Siemens AG
Industry Sector
Postfach 48 48
90026 NÜRNBERG
GERMANY
Order number: C79000-G8976-C174
Ⓟ 07/2013 Technical data subject to change
Copyright © Siemens AG 2008 - 2013.
All rights reserved
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.
Preface
Overview
Information on this document
This document provides you with information on the current products and on products that
were previously available along with their versions and a brief description of the product.
CP documentation
You will find the documentation for the SIMATIC NET S7 CP here:
● Depending on the shipment package, on the manual DVD supplied with the device or the
product CD / product DVD
● On the pages of Product Support on the Internet
(http://support.automation.siemens.com/ww/view/en/10805878)
Go to the required product group and make the following settings:
"Entry list" tab, Entry type "Manuals"
Structure of the documentation
There is a table for each module that informs you of the current version of the module and a
second table that lists the previously available versions.
Layout of the tables / example:
Device data
Order numbers / versions Characteristics
STEP 7 version
required (for full
functionality)
Order number:
6GK7...
Hardware product version: X
Firmware version: Y
Relevant documentation
Manual ....
Entry ID: 123456 http://www...
Extended functionality compared with the
previous hardware product version:
...
• STEP 7 Vx.y
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 3
Preface
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
4 Reference Manual, 07.2013, C79000-G8976-C174-22
Notes for the reader
The meaning of the table columns is as follows:
● "Order numbers / versions" column
The column contains the following information:
– Current hardware product version and current firmware version. If a firmware update is
available, the download address is shown.
– Download address of the documentation and "SIMATIC NET Updates" entries. The
numeric string is the relevant entry ID.
● "Characteristics / new or modified functions" column
Here, you will find an overview of the following:
– The essential performance characteristics of new modules;
– For modified modules, the changed characteristics or bugs fixed.
● "STEP 7 version required (for full functionality)" column
The STEP 7 version required for configuration. This is the STEP 7 version as of which all
performance characteristics of the module version described can be used.
The very latest documentation is available on the Internet!
The latest descriptions of the current products are always available on the Internet under the
entry IDs or on the Internet pages listed here and in the tables following.
Manuals on the STEP 7 configuration tool can be found under the following entry IDs:
● Configuring and commissioning S7 CPs for PROFIBUS
1158693 (http://support.automation.siemens.com/ww/view/en/1158693)
● Functions (FC) and Function Blocks (FB) for SIMATIC NET S7 CPs
30564821 (http://support.automation.siemens.com/ww/view/de/30564821)
Downloads of the current versions of the program blocks
For new user programs, always use the current program block versions. You will find
information on the current program block versions and can download the current SIMATIC
NET program blocks from the Internet under the following Entry ID:
8797900 (http://support.automation.siemens.com/WW/view/de/8797900)
If you are replacing a CP, please follow the instructions in the relevant manual (refer to
"Further information").
Current version history
You will find the latest version history for S7 CPs as well as this version history for SIMATIC
NET blocks under the following Entry ID:
9836605 (http://support.automation.siemens.com/WW/view/de/9836605)
Preface
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 5
Further information
If you require descriptions of the older versions, please contact your Siemens representative
quoting the relevant product name.
Preface
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
6 Reference Manual, 07.2013, C79000-G8976-C174-22
Table of contents
Preface ...................................................................................................................................................... 3
1 SIMATIC S7-300........................................................................................................................................ 9
1.1 CP 342-5 / CP 342-5 FO................................................................................................................9
1.1.1 Current version CP 342-5 ..............................................................................................................9
1.1.2 Current version CP 342-5 FO ......................................................................................................10
1.1.3 Predecessor modules / predecessor versions.............................................................................11
1.2 CP 343-5......................................................................................................................................21
1.2.1 Current version.............................................................................................................................21
1.2.2 Previous versions.........................................................................................................................22
1.2.3 Predecessor modules ..................................................................................................................26
2 SIMATIC S7-400...................................................................................................................................... 27
2.1 CP 443-5 Basic ............................................................................................................................27
2.1.1 Current version.............................................................................................................................27
2.1.2 Previous versions.........................................................................................................................28
2.1.3 Predecessor modules ..................................................................................................................29
2.2 CP 443-5 Extended......................................................................................................................32
2.2.1 Current version.............................................................................................................................32
2.2.2 Previous versions.........................................................................................................................33
2.2.3 Predecessor modules ..................................................................................................................34
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 7
Table of contents
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
8 Reference Manual, 07.2013, C79000-G8976-C174-22
SIMATIC S7-300 1
1.1 CP 342-5 / CP 342-5 FO
1.1.1 Current version CP 342-5
Characteristic data of the device
Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order numbers / versions
Order number:
6GK7 342-5DA03-0XE0
Hardware product version: 2
Firmware version: V6.0
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section:
as of release 05 - 09/2011
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
as of release 09 - 10/2011
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
Hardware modification:
• Due to production, no functional
modifications compared with the
previous version.
The firmware version is unchanged and
therefore compatible and can be used
with hardware product versions 1 and 2
STEP 7
• STEP 7 as of version V5.5 SP2
• STEP 7 as of version V5.4 SP5 with
HSP 1049
STEP 7 Professional
• STEP 7 V11.0
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 9
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
10 Reference Manual, 07.2013, C79000-G8976-C174-22
1.1.2 Current version CP 342-5 FO
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 342-5DF00-0XE0
Hardware product version: 5
Firmware version: V5.7
The firmware can be obtained at:
24105718
(http://support.automation.siemens.com
/ww/view/de/24105718)
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET updates with firmware
release:
24104930
(http://support.automation.siemens.com
/ww/view/de/24104930)
Firmware modification:
• Bugs fixed, no functional
modifications compared with the
previous firmware version.
The firmware version is compatible and
can be used with hardware product
versions 1, 3 and 4, 5, 6
STEP 7
• STEP 7 Version V5.1 SP2 or higher
You configure the CP as firmware
version V5.0.
STEP 7 Professional
• STEP 7 Professional Version V11.0
or higher
You configure the CP as firmware
version V5.0.
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 11
1.1.3 Predecessor modules / predecessor versions
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 342-5DA03-0XE0
Hardware product version: 1
Firmware version: V6.0
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section:
as of release 05 - 09/2011
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
as of release 09 - 10/2011
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET updates with hardware
release:
24104930
(http://support.automation.siemens.com
/ww/view/de/24104930)
The CP 342-5 (6GK7 342-5DA03-
0XE0) is suitable as a replacement for
the following predecessor products:
• CP 342-5 (6GK7 342-5DA00-0XE0)
• CP 342-5 (6GK7 342-5DA01-0XE0)
• CP 342-5 (6GK7 342-5DA02-0XE0)
Additional functional characteristics:
• The CP supports SYNC / FREEZE
in DP slave mode.
Please refer to the information on
compatibility in the current manual.
STEP 7
• STEP 7 as of version V5.5 SP2
• STEP 7 as of version V5.4 SP5 with
HSP 1049
STEP 7 Professional
• STEP 7 V11.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
12 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
Hardware product version: 6
Firmware version: V5.7
The firmware can be obtained at:
24105718
(http://support.automation.siemens.com
/ww/view/de/24105718)
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET updates with firmware
release:
24104930
(http://support.automation.siemens.com
/ww/view/de/24104930)
Firmware modification:
• Bugs fixed, no functional
modifications compared with the
previous firmware version.
The firmware version is compatible and
can be used with hardware product
versions 1, 3 and 4, 5, 6
STEP 7
• STEP 7 Version V5.1 SP2 or higher
You configure the CP as firmware
version V5.0.
STEP 7 Professional
• STEP 7 Professional Version V11.0
or higher
You configure the CP as firmware
version V5.0.
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 13
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
Hardware product version: 6
6GK7 342-5DF00-0XE0
Hardware product version: 5
Firmware version: V5.6
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/de/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
Hardware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is unchanged and therefore
compatible and can be used with hardware product
versions 1, 3 and 4, 5, 6
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
14 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
Hardware product version: 5
6GK7 342-5DF00-0XE0
Hardware product version: 4
Firmware version: V5.6
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/de/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
Firmware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is compatible and can be used
with hardware product versions 1, 3 and 4, 5
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 15
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
Hardware product version: 5
6GK7 342-5DF00-0XE0
Hardware product version: 4
Firmware version: V5.5
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/de/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET updates with firmware
release:
22794601
(http://support.automation.siemens.com
/ww/view/de/22794601)
Firmware modification:
• Enhanced functions:
The routing of PG connections is now also possible
with the CP in STOP mode;
• Bugs fixed (for example in the CP functions: S7
routing; online/offline block comparison in the
SIMATIC Manager; download of configurations;
stability if disruptions occur on PROFIBUS);
The firmware version is compatible and can be used
with hardware product versions 1, 3 and 4, 5
Hardware modification for 6GK7 342-5DA02-0XE0:
The change in the version is only due to production
and does not represent any change in function.
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
16 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 4
Firmware version: V5.4
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 02/2003
• General section:
1158693
(http://support.automation.siemens.com
/ww/view/de/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET update with CP release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
SIMATIC NET updates with firmware
release:
19726245
(http://support.automation.siemens.com
/ww/view/de/19726245)
Firmware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is compatible and can be used
with hardware product versions 1, 3 and 4
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 17
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 4
Firmware version: V5.2
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 04 - 2/2003
• General section
1158693
(http://support.automation.siemens.com
/ww/view/de/1158693)
• Part specific to the CP 342-5 / CP
342-5 FO
8773570
(http://support.automation.siemens.com
/ww/view/de/8773570)
SIMATIC NET updates with firmware
release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
14222660
(http://support.automation.siemens.com
/ww/view/de/14222660)
Firmware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is compatible and can be used
with hardware product versions 1, 3 and 4
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 4
Firmware version: V5.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
SIMATIC NET update with CP release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
10605200
(http://support.automation.siemens.com
/ww/view/de/10605200)
Hardware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is unchanged and therefore
compatible and can be used with hardware product
versions 1, 3 and 4
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
18 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 3
Firmware version: V5.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
SIMATIC NET update with CP release:
12324024
(http://support.automation.siemens.com
/ww/view/de/12324024)
Hardware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is unchanged and therefore
compatible and can be used with hardware product
versions 1 and 3
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 2
Firmware version: V5.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET update with CP release:
10605200
(http://support.automation.siemens.com
/ww/view/de/10605200)
10604648
(http://support.automation.siemens.com
/ww/view/de/10604648)
Extended functionality compared with the previous
firmware version:
- none; bug fixes only -
• compatible and usable with hardware product
versions 1 and 2
Hardware modification:
• due to production, functionally compatible with
predecessor version
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V5.0
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 1
Firmware version: V5.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET updates with firmware
release:
8928271
(http://support.automation.siemens.com
/ww/view/de/8928271)
The CP 342-5 can be used as a replacement for the
following previous products:
CP 342-5 order no.: 6GK7 342-5DA00-0XE0
CP 342-5 order no.: 6GK7 342-5DA01-0XE0
The CP 342-5 and CP 342-5 FO named here are
functionally compatible.
Extended functionality compared with the previous
firmware version:
• Multiplexing OP connections
• S7 communication via loadable communication
blocks (client function)
• Extensive S7 connection diagnostics
STEP 7 Version V5.1
SP2 or higher
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 19
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 1
Firmware version: V4.1
Relevant documentation:
S7 CPs for PROFIBUS manual
no change compared with firmware
version V4.0
SIMATIC NET updates with firmware
release:
6567193
(http://support.automation.siemens.com
/ww/view/de/6567193)
Extended functionality compared with the previous
firmware version:
- none; bug fixes only -
STEP 7 Version V5.1 or
higher
can be configured as
firmware version V4.0
Order number:
6GK7 342-5DA02-0XE0
6GK7 342-5DF00-0XE0
Hardware product version: 1
Firmware version: V4.0
Relevant documentation:
Manual
CP 342-5 / CP 342-5 FO
(included on the S7 CP Documentation
CD 10/2000)
SIMATIC NET update with CP release:
4893757
(http://support.automation.siemens.com
/ww/view/de/4893757)
4894043
(http://support.automation.siemens.com
/ww/view/de/4894043)
Extended functionality compared with previous
product (6GK7-342-5DA01-0XE0):
• The transmission speeds are also supported:
3, 6, 12 Mbps
• extended I/O configuration limits
• additional CP variant with integrated fiber-optic
connector
Additional feature: single module width (predecessor
double width)
STEP 7 Version V5.1 or
higher
SIMATIC S7-300
1.1 CP 342-5 / CP 342-5 FO
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
20 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7-342-5DA01-0XE0
Hardware product version: 2
Firmware version: V3.00
The firmware can be obtained at:
753015
(http://support.automation.siemens.com
/ww/view/de/753015)
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
Product information bulletin CP 342-5
Document no.: C79000-Z8964-C032-
03
SIMATIC NET update with CP release:
4245051
(http://support.automation.siemens.com
/ww/view/de/4245051)
Extended functionality compared with previous
product CP 342-5 (6GK7 342-5DA00-0XE0):
• Firmware loader
• Distribution of bus parameters
• Replacing a module without a programming device
• Routing of PG functions
STEP 7 Version V5.0 or
higher
Order number:
6GK7-342-5DA00-0XE0
Hardware product version: 13
Firmware version: V 1.50
The firmware: You will find information
about the SIM package 287 at:
4245101
(http://support.automation.siemens.com
/ww/view/de/4245101)
The GSD file can be obtained at:
113652
(http://support.automation.siemens.com
/ww/view/de/113652)
Relevant documentation:
Product information bulletin CP 342-5
Document no.: C79000-Z8964-C021-
07
SIMATIC NET update with CP release:
4245101
(http://support.automation.siemens.com
/ww/view/de/4245101)
Basic functionality with:
• PROFIBUS-DP as DP master or DP slave
• S5-compatible communication via FDL
connections
• S7 communication
STEP 7 Version V5.0 or
higher
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 21
1.2 CP 343-5
1.2.1 Current version
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 6
Firmware version: V4.2
The firmware can be obtained at:
19725255
(http://support.automation.siemens.com
/ww/view/de/19725255)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 343-5
8778841
(http://support.automation.siemens.com
/ww/view/de/8778841)
SIMATIC NET update with CP release:
31803331
(http://support.automation.siemens.com
/ww/view/en/31803331)
SIMATIC NET updates with firmware
release:
19725912
(http://support.automation.siemens.com
/ww/view/de/19725912)
Hardware modification:
• Due to production, no functional
modifications compared with the
previous hardware product version.
The firmware version is unchanged and
therefore compatible and can be used
with hardware product versions 1 and 3
to 6
STEP 7
• STEP 7 Version V5.1 SP2 or higher
You configure the CP as firmware
version V4.0.
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
22 Reference Manual, 07.2013, C79000-G8976-C174-22
1.2.2 Previous versions
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 5
Firmware version: V4.2
The firmware can be obtained at:
19725255
(http://support.automation.siemens.com
/ww/view/de/19725255)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 343-5
8778841
(http://support.automation.siemens.com
/ww/view/de/8778841)
SIMATIC NET update with CP release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
SIMATIC NET updates with firmware
release:
19725912
(http://support.automation.siemens.com
/ww/view/de/19725912)
Hardware modification:
• Bugs fixed, no functional
modifications compared with the
previous hardware product version.
The firmware version is unchanged and
therefore compatible and can be used
with hardware product versions 1, 3, 4
and 5
STEP 7
• STEP 7 Version V5.1 SP2 or higher
You configure the CP as firmware
version V4.0.
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 23
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 4
Firmware version: V4.2
The firmware can be obtained at:
19725255
(http://support.automation.siemens.com
/ww/view/de/19725255)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 343-5
8778841
(http://support.automation.siemens.com
/ww/view/de/8778841)
SIMATIC NET update with CP release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
SIMATIC NET updates with firmware
release:
19725912
(http://support.automation.siemens.com
/ww/view/de/19725912)
Firmware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is compatible and can be used
with hardware product versions 1, 3 and 4
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V4.0
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
24 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 4
Firmware version: V4.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 343-5
8778841
(http://support.automation.siemens.com
/ww/view/de/8778841)
SIMATIC NET update with CP release:
14261822
(http://support.automation.siemens.com
/ww/view/de/14261822)
10605201
(http://support.automation.siemens.com
/ww/view/de/10605201)
Hardware modification:
• Bugs fixed, no functional modifications compared
with the previous version.
The firmware version is unchanged and therefore
compatible and can be used with hardware product
versions 1, 3 and 4
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V4.0
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 3
Firmware version: V4.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
SIMATIC NET update with CP release:
10605201
(http://support.automation.siemens.com
/ww/view/de/10605201)
12324022
(http://support.automation.siemens.com
/ww/view/de/12324022)
Hardware modification:
• Bugs fixed, no functional modifications compared
with the previous hardware product version.
The firmware version is unchanged and therefore
compatible and can be used with hardware product
versions 1 and 3
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V4.0
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 25
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 2
Firmware version: V4.1
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET update with CP release:
10605201
(http://support.automation.siemens.com
/ww/view/de/10605201)
10605523
(http://support.automation.siemens.com
/ww/view/de/10605523)
Extended functionality compared with the previous
firmware version:
- none; bug fixes only -
• compatible and usable with hardware product
versions 1 and 2
Hardware modification:
• due to production, functionally compatible with
predecessor version
STEP 7 Version V5.1
SP2 or higher
can be configured as
firmware version V4.0
Order number:
6GK7 343-5FA01-0XE0
Hardware product version: 1
Firmware version: V4.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET update with CP release:
8117953
(http://support.automation.siemens.com
/ww/view/de/8117953)
The CP 343-5 can be used as a replacement for the
predecessor product CP 343-5 (6GK7 343-5FA00-
0XE0).
Extended functionality compared with previous product
(6GK7-342-5FA00-0XE0):
• The transmission speeds are also supported:
3, 6, 12 Mbps
Additional feature: single module width (predecessor
double width)
STEP 7 Version V5.1
SP2 or higher
SIMATIC S7-300
1.2 CP 343-5
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
26 Reference Manual, 07.2013, C79000-G8976-C174-22
1.2.3 Predecessor modules
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 343-5FA00-0XE0
Hardware product version: 6
Firmware version: V3.0
The firmware can be obtained at:
786302
(http://support.automation.siemens.com
/ww/view/de/786302)
Relevant documentation:
Product information bulletin CP 343-5
Document no.: C79000-Z8964-C7-04
SIMATIC NET update with CP release:
4245246
(http://support.automation.siemens.com
/ww/view/de/4245246)
Basic functionality with:
• PROFIBUS FMS (complying with EN 50170, FMS
client and server function)
• S5-compatible communication via FDL
connections
• S7 communication (server)
• Replacing a module without a programming device
• Routing of PG functions
STEP 7 Version V5.0
SP3 or higher
SIMATIC S7-400 2
2.1 CP 443-5 Basic
2.1.1 Current version
Characteristic data of the device
Order numbers / versions
Required STEP 7 Version (for
Features / new or modified functions full functionality)
Order number:
6GK7 443-5FX02-0XE0
Hardware product version: 3
Firmware version: V4.0
The firmware can be obtained at:
17817495
(http://support.automation.siemens.com
/ww/view/de/17817495)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5 Basic
8776422
(http://support.automation.siemens.com
/ww/view/de/8776422)
Hardware modification:
• due to production, functionally
compatible with predecessor
version
STEP 7
• STEP 7 as of version V5.2 SP1
You configure the CP as firmware
version V4.0.
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 27
SIMATIC S7-400
2.1 CP 443-5 Basic
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
28 Reference Manual, 07.2013, C79000-G8976-C174-22
2.1.2 Previous versions
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 443-5FX02-0XE0
Hardware product version: 2
Firmware version: V4.0
The firmware can be obtained at:
17817495
(http://support.automation.siemens.com
/ww/view/de/17817495)
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5 Basic
8776422
(http://support.automation.siemens.com
/ww/view/de/8776422)
Hardware modification:
• due to production, functionally compatible with
predecessor version
STEP 7 as of version
V5.2 SP1
Order number:
6GK7 443-5FX02-0XE0
Hardware product version: 1
Firmware version: V4.0
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5 Basic
8776422
(http://support.automation.siemens.com
/ww/view/de/8776422)
SIMATIC NET update with CP release:
17143238
(http://support.automation.siemens.com
/ww/view/de/17143238)
New hardware:
• The device is functionally compatible with the
predecessor version.
Modified / improved product characteristics:
• additional PROFIBUS bus fault LED BUSF-LED)
• improved performance (factor of 3)
• reduced current consumption / power dissipation
STEP 7 as of version
V5.2 SP1
SIMATIC S7-400
2.1 CP 443-5 Basic
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 29
2.1.3 Predecessor modules
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 443-5FX01-0XE0
Hardware product version: 3
Firmware version: V3.2
The firmware can be obtained at:
5452112
(http://support.automation.siemens.com
/ww/view/de/5452112)
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5 Basic
8776422
(http://support.automation.siemens.com
/ww/view/de/8776422)
SIMATIC NET update with CP release:
10605528
(http://support.automation.siemens.com
/ww/view/de/10605528)
Hardware modification:
• due to production, functionally compatible with
predecessor version
STEP 7 Version V5.1
SP1 or higher
Order number:
6GK7 443-5FX01-0XE0
Hardware product version: 2
Firmware version: V3.2
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01
SIMATIC NET update with CP release:
5472312
(http://support.automation.siemens.com
/ww/view/de/5472312)
The CP 443-5 Basic listed here can be used as a
replacement for the predecessor product CP 443-5
Basic (6GK7 443-5FX00-0XE0).
Extended functionality compared with the previous
firmware version:
- none; bug fixes only
(Extended functionality compared with previous
product: see under version 1)
STEP 7 Version V5.1
SP1 or higher
SIMATIC S7-400
2.1 CP 443-5 Basic
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
30 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 443-5FX01-0XE0
Hardware product version: 2
Firmware version: V3.1
Relevant documentation:
CP 443-5 Basic product information
Document no.: C79000-Z8964-C055-
02
SIMATIC NET update with CP release:
4246730
(http://support.automation.siemens.com
/ww/view/de/4246730)
Extended functionality compared with the previous
firmware version:
- none; bug fixes only -
STEP 7 Version V5.0
SP3 or higher
Order number:
6GK7 443-5FX01-0XE0
Hardware product version: 1
Firmware version: V3.1
Relevant documentation:
CP 443-5 Basic product information
Document no.: C79000-Z8964-C055-
02
SIMATIC NET update with CP release:
4246662
(http://support.automation.siemens.com
/ww/view/de/4246662)
Extended functionality compared with the previous
firmware version:
- none; bug fixes only -
STEP 7 Version V5.0
SP3 or higher
SIMATIC S7-400
2.1 CP 443-5 Basic
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 31
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7
Version (for
full functionality)
Order number:
6GK7 443-5FX01-0XE0
Hardware product version: 1
Firmware version: V3.0
Relevant documentation:
CP 443-5 Basic product information
Document no.: C79000-Z8964-C055-
01
SIMATIC NET update with CP release:
4245091
(http://support.automation.siemens.com
/ww/view/de/4245091)
Extended functionality compared with previous
product CP 443-5 Basic (6GK7 443-5FX00-0XE0):
• Routing of PG functions
• Replacing a module without a programming device
• Use in SIMATIC S7-400H (fault-tolerant
automation system)
• Time-of-day synchronization
STEP 7 Version V5.0
SP3 or higher
Order number:
6GK7 443-5FX00-0XE0
Hardware product version: 9
Firmware version: V2.42
The firmware can be obtained at:
754121
(http://support.automation.siemens.com
/ww/view/de/754121)
Relevant documentation:
CP 443-5 Basic product information
Document no.: C79000-Z8964-C008-
05
SIMATIC NET update with CP release:
4245081
(http://support.automation.siemens.com
/ww/view/de/4245081)
Basic functionality with:
• PROFIBUS FMS (complying with EN 50170, FMS
client and server function)
• S5-compatible communication via FDL
connections
• S7 communication (server)
STEP 7 Version V5.0
SP3 or higher
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
32 Reference Manual, 07.2013, C79000-G8976-C174-22
2.2 CP 443-5 Extended
2.2.1 Current version
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX05-0XE0
Hardware product version: 1
Firmware version: V7.1.1
68189209
(http://support.automation.siemens.com
/ww/view/en/68189209)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 07 - 7/2011
8777196
(http://support.automation.siemens.com
/ww/view/en/8777196)
SIMATIC NET updates with firmware
release:
68188938
(http://support.automation.siemens.com
/ww/view/en/68188938)
Firmware modification.
Enhanced function:
• Support of SIMATIC S7-400H V6
Product improvements and bugs fixed,
including:
• Correction to data record routing
(e.g. with SIMATIC PDM access).
• PROFIBUS DP: Problem when
using DP master class 2 services.
• Time synchronization: Correction in
time of day status.
Depending on the STEP 7 version you
are using, you have the following
options:
STEP 7
• STEP 7 as of version V5.5 SP1
Note:
Firmware download (with firmware
download profile
"FWL_FAST_LOAD") is only
available as of this STEP 7 version.
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1.
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
STEP 7 Professional
• V12
The full range of functions can be
configured with firmware version
V7.0
• V11
The functional range of the
following CP type can be
configured:
– 6GK7 443-5DX04-0XE0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 33
2.2.2 Previous versions
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX05-0XE0
Hardware product version: 1
Firmware version: V7.0
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 07 - 7/2011
8777196
(http://support.automation.siemens.com
/ww/view/en/8777196)
SIMATIC NET update with CP release:
54679920
(http://support.automation.siemens.com
/ww/view/en/54679920)
Hardware and firmware modification
The device is functionally compatible
with the predecessor version.
Depending on the STEP 7 version you
are using, you have the following
options:
STEP 7
• STEP 7 as of version V5.5 SP1
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1.
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
STEP 7 Professional
The functional range of the following
CP type can be configured:
• 6GK7 443-5DX04-0XE0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
34 Reference Manual, 07.2013, C79000-G8976-C174-22
2.2.3 Predecessor modules
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.8.1
The firmware can be obtained at:
64933815
(http://support.automation.siemens.com
/ww/view/de/64933815)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
64933813
(http://support.automation.siemens.com
/ww/view/en/48072265)
Firmware modification:
Product improvement and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements and bugs fixed,
including:
• PROFIBUS DP: Problem when
using DP master class 2 services.
• Time synchronization: Correction in
time of day status.
For more information, refer to SIMATIC
NET updates
Depending on the STEP 7 version you
are using, you have the following
options:
STEP 7
• STEP 7 V5.5 SP1
You configure the CP as
6GK7 443-5DX04-0XE0
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
• STEP 7 as of version V5.2 SP1
You configure the CP as firmware
version V6.0
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
STEP 7 Professional
• STEP 7 V11.0
You configure the CP as
6GK7 443-5DX04-0XE0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 35
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE1
Hardware product version: 1
Firmware version: V6.8.1
The firmware can be obtained at:
64933815
(http://support.automation.siemens.com
/ww/view/de/64933815)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
64933813
(http://support.automation.siemens.com
/ww/view/en/48072265)
Firmware modification:
Product improvement and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements and bugs fixed,
including:
• PROFIBUS DP: Problem when
using DP master class 2 services.
• Time synchronization: Correction in
time of day status.
For more information, refer to SIMATIC
NET updates
Depending on the STEP 7 version you
are using, you have the following
options:
STEP 7
• STEP 7 V5.5 SP1
You configure the CP as
6GK7 443-5DX04-0XE0
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
• STEP 7 as of version V5.2 SP1
You configure the CP as firmware
version V6.0
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
STEP 7 Professional
• STEP 7 V11.0
You configure the CP as
6GK7 443-5DX04-0XE0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
36 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE1
Hardware product version: 1
Firmware version: V6.7
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
48072265
(http://support.automation.siemens.com
/ww/view/en/48072265)
Hardware modification:
• due to production, functionally
compatible with predecessor
version
The module does not conform to
RoHS.
Depending on the STEP 7 version you
are using, you have the following
options:
STEP 7
You configure the CP as
6GK7 443-5DX04-0XE0
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
STEP 7 Professional
You configure the CP as
6GK7 443-5DX04-0XE0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 37
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.6
The firmware can be obtained at:
48067029
(http://support.automation.siemens.com
/ww/view/en/48067029)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
48072265
(http://support.automation.siemens.com
/ww/view/en/48072265)
Firmware modification:
Product improvement and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements:
• Improvement of the display of the
EXTF LED
• Improved response to bus short-
circuits
Depending on the STEP 7 version you
are using, you have the following
options:
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
38 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.5.11
The firmware can be obtained at:
42310454
(http://support.automation.siemens.com
/ww/view/de/42310454)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 03/2009
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
42310453
(http://support.automation.siemens.com
/ww/view/de/42310453)
Firmware modification:
Product improvement and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements:
• Improvements in the behavior of the
bus in H systems when using fast
DP slaves.
• A removed DP slave module is
indicated by the EXTF-LED of the
CPU even after turning station
power off and on again.
Depending on the STEP 7 version you
are using, you have the following
options:
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 39
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.5
The firmware can be obtained at:
34830644
(http://support.automation.siemens.com
/ww/view/de/34830644)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 2/2003
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
34828895
(http://support.automation.siemens.com
/ww/view/de/34828895)
Firmware modification:
Product improvement and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements:
• Adaptation of the time
synchronization to conform with the
standard (IEC 61158-6) by
integrating time of day 2 in the time-
of-day frame;
• Improvements in the parameter
assignment of very slow DP slaves.
The firmware version is compatible and
can be used with hardware product
versions 1 and 2
Depending on the STEP 7 version you
are using, you have the following
options:
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V6.3 or higher.
• STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
40 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.4
The firmware can be obtained at:
26372646
(http://support.automation.siemens.com
/ww/view/de/26372646)
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 2/2003
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
26424892
(http://support.automation.siemens.com
/ww/view/de/26424892)
Firmware modification:
• Bugs fixed, no functional
modifications compared with the
previous version.
The firmware version is compatible and
can be used with hardware product
versions 1, 2 and 3
STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 41
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.3
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 2/2003
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
25374772
(http://support.automation.siemens.com
/ww/view/de/25374772)
Firmware modification:
• Bugs fixed, no functional
modifications compared with the
previous version (for details, refer to
SIMATIC NET updates).
STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 2
Firmware version: V6.1
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 2/2003
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
Hardware modification:
• due to production, functionally
compatible with predecessor
version
STEP 7 as of version V5.4
You configure the CP as firmware
version V6.1
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
42 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 1
Firmware version: V6.1
Relevant documentation:
S7 CPs for PROFIBUS manual
• General section
as of Release 04 - 2/2003
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
as of release 06 - 6/2005
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
21556240
(http://support.automation.siemens.com
/ww/view/de/21556240)
Hardware and firmware modification
The device is functionally compatible
with the predecessor version.
Modified / improved product
characteristics:
• Getting the bus topology in a DP
master system
The CP 443-5 Extended operating
as DP master supports the
measurement of the PROFIBUS
bus topology in a DP master system
using a diagnostics repeater (DP
slave).
STEP 7 as of version V5.4
Order number:
6GK7 443-5DX04-0XE0
Hardware product version: 1
Firmware version: V6.0
Relevant documentation:
S7 CPs for PROFIBUS manual
as of Release 04 - 2/2003
• General section
1158693
(http://support.automation.siemens.com
/ww/view/en/1158693)
• Part specific to the CP 443-5
Extended
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET update with CP release:
19337545
(http://support.automation.siemens.com
/ww/view/de/19337545)
Hardware and firmware modification
The device is functionally compatible
with the predecessor version.
Modified / improved product
characteristics:
• additional PROFIBUS bus fault LED
BUSF-LED)
• improved performance (factor of 3)
• reduced current consumption /
power dissipation
STEP 7 Version V5.2.1 or higher
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 43
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 3
Firmware version: V5.3
The firmware can be obtained at:
34830645
(http://support.automation.siemens.com
/ww/view/en/34830645)
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 04 - 2/2003
• General section
8774037
(http://support.automation.siemens.com
/ww/view/de/8774037)
• Part specific to the CP 443-5
Extended
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
34829451
(http://support.automation.siemens.com
/ww/view/en/34829451)
Firmware modification:
Product improvements and bugs fixed,
no functional modifications compared
with the previous version.
Product improvements:
• Adaptation of the time
synchronization to conform with the
standard (IEC 61158-6) by
integrating time of day 2 in the time-
of-day frame;
• Improvements in the parameter
assignment of very slow DP slaves;
• Plant changes using CiR
(Configuration in RUN) can now
also be made when large numbers
of I/Os are involved.
The firmware version is compatible and
can be used with hardware product
versions 1, 2 and 3
Depending on the STEP 7 version you
are using, you have the following
options:
• STEP 7 as of version V5.4 SP4
You configure the CP as firmware
version V5.2 or higher.
or
• STEP 7 as of version V5.2
You configure the CP as firmware
version V5.0 or V5.1.
or
• STEP 7 Version V5.1 SP2 or higher
You configure the CP as firmware
version V4.0
If you use the module as a replacement
or when the functionality of the
predecessor module is adequate,
configuration and diagnostics are
possible using earlier STEP 7 versions.
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
44 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 3
Firmware version: V5.2
The firmware can be obtained at:
27201492
(http://support.automation.siemens.com
/ww/view/de/27201492)
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 04 - 2/2003
• General section
8774037
(http://support.automation.siemens.com
/ww/view/de/8774037)
• Part specific to the CP 443-5
Extended
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET updates with firmware
release:
34829451
(http://support.automation.siemens.com
/ww/view/en/34829451)
Firmware modification:
Bugs fixed, no functional modifications
compared with the previous version.
The firmware version is compatible and
can be used with hardware product
versions 1, 2 and 3
STEP 7 as of version V5.2
can be configured as firmware version
V5.1
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 45
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 3
Firmware version: V5.1
The firmware can be obtained at:
15121256
(http://support.automation.siemens.com
/ww/view/de/15121256)
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 04 - 2/2003
• General section
8774037
(http://support.automation.siemens.com
/ww/view/de/8774037)
• Part specific to the CP 443-5
Extended
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET update with CP release:
15117378
(http://support.automation.siemens.com
/ww/view/de/15117378)
14256451
(http://support.automation.siemens.com
/ww/view/de/14256451)
Firmware modification:
Bugs fixed, no functional modifications
compared with the previous version.
The firmware version is compatible and
can be used with hardware product
versions 1, 2 and 3
STEP 7 as of version V5.2
can be configured as firmware version
V5.0
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
46 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 3
Firmware version: V5.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 04 - 2/2003
• General section
8774037
(http://support.automation.siemens.com
/ww/view/de/8774037)
• Part specific to the CP 443-5
Extended
8777196
(http://support.automation.siemens.com
/ww/view/de/8777196)
SIMATIC NET update with CP release:
14256451
(http://support.automation.siemens.com
/ww/view/de/14256451)
Hardware modification:
• due to production, functionally
compatible with predecessor
version
STEP 7 as of version V5.2
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 2
Firmware version: V5.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 03 - 11/2002
SIMATIC NET update with CP release:
13729134
(http://support.automation.siemens.com
/ww/view/de/13729134)
Extended functionality compared with
the previous firmware version:
• CiR functionality (with CiR, it is
possible to add to or modify the
distributed I/O during ongoing
operation.) - in the standard system
• Enabling /disabling DP slave - in the
standard system
STEP 7 as of version V5.2
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 2
Firmware version: V4.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET update with CP release:
10604437
(http://support.automation.siemens.com
/ww/view/de/10604437)
Hardware modification:
• due to production, functionally
compatible with predecessor
version
STEP 7 Version V5.1 SP2 or higher
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 47
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX03-0XE0
Hardware product version: 1
Firmware version: V4.0
Relevant documentation:
S7 CPs for PROFIBUS manual
Release 01 - 6/2001
SIMATIC NET update with CP release:
8262972
(http://support.automation.siemens.com
/ww/view/de/8262972)
The CP 443-5 Extended listed here can
be used as a replacement for the
predecessor products CP 443-5
Extended (6GK7 443-5DX00-0XE0,
6GK7 443-5DX01-0XE0 and 6GK7
443-5DX02-0XE0)
Extended functionality compared with
previous product:
• DPV1 functionality.
• When using STEP7 V5.1 SP2 and
the CPUs as of V3.0, there is a
performance improvement in the
transfer of consistent data (SFC14,
SFC15).
• Consistent data can be stored in the
full process image or in a partition
(up to 32 bytes). To do this you no
longer need to call SFC14 and
SFC15. Updating is handled by the
system.
STEP 7 Version V5.1 SP2 or higher
Order number:
6GK7 443-5DX02-0XE0
Hardware product version: 2
Firmware version: V3.3
The firmware can be obtained at:
12011123
(http://support.automation.siemens.com
/ww/view/de/12011123)
Relevant documentation:
CP 443-5 Extended product information
• Document no.: A5E 000 74498
SIMATIC NET update with CP release:
12011694
(http://support.automation.siemens.com
/ww/view/de/12011694)
Extended functionality compared with
the previous firmware version:
- none; bug fixes only
STEP 7 Version V5.1 or higher
can be configured as firmware version
V3.2
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
48 Reference Manual, 07.2013, C79000-G8976-C174-22
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX02-0XE0
Hardware product version: 2
Firmware version: V3.2
Relevant documentation:
CP 443-5 Extended product information
• Document no.: A5E 000 74498
SIMATIC NET update with CP release:
4894460
(http://support.automation.siemens.com
/ww/view/de/4894460)
The CP 4435 Extended can be used as
a replacement for the following
previous products:
CP 443-5 Extended
Order no.: 6GK7 443-5DX01-0XE0
Order no.: 6GK7 443-5DX00-0XE0
Extended functionality compared with
previous product CP 443-5 Extended
(6GK7 443-5DX01-0XE0 V1.2.1):
• expanded DP functionality (DP
direct data exchange, constant bus
cycle time)
• Time-of-day synchronization
• Routing of PG functions
• Larger configuration memory
• Use in SIMATIC S7-400H (fault-
tolerant)
• Data record routing
• Modifications to the plant during
operation are possible (H system);
• Optimized DP line failover (H
system);
STEP 7 Version V5.1 or higher
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
Reference Manual, 07.2013, C79000-G8976-C174-22 49
Characteristic data of the device
Order numbers / versions Features / new or modified functions
Required STEP 7 Version (for
full functionality)
Order number:
6GK7 443-5DX01-0XE0
Product version: 2
Firmware version: V1.21
The firmware can be obtained at:
752061
(http://support.automation.siemens.com
/ww/view/de/752061)
Relevant documentation:
CP 443-5 Extended product information
• Document no.: C79000-Z8964-C33-
02
SIMATIC NET update with CP release:
4245061
(http://support.automation.siemens.com
/ww/view/de/4245061)
The CP 4435 Extended can be used as
a replacement for the following
previous products:
CP 443-5 Extended
Order no.: 6GK7 443-5DX00-0XE0
Extended functionality compared with
previous product CP 443-5 Extended
(6GK7 443-5DX00-0XE0):
• Sync/freeze and free layer 2 access
STEP 7 Version V5.0 or higher
Order number:
6GK7 443-5DX00-0XE0
Product version: 4
Firmware version: V1.10
The firmware can be obtained at:
184015
(http://support.automation.siemens.com
/ww/view/de/184015)
Relevant documentation:
CP 443-5 Extended product information
• Document no.: C79000-Z8964-C9-
03
SIMATIC NET update with CP release:
4242783
(http://support.automation.siemens.com
/ww/view/de/4242783)
Basic functionality with:
• PROFIBUS-DP as DP master
• S5-compatible communication via
FDL connections
• S7 communication
STEP 7 Version V5.0 or higher
SIMATIC S7-400
2.2 CP 443-5 Extended
Version History / Current Downloads for the SIMATIC NET S7-CPs PROFIBUS
50 Reference Manual, 07.2013, C79000-G8976-C174-22
