Description Page
Insulated Adjustable Wrenches 7
8.0, 10.0, 12.0, 15.0”
Wiha Insulated Adjustable Wrenches
Description Page
Ins. Hex Drive Bit Sockets 9
Wiha Insulated 3/8” Hex Drive Bit Sockets
Arc Flash Protection:
Wiha Insulated tools can be a vital component in your Arc Flash
protection strategy. What is Arc Flash?
ARC FLASH
An Arc Flash is an electrical explosion due to a fault condition or short
circuit when either a phase to ground or phase to phase conductor is
connected. Arc flashes cause electrical equipment to explode, resulting
in an arc-plasma fireball. Temperatures may exceed 35,000° F (the
surface of the sun is 9000° F). These high temperatures cause rapid
heating of surrounding air and extreme pressures, resulting in an arc
blast. The arc blast will likely vaporize all solid copper conductors which
will expand up to 67,000 times its original volume when it is vaporized.
The result of this violent event is usually destruction of the equipment
involved, fire, and severe injury or death to any nearby people.
WHY ARC FLASHES HAPPEN
There are a variety of reasons why an Arc Flash can occur, but most
of them are preventable. Most arc flashes occur when maintenance
workers are manipulating live equipment for testing or repair and
accidentally cause a fault. Improper tools, improper electrical
equipment, corrosion of equipment, improper work techniques and lack
of training are just some of the events that can lead to a devastating
arc flash or arc blast.
ARC FLASH COMPLIANCE
There are 4 main regulations that govern electrical safety & arc flash:
1. OSHA Standards 29CFR, Part 1910. Occupational Safety and
Health Standards. 1910 sub part S (electrical) Standard number
1910.333 specifically addresses Standards for Work Practices and
references NFPA 70E. OSHA 29CFR 1910.335 (a) (1)(i) requires the
use of protective equipment when working where a potential electrical
hazard exists and 29CFR 1910.132(d)(1) which requires the employer
assess the workplace for hazards and the need for personal protective
equipment. OSHA compliance is required by any plant building or facility.
2. The National Fire Protection Association (NFPA) Standard 70 -
2002 “The National Electrical Code” (NEC) contains requirements for
warning labels.
3. NFPA 70E provides guidance on implementing appropriate work
practices that are required to safeguard workers from injury while
working on or near exposed electrical conductors or circuit parts that
could become energized. Part II 2-1.3.3 regarding Arc Flash Analysis
states that a “Flash Hazard Analysis shall be done before a person
approaches any exposed electrical conductor or circuit part that has
not been placed in an electrical safe work condition”. This Arc Flash
Hazard Analysis must be done to determine the level of Personal
Protection Equipment PPE that a worker must use, and the Arc Flash
Boundary in inches along with the incident energy found at each
location. Each panel must be marked with an ANSI z535 approved Arc
Flash Warning Label.
4. The Institute of Electronics and Electrical Engineers (IEEE) 1584 –
2002 Guide to Performing Arc-Flash Hazard Calculations
copyright © information by: American Trainco, Inc.
http://www.martinarcflash.com
OSHA
Wiha tools assists with compliance of OSHA 29CFR 1910
(Sub Parts electrical standard)
Description Page
Insulated Open End Spanners 4-5
Insulated Ratchet Wrenches 5
Ins. Offset Ring Wrenches 6
Description Page
Insulated L-keys 8
Wiha Insulated L-keys
Description Page
Insulated Sockets 1/4, 3/8, 1/2” 9-12
Insulated Ratchets 10-13
Insulated T-handle 10-13
Insulated Extension Bars 10-13
Wiha Insulated Socket Accessories
Description Page
Insulated Knives 7
Wiha Insulated Electrician’s Knives
Description Page
Insulated Cable Cutters 13
Insulated WaterPump Pliers 13
Wiha Insulated Cable Cutters & Pliers
Wiha Insulated Wrenches
2
Toll Free: (800) 494-6104
Description Page
Insulated Pop-Up Sets 27-28
Wiha Insulated Pop-Up Insert Bit Sets
Description Page
Insulated Belt Pack Pouches 28
Pliers & Cutters
Pliers/Cutters & Screwdrivers
Pliers/Cutters & Multi Bit Set
Wiha Insulated Belt Pack Pouch Sets
Description Page
Insulated Inomic Pliers 39
Inomic Combo Pliers
Inomic Long Nose Pliers
Inomic Diagonal Cutters
Wiha Insulated Inomic Pliers
Description Page
Xeno Terminal Block 25
Combination Screwdrivers
Insulated TorqueControl 17
Handle & Blade Holder
Voltage Detectors 25
Insulated Hex
Inch/Metric T-handles 15
Insulated Slotted Drivers 22-23
Insulated Phillips Drivers 22-23
Insulated Torx® Drivers 24
Insulated Nut Drivers 26
Insulated Pozidriv® 25
Insulated Square Tip 24
Insulated Tweezers 14
Wiha Insulated Tools
Description Page
Insulated Multi-Bit Drivers 27
Wiha Insulated Multi-Bit Holders
Description Page
Insulated Combination Pliers 36
Insulated Heavy Duty 37
Diagonal Cutters
Insulated Pliers 38
Insulated Stripping Pliers 37
Insulated Pliers Sets 28-35
Wiha Insulated 1000Volt Pliers/Cutters
Description Page
Insulated Hacksaw 13
Wiha Insulated Hacksaw
Description Page
Insulated SlimLine Handles 18
Insulated SlimLine Blade Sets 17-18
Insulated SlimLine Blades 19
Insulated SlimLine Drivers 20
Insulated SlimLine Driver Sets 21
Wiha Insulated SlimLine Tools
3
Description Page
Insulated Industrial Pliers/Cutters 40-44
Wiha Insulated Industrial Pliers/Cutters
Description Page
Insulated Slotted Drivers 20
Insulated Phillips Drivers 20
Insulated PicoFinish Sets 20
Wiha Insulated Pico Finish Screwdrivers
Description Page
Insulated Pop-Up Sets 17
Wiha Insulated Pop-Up SlimLine Blade Sets
Description Page
Insulated Torque Ratchet 16
Wiha Insulated TorqueControl Tools
www.wihatools.com
Inch Open-End Wrenches, With
Insulated Handle Insulation According
to VDE Specification 0680 and EN/IEC
60900, DIN 7446 and CSA, up to 1000 Volt.
Individually Tested. Chrome-vanadium steel,
hardened. Angled 15O.
Item OAL OAL
No. Inch Inch mm lbs.
1/4 3.4 87.5 .04
5/16 3.9 100 .05
3/8 4.1 105 .09
7/16 4.6 117 .09
1/2 5.5 140 .15
9/16 5.7 146 .15
5/8 6.2 158 .20
11/16 6.5 165 .23
3/4 7.0 178 .33
13/16 7.5 191 .42
7/8 7.6 192 .44
15/16 7.9 201 .51
1 8.4 213 .61
1-1/16 9.2 233 .79
1-1/8 9.2 233 .77
1-1/4” 7.5
1-1/2” 7.5
* Lengths are +/- 5% due to coating process
Wiha Insulated Open-End Wrenches
1000Volt
14 Piece Insulated Inch Open
End Wrench Set
Item OAL OAL
No. Inch Inch Inch Inch lbs.
5/16 3.9 3/4 7.0 5.70
3/8 4.1 13/16 7.5
7/16 4.6 7/8 7.6
1/2 5.5 15/16 7.9
9/16 5.7 1 8.4
5/8 6.2 1-1/16 9.2
11/16 6.5 1-1/8 9.1
1000Volt
Angled 15O
Insulation Test Standards:
Insulation according to ASTM F-1505,
EN/IEC 60900, VDE 0680,
DIN 7446 and CSA
Each tool individually tested
to 10,000 Volts & certified to
1000 Volt ac or 1500 Volt dc
1000V
15 Piece Insulated Metric Open
End Wrench Set
Item OAL OAL
No. mm mm mm mm lbs.
6.0 97 14 150 3.0
7.0 98 15 151
8.0 104 16 164
9.0 108 17 162
10.0 107 19 178
11.0 118 22 196
12.0 129 24 211
13.0 137
1000Volt
8 Piece Insulated Inch Open End
Wrench Set
Item OAL OAL
No. Inch Inch Inch Inch lbs.
5/16 3.9 9/16 5.7 1.59
3/8 4.1 5/8 6.2
7/16 4.6 11/16 6.5
1/2 5.5 3/4 7.0
1000Volt
8 Piece Insulated Metric Open
End Wrench Set
Item OAL OAL
No. mm mm mm mm lbs.
6.0 97 13.0 137 1.4
7.0 98 14.0 150
8.0 104 17.0 162
10.0 107 19.0 178
1000Volt
Metric Open-End Wrenches,
With Insulated Handle
Item OAL OAL
No. mm mm Inch lbs.
6.0 97 3.8 .04
7.0 98 3.9 .05
8.0 104 4.1 .07
9.0 108 4.3 .07
10.0 107 4.2 .08
11.0 118 4.6 .11
12.0 129 5.1 .11
13.0 137 5.4 .19
14.0 150 5.9 .19
15.0 151 5.9 .17
16.0 164 6.5 .22
17.0 168 6.4 .24
18.0 173 6.8 .41
19.0 178 7.0 .32
20.0 190 6.9 .36
22.0 196 7.7 .39
24.0 211 8.3 .58
27.0 218 8.6 .68
30.0 235 9.3 .97
32.0 237 9.3 1.01
1000Volt
4
Insulation
High visibility,
grip is double
coated
Steel
Forged from chrome
vanadium, meets -
DIN 3110
20190
20190
20192
20192
20091
20091
20093
20093
20131
20133
20135
20136
20137
20138
20140
20141
20142
20144
20145
20146
20147
20148
20149
20151
20154
200
20006
20007
20008
20009
20010
20011
20012
20013
20014
20015
20016
20017
20018
20019
20020
20022
20024
20027
20030
20032
201
pkg.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
pkg.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Toll Free: (800) 494-6104
5
13 Piece Insulated Inch Open
End Wrench Set In Tool Box Tray
Item OAL OAL
No. Inch Inch Inch Inch lbs.
1/4 3.4 11/16 6.5 4.90
5/16 3.9 3/4 7.0
3/8 4.1 13/16 7.5
7/16 4.6 7/8 7.6
1/2 5.5 15/16 7.9
9/16 5.7 1 8.4
5/8 6.2
1000Volt
13 Pc. Insulated Metric Open
End Wrench Set In Tool Box Tray
Item OAL OAL
No. mm mm mm mm lbs.
8.0 104 16.0 164 4.90
10.0 107 17.0 168
11.0 118 18.0 173
12.0 129 19.0 178
13.0 137 22.0 196
14.0 150 24.0 211
15.0 151
In Tool
Box Tray
1000Volt
In Tool
Box Tray
Wiha Insulated
Open-End Wrenches
Inch Insulated Ratchet Wrenches,
With Insulated Handle Insulation According
to EN/IEC 60900, ISO 3110 Specification,
Up To 1000 Volt. Individually Tested.
Blade chrome-vanadium steel, hardened.
Item OAL OAL
No. Inch mm Inch lbs.
3/8 140 5.5 .14
7/16 143 5.6 .15
1/2 154 6.1 .18
9/16 162 6.4 .22
5/8 177 7.0 .30
3/4 209 8.2 .46
Wiha Insulated Ratchet Wrenches
1000Volt
6 Piece Inch Insulated Ratchet
Wrenches Set
Item OAL OAL
No. Inch Inch Inch Inch lbs.
3/8 5.5 9/16 6.4 1.95
7/16 5.6 5/8 7.0
1/2 6.1 3/4 8.2
1000Volt
Steel
Forged from chrome
vanadium, meets - DIN 3110
Insulation Test Standards:
Insulation according to ASTM F-1505,
EN/IEC 60900, ISO 3110 and
CSA Specification
Metric Insulated Ratchet Wrenches,
With Insulated Handle Insulation According
to EN/IEC 60900, ISO 3110 Specification,
Up To 1000 Volt. Individually Tested.
Blade chrome-vanadium steel, hardened.
Item OAL OAL
No. mm mm Inch lbs.
8.0 125 4.9 .08
10.0 140 5.5 .12
12.0 150 5.9 .18
13.0 152 6.0 .18
14.0 163 6.4 .22
17.0 193 7.6 .38
19.0 210 8.3 .45
1000Volt
7 Piece Metric Insulated Ratchet
Wrenches Set
Item OAL OAL
No. mm mm mm mm lbs.
8.0 4.9 14.0 6.4 2.10
10.0 5.5 17.0 7.6
12.0 5.9 19.0 8.3
13.0 6.0
1000Volt
Each tool individually tested
to 10,000 Volts & certified to
1000 Volt ac or 1500 Volt dc
1000V
20194
20194
20196
20196
213
21391
21325
21327
21329
21331
21333
21335
212
21208
21210
21212
21213
21214
21217
21219
21391
21290
21290
pkg.
1
1
1
1
1
1
1
pkg.
1
1
1
1
1
1
www.wihatools.com
Steel Forged from
chrome vanadium,
meets - DIN 3110
Insulation Test Standards:
Insulation according to ASTM
F-1505, EN/IEC 60900,
ISO 3110 and CSA
Specification
Each tool individually
tested to 10,000 Volts &
certified to 1000 Volt ac
or 1500 Volt dc
8 Piece Metric Insulated Offset
Ring Wrenches Set
Item No. Metric:
10.0, 11.0, 12.0, 13.0, lbs,
14.0, 15.0, 17.0, 19.0mm 3.20
6
Wiha Insulated Deep Offset Ring Wrenches
Insulated Metric Offset Ring
Wrenches, Insulation According to EN/IEC
60900, ISO 3110 Specification, Up To 1000
Volt. Individually Tested. Blade Chrome-
Vanadium steel, hardened.
Item OAL OAL
No. mm mm Inch lbs.
8.0 159 6.3 .16
9.0 159 6.3 .18
10.0 171 6.8 .20
11.0 178 7.0 .22
12.0 191 7.5 .30
13.0 194 7.6 .30
14.0 203 8.0 .34
15.0 203 8.0 .34
17.0 219 8.6 .44
19.0 241 9.5 .52
20.0 250 9.8 .58
22.0 257 10.1 .64
24.0 279 11.0 .90
27.0 286 11.3 .96
30.0 311 12.3 1.28
32.0 318 12.5 1.38
1000Volt
1000Volt
16 Piece Metric Insulated Offset
Ring Wrenches Set
Item No. Metric:
8.0, 9.0, 10.0, 11.0, 12.0, 13.0,
14.0, 15.0, 17.0, 19.0, 20.0, 22.0,
lbs. 8.70 24.0, 27.0, 30.0, 32.0mm
Insulated Inch Offset Ring
Wrenches Blade CV steel, hardened.
Item
No. Inch lbs. pkg.
1/4 .16 1
5/16 .18 1
3/8 .20 1
7/16 .22 1
1/2 .30 1
9/16 .30 1
5/8 .34 1
11/16 .34 1
3/4 .44 1
25/32 .58 1
13/16 .52 1
7/8 .64 1
15/16 .90 1
1.0 .96 1
1-1/16 1.28 1
1-1/4 1.38 1
1000Volt
1000Volt
16 Piece Inch Insulated Offset
Ring Wrenches Set
Item No. Inch:
1/4, 5/16, 3/8, 7/16, 1/2, lbs.
9/16, 5/8, 11/16, 3/4, 8.70
25/32, 13/16, 7/8, 15/16,
1, 1-1/16, 1-1/4”
8 Piece Inch Insulated Offset
Ring Wrenches Set
Item No. Inch:
5/16, 3/8, 7/16, 1/2, 9/16, lbs.
5/8, 11/16, 3/4” 3.20
1000Volt
1000V
1000Volt
Use & Care Guide For Insulated Tools:
Store tools to minimize risk of damage to insulation, always wear approved eye protection, Inspect
insulation prior to each use of any insulated tool. Use insulated tools where the ambient temperature
is between -20 to +70O C. Have a qualified safety technician visually inspect insulation on tools
annually for safe use.
21095
21095
210
21008
21009
21010
21011
21012
21013
21014
21015
21017
21019
21020
21022
21024
21027
21030
21032
21093
21093
21040
21042
21044
21046
21048
21050
21052
21054
21056
21057
21058
21060
21062
21064
21066
21068
210
21094
21094
21096
21096
pkg.
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Toll Free: (800) 494-6104
7
Insulated Electrician’s Cable
Stripping Knife, With Insulated Handle,
Insulation According To VDE Specification,
Up To 1000 Volt. Individually Tested.
Blade tool steel, hardened, molded directly on.
Cover included.
Item Blade OAL OAL
No. mm mm Inch lbs.
50 216 8.5 .30
1000Volt
Insulated Electrician’s Cable
Stripping Knife, With Insulated Handle,
Insulation According To VDE Specification,
Up To 1000 Volt. Individually Tested.
Straight, partly insulated, strong blade.
Insulation molded directly on. Cover included.
Item Blade OAL OAL
No. mm mm Inch lbs.
50 230 9.0 .23
1000Volt
Insulated Stripping Knife,
With Insulated Handle
Insulation According To VDE
Specification, Up To 1000 Volt.
Individually Tested. Blade tool steel,
hardened. Insulation molded directly on.
Hooked cutting edge, half-round ground.
Cover included.
Item Blade OAL OAL
No. mm mm Inch lbs.
35 222 8.75 .22
1000Volt
Wiha Insulated Electrician’s Knives
Insulation Test Standards:
Insulation according to
ASTM, EN/IEC, VDE
& CSA Specification
Individually tested
Each tool individually tested to 10,000 volts &
rated to 1000Volt ac or 1500Volt dc
1000V
Insulation
molded on for
permanent bonding
Insulated 8” Adjustable Wrench
Insulation According to ASTM, EN/IEC,
NFPA, CSA and ISO Specification, up to
1000 Volt. Individually Tested. Etched on
scale for pre-setting size. Slip guard handle for
added protection.
Item OAL OAL Capacity
No. Inch mm Opening lbs.
8.0 200 1” .7
1000Volt
Insulated 10” Adjustable Wrench
Etched on scale for pre-setting size.
Slip guard handle for added protection.
Item OAL OAL Capacity
No. Inch mm Opening lbs.
10.0 250 1-1/4” 1.4
Insulated 12” Adjustable Wrench
Etched on scale for pre-setting size.
Slip guard handle for added protection.
Item OAL OAL Capacity
No. Inch mm Opening lbs.
12.0 300 1-1/2” 1.9
Insulated 15” Adjustable Wrench
Etched on scale for pre-setting size.
Slip guard handle for added protection.
Item OAL OAL Capacity
No. Inch mm Opening lbs.
15.0 380 1-11/16” 2.8
1000Volt
Wiha Insulated
Adjustable Wrenches
3 Pc. Insulated Adjustable
Wrenches
Etched on scale for pre-setting
size. Slip guard handle for added protection.
Item No. Set includes the following:
8.0”, 10.0”, 12.0” Adjustable Pliers
lbs. 4.0
1000Volt
1000Volt
WARNING!
Insulated Tools are intended to provide protection against accidental contact with charged energized
circuits. For maximum safety we recommend de-energizing all circuits whenever possible before
starting work on electrical apparatus or conductors. Always visually inspect insulation on tools before
use, do not use tools if insulation shows signs of wear or damage to the insulated areas of the tool.
Wear appropriate eye protection when using hand tools. Use NFPA70E certified insulated protective
outer wear when appropriate.
1000Volt
15000
15000
15003
15003
15050
15050
76208
76208
76210
76210
76212
76212
76215
76215
76290
76290
pkg.
1
pkg.
1
pkg.
1
pkg.
1
pkg.
1
pkg.
1
pkg.
1
www.wihatools.com
8
Wiha Insulated Hex L-keys
Insulation Test Standards:
Insulation according to ASTM,
F-1505, EN/IEC 60900
and CSA
Inch Insulated Hex L-keys, With
Insulated Handle. Insulation According to
IEC 60900 Specification, Up To 1000 Volt.
Individually Tested. Blade chrome-vanadium
steel, hardened.
Item OAL OAL
No. Inch mm Inch lbs.
1/16 79 3.1 .05
5/64 84 3.3 .05
3/32 89 3.5 .05
7/64 94 3.7 .06
1/8 104 4.1 .06
5/32 104 4.1 .06
3/16 134 5.3 .10
7/32 134 5.3 .12
1/4 134 5.3 .16
5/16 144 5.7 .24
3/8 234 9.2 .51
1/2 234 9.2 .77
1000Volt
Metric Insulated Hex L-keys, With
Insulated Handle. Insulation According to
IEC 60900 Specification, Up To 1000 Volt.
Individually Tested. Blade chrome-vanadium
steel, hardened.
Item OAL OAL
No. mm mm Inch lbs.
1.5 100 3.9 .09
2.0 105 4.1 .09
2.5 115 4.5 .09
3.0 130 5.1 .10
4.0 120 4.7 .10
5.0 140 5.5 .10
6.0 140 5.5 .13
8.0 150 5.9 .24
10.0 220 8.7 .51
12.0 260 10.2 .77
1000Volt
8 Piece Insulated Inch Hex
L-key Set
Item OAL OAL
No. Inch Inch Inch Inch lbs.
1/8 4.1 1/4 5.3 2.17
5/32 4.1 5/16 5.7
3/16 5.3 3/8 9.2
7/32 5.3 1/2 9.2
1000Volt
7 Piece Insulated Metric Hex
L-key Set
Item OAL OAL
No. mm mm mm mm lbs.
3.0 130 8.0 150 2.07
4.0 120 10.0 220
5.0 140 12.0 260
6.0 140
Each tool
individually
tested to
10,000 Volts &
certified to
1000 Volt ac or
1500 Volt dc
1000V
Insulation
Applied directly onto
blade for permanent
bonding
10 Piece Insulated Metric Hex
L-key Set
Item OAL OAL
No. mm mm mm mm lbs.
1.5 100 5.0 140 2.26
2.0 105 6.0 140
2.5 115 8.0 150
3.0 130 10.0 220
4.0 120 12.0 260
1000Volt
12 Pc. Insulated Inch Hex L-key Set
Item OAL OAL
No. Inch Inch Inch Inch lbs.
1/16 3.1 3/16 5.3 2.40
5/64 3.3 7/32 5.3
3/32 3.5 1/4 5.3
7/64 3.7 5/16 5.7
1/8 4.1 3/8 9.2
5/32 4.1 1/2 9.2
1000Volt
1000Volt
13670
13671
13672
13673
13663
13665
13666
13667
13668
13669
13662
13664
136
13650
13651
13652
13653
13654
13655
13656
13658
13659
13657
136
13690
13690
13691
13691
13693
13693
13694
13694
pkg.
1
1
1
1
1
1
1
1
1
1
1
1
pkg.
1
1
1
1
1
1
1
1
1
1
Toll Free: (800) 494-6104
9
Wiha Insulated
Hex Bit Sockets
1000Volt
7 Pc. Insulated 3/8” Drive Socket
Set - Inch
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
3/16, 7/32, 1/4, 5/16, 3/8,
lbs. 1.7 7/16, 1/2”
Insulated 3/8” Drive Sockets
Chrome-vanadium steel, forged, oil-hardened.
Item OAL
No. Inch Inch lbs. pkg.
3/16 3.1” .13 1
7/32 3.1” .14 1
1/4 3.1” .14 1
5/16 3.1” .16 1
3/8 3.1” .18 1
7/16 3.1” .20 1
1/2 3.1” .22 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
Wiha Insulated 1/4” Sockets, Accessories & Sets
Insulated 1/4” Drive Sockets-6
Point, Insulation According To ASTM
F-1505, DIN 7448 & CSA Specification, Up
To 1000 Volt. Individually Tested. Chrome-
vanadium steel, forged, oil-hardened.
Item
No. Inch lbs. pkg.
3/16 .03 1
7/32 .03 1
1/4 .03 1
9/32 .04 1
5/16 .04 1
11/32 .05 1
3/8 .05 1
7/16 .06 1
1/2 .07 1
9/16 .07 1
*Sockets must be used with insulated ratchets & extensions
Insulated 1/4” Drive Sockets-6
Point, Insulation According
Chrome-vanadium steel, forged, oil-hardened.
Item
No. mm lbs. pkg.
5.0 .03 1
6.0 .03 1
7.0 .03 1
8.0 .04 1
9.0 .04 1
10.0 .05 1
11.0 .05 1
12.0 .06 1
13.0 .06 1
14.0 .07 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
Metric -
6 Point
1000Volt
13 Pc Insulated 1/4” Drive Socket
Set - Inch
CV steel, forged, oil-hardened
sockets. Insulated after EN/IEC 60900.
Item No. Set includes the following:
3/16, 7/32, 1/4, 9/32, 5/16, 11/32,
3/8, 7/16, 1/2, 9/16”
lbs. 1.39 1/4” x 50mm Extension Bar
1/4” x 100mm Extension Bar
1/4” Ratchet - 140mm
1000Volt
13 Pc. Insulated 1/4” Drive Socket
Set - Metric
CV steel, forged, oil-hardened
sockets. Insulated after EN/IEC 60900.
Item No. Set includes the following:
5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm
1/4” x 50mm Extension Bar
lbs. 1/4” x 100mm Extension Bar
1.41 1/4” Ratchet - 140mm
Insulated 1/2” Drive Sockets
Chrome-vanadium steel, forged, oil-hardened.
Item OAL
No. Inch Inch lbs. pkg.
1/4 2.75 .22 1
5/16 2.75 .24 1
3/8 2.75 .25 1
7/16 3.63 .31 1
1/2 3.63 .34 1
9/16 3.63 .36 1
5/8 3.63 .42 1
3/4 3.63 .51 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
1000Volt
Metric -
6 Point
Wiha Insulated Socket Adapters / Reducers
Insulated Socket Adapters / Reducers CV
steel, forged, oil-hardened.
Item
No. Size lbs. pkg.
1/4 - 3/8 . 1
3/8 - 1/2 . 1
3/8 - 1/4 . 1
1/2 - 3/8 . 1
#31650
#31450 #31460
1000Volt
318
31805
31807
31809
31811
31813
31815
31817
31890
31890
313
31336
31337
31338
31339
31340
31341
31342
31343
31344
31345
313
31326
31327
31328
31329
31330
31331
31332
31333
31334
31335
31390
31390
31391
31391
31830
31832
31834
31836
31838
31840
31842
31844
318
31350
31450
31460
31650
www.wihatools.com
10
Insulated 1/4” Extension Bars,
ASTM F-1505, EN/IEC 60900 & CSA
Chrome-Vanadium steel.
Item OAL OAL
No. Inch mm Inch lbs.
1/4” 50 2.0 .08
1/4” 100 3.9 .12
1000Volt
Insulated 1/4” Drive T-handle,
With Insulated Handle. Insulation according
to EN/IEC 60900 & CSA specification, up
to 1000 Volt. Individually Tested. Blade CV
steel, hardened.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
1/4 160 6.2” .57 1
1000Volt
1000Volt
11 Piece Insulated 1/4” T-handle
& Socket Set - Metric
CV steel, forged,
oil-hardened sockets. Insulated after
EN/IEC 60900.
Item No. Set includes the following:
5, 6, 7, 8, 9, 10, 11, 12, 13, 14mm
lbs. 1.40 Insulated 1/4” T-handle
Each tool individually tested
to 10,000 volts & certified to
1000Volt ac or 1500Volt dc
Wiha Insulated 1/4” Sets & Accessories
1000Volt
11 Pc. Insulated 1/4” T-handle &
Socket Set-Inch
CV steel, forged, oil-hardened
sockets. Insulated after EN/IEC 60900.
Item No. Set includes the following:
3/16, 7/32, 1/4, 9/32, 5/16, 11/32,
3/8, 7/16, 1/2, 9/16”
lbs. 1.40 Insulated 1/4” T-handle
Insulated 1/4” Drive Ratchet,
EN/IEC 60900 & CSA Chrome-Vanadium
steel. Thumb lever for rapid reverse.
Item OAL OAL
No. Inch mm Inch lbs.
1/4” 140 5.5 .28
1000Volt
Wiha Insulated 3/8” Sockets
Insulated 3/8” Drive Sockets -
Insulation according to EN/IEC 60900, DIN
7448 & CSA specification, up to 1000 Volt.
Individually Tested.
CV steel, forged, oil-hardened.
Item
No. Inch lbs. pkg.
1/4 .07 1
9/32 .07 1
5/16 .07 1
11/32 .07 1
3/8 .08 1
7/16 .08 1
1/2 .10 1
9/16 .10 1
5/8 .10 1
11/16 .13 1
3/4 .14 1
13/16 .17 1
7/8 .18 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
Insulated 3/8” Drive Sockets-
Metric Insulation according to VDE, EN/IEC
60900, DIN 7448 & CSA specification, up
to 1000 Volt. Individually Tested. Chrome-
vanadium steel, forged, oil-hardened.
Item
No. mm lbs. pkg.
6.0 .07 1
7.0 .07 1
8.0 .07 1
9.0 .07 1
10.0 .07 1
11.0 .08 1
12.0 .10 1
13.0 .10 1
14.0 .10 1
15.0 .10 1
16.0 .10 1
17.0 .11 1
18.0 .12 1
19.0 .14 1
20.0 .15 1
21.0 .17 1
22.0 .18 1
24.0 .26 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
31395
31395
29006
29006
128
12854
12855
31394
31394
12851
12851
31425
31428
31429
31430
31431
31432
31433
31434
31435
31436
31437
31438
31439
314
31506
31507
31508
31509
31510
31511
31512
31513
31514
31515
31516
31517
31518
31519
31520
31521
31522
31524
315
pkg.
1
pkg.
1
1
Toll Free: (800) 494-6104
11
1000Volt
10 Pc. Insulated 3/8” Drive Socket
Set - Inch
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
5/16, 3/8, 7/16, 1/2,
9/16, 5/8, 11/16, 3/4”
lbs. 2.50 3/8” x 125mm Extension Bar
3/8” Ratchet - 190mm
10 Pc. Insulated 3/8” Drive Socket
Set - Metric
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
8, 10, 11, 12, 13, 14, 17, 19mm
3/8” x 125mm Extension Bar
lbs. 2.50 3/8” Ratchet - 190mm
16 Piece Insulated 3/8” Drive
Socket Set - Inch/Metric
CV steel, forged, oil-
hardened sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
5/16, 3/8, 7/16, 1/2,
9/16, 5/8, 11/16, 3/4”
lbs. 2.01 8, 10, 11, 12, 13, 14, 17, 19mm
Wiha Insulated 3/8” Sockets & Sets
1000Volt
24 Pc. Insulated 3/8” Drive Socket
Set - Inch
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
1/4, 9/32, 5/16, 11/32, 3/8, 7/16
1/2, 9/16, 5/8,11/16, 3/4” Sockets
lbs. 3/8” x 125mm Extension Bar
9.07 3/8” x 250mm Extension Bar
3/8” Ratchet - 190mm
Insulated Electrician’s Knife - 50mm
Slotted: 3.5, 4.5, 6.5mm
Phillips: #1, 2, 3
6.3” Long Nose Pliers
8.0” Combo Pliers
6.3” Diagonal Cutters
*Sockets must be used with insulated ratchets & extensions
24 Pc. Insulated 3/8” Drive Socket
Set - Metric
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
6, 7, 8, 9, 10, 11, 12,
13, 14, 17, 19mm Sockets
lbs. 3/8” x 125mm Extension Bar
9.08 3/8” x 250mm Extension Bar
3/8” Ratchet - 190mm
Insulated Electrician’s Knife - 50mm
Slotted: 3.5, 4.5, 6.5mm
Phillips: #1, 2, 3
6.3” Long Nose Pliers
8.0” Combo Pliers
6.3” Diagonal Cutters
*Sockets must be used with insulated ratchets & extensions
Insulated 3/8” Drive Ratchet,
EN/IEC 60900 CV steel. Socket release
button. Thumb lever for rapid reverse.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
3/8” 190 7.5 .93 1
1000Volt
Insulated 3/8” Extension Bars,
EN/IEC 60900 Chrome-Vanadium steel.
Item OAL OAL
No. Inch mm Inch lbs.
3/8” 125 4.9 .41
3/8” 250 9.8 .57
1000Volt
Insulated 3/8” Drive T-handle Or
Breaker Bar. Insulation according to
EN/IEC 60900 specification, up to 1000Volt
Rated. Individually Tested. Blade chrome-
vanadium steel, hardened.
Item OAL OAL
No. Inch mm Inch lbs.
3/8 200 7.9” .55
3/8 216 8.5” .68
1000Volt
Wiha Insulated
3/8” Socket Accessories
10 Pc. Insulated 3/8” T-handle &
Socket Set - MM
CV steel, forged, oil-hardened
sockets. Insulated after EN/IEC 60900.
Item No. Set includes the following:
8, 10, 11, 12, 13, 14, 17, 19mm
3/8” x 125mm Extension Bar
lbs. 2.47 Ins. 3/8” T-handle
1000Volt
10 Pc. Insulated 3/8” T-handle &
Socket Set-Inch
CV steel, forged, oil-hardened
sockets. Insulated after EN/IEC 60900.
Item No. Set includes the following:
5/16, 3/8, 7/16, 1/2, 9/16, 5/8,
11/16, 3/4”
lbs. 2.47 3/8” x 125mm Extension Bar
Insulated 3/8” T-handle
#12327
#29009
1000Volt
1000Volt
1000Volt
31493
31493
31590
31590
31491
31491
31495
31495
31592
31592
31496
31496
31595
31595
12852
12852
128
12856
12857
1000Volt
29009
12327
pkg.
1
1
pkg.
1
1
www.wihatools.com
12
Wiha Insulated 1/2” Sockets & Sets
Insulated 1/2” Drive Sockets -
Insulation According to ASTM, DIN & CSA
Specification, Up To 1000Volt. Individually
Tested. CV steel, forged, oil-hardened.
Item
No. Inch lbs. pkg.
5/16 .16 1
11/32 .16 1
3/8 .16 1
7/16 .16 1
1/2 .16 1
9/16 .17 1
5/8 .19 1
11/16 .19 1
3/4 .21 1
13/16 .23 1
7/8 .27 1
15/16 .35 1
1 .33 1
1-1/8 .44 1
1-1/4 .58 1
*Sockets must be used with insulated ratchets & extensions
1000Volt
Insulated 1/2” Drive Sockets -
Metric 1000 Volt.
Item
No. mm lbs. pkg.
8.0 .15 1
9.0 .15 1
10.0 .16 1
11.0 .16 1
12.0 .16 1
13.0 .17 1
14.0 .17 1
15.0 .17 1
16.0 .19 1
17.0 .19 1
18.0 .20 1
19.0 .21 1
20.0 .25 1
21.0 .25 1
22.0 .28 1
23.0 .29 1
24.0 .30 1
26.0 .37 1
27.0 .41 1
28.0 .44 1
30.0 .51 1
32.0 .55 1
1000Volt
Individually Tested
*Sockets must be used with insulated ratchets & extensions
1000Volt
1000Volt
24 Piece Insulated 1/2” Drive
Socket Set - Inch
CV steel, forged, oil-
hardened sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4,
13/16, 7/8, 15/16, 1” Sockets
1/2” x 125mm Extension Bar
lbs. 1/2” x 250mm Extension Bar
11.41 1/2” Ratchet - 260mm
Ins. Electrician’s Knife - 50mm
Slotted: 3.5, 4.5, 6.5mm
Phillips: #1, 2, 3
6.3” Long Nose Pliers
8.0” Combo Pliers
6.3” Diagonal Cutters
24 Piece Insulated 1/2” Drive
Socket Set - Metric
CV steel, forged, oil-
hardened sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
8, 9, 10, 12, 13, 14, 15, 17,
19, 22, 24mm Sockets
1/2” x 125mm Extension Bar
lbs. 1/2” x 250mm Extension Bar
11.39 1/2” Ratchet - 260mm
Ins. Electrician’s Knife - 50mm
Slotted: 3.5, 4.5, 6.5mm
Phillips: #1, 2, 3
6.3” Long Nose Pliers
8.0” Combo Pliers
6.3” Diagonal Cutters
Metric
Each tool individually tested
to 10,000 volts & certified to
1000Volt ac or 1500Volt dc
Inch
14 Pc. Insulated 1/2” Drive Socket
Set - Inch
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
3/8, 7/16, 1/2, 9/16, 5/8, 11/16,
3/4, 13/16, 7/8, 15/16, 1”
lbs. 1/2” x 125mm Extension Bar
7.64 1/2” x 250mm Extension Bar
1/2” Ratchet - 190mm
1000Volt
14 Pc. Insulated 1/2” Drive
Socket Set - Metric
CV steel, forged, oil-
hardened sockets. Insulated to EN/IEC 60900.
Item No. Set includes the following:
8, 9, 10, 11, 12, 13, 14,
17, 19, 22, 24mm
lbs. 1/2” x 125mm Extension Bar
7.64 1/2” x 250mm Extension Bar
1/2” Ratchet - 190mm
1000Volt
Each tool individually tested
to 10,000 volts & certified to
1000Volt ac or 1500Volt dc
31703
31704
31705
31707
31708
31709
31710
31712
31713
31714
31715
31716
31718
31720
31722
31608
31609
31610
31611
31612
31613
31614
31615
31616
31617
31618
31619
31620
31621
31622
31623
31624
31626
31627
31628
31630
31632
317
316
31790
31790
31691
31691
31792
31792
31694
31694
Toll Free: (800) 494-6104
13
Insulated 1/2” Drive Ratchet,
IEC/EN 60900 & CSA
Chrome-Vanadium steel. Reversible.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
1/2” 260 10.2 1.55 1
1000Volt
Insulated 1/2” Extension Bars,
EN/IEC 60900 & CSA
Chrome-vanadium steel.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
1/2” 125 4.9 .45 1
1/2” 250 9.8 .91 1
1000Volt
Wiha Insulated
1/2” Socket accessories
Insulated 1/2” Drive T-handle,
With Insulated Handle. Insulation according
to EN/IEC 60900 & CSA Specification, Up
To 1000 Volt. Individually Tested Blade VC
steel, hardened.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
1/2 200 7.9” .68 1
1000Volt
Insulated 1/2” Drive Breaker Bar,
IEC/EN 60900 & CSA
Chrome-Vanadium steel.
Item OAL OAL
No. Inch mm Inch lbs. pkg.
1/2” 267 10.5 1.04 1
1000Volt
Waterpump Pliers, With
Insulated Handle. Insulation According to
EN/IEC 60900, DIN ISO 8976, ASTM F-1505
& CSA Specification, Up To 1000 Volt.
Individually Tested Box joint. Chrome-
vanadium steel, drop forged, oil hardened.
Item OAL OAL Capacity
No. mm Inch mm lbs.
240 9.5 7/8” 1.1
1000Volt
Hacksaw, With Insulated Handle
Insulation According to EN/IEC 60900, DIN
ISO, ASTM & CSA Specification,
Up To 1000 Volt. Individually Tested.
Item OAL OAL
No. mm Inch lbs. pkg.
457mm 18.0” 1.92 1
1000Volt
Uses standard 12” blade
Wiha Insulated Hacksaw
Insulated Waterpump Pliers
Cable Cutter, With Insulated
Handle. Insulation According to EN/IEC,
ASTM & CSA Specification, Up To 1000
Volt. Individually Tested. Blade alloyed tool
steel. Induction hardened.
Item OAL OAL Capacity
No. mm Inch mm Inch lbs.
500 19.6 12 1/2” 3.0
1000Volt
Large Capacity Cable Cutter,
With Insulated Handle Insulation According
to EN/IEC 60900, ASTM F-1505 & CSA
Specification, Up to 1000 Volt. Individually
Tested. Easy cutting blades, dropped forged, oil
hardened. Cuts cable diameters up to 50mm.
Not to be used on steel rods.
Item OAL OAL Capacity
No. mm Inch mm Inch lbs.
800 31.5 50 2” 8.0
1000Volt
Insulated Cable Cutters
For cutting solid aluminum
& copper conductors
For cutting multi strand aluminum
& copper cables
31.5”
End Cutters, With Insulated
Handle. Insulation According to EN/IEC
60900, DIN ISO 8976, ASTM F-1505 & CSA
Specification. Individually Tested. Blade
alloyed tool steel. Induction hardened.
Item OAL OAL Capacity
No. mm Inch mm lbs.
250 10 7/8” 1.1
1000Volt
For cutting solid aluminum,
copper & medium hard wires
12853
12853
128
12858
12859
29012
29012
12326
12326
19767
19767
29240
29240
11950
11950
40800
40800
29250
29250
pkg.
1
pkg.
1
pkg.
1
pkg.
1
www.wihatools.com
14
Meets EN/IEC Insulation Standards
1000V
10,000 Volt tested 1000Volt rated
Slip guards at tips
for user safety
Two layer high
contrast insulated
coatings
Carbon steel with
chrome nickel plated
Insulated Serrated Straight
Fine Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
130 5.0 .06 1
1000Volt
Insulated Serrated Straight
Blunt Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
130 5.0 .08 1
1000Volt
Insulated Serrated Straight
Blunt Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
145 6.0 .10 1
1000Volt
Insulated Serrated Straight
Blunt Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
200 8.0 .18 1
1000Volt
Insulated Serrated Angled
Fine Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
145 6.0 .08 1
1000Volt
Insulated Serrated Angled
Blunt Tip Tweezers, IEC/EN 60900 & CSA
Standards, 10,000 Volt Tested
Item OAL OAL
No. mm Inch lbs. pkg.
200 8.0 .16 1
1000Volt
Wiha Insulated Serrated Tweezers
Wiha Insulated Ratcheting
Cable Cutters
High Voltage Double-Insulated
Ratcheting Cable Cutters High leverage
ratchet cable cutter with shear type blades cuts
stranded and flexible copper and aluminum
cable. Not for use on steel. Features built in
safety release in all cutting positions, and
high-visibility comfort grip handles.
Item OAL OAL up to Inch
No. mm Inch MCM Dia. Cap.
250 10.0” 500 1.25” 32ml
280 11.0” 750 2.0” 52ml
1000Volt
Insulated ACSR Ratcheting
Cable Cutter Replaceable tool steel cutting
blades are securely mounted for accurate
cutting. Handles lock in closed position for easier
storage. High leverage ratchet mechanism for
best cutting performance.
Item OAL OAL up to Inch
No. mm Inch MCM Dia. Cap.
353 13.9 477 1.25” 32ml
1000Volt
Each tool individually tested to 10,000 Volts &
certified to 1000 Volt ac or 1500 Volt dc
75205
75205
75210
75210
75215
75215
75220
75220
75302
75302
75304
75304
119
11960
11975
11980
11980
lbs.
1.6
2.0
lbs.
3.42
Toll Free: (800) 494-6104
15
Inch T-handle, With Wiha-Molded Handle. Blade CVM steel, hardened. Insulation
molded directly onto blade. Wiha-SoftFinish® handle, multi-component.
Item
No. Inch Inch Inch mm lbs. pkg.
5/32 5.9 6.9 176 .09 10
3/16 5.9 6.9 176 .15 10
7/32 5.9 6.9 176 .19 10
1/4 5.9 7.1 176 .20 10
5/16 5.9 7.1 176 .26 10
3/8 5.9 7.1 176 .44 10
Wiha Insulated T-handle Hex Drivers
1000Volt
Metric T-handle, With Wiha-Molded Handle. Blade CVM steel, hardened. Insulation
molded directly onto blade. Wiha-SoftFinish® handle, multi-component.
Item
No. mm mm Inch mm Inch lbs. pkg.
4.0 150 5.9 176 6.9 .09 10
5.0 150 5.9 182 7.1 .15 10
6.0 150 5.9 182 7.1 .18 10
8.0 150 5.9 182 7.1 .26 10
10.0 150 5.9 191 7.5 .46 10
6 Piece Inch T-handle Hex Set
Item Inch:
No. 5/32, 3/16, 7/32, lbs.
1/4, 5/16, 3/8” 1.66
1000Volt
1000Volt
Blade
CVM tool steel,
hardened to
average 58/60RC
Responds to OSHA’s
use specification
29 CFR1910
Insulation
Molded directly onto blade
for permanent bonding
Insulation Test Standards:
Insulation according to EN/IEC 60900, ASTM F-1505,
VDE 0682/part 201, DIN 7437, NFPA70E & CSA specification
Each tool individually tested
to 10,000 Volts & certified to
1000 Volt ac or 1500 Volt dc
5 Piece Metric T-handle Hex Set
Item Metric:
No. 4.0, 5.0, 6.0, lbs.
8.0, 10.0mm 1.20
Wiha Insulated T-handle Metric Nut Drivers
Metric T-handle Nut Drivers, With Wiha-Molded Handle. Insulation According to
ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA,
up to 1000Volt. Individually Tested. Blade CVM steel, hardened. Insulation molded directly
onto blade. Wiha-SoftFinish® handle, multi-component.
Item
No. mm mm Inch mm Inch lbs. pkg.
8.0 200 7.9 232 9.1 .15 5
10.0 230 9.0 262 10.3 .18 5
13.0 230 9.0 262 10.3 .26 5
17.0 230 9.0 268 10.6 .46 5
1000Volt
1000Volt
334
33481
33482
33483
33485
33486
33487
334
33441
33443
33445
33447
33449
33490
33490
33478
33478
336
33632
33634
33637
33641
www.wihatools.com
16
Wiha Insulated TorqueControl & SlimLine Tool Sets
8 Piece Insulated TorqueControl
Set With Slotted & Phillips SlimLine Blades
Set includes Insulated multi-component
adjustable TorqueVario-S handle, 5 SlimLine
blades, SlimLine blade holder & Torque
adjustment tool.
Item No. Slotted: 3.0, 4.0, 5.5mm
Phillips: #1, 2
28726-Handle Range 10-50 Inch/lbs.
lbs. .87
With Certificate
of Calibration
16 Piece Insulated
TorqueControl Set With SlimLine Blades
Certified to EN ISO 6798, BS EN 26789,
ASME B107.14M. Set includes Insulated multi-
component adjustable TorqueVario-S handle,
13 SlimLine blades, SlimLine blade holder &
Torque adjustment tool.
Item No.
SlimLine Slotted: 4.0, 5.5, 6.5mm
SlimLine Phillips: #1, 2
SlimLine Terminal Xeno: #1, 2
SlimLine : T8, T10, T15, T20
SlimLine Square: #1, 2
28727 - Handle Range 18-62 Inch/lbs.
SlimLine Blade Holder
lbs. 1.27
With Certificate of Calibration
1000Volt
1000Volt
In Roll-up
Pouch
In Roll-up
Pouch
Certified to EN ISO 6798, BS EN 26789,
ASME B107.14M Specifications
Insulated Torque Ratchet
Wrenches, 1/4, 3/8, 1/2” Drives Insulated
to EN/IEC 60900:2004, ASTM F1505, CSA
Standards Visible reading scale for easy
reading and adjustment. Locking endcap
Torque adjuster for easy adjustment. Accuracy
+/- 10%. Dual scale reading Ft. lbs. / Nm.
Item OAL OAL
No. Inch mm Inch Nm
1/4” 210 8.25 5-25
3/8” 370 14.5 5-50
1/2” 530 21.0 40-220
1000Volt
Wiha Insulated Torque
Ratchet Wrenches
#30138
#30114
1000Volt
16 Pc. Insulated 3/8” Drive
Ratcheting Torque Wrench & Socket Set -
Inch
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Inch 3/8” Drive Sockets:
1/4, 9/32, 5/16, 11/32, 3/8, 7/16
1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8”
lbs. 3/8” x 125mm Extension Bar
8.80 3/8” x 250mm Extension Bar
3/8” Drive Ratcheting Torque
Wrench - 5-50 Nm
*Sockets must be used with insulated ratchets & extensions
16 Pc. Insulated 3/8” Drive
Ratcheting Torque Wrench & Socket Set -
Metric
CV steel, forged, oil-hardened
sockets. Insulated to EN/IEC 60900.
Item No. Metric 3/8” Drive Sockets:
8, 9, 10, 11, 12, 13, 14, 15, 16,
17, 18, 19, 20mm
lbs. 3/8” x 125mm Extension Bar
8.80 3/8” x 250mm Extension Bar
3/8” Drive Ratcheting Torque
Wrench - 5-50 Nm
*Sockets must be used with insulated ratchets & extensions
1000Volt
Wiha Insulated Torque Ratchet Wrench Sets
Insulated TorqueVario-S, With
Window Scale Insulation up to 1000Volt
EN/IEC, EN ISO, BS EN, ASME & CSA,
+/- 6% Accuracy. Ergonomic multi-component
handle, light & compact. Handle sizes
proportioned to optimize torque range. Audible
& perceptible click when torque setting has
been attained. In Plastic Tube Holder
Item Range
No. Inch lbs. Increments mm
5 - 18 .5 In/lbs 126-131
10 - 50 2 In/lbs 133-138
18 - 62 2 In/lbs 137-142
Each TorqueVario handle has unique serial
number & certificate of calibration
Wiha Insulated
TorqueControl Tools
* Includes
Certificate
* Includes
SlimLine blade
holder #28350
Item Range
No. Nm mm lbs. pkg.
0.5 - 2.0 131 .64 1
1.0 - 5.0 138 .56 1
2.0 - 7.0 142 .84 1
Insulated TorqueVario-S
Handle - In Newton Meter Scale
* Requires
SlimLine
Blades
1000Volt
28791
28791
28792
28792
301
30114
30138
30152
30190 30192
30190 30192
28750
28751
28752
28740
28741
28742
287
287
lbs.
1.02
2.72
3.64
pkg.
1
1
1
lbs. pkg.
.56 1
.74 1
.84 1
Toll Free: (800) 494-6104
17
Insulated TorqueVario-S, With
Window Scale Insulation up to 1000Volt.
EN/IEC 60900 EN ISO 6798, BS EN 26789,
ASME B107.14M &CSA, +/- 6% Accuracy.
Ergonomic multi-component handle, light
& compact. Handle sizes proportioned to
optimize torque range. Audible & perceptible
click when torque setting has been attained.
Item Range
No. Inch lbs. Increments mm
5 - 18 .5 In/lbs 126-131
10 - 50 2 In/lbs 133-138
18 - 62 2 In/lbs 137-142
Each TorqueVario handle has unique serial
number & certificate of calibration
Wiha Insulated
TorqueControl Tools
Includes Certificate
1000Volt
*Requires SlimLine blade holder #28350
Item Range
No. Nm mm lbs. pkg.
0.5 - 2.0 131 .45 1
1.0 - 5.0 138 .45 1
2.0 - 7.0 142 .72 1
Insulated TorqueVario-S Handle -
In Newton Meter Scale
Insulated SlimLine Torque
Blade Holder Chrome-vanadium-molybdenum
steel. Through hardened black finish. ClicFix
quick release holder securely locks bits.
Item OAL OAL
No. mm mm Inch lbs. pkg.
6.0 170 6.75 .06 1
1000Volt
Insulated Easy-TorqueControl
Adapters Ideal for torque sensitive
terminations. For use with SlimLine blades.
Repeatable accuracy to +/- 10%
Item OAL OAL
No. Nm In/lbs mm Inch lbs. pkg.
0.8 7.0 60 2.38 .13 1
2.0 17.7 60 2.38 .13 1
2.5 23.1 60 2.38 .13 1
2.8 24.7 60 2.38 .13 1
4.0 35.4 60 2.38 .13 1
1000Volt
Wiha Insulated Pop-Up
SlimLine Sets
Insulated Pop-Up “Apprentice”
Blade Holder Set With
SlimLine
Blades
Insulated cushion grip multi-component handle.
Friction hold bit holder holds SlimLine Blades
securely. Convenient rotating cap.
Set includes the following blades:
Slotted: 3.0, 4.0, 5.5, 6.5mm
Phillips: #1, #2
lbs. .38
Blades High
quality CV steel,
through-hardened
1000Volt Rated
10,000 Volt Tested
Insulated Pop-Up “Residental”
Blade Holder Set With
SlimLine
Blades
Set includes the following blades:
Slotted: 3.0, 4.0mm
Phillips: #1, #2
Square: #1, #2
lbs. .38
Insulated Pop-Up “MRO” Blade
Holder Set With
SlimLine
Blades
Set includes the following blades:
Slotted: 3.0, 4.0mm
Phillips: #1, #2
Terminal Xeno: #1, #2
lbs. .38
1000Volt
1000Volt
Friction hold blade holder
securely holds blades in
place for precise fastening
Certified to VDE, EN
ISO, BS EN, ASME
specifications
Each SlimLine bit can be
taken in and out of the
holder easily and
conveniently
Wiha Cushion Grip Stubby
SlimLine Blade Holder & Set
SlimLine Stubby Blade Holder,
With Wiha-SoftFinish® Handle. Insulation
According to VDE, ASTM, EN/IEC, NFPA70E
& CSA, up to 1000 Volt. Wiha-SoftFinish®
handle, multi-component, cushion grip.
Item
No. Size mm Inch lbs. pkg.
1/4” 57 2.2 .11 1
1000Volt
1000Volt
20 Piece Insulated SlimLine Blade
Set High quality CV steel, through hardened.
Friction hold, stubby cushion grip handle.
In zipper case.
Item No.
Slotted: 3.0, 3.5, 4.0, 5.5mm
Phillips: #1, #2
lbs. Xeno SL/PH: #1, #2
.85 Xeno SL/PZ: #1, #2
: T8, T10, T15, T20
Square: #1, #2
Hex Metric: 3.0, 4.0, 5.0mm
SlimLine Stubby Blade Holder
Meets VDE, EN/IEC, ASTM,
CSA, NFPA specifications
“MRO”
“Residental”
“Apprentice”
287
28724
28726
28727
28734
28736
28738
287
28350
28350
283
28366
28367
28368
28369
28371
28393
28393
28394
28394
28395
28395
28302
28302
28396
28396
lbs. pkg.
.43 1
.40 1
.69 1
www.wihatools.com
18
1000Volt
8 Piece Insulated SlimLine Blade
Set High quality CV steel, through hardened.
Cushion grip. Friction hold blade holder, holds
blades securely. Up to 33% narrower insulation
diameter then standard insulated tools.
In roll up pouch
Item No. Slotted: 4.0, 6.5
Phillips: #1, #2
Xeno SL/PH: #2
lbs. .45 : T15, T20
28301 - SlimLine Blade Holder
15 Piece Insulated SlimLine
Blade Set High quality CV steel, through
hardened. Cushion grip. Friction hold blade
holder, holds blades securely. Up to 33%
narrower insulation diameter then standard
insulated tools. In roll up pouch
Item No. Slotted: 3.0, 4.0, 5.5, 6.5
Phillips: #1, #2
Xeno SL/PH: #1, #2
lbs. : T8, T10, T15, T20
.56 Square: #1, #2
28301 - SlimLine Blade Holder
1000Volt
1000Volt
12 Piece Insulated SlimLine
Blade Set High quality CV steel, through
hardened. Cushion grip. Friction hold blade
holder, holds blades securely. SlimLine blades
have up to 33% narrower insulation diameter
then standard insulated tools. In roll up pouch
Item No. Slotted: 3.0, 5.5mm
Phillips: #2
Xeno SL/PH: #1, #2
lbs. Square: #1, #2
.52 : T8, T10, T15, T20
28301 - SlimLine Blade Holder
19 Piece Insulated SlimLine
Blade Set High quality CV steel, through
hardened. Cushion grip. Friction hold blade
holder, holds blades securely. In zipper case
Item No.
Slotted: 3.0, 4.0, 5.5mm
Phillips: #1, #2
lbs. Xeno SL/PH: #1, #2
.64 Xeno SL/PZ: #1, 2
: T8, T10, T15, T20
Square: #1, 2
Hex Metric: 3.0, 4.0, 5.0mm
28301 - SlimLine Blade Holder
1000Volt
Wiha Insulated SlimLine Blade Sets
SlimLine Blade Holder, With
Wiha-SoftFinish® Handle Insulation
According to VDE, ASTM F-1505 and EN/
IEC 60900, NFPA70E & CSA, up to 1000
Volt. Chrome-vanadium steel, through-
hardened. Insulation molded directly onto
blade. Friction hold blade holder, holds blades
securely. Wiha-SoftFinish® handle,
multi-component, cushion grip.
Item
No. Size mm Inch mm Inch
1/4” 50 2.0 160 6.3
1000Volt
33%
Narrower
Insulation
Diameter
Slim Diameter
Wiha Cushion Grip
SlimLine Blade Holder
30 Piece Insulated SlimLine Blade
Set High quality CV steel, through hardened.
Friction hold blade holder, holds blades
securely. In belt wallet storage pouch.
Item No. Slotted: 2.5, 3.0, 3.5, 4.0, 5.5, 6.5mm
Phillips: #1, #2
Pozidriv®: #1, #2
lbs. Xeno SL/PH: #1, #2
1.20 Xeno SL/PZ: #1, #2
: T8, T9, T10, T15, T20, T25
Square: #1, #2
Hex Metric: 1.5, 2.0, 2.5, 3.0,
4.0, 5.0, 6.0mm
28301 - SlimLine Blade Holder
1000Volt
SlimLine Stubby Blade Holder,
With Wiha-SoftFinish® Handle. Insulation
According to VDE, ASTM, EN/IEC, NFPA70E
& CSA, up to 1000 Volt. Wiha-SoftFinish®
handle, multi-component, cushion grip.
Item
No. Size mm Inch lbs. pkg.
1/4” 57 2.2 .11 1
1000Volt
SlimLine Blade Holder, With
Wiha-SoftFinish® Handle. Insulation
According to VDE, ASTM, EN/IEC, NFPA70E
& CSA, up to 1000 Volt. Wiha-SoftFinish®
handle, multi-component, cushion grip.
Item
No. Size mm Inch lbs. pkg.
1/4” 114 4.5 .21 1
1000Volt
28391
28391
28390
28390
28392
28392
28398
28398
28301
28301
28399
28399
28302
28302
28304
28304
lbs.
.15
Toll Free: (800) 494-6104
19
Wiha Insulated SlimLine Blades
Insulated Slotted SlimLine Blades
SlimLine blades have up to 33% narrower
insulation diameter then standard insulated tools.
Item Slim Max Inch/
No. mm Inch Dia. Nm lbs.
2.5 3/32 4.0 0.4 3.5
3.0 1/8 4.0 0.6 5.3
3.5 9/64 4.0 2.5 22.1
4.0 5/32 4.0 2.5 22.1
5.5 7/32 6.0 3.8 33.6
6.5 1/4 6.0 5.5 48.6
Insulated Phillips SlimLine Blades
SlimLine blades have up to 33% narrower
insulation diameter then standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1 4.0 3.8 33.7
2 6.0 5.5 48.8
Insulation Test Standards:
Insulation according to EN/IEC 60900,
ASTM F-1505, VDE 0682/part 201,
DIN 7437, NFPA70E & CSA specification
Wiha SlimTECHNOLOGY
Achieves blade diameters
up to 33% narrower utilizing
integrated insulation
Integrated Slim
Insulation molded
directly onto blade
High quality CV
steel, through-
hardened
1000 Volt Rated
Insulation does
not exceed screw
head diameter
10,000 Volt Tested
Insulated Pozidriv® SlimLine Blades
SlimLine blades have up to 33% narrower
insulation diameter then standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1 4.0 3.8 33.7
2 6.0 5.5 48.8
Insulated Xeno Slotted/Phillips
SlimLine Blades Up to 33% narrower insulation
diameter then standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1 4.0 3.8 33.6
2 6.0 5.5 48.7
Insulated SlimLine Blades
Up to 33% narrower insulation diameter then
standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
T8 4.0 1.3 11.5
T9 4.0 1.3 11.5
T10 4.0 3.8 33.6
T15 6.0 5.5 48.7
T20 6.0 5.5 48.7
T25 6.0 5.5 48.7
Insulated Square SlimLine Blades
Up to 33% narrower insulation diameter then
standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1 4.0 3.8 33.6
2 6.0 5.5 48.7
Insulated Xeno Slotted/Pozidriv®
SlimLine Blades Up to 33% narrower
insulation diameter then standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1 4.0 3.8 33.6
2 6.0 5.5 48.7
Insulated Hex Metric SlimLine
Blades Up to 33% narrower insulation
diameter then standard insulated tools.
Item Slim Max Inch/
No. Size Dia. Nm lbs.
1.5 4.0 0.9 7.9
2.0 4.0 1.8 15.9
2.5 4.0 3.8 33.6
3.0 4.0 5.5 48.7
4.0 6.0 5.5 48.7
5.0 6.0 5.5 48.7
6.0 6.0 5.5 48.7
283
28307
28308
28310
28309
28312
28315
283
28317
28319
28330
28331
283
283
28327
28329
283
28339
28344
28340
28341
28342
28343
283
28346
28347
283
28320
28321
28332
28333
28334
28335
28336
28337
28338
283
lbs. Pkg.
.02 1
.02 1
.02 1
.02 1
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
.02 1
.02 1
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
lbs. Pkg.
.02 1
.02 1
.02 1
.02 1
.02 1
.02 1
.02 1
www.wihatools.com
20
Wiha Insulated SlimLine Screwdrivers
Insulated Slotted SlimLine
Screwdrivers Insulation According to
ASTM F-1505, New VDE Specification
0682/part 201 and EN/IEC 60900, NFPA70E
& CSA, up to 1000 Volt. Individually
Tested to 10,000Volts. High quality CV
steel, through hardened. SlimLine blades have
up to 33% narrower insulation diameter then
standard insulated tools. Wiha-SoftFinish®
handle, multi-component, cushion grip.
Item Slim
No. mm Inch Dia. mm mm
3.5 9/64 3.5 100 204
4.0 5/32 4.0 100 211
4.5 3/16 4.5 125 211
5.5 7/32 5.5 125 243
6.5 1/4 6.5 150 268
Insulated Phillips SlimLine
Screwdrivers Insulation According to
ASTM F-1505, New VDE Specification
0682/part 201 and EN/IEC 60900, NFPA70E
& CSA, up to 1000 Volt. Individually
Tested to 10,000Volts.
Item Slim
No. Size Dia. mm mm
1 4.5 80 204
2 6.0 100 211
Insulated Xeno SlimLine Drivers
For Terminal Screws Insulation According
to ASTM F-1505, New VDE Specification
0682/part 201 and EN/IEC 60900, NFPA70E
& CSA, up to 1000 Volt. Individually
Tested to 10,000Volts.
Item Slim
No. Size Dia. mm mm
1 4.5 80 191
2 6.0 100 218
Insulated Square SlimLine Drivers
Insulation According to ASTM F-1505, New
VDE Specification 0682/part 201 and EN/
IEC 60900, NFPA70E & CSA, up to 1000
Volt. Individually Tested to 10,000Volts.
Item Slim
No. Size Dia. mm mm
1 4.0 100 218
2 4.5 125 243
1.4”
1.4”
1.4”
1.4”
Insulation Test Standards:
Insulation according to EN/IEC 60900,
ASTM F-1505, VDE 0682/part 201,
DIN 7437, NFPA70E & CSA specification
Ideal for jobs
where access
is limited
Integrated Slim
Insulation molded
directly onto blade
Wiha
SlimTECHNOLOGY
Achieves blade
diameters up to
33% narrower
utilizing integrated
insulation
1000 Volt Rated
10,000 Volt Tested
Insulated PicoFinish
Precision Screwdrivers
Insulated Slotted PicoFinish
Screwdrivers. Individually Tested Protective
Insulation 1000Volt AC, VDE & GS Tested.
Item
No. mm Inch mm mm lbs.
1.5 .06 40 154 .05
2.0 .08 40 154 .07
2.5 .10 60 160 .07
3.0 .12 60 160 .08
3.5 .14 60 160 .08
Insulated Phillips PicoFinish
Screwdrivers. Individually Tested Protective
Insulation 1000Volt AC, VDE & GS Tested.
Item
No. Size mm mm lbs.
00 40 154 .05
0 60 160 .07
1 60 160 .08
8 Piece Slotted & Phillips
PicoFinish Set High quality CV steel, through
hardened, black finish
Item No. Slotted: 1.5, 2.0, 2.5, 3.0, 3.5 lbs.
Phillips: #00, #0, #1 .35
5 Piece Slotted & Phillips
PicoFinish Set High quality CV steel, through
hardened, black finish
Item No. Slotted: 1.5, 2.5, 3.5 lbs.
Phillips: #0, #1 .26
Individually Tested Protective
Insulation 1000Volt AC,
VDE & GS Tested
1000Volt
1000Volt
1000Volt
1000Volt
Rotating cap
for precise
turning and
control with
fingertip
Insulated Security SlimLine
Drivers Insulation According to ASTM, New
VDE Specification 0682/part 201 and EN/
IEC 60900, NFPA70E & CSA, up to 1000
Volt. Individually Tested to 10,000Volts.
Item
No. Size mm mm
T10s 100 204
T15s 100 211
T20s 100 211
T25s 125 243
T27s 125 243
T30s 125 243
T40s 150 268
1.4”
1000Volt
1000Volt
1000Volt
1000Volt
320
32046
32049
32052
32055
32058
321
32145
32146
307
30746
30747
358
35844
35845
32000
32001
32002
32003
32004
32106
32107
32108
32088
32085
320
321
32088
32085
325
32512
32513
32514
32515
32517
32518
32519
pkg.
1
1
1
1
1
pkg.
1
1
1
lbs. Pkg.
.07 1
.12 1
.14 1
.21 1
.25 1
lbs. Pkg.
.12 1
.21 1
lbs. Pkg.
.12 1
.19 1
lbs. Pkg.
.12 1
.21 1
lbs. Pkg.
.08 1
.12 1
.12 1
.18 1
.21 1
.21 1
.26 1
Toll Free: (800) 494-6104
21
Wiha Insulated SlimLine Screwdriver Sets
6 Piece Insulated SlimLine
Slotted, Phillips & Square Screwdrivers.
Insulation According to ASTM F-1505,
New VDE Specification 0682/part 201 and
EN/IEC 60900, NFPA70E & CSA, up
to 1000 Volt. Individually Tested to
10,000Volts. High quality CV steel, through
hardened. SlimLine blades have up to 33%
narrower insulation diameter then standard
insulated tools. Wiha-SoftFinish® handle, multi-
component, cushion grip.
Item Slotted: 4.5, 6.5mm
No. Phillips: #1, #2 lbs.
Square: #1, #2 1.15
1000Volt
11 Piece Insulated SlimLine
Slotted, Phillips, Xeno & Square
Screwdrivers. Insulation According to
ASTM F-1505, New VDE Specification
0682/part 201 and EN/IEC 60900, NFPA70E
& CSA, up to 1000 Volt. Individually
Tested to 10,000Volts. High quality CV steel,
through hardened. SlimLine blades have up
to 33% narrower insulation diameter then
standard insulated tools. Wiha-SoftFinish®
handle, multi-component, cushion grip.
Item No. Slotted: 3.5, 4.0, 4.5, 5.5, 6.5mm
Phillips: #1, 2
Square: #1, 2
lbs. 1.75 Xeno: #1, 2
1000Volt
8 Piece Insulated SlimLine
Slotted, Phillips & Square Screwdrivers.
Insulation According to ASTM F-1505, New
VDE Specification 0682/part 201 and EN/
IEC 60900, NFPA70E & CSA, up to 1000
Volt. Individually Tested to 10,000Volts.
High quality CV steel, through hardened.
SlimLine blades have up to 33% narrower
insulation diameter then standard insulated
tools. Wiha-SoftFinish® handle, multi-
component, cushion grip.
Item No. Slotted: 3.5, 4.0, 4.5, 5.5mm
Phillips: #1, 2
Square: #1, 2
lbs. 1.18
1000Volt
2 Pc. Insulated SlimLine Slotted
& Phillips Screwdrivers. Meets ASTM,
VDE, EN/IEC, NFPA70E & CSA Specs,
Individually Tested to 10,000Volts. High
quality CV steel, through hardened. SlimLine
blades have up to 33% narrower insulation
diameter then standard insulated tools.
Item No. Slotted: 4.5x125mm
Phillips: #2x100mm
lbs. .37
1000Volt
Wiha Slim TECHNOLOGY
Achieves blade diameters up to 33%
narrower utilizing Wiha integrated insulation
2 Pc. Insulated SlimLine Terminal
Block Xeno Slotted/Phillips Screwdrivers.
Meets ASTM, VDE, EN/IEC, NFPA70E & CSA
Specs, Tested to 10,000Volts. High quality
CV steel, through hardened. SlimLine blades
have up to 33% narrower insulation diameter
then standard insulated tools.
Item No. Xeno: #1x80mm
Xeno: #2x100mm
lbs. .34
1000Volt
Slotted/Phillips
6 Pc. Insulated SlimLine
Security Screwdrivers. Insulation
According to ASTM F-1505, New VDE
Specification 0682/part 201 and EN/IEC
60900, NFPA70E & CSA, up to 1000 Volt.
Individually Tested to 10,000Volts. High
quality CV steel, through hardened. SlimLine
blades have up to 33% narrower insulation
diameter then standard insulated tools.
Item No. Security : T10s, T15s,
T20s, T25s, T27s, T30s
lbs. 1.18
1000Volt
1000Volt
30 Pc. Insulated SlimLine Slotted
& Phillips Screwdriver Display. Meets
ASTM, VDE, EN/IEC, NFPA70E & CSA
Specs, Tested to 10,000Volts. SlimLine
blades have up to 33% narrower insulation
diameter then standard insulated tools. High
quality CV steel, through hardened.
Item 6 of each:
No. Slotted: 3.5, 4.5, 5.5mm
Phillips: #1, #2
32198
32198
32197
32197
32196
32196
32189
32189
30770
30770
32596
32596
32079
32079
www.wihatools.com
22
Blade
CVM tool steel, hardened
to average 58/60RC
Responds to OSHA’s use
specification 29 CFR1910
Insulation
Molded directly onto the
blade for permanent bonding
SoftFinish® handle Solid molded core
with soft outer cushion grip.
40% more torque than
conventional handles
Phillips Screwdriver, With Wiha-SoftFinish® Handle. Insulation According to ASTM
F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to
1000 Volt. Individually Tested.
Item
No. Size mm Inch mm Inch lbs. pkg.
0 60 2.4 164 6.5 .06 10
1 80 3.0 191 7.5 .12 10
2 100 4.0 218 8.6 .20 10
3 150 6.0 268 10.6 .34 10
4 200 8.0 318 12.5 .39 10
Insulation Test Standards:
Insulation according to EN/IEC 60900,
ASTM F-1505, New VDE 0682/part 201,
DIN 7437, NFPA70E & CSA
Each tool individually tested to 10,000 Volts &
certified to 1000 Volt ac or 1500 Volt dc
1000V
Slotted Screwdriver, With Wiha-SoftFinish® Handle. Insulation According to
ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA,
up to 1000 Volt. Individually Tested.
Item
No. mm Inch Inch mm Inch mm Inch lbs. pkg.
2.0 .078 5/64 60 3.0 164 6.5 .05 10
2.5 .098 3/32 75 3.0 179 7.1 .06 10
3.0 .118 1/8 100 4.0 204 8.0 .07 10
3.5 .139 9/64 100 4.0 204 8.0 .07 10
4.0 .157 5/32 100 4.0 211 8.3 .12 10
4.5 .177 3/16 100 4.0 211 8.3 .12 10
4.5 .177 3/16 125 5.0 236 9.3 .12 10
4.5 .177 3/16 150 6.0 261 10.2 .14 10
4.5 .177 3/16 175 7.0 286 11.2 .13 10
4.5 .177 3/16 200 8.0 311 12.3 .15 10
5.5 .216 7/32 125 5.0 243 9.5 .15 10
5.5 .216 7/32 175 7.0 293 11.5 .21 10
6.0 .236 15/64 150 6.0 268 10.6 .21 10
6.5 .255 1/4 150 6.0 268 10.6 .21 10
8.0 .315 5/16 175 7.0 299 11.8 .34 10
10.0 .393 3/8 200 8.0 318 12.5 .39 10
4 Piece Slotted & Phillips Set
Item No. Slotted: 3.5, 4.5
Phillips: #1, 2
lbs. .76
#32892
page 32
Wiha Insulated Screwdrivers with SoftFinish® Cushion Grip Handle
1000Volt
1000Volt
2 Piece Slotted & Phillips Set
Item Slotted: 5.5
No. Phillips: #2
lbs. .50
1000Volt
1000Volt
2 Piece Slotted & Phillips Set
Item Slotted: 6.0
No. Phillips: #2
lbs. .50
1000Volt
320
32005
32010
32012
32015
32017
32023
32024
32027
32025
32028
32031
32026
32034
32039
32042
32045
32090
32090
321
32100
32101
32102
32103
32104
32105
32105
33532
33532
Toll Free: (800) 494-6104
23
5 Piece Slotted & Phillips Set
Item Slotted: 3.0, 4.5, 6.5
No. Phillips: #1, 2
lbs. 1.31
6 Piece Slotted & Phillips Set
Item No. Slotted: 3.5, 4.5, 6.5
Phillips: #1, 2, 3
lbs. 1.38
1000Volt
7 Piece Slotted & Phillips Set
Item No.
Slotted: 2.0, 2.5, 3.0, 3.5, 4.0
Phillips: #0, 1
lbs. .92
1000Volt
13 Piece Slotted & Phillips Set
Item No. Slotted: 2.0, 2.5, 3.0, 3.5, 4.5,
5.5, 6.5, 8.0, 10.0mm
Phillips: #0, 1, 2, 3
lbs. 2.3
10 Piece Slotted & Phillips Set
Item No. Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 6.5
Phillips: #0, 1, 2, 3
lbs. 1.63
1000Volt
Wiha Insulated Screwdriver Sets
15 Piece Slotted, Phillips & Inch
Nut Drivers Set
Item No. Slotted: 2.0, 2.5, 3.0, 3.5,
4.5, 6.5, 8.0mm
Phillips: #1, 2, 3
lbs. Nut Drivers Inch: 1/4, 5/16,
5.9 3/8, 7/16, 1/2”
1000Volt
19 Piece Slotted, Phillips,
Square, Xeno Screwdriver Set
Insulated Screwdriver set in a light weight tool
box tray.
Item No. Slotted: 2.5, 3.0, 3.5, 4.0, 4.5,
5.5, 6.0, 6.5, 8.0, 10.0mm
Phillips: #0, #1, #2, #3
Square: #1, #2
lbs. Xeno Terminal: #1, #2
4.92 Cat. III Voltage Detector -
(Battery Operated)
1000Volt
Tool box
set in blow
molded tray
14 Piece Slot/Phil/Inch Nut
Drivers & Pliers/Cutters Set
Item No. Slotted: 3.0, 4.5, 6.5mm
Phillips: 1, 2
Nut Drivers Inch: 1/4, 5/16,
lbs. 11/32, 3/8, 1/2”
5.5 8.0” Combo Pliers,
6.3” Diagonal Cutters
6.3 & 8.0” Long Nose Pliers/Cutters
1000Volt
1000Volt
1000Volt
32091
32091
32092
32092
32188
32188
32094
32094
32093
32093
32190
32190
32095
32095
32192
32192
www.wihatools.com
24
6 Pc. Insulated Slotted, Phillips &
Square Screwdrivers
Item No. Slotted: 4.5, 6.5mm
Phillips: #1, 2 lbs.
Square: #1, 2 .83
Wiha Insulated Square Tip Screwdrivers
Square Tip Screwdriver, With
Wiha-SoftFinish® Handle Insulation
According to ASTM, VDE, EN/IEC, NFPA70E
and CSA, up to 1000 Volt. Individually
Tested. Blade high alloy CVM steel, hardened,
black finish.
Item
No. Size mm Inch mm Inch
1 100 4.0 210 8.2
2 150 6.0 268 10.5
1000Volt
1000Volt
6 Pc. Insulated Slotted, Phillips
& Square Screwdrivers
Item No. Slotted: 3.0, 5.5mm
Phillips: #1, 2 lbs.
Square: #1, 2 .83
Hex Metric Screwdriver, With Wiha-SoftFinish® Handle
Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC
60900, NFPA70E & CSA, up to 1000 Volt. Individually Tested Blade high alloy CVM
steel, hardened, black finish. Insulation molded directly onto blade. Wiha-SoftFinish® handle,
multi-component, cushion grip.
Item
No. Size mm Inch mm Inch lbs. pkg.
2.5 75 3.0 179 7.0 .06 10
3.0 75 3.0 179 7.0 .08 10
4.0 75 3.0 186 7.3 .12 10
5.0 75 3.0 186 7.3 .15 10
6.0 100 3.9 218 8.6 .24 10
8.0 100 3.9 218 8.6 .34 10
6 Piece Insulated Hex Metric
Screwdriver Set
Item No.
Hex Metric:
2.5, 3.0, 4.0, 5.0, 6.0, 8.0mm
lbs. 1.06
Wiha Insulated Hex Metric Screwdrivers
1000Volt
Wiha Insulated Screwdrivers
Screwdriver, With Wiha-SoftFinish® Handle
Insulation According to ASTM F-1505, New VDE Specification 0682/part 201 and EN/IEC
60900, NFPA70E and CSA, up to 1000 Volt. Individually Tested. Blade high alloy cvm
steel, hardened, black finish. Insulation molded directly onto blade.
Item
No. Size mm Inch mm Inch lbs. pkg.
T5 60 2.4 164 6.5 .06 10
T6 60 2.4 164 6.5 .06 10
T7 60 2.4 164 6.5 .06 10
T8 60 2.4 164 6.5 .06 10
T9 60 2.4 164 6.5 .06 10
T10 60 2.4 164 6.5 .06 10
T15 80 3.0 191 7.5 .12 10
T20 80 3.0 191 7.5 .12 10
T25 80 3.0 198 7.8 .17 10
T27 100 4.0 218 8.6 .20 10
T30 100 4.0 218 8.6 .20 10
T40 150 6.0 274 10.8 .30 10
T45 150 6.0 274 10.8 .35 10
1000Volt
1000Volt
6 Piece Set
Item No. TORX:
T8, T9, T10, T15, T20, T25
lbs. .83
1000Volt
10 Piece Set
Item No. TORX: T6, T7,
T8, T9, T10, T15, lbs.
T20, T25, T27, T30 1.2
1000Volt
1000Volt
323
32302
32303
32304
32305
32306
32308
32366
32366
358
35811
35812
35890
35890
35891
35891
325
32505
32511
32516
32521
32526
32531
32536
32541
32546
32551
32556
32561
32566
32590
32590
32592
32592
lbs. pkg.
.12 10
.19 10
Toll Free: (800) 494-6104
25
Wiha Insulated Screwdrivers
Combination Terminal Block Xeno
Screwdriver, With Wiha SoftFinish® Handle.
Insulation According to ASTM F-1505, VDE,
0682/part 201, EN/IEC 60900, NFPA70E &
CSA specification. Individually Tested.
Blade CVM steel, hardened, black finish.
Insulation molded directly onto blade. Wiha-
SoftFinish® handle, multi-component, cushion
grip. For combination Slotted/Phillips head
terminal screws.
Item
No. Size mm mm Inch
1 80 191 7.5
2 100 218 8.6
Combination Slotted/Phillips
Terminal Block Drivers
Insulated Terminal Block Xeno Screwdrivers
1000Volt
Combination Terminal Block Xeno
Screwdriver, With Wiha SoftFinish® Handle.
Insulation According to ASTM F-1505, VDE,
0682/part 201, EN/IEC 60900, NFPA70E &
CSA specification. Individually Tested.
Blade CVM steel, hardened, black finish.
Insulation molded directly onto blade. Wiha-
SoftFinish® handle, multi-component, cushion
grip. For combination Slotted/Pozidriv® head
terminal screws.
Item
No. Size mm mm Inch
1 80 191 7.5
2 100 218 8.6
Slotted/Phillips Slotted/Pozidriv®
Slotted/Phillips or
Slotted/Pozidriv®
Pozidriv® Screwdriver, With Wiha SoftFinish® Handle. Insulation According
to ASTM F-1505, VDE, 0682/part 201, EN/IEC 60900, NFPA70E & CSA specification.
Individually Tested.
Item
No. Size mm mm Inch lbs. pkg.
0 60 164 6.5 .11 10
1 80 191 7.5 .13 10
2 100 218 8.6 .23 10
3 150 267 10.5 .30 5
1000Volt
Wiha Insulated Pozidriv® Screwdrivers
30 Pc. Workstation Insulated
Screwdriver Set
Item No. Slotted: 3.5, 4.0, 4.5, 5.5, 6.5mm
Phillips: #1, #2, #3
Pozidriv®: #1, #2
lbs. Square: #1, #2
8.50 Xeno Terminal Slt/Ph: #1, #2
Hex Metric: 2.5, 3.0, 4.0, 5.0, 6.0mm
TORX®: T8, T10, T15, T20, T25, T30
PicoFinish Slotted: 1.5, 2.0, 2.5mm
PicoFinish Phillips: #00, #0
1000Volt
Workstation
Insulated screwdrivers
in a steel stand
Insulated Single-Pole
Voltage Detector
Insulated Single-Pole Voltage
Detector. 110-250Volts. Insulation According
To DIN 57860/6 And DIN VDE 0680-6, GS
Tested. Blade CVM steel, hardened, nickel-
plated. Insulation molded directly onto blade.
Amber LED light. 10,000Volt tested.
Item
No. mm mm mm Inch
3.0 65 145 5.7
1000Volt
Cat. III Voltage Detector -
Battery Operated
Battery Operated Voltage
Detector Tests 90-1000 Volts. Category III,
CE IEC 61010-1 With audible sound and light
warnings. Requires 2 AAA batteries.
Item
No. mm Inch lbs. pkg.
150 6.0 .13 1
1000Volt
Insulated Drivers &
Voltage Detector Sets
7 Pc. Slotted, Phillips, Square &
Voltage Detector Set
Item Slotted: 4.0, 5.5, 6.5mm
No. Phillips: #1, #2
Square: #2
Ins. Single Pole Voltage Detector
lbs. 1.36
1000Volt
9 Pc. Slotted, Phillips, Square &
Voltage Detector Set In Molded Carry Case
Item Slotted: 3.5, 4.0, 4.5, 5.5mm
No. Phillips: #1, #2
Xeno Slt/Ph: #2
Ins. Single Pole Voltage Detector
lbs. 1.81
32089
1000Volt
307
30700
30701
307
30711
30712
324
32400
32401
32402
32403
32199
32199
25511
25511
25500
25500
32087
32087
32089
lbs. pkg.
.13 10
.23 10
lbs. pkg.
.12 10
.21 10
lbs. pkg.
.04 1
www.wihatools.com
26
7 Pc. Nut Driver Set - Metric Sizes
Item Metric:
No. 5.0, 5.5, 6.0, 7.0, lbs.
8.0, 10.0, 13.0mm 2.05
7 Pc. Nut Driver Set - Inch Sizes
Item Inch:
No. 3/16, 7/32, 1/4, 5/16, lbs.
3/8, 7/16, 1/2” 2.24
5 Pc. Nut Driver Set - Metric Sizes
Item Metric:
No. 6.0, 7.0, 8.0, 9.0, 10.0mm lbs.
1.36
5 Pc. Nut Driver Set - Inch Sizes
Item Inch:
No. 7/32, 1/4, 5/16, lbs.
3/8, 1/2” 1.52
Metric Nut Drivers, With Wiha-SoftFinish® Handle Insulation According to ASTM
F-1505, New VDE Specification 0682/part 201 and EN/IEC 60900, NFPA70E & CSA, up to
1000 Volt. Individually Tested. Blade CVM steel, hardened. Insulation molded directly onto
blade. Deep drawn 1” socket. Wiha-SoftFinish® handle, multi-component.
Item
No. mm mm mm Inch lbs. pkg.
4.0 125 236 9.3 .15 10
5.0 125 236 9.3 .16 10
5.5 125 236 9.3 .16 10
6.0 125 236 9.3 .16 10
7.0 125 243 9.6 .25 10
8.0 125 243 9.6 .25 10
9.0 125 243 9.6 .25 10
10.0 125 243 9.6 .27 10
11.0 125 243 9.6 .37 10
12.0 125 243 9.6 .38 10
13.0 125 243 9.6 .39 10
14.0 125 243 9.6 .39 10
15.0 125 243 9.6 .40 10
16.0 125 243 9.6 .42 10
17.0 125 243 9.6 .44 10
Inch Nut Drivers, With Wiha-SoftFinish® Handle
Item
No. Inch Inch mm Inch lbs. pkg.
5/32 5.0 236 9.3 .15 10
3/16 5.0 236 9.3 .15 10
7/32 5.0 236 9.3 .16 10
1/4 5.0 243 9.6 .24 10
5/16 5.0 243 9.6 .25 10
11/32 5.0 242 9.6 .26 10
3/8 5.0 243 9.6 .26 10
7/16 5.0 243 9.6 .36 10
1/2 5.0 243 9.6 .39 10
9/16 5.0 243 9.6 .39 10
5/8 5.0 243 9.6 .41 10
Wiha Insulated Metric & Inch Nut Drivers
1000Volt
1000Volt
1000Volt
1000Volt
1000Volt
1000Volt
11 Pc. Nut Driver Set - Inch Sizes
Item Inch: 5/32, 3/16, 7/32, 1/4,
No. 5/16, 11/32, 3/8, 7/16, lbs.
1/2, 9/16, 5/8” 3.00
9 Pc. Nut Driver Set - Inch Sizes
Item Inch: 3/16, 1/4,
No. 5/16, 11/32, 3/8, lbs.
7/16, 1/2, 9/16, 5/8” 3.16
1000Volt
In
roll-up
pouch
322
32206
32209
32212
32215
32218
32221
32224
32227
32230
32233
32236
32238
32239
32240
32241
322
32255
32258
32261
32264
32267
32268
32270
32273
32276
32278
32280
32296
32296
32294
32294
32292
32292
32293
32293
32291
32291
32288
32288
Toll Free: (800) 494-6104
27
Multi-Bit Screwdrivers
“Six Tools In One”
Multi-Bit Screwdriver Sets
with Wiha Powerhandle,
cellulose-acetate,
impact resistant. Snap-lock rotatable cap.
Chambered bit holder equipped with transparent
selector & 6 bits. 1/4” Bit holder, stainless steel.
Shaft CVM steel, hardened, chrome-plated.
Packaged in clear blister package. Blade Length =
120mm (4.7”) Overall Length = 230mm (9”)
Insulated Slotted/Phillips Multi-
Bit Screwdriver
Set includes the following 1/4” bits:
Slotted: 5.5, 6.0mm
Phillips: #0, 1, 2, 3
lbs. .39
Insulated Slotted/Phillips/Square
Multi-Bit Screwdriver
Set includes the following 1/4” bits:
Slotted: 6.5, 8.0mm
Phillips: #1, 2
Square: #1, 2
lbs. .41
Insulated Bit Holder
Insulation meets EN/IEC 60900
Tested to 10,000 Volts
Magnetic Bit Holder, 1/4” Wiha
Powerhandle & insulated shaft
. Holds up to 6
bits. (Holder only)
lbs. .26
Wiha Insulated Pop-Up Insert Bit Sets
Insulated Pop-Up Bit Holder Set
With 1/4” Insert Bits
Insulated cushion grip multi-component handle.
Bit holder holds 1/4” Insert bits. Convenient
rotating cap.
Item Set includes the following bits:
No. Slotted: 4.5, 5.5, 6.0mm
Phillips: #0, 1, 2, 3
Square: #1, 2, 3
Pozidriv®: #1, 2, 3
lbs. .46
Blades High
quality CV steel,
through-hardened
1000Volt Rated
10,000 Volt Tested
Friction hold
bit holder
securely
holds bits in
place
Certified to VDE, EN
ISO, BS EN, ASME
specifications
Insulated Pop-Up Bit Holder Set
With 1/4” Insert Bits
Insulated cushion grip multi-component handle.
Bit holder holds 1/4” Insert bits. Convenient
rotating cap.
Item Set includes the following bits:
No. Slotted: 4.5, 5.5, 6.0mm
Phillips: #0, 1, 2, 3
Square: #1, 2, 3
: T15, T20, T25
lbs. .46
1000Volt
1000Volt
1000Volt
Tested to 10,000 Volts
Convenient rotating cap
WARNING!
Insulated Tools are intended to provide protection against accidental contact with charged energized
circuits. For maximum safety we recommend de-energizing all circuits whenever possible before
starting work on electrical apparatus or conductors. Always visually inspect insulation on tools before
use, do not use tools if insulation shows signs of wear or damage to the insulated areas of the tool.
Wear appropriate eye protection when using hand tools. Use NFPA70E certified insulated protective
outer wear when appropriate.
Use & Care Guide For Insulated Tools:
Store tools to minimize risk of damage to insulation, always wear approved eye protection, Inspect
insulation prior to each use of any insulated tool. Use insulated tools where the ambient temperature is
between -20 to +70O C. Have a qualified safety technician visually inspect insulation on tools annually
for safe use.
1000Volt
38006
38007
38025
38050
38050
38051
38051
www.wihatools.com
28
3 Piece Insulated Pliers/Cutters & Multi-Bit Set In Belt
Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA
standards. Pliers chrome finish for long lasting corrosion protection.
Soft grip ergo designed handle body, safety slip guard. Insulated
multi-bit screwdriver includes Slotted, Phillips & Square bits.
Item No. Pliers/Cutters & Multi-Bit Set
6.3” / 160mm Diagonal Cutters
8.0” / 200mm Long Nose Pliers
Set Includes Bit Holder & The Following Bits:
Slotted: 4.5, 6.5mm • Phillips: 1, 2 • Square: 1, 2
lbs. 1.67
1000Volt
5 Piece Insulated Pliers/Cutters & Screwdrivers In Belt
Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA
standards. Pliers chrome finish for long lasting corrosion protection.
Soft grip ergo designed handle body, safety slip guard. Insulated
cushion grip drivers, multi-component. Blade CVM tool steel, hardened.
Item No. Insulated Pliers/Cutters & Screwdrivers
6.3” / 160mm Diagonal Cutters
8.0” / 200mm Long Nose Pliers
Insulated SoftFinish® Screwdrivers:
Slotted: 3.0, 4.5mm • Phillips: 2
lbs. 1.77
3 Piece Insulated Pliers/Cutters
In Belt Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E
& CSA standards. Pliers chrome finish for long lasting corrosion
protection. Soft grip ergo designed handle body, safety slip guard.
Item No. Insulated Pliers & Cutters
6.3” / 160mm Diagonal Cutters
8.0” / 200mm Long Nose Pliers
8.0” / 200mm Combination Pliers
lbs. 2.12
1000Volt
1000Volt
Wiha Insulated Belt Pack Pouch Sets
5 Pc. Insulated Pliers/Cutters & SlimLine Screwdrivers
In Belt Pack Pouch Tools meet EN/IEC, ASTM, VDE, NFPA70E & CSA
standards. Pliers chrome finish for long lasting corrosion protection. Soft
grip ergo designed handle body, safety slip guard. Insulated cushion grip
drivers, multi-component. Blade CVM tool steel, hardened.
Item No. Insulated Pliers/Cutters & Screwdrivers
9.0” / 225mm Lineman’s Pliers
8.0” / 200mm Long Nose Pliers
Insulated SlimLine SoftFinish® Screwdrivers:
Slotted: 4.5, 6.5mm • Phillips: 2
lbs. 2.26
1000Volt
17 Pc. Insulated Pop-Up Bit Holder & Pliers/Cutters Set
High quality CV steel, through hardened. Cushion grip handle with
magnetic holder to securely hold bits. Pliers & Cutters additionally
induction hardened. Hard chrome finish for long lasting corrosion
protection. Two component Insulated soft grip handle. In belt pack pouch
Item No. Set Includes 1/4” Insert Bits:
Slotted: 4.5, 5.5, 6.0mm • Phillips: #0, 1, 2, 3
Square: #1, 2, 3 • : T15, T20, T25
lbs. 8.0”/200mm Long Nose Pliers
3.72 8.0”/200mm High Leverage Cutters
9.5”/245mm Lineman’s Pliers
17 Pc. Insulated Pop-Up Bit Holder & Industrial Pliers/
Cutters Set High quality CV steel, through hardened. Cushion grip
handle with magnetic holder to securely hold bits. Pliers & Cutters
drop-forged from special tool steel. Industrial Soft grip ergonomically
designed handle body. In belt pack pouch
Item No. Set Includes 1/4” Insert Bits:
Slotted: 4.5, 5.5, 6.0mm • Phillips: #0, 1, 2, 3
Square: #1, 2, 3 • : T15, T20, T25
lbs. 8.0”/200mm Long Nose Pliers
3.60 8.0”/200mm High Leverage Cutters
9.5”/245mm Lineman’s Pliers
Insulated
Industrial
Pliers &
Cutters
1000Volt
1000Volt
Chrome
Finish Pliers
& Cutters
32871
32871
32872
32872
32873
32873
32875
32875
32886
32886
32990
32990
Toll Free: (800) 494-6104
29
Use & Care Guide For Insulated Tools:
Store tools to minimize risk of damage to insulation, always wear approved
eye protection, Inspect insulation prior to each use of any insulated tool.
Use insulated tools where the ambient temperature is between -20 to +70O
C. Have a qualified safety technician visually inspect insulation on tools
annually for safe use.
80 PC. Insulated Master Electrician’s Tool Set In Rolling
Water Tight Traveling Tool Box - 10,000Volt Tested, 1000Volt Rated
Item# Set Includes: lbs. 33.9
6.3” Long Nose Pliers 6.3” Diagonal Cutters
8.0” Long Nose Pliers 8.0” High Leverage Cutters
6.3” Bent Nose Pliers 6.3” Cable Cutters
6.3” Long Flat Nose Pliers 6.3” Stripping Pliers
9.0” Combo Pliers/Crimpers 8.0” Adjustable Wrench
1000Volt
Insulated Slotted: 2.5, 3.0, 3.5,
4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm
Insulated Phillips: #0, 1, 2, 3
Insulated Xeno Slotted/Phillips
Terminal: #1, 2
Insulated Square: #1, 2
Insulated TORX: T6, T7, T8, T9,
T10, T15, T20, T25, T30
Insulated Cable Knife: 50mm
Insulated Folding Ruler In/MM
Insulated Inch Sockets: 1/2, 9/16,
5/8, 11/16, 3/4, 13/16, 7/8”
Insulated Metric Sockets:
13.0, 14.0, 15.0, 17.0, 19.0,
20.0, 22.0mm
Insulated Ratchet 3/8” Drive
Insulated 4.9” Extension 3/8” Dr.
Insulated Inch Nut Drivers:
7/32, 1/4, 5/16, 3/8, 7/16”
Insulated Metric Nut Drivers:
5.0, 5.5, 6.0, 7.0, 8.0,
10.0, 13.0mm
Insulated T-handle Inch Hex:
5/32, 3/16, 7/32, 1/4, 5/16, 3/8”
Insulated T-handle Metric Hex:
4.0, 5.0, 6.0, 8.0mm
Insulated L-key: 10mm
Insulated L-key: 1/2”
Cat. III Voltage Detector-
Battery Operated
All Tools In
Dedicated
Positions
For Quick
Storage
& Easy
Location
Tracking
Wiha Insulated Master Electrician’s Tools
Insulation Test Standards:
Insulation according to EN/IEC 60900, ASTM F-1505, New
VDE 0682/part 201, DIN 7437, NFPA70E & CSA
112 Pc. Insulated Master Electrician’s Tool Set In Rolling
Water Tight Traveling Tool Box - 10,000Volt Tested, 1000Volt Rated
Item# Set Includes: lbs. 51.3
6.3” Long Nose Pliers 6.3” Diagonal Cutters
8.0” Long Nose Pliers 8.0” High Leverage Cutters
6.3” Bent Nose Pliers 6.3” Cable Cutters
6.3” Long Flat Nose Pliers 6.3” Stripping Pliers
9.0” Combo Pliers/Crimpers 8.0” Adjustable Wrench
1000Volt
Insulated Slotted: 2.5, 3.0, 3.5,
4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm
Insulated Phillips: #0, 1, 2, 3
Insulated Xeno Slotted/Phillips
Terminal: #1, 2
Insulated Square: #1, 2
Insulated TORX: T6, T7, T8, T9,
T10, T15, T20, T25, T30
Insulated T-handle Inch Hex:
5/32, 3/16, 7/32, 1/4, 5/16, 3/8”
Insulated T-handle Metric Hex:
4.0, 5.0, 6.0, 8.0mm
Insulated Cable Knife: 50mm
Insulated Folding Ruler In/MM
Insulated Inch Sockets: 1/2, 9/16,
5/8, 11/16, 3/4, 13/16, 7/8”
Insulated Metric Sockets:
13.0, 14.0, 15.0, 17.0, 19.0,
20.0, 22.0mm
Insulated Ratchet 3/8” Drive
Insulated 4.9” Extension 3/8” Dr.
Insulated Inch Nut Drivers:
7/32, 1/4, 5/16, 3/8, 7/16”
Insulated Metric Nut Drivers:
5.0, 5.5, 6.0, 7.0, 8.0,
10.0, 13.0mm
Insulated L-key: 10mm
Insulated L-key: 1/2”
Cat. III Voltage Detector-
Battery Operated
All Tools
In Dedicated
Positions
For Quick
Storage &
Easy Location
Tracking
Insulation Test Standards:
Insulation according to EN/IEC 60900,
ASTM F-1505, New VDE 0682/part 201,
DIN 7437, NFPA70E & CSA
Inch
Metric
Insulated Inch Deep Offset Ring
Wrenches: 1/4, 5/16, 3/8, 7/16,
1/2, 9/16, 5/8, 11/16, 3/4, 25/32,
13/16, 7/8, 15/16, 1, 1-1/16, 1-1/4”
Insulated Metric Deep Offset
Ring Wrenches: 8.0, 9.0,
10.0, 11.0, 12.0, 13.0, 14.0, 15.0,
17.0, 19.0, 20.0, 22.0, 24.0, 27.0,
30.0, 32.0mm
Wiha Insulated Master Electrician’s Tools
32800
32800
32801
32801
www.wihatools.com
30
80 Piece Insulated Master Electrician’s Set
Item# Set Includes: lbs. 27.0
6.3” Long Nose Pliers 6.3” Diagonal Cutters
6.3” Bent Nose Pliers 8.0” BiCut SuperCut
8.0” Long Nose Pliers 8.0” Cable Cutters
6.3” Long Flat Nose Pliers 6.3” Stripping Pliers
9.0” Combo Pliers/Crimpers 8.0” Adjustable Wrench
1000Volt
Insulated Slotted 2.0mm
Insulated Slotted 2.5mm
Insulated Slotted 3.0mm
Insulated Slotted 3.5mm
Insulated Slotted 4.0mm
Insulated Slotted 4.5mm
Insulated Slotted 5.5mm
Insulated Slotted 6.0mm
Insulated Slotted 6.5mm
Insulated Slotted 8.0mm
Insulated Slotted 10.0mm
Insulated Phillips #0
Insulated Phillips #1
Insulated Phillips #2
Insulated Phillips #3
Insulated Nut Driver 7/32”
Insulated Nut Driver 1/4”
Insulated Nut Driver 5/16”
Insulated Nut Driver 3/8”
Insulated Nut Driver 7/16”
Insulated T-handle Hex 5/32”
Insulated T-handle Hex 3/16”
Insulated T-handle Hex 7/32”
Insulated T-handle Hex 1/4”
Insulated T-handle Hex 5/16”
Insulated T-handle Hex 3/8”
Insulated Torx T6
Insulated Torx T7
Insulated Torx T8
Insulated Torx T9
Insulated Torx T10
Insulated Torx T15
Insulated Torx T20
Insulated Torx T25
Insulated Torx T30
Insulated Square #1
Insulated Square #2
Insulated Slt/Ph Terminal #1
Insulated Slt/Ph Terminal #2
Insulated Cable Knife 50mm
Insulated Folding Ruler In/MM
Insulated Nut Driver 5.0mm
Insulated Nut Driver 5.5mm
Insulated Nut Driver 6.0mm
Insulated Nut Driver 7.0mm
Insulated Nut Driver 8.0mm
Insulated Nut Driver 10.0mm
Insulated Nut Driver 13.0mm
Insulated T-handle Hex 4.0mm
Insulated T-handle Hex 5.0mm
Insulated T-handle Hex 6.0mm
Insulated T-handle Hex 8.0mm
Insulated Socket 1/2”
Insulated Socket 9/16”
Insulated Socket 5/8”
Insulated Socket 11/16”
Insulated Socket 3/4”
Insulated Socket 13/16”
Insulated Socket 7/8”
Insulated Socket 13mm
Insulated Socket 14mm
Insulated Socket 15mm
Insulated Socket 17mm
Insulated Socket 19mm
Insulated Socket 20mm
Insulated Socket 22mm
Insulated Ratchet 3/8” Dr.
Insulated 4.9” Extension
Insulated L-key 10mm
Insulated L-key 1/2”
80 Pc.
BIGGEST
SET
Wiha 1000Volt Insulated Tool Sets - Comfort Grip Handles
Item# Set Includes: lbs. 21.5
8.0” Long Nose 6.3” Side Cutters
6.3” Long Flat Nose 8.0” BiCut SuperCut
9.0” Combo Pliers/Crimpers 6.3” Stripping Pliers
8.0” Cable Cutters 8.0” Adjustable Wrench
Insulated Nut Driver 1/4” Insulated Slotted 2.0mm
Insulated Nut Driver 5/16” Insulated Slotted 2.5mm
Insulated Nut Driver 11/32” Insulated Slotted 3.0mm
Insulated Nut Driver 3/8” Insulated Slotted 4.0mm
Insulated Nut Driver 7/16” Insulated Slotted 4.5mm
Insulated T-handle Hex 4.0mm Insulated Slotted 5.5mm
Insulated T-handle Hex 5.0mm Insulated Slotted 6.0mm
Insulated T-handle Hex 6.0mm Insulated Slotted 8.0mm
Insulated T-handle Hex 8.0mm Insulated Slotted 10.0mm
Insulated T-handle Hex 5/32” Insulated Phillips #0
Insulated T-handle Hex 3/16” Insulated Phillips #1
Insulated T-handle Hex 7/32” Insulated Phillips #2
Insulated T-handle Hex 1/4” Insulated Phillips #3
Insulated T-handle Hex 5/16” Insulated Torx T8
Insulated T-handle Hex 3/8” Insulated Torx T10
Insulated Hex L-key 10.0mm Insulated Torx T15
Insulated Hex L-key 1/2” Insulated Torx T20
Insulated Socket 1/2” Insulated Torx T25
Insulated Socket 9/16” Insulated Torx T30
Insulated Socket 5/8” Insulated Square #1
Insulated Socket 11/16” Insulated Square #2
Insulated Socket 3/4” Insulated Slt/Ph Terminal #1x80
Insulated Socket 13/16” Insulated Slt/Ph Terminal #2x100
Insulated Socket 7/8” Insulated Cable Knife 50mm
Insulated Socket 8.0mm Insulated Extension 4.9”
Insulated Socket 10.0mm Insulated Ratchet 3/8” Driver
Insulated Socket 13.0mm Insulated Socket 17.0mm
Insulated Socket 14.0mm Insulated Socket 19.0mm
Insulated Socket 15.0mm Insulated Socket 22.0mm
66 Pc. Master Electrician’s Set. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. Pliers drop-forged from special
tool steel, individually high frequency induction hardened, chrome/nickel
plated, mirror-polished.
1000Volt
Master Electrician’s Sets
66 Pc.
BIGGER
SET
32877
32877
32876
32876
Toll Free: (800) 494-6104
31
Wiha 1000Volt Insulated Tool Sets - Comfort Grip Handles
Item# Set Includes: lbs. 12.85
6.3” Long Nose Pliers 6.3” Side Cutters
8.0” Long Nose Pliers 8.0” BiCut SuperCut
7.0” Linemans Pliers 6.3” Stripping Pliers
9.0” Combination Pliers 6.3” Round Nose Pliers
Slotted: 2.0, 2.5, 3.0, 3.5, 4.5, 5.5, 6.5, 8.0, 10.0mm
Phillips: #0, #1, #2, #3
Inch Nut Driver: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8, 7/16, 1/2, 9/16”
31 Pc. Pliers & Screwdriver Set. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. Pliers drop-forged from special
tool steel, individually high frequency induction hardened, chrome/nickel
plated, mirror-polished. Set includes Insulated Inch & Metric folding ruler.
1000Volt 31 Pc.
Set
Item# Set Includes: lbs. 11.92
8.0” Long Nose 6.3” Stripping Pliers
9.0” Combination Pliers Insulated Inch & Metric Folding Ruler
8.0” BiCut SuperCut 8.5” Insulated Knife
Slotted: 3.0, 4.5, 6.0mm Phillips: #1, #2
Square: #1, #2 Terminal Block Driver: #1, #2
Inch Nut Driver: 1/4, 5/16, 11/32, 3/8, 7/16, 1/2”
Metric Nut Driver: 7.0, 8.0, 10.0, 13.0mm
25 Pc. Pliers & Screwdriver Set. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E &
CSA, up to 1000 volt. Individually Tested.
Pliers drop-forged from special tool steel, individually high frequency
induction hardened, chrome/nickel plated, mirror-polished. In tool box.
1000Volt
25 Pc.
Set
50 Piece Insulated Tool Set. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. Pliers drop-forged from special
tool steel, individually high frequency induction hardened, chrome/nickel
plated, mirror-polished. Cushion Grip Insulated handles. Canvas tool bag.
1000Volt
50 Pc.
BIG SET
13 Piece Pliers & Screwdriver Set. In canvas tool bag
Item# Set Includes: lbs. 5.16
8.0” Long Nose 50mm Cable Stripping Knife
8.0” BiCut SuperCut Insulated Slotted: 3.0mm
9.0” Combo Pliers/Crimpers Insulated Slotted: 4.5mm
Insulated Phillips: #1 Insulated Slotted: 6.0mm
Insulated Phillips: #2 Insulated Square: #1
Insulated Slt/Ph Terminal: #1 Insulated Square: #2
Insulated Slt/Ph Terminal: #2
Item# Set Includes: lbs. 19.8
6.3” Long Nose Pliers 6.3” Side Cutters
8.0” Long Nose Pliers 8.0” BiCut SuperCut
6.3” Combination Pliers 6.3” Stripping Pliers
9.0” Combo Pliers/Crimpers 8.0” Adjustable Wrench
10.0” Water Pump Pliers Battery Operated Voltage Detector
Slotted: 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0mm
Phillips: #0, 1, 2, 3 Square: #1, 2 Slt/Ph Terminal: #1, 2
TORX: T8, T9, T10, T15, T20, T25, T27, T30
Hex Inch: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8”
Nut Driver Inch: 7/32, 1/4, 5/16, 3/8, 7/16, 1/2”
50mm Cable Stripping Knife & Insulated Inch/Metric Folding Ruler
1000Volt
13 Pc.
Set
32874
32874
32879
32879
32896
32896
32878
32878
www.wihatools.com
32
1000Volt
10 Piece Pliers & Screwdriver Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Item# Set Includes: lbs. 5.54
8.0” Combination Pliers 8.0” Long Nose
8.0” BiCut SuperCut 6.3” Cable Cutters
6.3” Universal Wire Stripper
Insulated Phillips #1 Insulated Slotted 4.5mm
Insulated Phillips #2 Insulated Slotted 6.5mm
Insulated Phillips #3
10 Piece Pliers & Screwdriver Set. Insulation According
to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E
& CSA, up to 1000 volt. Individually Tested. Pliers drop-forged
from special tool steel, individually high frequency induction hardened,
chrome and nickel plated, mirror-polished. In canvas tool bag
Item# Set Includes: lbs. 6.64
8.0” Bent Nose 8.0” Combination Pliers
6.3” Long Nose 6.3” Side Cutters
Insulated Phillips #0 Insulated Slotted 3.0mm
Insulated Phillips #1 Insulated Slotted 4.5mm
Insulated Phillips #2 Insulated Slotted 6.5mm
13 Piece Pliers & Screwdriver Set In canvas tool bag
Item# Set Includes: lbs. 9.5
8.0” Bent Nose 8.0” Combination Pliers
6.3” Long Nose 6.3” Side Cutters
10” Water Pump Pliers
Insulated Slotted: 4.5 & 6.5mm Insulated Nut Driver:
Insulated Phillips: #1 & #2 1/4, 5/16, 3/8, 1/2”
Item# Set Includes: lbs. 6.60
8.0” Long Nose 6.3” Side Cutters
9.0” Combination Pliers 8.0” BiCut SuperCut
6.3” Stripping Pliers Insulated Slotted 2.5mm
Insulated Phillips #1 Insulated Slotted 3.0mm
Insulated Phillips #2 Insulated Slotted 3.5mm
Insulated Phillips #3 Insulated Slotted 4.5mm
Insulated Slotted 2.0mm Insulated Slotted 6.5mm
14 Piece Pliers & Screwdriver Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Wiha Insulated Pliers with High Visibility Comfort Grip Handle
11 Piece Pliers & Screwdriver Set In Canvas Pouch
Item# Set Includes: lbs. 3.58
6.3” Long Nose 6.3” Side Cutters
8.0” Combination Pliers 6.3” Stripping Pliers
Insulated Slotted 2.5mm Insulated Phillips #0
Insulated Slotted 3.5mm Insulated Phillips #1
Insulated Slotted 4.5mm Insulated Phillips #2
Insulated Slotted 6.0mm
1000Volt
1000Volt
1000Volt 1000Volt
32891
32891
32895
32895
32894
32894
32892
32892
32888
32888
• Pliers drop-forged
from special tool steel,
individually high
frequency induction
hardened, chrome
and nickel plated,
mirror-polished.
• In zipper carry case
• Pliers drop-forged
from special tool steel,
individually high
frequency induction
hardened, chrome
and nickel plated,
mirror-polished.
• In zipper carry case
Toll Free: (800) 494-6104
33
8 Piece Pliers & Cutters Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Item# Set Includes: lbs. 4.63
6.3” Long Nose Pliers 8.0” Long Nose Pliers
6.3” Lineman’s Pliers 6.3” Diagonal Cutters
9.0” Lineman’s Pliers 8.0” BiCut SuperCut
6.3” Wire Stripping Pliers Electrician’s Knife
• Pliers drop-forged
from special tool steel,
individually high
frequency induction
hardened, chrome
and nickel plated,
mirror-polished.
1000Volt
Wiha Insulated Pliers with High Visibility Comfort Grip Handle
10 Piece Pliers & Screwdriver Set In Canvas Pouch
Item# Set Includes: lbs. 4.06
6.3” Diagonal Cutters 9.0” Combo Pliers
6.3” Long Nose Pliers 6.3” Wire Strippers
7.0” Crimping Pliers
Insulated Slotted 4.5mm Insulated Phillips #1
Insulated Slotted 6.0mm Insulated Phillips #2
Insulated Square: #2
10 Piece Pliers & Screwdriver Set In Canvas Pouch
Item# Set Includes: lbs. 4.24
7.0” Diagonal Cutters 9.0” Combo Pliers
8.0” Long Nose Pliers 6.3” Wire Strippers
7.0” Crimping Pliers
Insulated Slotted 3.0, 4.5, 6.0mm
Insulated Phillips #1, 2
14 Piece Pliers/Cutters & Screwdrivers Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Item# Set Includes: lbs. 6.52
9.0” Lineman’s Pliers 8.0” BiCut SuperCut
8.0” Cable Cutters 8.0” Long Nose Pliers
6.0” Stripping Pliers 10-20 AWG
SlimLine Slotted 3.0, 4.5, 6.5mm SlimLine Phillips #1, 2
SlimLine Square #1, 2 SlimLine Terminal #2
Single Pole Tester
1000Volt
1000Volt
1000Volt
7 Pc. Pliers & Driver Set. Insulation According to VDE
0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. In molded tool box
Item# Set Includes: lbs. 5.39
9.0” Linemans Pliers 6.3” Long Nose Pliers W/Cutter
6.3” Diagonal Cutter
Insulated Phillips #1, 2 Insulated Slotted 3.0, 4.5mm
1000Volt
32889
32889
32867
32867 32868
32868
32869
32869
32899
32899
www.wihatools.com
34
Insulated Pliers/Cutters & Screwdrivers Sets
5 Pc. Insualted Pliers/Cutters & Screwdriver Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC. Screwdriver blade
high alloy CVM steel, hardened, black finish. Insulation molded directly
onto blade. Wiha-SoftFinish® handle, multi-component, cushion grip.
Item No. Insulated Pliers/Cutters
8.0” Long Nose Pliers
6.3” Diagonal Cutters
lbs. Insulated Slotted & Phillips Drivers
1.81 Slotted: 4.5, 5.5mm
Phillips: #2
1000Volt
8 Pc. Insualted Pliers/Cutters & SlimLine Blade Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC. SlimLine blades high
alloy CV steel, through hardened. Blades have up to 33% narrower
insulation diameter then standard insulated tools.
Item No. Insulated Pliers/Cutters
8.0” Long Nose Pliers
Insulated Slotted & Phillips SlimLine Blades
lbs. Slotted: 3.0, 4.0, 5.5, 6.5mm
.98 Phillips: #1, #2
1000Volt
7 Pc. Insualted Pliers/Cutters & Screwdriver Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC. Screwdriver blade
high alloy CVM steel, hardened, black finish. Insulation molded directly
onto blade. Wiha-SoftFinish® handle, multi-component, cushion grip.
Item No. Insulated Pliers/Cutters
8.0” Combination Lineman’s Pliers
Insulated Slotted & Phillips Drivers
lbs. Slotted: 3.5, 4.5, 5.5mm
1.81 Phillips: #0, #1, #2
1000Volt
7 Pc. Insualted Pliers/Cutters & Screwdriver Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC. Screwdriver blade
high alloy CVM steel, hardened, black finish. Insulation molded directly
onto blade. Wiha-SoftFinish® handle, multi-component, cushion grip.
Item No. Insulated Pliers/Cutters
8.0” BiCut SuperCut Pliers
Insulated Slotted & Phillips Drivers
lbs. Slotted: 3.5, 4.5, 5.5mm
1.85 Phillips: #0, #1, #2
1000Volt
32856
32856
32865
32865
32858
32858
32857
32857
Toll Free: (800) 494-6104
35
2 Pc. NE Style Lineman’s Pliers Set
Item No. NE Style Lineman’s Pliers
9.5” Insulated & 9.5” Vinyl Soft Grip - Lineman’s Pliers
lbs. 2.22
1000Volt
Insulated Tool
meets ASTM, IEC,
EN, NFPA
& CSA standards
Individually Tested
Extra long cutting edge for
flat and round cables
NE Style Lineman’s Pliers Set
Knurled striking
zone on vinyl
grip pliers
Insulated BiCut SuperCut
· Double the power at the press of a button
· BiCut does the job of two pairs of pliers
· Up to 50% less hand strength required for cutting
· Cutting force doubled for extremely hard materials
· Easily switch between two strengths in one-handed operation
Item
No. mm Inch Pkg. lbs.
200 8.0 1 .78
Insulated BiCut SuperCut. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 Volt. Individually Tested. Durable cutting is achieved
through additional inductive hardening to approx. 64HRC. Drop forged of
high C70 steel. For cutting various materials from soft to extremely hard,
such as nails, screws, bolts, wire cables, spring wires, chains, etc.
1000volt
Cutting capacity up to 3mm
hardened piano wire
3 Pc. Insualted Pliers & Cutters Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC.
Item No. Insulated Pliers & Cutters
6.3” Diagonal Cutters
lbs. 8.0” Long Nose Pliers
1.94 8.0” Combination Lineman’s Pliers
1000Volt
3 Pc. Insualted Pliers/Cutters & Stripping Pliers Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC.
Item No. Insulated Pliers/Cutters & Stripping Pliers
8.0” High Leverage Diagonal Cutters
lbs. 9.0” Lineman’s Pliers W/Crimpers
2.21 6.3” Stripping Pliers Strips 0.81-2.59 / AWG #20-#10
2 Pc. Insualted Pliers & Cutters Set
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Pliers drop forged of high C70 steel. Durable cutting is achieved through
additional inductive hardening to approx. 64HRC.
Item No. Insulated Pliers & Cutters Pliers lbs. 1.66
8.0” BiCut SuperCut Pliers
8.0” Combination Pliers
1000Volt
1000Volt
Insulated Pliers & Cutters Sets
32833
32833
32837
32837
32864
32864
32863
32863
32862
32862
www.wihatools.com
Insulated Combination Lineman’s Pliers
Item
No. mm Inch Pkg. wt.
160 6.3 #10 1 .53
180 7.0 #9 1 .58
200 8.0 #8 1 .72
Combination Pliers. Insulation According to VDE 0682/
part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to
1000 volt. Individually Tested. DIN ISO 5746 Extra long cutting edge
for flat & round cables. Serrated jaws. Cutting edges additionally
induction hardened to approx. 64HRC. C70 Special tool steel, Chrome
finish. Use for gripping and holding as well as cutting soft and hard wires
and cables. Two component soft grip ergonomic handles.
1000volt
Safety slip
guard
Hard chrome finish for long
lasting corrosion protection
Cutters additionally
induction hardened
Soft grip ergonomically
designed handle body
Insulated High Leverage Combination Pliers
Lineman’s
Item
No. mm Inch Pkg. wt.
225 9.0 #4 1 .86
High Leverage Combination Pliers. Insulation According
to EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000
volt. Individually Tested. DIN ISO 5746
Extra long cutting edge for flat and round cables. Serrated jaws. Cutting
edges additionally induction hardened to approx. 64HRC. C70 Special
tool steel. Use for gripping, pulling & holding as well as cutting wires and
cables ranging in hardness from soft to extremely hard. Two component
soft grip ergonomic handles.
Cutting Capacity
Copper AWG
Cutting Capacity
Copper AWG
Insulated Linemans Pliers With Crimpers
5-In-1
Lineman’s Pliers
With
Lower
Crimping
Jaw
Item
No. mm Inch Pkg. wt.
225 9.0 #4 1 .98
Insulated Lineman’s Pliers “5-In-1” Professional Design
Insulation According to EN/IEC, ASTM, NFPA70E & CSA,
up to 1000 volt. Individually Tested.
Deep cut radius conduit jaws for non-slip handling. Sure grip knurled
& cross hatched flat jaw for non-slip griping. Extra long induction
hardened precision matched cutting edges. Lower crimping jaw accepts
most standard non-insulated electrical connectors. Large head with
square anvil surface on each side. Made from premium CV tool steel
forgings. Two component cushion grips for best user comfort.
Cutting Capacity
Copper AWG
36
Item
No. mm Inch mm2 AWG Pkg. wt.
180 7.0 0.25-2.5 6-30 1 .57
Insulated Crimping Pliers. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E
and CSA, up to 1000 Volt. Individually Tested.
Semi-circular profiles for secure connection between end sleeve and
conductor. Long life is achieved through additional induction hardening
to 64HRC. C70 special tool steel hardened & tempered.
Insulated Crimping Pliers
64HRC
cutting edges
Insulated Pliers
& Cutters
1000volt
Item
No. mm Inch Pkg. wt.
245 9.5 1 1.18
Insulated NE Style Lineman’s Pliers. Insulation
According to EN/IEC 60900, ASTM F-1505, NFPA70E and CSA,
up to 1000 Volt. Individually Tested. Long life edge is achieved
through additional induction hardening to approx. 64HRC. Special C70
tool steel hardened & tempered. Extra long cutting edge for flat and
round cables. Two component soft grip ergonomic handles.
Insulated NE Style Lineman’s Pliers
1000volt
1000volt
1000volt
New dynamic joint provides 40% easier
cuts & significantly longer tool life
32821
32821
32820
32820
32814
32816
32818
328
32841
32841
32831
32831
Toll Free: (800) 494-6104
37
Insulated Diagonal Cutters
Item
No. mm Inch Pkg. wt.
140 5.5 #6 1 .47
160 6.3 #6 1 .49
180 7.0 #6 1 .62
Diagonal Cutters. Insulation According to VDE 0682/part 201,
EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt.
Individually Tested. DIN ISO 5749 Low wear lap joint, riveted and
able to withstand high levels of load. Lightweight action, clean
cutting. Long term cutting is achieved through additional inductive
hardening to approx. 60 HRC. Special tool steel hardened and tempered.
For soft & medium hard wire. 32832 & 32834 for soft, hard & piano wire.
Item
No. mm Inch Pkg. wt.
160 6.3 #6 1 .64
180 7.0 #5 1 .67
200 8.0 #4 1 .80
High Leverage Diagonal Cutters. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. DIN ISO 5749
Semi-circular. Low wear lap joint, riveted and able to withstand high
levels of load. Lightweight action, clean cutting. Long term cutting is
achieved through additional inductive hardening to approx. 64HRC.
C70 special tool steel hardened and tempered to high quality. For soft,
hard and piano wire, lay-on joint, optimized power transmission.
Insulated High Leverage Diagonal Cutters
Cutting Capacity
Copper AWG
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. wt.
160 6.3 #6 1 .55
Diagonal Cutters W/Stripping Holes. Insulation According
to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E &
CSA, up to 1000 volt. Individually Tested. Drop-forged from special
tool steel, cutters additionally induction hardened to approx. 64HRC,
chrome-nickel plated, mirror-polished. Ergo comfort grip with slip guard.
Holes in the cutting edge for stripping copper wire of Ø 1.5 and 2.5.
Insulated Electrician’s Diagonal Cutters
Cutting Capacity
Copper AWG
1000volt
Item
No. mm Inch Ø mm2 Pkg. lbs.
160 6.3 16 50 1 .42
200 8.0 20 60 1 .67
Serrated Edge Cable Cutters. Insulation According to VDE
0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA,
up to 1000 Volt. Individually Tested. Light, clean cutting ground
precision cutting edges. Durable cutting is achieved through additional
inductive hardening to approx. 64HRC. Special tool steel, hardened &
tempered. For cutting of copper & aluminum cables without crushing.
Insulated Serrated Edge Cable Cutters
Strips AWG
#10 & #14
New dynamic joint provides 40% easier
cuts & significantly longer tool life
64HRC cutting
edges
Stripping Pliers. Insulation According to VDE 0682/part
201, EN/IEC 60900, ASTM F-1505, NFPA70E and CSA,
up to 1000 volt. Individually Tested. Heavy duty forged, induction
hardened cutting edges for even stripping of insulation. Drop-forged from
special tool steel, chrome and nickel plated, mirror-polished. Spring and
adjusting screw, for stripping up to Ø 5mm/#4 Awg.
Item
No. mm Inch Pkg. wt.
160 6.3 #8 - #28 1 .50
1000volt
Insulated Stripping Pliers
Stripping Capacity
Copper AWG
64HRC cutting
edges
Item No. mm Inch Ø AWG Pkg. lbs.
160 6.3” 0.81-2.59 20-10 1 .26
1000Volt
Insulated Stripping Pliers
Insulated Stripping Pliers. Insulation According to
EN/IEC 60900, DIN ISO 8976, ASTM F-1505 & CSA Specification.
Individually Tested. Wide long head with ridged gripping surface, shears
blade and firm wire stripping stations. Wire stripping stations 0.81 / 1.0 /
1.3 / 1.6 / 2.0 / 2.59mm, AWG 20 / 18 / 16 / 14 / 12 / 10.
1000volt
1000volt
1000volt
32830
32832
32834
328
32835
32836
32838
328
32861
32861
32826
32828
328
32860
32860
10250
10250
www.wihatools.com
Insulated Long Nose Pliers
1000volt
Item
No. mm Inch Pkg. wt.
160 6.3 #10 1 .32
200 8.0 #8 1 .42
Long Nose Pliers With Cutters. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. Drop-forged from special
tool steel, cutters additionally induction hardened to approx. 64HRC,
chrome-nickel plated, mirror-polished.
Item
No. mm Inch Pkg. wt.
200 8.0 #8 1 .43
160 6.3 #10 1 .32
Bent Nose Pliers With Cutters. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Drop-forged from special tool steel, cutters
additionally induction hardened to approx. 64HRC, chrome-nickel plated,
mirror-polished. Serrated gripping surface, nose bent 40o.
Insulated Bent Nose Pliers
Angled 40O
1000volt
Cutting Capacity
Copper AWG
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. wt.
160 6.3 1 .34
Round Nose Pliers. Insulation According to VDE 0682/
part 01, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA, up to
1000 volt. Individually Tested. Drop-forged from special tool
steel, individually induction hardened, chrome and nickel plated,
mirror-polished. Ergonomic comfort grip with slip guard. Serrated jaws.
1000volt
Insulated Round Nose Pliers
Item
No. mm Inch Pkg. wt.
160 6.3 1 .39
Long Flat Nose Pliers. Insulation According to
VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. DIN ISO 5745
Extra long head. Serrated Jaws are induction hardened. Special CV
tool steel forgings, Chrome finish. Two component Soft Grip handles.
Use for Gripping and right-angle bending of wires and sheet metal parts.
1000volt
Insulated Long Flat Nose Pliers
38
Wiha Canvas Pliers Holster
Pliers Canvas Holster
Item Width Height
No. Size Size lbs. pkg.
3.5 x 6.75 .15 1
· Canvas holster with belt clip and belt loop
· Security pliers strap
· Screwdriver holder in the front
Switch Cabinet Key
Item No. mm Inch Pkg. lbs.
76 3.0” 1 .22
Switch Cabinet Keys For applications with all common
switch cabinets and locking systems. Diecast Zinc
Item No. mm Inch Pkg. lbs.
140 5.5” 1 .30
Pen Style Control Cabinet Key Diecast Zinc, polished
finish. Includes: Square 5, 6, 7, 8mm, Triangular 9mm, Double Bit Key
5mm/Internal & 9mm/External, Universal 1/4” Bit Adapter, Magnetic Bit
Holder & 2 Double Insert Bits: Slotted 7mm / Phillips #2, TORX T20/T25
Pen Style Control Cabinet Key
For applications with all
common switch cabinets
and locking systems
32806
32808
328
32804
32807
328
32870
32870
32810
32810
91256
91256
21103
21103
21105
21105
Toll Free: (800) 494-6104
39
Item
No. mm Inch Pkg. lbs.
180 7.0 #6 1 .46
Inomic Combo Pliers. Insulation According to EN/IEC
60900, ASTM F-1505, NFPA70E & CSA, up to 1000 volt.
Individually Tested. DIN ISO 5749 Precision machined forged head.
Induction hardened for longest tool life. Cross hatched flat jaw & deep
cut radius jaws for secure gripping of the work piece. Cutting edges are
matched for precise cutting action. Award winning ergonomic design
with head mounted at 23° angle to grip for reduced user fatigue. Palm
side of grip has molded soft panel for added comfort in prolonged use.
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. lbs.
160 6.3 #6 1 .43
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. lbs.
160 6.3 #6 1 .41
Inomic Diagonal Cutters
Cutting Capacity
Copper AWG
Wiha Inomic 1000Volt Insulated Pliers
Each tool includes
a convenient jaw lock &
handle return spring
Heads drop forged
CV premium tool steel
Inomic Canvas Holster
Item Width Height
No. Size Size lbs. pkg.
4.0 x 4.5 .05 1
Holds any
Inomic Pliers
Award winning ergonomic design
with head mounted at 23° angle to
grip for reduced user fatigue
Inomic Long Nose Pliers
32850 32852 32854
Item
No. mm Inch Pkg. lbs.
160 6.3 1 .22
Proturn Insulated Electrician’s Shears
Insulation meets VDE, ASTM F1505, EN/IEC 60900, CSA, NFPA
70E, OSHA Specifications. Made from stainless 420 grade steel
Proturn Insulated Electrician’s Shears
Insulated Water Pump Pliers
Item
No. mm Inch Pkg. wt.
250 10.0 1 3/4 2 1 .90
Insulated Industrial Water Pump Pliers. Insulation
According to VDE, EN/IEC, ASTM, NFPA70E & CSA, up to
1000 Volt. Individually Tested. 10 opening settings provides optimal
adjustment to objects being gripped. Long life achieved through
additional induction hardening of jaws to approx. 62HRC. Chrome-
vanadium tool steel forgings, hardened and tempered. Black finish.
Item
No. mm Inch Pkg. wt.
250 10.0 1 3/4 2” 1 .90
Insulated Industrial Push Button Water Pump Pliers.
Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA,
Individually Tested. Extra narrow head for working in small spaces.
Long life achieved through additional induction hardening of jaws to
approx. 62HRC. Finger jam protection for safe operation at all settings.
CVM tool steel forgings, hardened & tempered.
Capacities
Round Hex
Capacities
Round Hex
1000volt
1000volt
Item
No. Meter Inch Sections Increments lbs. pkg.
2 78” 10 1/16 & 1mm .31 1
Insulated Inch & Metric Folding Ruler
10,000Volt Tested/1000Volt Rated. Inch & Metric deep embossed
scales. 10 folding sections. 30% fiberglass reinforced polyimide.
With Wire
Puller Slot
Rapid & simple
push button
setting &
locking
Meets VDE,
EN/IEC,
ASTM,
CSA,
NFPA
standards
1000volt
32850
32850
32852
32854
32852
32854
91230
91230
32951
32951
32954
32954
32956
32956
61630
61630
www.wihatools.com
Induction hardened
jaws and cutters
to 64 HRC
1000V
Two component
ergo cushion grip
handles
New dynamic joint
provides 40% easier
cuts & significantly
longer tool life
40
Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards
1000volt
Insulated Lineman’s Pliers With Crimpers
Insulated Long Nose Pliers With Cutters
Insulated Diagonal Cutters
Industrial
brushed
finish
Insulated Industrial Pliers & Cutters
Item
No. mm Inch Pkg. wt.
225 9.0 #4 1 .98
Insulated Industrial Lineman’s Pliers “5-In-1” Professional
Design. Insulation According to EN/IEC, ASTM, NFPA70E & CSA,
up to 1000 volt. Individually Tested. Deep cut radius conduit
jaws for non-slip handling. Sure grip knurled & cross hatched flat jaw
for non-slip griping. Extra long induction hardened precision matched
cutting edges. Lower crimping jaw accepts most standard non-insulated
electrical connectors. Large head with square anvil surface on each side.
Premium CV tool steel forgings.
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. wt.
160 6.3 #10 1 .36
200 8.0 #8 1 .46
Insulated Industrial Long Nose Pliers With Cutters.
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E & CSA, up to 1000 volt. Individually Tested.
Drop-forged from special tool steel, cutters additionally induction
hardened to approx. 64HRC, half-round jaws, serrated gripping surface.
Cutting Capacity
Copper AWG
Item
No. mm Inch Pkg. wt.
160 6.3 #6 1 .64
200 8.0 #6 1 .80
Insulated Industrial Diagonal Cutters. Insulation According
to VDE, EN/IEC, ASTM, NFPA70E & CSA, 1000Volt Rated. Individually
Tested. DIN ISO 5749 Low wear lap joint, riveted and able to withstand
high levels of load. Lightweight action, clean cutting. Long term cutting is
achieved through additional inductive hardening to approx. 64HRC. Special
tool steel hardened & tempered. For soft, medium hard wire & piano wire.
Cutting Capacity
Copper AWG
Long life high
performance
dynamic 60/40 joint
Long life high
performance
dynamic
60/40 joint
64HRC
cutting edges
1000volt
Ergo comfort grip
with slip guard
1000volt
Item
No. mm Inch Pkg. wt.
200 8.0 #4 1 .66
Insulated Industrial High Leverage Diagonal Cutters.
Insulation According to VDE, EN/IEC, ASTM, NFPA70E & CSA,
1000 volt rated. Individually Tested. DIN ISO 5749 Semi-circular.
Low wear lap joint, riveted and able to withstand high levels of load.
Lightweight action, clean cutting. Long term cutting is achieved through
additional inductive hardening to approx. 64HRC. C70 special tool steel
hardened and tempered to high quality. For soft, hard and piano wire,
lay-on joint, optimized power transmission.
Cutting Capacity
Copper AWG
Insulated High Leverage Diagonal Cutters
Item
No. mm Inch Pkg. wt.
245 9.5 1 1.18
Insulated NE Style Lineman’s Pliers. Insulation
According to EN/IEC 60900, ASTM F-1505, NFPA70E and CSA,
up to 1000 Volt. Individually Tested. Long life edge is achieved
through additional induction hardening to approx. 64HRC. Special C70
tool steel hardened & tempered. Extra long cutting edge for flat and
round cables.
Insulated NE Style Lineman’s Pliers
1000volt
Long life high
performance dynamic
60/40 joint
Knurled
Striking Zone
1000volt
32917
32917
329
32926
32923
329
32933
32929
32939
32939
32938
32938
Toll Free: (800) 494-6104
41
Insulated Industrial Stripping Pliers. Insulation According
to VDE, EN/IEC, ASTM, NFPA70E & CSA, 1000Volt Rated.
Individually Tested. DIN ISO 5745 Made from Premium CV tool steel
forgings. Induction hardened jaws and cutters to 64HRC. Spring &
adjusting screw, for stripping up to Ø 5mm/#4 Awg.
Item
No. mm Inch Pkg. wt.
160 6.3 #8 - #28 1 .46
Stripping Capacity
Copper AWG
Insulated Combo Pliers With Dynamic Joint
Insulated Heavy Duty Cable Cutters Insulated Crimpers
Item
No. mm Inch Pkg. wt.
200 8.0 #4 1 .92
Insulated Industrial High Leverage Combination Pliers.
Insulation According to EN/IEC 60900, ASTM F-1505, NFPA70E &
CSA, up to 1000 volt. Individually Tested. DIN ISO 5746
Extra long cutting edge for flat and round cables. Serrated jaws. Cutting
edges additionally induction hardened to approx. 64HRC. Use for
gripping, pulling & holding as well as cutting wires and cables ranging in
hardness from soft to extremely hard.
Cutting Capacity
Copper AWG
Item
No. mm Inch Ø mm2 Pkg. lbs.
200 8.0 20 60 1 .78
Insulated Industrial Serrated Edge Cable Cutters.
Insulation According to VDE 0682/part 201, EN/IEC 60900, ASTM
F-1505, NFPA70E and CSA, up to 1000 Volt. Individually Tested.
Light, clean cutting ground precision cutting edges. Durable cutting is
achieved through additional inductive hardening to approx. 64HRC. For
cutting of copper & aluminum cables without crushing.
Item
No. mm Inch mm2 AWG Pkg. wt.
180 7.0 0.25-2.5 6-30 1 .64
Insulated Industrial Crimping Pliers. Insulation
According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505,
NFPA70E and CSA, up to 1000 Volt. Individually Tested.
Semi-circular profiles for secure connection between end sleeve and
conductor. Long life is achieved through additional induction hardening
to 64HRC. Crimps 6 - 30 AWG Connectors.
Long life high performance
dynamic 60/40 joint
1000volt
1000volt 1000volt
1000volt
Insulated TriCut Strippers & Cutters
1000volt
Item
No. mm Inch AWG Pkg. wt.
170 6.7 #6 1 .58
Insulated Industrial TriCut Strippers & Cutters. Insulation
According to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505,
NFPA70E and CSA, up to 1000 Volt. Individually Tested.
Induction hardened cutters & strippers. Cuts cable, strips cable, strips
wire leads. Unique 3 in 1 design provides faster combined cutting and
stripping. Strips AWG sizes #10 & #14.
Insulated Stripping Pliers
32947
32947
32930
32930
32927
32927
32945
32945
32944
32944
www.wihatools.com
42
5 Pc. Insulated Industrial Diagonal Cutters & Screwdrivers
Item No. Insulated Diagonal Cutters & Screwdrivers
6.3”/160mm Diagonal Cutter
Insulated Drivers: Slotted: 3.0, 4.5mm • Phillips: #1, #2
lbs. 1.17
1000Volt
6 Pc. Insulated Industrial Combo Pliers & Screwdrivers
Item No. Insulated Combination Pliers & Screwdrivers
8.0” Combination Pliers & 8” Long Nose Pliers
Drivers: Slotted: 3.0, 4.5mm • Phillips: #2 • Square: #2
lbs. 2.06
1000Volt
3 Pc. Insulated Industrial Pliers & Cutters
Item No. Insulated Pliers & Cutters
8.0” Combo Pliers, 8.0” Long Pliers, 8.0” Diagonal Cutters
lbs. 2.18
1000Volt
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
Individually
Tested
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
Individually
Tested
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
Individually Tested
Wiha Insulated Industrial Tool Sets
Insulated BiCut SuperCut & Screwdriver Set
7 Pc. Insulated Industrial BiCut SuperCut & Screwdrivers
Ergonomic two component molded grips. 10,000 Volt tested
Item No. Insulated BiCut SuperCut:
8.0”/200mm BiCut SuperCut
Insulated Cushion Grip Screwdivers:
lbs. Phillips: #0, #1, #2
1.86 Slotted: 3.0, 4.5, 5.5mm
1000volt
Tools meet ASTM, IEC, VDE, EN, NFPA & CSA standards
Insulated Industrial BiCut SuperCut
· Double the power at the press of a button
· BiCut does the job of two pairs of pliers
· Up to 50% less hand strength required for cutting
· Cutting force doubled for extremely hard materials
· Easily switch between two strengths in one-handed operation
Item
No. mm Inch Pkg. lbs.
200 8.0 1 .78
Insulated Industrial BiCut SuperCut. Insulation According
to VDE 0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 Volt. Individually Tested. Durable cutting is achieved
through additional inductive hardening to approx. 64HRC. Drop forged of
high C70 steel. For cutting various materials from soft to extremely hard,
such as nails, screws, bolts, wire cables, spring wires, chains, etc.
1000volt
Cutting capacity up to 3mm
hardened piano wire
32981
32981
32983
32983
32984
32984
32942
32942
32936
32936
Toll Free: (800) 494-6104
43
7 Pc. Insulated Industrial Pliers/Cutters & Screwdrivers
Item No. Insulated Pliers/Cutters & Screwdrivers
8.0” Combo Pliers, 6.3” Long Nose, 6.3” Diagonal Cutters
Insulated Drivers: Slotted: 3.0, 4.5mm • Phillips: #1, #2
lbs. 2.30
1000Volt
In Belt Pack Pouch
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
9 Piece Insulated Industrial Pliers & Cutters Set
Insulated pliers & cutters set in a light weight tool box tray.
Item No. 9.0” Lineman’s Pliers 8.0” High Lev. Combo Pliers
6.3” Long Nose Pliers 8.0” Cable Cutters
8.0” Long Nose Pliers 6.3” Stripping Pliers
lbs. 6.3” Diagonal Cutters 7.0” Crimping Pliers
6.34 8.0” Diagonal Cutters
1000Volt
Tool box set
in blow molded tray
Wiha Insulated Industrial Tool Sets
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
28 Piece Insulated Industrial Pliers & Cutters Set
Insulated pliers & cutters set in a light weight tool box tray.
Item No. Set Includes:
9.0” Lineman’s Pliers lbs.
8.0” High Leverage Combo Pliers 6.34
6.3” & 8.0” Long Nose Pliers
8.0” Cable Cutters
6.3” & 8.0” Diagonal Cutters
6.3” Stripping Pliers
7.0” Crimping Pliers
Slotted: 2.5, 3.0, 3.5, 4.0, 4.5, 5.5, 6.0, 6.5, 8.0, 10.0mm
Phillips: #0, #1, #2, #3
Xeno Slotted/Phillips: #1, #2 & Square: #1, #2
Cat. III Voltage Detector - Battery Operated
1000Volt
Tool box set
in blow molded trays
Wiha Insulated Tool Tray Sets
Tools meet ASTM,
IEC, VDE, EN,
NFPA & CSA
standards
3 Pc. Insulated Industrial Pliers/Cutters & Voltage Detector
Item No. Insulated Pliers/Cutters & Cat. III Voltage Detector
6.3” Long Pliers, 6.3” Diagonal Cutters
Voltage Detector with both light and sound alerts
lbs. .98
Notes:
32999
32999
32985
32985
32989
32989
32982
32982
www.wihatools.com
44
Wiha Insulated Industrial Tool Sets
11 Pc. Pliers & Screwdriver Set. Insulation According
to VDE 0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505,
NFPA70E, up to 1000 volt. Individually Tested. In Roll Out Pouch
Item# Set Includes: lbs. 3.62
6.3” Long Nose Pliers 6.3” Diagonal Cutters
8.0” Combination Pliers 6.3” Stripping Pliers
Insulated Slotted: 3.0, 4.5, 5.5mm
Insulated Phillips: #1, #2 Insulated Square: #1, #2
1000Volt
In Roll
Out
Pouch
8 Pc. Pliers & Cutters Set. Insulation According to
VDE 0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505,
NFPA70E, up to 1000 volt. Individually Tested. In Roll Out Pouch
Item# Set Includes: lbs. 5.52
6.3” Long Nose Pliers 6.3” Diagonal Cutters
8.0” Long Nose Pliers 8.0” H.D. Diagonal Cutters
9.0” Lineman’s w/Cutters 6.3” Stripping Pliers
8.0” Cable Cutters 7.0” Crimpers
1000Volt
22 Pc. Pliers & Cutters Set. Insulation According to VDE
0682/part 201, DIN EN 60900, EN/IEC 60900, ASTM F-1505, NFPA70E,
up to 1000 volt. Individually Tested. In Roll Out Pouches
Item# Set Includes: lbs. 5.74
8.0” Long Nose Pliers 6.3” Diagonal Cutters
9.0” Lineman’s w/Cutters 8.0” H.D. Diagonal Cutters
8.0” Cable Cutters 6.3” Stripping Pliers
7.0” Crimping Pliers
15 Pc. SlimLine Blade Set includes: Insulated SlimLine Blade Holder
Slotted: 3.0, 4.0, 5.5, 6.5 Phillips: #1, #2 Xeno: #1, #2
: T8, T10, T15, T20 Square: #1, #2
1000Volt
In Roll
Out
Pouch
In Roll
Out
Pouches
11 Pc. Pliers & Driver Set. Insulation According to VDE
0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. In canvas tool bag
Item# Set Includes: lbs. 6.30
8.0” Linemans Pliers 6.3” Long Nose Pliers W/Cutter
8.0” Long Nose Pliers W/Cutter 6.3” Diagonal Cutter
8.0” High Leverage Cutter
Insulated Phillips: #0, 1, 2 Insulated Slotted: 3.0, 4.5, 6.5mm
1000Volt
1000Volt
22 Pc. Pliers & Driver Set. Insulation According to VDE
0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. In molded tool box
Item# Set Includes: lbs. 8.70
9.0” Linemans Pliers W/Cutters 8.0” Long Nose Pliers W/Cutter
8.0” Diagonal Cutters 50mm Cable Stripping Knife
Insulated Slim Phillips: #1, 2 Insulated Slim Slotted: 3.5, 4.5mm
Insulated Slim Xeno: #1, 2 Insulated Slim Square: #1, 2
Insulated T-handle Hex Inch: 5/32, 3/16, 7/32, 1/4, 5/16, 3/8”
Insulated Inch Nut Drivers: 3/8, 7/16, 1/4, 5/16”
Now in
canvas
tool bag
10 Pc. Pliers & Driver Set. Insulation According to VDE
0682/part 201, EN/IEC 60900, ASTM F-1505, NFPA70E & CSA,
up to 1000 volt. Individually Tested. In canvas zipper pouch
Item# Set Includes: lbs. 5.74
8.0” Linemans Pliers 8.0” Long Nose Pliers W/Cutter
8.0” Diagonal Cutter 6.3” Wire Stripper
10.0” Adjustable Pliers
Insulated Phillips: #1, 2 Insulated Slotted: 3.0, 4.5, 6.5mm
1000Volt
32986
32986
32987
32987
32988
32988
32390
32390
32973
32973
32399
32399
Toll Free: (800) 494-6104
45
No Hassle Guarantee
Wiha branded tools are regarded as the most durable, best designed and highly innovative products
around. Our tools are used by demanding professional tradespeople and tool aficionados alike.
They are meant to be used and utilized often. However, if you are not happy for any reason return
them within 12 months of purchase with proof of purchase and we will Repair or Replace.
Rest assured, if for some reason there is a defect in material or workmanship we will replace your
tool free of charge for as long as you own the tool.
Failures due to misuse, abuse or normal wear and tear are not covered by this guarantee. We stand
by our products with what we believe is the best No Hassle Guarantee in the industry.
Exclusions
Wiha Tools has the right to exclude Bits, Tweezers and Ceramic Screwdrivers. These products are
either consumable or wear easily.
All torque tools are designed for 5,000 cycles or 1 year (whichever comes first). If a tool becomes
out of specification within that period Wiha Tools will Repair or Replace. Visit www.wihatools.com
to learn more about our Torque Control Service Program.
Legal
Some areas do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation or exclusion may not apply to you. This guarantee gives you specific rights, and you
may also have other rights, which vary, from state to state, province to province, or country to country.
This No Hassle Guarantee is the sole and exclusive guarantee for the Willi Hahn Corporation dba
Wiha Tools. No employee, agent, dealer, or other person is authorized to alter this guarantee or
make any other guarantees on behalf of Wiha Tools.
Willi Hahn Corporation USA
Attn: No Hassle Guarantee
1348 Dundas Circle
Monticello, MN 55362
800-494-6104
www.wihatools.com
Numerical Index by Item Number
46
10250 37
11950 13
11960 14
11975 14
11980 14
12326 13
12327 11
12851 10
12852 11
12853 13
12854 10
12855 10
12856 11
12857 11
12858 13
12859 13
13650 8
13651 8
13652 8
13653 8
13654 8
13655 8
13656 8
13657 8
13658 8
13659 8
13662 8
13663 8
13664 8
13665 8
13666 8
13667 8
13668 8
13669 8
13670 8
13671 8
13672 8
13673 8
13690 8
13691 8
13693 8
13694 8
15000 7
15003 7
15050 7
19767 13
20006 4
20007 4
20008 4
20009 4
20010 4
20011 4
20012 4
20013 4
20014 4
20015 4
20016 4
20017 4
20018 4
20019 4
20020 4
20022 4
20024 4
20027 4
20030 4
20032 4
20091 4
20093 4
20131 4
20133 4
20135 4
20136 4
20137 4
20138 4
20140 4
20141 4
20142 4
20144 4
20145 4
20146 4
20147 4
20148 4
20149 4
20151 4
20154 4
20190 4
20192 4
20194 5
20196 5
21008 6
21009 6
21010 6
21011 6
21012 6
21013 6
21014 6
21015 6
21017 6
21019 6
21020 6
21022 6
21024 6
21027 6
21030 6
21032 6
21040 6
21042 6
21044 6
21046 6
21048 6
21050 6
21052 6
21054 6
21056 6
21057 6
21058 6
21060 6
21062 6
21064 6
21066 6
21068 6
21093 6
21094 6
21095 6
21096 6
21103 38
21105 38
21208 5
21210 5
21212 5
21213 5
21214 5
21217 5
21219 5
21290 5
21325 5
21327 5
21329 5
21331 5
21333 5
21335 5
21391 5
25500 25
25511 25
28301 18
28302 17,18
28304 18
28307 19
28308 19
28309 19
28310 19
28312 19
28315 19
28317 19
28319 19
28320 19
28321 19
28327 19
28329 19
28330 19
28331 19
28332 19
28333 19
28334 19
28335 19
28336 19
28337 19
28338 19
28339 19
28340 19
28341 19
28342 19
28343 19
28344 19
28346 19
28347 19
28350 17
28366 17
28367 17
28368 17
28369 17
28371 17
28390 18
28391 18
28392 18
28393 17
28394 17
28395 17
28396 17
28398 18
28399 18
28724 17
28726 17
28727 17
28734 17
28736 17
28738 17
28740 16
28741 16
28742 16
28750 16
28751 16
28752 16
28791 16
28792 16
29006 10
29009 11
29012 13
29240 13
29250 13
30114 16
30138 16
30152 16
30190 16
30192 16
30700 25
30701 25
30711 25
30712 25
30746 20
30747 20
30770 21
31326 9
31327 9
31328 9
31329 9
31330 9
31331 9
31332 9
31333 9
31334 9
31335 9
31336 9
31337 9
31338 9
31339 9
31340 9
31341 9
31342 9
31343 9
31344 9
31345 9
31350 9
31390 9
31391 9
31394 10
31395 10
31425 10
31428 10
31429 10
31430 10
31431 10
31432 10
31433 10
31434 10
31435 10
31436 10
31437 10
31438 10
31439 10
31450 9
31460 9
31491 11
31493 11
31495 11
31496 11
31506 10
31507 10
31508 10
31509 10
31510 10
31511 10
31512 10
31513 10
31514 10
31515 10
31516 10
31517 10
31518 10
31519 10
31520 10
31521 10
31522 10
31524 10
31590 11
31592 11
31595 11
31608 12
31609 12
31610 12
31611 12
31612 12
31613 12
31614 12
31615 12
31616 12
31617 12
31618 12
31619 12
31620 12
31621 12
31622 12
31623 12
31624 12
31626 12
Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page
Toll Free: (800) 494-6104
47
Prop65 WARNING: This product
could expose you to Chrome 6, DEHP &
Phthalates. These chemicals are known to the
state of California to cause cancer. For more
information go to P65warnings.ca.gov/
32046 20
32049 20
32052 20
32055 20
32058 20
32079 21
32085 20
32087 25
32088 20
32089 25
32090 22
32091 23
32092 23
32093 23
32094 23
32095 23
32100 22
32101 22
32102 22
32103 22
32104 22
32105 22
32106 20
32107 20
32108 20
32145 20
32146 20
32188 23
32189 21
32190 23
32192 23
32196 21
32197 21
32198 21
32199 25
32206 26
32209 26
32212 26
32215 26
32218 26
32221 26
32224 26
32227 26
32230 26
32233 26
32236 26
32238 26
32239 26
32240 26
32241 26
32255 26
32258 26
32261 26
32264 26
32267 26
32268 26
32270 26
32273 26
32276 26
32278 26
32280 26
31627 12
31628 12
31630 12
31632 12
31650 9
31691 12
31694 12
31703 12
31704 12
31705 12
31707 12
31708 12
31709 12
31710 12
31712 12
31713 12
31714 12
31715 12
31716 12
31718 12
31720 12
31722 12
31790 12
31792 12
31805 9
31807 9
31809 9
31811 9
31813 9
31815 9
31817 9
31830 9
31832 9
31834 9
31836 9
31838 9
31840 9
31842 9
31844 9
31890 9
32000 20
32001 20
32002 20
32003 20
32004 20
32005 22
32010 22
32012 22
32015 22
32017 22
32023 22
32024 22
32025 22
32026 22
32027 22
32028 22
32031 22
32034 22
32039 22
32042 22
32045 22
32288 26
32291 26
32292 26
32293 26
32294 26
32296 26
32302 24
32303 24
32304 24
32305 24
32306 24
32308 24
32366 24
32390 44
32399 44
32400 25
32401 25
32402 25
32403 25
32505 24
32511 24
32512 20
32513 20
32514 20
32515 20
32516 24
32517 20
32518 20
32519 20
32521 24
32526 24
32531 24
32536 24
32541 24
32546 24
32551 24
32556 24
32561 24
32566 24
32590 24
32592 24
32596 21
32800 29
32801 29
32804 38
32806 38
32807 38
32808 38
32810 38
32814 36
32816 36
32818 36
32820 36
32821 36
32826 37
32828 37
32830 37
32831 36
32832 37
32833 35
32834 37
32835 37
32836 37
32837 35
32838 37
32841 36
32850 39
32852 39
32854 39
32856 34
32857 34
32858 34
32860 37
32861 37
32862 35
32863 35
32864 35
32865 34
32867 33
32868 33
32869 33
32870 38
32871 28
32872 28
32873 28
32874 31
32875 28
32876 30
32877 30
32878 31
32879 31
32886 28
32888 32
32889 33
32891 32
32892 32
32894 32
32895 32
32896 31
32899 33
32917 40
32923 40
32926 40
32927 41
32929 40
32930 41
32933 40
32936 42
32938 40
32939 40
32942 42
32944 41
32945 41
32947 41
32951 39
32954 39
32956 39
32973 44
32981 42
32982 43
32983 42
32984 42
Item No. Page Item No. Page Item No. Page Item No. Page Item No. Page
32985 43
32986 44
32987 44
32988 44
32989 43
32990 28
32999 43
33441 15
33443 15
33445 15
33447 15
33449 15
33478 15
33481 15
33482 15
33483 15
33485 15
33486 15
33487 15
33490 15
33532 22
33632 15
33634 15
33637 15
33641 15
35811 24
35812 24
35844 20
35845 20
35890 24
35891 24
38006 27
38007 27
38025 27
38050 27
38051 27
40800 13
61630 39
75205 14
75210 14
75215 14
75220 14
75302 14
75304 14
76208 7
76210 7
76212 7
76215 7
76290 7
91230 39
91256 38
www.wihatools.com
Catalog Item No. 99919
version - 2/1/18
To:
Insulation Test Cold Impact Test Material Integrity Test
Puncture Test Flame Resistance Test Adhesion Test
.wo
(800) 494-6104
fax: (800) 494-7456
cservice@wihatools.com
www.wihatools.com
Wiha Quality Tools
1348 Dundas Circle
Monticello, MN 55362
tel: 763.295.6591
fax: 763.295.6598
Wiha Tools Canada Ltd.
www.wihatools.ca
Brampton, ONT L6T 4X4
tel: 866.494.0096 or 763.295.6591
fax: 763.295.6598
Subject to change without notice
©2018 Willi Hahn Corporation
®Torx is a registered trademark of
Acument Intellectual Properties LLC.
99914.wo - TORX Catalog
99945.wo - ESD Catalog 99977.wo - Pliers/Crimpers Catalog
99934.wo - Hex Tools Catalog
99001.wo - TorqueControl Catalog
99951.wo - Bits Catalog 99002.wo - Screwdrivers Catalog
99004.wo - Shop Tools Catalog
99006.wo - Tech Tools Catalog
91330.wo - Tooling Catalog
