Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes Meets AEC-Q200 Requirements Suppression of common mode noise without attenuating the signal Magnetically shielded versions for lower Rdc and higher current Supports CAN-Bus, A2B and other IVN high speed differential signal lines (LVDS) Electrical Specifications @ 25C Common Mode Impedance (10MHZ) Part Number Min Inductance (uH) Typ Standard Tolerance RDC ( Max) Leakage Inductance (nH) Max IDC (A) Max Isolation Resistance (M) Min Rated Voltage (V) Max Operating Temperature Range -55oC to +155C PE-1210ACCXXXSTS PE-1210ACC110STS 300 550 11 +50/-30% 0.4 50 0.3 10 80 PE-1210ACC220STS 500 1100 22 +50/-30% 0.5 70 0.25 10 80 PE-1210ACC510STS 1000 2600 51 +50/-30% 0.7 130 0.2 10 80 PE-1210ACC101STS 2200 5100 100 +50/-30% 1.5 180 0.15 10 80 Operating Temperature Range PE-1812ACCXXXSTS -40oC to +125C PE-1812ACC110STS 300 600 11 +50/-30% 0.5 45 0.36 10 50 PE-1812ACC220STS 600 1200 22 +50/-30% 0.6 50 0.31 10 50 PE-1812ACC510STS 1500 3500 51 +50/-30% 1 150 0.23 10 50 PE-1812ACC101STS 3000 7500 100 +50/-30% 2 200 0.2 10 50 Schematic Mechanical A B 1 4 2 3 C View from PCB PIN 1 D W All Units in mm X S Bifilar winding (representation only) T SODLER PAD(mm) Component Dimensions (mm) Series A B C D e f 1210 ACC 3.2+/-0.20 2.5 +/-0.20 2.5 MAX 3.2 +/-0.20 3.2 +/-0.20 3.2 +/-0.20 4.40 2.40 3.00 1.20 1812 ACC 4.5 +/-0.20 3.2 +/-0.20 3.0 MAX 3.2 +/-0.20 0.65+/-0.15 0.70+/-0.15 5.90 3.20 3.40 1.60 1 Networking.PulseElectronics.com X T S W W717.G (03/19) Temp vs DC Current Impedance vs Frequency PE-1210ACC110STS Differential mode T@25oC 1000 50.0 100 11uH 40.0 11uH 30.0 10 1.6 T ( o C) 60.0 Impedance () 10000 3.4 Common mode 20.0 1 0.1 3.2 10.0 0 10 100 1000 0.0 0.0 10000 5.9 0.1 0.2 0.3 0.4 0.5 IDC(A) Frequency(MHz) Temp vs DC Current Impedance vs Frequency PE-1210ACC220STS Common mode Differential mode T@25oC 60.0 10000 50.0 T ( o C) 1000 Impedance () 3.0 max Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes 100 22uH 10 22uH 30.0 20.0 1 0.1 40.0 10.0 1 10 2 100 Frequency(MHz) 1,000 10,000 Networking.PulseElectronics.com 0.0 0.0 0.1 0.2 0.3 IDC(A) 0.4 0.5 W717.G (03/19) 1000 1000 Automotive Chip Choke(R) 100 100 EMI Suppression for CAN-Bus Networks 10 10 2-Line Common Mode Chokes 1 0.1 1 Impedance vs Frequency1000 100 0 10 PE-1210ACC510STS Common mode 10,000 10000 0.1 Temp vs DC100 Current 1 10 Differential mode 1000 10000 T@25oC 60.0 , T ( o C) Impedance () 50.0 1,000 100 51uH 30.0 20.0 51uH 10 40.0 10.0 1 1 10 100 Frequency(MHz) 1,000 0.0 10,000 0.0 0.1 0.2 0.3 IDC(A) 0.4 0.5 Temp vs DC Current Impedance vs Frequency PE-1210ACC101STS Common mode 100,000 T@25oC Differential mode 60.0 , 50.0 100uH 1,000 T ( o C) Impedance () 10,000 100 30.0 20.0 10 1 100uH 40.0 10.0 1 10 100 1,000 10,000 Frequency(MHz) 3 Networking.PulseElectronics.com 0.0 0.0 0.1 0.2 0.3 IDC(A) 0.4 0.5 W717.G (03/19) Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes Temp vs DC Current Impedance vs Frequency PE-1812ACC110STS Differential mode T@ 25oC 10,000 60.0 1,000 50.0 11uHmode Differenal Common mode Impedance () Impedance () Common mode T ( o C) 100 10,000 20.0 40.0 100 1 10.0 30.0 10 0.1 10 1 1 Frequency(MHz) 100 0.0 20.0 0.0 1,000 0.2 10.0 Common mode 0.1 10,000.0 1 Differenal mode 10 100 Frequency(MHz) 1,000.0 60.0 1,000 0.0 Impedance vs Frequency 0.4 IDC(A) 0.6 0.8 1.0 T@25 0.0 0.2 0.4 0.6 0.8 1.0 IDC(A) 50.0 Temp vs DC Current 40.0 PE-1812ACC220STS T( ) 100.0 30.0 Common mode 10.0 Differential mode 22uH 1,000 1 10 100 100 10.0 50.0 0.0 40.0 0.0 1,000 T ( o C) 0.1 T@25oC 20.0 60.0 10,000 1.0 Impedance () Impedance( ) 30.0 50.0 T( ) Impedance () 1,00010 11uH T@25 40.0 60.0 Frequency(MHz) 10 22uH 0.2 0.4 0.6 0.8 IDC(A) 30.0 20.0 1 10.0 0.1 10 100 1,000 Frequency(MHz) 4 Networking.PulseElectronics.com 0.0 0.0 0 .2 0.4 IDC(A) 0 .6 0.8 W717.G (03/19) Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes Impedance vs Frequency Temp vs DC Current PE-1812ACC510STS Common mode 100,000 70.0 Dierenal mode 60.0 51uH 50.0 1,000 10,000.0 T ( o C) () Impedance(Impedance ) 10,000 100,000.0 100 51uH 50.0 40.0 10.0 20.0 1 10.0 1 10 1 100 Frequency(MHz) 10 Frequency(MHz) 0.0 10.0 0.0 1,000 0.0 100 Common mode 1,000 0.1 0.0 0.3 0.2 0.1 0.2 0.4 IDC(A) 0.3 0.5 0.4 0.6 0.5 0.6 0.7 0.7 IDC(A) Dierenal mode T@25 100,000.0 60.0 10,000.0 50.0 Impedance vs Frequency Temp vs DC Current 40.0 T( ) PE-1812ACC101STS 1,000.0 Impedance() 30.0 60.0 20.0 30.0 10100.0 1.0 40.0 T@25 70.0 T( ) Common mode 30.0 Common mode 100.0 100,000 Differential mode 10.0 50.0 100uH 1.0 40.0 1 10 100 1,000 Frequency(MHz) 100 100uH 0.0 0.00 0.10 0.20 30.0 0.30 0.40 0.50 0.4 0.5 IDC(A) 20.0 10 1 T ( o C) 1,000 T@25oC 60.020.0 10.0 10,000 Impedance () T@25oC Differential mode 10.0 1 10 100 1,000 Frequency(MHz) 5 Networking.PulseElectronics.com 0.0 0.0 0.1 0.2 0.3 IDC(A) W717.G (03/19) Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes Reliability Test Item 1. High Temperature Exposure Reference documents MIL-STD-202 Method 108 2. Temperature Cycling JESD22 Method JA-104 3. Biased Humidity Test MIL-STD-202 Method 103 4. Operational Life MIL-PRF-27 5. External Visual MIL-STD-883 Method 2009 6. Physical Dimensions JESD22 Method JB-100 7. Resistance to solvents MIL-STD-202 Method 215 8. Vibration Test MIL-STD-202 Method 204 9. Resistance to Soldering Heat Test MIL-STD-202 Method 210 10. Rated Current MIL-STD-202 Method 330 Test Condition 1. Temperature: +125/155C 2. Time: 1000 hours 1. Temperature: -55/40C~125/155C 2. Number of cycles: 1000 cycle 3. Dwell time: 30 minutes 1. Temperature: 855C 2. Time: 1000hours 3. Humidity: 855% RH 1. Temperature: 125 / 155C 2. Time: 1000 hours 3. Apply rated current Inspect product construction, marking and workmanship Verify physical dimensions to the applicable product detail specification Immerse into solvent for 30.5 minutes & brush 10 times for their cycles. 1. Frequency and Amplified: 10-2000-10 Hz, 1.5mm 2. Direction: X, Y, Z 3. Test duration: 2 hours for each direction, 6 hours in total 1. Temperature: 2505C 2. Time: (temp.217C) 92~109 Second 3. IR reflow times: 3 times Apply rated current for 5 seconds. 11. Temperature Rise MIL-PRF-27 Apply rated current for 10 minutes. 12. Over load MIL-PRF-27 Apply twice as rated current for 5 minutes. 13. Solderability Test J-STD-002 14. Electrical Characterization User Spec. 15. Withstanding Voltage Test MIL-STD-202 Method 201 16. Drop JESD22-B111 17. Terminal Strength Test JIS-C-6429 6 1. Baking in pre-testing: 1555C / 16Hours30min. 2. Peak temperature: 245C 3. Time: (temp.217C) 112 Second 4. IR reflow times: 1 time 1. Operating temperature:-55/40C~125/155C 2. Room Temperature: 25C 1. DV: 500V 2. Time: 1 minute Package & Drop down from 1m. In 1 angle 1 ridge & 2 surfaces orientation 1. Apply push force to samples mounted on PCB. 2. Force of 1.8 kg for 601 seconds. Networking.PulseElectronics.com Test Specification 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% Per product specification standard Per product specification standard 1. No body change in appearance 2. No marking blurred. 3. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% The terminal shall be at least 95% covered with fresh solder. 1. No mechanical and electrical damage 2. Inductance shall not change more than 30% 1. During the test no breakdown. 2. The characteristic is normal after test. 1. No case deformation or change in appearance. 2. Inductance shall not change more than 30% After test, inductors shall be on mechanical damge. W717.G (03/19) Automotive Chip Choke(R) EMI Suppression for CAN-Bus Networks 2-Line Common Mode Chokes Tape and Reel Specifications Reel Dimensions (mm) Tape Dimensions (mm) P2 P3 Series Parts per Reel A B C D E W P1 1210 ACC 2000 178 60 13.5 12 9 8 2 4 1812 ACC 500 178 60 13 17 14 12 2 8 III. Description: a. Ferrite drum core construction b. Magnetically shielded c. Enameled copper wire: H class d. Product weight: 0.15g (ref.) e. Moisture sensitivity Level 1 f. Products comply with RoHS' requirements g. Halogen Free available H T 4 2.5 0.26 4 4 0.35 Recommended Solder Heat Resistance Profile IV. General specification: a. Storage temp: -40Cto+125C b. Operating temp: -40Cto+125C (Temp. rise included) c. Resistance to solder heat: 250C 10 secs. For More Information: Americas - prodinfonetworkamericas@pulseelectronics.com | Europe - comms-Apps-Europe@pulseelectronics.com | Asia - prodinfonetworkapac@pulseelectronics.com Performance warranty of products offered on this data sheet is limited to the parameters specified. Data is subject to change without notice. Other brand and product names mentioned herein may be trademarks or registered trademarks of their respective owners. (c) Copyright, 2019. Pulse Electronics, Inc. All rights reserved. 7 Networking.PulseElectronics.com W717.G (03/19)