P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 1Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Long Life Cermet Potentiometer 2 Million Cycles
DESIGN SUPPORT TOOLS
FEATURES
• 2 million cycles
• Cermet element
• 12.5 mm square single turn panel control
• 4, 6 and 6.35 shaft diameters and 29 terminal styles
• Multiple assemblies - up to four modules
• Test according to CECC 41000 or IEC 60393-1
• Low temperature coefficient
• Custom designs on request
• Linearity ± 3 % (± 2 % available)
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
click logo to get started
Available
Models
QUICK REFERENCE DATA
Multiple module Up to 4 modules
Switch module Yes
Detent module Yes
Special electrical laws A: linear, L: logarithmic, F: reverse logarithmic and others see specifications
Sealing level IP 64
Lifespan 2M cycles
VERSATILE MODULAR COMPACT ROBUST
CONFIGURATION EXAMPLE - Dimensions in millimeters (inches) ± 0.5 mm (± 0.02")
Single module, single shaft, vertical mounting, PC pins with support plate, metric bushing and shaft
Dual modules, single shaft, PC pins with front support plates, imperial bushing and shaft
M10 x 0.75
6
Ø (0.236) 9.5
(0.374)
16
(0.626)
12.7
(0.500)
8
(0.315)
2.54
(0.100)
2.54
(0.100)
3/8" x 3/8"
12.5
(0.492)
13.1
(0.516)
2.54
(0.100)
2.54
(0.100)
8
(0.325)
9.5
(0.374)
3.6
(0.143)
6.35
Ø (0.250)
19.05
(0.750) 7.62
(0.300)
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 2Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
GENERAL SPECIFICATIONS
Note
• Nothing stated herein shall be construed as a guarantee of quality or durability
ELECTRICAL (initial)
Resistive element Cermet
Electrical travel 270° ± 10°
Standard resistance values 1 k, 5 k, 10 k, 50 k
Tolerance
standard ± 20 %
on request ± 5 % or ± 10 %
Taper
Circuit diagram
Power rating at 70 °C
linear taper 0.1 W at +70 °C
non-linear taper 0.05 W at +70 °C
multiple assemblies 0.1 W at +70 °C per module
Temperature coefficient (typical) ± 150 ppm
Limiting element voltage 350 V
End resistance (typical) 2
Independent linearity ± 3 % (± 2 % available)
Insulation resistance 106 M min.
Dielectric strength 1500 VRMS min.
Attenuation -
Mechanical endurance 2 000 000 cycles
100
80
60
40
20
00 10080604020
% CLOCKWISE SHAFT ROTATION
% TOTAL RESISTANCE
F
L
A
a
(1)
b
(2)
c
(3)
cw
AMBIENT TEMPERATURE IN °C
POWER IN W
0 20 40 60 70 80 100 120 140
0
0.10
P11L
LINEAR TAPER
0.05
P11L
LOG. TAPER
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 3Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
MECHANICAL (initial)
Mechanical travel 300° ± 5°
Operating torque (typical)
Single and dual assemblies 0.4 Ncm to 1.7 Ncm max. (0.57 oz.-inch to 2.55 oz.-inch max.)
Three to four modules (per module) 0.2 Ncm to 0.3 Ncm max. (0.28 oz.-inch to 0.42 oz.-inch max.)
End stop torque
4 mm dia. shafts 35 Ncm max. (2.9 lb-inch max.)
6 mm and 1/4" dia. shafts 80 Ncm max. (6.8 lb-inch max.)
Tightening torque
7 mm dia. bushings 150 Ncm max. (13 lb-inch max.)
10 mm and 3/8" dia. bushings 250 Ncm max. (21 lb-inch max.)
Weight 7 g to 9 g per module (0.25 oz. to 0.32 oz.)
ENVIRONMENTAL
Operating temperature range -55 °C to +125 °C
Climatic category 55/125/56
Sealing IP64
MARKING
•Potentiometer module
Vishay logo, SAP code of ohmic value, and tolerance in %,
identify P11L version, variation law, manufacturing date (four
digits), “3” for the lead 3
• Switch module
Version, manufacturing date (four digits), “c” for common
lead
PACKAGING
• Box
PERFORMANCES
TESTS CONDITIONS TYPICAL VALUES AND DRIFTS
RT/RT (%) R1-2/R1-2 (%) OTHER
Electrical endurance 1000 h at rated power
90’/30’ - ambient temp. 70 °C ± 2 % - -
Climatic sequence Dry heat at +125 °C/damp heat
cold -55 °C/damp heat, 5 cycles ± 1 % - -
Damp heat, steady state +40 °C, 93 % relative humidity
56 days ± 2 % - Insulation resistance: > 1000 M
Change of temperature -55 °C to +125 °C, 5 cycles ± 0.2 % - -
Mechanical endurance
2 million cycles
turn angle: ± 60°
temperature: 20 °C
± 20 % - Independent linearity: ± 10 %
Shock 50 g’s, 11 ms
3 shocks - 3 directions ± 0.2 % ± 0.5 % -
Vibration 10 Hz to 55 Hz
0.75 mm or 10 g’s, 6 h ± 0.2 % - V1-2/V1-3 = ± 0.5 %
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 4Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
P11L 1
2
3
4
STANDARD RESISTANCE ELEMENT DATA
STANDARD
RESISTANCE
VALUES
LINEAR TAPER NON-LINEAR TAPER
MAX. POWER
AT 70 °C
MAX. WORKING
VOLTAGE
MAX. POWER
AT 70 °C
MAX. WORKING
VOLTAGE
WVWV
1K 0.1 10.0 0.05 7.1
5K 0.1 22.4 0.05 15.8
10K 0.1 31.6 0.05 22.4
50K 0.1 70.7 0.05 50.0
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 5Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Note
• Hardware supplied in separate bags
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
ØL
F 3/8" 3/8"
Q78
V109.5
BUSHING DIMENSIONS
AB
CK
J
PANEL CUT OUT
Ø H
G
Bushings
F and V
BUSHINGS
mm (± 0.5) mm (± 0.5) INCHES (± 0.02)
VQF
A Shafts Ø 6 4 1/4
B Bushing Ø 10 7 3/8
C L 9.5 8 3/8
J Lead versions X.. Y.. 7 5 0.278
K 11.1 9.1 0.436
G Panel 8.2 6.2 0.323
H Cutout Ø 10.5 7.5 0.394
Thread 0.75 0.75 32 thread/inch
Wrench nut 12 10 0.500
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 6Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
A =
see table
below
B =
C =
0 = without
peg
LOCATING PEGS (anti-rotation lug)
The locating peg is provided by a plate mounted on the bushing
and positioned by the module sides. Four set positions are
available, clock face orientation: 12, 3, 6, 9. CODE Ø d (mm) L (mm) e (mm)
All P11 bushings have a double flat. When panel mounting
holes have been punched accordingly, an anti-rotation lug is
not necessary.
A2 6.2 0.7
B 2 7.75 0.7
Locating peg code C not available for bushing Q. C 3.5 13.5 1.1
Locating pegs are supplied in separate bags with nuts and
washers
12
L
3
6
9
Ø d
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 7Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT
STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
Ø L S = slotted
AP = Custom shaft R = round
EA 4 9.5 F = flatted
EB 4 12.5 D = custom
EJ 4 22
FG 6 16
FL 6 25
FR 6 50
GG 1/4" 5/8"
GH 1/4" 3/4"
GJ 1/4" 7/8"
GL 1/4" 1"
GO 1/4" 1.5"
SHAFTS - Dimensions in millimeters (inches)
The shaft length is always measured from the mounting face.
Standard shafts are designed by a 3 letters code (3 digits). Shaft
slots and flats are aligned with the wiper position (± 10°); picture
shows shaft with wiper at middle of mechanical/electrical
course.
All standard shafts are slotted except flatted and splined, see
exeptions for bushing.
SPLINED SHAFT
FLATTED SHAFT
CUSTOM SHAFTS
When special shafts are required - flat, threated ends, special
shaft lengths, etc. a drawing is required.
STANDARD COMBINATION OF SHAFT STYLES AND BUSHINGS
SHAFT DIA. BUSHING CODE SHAFT LENGTH AND STYLE AVAILABLE IN STANDARD
(others on request)
6 V FGS FLS FRS
6.35 F GGS GHS GJS GLS GOS GHF
4QEASEBSEJSFHK
Ø 7
Ø 6
19
Bushing: Q
Shaft: FHK
19.1
8 ± 0.5
Ø 6.35
5.5 ± 0.05
Bushing: F
Shaft: GHF
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 8Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT
STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
Available leads
A00 W00 X00 Y00 Z00
A10 W10 X03 Y03 Z03
A13 W20 X04 Y04 Z04
A14 X10 Z10
A20 X13 Z13
A23 X14 Z14
A24 X20 Z20
X23 Z23
X24 Z24
FIRST DIGIT SECOND DIGIT THIRD DIGIT
YSoldering lugs
0
Y = 4.65 (0.183")
A, X, Z, W = 5.08 (0.200") pin spacing
pins section 0.9 x 0.3 (0.035" x 0.012")
05.08 (0.200") space between modules
XPCB pins 37.62 (0.300") space between modules
ZPCB pins with front support plate 410.16 (0.400") space between modules
APCB pins with front and back support
plates 12.54 (0.100") pin spacing
pin section 0.6 x 0.3 (0.024" x 0.012")
WPCB pins - vertical mounting with 2 extra
pins - 1 module only 25.08 (0.200") pin spacing
pins section 0.6 x 0.3 (0.024" x 0.012")
DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")
THE POSITION OF EACH MODULE IS FREE
BUSHINGS MILLIMETERS (± 0.5) INCHES (± 0.02)
VQF
E Leads Z00 3.85 1.85 0.150
E Leads Z1. Z2. A.. 3.6 1.6 0.140
F Leads Z0: 5.08 (0.200") Leads A...Z1, Z2: 3.81 (0.150")
J Leads X.. Y.. 7 5 0.278
3.71
(0.146)
6.85
(0.270)
J
13
(0.512)
4.7
(0.185)
12.5
(0.492)
12.5
(0.492)
4.7
(0.185)
2.4
(0.09)
1.8
(0.07)
5
(0.197)
0.9
(0.035)
0.9
(0.035)
SOLDER LUGS Y
1
2.54
(0.100)
5.08
(0.200)
X12X-X
23 123
PCB PIN OUT
HORIZONTAL MOUNTING
EF
6.35
(0.250)
3
2
1
A/A2
(0.150)
3.81
(0.150)
A1
3.81
FRONT AND REAR SUPPORT PLATES FRONT SUPPORT PLATE
2.54
(0.100)
5.08
(0.200)
3.81
(0.150)
5.08
(0.200)
5.08
(0.200)
3.81
(0.150)
2Z1ZZ
123 123 123
VERTICAL MOUNTING
AB
CK4
(0.157)
12.7
(0.500)
12.7
(0.500)
5.08
(0.200)
2.54
(0.100)
12.7
(0.500)
W-W2
1 2 3
W1
12 3
Rear support
plate
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 9Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
ORDERING INFORMATION (part number)
P11L2FAGOSY00502KA
MODEL NUMBER OF
MODULES BUSHING LOCATING
PEG SHAFT SHAFT
STYLE LEADS
RESISTANCE CODE/
TOLERANCE/
TAPER OR SPECIAL
Resistance code:
1K = 102
5K = 502
10K = 103
50K = 503
Tolerance code:
standard:
M = ± 20 %
on request:
K = ± 10 %, J = ± 5 %
Taper: A, L, F
or
special code
given by Vishay
SPECIAL CODES GIVEN BY VISHAY
Option available:
•Custom shaft
• Specific design on request
• Specific linearity
• Multiple assemblies with various modules
APPLICATION NOTE
The potentiometer shall be used in voltage divider with an impedance load
at least 100 times higher than the total potentiometer nominal resistance
value.
Advised load impedance:
1 M min. for resistance range of 1 k to 50 k
(1) a
(2) b
c (3)
cw
Vs
Ve
Z >
1 MΩ
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 10 Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
P11L OPTION: ROTARY SWITCH MODULES
• Rotary switch
• Current up to 2 A
• Actuation CW or CCW position
• Sealing IP60
MODULES: RS ON/OFF SWITCH
RSI CHANGEOVER SWITCH
The position of each module is free.
RS and RSI rotary switches are housed in a standard P11L
module size 12.7 mm x 12.7 mm x 5.08 mm (0.5" x 0.5" x 0.2").
They have the same terminal styles as the assembled electrical
modules.
An assembly can comprise 1 or more switch modules.
Switch actuation is described as seen from the shaft end.
D: Means actuation in maximum CCW position
F: Means actuation in maximum CW position
The switch actuation travel is 25° with a total mechanical
travel of 300° ± 5° and electrical travel of electrical modules is
238° ± 10°.
Leads finish: Gold plated
RDS SINGLE POLE SWITCH, NORMALLY OPEN
In full CCW position, the contact between 1 and 3 is open. It is
made at the beginning of the travel in CW direction.
RSF SINGLE POLE SWITCH, NORMALLY OPEN
In full CW position, the contact between 1 and 3 is open. It is
made at the beginning of the travel in CCW direction.
RSID SINGLE POLE CHANGEOVER
In full CCW position, the contact is made between 3 and 2 and
open between 3 and 1. Switch actuation (CW direction)
reverses these positions.
RSIF SINGLE POLE CHANGEOVER
In full CW position, the contact is made between 1 and 2 and
open between 1 and 3. Switch actuation (CCW direction)
reverses these positions.
SWITCH SPECIFICATIONS
Switching power maximum 0.5 VA =
Switching current maximum 0.1 A, 5 V =
Maximum current through element 2 A
Contact resistance 100 m
Dielectric
strength
Terminal to terminal 1000 VRMS
Terminal to bushing 2000 VRMS
Maximum voltage operation 5 V =
Insulation resistance between contacts 106 M
Life at Pmax. 100 000 actuations
Minimal travel 25°
Operating temperature -40 °C to +85 °C
ELECTRICAL DIAGRAM
Note
(1) Common
ORDERING INFORMATION (First order only)
RSD SPST: Single pole, open switch in CCW position - 2 pins
RSF SPST: Single pole, open switch in CW position - 2 pins
RSID SPDT: Single pole, changeover switch in CCW position - 3 pins
RSIF SPDT: Single pole, changeover switch in CW position - 3 pins
RSIF
CW POSITION
1 (1) 32
RSID
CCW POSITION
13 (1)
2
RSD
RSF
13
RSID
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 11 Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
P11L OPTION: DETENT MODULES
The detents mechanism is housed in a standard P11L module.
Up to 21 detent positions available.
Count detents as follows: 1 for CCW position, 1 for full CW
position, plus the other positions forming equal resistance
increments (linear taper) - not equal angles.
Available: CVID - CVIF - CVIM
CV3 - CV11 - CV21
Mechanical endurance: 50 000 cycles
ORDERING INFORMATION (First order only for special code creation)
CV1M 1 detent at half travel
CV1D 1 detent at CCW position
CV1F 1 detent at CW position
CV3 3 detents
CV11 11 detents
CV21 21 detents
P11L OPTION: NEUTRAL MODULES “EN”
Neutral or screen module is housed in a standard P11L module.
It is used as a screen between two electrical modules.
The leads can be connected to ground.
ORDERING INFORMATION (First order only for special code creation)
EN Neutral module
P11L OPTION: SPECIAL LINEARITY - CONFORMITY
The independent linearity (conformity for the non-linear laws) is
the maximum gap V between the actual variation curve and
the theoretical variation curve the nearest to it. The linearity and
the conformity are expressed in percentage of the total applied
voltage E
They are measured over 90 % of actual electrical travel
(centered).
On request linearity can be guaranteed in linear taper.
ORDERING INFORMATION (First order only)
J123 Independent linearity ± 3 % (linear law)
J145 Independent linearity ± 2 % (linear law) For other request, contact us.
CVID CVIM CVIF CV1 1
ββα =
270 °
n - 1
β = α+ 15 °
α
CV1M
EN
V
E
V
Limits of
linearity test
Effective electrical travel
Degrees
linearity conformity ± Vmax.
E
-----------------------
=
J123
P11L
www.vishay.com Vishay Sfernice
Revision: 07-Mar-17 12 Document Number: 51060
For technical questions, contact: sferpottrimmers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
EXAMPLES OF FIRST ORDER INFORMATION
FIRST EXAMPLE: Triple module (switch is counted as a module)
P11L3VAFGSY00
MODEL
P11L 3 MODULES BUSHING
VLOCATING PEG
STANDARD SHAFT
16 mm FMS
SLOTTED
SOLDER LUGS SPECIAL TO BE
DEFINED BY VISHAY
ORDERING INFORMATION:
PART NUMBER P11L3VAFGSY00.....
SHAFT AND BUSHING See drawing of special shaft attached
MODULE NO. 1 503 M A
MODULE NO. 2 103 M A J123
MODULE NO. 3 503 M A
PART NUMBER DESCRIPTION (used on some Vishay document or label, for information only)
P11L 3 V A FG S Y00 T1927 e3
MODEL MODULES BUSHING LOCATING
PEG SHAFT SHAFT
STYLE LEADS VALUE TOL. TAPER SPECIAL SPECIAL LEAD
(Pb)-FREE
RELATED DOCUMENTS
APPLICATION NOTES
Potentiometers and Trimmers www.vishay.com/doc?51001
Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029
Legal Disclaimer Notice
www.vishay.com Vishay
Revision: 08-Feb-17 1Document Number: 91000
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED