Clock OSC SG-310SCF SG-310SCF 48.000000 MHz M Product name Product Number / Ordering code Q33310F700165xx Please refer to the 8.Packing information about xx (last 2 digits) Output waveform CMOS Pb free / Complies with EU RoHS directive Reference weight Typ. 26 mg 1.Absolute maximum ratings Parameter Symbol Min. Typ. Max. Unit Vcc-GND T_stg Vin -0.3 -40 -0.3 - 4.2 125 Vcc+0.3 V C V 2.Specifications(characteristics) Parameter Symbol Min. Typ. Max. Unit f0 Vcc T_use f_tol Icc I_std SYM VOH VOL L_CMOS VIH VIL tr tf t_str tDJ TRJ tRMS tp-p 2.7 -40 -100 45 0.9Vcc 0.8Vcc - 48.0000 3.3 TBD TBD TBD TBD 3.6 85 100 4.5 2.0 55 0.1Vcc 15 0.2Vcc 4 4 10 - tacc - TBD - ps tPJ L(f) -5 - TBD TBD TBD TBD TBD TBD TBD TBD - 5 - ps dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz Maximum supply voltage Storage temperature Input voltage Output frequency Supply voltage Operating temperature Frequency tolerance Current consumption Stand-by current Symmetry Output voltage Output load condition Input voltage Rise time Fall time Start-up time Jitter Phase jitter Phase noise Frequency aging f_age 1 Page MHz V C x10-6 mA A % Conditions / Remarks Storage as single product ST terminal Conditions / Remarks T_use No load condition ST = GND 50% Vcc Level L_CMOS=<15pF IOH=-3mA IOL=3mA pF CMOS Load ST terminal ST terminal ns ns ms ps ps ps ps x10-6 0.2Vcc to 0.8Vcc Level, L_CMOS=15pF 0.2Vcc to 0.8Vcc Level, L_CMOS=15pF t = 0 at 0.9Vcc Deterministic Jitter Random Jitter (RMS of total distribution) Peak to Peak Accumulated Jitter() n=2 to 50000 cycles Off set Frequency: 12kHz to 20MHz Off set 1Hz Off set 10Hz Off set 100Hz Off set 1kHz Off set 10kHz Off set 100kHz Off set 1MHz @+25C first year - tr tf 3.Timing chart VCC 80 %VCC 50 %VCC 20 %VCC GND tw t 4.Test circuit swich 1) Waveform observation VCC ST by-pass capacitor supply Test Point GND OUT L_CMOS 2) Current consumption swich VCC ST A by-pass capacitor supply GND OUT Test Point *Current consumption under the disable function should be = GND. 3) Condition (1) Oscilloscope * Band width should be minimum 5 times higher (wider) than measurement frequency. * Probe earth should be placed closely from test point and lead length should be as short as possible * Recommendable to use miniature socket. (Don't use earth lead.) (2) L_CMOS also includes probe capacitance. (3) By-pass capacitor (0.01 mF to 0.1 mF) is placed closely between VCC and GND. (4) Use the current meter whose internal impedance value is small. (5) Power supply * Start up time (0 %VCC (R) 90 %VCC) of power source should be more than 150 ms. * Impedance of power supply should be as lowest as possible. 2 Page 5.External dimensions (Unit: mm) 3.2 0.2 C (ex.0.01 F) #3 1.4 #2 1.05 0.15 #2 #3 #1 #2 1.2 #1 0.9 Pin map Pin 1 2 3 4 #4 1.9 EF241A #4 0.7 0.9 E25.00B #1 (Unit: mm) 2.2 #3 2.5 0.2 #4 6.Footprint(Recommended) Connection ST GND OUT VCC 2.4 Note. ST pin = HIGH or "open" : Specified frequency output. ST pin = LOW : Output is high impedance, oscillation stops. To maintain stable operation, provide a 0.01uF to 0.1uF by-pass capacitor at a location as near as possible to the power source terminal of the crystal product (between Vcc 7.Reflow profile Reflow condition (Follow of JEDEC STD-020D.01) Temperature[C] 300 TP ;+260C +255C 250 ;+217C Tsmax;+200C TL 200 150 Tsmin;+150C tp;20sto40s Avg. Ramp-up 3C/sMax. tL 60sto150s (+217Cover) Ramp-down 6C/sMax. ts 60sto180s (+150Cto+200C) 100 50 Time +25CtoPeak 0 60 120 180 240 300 360 420 480 540 600 660 720 780 Time[s] 8.Packing information [ 1 ]Product number last 2 digits code(xx) description The recommended code is "00" Q33310F700165xx Code 01 11 12 Resist Condition Any Q'ty vinyl bag(Tape cut) Any Q'ty / Reel 250pcs / Reel Code 13 14 00 Condition 500pcs / Reel 1000pcs / Reel 2000pcs / Reel 3 Page [ 2 ] Taping specification Subject to EIA-481 & IEC-60286 (1) Tape dimensions Material of the Carrier Tape : PS Material of the Top Tape : PET+PE Unit: mm 3.50.1 2.80.1 (2) Reel dimensions Center material : PS Material of the Reel : PS Unit: mm 11.41.0 13.00.2 9.00.3 +0.3 2.0 -0 4 Page +0 4.00.1 180.0 -3.0 1.00.1 1.40.1 0.250.05 3.50.1 4.00.1 60.0 2.00.1 1.55 -0 8.00.2 +0.1 1.750.1 10 P: 400.1 9.Notice * This material is subject to change without notice. * Any part of this material may not be reproduced or duplicated in any form or any means without the written permission of Seiko Epson. * The information about applied data,circuitry, software, usage, etc. written in this material is intended for reference only. Seiko Epson does not assume any liability for the occurrence of customer damage or infringing on any patent or copyright of a third party. This material does not authorize the licensing for any patent or intellectual copyrights. * When exporting the products or technology described in this material, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. * You are requested not to use the products (and any technical information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other military purposes. You are also requested that you would not make the products available to any third party who may use the products for such prohibited purposes. * These products are intended for general use in electronic equipment. When using them in specific applications that require extremely high reliability, such as the applications stated below, you must obtain permission from Seiko Epson in advance. / Space equipment (artificial satellites, rockets, etc.) / Transportation vehicles and related (automobiles, aircraft, trains, vessels, etc.) / Medical instruments to sustain life / Submarine transmitters / Power stations and related / Fire work equipment and security equipment / Traffic control equipment / And others requiring equivalent reliability. 10.Contact us http://www5.epsondevice.com/en/contact/ 5 Page