Advanced Power Electronics Corp. APE1085 Pb Free Plating Product 3A Low Dropout Positive Adjustable or Fixed-Mode Regulator General Description 1. Features * * * * * * * * APE1085 is a low dropout positive adjustable or fixed-mode regulator with minimum of 3.0A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. APE1085 is also well suited for other applications such as VGA cards. APE1085 is guaranteed to have lower than 1.4V dropout at full load current making it ideal to provide well-regulated outputs of 1.25 to 3.3V with 4.7 to 12V input supply. 1.4V maximum dropout at full load current Built-in thermal shutdown Output current limiting Adjustable output voltage or fixed 1.5V, 1.8V, 2.5V, 3.3V, 5.0V Fast transient response Good noise rejection Package : TO252, TO263, TO220 RoHS Compliant Ordering Information APE Low Dropout Regulator 1085 X XX Package Vout H : TO 252-3L Blank : Adj S : TO263-3L 15 = 1.5V P : TO220-3L 18 = 1.8V 25 = 2.5V 33 = 3.3V 50 = 5.0V Block Diagram Vin 3 2 Vout + + 1.25V + CURRENT LIMIT Thermal Shutdown + 1 Adj This datasheet contains new product information. Advanced Power Electronics Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. 200313072-1/10 Advanced Power Electronics Corp. APE1085 Pb Free Plating Product 3A Low Dropout Positive Adjustable or Fixed-Mode Regulator Connection Diagram TO263 TO252 FRONT VIEW FRONT VIEW Vin 3 Vout 2 2 Adj (GND) 1 3 Tab is Vout 1 Vin Vout Adj (GND) Tab is Vout TO220 FRONT VIEW 3 Vin 2 Vout 1 Adj (GND) Tab is Vout Pin Descriptions Pin No. TO263/ PDIP-8 252/220 Name I/O Adj (GND) I 1 1 Vout O 2 2/3/5/6/ 7/8 Vin I 3 4 Function Adjustable (Ground only for fixed mode) A resistor divider from this pin to the Vout pin and ground sets the output voltage. (Ground only for Fixed-Mode) The output of the regulator. A minimum of 10uF (0.15 ESR 20) capacitor must be connected from this pin to ground to insure stability. The input pin of regulator. Typically a large storage capacitor (0.15 ESR 20) is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.4V (1.3V) higher than Vout in order for the device to regulate properly. Advanced Power Electronics Corp. www.a-power.com.tw 2/10 Advanced Power Electronics Corp. APE1085 Pb Free Plating Product 3A Low Dropout Positive Adjustable or Fixed-Mode Regulator Absolute Maximum Ratings Symbol Parameter Rating Vin PD TST DC Supply Voltage Power Dissipation Storage Temperature TOP Operating Junction Temperature Range Electrical Characteristics Sym. Parameter VREF Reference Voltage APE1085-XXX APE1085-1.5 APE1085-1.8 Line Regulation APE1085-2.5 APE1085-3.3 APE1085-5.0 APE1085-Adj APE1085-1.5 Load APE1085-1.8 Regulation APE1085-2.5 Vo JA JC APE1085-3.3 APE1085-5.0 Dropout Voltage Current Limit Minimum Load Current Temperature Stability Thermal Resistance Junction-to-Ambient (No heat sink ;No air flow) Unit -0.3 to 12 V Internally Limited oC -65 to +150 oC 0 to +150 (Under Operating Conditions) Conditions (Notes) o Io=10mA, Tj=25 C, (Vin-Vout)=1.5V IO=10mA, VOUT+1.5V