equipment and security equipment / Traffic control equipment / And others requiring equivalent reliability. * All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective. [Contact us] http://www5.epsondevice.com/en/contact/ 8