HLMP-6300-F00XX - Agilent / Hewlett-Packard

HLMP-Pxxx Series, HLMP-Qxxx Series

HLMP-6xxx Series, HLMP-70xx Series

Agilent HLMP-Pxxx

Subminiature LED Lamps

Data Sheet

Features

•Subminiature flat top package

– ideal for backlighting and light

piping applications

•Subminiature dome package

– diffused dome for wide viewing

angle

– nondiffused dome for high

brightness

•TTL and LSTTL compatible 5 volt

resistor lamps

•Available in six colors

•Ideal for space limited

applications

•Axial leads

•Available with lead configurations

for surface mount and through

hole PC board mounting

Description

Flat Top Package

The HLMP-Pxxx Series flat top

lamps use an untinted, non-

diffused, truncated lens to

provide a wide radiation pattern

that is necessary for use in

backlighting applications. The

flat top lamps are also ideal for

use as emitters in light pipe

applications.

Dome Packages

The HLMP-6xxx Series dome

lamps for use as indicators use a

tinted, diffused lens to provide a

wide viewing angle with a high

on-off contrast ratio. High

brightness lamps use an

untinted, nondiffused lens to

provide a high luminous

intensity within a narrow

radiation pattern.

Resistor Lamps

The HLMP-6xxx Series 5 volt

subminiature lamps with built in

current limiting resistors are for

use in applications where space

is at a premium.

Lead Configurations

All of these devices are made by

encapsulating LED chips on

axial lead frames to form molded

epoxy subminiature lamp

packages. A variety of package

configuration options is avail-

able. These include special

surface mount lead configura-

tions, gull wing, yoke lead or

Z-bend. Right angle lead bends

at 2.54 mm (0.100 inch) and

5.08 mm (0.200 inch) center

spacing are available for through

hole mounting. For more

information refer to Standard

SMT and Through Hole Lead

Bend Options for Subminiature

LED Lamps data sheet.

Device Selection Guide

Part Number: HLMP-xxxx

DH AS High High Device

Standard AlGaAs Efficiency Perf. Emerald Outline

Red Red Red Orange Yellow Green Green Device Description[1] Drawing

P005 P105 P205 P405 P305 P505 P605 Untinted, Nondiffused, A

Flat Top

P102 P202 P402 P302 P502 Untinted, Diffused, Flat Top A

6000 Q100 6300 Q400 6400 6500 Q600 Tinted, Diffused B

Q105 6305 Q405 6405 6505 Q605 Untinted, Nondiffused, B

High Brightness

Q150 7000 7019 7040 Tinted, Diffused, Low Current B

Q155 Nondiffused, Low Current B

6600 6700 6800 Tinted, Diffused, Resistor, B

5 V, 10 mA

6620 6720 6820 Diffused, Resistor, 5 V, 4 mA B

Ordering Information

HLMX-XXXX-X X X X X

4 x 4 Prod.

Part

Number

Min. Iv Bin

Max. Iv Bin

Color Bin

Selection

Packaging

Option

0.50 (0.020) REF.

0.94

1.24 (0.037)

(0.049)

2.92 (0.115)

MAX.

0.76

0.89 (0.030)

(0.035)R.

0.63

0.38(0.025)

(0.015)

2.03 (0.080)

1.78 (0.070)

0.79 (0.031)

0.53 (0.021)

0.46

0.56(0.018)

(0.022)

0.25 (0.010) MAX.

NOTE 2

0.20 (0.008) MAX.

CATHODE

1.65

1.91(0.065)

(0.075)DIA.

ANODE

11.68

10.67(0.460)

(0.420)

BOTH SIDES

0.18

0.23(0.007)

(0.009)

2.08

2.34(0.082)

(0.092)

CATHODE

STRIPE

2.21

1.96(0.087)

(0.077)

(B) Diffused and Nondiffused

Figure 1. Proper right angle mounting to a PC board to prevent protruding cathode tab from shorting to anode connection.

Package Dimensions

(A) Flat Top Lamps

NO. ANODE DOWN. YES. CATHODE DOWN.

CATHODE

TAB

NOTES:

1. ALL DIMENSIONS ARE IN MILLIMETRES (INCHES).

2. PROTRUDING SUPPORT TAB IS CONNECTED TO CATHODE LEAD.

3. LEAD POLARITY FOR AlGaAs LAMPS IS OPPOSITE TO THE LEAD

POLARITY OF SUBMINIATURE LAMPS USING OTHER TECHNOLOGIES.

0.46

0.56 (0.018)

(0.022)

1.40

1.65(0.055)

(0.065)

0.25 (0.010) MAX.

NOTE 2

0.20 (0.008) MAX.

0.50 (0.020) REF.

CATHODE

1.65

1.91(0.065)

(0.075)DIA.

ANODE

11.68

10.67(0.460)

(0.420)

BOTH SIDES

1.14

1.40 (0.045)

(0.055) 0.63

0.38 (0.025)

(0.015)

2.21

1.96(0.087)

(0.077)

0.18

0.23(0.007)

(0.009)

0.79 (0.031) MAX.

2.44

1.88(0.096)

(0.074)

2.08

2.34(0.082)

(0.092)

CATHODE

STRIPE

Absolute Maximum Ratings at TA = 25°C

DH AS High

Standard AlGaAs Eff. High Perf. Emerald

Parameter Red Red Red Orange Yellow Green Green Units

DC Forward Current[1] 50 30 30 30 20 30 30 mA

Peak Forward Current[2] 1000 300 90 90 60 90 90 mA

DC Forward Voltage 6 6 6 6 V

(Resistor Lamps Only)

Reverse Voltage (IR = 100 µA) 5 5 5 5 5 5 5 V

Transient Forward Current[3] 2000 500 500 500 500 500 500 mA

(10 µs Pulse)

Operating Temperature Range:

Non-Resistor Lamps -55 to +100 -40 to +100 55 to +100 -40 to +100 -20 to +100 °C

Resistor Lamps -40 to +85 -20 to +85

Storage Temperature Range -55 to +100 °C

For Thru Hole Devices 260°C for 5 seconds

Wave Soldering Temperature

[1.6 mm (0.063 in.) from body]

For Surface Mount Devices: 260°C for 20 seconds

Reflow Soldering Temperature

Notes:

1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.

2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.

3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this

high current.

Electrical/Optical Characteristics, TA = 25°C

Standard Red

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

6000-E00xx 0.63 1.2

6000-G00xx Luminous Intensity[1] IV1.60 3.2 mcd IF = 10 mA

P005-F00xx 1.0 2.5

Forward Voltage VF1.4 1.6 2.0 V IF = 10 mA

All Reverse Breakdown VR5.0 12.0 V IR = 100 µA

Voltage

6000 Included Angle Between 2q1/290 Deg.

P005 Half Intensity Points[2] 125

Peak Wavelength lPEAK 655 nm

Dominant Wavelength[3] ld640 nm

Spectral Line Half Width Dl1/2 24 nm

All Speed of Response ts15 ns

Capacitance C 100 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hv65 lm/W

DH AS AlGaAs Red

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P102-F00xx 1.0 20.0

P105-L00xx 10.0 30.0

P105-NP000 25 80

Q100-M00xx 16 45

Q100-N00xx Luminous Intensity IV25.0 45.0 mcd IF = 20 mA

Q100-PQ000 40 125

Q105-P00xx 40 200

Q105-ST000 160 500

Q150-F00xx 1.0 1.8 IF = 1 mA

Q155-F00xx 1.0 4.0

Q100 Forward Voltage VF1.8 2.2 VIF = 20 mA

Q150/Q155 1.6 1.8 IF = 1 mA

All Reverse Breakdown Voltage VR5.0 15.0 V IR = 100 µA

P105 125

Q100/Q150 Included Angle Between 2q1/290 Deg.

Q105/Q155 Half Intensity Points[2] 28

Peak Wavelength lPEAK 645 nm Measured at Peak

Dominant Wavelength[3] ld637 nm

Spectral Line Half Width Dl1/2 20 nm

All Speed of Response ts30 ns Exponential Time

Constant; e-t/ts

Capacitance C 30 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to Cathode Lead

Luminous Efficacy[4] hv80 lm/W

High Efficiency Red

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P202-F00xx 1.0 5.0

P205-F00xx 1.0 8.0

P205-JK000 4.0 12.5 IF = 10 mA

6300-F00xx 1.0 10.0

6300-KL000 Luminous Intensity[1] IV6.3 20.0 mcd

6305-L00xx 10.0 40.0

7000-D00xx 0.4 1.0 IF = 2 mA

6600-G00xx 1.6 5.0 VF = 5.0 Volts

6620-F00xx 1.0 2.0

All Forward Voltage VF1.5 1.8 3.0 V IF = 10 mA

(Nonresistor Lamps)

6600 Forward Current IF9.6 13.0 mA VF = 5.0 V

6620 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown Voltage VR5.0 30.0 V IR = 100 µA

P205 125

6305 Included Angle Between 2q1/228 Deg.

All Diffused Half Intensity Points[2] 90

Peak Wavelength lPEAK 635 nm Measured at Peak

Dominant Wavelength[3] ld626 nm

Spectral Line Half Width Dl1/2 40 nm

All Speed of Response ts90 ns

Capacitance C 11 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hv145 lm/W

Orange

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P402-F00xx 1.0 4.0

P405-F00xx 1.0 6

P405-JK000 Luminous Intensity IV4.0 12.5 mcd IF = 10 mA

Q400-F00xx 1.0 8

Q405-H00xx 2.5 14

All Forward Voltage VF1.5 1.9 3.0 V IF = 10 mA

Reverse Breakdown Voltage VR5.0 30.0 V IR = 100 µA

P40x Included Angle Between 2q1/2125 Deg.

Q40x Half Intensity Points[2] 90

Peak Wavelength lPEAK 600 nm

Dominant Wavelength[3] ld602 nm Measured at Peak

Spectral Line Half Width Dl1/2 40 nm

All Speed of Response ts260 ns

Capacitance C 4 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hv380 lm/W

Yellow

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P302-F00xx 1.0 3.0

P305-F00xx 1.0 4.0

6400-F00xx 1.0 9.0

6400-JK000 4.0 12.5 IF = 10 mA

6405-J00xx Luminous Intensity[1] IV3.6 20 mcd

6405-MN0xx 16 50

7019-D00xx 0.4 0.6 IF = 2 mA

6700-G00xx 1.4 5.0 VF = 5.0 Volts

6720-F00xx 0.9 2.0

All Forward Voltage VF2.0 2.4 V IF = 10 mA

(Nonresistor Lamps)

6700 Forward Current IF9.6 13.0 mA VF = 5.0 V

6720 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown VR5.0 50.0 V

Voltage

P305 Included Angle Between 125

6405 Half Intensity Points[2] 2q1/228 Deg.

All Diffused 90

Peak Wavelength lPEAK 583 nm Measured at Peak

Dominant Wavelength[3] ld585 nm

Spectral Line Half Width Dl1/2 36 nm

All Speed of Response ts90 ns

Capacitance C 15 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hv500 lm/W

High Performance Green

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P502-F00xx 1.0 3.0

P505-G00xx 1.6 6.3 IF = 10 mA

6500-F00xx 1.0 7.0

6505-L00xx Luminous Intensity[1] Iv10.0 40.0 mcd

7040-D00xx 0.4 0.6 IF = 2 mA

6800-G00xx 1.6 5.0 VF = 5.0 Volts

6820-F00xx 1.0 2.0

All Forward Voltage VF2.1 2.7 V IF = 10 mA

(Nonresistor Lamps)

6800 Forward Current IF9.6 13.0 mA VF = 5.0 V

6820 (Resistor Lamps) 3.5 5.0

All Reverse Breakdown Voltage VR5.0 50.0 V IR = 100 µA

P505 Included Angle Between 125

6505 Half Intensity Points[2] 2q1/228 Deg.

All Diffused 90

Peak Wavelength lPEAK 565 nm

Dominant Wavelength[3] ld569 nm

Spectral Line Half Width Dl1/2 28 nm

All Speed of Response ts500 ns

Capacitance C 18 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hv595 lm/W

Notes:

1. The luminous intensity for arrays is tested to assure a 2.1 to 1.0 matching between elements. The average luminous intensity for an array

determines its light output category bin. Arrays are binned for luminous intensity to allow Iv matching between arrays.

2. q1/2 is the off-axis angle where the luminous intensity is half the on-axis value.

3. Dominant wavelength, ld, is derived from the CIE Chromaticity Diagram and represents the single wavelength that defines the color of the device.

4. Radiant intensity, Ie, in watts/steradian, may be calculated from the equation Ie = Iv/hv, where Iv is the luminous intensity in

candelas and hv is the luminous efficacy in lumens/watt.

Emerald Green[1]

Device

HLMP- Parameter Symbol Min. Typ. Max. Units Test Conditions

P605-F00xx 1.0 1.5

Q600-F00xx Luminous Intensity IV1.0 1.5 mcd IF = 10 mA

Q605-F00xx 1.0 7.5

All Forward Voltage VF2.2 3.0 V IF = 10 mA

Reverse Breakdown Voltage VR5.0 V IR = 100 µA

P605 Included Angle Between 2q1/2125 Deg.

Q60x Half Intensity Points[2] 90

Peak Wavelength lPEAK 558 nm

Dominant Wavelength[3] ld560 nm Measured at Peak

Spectral Line Half Width Dl1/2 24 nm

P605/Q600 Speed of Response ts3100 ns

Capacitance C 35 pF VF = 0; f = 1 MHz

Thermal Resistance RqJ-PIN 170 °C/W Junction-to-Cathode Lead

Luminous Efficacy[4] hV656 lm/W

Note:

1. Please refer to Application Note 1061 for information comparing standard green and emerald green light output degradation.

Standard Red, DH As AlGaAs Red

Standard Red and DH AS

AlGaAs Red High Efficiency Red, Orange,

Yellow, High Performance

Green, and Emerald Green

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

Low Current

Figure 1. Relative intensity vs. wavelength.

Figure 2. Forward current vs. forward voltage (non-resistor lamp).

Figure 3. Relative luminous intensity vs. forward current (non-resistor lamp).

FORWARD CURRENT – mA

100

FORWARD VOLTAGE – V

0.5 1 1.5 2 2.5 3 3.5

HIGH

PERFORMANCE

GREEN,

EMERALD

GREEN

YELLOW

HIGH EFFICIENCY

RED/ORANGE

Figure 4. Relative efficiency (luminous intensity per unit current) vs. peak current (non-resistor lamps).

Figure 5. Maximum forward dc current vs. ambient temperature. Derating based on TJ MAX = 110°C (non-resistor lamps).

Figure 6. Maximum tolerable peak current vs. pulse duration (IDC MAX as per MAX ratings) (non-resistor lamps).

Standard Red

DH As AlGaAs RedStandard Red

HER, Orange, Yellow, and High

Performance Green DH As AlGaAs Red

HER, Orange, Yellow, and

High Performance Green,

and Emerald Green

Figure 9. Relative intensity vs. angular displacement.

Figure 7. Resistor lamp forward current vs. forward voltage. Figure 8. Resistor lamp luminous intensity vs. forward voltage.

Intensity Bin Limits

Bin Min. Max.

A 0.10 0.20

B 0.16 0.32

C 0.25 0.50

D 0.40 0.80

E 0.63 1.25

F 1.00 2.00

G 1.60 3.20

H 2.50 5.00

J 4.00 8.00

K 6.30 12.50

L 10.00 20.00

M 16.00 32.00

N 25.00 50.00

P 40.00 80.00

Q 63.00 125.00

R 100.00 200.00

S 160.00 320.00

T 250.00 500.00

U 400.00 800.00

V 630.00 1250.00

W 1000.00 2000.00

X 1600.00 3200.00

Y 2500.00 5000.00

Color Bin Limits

Package Bin Min. Max.

Emerald Green 0 Full Distribution

9 552 556

8 555 559

7 558 562

6 561 565

Green 0 Full Distribution

6 561 565

5 564 568

4 567 571

3 570 574

2 573 577

Yellow 0 Full Distribution

1 581.5 585.0

3 584.0 587.5

2 586.5 590.0

4 589.0 592.5

5 591.5 593.5

6 591.5 595.0

7 594.0 597.5

Orange 0 Full Distribution

1 596.5 600.0

2 599.0 602.5

3 601.5 604.0

4 603.8 608.2

5 606.8 611.2

6 609.8 614.2

7 612.8 617.2

8 615.8 620.2

Ordering Information

HLMx-XXXX-X X X X X

4 x 4 Prod.

Part

Number

Min. Iv Bin

Max. Iv Bin

Color Bin

Selection

Packaging

Option

Mechanical Option

00 Straight Leads, Bulk Packaging, Quantity of 500 Parts

10 Right Angle Housing, Bulk Packaging, Quantity of 500 Parts

11 Gull Wing Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

12 Gull Wing Lead, Bulk Packaging, Quantity of 500 Parts

14 Gull Wing Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

21 Yoke Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

22 Yoke Leads, Bulk Packaging, Quantity of 500 Parts

24 Yoke Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

31 Z-Bend Leads, 12 mm Tape on 7 in. Dia. Reel, 1500 Parts per Reel

32 Z-Bend Leads, Bulk Packaging, Quantity of 500 Parts

34 Z-Bend Leads, 12 mm Tape on 13 in. Dia. Reel, 6000 Parts per Reel

1L 2.54 mm (0.100 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)

1S 2.54 mm (0.100 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)

2L 5.08 mm (0.200 inch) Center Lead Spacing, Long Leads; 10.4 mm (0.410 in.)

2S 5.08 mm (0.200 inch) Center Lead Spacing, Short Leads; 3.7 mm (0.145 in.)

Note:

All Categories are established for classification of products. Products may not be available in all categories.

Please contact your local Agilent representative for further clarification/information.

www.agilent.com/semiconductors

For product information and a complete list of

distributors, please go to our web site.

For technical assistance call:

Americas/Canada: +1 (800) 235-0312 or

(916) 788-6763

Europe: +49 (0) 6441 92460

China: 10800 650 0017

Hong Kong: (+65) 6756 2394

India, Australia, New Zealand: (+65) 6755 1939

Japan: (+81 3) 3335-8152(Domestic/Interna-

tional), or 0120-61-1280(Domestic Only)

Korea: (+65) 6755 1989

Singapore, Malaysia, Vietnam, Thailand,

Philippines, Indonesia: (+65) 6755 2044

Taiwan: (+65) 6755 1843

Data subject to change.

Obsoletes 5988-6260EN

October 19, 2004

5989-1708EN