APU8836
1
Data and specifications subject to change without notice.
DESCRIPTION
The APU8836 device is an efficient linear voltage regula-
tor with better than 2% initial voltage accuracy, very low
dropout voltage and very low ground current designed
especially for hand held, battery powered applications.
Other features of the device are: TTL compatible enable/
shutdown control input, current limiting and thermal shut-
down.
The APU8836 is available in adjustable output
voltage versions in a small SOT-23 5-Pin package.
300mA ULTRA LOW DROPOUT POSITIVE
ADJUSTABLE AND FIXED REGULATORS
SOT-23-5 Package
Stable with 2.2mF Ceramic Capacitor
2% Voltage Reference Accuracy
Only 320mV Dropout at 300mA
and 170mV Dropout at 150mA
5mA Quiescent Current in Shutdown
Current Limit and Thermal Shutdown
Logic Input Enable Pin
Halogen Free & RoHS Compliant Product
TYPICAL APPLICATION
Figure 1 - Typical application of the APU8836 ajustable voltage regulator.
APPLICATIONS
Laptop, Notebook & Palmtop computers
Battery Powered Equipments
PCMCIA Vcc & Vpp Regulator
Consumer Electronics
High Efficiency Linear Power Supplies
FEATURES
PACKAGE ORDER INFORMATION
V
IN
V
O
R1
R2
C1
2.2uF C2
2.2uF
SD Enable
V
OUT
Adj
VIN
Gnd
EN
Vo = 0.8 3 1+ R1
R2
( )
Advanced Power
Electronics Corp.
200904104
APU8836X-HF
Y5 : SOT-23-5L
Package
Y5R : SOT-23-5L
Halogen Free
2
APU8836
ABSOLUTE MAXIMUM RATINGS
Input Voltage (VIN) ..................................................... 10V
Enable Input Voltage ................................................. 10V
Storage Temperature Range ....................................... -65°C To 150°C
Operating Junction Temperature Range ...................... 0°C To 150°C
PACKAGE INFORMATION
ELECTRICAL SPECIFICATIONS
Reference Voltage
Line Regulation
Load Regulation (Note 1)
Dropout Voltage (Note 2)
Ground Current (Note 3)
Ground Current-SD Activated
Current Limit
Thermal Regulation
Adjust Pin Current
Enable Pin Input LO Voltage
Enable Pin Input HI Voltage
Enable Pin Input LO Current
Enable Pin Input HI Current
Unless otherwise specified, these specifications apply over CIN=Co=2.2mF, Io=100mA, VIN(MIN)=2.5V(Adjustable
devices), VOUT=VFB(for adjustable version only), VEN=2V and TA=25oC. Typical values refer to TA=25oC.
Low duty cycle pulse testing is used which keeps junction and case temperatures equal to the ambient temperature.
PARAMETER SYM TEST CONDITION MIN TYP MAX UNITS
Vo + 1V<VIN<10V
1mA<Io<300mA
Io=100mA
Io=150mA
Io=300mA
VEN=2V, Io=1000mA
VEN=0V to 0.8V or Open
Vo=0V
VIN=10V, Io=150mA, 10ms Pulse
VIN=2.5V, Vo=VADJ
Regulator OFF
Regulator ON
VEN(L)=0V
VEN(H)=2V
-2
320
2
0.005
1.5
10
170
320
120
5
420
0.05
0.1
0.1
20
2
0.8
%
%/V
%
mV
mA
mA
mA
%/W
mA
V
V
mA
mA
Vo
DVI
DVL
DVI(O)
IQ
IQ(SD)
ICL
DVP
IADJ
VEN(L)
VEN(H)
Advanced Power
Electronics Corp.
ENGNDVIN
VOUT ADJ
TOP VIEW
Rthja=256/W
APU8836Y5
SOT-23-5L
EN GND VIN
VOUT
ADJ
TOP VIEW
Rthja=256/W
APU8836Y5R
SOT-23-5L
Junction Temperature Range ...................... 0oC To 125oC
APU8836
3
PIN SYMBOL PIN DESCRIPTION
The input pin of the regulator. Typically a large storage capacitor is connected from
this pin to ground to insure that the input voltage does not sag below the minimum
drop out voltage during the load transient response. This pin must always be higher
than VOUT by at least the amount of the dropout voltage and some margin in order for
the device to regulate properly.
Ground pin. This pin must be connected to the lowest potential in the system and all
other pins must be at higher potential with respect to this pin.
Enable pin. A low signal or left open on this pin shuts down the output. This pin must
be tied HI or to VIN for normal operation.
A resistor divider from this pin to the VOUT pin and ground sets the output voltage. To
minimize the error due to the error amplifier, select the values of the resistor dividers
to be less than 10KV.
The output of the regulator. A minimum of 2.2mF with max ESR of 1V capacitor must
be connected from this pin to ground to insure stability.
Note 3: Ground current is the regulator quiescent cur-
rent plus the pass transistor current. The total current
from the supply is the sum of the load current plus the
ground pin current.
Note 1: Low duty cycle pulse testing with Kelvin con-
nections is required in order to maintain accurate data.
Note 2: Dropout voltage is defined as the minimum dif-
ferential voltage between VIN and VOUT required to main-
tain regulation at VOUT. It is measured when the output
voltage drops below its nominal value.
PIN DESCRIPTIONS
VIN
Gnd
En
Adj
(Adjustable Only)
VOUT
Advanced Power
Electronics Corp.
4
APU8836
BLOCK DIAGRAM
Figure 2 - APU8836 Adjustable output block diagram.
V
IN
En
THERMAL
SHUTDOWN
0.8V
V
OUT
Adj
Gnd
+
Advanced Power
Electronics Corp.
CURRENT
LIMIT
Advanced Power
Electronics Corp. APU8836
TYPICAL PERFORMANCE CHARACTERISTICS
VIN=VEN=3.5V, R1/R2=2K/1K, CIN=COUT=2.2uF(EL Cap.)
VIN=VEN=3.5V, R1/R2=2K/1K, CIN=COUT=2.2uF(EL Cap.)
Power ON (RL=8) Power OFF (RL=8)
Power ON (RL=16) Power OFF (RL=16)
Power Sequence
5
IOUT=0mA ~ 150mA
VIN=3.5V, R1/R2=2K/1K, CIN=COUT=2.2uF(EL Cap.) VIN=3.5V, R1/R2=2K/1K, CIN=COUT=2.2uF(EL Cap.)
Ton=Toff=1mS, Rising=Falling=0.25A/uS
Current Limit (VOUT vs. IOUT)Load Transient
Power Sequence
VOUT
IOUT
VOUT
IOUT
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
Advanced Power
Electronics Corp. APU8836
TYPICAL PERFORMANCE CHARACTERISTICS
VIN=3.5V, R1/R2=2K/1K, CIN=COUT=2.2uF(EL Cap.)
VEN=0V to 2V VEN=2V to 0V
VIN=3.5V, R1/R2=2KΩ/1KΩ, CIN=COUT=2.2uF(EL Cap.)
VEN=0V to 2V VEN=2V to 0V
6
Enable ON Sequence (RL=16) Enable OFF Sequence (RL=16)
Enable ON Sequence (RL=8) Enable OFF Sequence (RL=8)
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
VIN
VEN
VOUT
IOUT
Package Outline : SOT-23-5L
MIN NOM MAX
A 1.00 1.10 1.30
A1 0.00 --- 0.10
A2 0.70 0.80 0.90
b 0.30 0.40 0.50
C 0.10 0.15 0.25
D 2.70 2.90 3.10
E 1.40 1.60 1.80
e --- 1.90(TYP) ---
H 2.60 2.80 3.00
L 0.37 --- ---
θ10° 5° 9°
e1 --- 0.95(TYP) ---
Note 1Package Body Sizes Exclude Mold Flash Protrusions or Gate Burrs.
Note 2Tolerance ± 0.1000 mm(4mil) Unless Otherwise Spe- cified.
Note 3Coplanarity0.1000 mm
Note 4Dimension L Is Measured in Gage plane.
Part Marking Information & Packing : SOT-23-5L
ADVANCED POWER ELECTRONICS CORP.
SYMBOLS Millimeters
XSSS
Part Number : XS
Date Code : SS
SS:2004,2008,2012…
SS:2003,2007,2011…
SS:2002,2006,2010…
SS:2001,2005,2009…
7
RS : APU8836Y5
rS : APU8836Y5R