2018 Professional Insulated Tools Supporting Arc Flash Protection 10,000 Volt Tested 1000 Volt Rated #32800 Complete Insulated Program Toll Free: (800) 494-6104 2 Arc Flash Protection: Wiha Insulated tools can be a vital component in your Arc Flash protection strategy. What is Arc Flash? Wiha Insulated Wrenches Description Page Insulated Open End Spanners 4-5 ARC FLASH An Arc Flash is an electrical explosion due to a fault condition or short circuit when either a phase to ground or phase to phase conductor is connected. Arc flashes cause electrical equipment to explode, resulting in an arc-plasma fireball. Temperatures may exceed 35,000 F (the surface of the sun is 9000 F). These high temperatures cause rapid heating of surrounding air and extreme pressures, resulting in an arc blast. The arc blast will likely vaporize all solid copper conductors which will expand up to 67,000 times its original volume when it is vaporized. The result of this violent event is usually destruction of the equipment involved, fire, and severe injury or death to any nearby people. WHY ARC FLASHES HAPPEN There are a variety of reasons why an Arc Flash can occur, but most of them are preventable. Most arc flashes occur when maintenance workers are manipulating live equipment for testing or repair and accidentally cause a fault. Improper tools, improper electrical equipment, corrosion of equipment, improper work techniques and lack of training are just some of the events that can lead to a devastating arc flash or arc blast. ARC FLASH COMPLIANCE There are 4 main regulations that govern electrical safety & arc flash: 1. OSHA Standards 29CFR, Part 1910. Occupational Safety and Health Standards. 1910 sub part S (electrical) Standard number 1910.333 specifically addresses Standards for Work Practices and references NFPA 70E. OSHA 29CFR 1910.335 (a) (1)(i) requires the use of protective equipment when working where a potential electrical hazard exists and 29CFR 1910.132(d)(1) which requires the employer assess the workplace for hazards and the need for personal protective equipment. OSHA compliance is required by any plant building or facility. 2. The National Fire Protection Association (NFPA) Standard 70 2002 "The National Electrical Code" (NEC) contains requirements for warning labels. 3. NFPA 70E provides guidance on implementing appropriate work practices that are required to safeguard workers from injury while working on or near exposed electrical conductors or circuit parts that could become energized. Part II 2-1.3.3 regarding Arc Flash Analysis states that a "Flash Hazard Analysis shall be done before a person approaches any exposed electrical conductor or circuit part that has not been placed in an electrical safe work condition". This Arc Flash Hazard Analysis must be done to determine the level of Personal Protection Equipment PPE that a worker must use, and the Arc Flash Boundary in inches along with the incident energy found at each location. Each panel must be marked with an ANSI z535 approved Arc Flash Warning Label. 4. The Institute of Electronics and Electrical Engineers (IEEE) 1584 - 2002 Guide to Performing Arc-Flash Hazard Calculations copyright (c) information by: American Trainco, Inc. http://www.martinarcflash.com OSHA Wiha tools assists with compliance of OSHA 29CFR 1910 (Sub Parts electrical standard) Insulated Ratchet Wrenches 5 Ins. Offset Ring Wrenches 6 Wiha Insulated Adjustable Wrenches Description Page Insulated Adjustable Wrenches 7 8.0, 10.0, 12.0, 15.0" Wiha Insulated Electrician's Knives Description Page Insulated Knives Wiha Insulated L-keys Description Insulated L-keys 7 Page 8 Wiha Insulated 3/8" Hex Drive Bit Sockets Description Page Ins. Hex Drive Bit Sockets 9 Wiha Insulated Socket Accessories Description Page Insulated Sockets 1/4, 3/8, 1/2" 9-12 Insulated Ratchets 10-13 Insulated T-handle 10-13 Insulated Extension Bars 10-13 Wiha Insulated Cable Cutters & Pliers Description Page Insulated Cable Cutters 13 Insulated WaterPump Pliers 13 www.wihatools.com 3 Wiha Insulated Hacksaw Description Insulated Hacksaw Page 13 Wiha Insulated Pop-Up SlimLine Blade Sets Description Page Insulated Pop-Up Sets 17 Wiha Insulated Pico Finish Screwdrivers Description Page Insulated Slotted Drivers 20 Insulated Phillips Drivers 20 Insulated PicoFinish Sets 20 Wiha Insulated SlimLine Tools Description Page Insulated SlimLine Handles 18 Wiha Insulated Tools Description Page Xeno Terminal Block Combination Screwdrivers 25 Insulated TorqueControl Handle & Blade Holder 17 Voltage Detectors 25 Insulated Hex Inch/Metric T-handles 15 Insulated Slotted Drivers 22-23 Insulated Phillips Drivers 22-23 Insulated Torx(R) Drivers 24 Insulated Nut Drivers 26 Insulated Pozidriv(R) 25 Insulated Square Tip 24 Insulated Tweezers 14 Insulated SlimLine Blade Sets 17-18 Insulated SlimLine Blades Insulated SlimLine Drivers 19 20 Insulated SlimLine Driver Sets 21 Wiha Insulated TorqueControl Tools Description Page Insulated Torque Ratchet 16 Wiha Insulated Pop-Up Insert Bit Sets Description Page Insulated Pop-Up Sets 27 Wiha Insulated Belt Pack Pouch Sets Description Page Insulated Belt Pack Pouches Pliers & Cutters Pliers/Cutters & Screwdrivers Pliers/Cutters & Multi Bit Set Insulated Combination Pliers 36 Insulated Heavy Duty Diagonal Cutters 37 Insulated Pliers 38 Insulated Stripping Pliers 37 Insulated Pliers Sets 28-35 27-28 Wiha Insulated Multi-Bit Holders Description Page Insulated Multi-Bit Drivers Wiha Insulated 1000Volt Pliers/Cutters Description Page 28 Wiha Insulated Inomic Pliers Description Insulated Inomic Pliers Page 39 Inomic Combo Pliers Inomic Long Nose Pliers Inomic Diagonal Cutters Wiha Insulated Industrial Pliers/Cutters Description Page Insulated Industrial Pliers/Cutters 40-44 Toll Free: (800) 494-6104 4 Wiha Insulated Open-End Wrenches Insulation Test Standards: Insulation according to ASTM F-1505, EN/IEC 60900, VDE 0680, DIN 7446 and CSA Angled 15 O Insulation High visibility, grip is double coated Steel Forged from chrome vanadium, meets DIN 3110 1000Volt 20190 14 Piece Insulated Inch Open End Wrench Set Item OAL OAL No. Inch Inch Inch Inch lbs. 20190 5/16 3.9 3/4 7.0 5.70 3/8 4.1 13/16 7.5 7/16 4.6 7/8 7.6 1/2 5.5 15/16 7.9 9/16 5.7 1 8.4 5/8 6.2 1-1/16 9.2 11/16 6.5 1-1/8 9.1 1000Volt 20192 1000Volt 8 Piece Insulated Inch Open End Wrench Set Item OAL OAL No. Inch Inch Inch Inch lbs. 20192 5/16 3.9 9/16 5.7 1.59 3/8 4.1 5/8 6.2 7/16 4.6 11/16 6.5 1/2 5.5 3/4 7.0 1000V Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc 1000Volt 20091 15 Piece Insulated End Wrench Set Item OAL No. mm mm mm 20091 6.0 97 14 7.0 98 15 8.0 104 16 9.0 108 17 10.0 107 19 11.0 118 22 12.0 129 24 13.0 137 Metric Open OAL mm 150 151 164 162 178 196 211 lbs. 3.0 1000Volt 20093 8 Piece Insulated Metric Open End Wrench Set Item OAL OAL No. mm mm mm mm lbs. 6.0 97 13.0 137 1.4 20093 7.0 98 14.0 150 8.0 104 17.0 162 10.0 107 19.0 178 201 Inch Open-End Wrenches, With Insulated Handle Insulation According to VDE Specification 0680 and EN/IEC 60900, DIN 7446 and CSA, up to 1000 Volt. Individually Tested. Chrome-vanadium steel, hardened. Angled 15O. Item OAL OAL No. Inch Inch mm lbs. pkg. 1 1/4 3.4 87.5 .04 20131 1 5/16 3.9 100 .05 20133 1 3/8 4.1 105 .09 20135 1 7/16 4.6 117 .09 20136 1 1/2 5.5 140 .15 20137 1 9/16 5.7 146 .15 20138 1 5/8 6.2 158 .20 20140 1 11/16 6.5 165 .23 20141 1 3/4 7.0 178 .33 20142 1 13/16 7.5 191 .42 20144 1 7/8 7.6 192 .44 20145 1 15/16 7.9 201 .51 20146 1 1 8.4 213 .61 20147 1 1-1/16 9.2 233 .79 20148 1 1-1/8 9.2 233 .77 20149 1 1-1/4" 7.5 20151 1 1-1/2" 7.5 20154 * Lengths are +/- 5% due to coating process 1000Volt 200 Metric Open-End Wrenches, With Insulated Handle Item OAL OAL No. mm mm Inch lbs. pkg. 6.0 97 3.8 .04 1 20006 7.0 98 3.9 .05 1 20007 8.0 104 4.1 .07 1 20008 9.0 108 4.3 .07 1 20009 10.0 107 4.2 .08 1 20010 11.0 118 4.6 .11 1 20011 12.0 129 5.1 .11 1 20012 13.0 137 5.4 .19 1 20013 14.0 150 5.9 .19 1 20014 15.0 151 5.9 .17 1 20015 16.0 164 6.5 .22 1 20016 17.0 168 6.4 .24 1 20017 18.0 173 6.8 .41 1 20018 19.0 178 7.0 .32 1 20019 20.0 190 6.9 .36 1 20020 22.0 196 7.7 .39 1 20022 24.0 211 8.3 .58 1 20024 27.0 218 8.6 .68 1 20027 30.0 235 9.3 .97 1 20030 32.0 237 9.3 1.01 1 20032 www.wihatools.com 5 Wiha Insulated Open-End Wrenches Wiha Insulated Ratchet Wrenches Insulation Test Standards: Insulation according to ASTM F-1505, EN/IEC 60900, ISO 3110 and CSA Specification 1000Volt In Tool Box Tray Steel Forged from chrome vanadium, meets - DIN 3110 Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc 1000V 20194 13 Piece Insulated Inch Open End Wrench Set In Tool Box Tray Item OAL OAL No. Inch Inch Inch Inch lbs. 20194 1/4 3.411/16 6.5 4.90 5/16 3.93/4 7.0 3/8 4.113/16 7.5 7/16 4.67/8 7.6 1/2 5.515/16 7.9 9/16 5.71 8.4 5/8 6.2 In Tool Box Tray 1000Volt 1000Volt Inch Insulated Ratchet Wrenches, 213 With Insulated Handle Insulation According to EN/IEC 60900, ISO 3110 Specification, Up To 1000 Volt. Individually Tested. Blade chrome-vanadium steel, hardened. Item OAL OAL No. Inch mm Inch lbs. pkg. 1 21325 3/8 140 5.5 .14 1 21327 7/16 143 5.6 .15 1 21329 1/2 154 6.1.18 1 21331 9/16 162 6.4.22 1 21333 5/8 177 7.0.30 1 21335 3/4 209 8.2.46 212 Metric Insulated Ratchet Wrenches, With Insulated Handle Insulation According to EN/IEC 60900, ISO 3110 Specification, Up To 1000 Volt. Individually Tested. Blade chrome-vanadium steel, hardened. Item OAL OAL No. mm mm Inch lbs. pkg. 21208 1 8.0 125 4.9 .08 21210 1 10.0 140 5.5 .12 21212 1 12.0 150 5.9 .18 21213 1 13.0 152 6.0 .18 21214 1 14.0 163 6.4 .22 21217 1 17.0 193 7.6 .38 21219 1 19.0 210 8.3 .45 1000Volt 20196 13 Pc. Insulated Metric Open End Wrench Set In Tool Box Tray Item OAL OAL No. mm mm mm mm lbs. 20196 8.0 104 16.0 164 4.90 10.0 107 17.0 168 11.0 118 18.0 173 12.0 129 19.0 178 13.0 137 22.0 196 14.0 150 24.0 211 15.0 151 1000Volt 6 Piece Inch Insulated Ratchet 21391 Wrenches Set Item OAL OAL No. Inch Inch Inch Inch lbs. 3/8 5.5 9/16 6.4 1.95 21391 7/16 5.6 5/8 7.0 1/2 6.1 3/4 8.2 1000Volt 21290 7 Piece Metric Insulated Ratchet Wrenches Set ItemOALOAL No. mm mm mm mm lbs. 8.0 4.9 14.0 6.4 2.10 21290 10.0 5.5 17.0 7.6 12.0 5.9 19.0 8.3 13.0 6.0 Toll Free: (800) 494-6104 6 Wiha Insulated Deep Offset Ring Wrenches Insulation Test Standards: Insulation according to ASTM F-1505, EN/IEC 60900, ISO 3110 and CSA Specification Steel Forged from chrome vanadium, meets - DIN 3110 Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc 1000V 1000Volt 1000Volt 21096 8 Piece Inch Insulated Offset Ring Wrenches Set Item No. Inch: 5/16, 3/8, 7/16, 1/2, 9/16, lbs. 21096 5/8, 11/16, 3/4" 3.20 21094 16 Piece Inch Insulated Offset Ring Wrenches Set Item No. Inch: 21094 1/4, 5/16, 3/8, 7/16, 1/2, lbs. 9/16, 5/8, 11/16, 3/4, 8.70 25/32, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/4" 1000Volt Insulated Inch Offset Ring 210 Wrenches Blade CV steel, hardened. Item No. Inch lbs. pkg. 1/4 .16 1 21040 5/16 .18 1 21042 3/8 .20 1 21044 7/16 .22 1 21046 1/2 .30 1 21048 9/16 .30 1 21050 5/8 .34 1 21052 11/16 .34 1 21054 3/4 .44 1 21056 25/32 .58 1 21057 13/16 .52 1 21058 7/8 .64 1 21060 15/16 .90 1 21062 1.0 .96 1 21064 1-1/16 1.28 1 21066 1-1/4 1.38 1 21068 1000Volt 1000Volt 8 Piece Metric Insulated Offset 21095 Ring Wrenches Set Item No. Metric: 10.0, 11.0, 12.0, 13.0, lbs, 21095 14.0, 15.0, 17.0, 19.0mm 3.20 1000Volt 21093 16 Piece Metric Insulated Offset Ring Wrenches Set Item No. Metric: 21093 8.0, 9.0, 10.0, 11.0, 12.0, 13.0, 14.0, 15.0, 17.0, 19.0, 20.0, 22.0, lbs. 8.70 24.0, 27.0, 30.0, 32.0mm Use & Care Guide For Insulated Tools: Store tools to minimize risk of damage to insulation, always wear approved eye protection, Inspect insulation prior to each use of any insulated tool. Use insulated tools where the ambient temperature is between -20 to +70O C. Have a qualified safety technician visually inspect insulation on tools annually for safe use. Insulated Metric Offset Ring 210 Wrenches, Insulation According to EN/IEC 60900, ISO 3110 Specification, Up To 1000 Volt. Individually Tested. Blade ChromeVanadium steel, hardened. Item OAL OAL No. mm mm Inch lbs. pkg. 1 21008 8.0 159 6.3 .16 1 21009 9.0 159 6.3 .18 1 21010 10.0 171 6.8 .20 1 21011 11.0 178 7.0 .22 1 21012 12.0 191 7.5 .30 1 21013 13.0 194 7.6 .30 1 21014 14.0 203 8.0 .34 1 21015 15.0 203 8.0 .34 1 21017 17.0 219 8.6 .44 1 21019 19.0 241 9.5 .52 1 21020 20.0 250 9.8 .58 1 21022 22.0 257 10.1 .64 1 21024 24.0 279 11.0 .90 1 21027 27.0 286 11.3 .96 21030 30.0 311 12.3 1.28 1 21032 32.0 318 12.5 1.38 1 www.wihatools.com 7 Wiha Insulated Adjustable Wrenches 1000Volt 76208 Insulated 8" Adjustable Wrench Insulation According to ASTM, EN/IEC, NFPA, CSA and ISO Specification, up to 1000 Volt. Individually Tested. Etched on scale for pre-setting size. Slip guard handle for added protection. Item OAL OAL Capacity No. Inch mm Opening lbs. pkg. 8.0 200 1" .7 1 76208 Wiha Insulated Electrician's Knives Insulation Test Standards: Insulation according to ASTM, EN/IEC, VDE & CSA Specification Individually tested Insulation molded on for permanent bonding 1000V Each tool individually tested to 10,000 volts & rated to 1000Volt ac or 1500Volt dc 1000Volt 76210 Insulated 10" Adjustable Wrench Etched on scale for pre-setting size. Slip guard handle for added protection. Item OAL OAL Capacity No. Inch mm Opening lbs. pkg. 1 76210 10.0 250 1-1/4" 1.4 1000Volt 76212 Insulated 12" Adjustable Wrench Etched on scale for pre-setting size. Slip guard handle for added protection. Item OAL OAL Capacity No. Inch mm Opening lbs. pkg. 1 12.0 300 1-1/2" 1.9 76212 1000Volt 15000 Insulated Electrician's Cable Stripping Knife, With Insulated Handle, Insulation According To VDE Specification, Up To 1000 Volt. Individually Tested. Blade tool steel, hardened, molded directly on. Cover included. Item Blade OAL OAL No. mm mm Inch lbs. pkg. 50 216 8.5 .30 1 15000 1000Volt 15050 Insulated Stripping Knife, With Insulated Handle Insulation According To VDE Specification, Up To 1000 Volt. Individually Tested. Blade tool steel, hardened. Insulation molded directly on. Hooked cutting edge, half-round ground. Cover included. Item Blade OAL OAL No. mm mm Inch lbs. pkg. 35 222 8.75 .22 1 15050 1000Volt 76215 Insulated 15" Adjustable Wrench Etched on scale for pre-setting size. Slip guard handle for added protection. Item OAL OAL Capacity No. Inch mm Opening lbs. pkg. 1 76215 15.0 380 1-11/16" 2.8 1000Volt 15003 Insulated Electrician's Cable Stripping Knife, With Insulated Handle, Insulation According To VDE Specification, Up To 1000 Volt. Individually Tested. Straight, partly insulated, strong blade. Insulation molded directly on. Cover included. Item Blade OAL OAL No. mm mm Inch lbs. pkg. 15003 50 230 9.0 .23 1 1000Volt 3 Pc. Insulated Adjustable 76290 Wrenches Etched on scale for pre-setting size. Slip guard handle for added protection. Item No. Set includes the following: 76290 8.0", 10.0", 12.0" Adjustable Pliers lbs. 4.0 WARNING! Insulated Tools are intended to provide protection against accidental contact with charged energized circuits. For maximum safety we recommend de-energizing all circuits whenever possible before starting work on electrical apparatus or conductors. Always visually inspect insulation on tools before use, do not use tools if insulation shows signs of wear or damage to the insulated areas of the tool. Wear appropriate eye protection when using hand tools. Use NFPA70E certified insulated protective outer wear when appropriate. Toll Free: (800) 494-6104 8 Wiha Insulated Hex L-keys 1000Volt 136 Inch Insulated Hex L-keys, With Insulated Handle. Insulation According to IEC 60900 Specification, Up To 1000 Volt. Individually Tested. Blade chrome-vanadium steel, hardened. Item OAL OAL No. Inch mm Inch lbs. pkg. 13670 1/16 79 3.1 .05 1 13671 5/64 84 3.3 .05 1 13672 3/32 89 3.5 .05 1 13673 7/64 94 3.7 .06 1 13663 1/8 104 4.1 .06 1 13665 5/32 104 4.1 .06 1 13666 3/16 134 5.3 .10 1 13667 7/32 134 5.3 .12 1 13668 1/4 134 5.3 .16 1 13669 5/16 144 5.7 .24 1 13662 3/8 234 9.2 .51 1 13664 1/2 234 9.2 .77 1 Insulation Test Standards: Insulation according to ASTM, F-1505, EN/IEC 60900 and CSA Insulation Applied directly onto blade for permanent bonding 1000V Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc 1000Volt 1000Volt 8 Piece Insulated Inch Hex 13690 L-key Set Item OAL OAL No. Inch Inch Inch Inch lbs. 1/8 4.1 1/4 5.3 2.17 13690 5/32 4.1 5/16 5.7 3/16 5.3 3/8 9.2 7/32 5.3 1/2 9.2 13694 12 Pc. Insulated Inch Hex L-key Set Item OAL OAL No. Inch Inch Inch Inch lbs. 13694 1/16 3.1 3/16 5.3 2.40 5/64 3.3 7/32 5.3 3/32 3.5 1/4 5.3 7/64 3.7 5/16 5.7 1/8 4.1 3/8 9.2 5/32 4.1 1/2 9.2 1000Volt 1000Volt 136 Metric Insulated Hex L-keys, With Insulated Handle. Insulation According to IEC 60900 Specification, Up To 1000 Volt. Individually Tested. Blade chrome-vanadium steel, hardened. Item OAL OAL No. mm mm Inch lbs. pkg. 1.5 100 3.9 .09 13650 1 2.0 105 4.1 .09 13651 1 2.5 115 4.5 .09 13652 1 3.0 130 5.1 .10 13653 1 4.0 120 4.7 .10 13654 1 5.0 140 5.5 .10 13655 1 6.0 140 5.5 .13 13656 1 8.0 150 5.9 .24 13658 1 10.0 220 8.7 .51 13659 1 12.0 260 10.2 .77 13657 1 1000Volt 7 Piece Insulated Metric Hex 13691 L-key Set Item No. mm 13691 3.0 4.0 5.0 6.0 OAL OAL mm mm mm lbs. 130 8.0 150 2.07 120 10.0 220 140 12.0 260 140 13693 10 Piece Insulated L-key Set Item OAL No. mm mm mm 1.5 100 5.0 13693 2.0 105 6.0 2.5 115 8.0 3.0 130 10.0 4.0 120 12.0 Metric Hex OAL mm 140 140 150 220 260 lbs. 2.26 www.wihatools.com 9 Wiha Insulated Hex Bit Sockets Wiha Insulated Socket Adapters / Reducers 1000Volt 1000Volt 318 Insulated 3/8" Drive Sockets Chrome-vanadium steel, forged, oil-hardened. Item OAL No. Inch Inch lbs. pkg. 31805 3/16 3.1" .13 1 31807 7/32 3.1" .14 1 31809 1/4 3.1" .14 1 31811 5/16 3.1" .16 1 31813 3/8 3.1" .18 1 31815 7/16 3.1" .20 1 31817 1/2 3.1" .22 1 *Sockets must be used with insulated ratchets & extensions #31450 #31460 Insulated Socket Adapters / Reducers CV steel, forged, oil-hardened. Item No. Size lbs. pkg. 1/4 - 3/8 . 1 31350 3/8 - 1/2 . 1 31450 3/8 - 1/4 . 1 31460 1/2 - 3/8 . 1 31650 #31650 Wiha Insulated 1/4" Sockets, Accessories & Sets Metric 6 Point 1000Volt Metric 6 Point 1000Volt 31890 7 Pc. Insulated 3/8" Drive Socket Set - Inch CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 31890 3/16, 7/32, 1/4, 5/16, 3/8, lbs. 1.7 7/16, 1/2" 1000Volt 318 Insulated 1/2" Drive Sockets Chrome-vanadium steel, forged, oil-hardened. Item OAL No. Inch Inch lbs. pkg. 1/4 2.75 .22 1 31830 5/16 2.75 .24 1 31832 3/8 2.75 .25 1 31834 7/16 3.63 .31 1 31836 1/2 3.63 .34 1 31838 9/16 3.63 .36 1 31840 5/8 3.63 .42 1 31842 3/4 3.63 .51 1 31844 1000Volt 313 Insulated 1/4" Drive Sockets-6 Point, Insulation According To ASTM F-1505, DIN 7448 & CSA Specification, Up To 1000 Volt. Individually Tested. Chromevanadium steel, forged, oil-hardened. Item No. Inch lbs. pkg. 31336 3/16 .03 1 31337 7/32 .03 1 31338 1/4 .03 1 31339 9/32 .04 1 31340 5/16 .04 1 31341 11/32 .05 1 31342 3/8 .05 1 31343 7/16 .06 1 31344 1/2 .07 1 31345 9/16 .07 1 313 Insulated 1/4" Drive Sockets-6 Point, Insulation According Chrome-vanadium steel, forged, oil-hardened. Item No. mm lbs. pkg. 31326 5.0 .03 1 31327 6.0 .03 1 31328 7.0 .03 1 31329 8.0 .04 1 31330 9.0 .04 1 31331 10.0 .05 1 31332 11.0 .05 1 31333 12.0 .06 1 31334 13.0 .06 1 31335 14.0 .07 1 *Sockets must be used with insulated ratchets & extensions *Sockets must be used with insulated ratchets & extensions 1000Volt 1000Volt *Sockets must be used with insulated ratchets & extensions 31390 13 Pc Insulated 1/4" Drive Socket Set - Inch CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 31390 3/8, 7/16, 1/2, 9/16" lbs. 1.39 1/4" x 50mm Extension Bar 1/4" x 100mm Extension Bar 1/4" Ratchet - 140mm 31391 13 Pc. Insulated 1/4" Drive Socket Set - Metric CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 31391 5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm 1/4" x 50mm Extension Bar lbs. 1/4" x 100mm Extension Bar 1.41 1/4" Ratchet - 140mm Toll Free: (800) 494-6104 10 Wiha Insulated 1/4" Sets & Accessories Wiha Insulated 3/8" Sockets 1000Volt 1000Volt 31394 11 Pc. Insulated 1/4" T-handle & Socket Set-Inch CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 31394 3/16, 7/32, 1/4, 9/32, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16" lbs. 1.40 Insulated 1/4" T-handle Each tool individually tested to 10,000 volts & certified to 1000Volt ac or 1500Volt dc 1000Volt 31395 11 Piece Insulated 1/4" T-handle & Socket Set - Metric CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm 31395 lbs. 1.40 Insulated 1/4" T-handle 1000Volt Insulated 1/4" Drive Ratchet, 12851 EN/IEC 60900 & CSA Chrome-Vanadium steel. Thumb lever for rapid reverse. Item OAL OAL No. Inch mm Inch lbs. pkg. 12851 1/4" 140 5.5 .28 1 1000Volt 29006 Insulated 1/4" Drive T-handle, With Insulated Handle. Insulation according to EN/IEC 60900 & CSA specification, up to 1000 Volt. Individually Tested. Blade CV steel, hardened. Item OAL OAL No. Inch mm Inchlbs. pkg. 29006 1/4 160 6.2".57 1 1000Volt 128 Insulated 1/4" Extension Bars, ASTM F-1505, EN/IEC 60900 & CSA Chrome-Vanadium steel. Item OAL OAL No. Inch mm Inch lbs. pkg. 12854 1/4" 50 2.0 .08 1 12855 1/4" 100 3.9 .12 1 314 Insulated 3/8" Drive Sockets Insulation according to EN/IEC 60900, DIN 7448 & CSA specification, up to 1000 Volt. Individually Tested. CV steel, forged, oil-hardened. Item No. Inch lbs. pkg. 31425 1/4 .07 1 31428 9/32 .07 1 31429 5/16 .07 1 31430 11/32 .07 1 31431 3/8 .08 1 31432 7/16 .08 1 31433 1/2 .10 1 31434 9/16 .10 1 31435 5/8 .10 1 31436 11/16 .13 1 31437 3/4 .14 1 31438 13/16 .17 1 31439 7/8 .18 1 *Sockets must be used with insulated ratchets & extensions 1000Volt Insulated 3/8" Drive Sockets315 Metric Insulation according to VDE, EN/IEC 60900, DIN 7448 & CSA specification, up to 1000 Volt. Individually Tested. Chromevanadium steel, forged, oil-hardened. Item No. mm lbs. pkg. 6.0 .07 1 31506 7.0 .07 1 31507 8.0 .07 1 31508 9.0 .07 1 31509 10.0 .07 1 31510 11.0 .08 1 31511 12.0 .10 1 31512 13.0 .10 1 31513 14.0 .10 1 31514 15.0 .10 1 31515 16.0 .10 1 31516 17.0 .11 1 31517 18.0 .12 1 31518 19.0 .14 1 31519 20.0 .15 1 31520 21.0 .17 1 31521 22.0 .18 1 31522 24.0 .26 1 31524 *Sockets must be used with insulated ratchets & extensions www.wihatools.com 11 Wiha Insulated 3/8" Sockets & Sets 1000Volt 1000Volt 1000Volt 31493 10 Pc. Insulated 3/8" Drive Socket Set - Inch CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 5/16, 3/8, 7/16, 1/2, 31493 9/16, 5/8, 11/16, 3/4" lbs. 2.50 3/8" x 125mm Extension Bar 3/8" Ratchet - 190mm 31495 24 Pc. Insulated 3/8" Drive Socket Set - Inch CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 31495 1/4, 9/32, 5/16, 11/32, 3/8, 7/16 1/2, 9/16, 5/8,11/16, 3/4" Sockets lbs. 3/8" x 125mm Extension Bar 9.07 3/8" x 250mm Extension Bar 3/8" Ratchet - 190mm Insulated Electrician's Knife - 50mm Slotted: 3.5, 4.5, 6.5mm Phillips: #1, 2, 3 6.3" Long Nose Pliers 8.0" Combo Pliers 6.3" Diagonal Cutters *Sockets must be used with insulated ratchets & extensions 1000Volt 1000Volt 31590 10 Pc. Insulated 3/8" Drive Socket Set - Metric CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 31590 8, 10, 11, 12, 13, 14, 17, 19mm 3/8" x 125mm Extension Bar lbs. 2.50 3/8" Ratchet - 190mm 1000Volt 31592 24 Pc. Insulated 3/8" Drive Socket Set - Metric CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 6, 7, 8, 9, 10, 11, 12, 31592 13, 14, 17, 19mm Sockets lbs. 3/8" x 125mm Extension Bar 9.08 3/8" x 250mm Extension Bar 3/8" Ratchet - 190mm Insulated Electrician's Knife - 50mm Slotted: 3.5, 4.5, 6.5mm Phillips: #1, 2, 3 6.3" Long Nose Pliers 8.0" Combo Pliers 6.3" Diagonal Cutters *Sockets must be used with insulated ratchets & extensions 31496 10 Pc. Insulated 3/8" T-handle & Socket Set-Inch CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 31496 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4" lbs. 2.47 3/8" x 125mm Extension Bar Insulated 3/8" T-handle 31595 10 Pc. Insulated 3/8" T-handle & Socket Set - MM CV steel, forged, oil-hardened sockets. Insulated after EN/IEC 60900. Item No. Set includes the following: 31595 8, 10, 11, 12, 13, 14, 17, 19mm 3/8" x 125mm Extension Bar lbs. 2.47 Ins. 3/8" T-handle Wiha Insulated 3/8" Socket Accessories 1000Volt 128 Insulated 3/8" Extension Bars, EN/IEC 60900 Chrome-Vanadium steel. Item OAL OAL No. Inch mm Inchlbs. pkg. 12856 3/8" 125 4.9.41 1 12857 3/8" 250 9.8.57 1 #29009 1000Volt #12327 16 Piece Insulated 3/8" Drive 31491 Socket Set - Inch/Metric CV steel, forged, oilhardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 31491 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4" lbs. 2.01 8, 10, 11, 12, 13, 14, 17, 19mm 1000Volt 12852 Insulated 3/8" Drive Ratchet, EN/IEC 60900 CV steel. Socket release button. Thumb lever for rapid reverse. Item OAL OAL No. Inch mm Inch lbs. pkg. 3/8" 190 7.5 .93 1 12852 1000Volt Insulated 3/8" Drive T-handle Or Breaker Bar. Insulation according to EN/IEC 60900 specification, up to 1000Volt Rated. Individually Tested. Blade chromevanadium steel, hardened. Item OAL OAL No. Inch mm Inch lbs. pkg. 3/8 200 7.9" .55 1 29009 3/8 216 8.5" .681 12327 Toll Free: (800) 494-6104 12 Wiha Insulated 1/2" Sockets & Sets 1000Volt Inch 1000Volt Insulated 1/2" Drive Sockets 317 Insulation According to ASTM, DIN & CSA Specification, Up To 1000Volt. Individually Tested. CV steel, forged, oil-hardened. Item No. Inch lbs. pkg. 5/16 .16 1 31703 11/32 .16 1 31704 3/8 .16 1 31705 7/16 .16 1 31707 1/2 .16 1 31708 9/16 .17 1 31709 5/8 .19 1 31710 11/16 .19 1 31712 3/4 .21 1 31713 13/16 .23 1 31714 7/8 .27 1 31715 15/16 .35 1 31716 1 .33 1 31718 1-1/8 .44 1 31720 1-1/4 .58 1 31722 1000Volt 31790 24 Piece Insulated 1/2" Drive Socket Set - Inch CV steel, forged, oilhardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 31790 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1" Sockets 1/2" x 125mm Extension Bar lbs. 1/2" x 250mm Extension Bar 11.41 1/2" Ratchet - 260mm Ins. Electrician's Knife - 50mm Slotted: 3.5, 4.5, 6.5mm Phillips: #1, 2, 3 6.3" Long Nose Pliers 8.0" Combo Pliers 6.3" Diagonal Cutters 31792 14 Pc. Insulated 1/2" Drive Socket Set - Inch CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 31792 3/4, 13/16, 7/8, 15/16, 1" lbs. 1/2" x 125mm Extension Bar 7.64 1/2" x 250mm Extension Bar 1/2" Ratchet - 190mm *Sockets must be used with insulated ratchets & extensions Individually Tested 1000Volt Insulated 1/2" Drive Sockets 316 Metric 1000 Volt. Item No. mm lbs. pkg. 31608 8.0 .15 1 31609 9.0 .15 1 31610 10.0 .16 1 31611 11.0 .16 1 31612 12.0 .16 1 31613 13.0 .17 1 31614 14.0 .17 1 31615 15.0 .17 1 31616 16.0 .19 1 31617 17.0 .19 1 31618 18.0 .20 1 31619 19.0 .21 1 31620 20.0 .25 1 31621 21.0 .25 1 31622 22.0 .28 1 31623 23.0 .29 1 31624 24.0 .30 1 31626 26.0 .37 1 31627 27.0 .41 1 31628 28.0 .44 1 31630 30.0 .51 1 31632 32.0 .55 1 *Sockets must be used with insulated ratchets & extensions Each tool individually tested to 10,000 volts & certified to 1000Volt ac or 1500Volt dc Metric 1000Volt 31691 24 Piece Insulated 1/2" Drive Socket Set - Metric CV steel, forged, oilhardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 8, 9, 10, 12, 13, 14, 15, 17, 31691 19, 22, 24mm Sockets 1/2" x 125mm Extension Bar lbs. 1/2" x 250mm Extension Bar 11.39 1/2" Ratchet - 260mm Ins. Electrician's Knife - 50mm Slotted: 3.5, 4.5, 6.5mm Phillips: #1, 2, 3 6.3" Long Nose Pliers 8.0" Combo Pliers 6.3" Diagonal Cutters 1000Volt 31694 14 Pc. Insulated 1/2" Drive Socket Set - Metric CV steel, forged, oilhardened sockets. Insulated to EN/IEC 60900. Item No. Set includes the following: 8, 9, 10, 11, 12, 13, 14, 31694 17, 19, 22, 24mm lbs. 1/2" x 125mm Extension Bar 7.64 1/2" x 250mm Extension Bar 1/2" Ratchet - 190mm Each tool individually tested to 10,000 volts & certified to 1000Volt ac or 1500Volt dc www.wihatools.com 13 Wiha Insulated 1/2" Socket accessories Wiha Insulated Hacksaw Insulated Cable Cutters 1000Volt 1000Volt Uses standard 12" blade 12853 Insulated 1/2" Drive Ratchet, IEC/EN 60900 & CSA Chrome-Vanadium steel. Reversible. Item OAL OAL No. Inch mm Inch lbs. pkg. 12853 1/2" 260 10.2 1.55 1 1000Volt 128 Insulated 1/2" Extension Bars, EN/IEC 60900 & CSA Chrome-vanadium steel. Item OAL OAL No. Inch mm Inch lbs. pkg. 1/2" 125 4.9.45 1 12858 1/2" 250 9.8.91 1 12859 1000Volt Insulated 1/2" Drive T-handle, 29012 With Insulated Handle. Insulation according to EN/IEC 60900 & CSA Specification, Up To 1000 Volt. Individually Tested Blade VC steel, hardened. Item OAL OAL No. Inch mm Inch lbs. pkg. 29012 1/2 200 7.9".68 1 1000Volt Hacksaw, With Insulated Handle 19767 Insulation According to EN/IEC 60900, DIN ISO, ASTM & CSA Specification, Up To 1000 Volt. Individually Tested. Item OAL OAL No. mm Inch lbs. pkg. 19767 457mm 18.0" 1.92 1 Insulated Waterpump Pliers For cutting solid aluminum & copper conductors 11950 Cable Cutter, With Insulated Handle. Insulation According to EN/IEC, ASTM & CSA Specification, Up To 1000 Volt. Individually Tested. Blade alloyed tool steel. Induction hardened. Item OAL OAL Capacity No. mm Inch mm Inch lbs. pkg. 500 19.6 12 1/2" 3.0 1 11950 For cutting multi strand aluminum & copper cables 31.5" 1000Volt 29240 Waterpump Pliers, With Insulated Handle. Insulation According to EN/IEC 60900, DIN ISO 8976, ASTM F-1505 & CSA Specification, Up To 1000 Volt. Individually Tested Box joint. Chromevanadium steel, drop forged, oil hardened. Item OAL OAL Capacity No. mm Inch mm lbs. pkg. 240 9.5 7/8" 1.1 29240 1 1000Volt 40800 Large Capacity Cable Cutter, With Insulated Handle Insulation According to EN/IEC 60900, ASTM F-1505 & CSA Specification, Up to 1000 Volt. Individually Tested. Easy cutting blades, dropped forged, oil hardened. Cuts cable diameters up to 50mm. Not to be used on steel rods. Item OAL OAL Capacity No. mm Inch mm Inch lbs. pkg. 40800 800 31.5 50 2" 8.0 1 For cutting solid aluminum, copper & medium hard wires 1000Volt 1000Volt 12326 Insulated 1/2" Drive Breaker Bar, IEC/EN 60900 & CSA Chrome-Vanadium steel. Item OAL OAL No. Inch mm Inch lbs. pkg. 12326 1/2" 267 10.5 1.04 1 End Cutters, With Insulated 29250 Handle. Insulation According to EN/IEC 60900, DIN ISO 8976, ASTM F-1505 & CSA Specification. Individually Tested. Blade alloyed tool steel. Induction hardened. Item OAL OAL Capacity No. mm Inch mm lbs. pkg. 29250 1 250 10 7/8" 1.1 Toll Free: (800) 494-6104 14 Wiha Insulated Ratcheting Cable Cutters Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc Wiha Insulated Serrated Tweezers Meets EN/IEC Insulation Standards Slip guards at tips for user safety Two layer high contrast insulated coatings 1000Volt 119 High Voltage Double-Insulated Ratcheting Cable Cutters High leverage ratchet cable cutter with shear type blades cuts stranded and flexible copper and aluminum cable. Not for use on steel. Features built in safety release in all cutting positions, and high-visibility comfort grip handles. Item OAL OAL up to Inch No. mm Inch MCM Dia. Cap. lbs. 250 10.0" 500 1.25" 32ml 1.6 11960 280 11.0" 750 2.0" 52ml 2.0 11975 10,000 Volt tested 1000Volt rated 1000Volt 75205 Insulated Serrated Straight Fine Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 130 5.0.06 1 75205 Carbon steel with chrome nickel plated 1000V 1000Volt 75220 Insulated Serrated Straight Blunt Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 75220 200 8.0 .18 1 1000Volt Insulated ACSR Ratcheting 11980 Cable Cutter Replaceable tool steel cutting blades are securely mounted for accurate cutting. Handles lock in closed position for easier storage. High leverage ratchet mechanism for best cutting performance. Item OAL OAL up to Inch No. mm Inch MCM Dia. Cap. lbs. 11980 353 13.9 477 1.25" 32ml 3.42 1000Volt 75210 Insulated Serrated Straight Blunt Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 75210 130 5.0 .08 1 1000Volt 75215 Insulated Serrated Straight Blunt Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 75215 145 6.0 .10 1 1000Volt 75302 Insulated Serrated Angled Fine Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 75302 145 6.0 .08 1 1000Volt 75304 Insulated Serrated Angled Blunt Tip Tweezers, IEC/EN 60900 & CSA Standards, 10,000 Volt Tested Item OAL OAL No. mm Inch lbs. pkg. 75304 200 8.0 .16 1 www.wihatools.com 15 Wiha Insulated T-handle Hex Drivers Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, VDE 0682/part 201, DIN 7437, NFPA70E & CSA specification Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc Responds to OSHA's use specification 29 CFR1910 Blade CVM tool steel, hardened to average 58/60RC Insulation Molded directly onto blade for permanent bonding 1000Volt 1000Volt 334 Inch T-handle, With Wiha-Molded Handle. Blade CVM steel, hardened. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component. Item No. Inch Inch Inch mm lbs. pkg. 33481 5/32 5.9 6.9 176 .09 10 33482 3/16 5.9 6.9 176 .15 10 33483 7/32 5.9 6.9 176 .19 10 33485 1/4 5.9 7.1 176 .20 10 33486 5/16 5.9 7.1 176 .26 10 33487 3/8 5.9 7.1 176 .44 10 33490 Item No. 33490 6 Piece Inch T-handle Hex Set Inch: 5/32, 3/16, 7/32, lbs. 1/4, 5/16, 3/8" 1.66 1000Volt 1000Volt 334 Metric T-handle, With Wiha-Molded Handle. Blade CVM steel, hardened. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component. Item No. mm mm Inch mm Inch lbs. pkg. 33441 4.0 150 5.9 176 6.9 .09 10 33443 5.0 150 5.9 182 7.1 .15 10 33445 6.0 150 5.9 182 7.1 .18 10 33447 8.0 150 5.9 182 7.1 .26 10 33449 10.0 150 5.9 191 7.5 .46 10 Wiha Insulated T-handle Metric Nut Drivers 1000Volt 336 Metric T-handle Nut Drivers, With Wiha-Molded Handle. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000Volt. Individually Tested. Blade CVM steel, hardened. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component. Item No. mm mm Inch mm Inch lbs. pkg. 8.0 200 7.9 232 9.1 .15 5 33632 10.0 230 9.0 262 10.3 .18 5 33634 13.0 230 9.0 262 10.3 .26 5 33637 17.0 230 9.0 268 10.6 .46 5 33641 5 Piece Metric T-handle Hex Set 33478 Item Metric: No. 4.0, 5.0, 6.0, lbs. 33478 8.0, 10.0mm 1.20 Toll Free: (800) 494-6104 16 Wiha Insulated Torque Ratchet Wrenches #30138 Wiha Insulated TorqueControl & SlimLine Tool Sets In Roll-up Pouch In Roll-up Pouch 1000Volt With Certificate of Calibration 1000Volt #30114 1000Volt Insulated Torque Ratchet 301 Wrenches, 1/4, 3/8, 1/2" Drives Insulated to EN/IEC 60900:2004, ASTM F1505, CSA Standards Visible reading scale for easy reading and adjustment. Locking endcap Torque adjuster for easy adjustment. Accuracy +/- 10%. Dual scale reading Ft. lbs. / Nm. Item OAL OAL No. Inch mm Inch Nm lbs. pkg. 30114 1/4" 210 8.25 5-25 1.02 1 30138 3/8" 370 14.5 5-50 2.72 1 30152 1/2" 530 21.0 40-220 3.64 1 Certified to EN ISO 6798, BS EN 26789, ASME B107.14M Specifications 28792 16 Piece Insulated TorqueControl Set With SlimLine Blades Certified to EN ISO 6798, BS EN 26789, ASME B107.14M. Set includes Insulated multicomponent adjustable TorqueVario-S handle, 13 SlimLine blades, SlimLine blade holder & Torque adjustment tool. Item No. 28792 SlimLine Slotted: 4.0, 5.5, 6.5mm SlimLine Phillips: #1, 2 SlimLine Terminal Xeno: #1, 2 SlimLine : T8, T10, T15, T20 SlimLine Square: #1, 2 28727 - Handle Range 18-62 Inch/lbs. SlimLine Blade Holder lbs. 1.27 With Certificate of Calibration Wiha Insulated Torque Ratchet Wrench Sets 28791 8 Piece Insulated TorqueControl Set With Slotted & Phillips SlimLine Blades Set includes Insulated multi-component adjustable TorqueVario-S handle, 5 SlimLine blades, SlimLine blade holder & Torque adjustment tool. Item No. Slotted: 3.0, 4.0, 5.5mm Phillips: #1, 2 28791 28726-Handle Range 10-50 Inch/lbs. lbs. .87 Wiha Insulated TorqueControl Tools * Includes Certificate * Includes SlimLine blade holder #28350 * Requires SlimLine Blades 1000Volt 1000Volt 1000Volt 30190 30192 16 Pc. Insulated 3/8" Drive Ratcheting Torque Wrench & Socket Set Inch CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Inch 3/8" Drive Sockets: 1/4, 9/32, 5/16, 11/32, 3/8, 7/16 30190 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8" lbs. 3/8" x 125mm Extension Bar 8.80 3/8" x 250mm Extension Bar 3/8" Drive Ratcheting Torque Wrench - 5-50 Nm 16 Pc. Insulated 3/8" Drive Ratcheting Torque Wrench & Socket Set Metric CV steel, forged, oil-hardened sockets. Insulated to EN/IEC 60900. Item No. Metric 3/8" Drive Sockets: 8, 9, 10, 11, 12, 13, 14, 15, 16, 30192 17, 18, 19, 20mm lbs. 3/8" x 125mm Extension Bar 8.80 3/8" x 250mm Extension Bar 3/8" Drive Ratcheting Torque Wrench - 5-50 Nm *Sockets must be used with insulated ratchets & extensions *Sockets must be used with insulated ratchets & extensions 287 Insulated TorqueVario-S, With Window Scale Insulation up to 1000Volt EN/IEC, EN ISO, BS EN, ASME & CSA, +/- 6% Accuracy. Ergonomic multi-component handle, light & compact. Handle sizes proportioned to optimize torque range. Audible & perceptible click when torque setting has been attained. In Plastic Tube Holder Item Range No. Inch lbs. Increments mm lbs. pkg. 5 - 18 .5 In/lbs 126-131 .56 1 28750 10 - 50 2 In/lbs 133-138 .74 1 28751 18 - 62 2 In/lbs 137-142 .84 1 28752 287 Insulated TorqueVario-S Handle - In Newton Meter Scale Item Range No. Nm mm lbs. pkg. 0.5 - 2.0 131 .64 1 28740 1.0 - 5.0 138 .56 1 28741 2.0 - 7.0 142 .84 1 28742 Each TorqueVario handle has unique serial number & certificate of calibration www.wihatools.com 17 Wiha Insulated TorqueControl Tools Wiha Cushion Grip Stubby SlimLine Blade Holder & Set Wiha Insulated Pop-Up SlimLine Sets Includes Certificate 1000Volt *Requires SlimLine blade holder #28350 287 Insulated TorqueVario-S, With Window Scale Insulation up to 1000Volt. EN/IEC 60900 EN ISO 6798, BS EN 26789, ASME B107.14M &CSA, +/- 6% Accuracy. Ergonomic multi-component handle, light & compact. Handle sizes proportioned to optimize torque range. Audible & perceptible click when torque setting has been attained. Item Range lbs. pkg. No. Inch lbs. Increments mm 1 5 - 18 .5 In/lbs 126-131 .43 28724 1 10 - 50 2 In/lbs 133-138 .40 28726 1 18 - 62 2 In/lbs 137-142 .69 28727 287 Insulated TorqueVario-S Handle In Newton Meter Scale Item Range No. Nm mm lbs. pkg. 28734 0.5 - 2.0 131 .45 1 28736 1.0 - 5.0 138 .45 1 28738 2.0 - 7.0 142 .72 1 Each TorqueVario handle has unique serial number & certificate of calibration 1000Volt 28350 Insulated SlimLine Torque Blade Holder Chrome-vanadium-molybdenum steel. Through hardened black finish. ClicFix quick release holder securely locks bits. Item OAL OAL No. mm mm Inch lbs. pkg. 28350 6.0 170 6.75 .06 1 Meets VDE, EN/IEC, ASTM, CSA, NFPA specifications 1000Volt 283 Insulated Easy-TorqueControl Adapters Ideal for torque sensitive terminations. For use with SlimLine blades. Repeatable accuracy to +/- 10% Item OAL OAL No. Nm In/lbs mm Inch lbs. pkg. 28366 0.8 7.0 60 2.38 .13 1 28367 2.0 17.7 60 2.38 .13 1 28368 2.5 23.1 60 2.38 .13 1 28369 2.8 24.7 60 2.38 .13 1 28371 4.0 35.4 60 2.38 .13 1 Blades High quality CV steel, through-hardened 1000Volt 28302 SlimLine Stubby Blade Holder, With Wiha-SoftFinish(R) Handle. Insulation According to VDE, ASTM, EN/IEC, NFPA70E & CSA, up to 1000 Volt. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Size mm Inch lbs. pkg. 1/4" 57 2.2 .11 1 28302 Friction hold blade holder securely holds blades in place for precise fastening 1000Volt Rated 10,000 Volt Tested Certified to VDE, EN ISO, BS EN, ASME specifications "Apprentice" 1000Volt 28396 20 Piece Insulated SlimLine Blade Set High quality CV steel, through hardened. Friction hold, stubby cushion grip handle. In zipper case. Item No. Slotted: 3.0, 3.5, 4.0, 5.5mm 28396 Phillips: #1, #2 lbs. Xeno SL/PH: #1, #2 .85 Xeno SL/PZ: #1, #2 : T8, T10, T15, T20 Square: #1, #2 Hex Metric: 3.0, 4.0, 5.0mm SlimLine Stubby Blade Holder 28393 Insulated Pop-Up "Apprentice" Blade Holder Set With SlimLine Blades Insulated cushion grip multi-component handle. Friction hold bit holder holds SlimLine Blades securely. Convenient rotating cap. 28393 Set includes the following blades: Slotted: 3.0, 4.0, 5.5, 6.5mm Phillips: #1, #2 lbs. .38 1000Volt "Residental" Insulated Pop-Up "Residental" 28394 Blade Holder Set With SlimLine Blades 28394 Set includes the following blades: Slotted: 3.0, 4.0mm Phillips: #1, #2 Square: #1, #2 lbs. .38 1000Volt "MRO" Insulated Pop-Up "MRO" Blade 28395 Holder Set With SlimLine Blades 28395 Set includes the following blades: Slotted: 3.0, 4.0mm Phillips: #1, #2 Terminal Xeno: #1, #2 lbs. .38 Each SlimLine bit can be taken in and out of the holder easily and conveniently Toll Free: (800) 494-6104 18 Wiha Cushion Grip SlimLine Blade Holder Wiha Insulated SlimLine Blade Sets 1000Volt 1000Volt 1000Volt 8 Piece Insulated SlimLine Blade 28391 Set High quality CV steel, through hardened. Cushion grip. Friction hold blade holder, holds blades securely. Up to 33% narrower insulation diameter then standard insulated tools. In roll up pouch Item No. Slotted: 4.0, 6.5 28391 Phillips: #1, #2 Xeno SL/PH: #2 lbs. .45 : T15, T20 28301 - SlimLine Blade Holder 12 Piece Insulated SlimLine 28392 Blade Set High quality CV steel, through hardened. Cushion grip. Friction hold blade holder, holds blades securely. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. In roll up pouch Item No. Slotted: 3.0, 5.5mm Phillips: #2 28392 Xeno SL/PH: #1, #2 lbs. Square: #1, #2 .52 : T8, T10, T15, T20 28301 - SlimLine Blade Holder 1000Volt 28301 SlimLine Blade Holder, With Wiha-SoftFinish(R) Handle Insulation According to VDE, ASTM F-1505 and EN/ IEC 60900, NFPA70E & CSA, up to 1000 Volt. Chrome-vanadium steel, throughhardened. Insulation molded directly onto blade. Friction hold blade holder, holds blades securely. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Size mm Inch mm Inch lbs. 1/4" 50 2.0 160 6.3 .15 28301 33% Narrower Insulation Diameter Slim Diameter 1000Volt 28399 30 Piece Insulated SlimLine Blade Set High quality CV steel, through hardened. Friction hold blade holder, holds blades securely. In belt wallet storage pouch. Item No. Slotted: 2.5, 3.0, 3.5, 4.0, 5.5, 6.5mm Phillips: #1, #2 28399 Pozidriv(R): #1, #2 lbs. Xeno SL/PH: #1, #2 1.20 Xeno SL/PZ: #1, #2 : T8, T9, T10, T15, T20, T25 Square: #1, #2 Hex Metric: 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, 6.0mm 28301 - SlimLine Blade Holder 1000Volt 28390 15 Piece Insulated SlimLine Blade Set High quality CV steel, through hardened. Cushion grip. Friction hold blade holder, holds blades securely. Up to 33% narrower insulation diameter then standard insulated tools. In roll up pouch Item No. Slotted: 3.0, 4.0, 5.5, 6.5 Phillips: #1, #2 28390 Xeno SL/PH: #1, #2 lbs. : T8, T10, T15, T20 .56 Square: #1, #2 28301 - SlimLine Blade Holder 28398 19 Piece Insulated SlimLine Blade Set High quality CV steel, through hardened. Cushion grip. Friction hold blade holder, holds blades securely. In zipper case Item No. Slotted: 3.0, 4.0, 5.5mm 28398 Phillips: #1, #2 lbs. Xeno SL/PH: #1, #2 .64 Xeno SL/PZ: #1, 2 : T8, T10, T15, T20 Square: #1, 2 Hex Metric: 3.0, 4.0, 5.0mm 28301 - SlimLine Blade Holder 1000Volt 28304 SlimLine Blade Holder, With Wiha-SoftFinish(R) Handle. Insulation According to VDE, ASTM, EN/IEC, NFPA70E & CSA, up to 1000 Volt. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Size mm Inch lbs. pkg. 1/4" 114 4.5 .21 1 28304 1000Volt 28302 SlimLine Stubby Blade Holder, With Wiha-SoftFinish(R) Handle. Insulation According to VDE, ASTM, EN/IEC, NFPA70E & CSA, up to 1000 Volt. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Size mm Inch lbs. pkg. 1/4" 57 2.2 .11 1 28302 www.wihatools.com 19 Wiha Insulated SlimLine Blades Wiha SlimTECHNOLOGY Integrated Slim Insulation molded directly onto blade High quality CV steel, throughhardened Achieves blade diameters up to 33% narrower utilizing integrated insulation Insulation does not exceed screw head diameter Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, VDE 0682/part 201, DIN 7437, NFPA70E & CSA specification 1000 Volt Rated 10,000 Volt Tested 283 Insulated Slotted SlimLine Blades SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Insulated Xeno Slotted/Pozidriv(R) 283 SlimLine Blades Up to 33% narrower insulation diameter then standard insulated tools. 283 Insulated Square SlimLine Blades Up to 33% narrower insulation diameter then standard insulated tools. Item No. mm Inch 28307 2.5 3/32 28308 3.0 1/8 28310 3.5 9/64 28309 4.0 5/32 28312 5.5 7/32 28315 6.5 1/4 Item No. Size 28320 1 28321 2 Item No. Size 1 28346 2 28347 Slim Dia. 4.0 4.0 4.0 4.0 6.0 6.0 Max Nm 0.4 0.6 2.5 2.5 3.8 5.5 Inch/ lbs. lbs. Pkg. 3.5 .02 1 5.3 .02 1 22.1 .02 1 22.1 .02 1 33.6 .02 1 48.6 .02 1 Slim Dia. 4.0 6.0 Max Nm 3.8 5.5 Inch/ lbs. lbs. Pkg. 33.6 .02 1 48.7 .02 1 Slim Dia. 4.0 6.0 Max Nm 3.8 5.5 Inch/ lbs. lbs. Pkg. 33.6 .02 1 48.7 .02 1 Insulated Phillips SlimLine Blades 283 SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Item Slim Max Inch/ No. Size Dia. Nm lbs. lbs. Pkg. 1 4.0 3.8 33.7 .02 1 28317 2 6.0 5.5 48.8 .02 1 28319 283 Insulated Xeno Slotted/Phillips SlimLine Blades Up to 33% narrower insulation diameter then standard insulated tools. Insulated Hex Metric SlimLine 283 Blades Up to 33% narrower insulation diameter then standard insulated tools. Item No. Size 28327 1 28329 2 Item No. Size 1.5 28332 2.0 28333 2.5 28334 3.0 28335 4.0 28336 5.0 28337 6.0 28338 283 Insulated Pozidriv(R) SlimLine Blades SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. SlimLine Blades 283 Insulated Up to 33% narrower insulation diameter then standard insulated tools. Item No. Size 28330 1 28331 2 Item No. Size 28339 T8 28344 T9 28340 T10 28341 T15 28342 T20 28343 T25 Slim Dia. 4.0 6.0 Max Nm 3.8 5.5 Inch/ lbs. lbs. Pkg. 33.7 .02 1 48.8 .02 1 Slim Dia. 4.0 6.0 Slim Dia. 4.0 4.0 4.0 6.0 6.0 6.0 Max Nm 3.8 5.5 Max Nm 1.3 1.3 3.8 5.5 5.5 5.5 Inch/ lbs. lbs. Pkg. 33.6 .02 1 48.7 .02 1 Inch/ lbs. 11.5 11.5 33.6 48.7 48.7 48.7 lbs. Pkg. .02 1 .02 1 .02 1 .02 1 .02 1 .02 1 Slim Dia. 4.0 4.0 4.0 4.0 6.0 6.0 6.0 Max Nm 0.9 1.8 3.8 5.5 5.5 5.5 5.5 Inch/ lbs. 7.9 15.9 33.6 48.7 48.7 48.7 48.7 lbs. Pkg. .02 1 .02 1 .02 1 .02 1 .02 1 .02 1 .02 1 Toll Free: (800) 494-6104 20 Insulated PicoFinish Precision Screwdrivers Wiha Insulated SlimLine Screwdrivers Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, VDE 0682/part 201, DIN 7437, NFPA70E & CSA specification 1000Volt 320 Insulated Slotted PicoFinish Screwdrivers. Individually Tested Protective Insulation 1000Volt AC, VDE & GS Tested. Item No. mm Inch mm mm lbs. pkg. 1 1.5 .06 40 154 .05 32000 1 2.0 .08 40 154 .07 32001 1 2.5 .10 60 160 .07 32002 1 3.0 .12 60 160 .08 32003 1 3.5 .14 60 160 .08 32004 Integrated Slim Insulation molded directly onto blade Ideal for jobs where access is limited 1000 Volt Rated 10,000 Volt Tested Wiha SlimTECHNOLOGY Achieves blade diameters up to 33% narrower utilizing integrated insulation 1.4" 1000Volt 321 Insulated Phillips PicoFinish Screwdrivers. Individually Tested Protective Insulation 1000Volt AC, VDE & GS Tested. Item No. 32106 32107 32108 Size mm mm lbs. pkg. 1 00 40 154 .05 1 0 60 160 .07 1 1 60 160 .08 1000Volt 32088 8 Piece Slotted & Phillips PicoFinish Set High quality CV steel, through hardened, black finish Item No. Slotted: 1.5, 2.0, 2.5, 3.0, 3.5 lbs. Phillips: #00, #0, #1 .35 32088 Individually Tested Protective Insulation 1000Volt AC, VDE & GS Tested Rotating cap for precise turning and control with fingertip 32085 5 Piece Slotted & Phillips PicoFinish Set High quality CV steel, through hardened, black finish Item No.Slotted: 1.5, 2.5, 3.5 lbs. 32085 Phillips: #0, #1 .26 1000Volt Insulated Slotted SlimLine 320 Screwdrivers Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. mm Inch 3.5 9/64 32046 4.0 5/32 32049 4.5 3/16 32052 5.5 7/32 32055 6.5 1/4 32058 Slim Dia. mm 3.5 100 4.0 100 4.5 125 5.5 125 6.5 150 mm 204 211 211 243 268 lbs. Pkg. .07 1 .12 1 .14 1 .21 1 .25 1 1.4" 1000Volt Insulated Xeno SlimLine Drivers 307 For Terminal Screws Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. Item No. Size 30746 1 30747 2 Slim Dia. mm 4.5 80 6.0 100 mm 191 218 lbs. Pkg. .12 1 .21 1 1.4" 1000Volt Insulated Square SlimLine Drivers 358 Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/ IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. Item Slim No. Size Dia. mm mm lbs. Pkg. 1 4.0 100 218 .12 1 35844 2 4.5 125 243 35845 .19 1 1.4" 1000Volt 1.4" 1000Volt 321 Insulated Phillips SlimLine Screwdrivers Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. Item Slim No. Size Dia. mm mm lbs. Pkg. 32145 1 4.5 80 204 .12 1 32146 2 6.0 100 211 .21 1 325 Insulated Security SlimLine Drivers Insulation According to ASTM, New VDE Specification 0682/part 201 and EN/ IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. Item No. Size mm mm lbs. Pkg. 1 T10s 100 204 .08 32512 1 T15s 100 211 .12 32513 1 T20s 100 211 .12 32514 1 T25s 125 243 .18 32515 .21 1 T27s 125 243 32517 1 T30s 125 243 .21 32518 .26 1 T40s 150 268 32519 www.wihatools.com 21 Wiha Insulated SlimLine Screwdriver Sets 1000Volt 1000Volt Slotted/Phillips 30770 1000Volt 32198 11 Piece Insulated SlimLine Slotted, Phillips, Xeno & Square Screwdrivers. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Slotted: 3.5, 4.0, 4.5, 5.5, 6.5mm Phillips: #1, 2 32198 Square: #1, 2 lbs. 1.75 Xeno: #1, 2 32196 6 Piece Insulated SlimLine Slotted, Phillips & Square Screwdrivers. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Wiha-SoftFinish(R) handle, multicomponent, cushion grip. Item Slotted: 4.5, 6.5mm No.Phillips: #1, #2 lbs. 32196 Square: #1, #2 1.15 1000Volt 1000Volt 32197 8 Piece Insulated SlimLine Slotted, Phillips & Square Screwdrivers. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/ IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Wiha-SoftFinish(R) handle, multicomponent, cushion grip. Item No. Slotted: 3.5, 4.0, 4.5, 5.5mm Phillips: #1, 2 32197 Square: #1, 2 lbs. 1.18 32596 6 Pc. Insulated SlimLine Security Screwdrivers. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Item No. Security : T10s, T15s, T20s, T25s, T27s, T30s 32596 lbs. 1.18 Wiha Slim TECHNOLOGY Achieves blade diameters up to 33% narrower utilizing Wiha integrated insulation 2 Pc. Insulated SlimLine Terminal Block Xeno Slotted/Phillips Screwdrivers. Meets ASTM, VDE, EN/IEC, NFPA70E & CSA Specs, Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Item No. Xeno: #1x80mm 30770 Xeno: #2x100mm lbs. .34 1000Volt 32189 2 Pc. Insulated SlimLine Slotted & Phillips Screwdrivers. Meets ASTM, VDE, EN/IEC, NFPA70E & CSA Specs, Individually Tested to 10,000Volts. High quality CV steel, through hardened. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. Item No. Slotted: 4.5x125mm Phillips: #2x100mm 32189 lbs. .37 1000Volt 32079 30 Pc. Insulated SlimLine Slotted & Phillips Screwdriver Display. Meets ASTM, VDE, EN/IEC, NFPA70E & CSA Specs, Tested to 10,000Volts. SlimLine blades have up to 33% narrower insulation diameter then standard insulated tools. High quality CV steel, through hardened. Item 6 of each: No. Slotted: 3.5, 4.5, 5.5mm 32079 Phillips: #1, #2 Toll Free: (800) 494-6104 22 Wiha Insulated Screwdrivers with SoftFinish(R) Cushion Grip Handle Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, New VDE 0682/part 201, DIN 7437, NFPA70E & CSA Each tool individually tested to 10,000 Volts & certified to 1000 Volt ac or 1500 Volt dc SoftFinish (R) handle Solid molded core with soft outer cushion grip. 40% more torque than #32892 conventional handles Responds to OSHA's use specification 29 CFR1910 Insulation Molded directly onto the blade for permanent bonding Blade CVM tool steel, hardened to average 58/60RC 1000V page 32 1000Volt 320 Slotted Screwdriver, With Wiha-SoftFinish(R) Handle. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested. Item No. mm Inch Inch mm Inch mm Inch lbs. pkg. 2.0 .078 5/64 60 3.0 164 6.5 .05 10 32005 2.5 .098 3/32 75 3.0 179 7.1 .06 10 32010 3.0 .118 1/8 100 4.0 204 8.0 .07 10 32012 3.5 .139 9/64 100 4.0 204 8.0 .07 10 32015 4.0 .157 5/32 100 4.0 211 8.3 .12 10 32017 4.5 .177 3/16 100 4.0 211 8.3 .12 10 32023 4.5 .177 3/16 125 5.0 236 9.3 .12 10 32024 4.5 .177 3/16 150 6.0 261 10.2 .14 10 32027 4.5 .177 3/16 175 7.0 286 11.2 .13 10 32025 4.5 .177 3/16 200 8.0 311 12.3 .15 10 32028 5.5 .216 7/32 125 5.0 243 9.5 .15 10 32031 5.5 .216 7/32 175 7.0 293 11.5 .21 10 32026 6.0 .236 15/64 150 6.0 268 10.6 .21 10 32034 6.5 .255 1/4 150 6.0 268 10.6 .21 10 32039 8.0 .315 5/16 175 7.0 299 11.8 .34 10 32042 10.0 .393 3/8 200 8.0 318 12.5 .39 10 32045 1000Volt 321 Phillips Screwdriver, With Wiha-SoftFinish(R) Handle. Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested. Item No. Size mm Inch mm Inch lbs. pkg. 32100 0 60 2.4 164 6.5 .06 10 32101 1 80 3.0 191 7.5 .12 10 32102 2 100 4.0 218 8.6 .20 10 32103 3 150 6.0 268 10.6 .34 10 32104 4 200 8.0 318 12.5 .39 10 1000Volt 32105 2 Piece Slotted & Phillips Set Item Slotted: 5.5 No. Phillips: #2 32105 lbs. .50 1000Volt 2 Piece Slotted & Phillips Set 33532 Item Slotted: 6.0 No. Phillips: #2 lbs. .50 33532 1000Volt 32090 Item No. 32090 4 Piece Slotted & Phillips Set Slotted: 3.5, 4.5 Phillips: #1, 2 lbs. .76 www.wihatools.com 23 Wiha Insulated Screwdriver Sets 1000Volt 1000Volt 1000Volt 32092 Item No. 32092 6 Piece Slotted & Phillips Set Slotted: 3.5, 4.5, 6.5 Phillips: #1, 2, 3 lbs. 1.38 32094 Item No. 32094 13 Piece Slotted & Phillips Set Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 5.5, 6.5, 8.0, 10.0mm Phillips: #0, 1, 2, 3 lbs. 2.3 1000Volt 1000Volt 32192 14 Piece Slot/Phil/Inch Nut Drivers & Pliers/Cutters Set Item No. Slotted: 3.0, 4.5, 6.5mm Phillips: 1, 2 32192 Nut Drivers Inch: 1/4, 5/16, lbs. 11/32, 3/8, 1/2" 5.5 8.0" Combo Pliers, 6.3" Diagonal Cutters 6.3 & 8.0" Long Nose Pliers/Cutters 1000Volt 32091 Item No. 32091 5 Piece Slotted & Phillips Set Slotted: 3.0, 4.5, 6.5 Phillips: #1, 2 lbs. 1.31 32093 Item No. 32093 10 Piece Slotted & Phillips Set Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 6.5 Phillips: #0, 1, 2, 3 lbs. 1.63 32190 15 Piece Slotted, Phillips & Inch Nut Drivers Set Item No. Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 6.5, 8.0mm 32190 Phillips: #1, 2, 3 lbs. Nut Drivers Inch: 1/4, 5/16, 5.9 3/8, 7/16, 1/2" Tool box set in blow molded tray 1000Volt 32188 7 Piece Slotted & Phillips Set Item No. 32188 Slotted: 2.0, 2.5, 3.0, 3.5, 4.0 Phillips: #0, 1 lbs. .92 1000Volt 32095 19 Piece Slotted, Phillips, Square, Xeno Screwdriver Set Insulated Screwdriver set in a light weight tool box tray. Item No. Slotted: 2.5, 3.0, 3.5, 4.0, 4.5, 32095 5.5, 6.0, 6.5, 8.0, 10.0mm Phillips: #0, #1, #2, #3 Square: #1, #2 lbs. Xeno Terminal: #1, #2 4.92 Cat. III Voltage Detector (Battery Operated) Toll Free: (800) 494-6104 24 Wiha Insulated Hex Metric Screwdrivers 1000Volt 1000Volt 323 Hex Metric Screwdriver, With Wiha-SoftFinish(R) Handle Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested Blade high alloy CVM steel, hardened, black finish. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. Size mm Inch mm Inch lbs. pkg. 2.5 75 3.0 179 7.0 .06 10 32302 3.0 75 3.0 179 7.0 .08 10 32303 4.0 75 3.0 186 7.3 .12 10 32304 5.0 75 3.0 186 7.3 .15 10 32305 6.0 100 3.9 218 8.6 .24 10 32306 8.0 100 3.9 218 8.6 .34 10 32308 Wiha Insulated 32366 6 Piece Insulated Hex Metric Screwdriver Set Item No. 32366 Hex Metric: 2.5, 3.0, 4.0, 5.0, 6.0, 8.0mm lbs. 1.06 Screwdrivers 1000Volt 325 Screwdriver, With Wiha-SoftFinish(R) Handle Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Blade high alloy cvm steel, hardened, black finish. Insulation molded directly onto blade. Item No. Size mm Inch mm Inch lbs. pkg. 32505 T5 60 2.4 164 6.5 .06 10 32511 T6 60 2.4 164 6.5 .06 10 32516 T7 60 2.4 164 6.5 .06 10 32521 T8 60 2.4 164 6.5 .06 10 32526 T9 60 2.4 164 6.5 .06 10 32531 T10 60 2.4 164 6.5 .06 10 32536 T15 80 3.0 191 7.5 .12 10 32541 T20 80 3.0 191 7.5 .12 10 32546 T25 80 3.0 198 7.8 .17 10 32551 T27 100 4.0 218 8.6 .20 10 32556 T30 100 4.0 218 8.6 .20 10 32561 T40 150 6.0 274 10.8 .30 10 32566 T45 150 6.0 274 10.8 .35 10 1000Volt 32590 Item No. 32590 6 Piece Set TORX: T8, T9, T10, T15, T20, T25 lbs. .83 1000Volt 32592 Item No. 32592 10 Piece Set TORX: T6, T7, T8, T9, T10, T15, T20, T25, T27, T30 lbs. 1.2 Wiha Insulated Square Tip Screwdrivers 1000Volt 358 Square Tip Screwdriver, With Wiha-SoftFinish(R) Handle Insulation According to ASTM, VDE, EN/IEC, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Blade high alloy CVM steel, hardened, black finish. Item No. Size mm Inch mm Inch lbs. pkg. 35811 1 100 4.0 210 8.2 .12 10 35812 2 150 6.0 268 10.5 .19 10 1000Volt 1000Volt 6 Pc. Insulated Slotted, Phillips 35891 & Square Screwdrivers Item No. Slotted: 3.0, 5.5mm 35891 Phillips: #1, 2 lbs. Square: #1, 2 .83 35890 6 Pc. Insulated Slotted, Phillips & Square Screwdrivers Item No. Slotted: 4.5, 6.5mm 35890 Phillips: #1, 2 lbs. Square: #1, 2 .83 www.wihatools.com 25 Wiha Insulated Pozidriv(R) Screwdrivers Wiha Insulated Screwdrivers 1000Volt 1000Volt 324 Pozidriv(R) Screwdriver, With Wiha SoftFinish(R) Handle. Insulation According to ASTM F-1505, VDE, 0682/part 201, EN/IEC 60900, NFPA70E & CSA specification. Individually Tested. Item No. Size mm mm Inch lbs. pkg. 32400 0 60 164 6.5 .11 10 32401 1 80 191 7.5 .13 10 32402 2 100 218 8.6 .23 10 32403 3 150 267 10.5 .30 5 Insulated Terminal Block Xeno Screwdrivers Combination Slotted/Phillips Terminal Block Drivers Slotted/Phillips or Slotted/Pozidriv(R) 1000Volt Slotted/Phillips Slotted/Pozidriv(R) Combination Terminal Block Xeno 307 Screwdriver, With Wiha SoftFinish(R) Handle. Insulation According to ASTM F-1505, VDE, 0682/part 201, EN/IEC 60900, NFPA70E & CSA specification. Individually Tested. Blade CVM steel, hardened, black finish. Insulation molded directly onto blade. WihaSoftFinish(R) handle, multi-component, cushion grip. For combination Slotted/Phillips head terminal screws. Item No. Size mm mm Inch lbs. pkg. 30700 .13 10 1 80 191 7.5 30701 .23 10 2 100 218 8.6 Combination Terminal Block Xeno 307 Screwdriver, With Wiha SoftFinish(R) Handle. Insulation According to ASTM F-1505, VDE, 0682/part 201, EN/IEC 60900, NFPA70E & CSA specification. Individually Tested. Blade CVM steel, hardened, black finish. Insulation molded directly onto blade. WihaSoftFinish(R) handle, multi-component, cushion grip. For combination Slotted/Pozidriv(R) head terminal screws. Item No. Size mm mm Inch lbs. pkg. 1 80 191 7.5 .12 10 30711 2 100 218 8.6 .21 10 30712 Cat. III Voltage Detector Battery Operated Insulated Single-Pole Voltage Detector 1000Volt 25500 Battery Operated Voltage Detector Tests 90-1000 Volts. Category III, CE IEC 61010-1 With audible sound and light warnings. Requires 2 AAA batteries. Item No. mm Inch lbs. pkg. 150 6.0 .13 1 25500 Workstation Insulated screwdrivers in a steel stand 32199 30 Pc. Workstation Insulated Screwdriver Set Item No. Slotted: 3.5, 4.0, 4.5, 5.5, 6.5mm 32199 Phillips: #1, #2, #3 Pozidriv(R): #1, #2 lbs. Square: #1, #2 8.50 Xeno Terminal Slt/Ph: #1, #2 Hex Metric: 2.5, 3.0, 4.0, 5.0, 6.0mm TORX(R): T8, T10, T15, T20, T25, T30 PicoFinish Slotted: 1.5, 2.0, 2.5mm PicoFinish Phillips: #00, #0 Insulated Drivers & Voltage Detector Sets 1000Volt 32089 9 Pc. Slotted, Phillips, Square & Voltage Detector Set In Molded Carry Case Item Slotted: 3.5, 4.0, 4.5, 5.5mm No. Phillips: #1, #2 Xeno Slt/Ph: #2 32089 Ins. Single Pole Voltage Detector lbs. 1.81 1000Volt 1000Volt 25511 Insulated Single-Pole Voltage Detector. 110-250Volts. Insulation According To DIN 57860/6 And DIN VDE 0680-6, GS Tested. Blade CVM steel, hardened, nickelplated. Insulation molded directly onto blade. Amber LED light. 10,000Volt tested. Item No. mm mm mm Inch lbs. pkg. 3.0 65 145 5.7 .04 1 25511 32087 7 Pc. Slotted, Phillips, Square & Voltage Detector Set Item Slotted: 4.0, 5.5, 6.5mm No. Phillips: #1, #2 Square: #2 32087 Ins. Single Pole Voltage Detector lbs. 1.36 Toll Free: (800) 494-6104 26 Wiha Insulated Metric & Inch Nut Drivers 1000Volt 1000Volt 322 Metric Nut Drivers, With Wiha-SoftFinish(R) Handle Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested. Blade CVM steel, hardened. Insulation molded directly onto blade. Deep drawn 1" socket. Wiha-SoftFinish(R) handle, multi-component. Item No. mm mm mm Inch lbs. pkg. 32206 4.0 125 236 9.3 .15 10 32209 5.0 125 236 9.3 .16 10 32212 5.5 125 236 9.3 .16 10 32215 6.0 125 236 9.3 .16 10 32218 7.0 125 243 9.6 .25 10 32221 8.0 125 243 9.6 .25 10 32224 9.0 125 243 9.6 .25 10 32227 10.0 125 243 9.6 .27 10 32230 11.0 125 243 9.6 .37 10 32233 12.0 125 243 9.6 .38 10 32236 13.0 125 243 9.6 .39 10 32238 14.0 125 243 9.6 .39 10 32239 15.0 125 243 9.6 .40 10 32240 16.0 125 243 9.6 .42 10 32241 17.0 125 243 9.6 .44 10 322 Item No. 32255 32258 32261 32264 32267 32268 32270 32273 32276 32278 32280 32291 5 Pc. Nut Driver Set - Metric Sizes Item Metric: No. 6.0, 7.0, 8.0, 9.0, 10.0mm lbs. 32291 1.36 1000Volt 32293 Item No. 32293 7 Pc. Nut Driver Set - Metric Sizes Metric: 5.0, 5.5, 6.0, 7.0, lbs. 8.0, 10.0, 13.0mm 2.05 Inch Nut Drivers, With Wiha-SoftFinish(R) Handle Inch 5/32 3/16 7/32 1/4 5/16 11/32 3/8 7/16 1/2 9/16 5/8 Inch 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 mm 236 236 236 243 243 242 243 243 243 243 243 Inch 9.3 9.3 9.3 9.6 9.6 9.6 9.6 9.6 9.6 9.6 9.6 lbs. .15 .15 .16 .24 .25 .26 .26 .36 .39 .39 .41 pkg. 10 10 10 10 10 10 10 10 10 10 10 1000Volt 32292 Item No. 32292 5 Pc. Nut Driver Set - Inch Sizes Inch: 7/32, 1/4, 5/16, lbs. 3/8, 1/2" 1.52 1000Volt In roll-up pouch 1000Volt 32296 11 Pc. Nut Driver Set - Inch Sizes Item Inch: 5/32, 3/16, 7/32, 1/4, No. 5/16, 11/32, 3/8, 7/16, lbs. 32296 1/2, 9/16, 5/8" 3.00 1000Volt 32288 9 Pc. Nut Driver Set - Inch Sizes ItemInch: 3/16, 1/4, No. 5/16, 11/32, 3/8, lbs. 7/16, 1/2, 9/16, 5/8" 3.16 32288 32294 Item No. 32294 7 Pc. Nut Driver Set - Inch Sizes Inch: 3/16, 7/32, 1/4, 5/16, lbs. 3/8, 7/16, 1/2" 2.24 www.wihatools.com 27 Multi-Bit Screwdrivers "Six Tools In One" Tested to 10,000 Volts Insulated Bit Holder Wiha Insulated Pop-Up Insert Bit Sets Certified to VDE, EN ISO, BS EN, ASME specifications Convenient rotating cap Insulation meets EN/IEC 60900 Multi-Bit Screwdriver Sets with Wiha Powerhandle, cellulose-acetate, impact resistant. Snap-lock rotatable cap. Chambered bit holder equipped with transparent selector & 6 bits. 1/4" Bit holder, stainless steel. Shaft CVM steel, hardened, chrome-plated. Packaged in clear blister package. Blade Length = 120mm (4.7") Overall Length = 230mm (9") 38006 Insulated Slotted/Phillips MultiBit Screwdriver Set includes the following 1/4" bits: Slotted: 5.5, 6.0mm Phillips: #0, 1, 2, 3 lbs. .39 1000Volt 38007 Insulated Slotted/Phillips/Square Multi-Bit Screwdriver Set includes the following 1/4" bits: Slotted: 6.5, 8.0mm Phillips: #1, 2 Square: #1, 2 lbs. .41 1000Volt Blades High quality CV steel, through-hardened Friction hold bit holder securely holds bits in place 1000Volt Rated 10,000 Volt Tested 1000Volt Insulated Pop-Up Bit Holder Set 38050 With 1/4" Insert Bits Insulated cushion grip multi-component handle. Bit holder holds 1/4" Insert bits. Convenient rotating cap. Item Set includes the following bits: No. Slotted: 4.5, 5.5, 6.0mm 38050 Phillips: #0, 1, 2, 3 Square: #1, 2, 3 Pozidriv(R): #1, 2, 3 lbs. .46 1000Volt 38051 Insulated Pop-Up Bit Holder Set With 1/4" Insert Bits Insulated cushion grip multi-component handle. Bit holder holds 1/4" Insert bits. Convenient rotating cap. Item Set includes the following bits: No. Slotted: 4.5, 5.5, 6.0mm 38051 Phillips: #0, 1, 2, 3 Square: #1, 2, 3 : T15, T20, T25 lbs. .46 Tested to 10,000 Volts Magnetic Bit Holder, 1/4" Wiha 38025 Powerhandle & insulated shaft. Holds up to 6 bits. (Holder only) lbs. .26 WARNING! Insulated Tools are intended to provide protection against accidental contact with charged energized circuits. For maximum safety we recommend de-energizing all circuits whenever possible before starting work on electrical apparatus or conductors. Always visually inspect insulation on tools before use, do not use tools if insulation shows signs of wear or damage to the insulated areas of the tool. Wear appropriate eye protection when using hand tools. Use NFPA70E certified insulated protective outer wear when appropriate. Use & Care Guide For Insulated Tools: Store tools to minimize risk of damage to insulation, always wear approved eye protection, Inspect insulation prior to each use of any insulated tool. Use insulated tools where the ambient temperature is between -20 to +70O C. Have a qualified safety technician visually inspect insulation on tools annually for safe use. Toll Free: (800) 494-6104 28 Wiha Insulated Belt Pack Pouch Sets 1000Volt Insulated Industrial Pliers & Cutters 1000Volt 32990 17 Pc. Insulated Pop-Up Bit Holder & Industrial Pliers/ Cutters Set High quality CV steel, through hardened. Cushion grip handle with magnetic holder to securely hold bits. Pliers & Cutters drop-forged from special tool steel. Industrial Soft grip ergonomically designed handle body. In belt pack pouch 32871 3 Piece Insulated Pliers/Cutters & Multi-Bit Set In Belt Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA standards. Pliers chrome finish for long lasting corrosion protection. Soft grip ergo designed handle body, safety slip guard. Insulated multi-bit screwdriver includes Slotted, Phillips & Square bits. Item No. 32990 Item No. 32871 lbs. 3.60 Set Includes 1/4" Insert Bits: Slotted: 4.5, 5.5, 6.0mm * Phillips: #0, 1, 2, 3 Square: #1, 2, 3 * : T15, T20, T25 8.0"/200mm Long Nose Pliers 8.0"/200mm High Leverage Cutters 9.5"/245mm Lineman's Pliers Pliers/Cutters & Multi-Bit Set 6.3" / 160mm Diagonal Cutters 8.0" / 200mm Long Nose Pliers Set Includes Bit Holder & The Following Bits: Slotted: 4.5, 6.5mm * Phillips: 1, 2 * Square: 1, 2 lbs. 1.67 1000Volt 1000Volt Chrome Finish Pliers & Cutters 17 Pc. Insulated Pop-Up Bit Holder & Pliers/Cutters Set 32886 High quality CV steel, through hardened. Cushion grip handle with magnetic holder to securely hold bits. Pliers & Cutters additionally induction hardened. Hard chrome finish for long lasting corrosion protection. Two component Insulated soft grip handle. In belt pack pouch Item No. 32886 lbs. 3.72 Set Includes 1/4" Insert Bits: Slotted: 4.5, 5.5, 6.0mm * Phillips: #0, 1, 2, 3 Square: #1, 2, 3 * : T15, T20, T25 8.0"/200mm Long Nose Pliers 8.0"/200mm High Leverage Cutters 9.5"/245mm Lineman's Pliers 5 Pc. Insulated Pliers/Cutters & SlimLine Screwdrivers 32875 In Belt Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA standards. Pliers chrome finish for long lasting corrosion protection. Soft grip ergo designed handle body, safety slip guard. Insulated cushion grip drivers, multi-component. Blade CVM tool steel, hardened. Item No. Insulated Pliers/Cutters & Screwdrivers 32875 9.0" / 225mm Lineman's Pliers 8.0" / 200mm Long Nose Pliers Insulated SlimLine SoftFinish(R) Screwdrivers: Slotted: 4.5, 6.5mm * Phillips: 2 lbs. 2.26 1000Volt 1000Volt 32873 3 Piece Insulated Pliers/Cutters In Belt Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA standards. Pliers chrome finish for long lasting corrosion protection. Soft grip ergo designed handle body, safety slip guard. Item No. 32873 Insulated Pliers & Cutters 6.3" / 160mm Diagonal Cutters 8.0" / 200mm Long Nose Pliers 8.0" / 200mm Combination Pliers lbs. 2.12 5 Piece Insulated Pliers/Cutters & Screwdrivers In Belt 32872 Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA standards. Pliers chrome finish for long lasting corrosion protection. Soft grip ergo designed handle body, safety slip guard. Insulated cushion grip drivers, multi-component. Blade CVM tool steel, hardened. Item No. Insulated Pliers/Cutters & Screwdrivers 6.3" / 160mm Diagonal Cutters 32872 8.0" / 200mm Long Nose Pliers Insulated SoftFinish(R) Screwdrivers: Slotted: 3.0, 4.5mm * Phillips: 2 lbs. 1.77 www.wihatools.com 29 Wiha Insulated Master Electrician's Tools Wiha Insulated Master Electrician's Tools Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, New VDE 0682/part 201, DIN 7437, NFPA70E & CSA Insulation Test Standards: Insulation according to EN/IEC 60900, ASTM F-1505, New VDE 0682/part 201, DIN 7437, NFPA70E & CSA All Tools In Dedicated Positions For Quick Storage & Easy Location Tracking 1000Volt Inch 1000Volt Metric All Tools In Dedicated Positions For Quick Storage & Easy Location Tracking 32800 80 PC. Insulated Master Electrician's Tool Set In Rolling Water Tight Traveling Tool Box - 10,000Volt Tested, 1000Volt Rated 32801 112 Pc. Insulated Master Electrician's Tool Set In Rolling Water Tight Traveling Tool Box - 10,000Volt Tested, 1000Volt Rated Item# 32800 Set Includes: 6.3" Long Nose Pliers 8.0" Long Nose Pliers 6.3" Bent Nose Pliers 6.3" Long Flat Nose Pliers 9.0" Combo Pliers/Crimpers Insulated Inch Sockets: 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8" Insulated Metric Sockets: 13.0, 14.0, 15.0, 17.0, 19.0, 20.0, 22.0mm Insulated Ratchet 3/8" Drive Insulated 4.9" Extension 3/8" Dr. Insulated Inch Nut Drivers: 7/32, 1/4, 5/16, 3/8, 7/16" Insulated Metric Nut Drivers: 5.0, 5.5, 6.0, 7.0, 8.0, 10.0, 13.0mm Insulated T-handle Inch Hex: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8" Insulated T-handle Metric Hex: 4.0, 5.0, 6.0, 8.0mm Item# 32801 Set Includes: 6.3" Long Nose Pliers 8.0" Long Nose Pliers 6.3" Bent Nose Pliers 6.3" Long Flat Nose Pliers 9.0" Combo Pliers/Crimpers Insulated Inch Sockets: 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8" Insulated Metric Sockets: 13.0, 14.0, 15.0, 17.0, 19.0, 20.0, 22.0mm Insulated Ratchet 3/8" Drive Insulated 4.9" Extension 3/8" Dr. Insulated Inch Nut Drivers: 7/32, 1/4, 5/16, 3/8, 7/16" Insulated Metric Nut Drivers: 5.0, 5.5, 6.0, 7.0, 8.0, 10.0, 13.0mm Insulated L-key: 10mm Insulated L-key: 1/2" Insulated Cable Knife: 50mm Cat. III Voltage DetectorBattery Operated lbs. 33.9 6.3" Diagonal Cutters 8.0" High Leverage Cutters 6.3" Cable Cutters 6.3" Stripping Pliers 8.0" Adjustable Wrench Insulated Slotted: 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm Insulated Phillips: #0, 1, 2, 3 Insulated Xeno Slotted/Phillips Terminal: #1, 2 Insulated Square: #1, 2 Insulated TORX: T6, T7, T8, T9, T10, T15, T20, T25, T30 Insulated L-key: 10mm Insulated L-key: 1/2" Insulated Cable Knife: 50mm Insulated Folding Ruler In/MM Cat. III Voltage DetectorBattery Operated Use & Care Guide For Insulated Tools: Store tools to minimize risk of damage to insulation, always wear approved eye protection, Inspect insulation prior to each use of any insulated tool. Use insulated tools where the ambient temperature is between -20 to +70O C. Have a qualified safety technician visually inspect insulation on tools annually for safe use. Insulated Folding Ruler In/MM lbs. 51.3 6.3" Diagonal Cutters 8.0" High Leverage Cutters 6.3" Cable Cutters 6.3" Stripping Pliers 8.0" Adjustable Wrench Insulated Slotted: 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm Insulated Phillips: #0, 1, 2, 3 Insulated Xeno Slotted/Phillips Terminal: #1, 2 Insulated Square: #1, 2 Insulated TORX: T6, T7, T8, T9, T10, T15, T20, T25, T30 Insulated T-handle Inch Hex: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8" Insulated T-handle Metric Hex: 4.0, 5.0, 6.0, 8.0mm Insulated Inch Deep Offset Ring Wrenches: 1/4, 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 25/32, 13/16, 7/8, 15/16, 1, 1-1/16, 1-1/4" Insulated Metric Deep Offset Ring Wrenches: 8.0, 9.0, 10.0, 11.0, 12.0, 13.0, 14.0, 15.0, 17.0, 19.0, 20.0, 22.0, 24.0, 27.0, 30.0, 32.0mm Toll Free: (800) 494-6104 30 Wiha 1000Volt Insulated Tool Sets - Comfort Grip Handles Master Electrician's Sets 80 Pc. BIGGEST SET 66 Pc. BIGGER SET 1000Volt 1000Volt 32877 80 Piece Insulated Master Electrician's Set Item# 32877 Set Includes: lbs. 27.0 6.3" Long Nose Pliers 6.3" Diagonal Cutters 6.3" Bent Nose Pliers 8.0" BiCut SuperCut 8.0" Long Nose Pliers 8.0" Cable Cutters 6.3" Long Flat Nose Pliers 6.3" Stripping Pliers 9.0" Combo Pliers/Crimpers 8.0" Adjustable Wrench Insulated Nut Driver 7/32" Insulated Slotted 2.0mm Insulated Nut Driver 1/4" Insulated Slotted 2.5mm Insulated Nut Driver 5/16" Insulated Slotted 3.0mm Insulated Nut Driver 3/8" Insulated Slotted 3.5mm Insulated Nut Driver 7/16" Insulated Slotted 4.0mm Insulated Slotted 4.5mm Insulated Nut Driver 5.0mm Insulated Slotted 5.5mm Insulated Nut Driver 5.5mm Insulated Slotted 6.0mm Insulated Nut Driver 6.0mm Insulated Slotted 6.5mm Insulated Nut Driver 7.0mm Insulated Slotted 8.0mm Insulated Nut Driver 8.0mm Insulated Slotted 10.0mm Insulated Nut Driver 10.0mm Insulated Phillips #0 Insulated Nut Driver 13.0mm Insulated Phillips #1 Insulated T-handle Hex 5/32" Insulated Phillips #2 Insulated T-handle Hex 3/16" Insulated Phillips #3 Insulated T-handle Hex 7/32" Insulated Slt/Ph Terminal #1 Insulated T-handle Hex 1/4" Insulated Slt/Ph Terminal #2 Insulated T-handle Hex 5/16" Insulated T-handle Hex 3/8" Insulated Torx T6 Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Torx T7 Torx T8 Torx T9 Torx T10 Torx T15 Torx T20 Torx T25 Torx T30 Square #1 Square #2 Socket 1/2" Socket 9/16" Socket 5/8" Socket 11/16" Socket 3/4" Socket 13/16" Socket 7/8" Insulated Insulated Insulated Insulated T-handle T-handle T-handle T-handle Hex Hex Hex Hex 4.0mm 5.0mm 6.0mm 8.0mm Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated Insulated L-key 10mm L-key 1/2" Cable Knife 50mm Folding Ruler In/MM Ratchet 3/8" Dr. 4.9" Extension Socket 13mm Socket 14mm Socket 15mm Socket 17mm Socket 19mm Socket 20mm Socket 22mm 32876 66 Pc. Master Electrician's Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome/nickel plated, mirror-polished. Item# Set Includes: 32876 8.0" Long Nose 6.3" Long Flat Nose 9.0" Combo Pliers/Crimpers 8.0" Cable Cutters Insulated Nut Driver 1/4" Insulated Nut Driver 5/16" Insulated Nut Driver 11/32" Insulated Nut Driver 3/8" Insulated Nut Driver 7/16" Insulated T-handle Hex 4.0mm Insulated T-handle Hex 5.0mm Insulated T-handle Hex 6.0mm Insulated T-handle Hex 8.0mm Insulated T-handle Hex 5/32" Insulated T-handle Hex 3/16" Insulated T-handle Hex 7/32" Insulated T-handle Hex 1/4" Insulated T-handle Hex 5/16" Insulated T-handle Hex 3/8" Insulated Hex L-key 10.0mm Insulated Hex L-key 1/2" Insulated Socket 1/2" Insulated Socket 9/16" Insulated Socket 5/8" Insulated Socket 11/16" Insulated Socket 3/4" Insulated Socket 13/16" Insulated Socket 7/8" Insulated Socket 8.0mm Insulated Socket 10.0mm Insulated Socket 13.0mm Insulated Socket 14.0mm Insulated Socket 15.0mm lbs. 21.5 6.3" Side Cutters 8.0" BiCut SuperCut 6.3" Stripping Pliers 8.0" Adjustable Wrench Insulated Slotted 2.0mm Insulated Slotted 2.5mm Insulated Slotted 3.0mm Insulated Slotted 4.0mm Insulated Slotted 4.5mm Insulated Slotted 5.5mm Insulated Slotted 6.0mm Insulated Slotted 8.0mm Insulated Slotted 10.0mm Insulated Phillips #0 Insulated Phillips #1 Insulated Phillips #2 Insulated Phillips #3 Insulated Torx T8 Insulated Torx T10 Insulated Torx T15 Insulated Torx T20 Insulated Torx T25 Insulated Torx T30 Insulated Square #1 Insulated Square #2 Insulated Slt/Ph Terminal #1x80 Insulated Slt/Ph Terminal #2x100 Insulated Cable Knife 50mm Insulated Extension 4.9" Insulated Ratchet 3/8" Driver Insulated Socket 17.0mm Insulated Socket 19.0mm Insulated Socket 22.0mm www.wihatools.com 31 Wiha 1000Volt Insulated Tool Sets - Comfort Grip Handles 25 Pc. Set 50 Pc. BIG SET 1000Volt 1000Volt 32874 50 Piece Insulated Tool Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome/nickel plated, mirror-polished. Cushion Grip Insulated handles. Canvas tool bag. 32874 Item# Set Includes: lbs. 19.8 6.3" Long Nose Pliers 6.3" Side Cutters 8.0" Long Nose Pliers 8.0" BiCut SuperCut 6.3" Combination Pliers 6.3" Stripping Pliers 9.0" Combo Pliers/Crimpers 8.0" Adjustable Wrench 10.0" Water Pump Pliers Battery Operated Voltage Detector Slotted: 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0mm Phillips: #0, 1, 2, 3 Square: #1, 2 Slt/Ph Terminal: #1, 2 TORX: T8, T9, T10, T15, T20, T25, T27, T30 Hex Inch: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8" Nut Driver Inch: 7/32, 1/4, 5/16, 3/8, 7/16, 1/2" 50mm Cable Stripping Knife & Insulated Inch/Metric Folding Ruler 32879 25 Pc. Pliers & Screwdriver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome/nickel plated, mirror-polished. In tool box. Item# 32879 Set Includes: lbs. 11.92 8.0" Long Nose 6.3" Stripping Pliers 9.0" Combination Pliers Insulated Inch & Metric Folding Ruler 8.0" BiCut SuperCut 8.5" Insulated Knife Slotted: 3.0, 4.5, 6.0mm Phillips: #1, #2 Square: #1, #2 Terminal Block Driver: #1, #2 Inch Nut Driver: 1/4, 5/16, 11/32, 3/8, 7/16, 1/2" Metric Nut Driver: 7.0, 8.0, 10.0, 13.0mm 1000Volt 13 Pc. Set 31 Pc. Set 1000Volt 32878 13 Piece Pliers & Screwdriver Set. In canvas tool bag Item# 32878 Set Includes: lbs. 5.16 8.0" Long Nose 50mm Cable Stripping Knife 8.0" BiCut SuperCut Insulated Slotted: 3.0mm 9.0" Combo Pliers/Crimpers Insulated Slotted: 4.5mm Insulated Phillips: #1 Insulated Slotted: 6.0mm Insulated Phillips: #2 Insulated Square: #1 Insulated Slt/Ph Terminal: #1 Insulated Square: #2 Insulated Slt/Ph Terminal: #2 32896 31 Pc. Pliers & Screwdriver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome/nickel plated, mirror-polished. Set includes Insulated Inch & Metric folding ruler. Item# 32896 Set Includes: lbs. 12.85 6.3" Long Nose Pliers 6.3" Side Cutters 8.0" Long Nose Pliers 8.0" BiCut SuperCut 7.0" Linemans Pliers 6.3" Stripping Pliers 9.0" Combination Pliers 6.3" Round Nose Pliers Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 5.5, 6.5, 8.0, 10.0mm Phillips: #0, #1, #2, #3 Inch Nut Driver: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16" Toll Free: (800) 494-6104 32 Wiha Insulated Pliers with High Visibility Comfort Grip Handle 1000Volt 1000Volt * Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome and nickel plated, mirror-polished. * In zipper carry case 32891 10 Piece Pliers & Screwdriver Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Item# 32891 Set Includes: lbs. 5.54 8.0" Combination Pliers 8.0" Long Nose 8.0" BiCut SuperCut 6.3" Cable Cutters 6.3" Universal Wire Stripper Insulated Phillips #1 Insulated Slotted 4.5mm Insulated Phillips #2 Insulated Slotted 6.5mm Insulated Phillips #3 * Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome and nickel plated, mirror-polished. * In zipper carry case 1000Volt 32895 14 Piece Pliers & Screwdriver Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Item# 32895 Set Includes: lbs. 6.60 8.0" Long Nose 6.3" Side Cutters 9.0" Combination Pliers 8.0" BiCut SuperCut 6.3" Stripping Pliers Insulated Slotted 2.5mm Insulated Phillips #1 Insulated Slotted 3.0mm Insulated Phillips #2 Insulated Slotted 3.5mm Insulated Phillips #3 Insulated Slotted 4.5mm Insulated Slotted 2.0mm Insulated Slotted 6.5mm 32888 11 Piece Pliers & Screwdriver Set In Canvas Pouch Item# 32888 Set Includes: lbs. 3.58 6.3" Long Nose 6.3" Side Cutters 8.0" Combination Pliers 6.3" Stripping Pliers Insulated Slotted 2.5mm Insulated Phillips #0 Insulated Slotted 3.5mm Insulated Phillips #1 Insulated Slotted 4.5mm Insulated Phillips #2 Insulated Slotted 6.0mm 1000Volt 32892 10 Piece Pliers & Screwdriver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome and nickel plated, mirror-polished. In canvas tool bag Item# 32892 Set Includes: lbs. 6.64 8.0" Bent Nose 8.0" Combination Pliers 6.3" Long Nose 6.3" Side Cutters Insulated Phillips #0 Insulated Slotted 3.0mm Insulated Phillips #1 Insulated Slotted 4.5mm Insulated Phillips #2 Insulated Slotted 6.5mm 1000Volt 13 Piece Pliers & Screwdriver Set In canvas tool bag 32894 Item# 32894 Set Includes: lbs. 9.5 8.0" Bent Nose 8.0" Combination Pliers 6.3" Long Nose 6.3" Side Cutters 10" Water Pump Pliers Insulated Slotted: 4.5 & 6.5mm Insulated Nut Driver: Insulated Phillips: #1 & #2 1/4, 5/16, 3/8, 1/2" www.wihatools.com 33 Wiha Insulated Pliers with High Visibility Comfort Grip Handle * Pliers drop-forged from special tool steel, individually high frequency induction hardened, chrome and nickel plated, mirror-polished. 1000Volt 32889 8 Piece Pliers & Cutters Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Item# 32889 Set Includes: lbs. 4.63 6.3" Long Nose Pliers 8.0" Long Nose Pliers 6.3" Lineman's Pliers 6.3" Diagonal Cutters 9.0" Lineman's Pliers 8.0" BiCut SuperCut 6.3" Wire Stripping Pliers Electrician's Knife 1000Volt 32869 14 Piece Pliers/Cutters & Screwdrivers Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Item# 32869 Set Includes: lbs. 6.52 9.0" Lineman's Pliers 8.0" BiCut SuperCut 8.0" Cable Cutters 8.0" Long Nose Pliers 6.0" Stripping Pliers 10-20 AWG SlimLine Slotted 3.0, 4.5, 6.5mm SlimLine Phillips #1, 2 SlimLine Square #1, 2 SlimLine Terminal #2 Single Pole Tester 1000Volt 1000Volt 32867 10 Piece Pliers & Screwdriver Set In Canvas Pouch Item# 32867 Set Includes: lbs. 4.06 6.3" Diagonal Cutters 9.0" Combo Pliers 6.3" Long Nose Pliers 6.3" Wire Strippers 7.0" Crimping Pliers Insulated Slotted 4.5mm Insulated Phillips #1 Insulated Slotted 6.0mm Insulated Phillips #2 Insulated Square: #2 32868 10 Piece Pliers & Screwdriver Set In Canvas Pouch Item# 32868 Set Includes: lbs. 4.24 7.0" Diagonal Cutters 9.0" Combo Pliers 8.0" Long Nose Pliers 6.3" Wire Strippers 7.0" Crimping Pliers Insulated Slotted 3.0, 4.5, 6.0mm Insulated Phillips #1, 2 1000Volt 32899 7 Pc. Pliers & Driver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. In molded tool box Item# Set Includes: lbs. 5.39 32899 9.0" Linemans Pliers 6.3" Long Nose Pliers W/Cutter 6.3" Diagonal Cutter Insulated Phillips #1, 2 Insulated Slotted 3.0, 4.5mm Toll Free: (800) 494-6104 34 Insulated Pliers/Cutters & Screwdrivers Sets 1000Volt 32856 5 Pc. Insualted Pliers/Cutters & Screwdriver Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Screwdriver blade high alloy CVM steel, hardened, black finish. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. 32856 lbs. 1.81 Insulated Pliers/Cutters 8.0" Long Nose Pliers 6.3" Diagonal Cutters Insulated Slotted & Phillips Drivers Slotted: 4.5, 5.5mm Phillips: #2 1000Volt 1000Volt 32857 7 Pc. Insualted Pliers/Cutters & Screwdriver Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Screwdriver blade high alloy CVM steel, hardened, black finish. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. 32857 lbs. 1.85 Insulated Pliers/Cutters 8.0" BiCut SuperCut Pliers Insulated Slotted & Phillips Drivers Slotted: 3.5, 4.5, 5.5mm Phillips: #0, #1, #2 1000Volt 32865 8 Pc. Insualted Pliers/Cutters & SlimLine Blade Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. SlimLine blades high alloy CV steel, through hardened. Blades have up to 33% narrower insulation diameter then standard insulated tools. 32858 7 Pc. Insualted Pliers/Cutters & Screwdriver Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Screwdriver blade high alloy CVM steel, hardened, black finish. Insulation molded directly onto blade. Wiha-SoftFinish(R) handle, multi-component, cushion grip. Item No. 32865 Item No. 32858 lbs. .98 Insulated Pliers/Cutters 8.0" Long Nose Pliers Insulated Slotted & Phillips SlimLine Blades Slotted: 3.0, 4.0, 5.5, 6.5mm Phillips: #1, #2 lbs. 1.81 Insulated Pliers/Cutters 8.0" Combination Lineman's Pliers Insulated Slotted & Phillips Drivers Slotted: 3.5, 4.5, 5.5mm Phillips: #0, #1, #2 www.wihatools.com 35 NE Style Lineman's Pliers Set Insulated Pliers & Cutters Sets Insulated Tool meets ASTM, IEC, EN, NFPA & CSA standards Individually Tested 1000Volt 32862 2 Pc. Insualted Pliers & Cutters Set Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Item No. Insulated Pliers & Cutters Pliers lbs. 1.66 8.0" BiCut SuperCut Pliers 32862 8.0" Combination Pliers Knurled striking zone on vinyl grip pliers Extra long cutting edge for flat and round cables 1000Volt 32833 Item No. 32833 2 Pc. NE Style Lineman's Pliers Set NE Style Lineman's Pliers 9.5" Insulated & 9.5" Vinyl Soft Grip - Lineman's Pliers lbs. 2.22 1000Volt Insulated BiCut SuperCut 3 Pc. Insualted Pliers/Cutters & Stripping Pliers Set 32863 Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Item No. Insulated Pliers/Cutters & Stripping Pliers 32863 8.0" High Leverage Diagonal Cutters lbs. 9.0" Lineman's Pliers W/Crimpers 2.21 6.3" Stripping Pliers Strips 0.81-2.59 / AWG #20-#10 Cutting capacity up to 3mm hardened piano wire 1000volt 1000Volt 3 Pc. Insualted Pliers & Cutters Set 32864 Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Pliers drop forged of high C70 steel. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Item No. Insulated Pliers & Cutters 32864 6.3" Diagonal Cutters lbs. 8.0" Long Nose Pliers 1.94 8.0" Combination Lineman's Pliers * * * * * Double the power at the press of a button BiCut does the job of two pairs of pliers Up to 50% less hand strength required for cutting Cutting force doubled for extremely hard materials Easily switch between two strengths in one-handed operation 32837 Insulated BiCut SuperCut. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 Volt. Individually Tested. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Drop forged of high C70 steel. For cutting various materials from soft to extremely hard, such as nails, screws, bolts, wire cables, spring wires, chains, etc. Item No. mm Inch 32837 200 8.0 Pkg. 1 lbs. .78 Toll Free: (800) 494-6104 36 Insulated NE Style Lineman's Pliers Insulated Pliers & Cutters New dynamic joint provides 40% easier cuts & significantly longer tool life Safety slip guard 1000volt 32831 Soft grip ergonomically designed handle body Cutters additionally induction hardened Insulated NE Style Lineman's Pliers. Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Long life edge is achieved through additional induction hardening to approx. 64HRC. Special C70 tool steel hardened & tempered. Extra long cutting edge for flat and round cables. Two component soft grip ergonomic handles. Item No. 32831 Hard chrome finish for long lasting corrosion protection mm 245 Inch 9.5 Pkg. 1 wt. 1.18 Insulated Linemans Pliers With Crimpers With Lower Crimping Jaw 5-In-1 Lineman's Pliers 1000volt 64HRC cutting edges 1000volt 32821 Insulated Lineman's Pliers "5-In-1" Professional Design Insulation According to EN/IEC, ASTM, NFPA70E & CSA, up to 1000 volt. Individually Tested. Deep cut radius conduit jaws for non-slip handling. Sure grip knurled & cross hatched flat jaw for non-slip griping. Extra long induction hardened precision matched cutting edges. Lower crimping jaw accepts most standard non-insulated electrical connectors. Large head with square anvil surface on each side. Made from premium CV tool steel forgings. Two component cushion grips for best user comfort. Item No. 32821 Insulated Combination Lineman's Pliers mm 225 Cutting Capacity Copper AWG Inch 9.0 #4 Pkg. wt. 1 .98 328 Combination Pliers. Insulation According to VDE 0682/ part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5746 Extra long cutting edge for flat & round cables. Serrated jaws. Cutting edges additionally induction hardened to approx. 64HRC. C70 Special tool steel, Chrome finish. Use for gripping and holding as well as cutting soft and hard wires and cables. Two component soft grip ergonomic handles. Item No. 32814 32816 32818 Insulated High Leverage Combination Pliers Cutting Capacity mm 160 180 200 Copper AWG Inch 6.3 #10 7.0 #9 8.0 #8 Pkg. 1 1 1 wt. .53 .58 .72 Insulated Crimping Pliers Lineman's 1000volt 32820 High Leverage Combination Pliers. Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5746 Extra long cutting edge for flat and round cables. Serrated jaws. Cutting edges additionally induction hardened to approx. 64HRC. C70 Special tool steel. Use for gripping, pulling & holding as well as cutting wires and cables ranging in hardness from soft to extremely hard. Two component soft grip ergonomic handles. 32841 Insulated Crimping Pliers. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Semi-circular profiles for secure connection between end sleeve and conductor. Long life is achieved through additional induction hardening to 64HRC. C70 special tool steel hardened & tempered. Item No. 32820 Item No. 32841 Cutting Capacity mm 225 Copper AWG Inch 9.0 #4 Pkg. wt. 1 .86 1000volt mm 180 Inch mm2 AWG Pkg. wt. 7.0 0.25-2.5 6-30 1 .57 www.wihatools.com 37 Insulated Diagonal Cutters Insulated Serrated Edge Cable Cutters 64HRC cutting edges 1000volt 1000volt 328 Diagonal Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5749 Low wear lap joint, riveted and able to withstand high levels of load. Lightweight action, clean cutting. Long term cutting is achieved through additional inductive hardening to approx. 60 HRC. Special tool steel hardened and tempered. For soft & medium hard wire. 32832 & 32834 for soft, hard & piano wire. Item No. 32830 32832 32834 Cutting Capacity Copper AWG mm Inch 140 5.5 160 6.3 180 7.0 #6 #6 #6 Pkg. 1 1 1 wt. .47 .49 .62 328 Serrated Edge Cable Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Light, clean cutting ground precision cutting edges. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Special tool steel, hardened & tempered. For cutting of copper & aluminum cables without crushing. Item No. mm Inch 32826 160 6.3 32828 200 8.0 O 16 20 mm2 50 60 Pkg. 1 1 lbs. .42 .67 Insulated Stripping Pliers Insulated High Leverage Diagonal Cutters 64HRC cutting edges 1000volt New dynamic joint provides 40% easier cuts & significantly longer tool life 1000volt 328 High Leverage Diagonal Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5749 Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. Lightweight action, clean cutting. Long term cutting is achieved through additional inductive hardening to approx. 64HRC. C70 special tool steel hardened and tempered to high quality. For soft, hard and piano wire, lay-on joint, optimized power transmission. Item No. 32835 32836 32838 mm 160 180 200 Cutting Capacity Copper AWG Inch Pkg. wt. 6.3 7.0 8.0 #6 #5 #4 1 1 1 Stripping Pliers. Insulation According to VDE 0682/part 32860 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 volt. Individually Tested. Heavy duty forged, induction hardened cutting edges for even stripping of insulation. Drop-forged from special tool steel, chrome and nickel plated, mirror-polished. Spring and adjusting screw, for stripping up to O 5mm/#4 Awg. Item No. 32860 Stripping Capacity mm 160 Copper AWG Inch 6.3 #8 - #28 Pkg. wt. 1 .50 .64 .67 .80 Insulated Electrician's Diagonal Cutters Insulated Stripping Pliers Strips AWG #10 & #14 1000volt 32861 Diagonal Cutters W/Stripping Holes. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Drop-forged from special tool steel, cutters additionally induction hardened to approx. 64HRC, chrome-nickel plated, mirror-polished. Ergo comfort grip with slip guard. Holes in the cutting edge for stripping copper wire of O 1.5 and 2.5. Item No. 32861 Cutting Capacity mm 160 Copper AWG Inch 6.3 #6 Pkg. wt. 1 .55 1000Volt 10250 Insulated Stripping Pliers. Insulation According to EN/IEC 60900, DIN ISO 8976, ASTM F-1505 & CSA Specification. Individually Tested. Wide long head with ridged gripping surface, shears blade and firm wire stripping stations. Wire stripping stations 0.81 / 1.0 / 1.3 / 1.6 / 2.0 / 2.59mm, AWG 20 / 18 / 16 / 14 / 12 / 10. Item No. mm Inch O AWG Pkg. lbs. 10250 160 6.3" 0.81-2.59 20-10 1 .26 Toll Free: (800) 494-6104 38 Insulated Round Nose Pliers Insulated Long Nose Pliers 1000volt 328 Long Nose Pliers With Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Drop-forged from special tool steel, cutters additionally induction hardened to approx. 64HRC, chrome-nickel plated, mirror-polished. Item No. 32806 32808 Cutting Capacity mm 160 200 Copper AWG Inch 6.3 #10 8.0 #8 Pkg. wt. 1 .32 1 .42 1000volt 32870 Round Nose Pliers. Insulation According to VDE 0682/ part 01, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Drop-forged from special tool steel, individually induction hardened, chrome and nickel plated, mirror-polished. Ergonomic comfort grip with slip guard. Serrated jaws. Item No. 32870 mm 160 Inch Pkg. 6.3 1 wt. .34 Insulated Long Flat Nose Pliers Insulated Bent Nose Pliers Angled 40 O 1000volt 1000volt 328 Bent Nose Pliers With Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Drop-forged from special tool steel, cutters additionally induction hardened to approx. 64HRC, chrome-nickel plated, mirror-polished. Serrated gripping surface, nose bent 40o. Item No. 32804 32807 Cutting Capacity mm 200 160 Copper AWG Inch 8.0 #8 6.3 #10 Pkg. wt. 1 .43 1 .32 32810 Long Flat Nose Pliers. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5745 Extra long head. Serrated Jaws are induction hardened. Special CV tool steel forgings, Chrome finish. Two component Soft Grip handles. Use for Gripping and right-angle bending of wires and sheet metal parts. Item No. 32810 mm 160 Inch 6.3 Pkg. 1 wt. .39 Wiha Canvas Pliers Holster * Canvas holster with belt clip and belt loop * Security pliers strap * Screwdriver holder in the front 91256 Item No. 91256 Pliers Canvas Holster Width Height Size Size lbs. pkg. 3.5 x 6.75 .15 1 Pen Style Control Cabinet Key For applications with all common switch cabinets and locking systems 21105 Pen Style Control Cabinet Key Diecast Zinc, polished finish. Includes: Square 5, 6, 7, 8mm, Triangular 9mm, Double Bit Key 5mm/Internal & 9mm/External, Universal 1/4" Bit Adapter, Magnetic Bit Holder & 2 Double Insert Bits: Slotted 7mm / Phillips #2, TORX T20/T25 Item No. mm Inch Pkg. lbs. 21105 140 5.5" 1 .30 Switch Cabinet Key 21103 Switch Cabinet Keys For applications with all common switch cabinets and locking systems. Diecast Zinc Item No. mm Inch Pkg. lbs. 76 3.0"1 .22 21103 www.wihatools.com 39 Wiha Inomic 1000Volt Insulated Pliers Proturn Insulated Electrician's Shears Award winning ergonomic design with head mounted at 23 angle to grip for reduced user fatigue Each tool includes a convenient jaw lock & handle return spring Heads drop forged CV premium tool steel Proturn Insulated Electrician's Shears 32951 Insulation meets VDE, ASTM F1505, EN/IEC 60900, CSA, NFPA 70E, OSHA Specifications. Made from stainless 420 grade steel Item No. mm Inch Pkg. lbs. 32951 160 6.3 1 .22 Meets VDE, EN/IEC, ASTM, CSA, NFPA standards 32850 32852 32854 1000volt 32850 Inomic Combo Pliers. Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5749 Precision machined forged head. Induction hardened for longest tool life. Cross hatched flat jaw & deep cut radius jaws for secure gripping of the work piece. Cutting edges are matched for precise cutting action. Award winning ergonomic design with head mounted at 23 angle to grip for reduced user fatigue. Palm side of grip has molded soft panel for added comfort in prolonged use. Item No. 32850 32852 Item No. 32852 32854 Item No. 32854 61630 Insulated Inch & Metric Folding Ruler 10,000Volt Tested/1000Volt Rated. Inch & Metric deep embossed scales. 10 folding sections. 30% fiberglass reinforced polyimide. Item No. Meter Inch Sections Increments 2 78" 10 1/16 & 1mm 61630 lbs. pkg. .31 1 Insulated Water Pump Pliers Cutting Capacity mm 180 Copper AWG Inch 7.0 #6 Pkg. lbs. 1 .46 Inomic Long Nose Pliers Cutting Capacity Copper AWG mm Inch 160 6.3 #6 Inomic Diagonal Cutters Pkg. lbs. 1 .43 Cutting Capacity mm 160 Copper AWG Inch 6.3 #6 Inomic Canvas Holster Width Height Size Size 4.0 x 4.5 1000volt 32954 Pkg. lbs. 1 .41 Holds any Inomic Pliers 91230 Item No. 91230 With Wire Puller Slot Insulated Industrial Water Pump Pliers. Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA, up to 1000 Volt. Individually Tested. 10 opening settings provides optimal adjustment to objects being gripped. Long life achieved through additional induction hardening of jaws to approx. 62HRC. Chromevanadium tool steel forgings, hardened and tempered. Black finish. Item No. 32954 Capacities mm 250 Round Hex Inch 10.0 1 3/4 2 Pkg. 1 wt. .90 Rapid & simple push button setting & locking 1000volt lbs. .05 pkg. 1 32956 Insulated Industrial Push Button Water Pump Pliers. Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA, Individually Tested. Extra narrow head for working in small spaces. Long life achieved through additional induction hardening of jaws to approx. 62HRC. Finger jam protection for safe operation at all settings. CVM tool steel forgings, hardened & tempered. Item No. 32956 Capacities mm 250 Round Hex Inch 10.0 1 3/4 2" Pkg. 1 wt. .90 Toll Free: (800) 494-6104 40 Insulated Industrial Pliers & Cutters Insulated Long Nose Pliers With Cutters Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards Industrial brushed finish 1000V Ergo comfort grip Induction hardened with slip guard jaws and cutters to 64 HRC Two component ergo cushion grip handles 1000volt 329 Insulated Industrial Long Nose Pliers With Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. Drop-forged from special tool steel, cutters additionally induction hardened to approx. 64HRC, half-round jaws, serrated gripping surface. New dynamic joint provides 40% easier cuts & significantly longer tool life Item No. 32926 32923 Cutting Capacity mm 160 200 Copper AWG Inch 6.3 #10 8.0 #8 Pkg. 1 1 wt. .36 .46 Insulated Lineman's Pliers With Crimpers Insulated High Leverage Diagonal Cutters 1000volt Long life high performance dynamic 60/40 joint 64HRC cutting edges 1000volt 32917 Insulated Industrial Lineman's Pliers "5-In-1" Professional Design. Insulation According to EN/IEC, ASTM, NFPA70E & CSA, up to 1000 volt. Individually Tested. Deep cut radius conduit jaws for non-slip handling. Sure grip knurled & cross hatched flat jaw for non-slip griping. Extra long induction hardened precision matched cutting edges. Lower crimping jaw accepts most standard non-insulated electrical connectors. Large head with square anvil surface on each side. Premium CV tool steel forgings. Cutting Capacity Item Copper AWG No. mm Inch Pkg. wt. 32917 225 9.0 #4 1 .98 32939 Insulated Industrial High Leverage Diagonal Cutters. Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA, 1000 volt rated. Individually Tested. DIN ISO 5749 Semi-circular. Low wear lap joint, riveted and able to withstand high levels of load. Lightweight action, clean cutting. Long term cutting is achieved through additional inductive hardening to approx. 64HRC. C70 special tool steel hardened and tempered to high quality. For soft, hard and piano wire, lay-on joint, optimized power transmission. Item No. 32939 Long life high performance dynamic 60/40 joint 1000volt 32938 Insulated NE Style Lineman's Pliers. Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Long life edge is achieved through additional induction hardening to approx. 64HRC. Special C70 tool steel hardened & tempered. Extra long cutting edge for flat and round cables. Item No. 32938 mm 245 Inch 9.5 Pkg. 1 wt. 1.18 Copper AWG Inch 8.0 #4 Pkg. wt. 1 .66 Insulated Diagonal Cutters Insulated NE Style Lineman's Pliers Knurled Striking Zone Cutting Capacity mm 200 Long life high performance dynamic 60/40 joint 1000volt 329 Insulated Industrial Diagonal Cutters. Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA, 1000Volt Rated. Individually Tested. DIN ISO 5749 Low wear lap joint, riveted and able to withstand high levels of load. Lightweight action, clean cutting. Long term cutting is achieved through additional inductive hardening to approx. 64HRC. Special tool steel hardened & tempered. For soft, medium hard wire & piano wire. Item No. 32933 32929 Cutting Capacity mm 160 200 Copper AWG Inch 6.3 #6 8.0 #6 Pkg. 1 1 wt. .64 .80 www.wihatools.com 41 Insulated Combo Pliers With Dynamic Joint 1000volt Insulated TriCut Strippers & Cutters 1000volt Long life high performance dynamic 60/40 joint 32930 Insulated Industrial High Leverage Combination Pliers. Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. DIN ISO 5746 Extra long cutting edge for flat and round cables. Serrated jaws. Cutting edges additionally induction hardened to approx. 64HRC. Use for gripping, pulling & holding as well as cutting wires and cables ranging in hardness from soft to extremely hard. 32944 Insulated Industrial TriCut Strippers & Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Induction hardened cutters & strippers. Cuts cable, strips cable, strips wire leads. Unique 3 in 1 design provides faster combined cutting and stripping. Strips AWG sizes #10 & #14. Item No. 32930 Item No. 32944 Cutting Capacity mm 200 Copper AWG Inch 8.0 #4 Pkg. 1 wt. .92 mm 170 AWG #6 Pkg. 1 wt. .58 Insulated Crimpers Insulated Heavy Duty Cable Cutters 1000volt Inch 6.7 1000volt 32945 32927 Insulated Industrial Serrated Edge Cable Cutters. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Light, clean cutting ground precision cutting edges. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. For cutting of copper & aluminum cables without crushing. Insulated Industrial Crimping Pliers. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Semi-circular profiles for secure connection between end sleeve and conductor. Long life is achieved through additional induction hardening to 64HRC. Crimps 6 - 30 AWG Connectors. Item No. mm Inch 32927 200 8.0 Item No. 32945 O 20 mm2 60 Pkg. 1 lbs. .78 mm 180 Inch 7.0 mm2 0.25-2.5 AWG 6-30 Pkg. 1 wt. .64 Insulated Stripping Pliers 1000volt 32947 Insulated Industrial Stripping Pliers. Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA, 1000Volt Rated. Individually Tested. DIN ISO 5745 Made from Premium CV tool steel forgings. Induction hardened jaws and cutters to 64HRC. Spring & adjusting screw, for stripping up to O 5mm/#4 Awg. Item No. 32947 Stripping Capacity mm 160 Copper AWG Inch 6.3 #8 - #28 Pkg. wt. 1 .46 Toll Free: (800) 494-6104 42 Insulated Industrial BiCut SuperCut Wiha Insulated Industrial Tool Sets Cutting capacity up to 3mm hardened piano wire Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards Individually Tested * * * * * 1000volt Double the power at the press of a button BiCut does the job of two pairs of pliers Up to 50% less hand strength required for cutting Cutting force doubled for extremely hard materials Easily switch between two strengths in one-handed operation 32936 Insulated Industrial BiCut SuperCut. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 Volt. Individually Tested. Durable cutting is achieved through additional inductive hardening to approx. 64HRC. Drop forged of high C70 steel. For cutting various materials from soft to extremely hard, such as nails, screws, bolts, wire cables, spring wires, chains, etc. Item No. mm Inch 32936 200 8.0 Pkg. 1 1000Volt 32981 Item No. 32981 3 Pc. Insulated Industrial Pliers & Cutters Insulated Pliers & Cutters 8.0" Combo Pliers, 8.0" Long Pliers, 8.0" Diagonal Cutters lbs. 2.18 lbs. .78 Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards Insulated BiCut SuperCut & Screwdriver Set Individually Tested Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards 1000Volt 32983 Item No. 32983 5 Pc. Insulated Industrial Diagonal Cutters & Screwdrivers Insulated Diagonal Cutters & Screwdrivers 6.3"/160mm Diagonal Cutter Insulated Drivers: Slotted: 3.0, 4.5mm * Phillips: #1, #2 lbs. 1.17 1000volt 32942 7 Pc. Insulated Industrial BiCut SuperCut & Screwdrivers Ergonomic two component molded grips. 10,000 Volt tested Item No. Insulated BiCut SuperCut: 32942 8.0"/200mm BiCut SuperCut Insulated Cushion Grip Screwdivers: lbs. Phillips: #0, #1, #2 1.86 Slotted: 3.0, 4.5, 5.5mm Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards Individually Tested 1000Volt 32984 Item No. 32984 6 Pc. Insulated Industrial Combo Pliers & Screwdrivers Insulated Combination Pliers & Screwdrivers 8.0" Combination Pliers & 8" Long Nose Pliers Drivers: Slotted: 3.0, 4.5mm * Phillips: #2 * Square: #2 lbs. 2.06 www.wihatools.com 43 Wiha Insulated Industrial Tool Sets Wiha Insulated Tool Tray Sets Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards 1000Volt 32982 3 Pc. Insulated Industrial Pliers/Cutters & Voltage Detector Item No. Insulated Pliers/Cutters & Cat. III Voltage Detector 32982 6.3" Long Pliers, 6.3" Diagonal Cutters Voltage Detector with both light and sound alerts lbs. .98 Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards 1000Volt Tool box set in blow molded tray Tool box set in blow molded trays 32989 28 Piece Insulated Industrial Pliers & Cutters Set Insulated pliers & cutters set in a light weight tool box tray. Item No. Set Includes: 9.0" Lineman's Pliers lbs. 32989 8.0" High Leverage Combo Pliers 6.34 6.3" & 8.0" Long Nose Pliers 8.0" Cable Cutters 6.3" & 8.0" Diagonal Cutters 6.3" Stripping Pliers 7.0" Crimping Pliers Slotted: 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm Phillips: #0, #1, #2, #3 Xeno Slotted/Phillips: #1, #2 & Square: #1, #2 Cat. III Voltage Detector - Battery Operated 32999 9 Piece Insulated Industrial Pliers & Cutters Set Insulated pliers & cutters set in a light weight tool box tray. Item No. 9.0" Lineman's Pliers 8.0" High Lev. Combo Pliers 32999 6.3" Long Nose Pliers 8.0" Cable Cutters 8.0" Long Nose Pliers 6.3" Stripping Pliers lbs. 6.3" Diagonal Cutters 7.0" Crimping Pliers 6.34 8.0" Diagonal Cutters In Belt Pack Pouch Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards 1000Volt 32985 Item No. 32985 7 Pc. Insulated Industrial Pliers/Cutters & Screwdrivers Insulated Pliers/Cutters & Screwdrivers 8.0" Combo Pliers, 6.3" Long Nose, 6.3" Diagonal Cutters Insulated Drivers: Slotted: 3.0, 4.5mm * Phillips: #1, #2 lbs. 2.30 Notes: Toll Free: (800) 494-6104 44 Wiha Insulated Industrial Tool Sets In Roll Out Pouch 1000Volt 32986 11 Pc. Pliers & Screwdriver Set. Insulation According to VDE 0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505, NFPA70E, up to 1000 volt. Individually Tested. In Roll Out Pouch Item# 32986 Set Includes: lbs. 3.62 6.3" Long Nose Pliers 6.3" Diagonal Cutters 8.0" Combination Pliers 6.3" Stripping Pliers Insulated Slotted: 3.0, 4.5, 5.5mm Insulated Phillips: #1, #2 Insulated Square: #1, #2 In Roll Out Pouch 1000Volt 32973 22 Pc. Pliers & Driver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. In molded tool box Item# 32973 Set Includes: lbs. 8.70 9.0" Linemans Pliers W/Cutters 8.0" Long Nose Pliers W/Cutter 8.0" Diagonal Cutters 50mm Cable Stripping Knife Insulated Slim Phillips: #1, 2 Insulated Slim Slotted: 3.5, 4.5mm Insulated Slim Xeno: #1, 2 Insulated Slim Square: #1, 2 Insulated T-handle Hex Inch: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8" Insulated Inch Nut Drivers: 3/8, 7/16, 1/4, 5/16" 1000Volt Now in canvas tool bag 1000Volt 32987 8 Pc. Pliers & Cutters Set. Insulation According to VDE 0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505, NFPA70E, up to 1000 volt. Individually Tested. In Roll Out Pouch Item# 32987 Set Includes: lbs. 5.52 6.3" Long Nose Pliers 6.3" Diagonal Cutters 8.0" Long Nose Pliers 8.0" H.D. Diagonal Cutters 9.0" Lineman's w/Cutters 6.3" Stripping Pliers 8.0" Cable Cutters 7.0" Crimpers 1000Volt In Roll Out Pouches 32988 22 Pc. Pliers & Cutters Set. Insulation According to VDE 0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505, NFPA70E, up to 1000 volt. Individually Tested. In Roll Out Pouches Item# 32988 Set Includes: lbs. 5.74 8.0" Long Nose Pliers 6.3" Diagonal Cutters 9.0" Lineman's w/Cutters 8.0" H.D. Diagonal Cutters 8.0" Cable Cutters 6.3" Stripping Pliers 7.0" Crimping Pliers 15 Pc. SlimLine Blade Set includes: Insulated SlimLine Blade Holder Slotted: 3.0, 4.0, 5.5, 6.5 Phillips: #1, #2 Xeno: #1, #2 : T8, T10, T15, T20 Square: #1, #2 32390 11 Pc. Pliers & Driver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. In canvas tool bag Item# 32390 Set Includes: lbs. 6.30 8.0" Linemans Pliers 6.3" Long Nose Pliers W/Cutter 8.0" Long Nose Pliers W/Cutter 6.3" Diagonal Cutter 8.0" High Leverage Cutter Insulated Phillips: #0, 1, 2 Insulated Slotted: 3.0, 4.5, 6.5mm 1000Volt 32399 10 Pc. Pliers & Driver Set. Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested. In canvas zipper pouch Item# 32399 Set Includes: lbs. 5.74 8.0" Linemans Pliers 8.0" Long Nose Pliers W/Cutter 8.0" Diagonal Cutter 6.3" Wire Stripper 10.0" Adjustable Pliers Insulated Phillips: #1, 2 Insulated Slotted: 3.0, 4.5, 6.5mm www.wihatools.com No Hassle Guarantee Wiha branded tools are regarded as the most durable, best designed and highly innovative products around. Our tools are used by demanding professional tradespeople and tool aficionados alike. They are meant to be used and utilized often. However, if you are not happy for any reason return them within 12 months of purchase with proof of purchase and we will Repair or Replace. Rest assured, if for some reason there is a defect in material or workmanship we will replace your tool free of charge for as long as you own the tool. Failures due to misuse, abuse or normal wear and tear are not covered by this guarantee. We stand by our products with what we believe is the best No Hassle Guarantee in the industry. Exclusions Wiha Tools has the right to exclude Bits, Tweezers and Ceramic Screwdrivers. These products are either consumable or wear easily. All torque tools are designed for 5,000 cycles or 1 year (whichever comes first). If a tool becomes out of specification within that period Wiha Tools will Repair or Replace. Visit www.wihatools.com to learn more about our Torque Control Service Program. Legal Some areas do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This guarantee gives you specific rights, and you may also have other rights, which vary, from state to state, province to province, or country to country. This No Hassle Guarantee is the sole and exclusive guarantee for the Willi Hahn Corporation dba Wiha Tools. No employee, agent, dealer, or other person is authorized to alter this guarantee or make any other guarantees on behalf of Wiha Tools. Willi Hahn Corporation USA Attn: No Hassle Guarantee 1348 Dundas Circle Monticello, MN 55362 800-494-6104 45 Toll Free: (800) 494-6104 46 Numerical Index by Item Number Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page 10250 11950 11960 11975 11980 12326 12327 12851 12852 12853 12854 12855 12856 12857 12858 12859 13650 13651 13652 13653 13654 13655 13656 13657 13658 13659 13662 13663 13664 13665 13666 13667 13668 13669 13670 13671 13672 13673 13690 13691 13693 13694 15000 15003 15050 19767 20006 20007 20008 20009 20010 20011 20012 20013 20014 20015 20016 20017 20018 20019 20020 20022 20024 20027 20030 20032 20091 20093 20131 20133 20135 20136 20137 20138 20140 20141 20142 20144 20145 20146 20147 20148 20149 20151 20154 20190 20192 20194 20196 21008 21009 21010 21011 21012 21013 21014 21015 21017 21019 21020 21022 21024 21027 21030 21032 21040 21042 21044 21046 21048 21050 21052 21054 21056 21057 21058 21060 21062 21064 21066 21068 21093 21094 6 21095 6 21096 6 21103 38 21105 38 21208 5 21210 5 21212 5 21213 5 21214 5 21217 5 21219 5 21290 5 21325 5 21327 5 21329 5 21331 5 21333 5 21335 5 21391 5 25500 25 25511 25 28301 18 28302 17,18 28304 18 28307 19 28308 19 28309 19 28310 19 28312 19 28315 19 28317 19 28319 19 28320 19 28321 19 28327 19 28329 19 28330 19 28331 19 28332 19 28333 19 28334 19 28335 19 28336 19 28337 19 28338 19 28339 19 28340 19 28341 19 28342 19 28343 19 28344 19 28346 19 28347 19 28350 17 28366 17 28367 17 28368 17 28369 17 28371 17 28390 18 28391 28392 28393 28394 28395 28396 28398 28399 28724 28726 28727 28734 28736 28738 28740 28741 28742 28750 28751 28752 28791 28792 29006 29009 29012 29240 29250 30114 30138 30152 30190 30192 30700 30701 30711 30712 30746 30747 30770 31326 31327 31328 31329 31330 31331 31332 31333 31334 31335 31336 31337 31338 31339 31340 31341 31342 31343 31344 31345 31350 31390 31391 31394 31395 31425 31428 31429 31430 31431 31432 31433 31434 31435 31436 31437 31438 31439 31450 31460 31491 31493 31495 31496 31506 31507 31508 31509 31510 31511 31512 31513 31514 31515 31516 31517 31518 31519 31520 31521 31522 31524 31590 31592 31595 31608 31609 31610 31611 31612 31613 31614 31615 31616 31617 31618 31619 31620 31621 31622 31623 31624 31626 37 13 14 14 14 13 11 10 11 13 10 10 11 11 13 13 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 7 7 7 13 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 5 5 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 18 18 17 17 17 17 18 18 17 17 17 17 17 17 16 16 16 16 16 16 16 16 10 11 13 13 13 16 16 16 16 16 25 25 25 25 20 20 21 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 9 9 11 11 11 11 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 11 11 11 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 www.wihatools.com 47 Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page 31627 31628 31630 31632 31650 31691 31694 31703 31704 31705 31707 31708 31709 31710 31712 31713 31714 31715 31716 31718 31720 31722 31790 31792 31805 31807 31809 31811 31813 31815 31817 31830 31832 31834 31836 31838 31840 31842 31844 31890 32000 32001 32002 32003 32004 32005 32010 32012 32015 32017 32023 32024 32025 32026 32027 32028 32031 32034 32039 32042 32045 32046 32049 32052 32055 32058 32079 32085 32087 32088 32089 32090 32091 32092 32093 32094 32095 32100 32101 32102 32103 32104 32105 32106 32107 32108 32145 32146 32188 32189 32190 32192 32196 32197 32198 32199 32206 32209 32212 32215 32218 32221 32224 32227 32230 32233 32236 32238 32239 32240 32241 32255 32258 32261 32264 32267 32268 32270 32273 32276 32278 32280 32288 32291 32292 32293 32294 32296 32302 32303 32304 32305 32306 32308 32366 32390 32399 32400 32401 32402 32403 32505 32511 32512 32513 32514 32515 32516 32517 32518 32519 32521 32526 32531 32536 32541 32546 32551 32556 32561 32566 32590 32592 32596 32800 32801 32804 32806 32807 32808 32810 32814 32816 32818 32820 32821 32826 32828 32830 32831 32832 32833 32834 32835 32836 32837 32838 32841 32850 32852 32854 32856 32857 32858 32860 32861 32862 32863 32864 32865 32867 32868 32869 32870 32871 32872 32873 32874 32875 32876 32877 32878 32879 32886 32888 32889 32891 32892 32894 32895 32896 32899 32917 32923 32926 32927 32929 32930 32933 32936 32938 32939 32942 32944 32945 32947 32951 32954 32956 32973 32981 32982 32983 32984 32985 32986 32987 32988 32989 32990 32999 33441 33443 33445 33447 33449 33478 33481 33482 33483 33485 33486 33487 33490 33532 33632 33634 33637 33641 35811 35812 35844 35845 35890 35891 38006 38007 38025 38050 38051 40800 61630 75205 75210 75215 75220 75302 75304 76208 76210 76212 76215 76290 91230 91256 12 12 12 12 9 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 20 20 20 20 20 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 22 20 20 20 20 20 21 20 25 20 25 22 23 23 23 23 23 22 22 22 22 22 22 20 20 20 20 20 23 21 23 23 21 21 21 25 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 26 24 24 24 24 24 24 24 44 44 25 25 25 25 24 24 20 20 20 20 24 20 20 20 24 24 24 24 24 24 24 24 24 24 24 24 21 29 29 38 38 38 38 38 36 36 36 36 36 37 37 37 36 37 35 37 37 37 35 37 36 39 39 39 34 34 34 37 37 35 35 35 34 33 33 33 38 28 28 28 31 28 30 30 31 31 28 32 33 32 32 32 32 31 33 40 40 40 41 40 41 40 42 40 40 42 41 41 41 39 39 39 44 42 43 42 42 43 44 44 44 43 28 43 15 15 15 15 15 15 15 15 15 15 15 15 15 22 15 15 15 15 24 24 20 20 24 24 27 27 27 27 27 13 39 14 14 14 14 14 14 7 7 7 7 7 39 38 Prop65 WARNING: This product could expose you to Chrome 6, DEHP & Phthalates. These chemicals are known to the state of California to cause cancer. For more information go to P65warnings.ca.gov/ Insulation Test Cold Impact Test Material Integrity Test Puncture Test Flame Resistance Test Adhesion Test Subject to change without notice (c)2018 Willi Hahn Corporation (R)Torx is a registered trademark of Acument Intellectual Properties LLC. (800) 494-6104 fax: (800) 494-7456 cservice@wihatools.com www.wihatools.com Wiha Quality Tools 1348 Dundas Circle Monticello, MN 55362 tel: 763.295.6591 fax: 763.295.6598 Wiha Tools Canada Ltd. www.wihatools.ca Brampton, ONT L6T 4X4 tel: 866.494.0096 or 763.295.6591 fax: 763.295.6598 To: Catalog Item No. 99919.wo version - 2/1/18 99951.wo - Bits Catalog 99004.wo - Shop Tools Catalog 99001.wo - TorqueControl Catalog 99934.wo - Hex Tools Catalog 99914.wo - TORX Catalog 99002.wo - Screwdrivers Catalog 91330.wo - Tooling Catalog 99006.wo - Tech Tools Catalog 99945.wo - ESD Catalog 99977.wo - Pliers/Crimpers Catalog Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Wiha: 32800 31395 31496 19767 31595 28391 28791 21391 32877 28390 28792 32876 32188