1 J414.B (1/05)
US 619 674 8100
••
UK 44 1483 401 700
••
France 33 3 84 35 04 04
••
Singapore 65 6287 8998
••
Taiwan 886 2 2698 0228
••
Hong Kong 852 2788 6588
••
http://www.pulseeng.com
10/100 Base-T Electrical Specifications @ 25°C — Operating Temperature 0°C to +70°C
Insertion Return Loss Common Mode
Part RoHS 7Data Turns1EMI2LEDs 3BST Loss (dB MIN) Crosstalk Rejection Hipot
Number Rate Ratios Fingers (L/R) (dB MAX) 100Ω±15Ω(dB MIN) (dB MIN) (Vrms)
TX RX 1-65MHz 1-10MHz 10-30MHz 30-60MHz 60-80MHz 1-30MHz 30-60MHz 60-100MHz 1-50MHz 50-150MHz @60Hz 1 MIN
J00-0014 58100BT 1CT:1 1CT:1 No None Yes -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0042 58100BT 1CT:1 1CT:1 No None No -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0045 58100BT 1CT:1 1CT:1 No G/Y Yes -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0046 58100BT 1CT:1 1CT:1 No G/Y No -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0061 58100BT 1CT:1 1CT:1 Yes None Yes -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0064 58100BT 1CT:1 1CT:1 Yes None No -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0065 5NL 100BT 1CT:1 1CT:1 Yes G/Y Yes -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0066 58100BT 1CT:1 1CT:1 Yes G/Y No -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
J00-0086 58100BT 2CT:1 2CT:1 Yes G/Y No -1 -18 -14 -12 -10 -35 -35 -30 -20 -15 1500
STARJACKTM
1x1 Tab-DOWN RJ45
www.pulseeng.com
Features and Benefits:
RoHS “NL” peak solder rating 260°C, non-RoHS peak solder rating 235°C
For RoHS part, add suffix NL7
Low cost 1x1 Tab-DOWN RJ45 with internal magnetics
Available with or without LEDs
Suitable for CAT 5 & 6 Fast Ethernet Cable or better UTP
Internal magnetics are 100% electrically tested for HI-POT and functionality
Electrical Performance Summary:
Meets IEEE 802.3 specification
350µH minimum OCL with 8mA bias current
High performance for Max EMI suppression for cost-conscious applications
Minimum 1500Vrms isolation per IEEE 802.3 requirement
Description:
10/100 Base-TX RJ45 1x1 Tab-DOWN 8-pin Integ rated Magnetics Connector, without LEDs, designed to support high
v olume cost-conscious consumer applications such as: ADSL modems , Cable modems, STB and Video on Demand.
Notes: 1. Both transmit and receive channels meet IEEE 802.3 specifications.
2. For an explanation of EMI fingers, refer to the mechanical drawing page.
3. LEDs Left/Right: G=green, Y=yellow
4. IEEE802.3i (10Base-T) standard does not require these parts to achieve
350µH minimum OCL with 8mA bias current for 10Base-T parts.
5. AutoMDX compatible 100Base-T and 10Base-T connector modules.
6. Capacitor resistor termination circuit included within these parts.
7. Add suffix “NL” for RoHS compliant parts (e.g. J00-0065 changes to J00-0065NL).
8. Contact Pulse for RoHS compliant part availability.
Mating Force Unmating Force Plug to Jack
Part Number (MAX) (MAX) Durability Retention (MIN)
J00 Series 5 lbs./2.268 kgs. 5 lbs./2.268 kgs. 750 Insertions 20 lbs./9.072 kgs.
RJ45 Durability Testing Rating
10 Base-T Electrical Specifications @ 25°C — Operating Temperature 0°C to +70°C
Insertion Return Loss Common Mode
Part RoHS 7Data Turns1EMI2LEDs 3BST 6Loss (dB MIN) Crosstalk Rejection Hipot
Number Rate Ratios Fingers (L/R) (dB MAX) 100Ω±15Ω(dB MIN) (dB MIN) (Vrms)
TX RX 1-10MHz 1-10MHz 1-10MHz 5MHz @60Hz 1 MIN
J00-0025 4,5 810BT 1CT:2.5 1CT:1 Yes None No -1 -15 -30 -25 1500
J00-0051 4,5 810BT 1CT:2.5 1CT:1 Yes G/Y No -1 -15 -30 -25 1500
J00-0062 4,5 810BT 1CT:2.5 1CT:1 No None No -1 -15 -30 -25 1500
J00-0063 4,5 810BT 1CT:2.5 1CT:1 No G/Y No -1 -15 -30 -25 1500
NOTES: 1.All connector part numbers starting with the series prefix J00 comply
to the above limits. 2. Connector dimensions comply with FCC dimension requirements..
3. MSL - Moisture Sensitivity Level class limits = 1 to 5 (Highest: 1; Lowest: 5).
Part Shield Contact Housing MSL3
Number Material Finish Material Plating Area Solder Area Material Specification Rating
J00 20-40m inches Nickel over Phosphor Nickel underplating and 120µ inches Sn90/Pb10
Series Brass 10-20m inches Brass Bronze selective gold plating 15µ inches over 50µ inches nickel Thermoplastic UL 94 V-0 1
RJ45 Material Specification
STARJACKTM
1x1 Tab-DOWN RJ45
2 J414.B (1/05)
US 619 674 8100
••
UK 44 1483 401 700
••
France 33 3 84 35 04 04
••
Singapore 65 6287 8998
••
Taiwan 886 2 2698 0228
••
Hong Kong 852 2788 6588
••
http://www.pulseeng.com
J00-00XX Series Mechanicals
www.pulseeng.com
Patent Pending
Date Code
Country of Origin
JXXXXXXXX
TM
.545
13,84
LEFT LED
RIGHT LED
.640
16,26
.140
3,56 SHIELD PIN
.290
7,37
.
425
10,80
.020
0,51
.135
3,43
.020
0,51
.125
3,18 .020
0,51
.125
3,18
SIGNAL PINS
HOUSING POST
.850
21,59MAX
.350
8,89
.100
2,54
.120
3,05 .250
6,35
.100
2,54
.024
0,61
.398
10,11
.450
11,43
.620
15,75
.498
12,65
7531
86 42
.003
0,08
8X .035
0,89
2X.064
1,63
4X .040
1,02
2X .128
3,25
11
12 10
9
.193
4,90
.133
3,38
.050
1,27
FRONT
BACK
HOUSING POST
SHIELD PIN
.560
14,22
TOP OF PCB
TO BOTTOM
OF OPENING
.010
0,25
R 2.54
6,45
4X RMAX
.010
0,25
.660
16,76
FRONT VIEW
Viewed from PCB Component side
Connector Marking
(An example - parts are marked on
the top or end surface as shown)
BACK
FRONT
SIDE VIEW
J00-00XX Series Electrical Schematics
TD+ 1
CT 4
TD- 2
RD+ 3
CT 5
RD- 6
7
8
7
4
5
6 RX-
3 RX+
2 TX-
1 TX+
1CT : 1
TRANSMIT
1CT : 1
RECEIVE
CABLE SIDE
PCB SIDE TO PHY
GND* 8
*Connecting pin 8 to Ground makes J00-0042/46/64/66
footprint compatible to J00-0014/45/61/65.
**J00-0086 Turns Ratio TX, RX = 1.414CT:1 ( 2CT:1)
J00-0042/46/64/66/86 J00-0014/45/61/65 J00-0025/51/62/63
0.001mF
1CT : 1
RECEIVE
8
7
4
5
6 RX-
3 RX+
2 TX-
1 TX+
TD+ 1
CT 4
TD- 2
RD+ 3
CT 5
RD- 6
NC 7
8
1CT : 1
TRANSMIT
CABLE SIDE
PCB SIDE TO PHY
CHS
GROUND
75
75
75
75
NOTE: Connect CHS GND to PCB ground.
TD+ 1
CT 7
TD- 2
RD+ 3
CT 8
RD- 6
4
58
7
4
5
6 RX-
3 RX+
2 TX-
1 TX+
1CT : 2.5
TRANSMIT
1CT : 1
RECEIVE
CABLE SIDE
PCB SIDE TO PHY
EMI Fingers Part Number
Location
Green / Yellow LED Specification - (LEDs without internal resistors)
Right LED
12
11
Left LED
9
10
Yellow 585 nm 2.5 V 2.1 V
Green 565 nm 2.5 V 2.2 V
Standard LED Wavelength Forward* V(MAX) (TYP)
* Assumes bias current = 20mA
Dimensions: Inches
mm
Unless otherwise specified,
all tolerances are ± .010
0,25
LED Configuration
STARJACKTM
1x1 Tab-DOWN RJ45
www.pulseeng.com
Application Notes
Increased Reliability
Pulse developed a patented method for ensuring the quality, consis-
tency, and connection integrity of encapsulated coils and other
three-dimensional electronic components. The InterLock Base con-
sists of an internal plastic carrier that holds the coil firmly in place
and provides precisely engineered “lead-channels” to lock together
the lead wires and the leadframe pins. All of the InterLock Base
interconnections are then simultaneously dip soldered,
providing for both efficiency and uniformity for best common mode
rejection and crosstalk.
Higher Manufacturing Yields
Because of this Pulse patented higher reliability method, there is less of
a chance of opens and shorts, thus providing higher yields.
Consistent Electrical and Magnetic Performance
•With internal magnetics specifically oriented on all parts, there
are more consistent readings on all functional tests. This is opti-
mized for best crosstalk, common mode rejection and return loss.
•With the selection of common mode material and winding
techniques, common mode noise rejection maintains integrity at
higher frequencies.
•Multiple tabs around shield-to-ground, shield-to-chassis,
and shunt noise to ground improves EMI suppression.
Advantages of the PulseJack Modules
3 J414.B (1/05)
©2005, Pulse Engineering, Inc. All Rights Reserved.
For More Information:
UNITED STATES
(Worldwide)
12220 World Trade Drive
San Diego, CA 92128
U.S.A.
http://www.pulseeng.com
TEL: 858 674 8100
FAX: 858 674 8262
UNITED KINGDOM
(Northern Europe)
3 Huxley Road
Surrey Research Park
Guildford, Surrey GU2 5RE
United Kingdom
TEL: 44 1483 401700
FAX: 44 1483 401701
FRANCE
(Southern Europe)
Zone Industrielle
F-39270
Orgelet
France
TEL: 33 3 84 35 04 04
FAX: 33 3 84 25 46 41
TAIWAN, R.O.C.
(Northern Asia)
3F-4, No. 81, Sec. 1
HsinTai Wu Road
Hsi-Chih, Taipei Hsien
Taiwan, R.O.C.
Tel: 886 2 2698 0228
FAX: 886 2 2698 0948
SINGAPORE
(Southern Asia)
150 Kampong Ampat
#07-01/02
KA Centre
Singapore 368324
TEL: 65 6287 8998
FAX: 65 6280 0080
HONG KONG
(China/Hong Kong)
Unit 11, 11/F
Wah Lai Industrial Centre
10-14 Kwei Tei Street,
Fotan, Shatin, Hong Kong
TEL: 852 2788 6588
FAX: 852 2776 1055
DISTRIBUTOR
Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product
names mentioned herein may be trademarks or registered trademarks of their respective owners.
