MP2060 Kool-Pak(R) Clip Mount Power Film Resistor * * * * * * * TO-220 Style Power Resistor Designed for Clip Mounting - Non-Inductive Up to 60 Watts continuous power at +25C case temperature, 0.020 and above. Up to 60 Amps continuous current at +25C case temperature, 0.015 and below. TO-220 Style package utilizes proven power semiconductor thermal solutions. Equivalent to UL94 V-0 flammability rating. Non-inductive design for high speed switching, snubbers and rf applications. Operation up to +150C case temperature. Electrically isolated case. Model Package Resistance 0.005 MP2060 0.010 TO-220 Style 0.015 RATED POWER % 0.020 to 1.00K Derating Curve 100 Power Rating * 36 Watts * 54 Watts * 60 Watts * 60 40 20 25 100 60 Arms 18 Watts 80 0 Max. Current Max. Rating (Amps) Voltage 150 CASE TEMPERATURE, C 60 Arms 60 Arms I = P/R Current Limited Current Limited Current Limited 250 Vrms Thermal Resistance RJC Film (J) to Case (C) 6.94C/Watt 3.47C/Watt 2.31C/Watt 2.08C/Watt * Derating Using Case Temperature (TC): All power and associated overload ratings are derated based upon case temperature using the derating curve. The case temperature is measured at the center of the ceramic mounting surface, with the part properly mounted and under electrical load. Without a heat sink, when in free air at +25C, the MP2060 is rated for 2.5 watts. The thermal design should satisfy the following equation: Case Temperature (Tc) + [Thermal Resistance (RJC) x power applied (Watts)] 150C, considering the full operating temperature range of the application. Mounting Note: Mount on a smooth, clean and flat heat sink surface with a thermal interface material, such as thermal grease. The entire exposed ceramic portion must be in contact with the heat sink. When using a spring clip, it is recommended that a mounting force of 8 to 30 pounds (35 to 130 N) be applied to the center of the package. The clip should be round or smooth in the contact area to avoid concentrating the load on a small point of the plastic body of the package. Another mounting option is to use a pressure bar method which can achieve a greater mounting force with a greater contact area. For additional applications information regarding mounting and pulse handling see the Caddock Applications Notes at caddock.com or contact Applications Engineering. 0.175 0.010 (4.45 0.26) 0.410 0.010 (10.41 0.26) 0.150 0.030 (3.81 0.76) 0.640 0.010 (16.26 0.26) MP2060 50.0 1% 0.100 0.020 (2.54 0.51) 0.500 0.050 (12.70 1.27) 0.050 0.007 (1.27 0.18) 0.200 0.010 (5.08 0.26) DIMENSIONS IN INCHES AND (MILLIMETERS) 0.035 0.007 (0.89 0.18) 0.105 0.010 (2.67 0.26) Standard Resistance Values: Tolerance: 1% Standard (except as noted) 10.0 100 0.33 0.005 5% 12.0 120 0.40 0.010 2% 15.0 150 0.50 0.015 2% 20.0 200 0.75 0.020 25.0 250 1.00 0.025 27.0 300 1.50 0.030 30.0 330 2.00 0.033 33.0 400 2.50 0.040 40.0 470 3.00 0.050 47.0 500 3.30 0.075 50.0 560 4.00 0.10 56.0 750 5.00 0.15 75.0 1.00 K 7.50 0.20 8.00 0.25 0.30 For custom values and tolerances contact Applications Engineering Recommended Limitation of Use: Caddock does not recommend the MP2060 resistors for use in military or space applications. These products are recommended by Caddock for use only in commercial/industrial applications. Caddock has qualified these products, for their intended use, to perform according to catalog specifications. Caddock does not maintain a military and/or space level reliability program for these products. Caddock does not provide support for use of these products in military and space applications. These products have matte tin plated leads (with 100% tin plating), there is no other lead finish offered for the MP2060 Resistors. Any use of these products in a military program, against this recommended limitation of use, will be completely supported by the customer program design activity and component engineering activity based on their complete evaluation and testing, there will be no support provided by Caddock for this use. Space equipment programs (both the engineering phase and the flight phase) must only use selected Caddock products that have been purchased in accordance with NASA GSFC specifications. Applications Engineering 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422 Phone: (541) 496-0700 Fax: (541) 496-0408 (c) 2003-2007 Caddock Electronics, Inc. These products are covered by one or more patents, also patents pending. Specifications: Temperature Coefficient: TC referenced to +25C, R taken at +150C 0.50 ohm and above, -20 to +80 ppm/C 0.050 ohm to 0.49 ohm, 0 to +100 ppm/C 0.015 ohm to 0.049 ohm, 0 to +200 ppm/C 0.005 ohm to 0.014 ohm, 0 to +300 ppm/C Operating Temperature: -55C to +150C Inductance: 10 nH typical in series when measured at the shoulder of the lead. Capacitance: <1 pf typical without heat sink. DWV: 1500 VrmsAC isolation to the mounting surface or a clip in contact with the top surface. Insulation Resistance: 10,000 Megohms, min. The resistor element is electrically isolated from the mounting surface. Momentary Overload: 1.5 times rated power for 5 seconds, R (0.5 percent + 0.0005 ohm) max. Load Stability: 2000 hours at rated power R less than (1 percent +0.0005 ohm). Moisture Resistance: Mil-Std-202, Method 106, R (0.5 percent + 0.0005 ohm) max. Thermal Shock: Mil-Std-202, Method 107, Cond. F, R (0.5 percent + 0.0005 ohm) max. Shock: 100G, Mil-Std-202, Method 213, Cond. I, R (0.4 percent + 0.0005 ohm) max. Vibration, High Frequency: Mil-Std 202, Method 204, Condition D, R (0.4 percent + 0.0005 ohm) max. Terminal Strength: Mil-Std-202, Method 211, Cond. A (Pull Test) 5 lbs., R (0.2 percent + 0.0005 ohm) max. Terminal Material: Solderable Measurement Note: Resistance measurements shall be made at 0.2 inch (5.08 mm) from the resistor body. Ordering Information: Model Number: MP2060 - 0.050 - 1% Resistor Value: Tolerance Packaging Information: MP2060 resistors are pack- aged in plastic shipping tubes, 50 pieces per tube. These resistors are available in a 50 piece minimum quantity and in full tube quantity increments (i.e. 50, 100, 150, etc.). ELECTRONICS, INC. e-mail: caddock@caddock.com * web: www.caddock.com For Caddock Distributors listed by country see caddock.com/contact/dist.html Sales 17271 N. Umpqua Hwy. Roseburg, Oregon 97470-9422 Phone: (541) 496-0700 Fax: (541) 496-0408 LOU-28_IL128.0708