31 MHz, Dual Programmable Filters and Variable Gain Amplifiers ADRF6516 Data Sheet FUNCTIONAL BLOCK DIAGRAM Matched pair of programmable filters and VGAs Continuous gain control range: 50 dB Digital gain control: 15 dB 6-pole Butterworth filter: 1 MHz to 31 MHz in 1 MHz steps, 1 dB corner frequency Preamplifier and postamplifier gain steps IMD3: >65 dBc for 1.5 V p-p composite output HD2, HD3: >65 dBc for 1.5 V p-p output Differential input and output Flexible output and input common-mode ranges Optional dc offset compensation loop SPI programmable filter corners and gain steps Power-down feature Single 3.3 V supply operation APPLICATIONS ENBL INP1 VPS COM VICM OFS1 VPS VPSD OPP1 COMD OPM1 LE COM CLK GAIN SPI DATA VOCM SDO COM COM OPM2 VPS ADRF6516 COM Baseband IQ receivers Diversity receivers ADC drivers Point-to-point and point-to-multipoint radio Instrumentation Medical INM1 INP2 INM2 VPS COM OFDS OFS2 VPS OPP2 09422-001 FEATURES Figure 1. GENERAL DESCRIPTION The ADRF6516 is a matched pair of fully differential, low noise and low distortion programmable filters and variable gain amplifiers (VGAs). Each channel is capable of rejecting large out-of-band interferers while reliably boosting the desired signal, thus reducing the bandwidth and resolution requirements on the analog-to-digital converters (ADCs). The excellent matching between channels and their high spurious-free dynamic range over all gain and bandwidth settings make the ADRF6516 ideal for quadrature-based (IQ) communication systems with dense constellations, multiple carriers, and nearby interferers. The filters provide a six-pole Butterworth response with 1 dB corner frequencies programmable through the SPI port from 1 MHz to 31 MHz in 1 MHz steps. The preamplifier that precedes the filters offers a SPI-programmable option of either 3 dB or 6 dB of gain. The preamplifier sets a differential input impedance of 1600 and has a common-mode voltage that defaults to VPS/2 but can be driven from 1.1 V to 1.8 V. Rev. C The variable gain amplifiers that follow the filters provide 50 dB of continuous gain control with a slope of 15.5 mV/dB. Their maximum gains can be programmed to various values through the SPI. The output buffers provide a differential output impedance of 30 and are capable of driving 2 V p-p into 1 k loads. The output common-mode voltage defaults to VPS/2, but it can be adjusted down to 700 mV by driving the high impedance VOCM pin. Independent, built-in dc offset compensation loops can be disabled if fully dc-coupled operation is desired. The high-pass corner frequency is defined by external capacitors on the OFS1 and OFS2 pins and the VGA gain. The ADRF6516 operates from a 3.15 V to 3.45 V supply and consumes a maximum supply current of 360 mA when programmed to the highest bandwidth setting. When disabled, it consumes <9 mA. The ADRF6516 is fabricated in an advanced silicon-germanium BiCMOS process and is available in a 32-lead, exposed paddle LFCSP. Performance is specified over the -40C to +85C temperature range. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2010-2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADRF6516 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Maximizing the Dynamic Range.............................................. 19 Applications ....................................................................................... 1 Key Parameters for Quadrature-Based Receivers .................. 20 Functional Block Diagram .............................................................. 1 Applications Information .............................................................. 21 General Description ......................................................................... 1 Basic Connections ...................................................................... 21 Revision History ............................................................................... 2 Supply Decoupling ..................................................................... 21 Specifications..................................................................................... 3 Input Signal Path ........................................................................ 21 Timing Diagrams.......................................................................... 5 Output Signal Path ..................................................................... 21 Absolute Maximum Ratings............................................................ 6 DC Offset Compensation Loop Enabled ................................ 21 ESD Caution .................................................................................. 6 Common-Mode Bypassing ....................................................... 21 Pin Configuration and Function Descriptions ............................. 7 Serial Port Connections............................................................. 22 Typical Performance Characteristics ............................................. 8 Enable/Disable Function ........................................................... 22 Register Map and Codes ................................................................ 15 Error Vector Magnitude (EVM) Performance ........................... 22 Theory of Operation ...................................................................... 16 EVM Test Setup .......................................................................... 22 Input Buffers ............................................................................... 16 Effect of Filter Bandwidth on EVM ......................................... 22 Programmable Filters ................................................................. 16 Effect of Output Voltage Levels on EVM ................................ 23 Variable Gain Amplifiers (VGAs) ............................................ 17 Effect of COFS Value on EVM..................................................... 23 Output Buffers/ADC Drivers ................................................... 17 Evaluation Board ............................................................................ 24 DC Offset Compensation Loop................................................ 17 Evaluation Board Control Software ......................................... 24 Programming the Filters and Gains ......................................... 18 Schematics and Artwork ........................................................... 25 Noise Characteristics ................................................................. 18 Outline Dimensions ....................................................................... 29 Distortion Characteristics ......................................................... 19 Ordering Guide .......................................................................... 29 REVISION HISTORY 8/2017--Rev. B to Rev. C Change to Figure 4 ........................................................................... 7 Updated Outline Dimensions ...................................................... 29 Changes to Ordering Guide Section ............................................ 29 2/2012--Rev. A to Rev. B Changes to Figure 57 ...................................................................... 24 Changes to Figure 58 ...................................................................... 25 Added Figure 59.............................................................................. 26 Changes to Figure 60 and Figure 61 ............................................. 27 Changes to Table 6 .......................................................................... 27 9/2011--Revision A: Initial Version Rev. C | Page 2 of 29 Data Sheet ADRF6516 SPECIFICATIONS VPS = 3.3 V, TA = 25C, ZLOAD = 1 k, digital gain code = 111, unless otherwise noted. Table 1. Parameter FREQUENCY RESPONSE Low-Pass Corner Frequency, fC Step Size Corner Frequency Absolute Accuracy Corner Frequency Matching Pass-Band Ripple Gain Matching Group Delay Variation Corner Frequency = 1 MHz Corner Frequency = 31 MHz Group Delay Matching Corner Frequency = 1 MHz Corner Frequency = 31 MHz Stop-Band Rejection Relative to Pass Band INPUT STAGE Maximum Input Swing Differential Input Impedance Input Common-Mode Range VICM Output Impedance GAIN CONTROL Voltage Gain Range Gain Slope Gain Error OUTPUT STAGE Maximum Output Swing Differential Output Impedance Output DC Offset Output Common-Mode Range Test Conditions/Comments Min 6-pole Butterworth filter, 0.5 dB bandwidth 1 Over operating temperature range Channel A and Channel B at same gain and bandwidth settings Channel A and Channel B at same gain and bandwidth settings From midband to peak Second Harmonic, HD2 Third Harmonic, HD3 Max Unit 31 1 15 MHz MHz % fC 0.5 % fC 0.5 0.1 dB p-p dB 135 11 ns ns 5 0.2 ns ns 30 75 dB dB 1 1600 1.65 VPS/2 7 V p-p V V k Channel A and Channel B at same gain 2 x fC 5 x fC INP1, INM1, INP2, INM2, VICM pins At minimum gain, VGAIN = 0 V 0.4 V p-p input voltage, HD3 > 65 dBc Input pins left floating GAIN pin VGAIN from 0 V to 1 V 1.1 -5 VGAIN from 300 mV to 800 mV OPP1, OPM1, OPP2, OPM2, VOCM pins At maximum gain, RLOAD = 1 k HD2 > 65 dBc, HD3 > 65 dBc Inputs shorted, offset loop disabled 0.7 VOCM pin left floating VOCM Input Impedance NOISE/DISTORTION Corner Frequency = 1 MHz Output Noise Density Typ Gain = 0 dB at fC/2 Gain = 20 dB at fC/2 Gain = 40 dB at fC/2 250 kHz fundamental, 1.5 V p-p output voltage Gain = 5 dB Gain = 40 dB 250 kHz fundamental, 1.5 V p-p output voltage Gain = 5 dB Gain = 40 dB Rev. C | Page 3 of 29 1.8 15.5 0.2 +45 dB mV/dB dB 2 1.5 30 35 1.65 VPS/2 23 V p-p V p-p mV V V k 2.8 -141 -131 -112 dBV/Hz dBV/Hz dBV/Hz 82 68 dBc dBc 71 56 dBc dBc ADRF6516 Parameter IMD3 IMD3 with Input CW Blocker Corner Frequency = 31 MHz Output Noise Density Second Harmonic, HD2 Third Harmonic, HD3 IMD3 IMD3 with Input CW Blocker DIGITAL LOGIC Input High Voltage, VINH Input Low Voltage, VINL Input Current, IINH/IINL Input Capacitance, CIN SPI TIMING fSCLK tDH tDS tLH tLS tPW tD POWER AND ENABLE Supply Voltage Range Total Supply Current Disable Current Disable Threshold Enable Response Time Disable Response Time Data Sheet Test Conditions/Comments f1 = 500 kHz, f2 = 550 kHz, 1.5 V p-p composite output voltage Gain = 5 dB Gain = 35 dB f1 = 500 kHz, f2 = 550 kHz, 1.5 V p-p composite output, gain = 5 dB; blocker at 5 MHz, 10 dBc relative to two-tone composite output voltage Min Midband, gain = 0 dB Midband, gain = 20 dB Midband, gain = 40 dB 8 MHz fundamental, 1.5 V p-p output voltage Gain = 5 dB Gain = 40 dB 8 MHz fundamental, 1.5 V p-p output voltage Gain = 5 dB Gain = 40 dB f1 = 14 MHz, f2 = 15 MHz, 1.5 V p-p composite output voltage Gain = 5 dB Gain = 35 dB f1 = 14 MHz, f2 = 15 MHz, 1.5 V p-p composite output, gain = 5 dB; blocker at 150 MHz, 10 dBc relative to two-tone composite output voltage LE, CLK, DATA, SDO, OFDS pins LE, CLK, DATA, SDO pins (see Figure 2 and Figure 3) 1/tSCLK DATA hold time DATA setup time LE hold time LE setup time CLK high pulse width CLK to SDO delay VPS, VPSD, COM, COMD, ENBL pins 3.15 ENBL = 3.3 V Corner frequency = 31 MHz Corner frequency = 1 MHz ENBL = 0 V Delay following ENBL low-to-high transition Delay following ENBL high-to-low transition Rev. C | Page 4 of 29 Typ Max Unit 61 42.5 40 dBc dBc dBc -143.5 -139 -125 dBV/Hz dBV/Hz dBV/Hz 68 70 dBc dBc 55 75 dBc dBc 55 77.5 55 dBc dBc dBc >2 <0.8 <1 2 V V A pF 20 5 5 5 5 5 5 MHz ns ns ns ns ns ns 3.3 360 330 9 1.6 20 300 3.45 V mA mA mA V s ns Data Sheet ADRF6516 TIMING DIAGRAMS tPW tCLK CLK tLH tLS LE tDS DATA tDH WRITE BIT B2 LSB B3 B4 B5 B6 B7 MSB MSB - 2 09422-003 NOTES 1. THE FIRST DATA BIT DETERMINES WHETHER THE PART IS WRITING TO OR READING FROM THE INTERNAL 8-BIT REGISTER. FOR A WRITE OPERATION, THE FIRST BIT SHOULD BE A LOGIC 1. THE 8-BIT WORD IS THEN WRITTEN TO THE DATA PIN ON CONSECUTIVE RISING EDGES OF THE CLOCK. Figure 2. Write Mode Timing Diagram tCLK tD tPW CLK tLH tLS LE DATA SDO tDH READ BIT DON'T CARE LSB DON'T CARE B2 DON'T CARE B3 DON'T CARE DON'T CARE B4 B5 DON'T CARE B6 DON'T CARECARE DON'T CARE DON'T B7 MSB NOTES 1. THE FIRST DATA BIT DETERMINES WHETHER THE PART IS WRITING TO OR READING FROM THE INTERNAL 8-BIT REGISTER. FOR A READ OPERATION, THE FIRST BIT SHOULD BE A LOGIC 0. THE 8-BIT WORD IS THEN REGISTERED AT THE SDO PIN ON CONSECUTIVE FALLING EDGES OF THE CLOCK. Figure 3. Read Mode Timing Diagram Rev. C | Page 5 of 29 09422-004 tDS ADRF6516 Data Sheet ABSOLUTE MAXIMUM RATINGS Table 2. Parameter Supply Voltages, VPS, VPSD ENBL, OFDS, LE, CLK, DATA, SDO INP1, INM1, INP2, INM2 OPP1, OPM1, OPP2, OPM2 OFS1, OFS2 GAIN Internal Power Dissipation JA (Exposed Pad Soldered to Board) Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Lead Temperature (Soldering 60 sec) Rating 3.45 V VPSD + 0.5 V VPS + 0.5 V VPS + 0.5 V VPS + 0.5 V VPS + 0.5 V 1.25 W 37.4C/W 150C -40C to +85C -65C to +150C 300C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. ESD CAUTION Rev. C | Page 6 of 29 Data Sheet ADRF6516 32 31 30 29 28 27 26 25 ENBL INP1 INM1 VPS COM VICM OFS1 VPS PIN CONFIGURATION AND FUNCTION DESCRIPTIONS 1 2 3 4 5 6 7 8 ADRF6516 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 OPP1 OPM1 COM GAIN VOCM COM OPM2 OPP2 NOTES 1. CONNECT THE EXPOSED PADDLE TO A LOW IMPEDANCE GROUND PAD. 09422-002 COM INP2 INM2 VPS COM OFDS OFS2 VPS 9 10 11 12 13 14 15 16 VPSD COMD LE CLK DATA SDO COM VPS Figure 4. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 2 3 4 5 6 7, 9, 13, 19, 22, 28 8, 12, 16, 25, 29 10, 11, 30, 31 14 15, 26 17, 18, 23, 24 20 21 27 32 Mnemonic VPSD COMD LE CLK DATA SDO COM VPS INP2, INM2, INM1, INP1 OFDS OFS2, OFS1 OPP2, OPM2, OPM1, OPP1 VOCM GAIN VICM ENBL EP Description Digital Positive Supply Voltage: 3.15 V to 3.45 V. Digital Common. Connect to external circuit common using the lowest possible impedance. Latch Enable. SPI programming pin. TTL levels: VLOW < 0.8 V, VHIGH > 2 V. SPI Port Clock. TTL levels: VLOW < 0.8 V, VHIGH > 2 V. SPI Data Input. TTL levels: VLOW < 0.8 V, VHIGH > 2 V. SPI Data Output. TTL levels: VLOW < 0.8 V, VHIGH > 2 V. Analog Common. Connect to external circuit common using the lowest possible impedance. Analog Positive Supply Voltage: 3.15 V to 3.45 V. Differential Inputs. 1600 input impedance. Offset Compensation Loop Disable. Pull high to disable the offset compensation loop. Offset Compensation Loop Capacitors. Connect capacitors to circuit common. Differential Outputs. 30 output impedance. Common-mode range is 0.7 V to 2.8 V; default is VPS/2. Output Common-Mode Setpoint. Defaults to VPS/2 if left floating. Analog Gain Control. 0 V to 1 V, 15.5 mV/dB gain scaling. Input Common-Mode Voltage. VPS/2 V reference. Use to reference the optimal common-mode drive to the differential inputs. Chip Enable. Pull high to enable. Exposed Paddle. Connect the exposed paddle to a low impedance ground pad. Rev. C | Page 7 of 29 ADRF6516 Data Sheet TYPICAL PERFORMANCE CHARACTERISTICS VPS = 3.3 V, TA = 25C, ZLOAD = 1 k, digital gain code = 111, unless otherwise noted. BANDWIDTH = 31MHz 45 +25C VPS = 3.15V, 3.3V, 3.45V GAIN ERROR (dB) -40C VPS = 3.15V, 3.3V, 3.45V 20 +85C VPS = 3.15V, 3.3V, 3.45V 15 10 5 0 -10 0 100 200 300 400 500 600 700 800 900 1000 VGAIN (mV) 09422-005 -5 0 300 400 500 600 700 800 900 1000 8 -5 BANDWIDTH = 31MHz 7 -6 6 -7 DIGITAL GAIN = 111 AMPLITUDE (dB) -8 10 FREQUENCY (MHz) 100 5 -9 4 -10 3 -11 2 DIGITAL GAIN = 011 -12 1 -13 0 -14 -1 -15 09422-006 GAIN (dB) 200 Figure 8. Gain Conformance vs. VGAIN over Supply and Temperature (Bandwidth Setting = 31 MHz) BANDWIDTH = 31MHz 1 0 Figure 6. Gain vs. Frequency over VGAIN (Bandwidth Setting = 31 MHz) 5 10 15 20 FREQUENCY (MHz) 25 30 35 -2 Figure 9. Gain Step and Gain Error vs. Frequency (Bandwidth Setting = 31 MHz, VGAIN = 0 V) 0.25 0 14 BANDWIDTH = 31MHz BANDWIDTH = 31MHz 0.20 -5 0.15 AMPLITUDE (dB) 0.10 0.05 0 -0.05 -0.10 13 DIGITAL GAIN = 011 -10 12 -15 11 -20 10 DIGITAL GAIN = 000 -0.15 -25 9 -0.20 -0.25 0 100 200 300 400 500 600 VGAIN (mV) 700 800 900 1000 09422-007 GAIN MISMATCH (dB) 100 -40C VPS = 3.15V, 3.3V, 3.45V VGAIN (mV) Figure 5. In-Band Gain vs. VGAIN over Supply and Temperature (Bandwidth Setting = 31 MHz) 50 45 40 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 -35 -40 -45 -50 +25C VPS = 3.15V, 3.3V, 3.45V GAIN STEP (dB) 25 +85C VPS = 3.15V, 3.3V, 3.45V Figure 7. Gain Matching vs. VGAIN (Bandwidth Setting = 31 MHz) -30 0 5 10 15 20 25 30 FREQUENCY (MHz) Figure 10. Gain Step and Gain Error vs. Frequency (Bandwidth Setting = 31 MHz, VGAIN = 0 V) Rev. C | Page 8 of 29 8 35 09422-010 GAIN (dB) 30 09422-009 35 BANDWIDTH = 31MHz GAIN STEP (dB) 40 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -0.5 -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 -5.0 09422-008 50 Data Sheet ADRF6516 20 40 BANDWIDTH = 31MHz BANDWIDTH = 31MHz 38 15 36 10 -40C, VPS = 3.15V, 3.3V, 3.45V GAIN (dB) 0 -5 DIGITAL GAIN = 000 32 30 28 +25C, VPS = 3.15V, 3.3V, 3.45V 26 -10 +85C, VPS = 3.15V, 3.3V, 3.45V 24 -15 22 0 5 10 15 20 25 GAIN (dB) 30 35 40 20 09422-011 -20 4 2 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 VGAIN (mV) 09422-014 OP1dB (dBV) 34 DIGITAL GAIN = 111 5 Figure 14. Frequency Response over Supply and Temperature (Bandwidth Setting = 31 MHz, Gain = 30 dB) Figure 11. Output P1dB vs. Gain at 15 MHz (Bandwidth Setting = 31 MHz) 40 1000 35 900 30 800 25 700 20 15 10 5 600 500 400 300 0 200 -5 100 1 10 100 FREQUENCY (MHz) BW = 10MHz BW = 31MHz BW = 20MHz BW = 5MHz 0 0.3 09422-012 -10 BW = 1MHz 3 30 50 FREQUENCY (MHz) Figure 12. Frequency Response vs. Bandwidth Setting (Gain = 30 dB), Log Scale 09422-015 GROUP DELAY (ns) GAIN (dB) GAIN = 20dB Figure 15. Group Delay vs. Frequency (Gain = 20 dB) 40 2.0 BANDWIDTH = 31MHz 35 1.5 GROUP DELAY MISMATCH (ns) 30 20 15 10 5 0 1.0 0.5 0 GAIN = 20dB -0.5 -1.0 GAIN = 40dB -1.5 -10 0 10 20 30 40 50 60 FREQUENCY (MHz) 70 80 90 100 09422-013 -5 Figure 13. Frequency Response vs. Bandwidth Setting (Gain = 30 dB), Linear Scale -2.0 0.3 3 FREQUENCY (MHz) Figure 16. Group Delay Matching vs. Frequency (Bandwidth Setting = 31 MHz) Rev. C | Page 9 of 29 30 09422-016 GAIN (dB) 25 ADRF6516 Data Sheet 5 90 VOCM = 0.9V VOCM = 1.2V VOCM = 1.4V VOCM = 1.65V BANDWIDTH = 1MHz 80 GAIN = 0dB 3 2 HD2 AT 16MHz (dBc) GROUP DELAY MISMATCH (ns) 4 1 0 -1 GAIN = 20dB -2 -3 70 60 50 40 0.8 0.6 0.4 1.0 1.2 1.4 FREQUENCY (MHz) 30 09422-017 -5 0.2 Figure 17. IQ Group Delay Matching vs. Frequency (Bandwidth Setting = 1 MHz) 0.5 1.0 10 15 20 25 30 35 40 45 Figure 20. HD2 vs. Gain over Output Common-Mode Voltage (Bandwidth Setting = 31 MHz, 1.5 V p-p, 8 MHz CW Fundamental Output) 90 2.5 2.0 1.5 5 GAIN (dB) FREQUENCY (MHz) 0 0 09422-020 -4 3.0 0.50 80 0.25 BANDWIDTH = 1MHz BANDWIDTH = 30MHz 0 60 50 40 +25C, VPS = 3.3V +25C, VPS = 3.15V +25C, VPS = 3.45V +85C, VPS = 3.3V +85C, VPS = 3.15V +85C, VPS = 3.45V -40C, VPS = 3.3V -40C, VPS = 3.15V -40C, VPS = 3.45V 30 20 -0.25 10 -0.50 0 20 10 15 FREQUENCY (MHz) 5 25 30 0 5 10 15 09422-018 0 20 25 30 35 40 45 GAIN (dB) 09422-022 HD3 AT 24MHz (dBc) AMPLITUDE MISMATCH (dB) 70 Figure 21. HD3 vs. Gain over Supply and Temperature (Bandwidth Setting = 31 MHz, 1.5 V p-p, 8 MHz CW Fundamental Output) Figure 18. IQ Amplitude Matching vs. Frequency 90 90 VOCM = 0.9V VOCM = 1.2V VOCM = 1.4V VOCM = 1.65V 80 80 HD3 AT 24MHz (dBc) 60 50 40 +25C, VPS = 3.3V +25C, VPS = 3.15V +25C, VPS = 3.45V +85C, VPS = 3.3V +85C, VPS = 3.15V +85C, VPS = 3.45V -40C, VPS = 3.3V -40C, VPS = 3.15V -40C, VPS = 3.45V 20 10 0 0 5 10 15 70 60 50 40 20 25 GAIN (dB) 30 35 40 45 30 Figure 19. HD2 vs. Gain over Supply and Temperature (Bandwidth Setting = 31 MHz, 1.5 V p-p, 8 MHz CW Fundamental Output) 0 5 10 15 20 25 GAIN (dB) 30 35 40 45 09422-023 30 09422-019 HD2 AT 16MHz (dBc) 70 Figure 22. HD3 vs. Gain over Output Common-Mode Voltage (Bandwidth Setting = 31 MHz, 1.5 V p-p, 8 MHz CW Fundamental Output) Rev. C | Page 10 of 29 Data Sheet ADRF6516 110 GAIN = 0dB, HD2 GAIN = 0dB, HD3 GAIN = 10dB, HD2 GAIN = 10dB, HD3 75 100 90 80 70 IMD3 (dBc) HARMONIC DISTORTION (dBc) 80 65 60 70 60 GAIN = 30dB GAIN = 20dB GAIN = 10dB GAIN = 0dB 50 40 30 55 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 VICM (V) 10 09422-024 50 0.50 BANDWIDTH = 31MHz f1 = 14MHz, f2 = 15MHz 40 DIGITAL GAIN = 000 3.5 4.0 90 80 35 DIGITAL GAIN = 111 70 25 20 15 60 50 40 GAIN = 40dB GAIN = 30dB GAIN = 20dB GAIN = 10dB GAIN = 0dB 30 10 20 5 10 5 10 15 20 30 25 35 40 45 50 GAIN (dB) 0 0 45 40 -40C +85C IMD2 AT 15MHz (dBV) 35 30 +25C 25 20 15 10 5 10 15 20 25 30 35 40 45 GAIN (dB) 50 09422-026 5 0 1.0 2.5 3.0 1.5 2.0 COMPOSITE OUTPUT VOLTAGE (V p-p) 3.5 4.0 Figure 27. In-Band Third-Order Intermodulation Distortion (Bandwidth Setting = 31 MHz, Digital Gain = 111) Figure 24. In-Band OIP3 vs. Gain (Bandwidth Setting = 31 MHz) BANDWIDTH = 31MHz f1 = 14MHz, f2 = 15MHz DIGITAL GAIN = 111 0.5 70 60 BANDWIDTH = 31MHz 50 40 30 20 10 0 -10 -20 2:1 SLOPE -30 -40 -50 -60 -70 -80 -90 -100 -110 -120 -130 OUT-OF-BAND IIP2 -140 PREAMP GAIN = 6dB -150 PREAMP GAIN = 3dB -160 -170 5 15 25 35 45 55 -55 -45 -35 -25 -15 -5 INPUT LEVEL AT 115MHz AND 130MHz (dBV/TONE) Figure 28. Out-of-Band IIP2, IMD2 Tone at Midband (Bandwidth Setting = 31 MHz) Figure 25. In-Band OIP3 vs. Gain over Temperature (Bandwidth Setting = 31 MHz) Rev. C | Page 11 of 29 65 09422-029 0 09422-025 0 09422-028 IMD3 (dBc) 30 OIP3 (dBV) 1.0 1.5 2.0 2.5 3.0 COMPOSITE OUTPUT VOLTAGE (V p-p) 100 45 OIP3 (dBV) 0.5 Figure 26. In-Band Third-Order Intermodulation Distortion (Bandwidth Setting = 31 MHz, Digital Gain = 000) Figure 23. HD2 and HD3 vs. Input Common-Mode Voltage (Bandwidth Setting = 31 MHz, 0.4 V p-p Input Level) 0 0 09422-027 20 Data Sheet -110 10 BANDWIDTH = 31MHz 0 -10 -20 -30 -40 -50 3:1 SLOPE -60 -70 -80 -90 -100 -110 -120 OUT-OF-BAND IIP3 -130 -140 PREAMP GAIN = 6dB -150 PREAMP GAIN = 3dB -160 -55 -50 -45 -40 -35 -30 -25 -20 -15 -10 -5 OUTPUT NOISE DENSITY (dBV/Hz) -115 -120 -130 -135 -140 -145 -150 0 5 -160 -20 30 20 10 GAIN (dB) 0 40 50 Figure 32. Output Noise Density vs. Analog Gain over Digital Gain (Bandwidth Setting = 31 MHz, Measured at 1/2 Bandwidth) Figure 29. Out-of-Band IIP3, IMD3 Tone at Midband (Bandwidth Setting = 31 MHz) 60 -100 -105 OUTPUT NOISE DENSITY (dBV/Hz) 55 DIGITAL GAIN = 000 DIGITAL GAIN = 100 DIGITAL GAIN = 110 DIGITAL GAIN = 111 50 45 40 35 30 25 20 15 -110 1MHz 2MHz 4MHz 8MHz 16MHz 31MHz -115 -120 -125 -130 -135 -140 10 0 20 30 50 40 GAIN (dB) -150 09422-031 -10 -5 0 5 10 15 25 20 GAIN (dB) 30 35 40 45 50 09422-034 -145 10 -20 Figure 33. Output Noise Density vs. Gain over Bandwidth Setting (Digital Gain = 111, Measured at 1/2 Bandwidth) Figure 30. Noise Figure vs. Analog Gain over Digital Gain (Bandwidth Setting = 31 MHz, Noise Figure at 1/2 Bandwidth) -100 50 1MHz 2MHz 4MHz 8MHz 16MHz 31MHz OUTPUT NOISE DENSITY (dBV/Hz) 45 GAIN = 40dB -105 40 35 30 25 BANDWIDTH = 1MHz DIGITAL GAIN = 111 -110 -115 -120 -125 GAIN = 20dB -130 -135 -140 GAIN = 0dB -145 5 15 25 35 45 GAIN (dB) -150 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 FREQUENCY (MHz) 09422-032 20 -5 Figure 34. Output Noise Density vs. Frequency (Bandwidth Setting = 1 MHz, Digital Gain = 111) Figure 31. Noise Figure vs. Gain over Bandwidth Setting (Digital Gain = 111, Noise Figure at 1/2 Bandwidth) Rev. C | Page 12 of 29 09422-052 NF (dB) -10 09422-033 -155 INPUT LEVEL AT 115MHz AND 215MHz (dBV/TONE) NF (dB) DIGITAL GAIN = 000 DIGITAL GAIN = 100 DIGITAL GAIN = 110 DIGITAL GAIN = 111 -125 09422-030 IMD3 AT 15MHz (dBV) ADRF6516 Data Sheet ADRF6516 50 35 BANDWIDTH = 31MHz BANDWIDTH = 31MHz DIGITAL GAIN = 111 -115 GAIN = 40dB 40 30 30 25 20 20 10 15 -125 -130 GAIN = 20dB -135 LSERIES OUT (nH) -120 RSERIES OUT () OUTPUT NOISE DENSITY (dBV/Hz) -110 -140 GAIN = 0dB -145 25 15 35 45 65 55 75 85 95 FREQUENCY (MHz) 0 10 5 30 FREQUENCY (MHz) 120 -90 BANDWIDTH = 31MHz DIGITAL GAIN = 111 100 -100 GAIN = 40dB ISOLATION (dB) -105 -110 -115 GAIN = 40dB -120 -125 GAIN = 20dB 80 GAIN = 0dB 60 40 -130 GAIN = 20dB -135 20 GAIN = 0dB -145 -45 -40 -30 -35 -25 -20 BANDWIDTH = 31MHz -15 -10 -5 BLOCKER LEVEL AT 150MHz (dBV rms) 0 0 25 20 15 10 30 FREQUENCY (MHz) Figure 36. Output Noise Density vs. Input CW Blocker Level (Bandwidth Setting = 31 MHz, Blocker at 150 MHz) Figure 39. Channel Isolation, Output to Output, vs. Frequency (Bandwidth Setting = 31 MHz) 365 40 2500 5 09422-040 -140 09422-037 OUTPUT NOISE DENSITY AT 15MHz (dBV/Hz) 25 20 Figure 38. Output Impedance vs. Frequency (Bandwidth Setting = 31 MHz) Figure 35. Output Noise Density vs. Frequency (Bandwidth Setting = 31 MHz, Digital Gain = 111) -95 15 10 09422-039 5 09422-051 -150 BANDWIDTH = 31MHz 360 ISUPPLY (mA) CIN (pF) 345 340 335 -20 1000 350 DIGITAL GAIN = 000 DIGITAL GAIN = 111 330 500 0 5 10 15 20 25 FREQUENCY (MHz) Figure 37. Input Impedance vs. Frequency (Bandwidth Setting = 31 MHz) -40 30 325 0 5 10 15 20 BANDWIDTH (MHz) 25 30 35 09422-041 0 1500 09422-038 RIN () 355 20 2000 Figure 40. Current Consumption at Minimum and Maximum Digital Gain vs. Bandwidth (Bandwidth Setting = 31 MHz, Gain = 30 dB) Rev. C | Page 13 of 29 ADRF6516 Data Sheet 370 70 BANDWIDTH = 31MHz BANDWIDTH = 31MHz 368 60 GAIN = 40dB 366 50 GAIN = 20dB CMRR (dB) ISUPPLY (mA) 364 362 360 40 30 358 20 356 0 20 40 TEMPERATURE (C) 60 80 100 0 Figure 41. Current Consumption at Minimum and Maximum Digital Gain vs. Temperature (Bandwidth Setting = 31 MHz, Gain = 30 dB) BANDWIDTH = 31MHz 20dB GAIN STEP VGAIN = 750mV TO 450mV 200ns/DIV 09422-143 28MHz SIGNAL = 60mV p-p TO 600mV p-p Figure 42. Gain Step Response Rev. C | Page 14 of 29 0 5 10 15 20 FREQUENCY (MHz) 25 30 Figure 43. Common-Mode Rejection Ratio (CMRR) vs. Frequency (Bandwidth Setting = 31 MHz) 09422-144 -20 09422-042 352 -40 10 DIGITAL GAIN = 000 DIGITAL GAIN = 111 354 Data Sheet ADRF6516 REGISTER MAP AND CODES The filter frequency, preamplifier gain, postamplifier gain, and VGA maximum gain can be programmed using the SPI interface. Table 4 provides the bit map for the internal 8-bit register of the ADRF6516. The preamplifier, postamplifier, and VGA maximum gain code bits (Bits[B3:B1]) are referred to elsewhere in this data sheet as Digital Gain Code 000 through Digital Gain Code 111. Table 4. Register Map MSB B8 B7 B6 B5 Filter frequency code B4 B3 Preamplifier gain code 0 = 3 dB 1 = 6 dB See Table 5 B2 Postamplifier gain code 0 = 6 dB 1 = 12 dB LSB B1 VGA max gain code 0 = 22 dB 1 = 28 dB Table 5. Frequency Code vs. Corner Frequency Lookup Table 5-Bit Binary Frequency Code1 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 Corner Frequency (MHz) No signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 5-Bit Binary Frequency Code1 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 1 MSB first. Rev. C | Page 15 of 29 Corner Frequency (MHz) 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 ADRF6516 Data Sheet THEORY OF OPERATION The ADRF6516 consists of a matched pair of buffered, programmable filters followed by a cascade of two variable gain amplifiers and output ADC drivers. The block diagram of a single channel is shown in Figure 44. The programmability of the bandwidth and of the pre- and postfiltering gain through the SPI interface offers great flexibility when coping with signals of varying levels in the presence of noise and large, undesired signals nearby. The entire differential signal chain is dc-coupled with flexible interfaces at the input and output. The bandwidth and gain setting controls for the two channels are shared, ensuring close matching of their magnitude and phase responses. The ADRF6516 can be fully disabled through the ENBL pin. 25dB VGA 6dB/12dB ADC DRIVER The filters are designed so that the Butterworth prototype filter shape and group delay responses vs. frequency are retained for any bandwidth setting. Figure 45 and Figure 46 illustrate the ideal six-pole Butterworth magnitude and group delay responses, respectively. The group delay, g, is defined as 3dB/6dB 6dB/12dB BASEBAND OUTPUTS 11dB/14dB BASEBAND INPUTS The integrated programmable filter is the key signal processing function in the ADRF6516. The filters follow a six-pole Butterworth prototype response that provides a compromise between band rejection, ripple, and group delay. The 0.5 dB bandwidth is programmed from 1 MHz to 31 MHz in 1 MHz steps via the serial programming interface (SPI), as described in the Programming the Filters and Gains section. g = -/ SPI INTERFACE 09422-046 GAIN AND FILTER ANALOG OUTPUT PROGRAMMING GAIN CONTROL COMMON-MODE SPI BUS 15mV/dB CONTROL Figure 44. Signal Path Block Diagram for a Single Channel of the ADRF6516 Filtering and amplification are fundamental operations in any signal processing system. Filtering is necessary to select the intended signal while rejecting out-of-band noise and interferers. Amplification increases the level of the desired signal to overcome noise added by the system. When used together, filtering and amplification can extract a low level signal of interest in the presence of noise and out-of-band interferers. Such analog signal processing alleviates the requirements on the analog, mixed signal, and digital components that follow. INPUT BUFFERS The input buffers provide a convenient interface to the sensitive filter sections that follow. They set a differential input impedance of 1600 and float to a common-mode voltage near VPS/2. The inputs can be dc-coupled or ac-coupled. If using direct dc coupling, the common-mode voltage presented to the inputs must be approximately VPS/2 to maximize the input swing capacity. where: is the phase in radians. = 2f (the frequency in radians/sec). Note that for a frequency scaled filter prototype, the absolute magnitude of the group delay scales inversely with the bandwidth; however, the shape is retained. For example, the peak group delay for a 28 MHz bandwidth setting is 14x less than for a 2 MHz setting (see Figure 46). 0 -20 For a 3.3 V supply, the common-mode voltage can range from 1.1 V to 1.8 V while maintaining a >65 dBc HD3 for a 400 mV p-p input signal. The VICM pin provides the optimal midsupply common-mode voltage and can be used as a reference for the driving circuit. The VICM voltage is not buffered and must be sensed at a high impedance point to prevent it from being loaded down. Rev. C | Page 16 of 29 -40 -60 -80 -100 -120 -140 -160 -180 1M 10M 100M 1G FREQUENCY (Hz) Figure 45. Sixth-Order Butterworth Magnitude Response for 0.5 dB Bandwidths Programmed from 2 MHz to 29 MHz in 1 MHz Steps 09422-043 1MHz TO 31MHz PROG. 25dB FILTERS VGA PROGRAMMABLE FILTERS RELATIVE MAGNITUDE (Hz) 3dB/6dB PREAMP The input buffers in both channels can be configured simultaneously for a gain of 3 dB or 6 dB through the SPI (see the Register Map and Codes section). When configured for a 3 dB gain, the buffers support a 400 mV p-p differential input level with ~70 dBc harmonic distortion. For a 6 dB gain setting, the buffers support 280 mV p-p inputs. Data Sheet ADRF6516 500 0.3 50 15mV/dB 400 40 0.2 30 0.1 20 0 100 10 -0.1 0 0 -0.2 200 14x -100 100k 1M 10M 100M FREQUENCY (Hz) Figure 46. Sixth-Order Butterworth Group Delay Response for 0.5 dB Bandwidths Programmed to 2 MHz and 28 MHz -10 0 -0.3 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 2.25 2.50 2.75 3.00 VGAIN (V) 09422-049 GAIN (dB) 300 GAIN ERROR (dB) BW = 28MHz 09422-044 GROUP DELAY (ns) BW = 2MHz Figure 47. Linear-in-dB Gain Control Response of the X-AMP VGA Cascade Showing Consistent Slope and Low Error The corner frequency of the filters is defined by RC products, which can vary by 30% in a typical process. Therefore, all the parts are factory calibrated for corner frequency, resulting in a residual 15% corner frequency variation over the -40C to +85C temperature range. Although absolute accuracy requires calibration, the matching of RC products between the pair of channels is better than 1% by observing careful design and layout practices. Calibration and excellent matching ensure that the magnitude and group delay responses of both channels track together, a critical requirement for digital IQ-based communication systems. VARIABLE GAIN AMPLIFIERS (VGAs) The cascaded VGAs are based on the Analog Devices, Inc., patented X-AMP(R) architecture, consisting of tapped 25 dB attenuators followed by programmable gain amplifiers. The X-AMP architecture generates a continuous linear-in-dB monotonic gain response with low ripple. The analog gains of both cascaded VGA sections are controlled through the high impedance GAIN pin with an accurate slope of 15 mV/dB. The gain response shown in Figure 47 shows the GAIN pin voltage range and the absence of gain foldback at high VGAIN. By changing the gains of both VGAs simultaneously, a more gradual variation in noise and distortion is achieved. The fixed gain following each of the variable gain sections can also be programmed to two different values to maximize dynamic range. OUTPUT BUFFERS/ADC DRIVERS The low impedance (30 ) output buffers of the ADRF6516 are designed to drive either ADC inputs or subsequent amplifier stages. They are capable of delivering up to 1.5 V p-p composite two-tone signals into 1 k differential loads with >65 dBc IMD3. The output common-mode voltage defaults to VPS/2, but it can be adjusted from 700 mV to 2.8 V without loss of drive capability by presenting the VOCM pin with the desired common-mode voltage. The high input impedance of VOCM allows the ADC reference output to be connected directly. Even though the output common-mode voltage is adjustable and the offset compensation loop can null the accumulated dc offsets (see the DC Offset Compensation Loop section), it may still be desirable to ac couple the outputs by selecting the coupling capacitors according to the load impedance and desired bandwidth. DC OFFSET COMPENSATION LOOP In many signal processing applications, no information is carried in the dc level. In fact, dc voltages and other low frequency disturbances can often dominate the intended signal and consume precious dynamic range in the analog path and bits in the data converters. These dc voltages can be present with the desired input signal or can be generated inside the signal path by inherent dc offsets or other unintended signaldependent processes such as self-mixing or rectification. Because the ADRF6516 is fully dc-coupled, it may be necessary to remove these offsets to realize the maximum signal-to-noise ratio (SNR). This can be achieved with ac coupling capacitors at the input and output pins; however, large value capacitors with low impedance values are required because the high-pass corners must be <10 Hz. To address the issue of dc offsets, the ADRF6516 provides an offset compensation loop that nulls the output differential dc level, as shown in Figure 48. If the compensation loop is not required, it can be disabled by pulling the OFDS pin high. Rev. C | Page 17 of 29 ADRF6516 Data Sheet NOISE CHARACTERISTICS OFSx The output noise behavior of the ADRF6516 depends on the gain and bandwidth settings. Figure 49 and Figure 50 show the total output noise spectral density vs. frequency for different bandwidth settings and VGA gains. BASEBAND OUTPUTS The offset compensation loop creates a high-pass corner, fHP, that is superimposed on the normal Butterworth filter response. Typically, fHP is many orders of magnitude lower than the lowest programmed filter bandwidth so that there is no interaction between them. Setting fHP is accomplished with capacitors, COFS, from the OFS1 and OFS2 pins to ground. Because the compensation loop works around the VGA sections, fHP is also dependent on the total gain of the cascaded VGAs. In general, the expression for fHP is given by fHP (Hz) = 6.7 x (Post Filter Linear Gain/COFS (F)) where Post Filter Linear Gain is expressed in linear terms, not in decibels (dB), and is the gain following the filters, which excludes the preamplifier gain of 1.4 (3 dB) or 2 (6 dB). Note that fHP increases in proportion to the gain. For this reason, COFS must be chosen at the highest operating gain to guarantee that fHP is always below the maximum limit required by the system. PROGRAMMING THE FILTERS AND GAINS The 0.5 dB corner frequencies for both filters and the gains of the preamplifiers and postamplifiers are programmed simultaneously through the SPI port. An 8-bit register stores the 5-bit code for corner frequencies of 1 MHz through 31 MHz, as well as the 1-bit codes for the preamplifier gain, the VGA maximum gain, and the postamplifier gain (see Table 4). The SPI protocol not only allows frequency and gain codes to be written to the DATA pin, but it also allows the stored code to be read back via the SDO pin. The latch enable (LE) pin must first go to a Logic 0 for a read or write cycle to begin. On the next rising edge of the clock (CLK), a Logic 1 on the DATA pin initiates a write cycle, whereas a Logic 0 on the DATA pin initiates a read cycle. In a write cycle, the next eight CLK rising edges latch the desired 8-bit code, LSB first. When LE goes high, the write cycle is completed and the frequency and gain codes are presented to the filter and amplifiers. In a read cycle, the next eight CLK falling edges present the stored 8-bit code, LSB first. When LE goes high, the read cycle is completed. Detailed timing diagrams are shown in Figure 2 and Figure 3. GAIN = 40dB -120 -125 -130 GAIN = 20dB -135 -140 GAIN = 0dB -145 -150 5 15 25 35 45 55 65 75 85 95 FREQUENCY (MHz) 09422-051 GAIN Figure 48. Offset Compensation Loop Operates Around the VGA and Output Buffer BANDWIDTH = 31MHz DIGITAL GAIN = 111 -115 Figure 49. Total Output Noise Density with a 31 MHz Corner Frequency for Three Different Gain Settings -100 GAIN = 40dB -105 BANDWIDTH = 1MHz DIGITAL GAIN = 111 -110 -115 -120 -125 GAIN = 20dB -130 -135 -140 GAIN = 0dB -145 -150 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 FREQUENCY (MHz) 09422-052 OUTPUT ADC DRIVER OUTPUT NOISE DENSITY (dBV/Hz) 50dB VGA -110 09422-050 FROM FILTERS OUTPUT NOISE DENSITY (dBV/Hz) COFS OFDS Figure 50. Total Output Noise Density with a 1 MHz Corner Frequency for Three Different Gain Settings Both the filter sections and the VGAs contribute to the total noise at the output. The filter contributes a noise spectral density profile that is flat at low frequencies, peaks near the corner frequency, and then rolls off as the filter poles roll off the gain and noise. The magnitude of the noise spectral density contributed by the filter, expressed in nV/Hz, varies inversely with the square root of the bandwidth setting, resulting in a total integrated noise in nV that is nearly constant with bandwidth setting. At higher frequencies, after the filter noise rolls off, the noise floor is set by the VGAs. Each of the X-AMP VGA sections used in the ADRF6516 contributes a fixed and flat noise spectral density to its respective output, independent of the gain setting. Because the VGAs are cascaded in the ADRF6516, the total noise contributed by the VGAs at the output increases gradually with higher gain. This is apparent in the noise floor variation at high frequencies at different VGA gain settings. Rev. C | Page 18 of 29 Data Sheet ADRF6516 The exact relationship depends on the programmed fixed gain of the amplifiers. At minimum gain, only the last VGA contributes to the -144 dBV/Hz minimum noise floor, which is equivalent to 63 nV/Hz. At lower frequencies within the filter bandwidth setting, the VGAs translate the filter noise directly to the output by a factor equal to the gain following the filter. At low values of VGA gain, the noise at the output is the flat spectral density contributed by the last VGA. As the gain increases, more noise from the filter and first VGA appears at the output. Because the intrinsic filter noise density increases at lower bandwidth settings, it is more pronounced than it is at higher bandwidth settings. In either case, the noise density asymptotically approaches the limit set by the VGAs at the highest frequencies. For other values of VGA gain and bandwidth setting, the detailed shape of the noise spectral density changes according to the relative contributions of the filters and VGAs. Because the noise spectral density outside the filter bandwidth is limited by the VGA output noise, it may be necessary to use an external, fixed-frequency, passive filter prior to analog-todigital conversion to prevent noise aliasing from degrading the signal-to-noise ratio. A higher sampling rate relative to the maximum required ADRF6516 corner frequency setting reduces the order and complexity of this external filter. DISTORTION CHARACTERISTICS The distortion performance of the ADRF6516 is similar to its noise performance. The filters and the VGAs contribute to the overall distortion and signal handling capabilities. Furthermore, the front end must also cope with out-of-band signals that can be larger than the in-band signals. These out-of-band signals are filtered before reaching the VGA. It is important to understand the signals presented to the ADRF6516 and to match these signals with the input and output characteristics of the part. When the gain is low, the distortion is typically limited by the input section because the output is not driven to its maximum capacity. When the gain is high, the distortion is likely limited by the output section because the input is not driven to its maximum capacity. An exception to this is when the input is driven with a small desired signal in combination with a large out-of-band signal. In this case, the out-of-band signal may drive the input to distort. As long as the input is not overdriven, the out-of-band signal is removed by the filter. A high VGA gain is still needed to raise the small desired signal to a higher level at the output. The overall distortion introduced by the part depends on the input drive level, including the out-of-band signals, and the desired output signal level. As noted in the Input Buffers section, the input section can handle a total signal level of 400 mV p-p for a 3 dB preamplifier gain and 280 mV p-p for a 6 dB preamplifier gain with >70 dBc harmonic distortion. This includes both in-band and out-of-band signals. To distinguish and quantify the distortion performance of the input section, two different IP3 specifications are presented. The first is called in-band IP3 and refers to a two-tone test where the signals are inside the filter bandwidth. This is exactly the same figure of merit familiar to communications engineers in which the third-order intermodulation level, IMD3, is measured. To quantify the effect of out-of-band signals, a new out-of-band (OOB) IIP3 figure of merit is introduced. This test also involves a two-tone stimulus; however, the two tones are placed out-ofband so that the lower IMD3 product lands in the middle of the filter pass band. At the output, only the IMD3 product is visible because the original two tones are filtered out. To calculate the OOB IIP3 at the input, the IMD3 level is referred to the input by the overall gain. The OOB IIP3 allows the user to predict the impact of out-of-band blockers or interferers at an arbitrary signal level on the in-band performance. The ratio of the desired input signal level to the input-referred IMD3 at a given blocker level represents a signal-to-distortion limit imposed by the outof-band signals. MAXIMIZING THE DYNAMIC RANGE The role of the ADRF6516 is to increase the level of a variable in-band signal while minimizing out-of-band signals. Ideally, this is achieved without degrading the SNR of the incoming signal or introducing distortion to the incoming signal. The first goal is to maximize the output signal swing, which can be defined by the ADC input range or the input signal capacity of the next analog stage. For the complex waveforms often encountered in communication systems, the peak-to-average ratio, or crest factor, must be considered when selecting the peak-to-peak output. From the selected output signal and the maximum gain of the ADRF6516, the minimum input level can be defined. Lower signal levels do not yield the maximum output and suffer a greater degradation in SNR. As the input signal level increases, the VGA gain is reduced from its maximum gain point to maintain the desired fixed output level. The output noise, initially dominated by the filter, follows the gain reduction, yielding a progressively better SNR. At some point, the VGA gain drops sufficiently that the VGA noise becomes dominant, resulting in a slower reduction in SNR from that point. From the perspective of SNR alone, the maximum input level is reached when the VGA reaches its minimum gain. Rev. C | Page 19 of 29 ADRF6516 Data Sheet Distortion must also be considered when maximizing the dynamic range. At low and moderate signal levels, the output distortion is constant and assumed to be adequate for the selected output level. At some point, the input signal becomes large enough that distortion at the input limits the system. The maximum tolerable input signal depends on whether the input distortion becomes unacceptably large or the minimum gain is reached. The most challenging scenario in terms of dynamic range is the presence of a large out-of-band blocker accompanying a weaker in-band desired signal. In this case, the maximum input level is dictated by the blocker and its inclination to cause distortion. After filtering, the weak desired signal must be amplified to the desired output level, possibly requiring maximum gain. Both the distortion limits associated with the blocker at the input and the SNR limits created by the weaker signal and higher gains are present simultaneously. Furthermore, not only does the blocker scenario degrade the dynamic range, it also reduces the range of input signals that can be handled because a larger part of the gain range is used to simply extract the weak desired signal from the stronger blocker. KEY PARAMETERS FOR QUADRATURE-BASED RECEIVERS The majority of digital communication receivers makes use of quadrature signaling, in which bits of information are encoded onto pairs of baseband signals that then modulate in-phase (I) and quadrature (Q) sinusoidal carriers. Both the baseband and modulated signals appear quite complex in the time domain with dramatic peaks and valleys. In a typical receiver, the goal is to recover the pair of quadrature baseband signals in the presence of noise and interfering signals after quadrature demodulation. In the process of filtering out-of-band noise and undesired interferers and restoring the levels of the desired I and Q baseband signals, it is critical to retain their gain and phase integrity over the bandwidth. The ADRF6516 delivers flat in-band gain and group delay, consistent with a six-pole Butterworth prototype filter, as described in the Programmable Filters section. Furthermore, careful design ensures excellent matching of these parameters between the I and Q channels. Although absolute gain flatness and group delay can be corrected with digital equalization, mismatch introduces quadrature errors and intersymbol interference that degrade bit error rates in digital communication systems. Rev. C | Page 20 of 29 Data Sheet ADRF6516 APPLICATIONS INFORMATION BASIC CONNECTIONS For example, the high impedance VOCM input pin of the ADRF6806 quadrature demodulator can be directly connected to the VICM pin of the ADRF6516. This gives the ADRF6806 the optimal common-mode voltage reference to drive the ADRF6516. Figure 51 shows the basic connections for a typical ADRF6516 application. SUPPLY DECOUPLING A nominal supply voltage of 3.3 V must be applied to the supply pins. The supply voltage must not exceed 3.45 V or drop below 3.15 V. Each supply pin must be decoupled to ground with at least one low inductance, surface-mount ceramic capacitor of 0.1 F placed as close as possible to the ADRF6516 device. OUTPUT SIGNAL PATH The low impedance (30 ) output buffers are designed to drive a high impedance load, such as an ADC input or another amplifier stage. The output pins--OPP1, OPM1, OPP2, and OPM2--sit at a nominal output common-mode voltage of VPS/2, but can be driven to a voltage of 0.7 V to 2.8 V by applying the desired common-mode voltage to the high impedance VOCM pin. The ADRF6516 has two separate supplies: an analog supply and a digital supply. Take care to separate the analog and digital supplies with a large surface-mount inductor of 33 H. Decouple each supply separately to its respective ground through a 10 F capacitor. DC OFFSET COMPENSATION LOOP ENABLED When the dc offset compensation loop is enabled via the OFDS pin, the ADRF6516 can null the output differential dc level. The loop is enabled by pulling the OFDS pin low to ground. The offset compensation loop creates a high-pass corner frequency, which is proportional to the value of the capacitors that are connected from the OFS1 and OFS2 pins to ground. For more information about setting the high-pass corner frequency, see the DC Offset Compensation Loop section. INPUT SIGNAL PATH Each signal path has input buffers, accessed through the INP1, INM1, INP2, and INM2 pins, that set a differential input impedance of 1600 . These inputs sit at a nominal commonmode voltage around midsupply. The inputs can be dc-coupled or ac-coupled. If using direct dc coupling, the common-mode voltage, VCM, can range from 1.1 V to 1.8 V. The VICM pin can be used as a reference commonmode voltage for driving a high impedance sensing node of the preceding cascaded part (VICM has a 7 k impedance). COMMON-MODE BYPASSING The ADRF6516 common-mode pins, VICM and VOCM, must be decoupled to ground. Use at least one low inductance, surface-mount ceramic capacitor with a value of 0.1 F to decouple the common-mode pins. INPUT1 (-) 0.1F VPS 0.1F INPUT1 (+) VPS VPS OUTPUT1 (+) 0.1F VPSD 0.1F ENBL INM1 COM OFS1 INP1 VICM VPS VPS OPP1 VPSD OPM1 COMD COM LE SERIAL CONTROL INTERFACE CLK ADRF6516 VOCM DATA 0.1F VPS OUTPUT1 (-) GAIN SDO COM COM OPM2 0.1F 0.1F OUTPUT2 (-) OPP2 VPS OFDS VPS INP2 OFS2 COM INM2 COM VPS VPS 0.1F INPUT2 (+) INPUT2 (-) VPS VPS 0.1F Figure 51. Basic Connections Rev. C | Page 21 of 29 09422-053 OUTPUT2 (+) ADRF6516 Data Sheet SERIAL PORT CONNECTIONS EFFECT OF FILTER BANDWIDTH ON EVM The ADRF6516 has a SPI port to control the gain and filter bandwidth settings. Data can be written to the internal 8-bit register and read from the register. It is recommended that low-pass RC filtering be placed on the SPI lines to filter out any high frequency glitches. See Figure 58, the evaluation board schematic, for an example of a low-pass RC filter. Take care when when selecting the filter bandwidth. In a digital transceiver, the modulated signal is filtered by a pulse shaping filter (such as a root-raised cosine filter) at both the transmit and receive ends to guard against intersymbol interference (ISI). If additional filtering of the modulated signal is done, the signal must be within the pass band of the filter. When the corner frequency of the ADRF6516 filter begins to encroach on the modulated signal, ISI is introduced and degrades EVM, which can lead to loss of signal lock. Error vector magnitude (EVM) is a measure used to quantify the performance of a digital radio transmitter or receiver by measuring the fidelity of the digital signal transmitted or received. Various imperfections in the link, such as magnitude and phase imbalance, noise, and distortion, cause the constellation points to deviate from their ideal locations. In general, a receiver exhibits three distinct EVM limitations vs. received input signal power. As signal power increases, the distortion components increase. * * At large enough signal levels, where the distortion components due to the harmonic nonlinearities in the device are falling in-band, EVM degrades as signal levels increase. At medium signal levels, where the signal chain behaves in a linear manner and the signal is well above any notable noise contributions, EVM has a tendency to reach an optimal level determined dominantly by either the quadrature accuracy and IQ gain match of the signal chain or the precision of the test equipment. As signal levels decrease, such that noise is a major contributor, EVM performance vs. the signal level exhibits a decibel-for-decibel degradation with decreasing signal level. At these lower signal levels, where noise is the dominant limitation, decibel EVM is directly proportional to the SNR. -5 0.7 30MHz 15MHz 10MHz 9MHz 8MHz GAIN VOLTAGE -10 -15 0.6 0.5 -20 0.4 -25 -30 0.3 -35 0.2 -40 0.1 -45 0 -50 -25 -20 -15 -10 -5 RF INPUT POWER (dBm) 0 5 Figure 52. EVM vs. RF Input Power at Several Filter Corner Settings (256-QAM, 14 MSPS Signal with = 0.35; Output Differential Signal Level Held to 700 mV p-p; OFDS Pulled High) Figure 53 shows the degradation that a fixed filter corner has on EVM as the signal bandwidth corner is increased in fine increments until loss of signal lock occurs. 0 -5 EVM TEST SETUP -10 The basic setup to test EVM for the ADRF6516 consisted of an Agilent E4438C used as a signal source and a Hewlett-Packard 89410A vector signal analyzer (VSA) used to sample and calculate the EVM of the signal. The E4438C IQ baseband differential outputs drove the ADRF6516 inputs. The I and Q outputs of the ADRF6516 were loaded with 1 k differential impedances and connected differentially to two AD8130 differential amplifiers to convert the signals into single-ended signals. The single-ended signals were connected to the input channels of the VSA. -15 EVM (dB) FILTER BANDWIDTH CORNER -20 -25 -30 -35 -40 -45 -50 3 4 8 6 7 5 SIGNAL BANDWIDTH CORNER (MHz) 9 10 09422-055 * 0.8 0 GAIN VOLTAGE (V) ERROR VECTOR MAGNITUDE (EVM) PERFORMANCE Figure 52 shows that a digitally modulated QAM baseband signal with a bandwidth at 9.45 MHz has excellent EVM even at a filter corner frequency of 8 MHz. Further reduction in the corner frequency leads to complete loss of lock. As RF input power was swept, the ADRF6516 attained an EVM of less than -45 dB over an input power range of approximately 20 dB. 09422-054 To enable the ADRF6516, the ENBL pin must be pulled high. Driving the ENBL pin low disables the device, reducing current consumption to approximately 9 mA at room temperature. EVM (dB) ENABLE/DISABLE FUNCTION Figure 53. EVM vs. Signal Bandwidth Corner at a Filter Corner of 5 MHz and a 16-QAM Signal with = 0.35 Rev. C | Page 22 of 29 Data Sheet ADRF6516 Output voltage level can affect EVM greatly when the signal is compressed. When changing the output voltage levels of the ADRF6516, take care that the output signal is not in compression, which causes EVM degradation. Figure 54 show EVM performance vs. RF input power for several maximum differential I and Q output voltage levels of 350 mV p-p up to 2.4 V p-p. For the lower maximum differential output voltage levels, the EVM is less than -45 dB over approximately 20 dB of input power range. Figure 55 shows degradation of the EVM vs. RF input power as the COFS capacitor value becomes smaller, which increases the high-pass corner for the dc offset compensation loop. 0 -5 -10 -15 EVM (dB) EFFECT OF OUTPUT VOLTAGE LEVELS ON EVM -20 -25 COFS = 1F COFS = 220nF COFS = 1nF -30 0 -35 -5 -40 -10 -45 350mV p-p MAX 700mV p-p MAX 1500mV p-p MAX 2400mV p-p MAX -30 -40 -5 -15 -10 RF INPUT POWER (dBm) 0 5 09422-056 -45 -20 -20 -15 -10 -5 RF INPUT POWER (dBm) 0 5 Figure 55. EVM vs. RF Input Power at Several COFS Values (Filter Corner = 10 MHz, 256-QAM, 14 MSPS Signal with = 0.35; Output Differential Signal Level Held to 700 mV p-p; OFDS Pulled Low) -35 -50 -25 -25 Figure 54. EVM vs. RF Input Power at Several Output Maximum Differential Voltage Levels (Filter Corner = 10 MHz, OFDS Pulled High) For the largest tested maximum differential output voltage level of 2.4 V p-p, the ADRF6516 begins to compress the signal. This compression causes EVM to degrade, but it still remains below -40 dB, albeit over a truncated input power range. At the high end of the input power range, the signal is in full compression and EVM is large. Given that the gain is near its minimum, the input signal level must be lowered to bring the output signal out of full compression and into the proper linear operating region. EFFECT OF COFS VALUE ON EVM Figure 56 shows the effect that COFS has on several modulated signal bandwidths. The modulated bandwidth was swept while using 1000 pF and 1 F values for COFS. Total gain was set to 15 dB, so the high-pass filter corner of the 1000 pF capacitor is 26.67 kHz, and the high-pass filter corner of the 1 F capacitor is 26.67 Hz. It is recommended that at moderate signal bandwidths, a 1 F capacitor for COFS be used to obtain the best EVM when using the dc offset compensation loop. 0 -5 -10 -15 When enabled, the dc offset compensation loop effectively nulls any information below the high-pass corner set by the COFS capacitor. However, loss of the low frequency information of the modulated signal can degrade the EVM in some cases. As the signal bandwidth becomes larger, the percentage of information that is corrupted by the high-pass corner becomes smaller. In such cases, it is important to select a COFS capacitor that is large enough to minimize the high-pass corner frequency, which prevents loss of information and degraded EVM. Rev. C | Page 23 of 29 -20 -25 -30 COFS = 1000pF -35 -40 COFS = 1F -45 -50 0 1 2 3 4 5 6 7 8 SIGNAL BANDWIDTH CORNER (MHz) 9 10 Figure 56. EVM vs. Signal Bandwidth Corner with COFS = 1 F and COFS = 1000 pF (Filter Corner = 10 MHz) 09422-058 -25 -30 09422-057 -50 -35 -20 EVM (dB) EVM (dB) -15 ADRF6516 Data Sheet EVALUATION BOARD An evaluation board is available for testing the ADRF6516. The evaluation board schematic is shown in Figure 58. Table 6 provides the component values and suggestions for modifying the component values for the various modes of operation. EVALUATION BOARD CONTROL SOFTWARE The ADRF6516 evaluation board is controlled through the parallel port on a PC. The parallel port is programmed via the ADRF6516 evaluation software. This software controls the filter corner frequency, as well as the minimum and maximum gains for each amplifier in the ADRF6516. For information about the register map, see Table 4 and Table 5. For information about SPI port timing and control, see Figure 2 and Figure 3. After the evaluation software is downloaded and installed, start the basic user interface to program the filter corner and gain values (see Figure 57). When the user clicks the Write Bits button, a write operation is executed, immediately followed by a read operation. The updated information is displayed in the Current Pre-Amp Gain, Current Frequency, Current VGA Max Gain, and Current Post-Amp Gain fields. When the parallel port is updated with a read/write operation, the current cumulative maximum gain of all the amplifiers is displayed in the Maximum Gain field. (The analog VGA gain is not included in this value.) Because the speed of the parallel port varies from PC to PC, the Clock Stretch function can be used to change the effective frequency of the CLK line. The CLK line has a scalar range from 1 to 10; 10 is the fastest speed, and 1 is the slowest. To program the filter corner, do one of the following: Click the arrow in the Frequency Select section of the window, select the desired corner frequency from the menu, and click Write Bits. Click Freq +1 MHz or Freq -1 MHz to increment or decrement the corner frequency in 1 MHz steps from the current corner frequency. To program the preamplifier gain, the VGA maximum gain, and the postamplifier gain, move the slider switch in the appropriate section of the window to the desired gain. The preamplifier gain can be set to 3 dB or 6 dB. The VGA maximum gain can be set to 22 dB or 28 dB. The postamplifier gain can be set to 6 dB or 12 dB. 09422-060 Figure 57. ADRF6516 Evaluation Software Rev. C | Page 24 of 29 Data Sheet ADRF6516 SCHEMATICS AND ARTWORK VPOSD VPOS R45 OPEN R31 0 L2 33H R47 0 1 6 R55 OPEN R57 C9 0 100nF 2 T1 4 R56 OPEN C6 0.1F R48 0 3 INP1 R43 OPEN R58 C10 0 100nF C30 330pF R30 100 VPSD C4 0.1F DATA C5 0.1F R34 SDO 0 R1 10k VPS R49 0 R32 0 R37 OPEN ENBL INM1 COM OFS1 INP1 VICM VPS VPS OPP1 VPSD OPM1 COMD COM LE ADRF6516 GAIN C19 100nF 6 1 COM COM OPM2 C21 R6 C18 0.1F 100nF 0 OPP2 VPS OFDS VPS INP2 OFS2 COM INM2 COM VPS INM2_SE_P R44 OPEN C7 100nF 3 C3 0.1F R50 0 R52 OPEN R54 0 C8 100nF R12 OPEN R19 0 C11 0.1F C13 1000pF R41 0 T3 C22 100nF C15 0.1F VOCM VOCM R9 0 R10 0 OPM1_SE_P R39 OPEN VOCM SDO R14 R35 OPEN 0 R13 OPEN R38 OPEN R42 0 OPM2_SE_P T4 C24 0.1F R36 0 OPP2 R40 OPEN 2 T2 4 R53 0 R7 0 OPP1 R11 VGAIN R8 C23 OPEN 0.1F 0 R20 C17 C20 R5 0 VGAIN 0.1F 100nF 0 VPS R51 OPEN COM L1 33H VPS R46 OPEN INP2 C2 10F C14 1000pF DATA 0 VPOS C1 10F COMD C16 0.1F CLK R33 VICM C12 0.1F P2 C29 330pF DIG_VPOS C27 0.1F VPS R29 100 LE CLK VPS R3 10k VPS P4 VPS Figure 58. Evaluation Board Schematic Rev. C | Page 25 of 29 09422-061 INM1_SE_P ADRF6516 Data Sheet Y1 24MHz 3V3_USB 3 1 C54 22pF C51 22pF 4 2 R62 100k 3V3_USB R64 0 1 C48 10pF 50 49 48 47 46 PD6_FD14 PD5_FD13 PD4_FD12 PD3_FD11 PD2_FD10 PD1_FD9 RDY0_SLRD 45 44 43 VCC 51 PD0_FD8 52 WAKEUP 53 GND 54 PD7_FD15 55 VCC GND 56 CLKOUT C45 0.1F RESET_N 42 2 RDY1_SLWR GND 41 3 AVCC 5V_USB PA7_FLAGD_SCLS_N 40 PA6_PKTEND 39 4 XTALOUT 5 C49 0.1F P5 1 2 3 4 5 G1 G2 G3 G4 C37 0.1F PA5_FIFOARD1 38 XTALIN 6 AGND PA4_FIFOARD0 37 3V3_USB 7 CY7C68013A-56LTXC AVCC 3V3_USB LE PA3_WU2 36 U4 8 DPLUS PA2_SLOE 35 CLK 9 DMINUS PA1_INT1_N 34 DATA 10 AGND PA0_INT0_N 33 SDO 11 VCC VCC 32 12 GND CTL2_FLAGC 31 13 IFCLK 3V3_USB CTL1_FLAGB 30 PB7_FD7 GND VCC GND 19 PB6_FD6 18 PB5_FD5 17 PB4_FD4 PB0_FD0 PB1_FD1 16 PB3_FD3 VCC 15 R61 2k CTL0_FLAGA 29 PB2_FD2 SCL SDA 14 RESERVED 20 21 22 23 24 25 26 27 28 CR2 3V3_USB R59 2k 24LC64-I_SN U2 C39 0.1F 3V3_USB C38 10pF 5V_USB ADP3334 3V3_USB 1 A0 SDA 5 R60 2k 2 A1 SCL 6 3V3_USB 3 4 A2 WC_N GND VCC U3 C52 1.0F 7 8 R70 140k 3V3_USB C50 1000pF R69 78.7k 1 OUT1 IN2 2 OUT2 IN1 7 3 FB SD 6 4 NC GND 5 8 C47 1.0F R65 2k CR1 DGND 3V3_USB C41 0.1F C42 0.1F C35 0.1F C36 0.1F C44 0.1F C46 0.1F 09422-159 C40 0.1F Figure 59. USB Evaluation Board Schematic Rev. C | Page 26 of 29 ADRF6516 09422-062 09422-063 Data Sheet Figure 61. Component Side Layout Figure 60. Top Layer Silkscreen Table 6. Evaluation Board Configuration Options Components C1, C2, C4, C5, C11, C12, C15, C16, L1, L2, R2 Function Power supply and ground decoupling. Nominal supply decoupling consists of a 0.1 F capacitor to ground. T1, T2, C3, C6, C7 to C10, R31, R32, R43 to R58 Input interface. Input SMAs INP1, INM1_SE_P, INP2_SE_P, and INM2 are used to drive the part differentially by bypassing the baluns. Using only INM1_SE_P and INP2_SE_P in conjunction with the baluns enables single-ended operation. The default configuration of the evaluation board is for single-ended operation. T1 and T2 are 8:1 impedance ratio baluns that transform a singleended signal in a 50 system into a balanced differential signal in a 400 system. R31, R32, R47, R48, R49, and R50 are populated for appropriate balun interface. R51 to R58 are provided for generic placement of matching components. To bypass the T1 and T2 baluns for differential interfacing, remove the balun interfacing resistors R31, R32, R47, R48, R49, and R50, and populate R43, R44, R45, and R46 with 0 resistors. Output interface. Output SMAs OPP1_SE_P, OPM1, OPP2, and OPM2_SE_P are used to obtain differential signals from the part when the output baluns are bypassed. Using OPP1_SE_P, OPM2_SE_P, and the baluns, the user can obtain single-ended output signals. The default configuration of the evaluation board is for single-ended operation. T3 and T4 are 8:1 impedance ratio baluns that transform a differential signal in a 400 system into a single-ended signal in a 50 system. R7, R8, R9, R10, R19, R20, R35, R36, R41, and R42 are populated for appropriate balun interface. R7 to R14 are provided for generic placement of matching components. To bypass the T3 and T4 baluns for differential interfacing, remove the balun interfacing resistors R19, R20, R35, R36, R41, and R42, and populate R37, R38, R39, and R40 with 0 resistors. T3, T4, C19 to C24, R7 to R14, R19, R20, R35 to R42 Rev. C | Page 27 of 29 Default Conditions C1, C2 = 10 F (Size 1210) C4, C5, C11, C12, C15, C16 = 0.1 F (Size 0402) L1, L2 = 33 H (Size 1812) R2 = 1 k (Size 0402) T1, T2 = ADT8-1T+ (Mini-Circuits) C3, C6 = 0.1 F (Size 0402) C7 to C10 = 100 nF (Size 0602) R31, R32, R47 to R50, R53, R54, R57, R58 = 0 (Size 0402) R43 to R46, R51, R52, R55, R56 = open (Size 0402) T3, T4 = ADT8-1T+ (Mini-Circuits) C19 to C22 = 100 nF (Size 0402) C23, C24 = 0.1 F (Size 0402) R7 to R10, R19, R20, R35, R36, R41, R42 = 0 (Size 0402) R11 to R14, R37 to R40 = open (Size 0402) ADRF6516 Components P2 P1, C28, C29, R1, R29, R30, R33, R34 P4, C13, C14, R3 C27 C18, R6 C17, R5 U2, U3, U4, P5 Data Sheet Function Enable interface. The ADRF6516 is powered up by applying a logic high voltage to the ENBL pin (Jumper P2 is connected to VPS). Serial control interface. The digital interface sets the corner frequency, the preamplifier gain, the postamplifier gain, and the VGA maximum gain of the device using the serial interface via the LE, CLK, DATA, and SDO pins. RC filter networks are provided on the CLK and LE lines to filter the PC signals. CLK, DATA, and LE signals can be observed via SMB connectors for debug purposes. DC offset compensation loop. The dc offset compensation loop is enabled (low) with Jumper P4. When enabled, the C13 and C14 capacitors are connected to circuit common. The high-pass corner frequency is expressed as follows: fHP (Hz) = 6.7 x (Post Filter Linear Gain/COFS (F)) Input common-mode setpoint. The input common-mode voltage can be set externally when applied to the VICM pin. If the VICM pin is left open, the input common-mode voltage defaults to VPS/2. Output common-mode setpoint. The output common-mode voltage can be set externally when applied to the VOCM pin. If the VOCM pin is left open, the output common-mode voltage defaults to VPS/2. Analog gain control. The range of the GAIN pin is from 0 V to 1 V, creating a gain scaling of 15 mV/dB. Cypress Microcontroller, EEPROM, and LDO C35, C36, C40, C41, C42, C44, C46 C48, C49, C45, C56, C57, C58, R59, R60, R61, R62, R64, CR2 3.3 V supply decoupling. Several capacitors are used for decoupling on the 3.3 V supply. Cypress and EEPROM components. C47, C50, C52, R65, R69, R70, CR1 LDO components Y1, C51, C54 Crystal oscillator and components. 24 MHz crystal oscillator. Rev. C | Page 28 of 29 Default Conditions P2 = installed for enable P1 = installed R1 = 10 k (Size 0402) C28, C29 = 330 pF (Size 0402) R29, R30 = 100 (Size 0402) R33, R34 = 0 (Size 0402) P4 = installed C13, C14 = 1000 pF (Size 0402) R3 = 10 k (Size 0402) C27 = 0.1 F (Size 0402) C18 = 0.1 F (Size 0402) R6 = 0 (Size 0402) C17 = 0.1 F (Size 0402) R5 = 0 (Size 0402) U2 = Microchip MICRO24LC64 U3 = Analog Devices ADP3334ACPZ U4 = Cypress Semiconductor CY7C68013A-56LTXC P5 = Mini USB connector C35, C36, C40, C41, C42, C44, C46 = 0.1 F (0402) C57, C48 = 10 pF (0402) C56, C58, C45, C49 = 0.1 F (0402) R59, R60, R61 = 2 k (0402) R62, R64 = 100 k (0402) CR2 = ROHM SML-21OMTT86 C47, C52 = 1 F (0402) C50 = 1000 pF (0402) R65 = 2 k (0402) R69 = 78.7 k (0402) R70 = 140 k (0402) CR1 = ROHM SML-21OMTT86 Y1 = NDK NX3225SA-24MHz C51, C54 = 22 pF (0402) Data Sheet ADRF6516 OUTLINE DIMENSIONS DETAIL A (JEDEC 95) 0.30 0.25 0.18 25 PIN 1 INDIC ATOR AREA OPTIONS (SEE DETAIL A) 32 24 1 0.50 BSC 3.25 3.10 SQ 2.95 EXPOSED PAD 17 TOP VIEW 0.80 0.75 0.70 SIDE VIEW PKG-003898 SEATING PLANE 0.50 0.40 0.30 8 9 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF BOTTOM VIEW 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD 02-22-2017-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 Figure 62. 32-Lead Lead Frame Chip Scale Package [LFCSP] 5 mm x 5 mm Body and 0.75 mm Package Height (CP-32-7) Dimensions shown in millimeters ORDERING GUIDE Model1 ADRF6516ACPZ-R7 ADRF6516-EVALZ 1 Temperature Range -40C to +85C Package Description 32-Lead LFCSP, 7" Tape and Reel Evaluation Board Z = RoHS Compliant Part. (c)2010-2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09422-0-8/17(C) Rev. C | Page 29 of 29 Package Option CP-32-7