WT32
DATA SHEET
Monday, 09 September 2013
Version 2.19
Bluegiga Technologies Oy
Copyright © 2000-2013 Bluegiga Technologies
All rights reserved.
Bluegiga Technologies assumes no responsibility for any errors which may appear in this manual.
Furthermore, Bluegiga Technologies reserves the right to alter the hardware, software, and/or specifications
detailed here at any time without notice and does not make any commitment to update the information
contained here. Bluegiga’s products are not authorized for use as critical components in life support devices
or systems.
The WRAP, Bluegiga Access Server, Access Point and iWRAP are registered trademarks of Bluegiga
Technologies.
The Bluetooth trademark is owned by the Bluetooth SIG Inc., USA and is licensed to Bluegiga Technologies.
All other trademarks listed herein are owned by their respective owners.
Bluegiga Technologies Oy
VERSION HISTORY
Version
Comment
1.0
Soldering recommendations added. Layout guide fixed. Details at
VREG_ENA. Operating temperature range fixed.
1.1
Bluetooth and FCC qualification IDs added
1.2
Figure 18 fixed. Recommendation for external ESD protection removed.
1.3
Changed VREG_ANA to VREG_ENA
1.4
Radiocharacteristics updated
1.5
List of pretested antennas added
1.51
Table 1 corrected
1.52
PSKEY_PCM_CONFIG32 description corrected
1.53
Table 4: minor correction
1.6
Dimensions updated
1.7
Cross references fixed
1.8
Layout guide for WT32-N added
1.9
Note added regarding WT32-N
2.0
Charger current settings specified, MIC_BIAS description corrected
2.1
Minor updates
2.11
Table 2 corrected
2.12
Physical dimensions, width corrected
2.13
Table 22 updated
2.14
AIO0 and AIO1 in table 8
2.15
MIC Japan certification info
2.16
S/PDIF warning added
2.17
Updated contact information
Bluegiga Technologies Oy
2.18
Added additional note about SPDIF
2.19
Minor changes
Bluegiga Technologies Oy
TABLE OF CONTENTS
1 Ordering Information......................................................................................................................................9
2 Block Diagram and Descriptions ................................................................................................................ 10
3 Electrical Characteristics ............................................................................................................................ 12
3.1 Absolute maximum ratings .................................................................................................................. 12
3.2 Recommended operating conditions .................................................................................................. 12
3.3 Terminal characteristics ...................................................................................................................... 13
3.4 Battery charger .................................................................................................................................... 14
3.5 Radio characteristics and general specifications ................................................................................ 16
3.6 Radio Characteristics .......................................................................................................................... 17
3.6.1 Radiation Pattern (WT32EK) ....................................................................................................... 17
4 WT32 Pin Description ................................................................................................................................. 18
4.1 Device Terminal Functions .................................................................................................................. 19
5 Power Control ............................................................................................................................................. 24
5.1 Power Supply Configuration ................................................................................................................ 24
5.2 Voltage Regulator Enable Pin ............................................................................................................. 24
5.3 Battery Charger ................................................................................................................................... 25
5.4 RESET ................................................................................................................................................ 26
6 Serial Interfaces .......................................................................................................................................... 28
6.1 UART Interface .................................................................................................................................... 28
6.1.1 UART Configuration While RESET is Active ............................................................................... 29
6.1.2 UART Bypass Mode .................................................................................................................... 29
6.2 USB Interface ...................................................................................................................................... 31
6.2.1 USB Pull-Up Resistor ................................................................................................................... 31
6.2.2 Self Powered Mode ...................................................................................................................... 31
6.2.3 Bus Powered Mode ...................................................................................................................... 32
6.2.4 Suspend Current .......................................................................................................................... 32
6.2.5 Detach and Wake-Up Signaling ................................................................................................... 32
6.2.6 USB Driver ................................................................................................................................... 33
6.2.7 USB 1.1 Compliance .................................................................................................................... 33
6.2.8 USB 2.0 Compatibility .................................................................................................................. 33
6.3 SPI Interface ........................................................................................................................................ 34
7 Audio Interfaces .......................................................................................................................................... 35
7.1 Audio Interface .................................................................................................................................... 35
7.1.1 Audio Input and Output ................................................................................................................ 35
7.2 Stereo Audio CODEC Interface .......................................................................................................... 36
7.2.1 ADC .............................................................................................................................................. 37
7.2.2 DAC .............................................................................................................................................. 38
Bluegiga Technologies Oy
7.2.3 IEC 60958 Interface ..................................................................................................................... 39
7.2.4 Microphone Input ......................................................................................................................... 40
7.2.5 Line Input ..................................................................................................................................... 42
7.2.6 Output Stage ................................................................................................................................ 42
7.3 Digital Audio Interface (I2S) ................................................................................................................ 44
7.4 PCM Interface ..................................................................................................................................... 47
7.4.1 PCM Interface Master/Slave ........................................................................................................ 47
7.4.2 Long Frame Sync ......................................................................................................................... 48
7.4.3 Short Frame Sync ........................................................................................................................ 48
7.4.4 Multi Slot Operation ..................................................................................................................... 49
7.4.5 GCI Interface ................................................................................................................................ 49
7.4.6 Slots and Sample Formats ........................................................................................................... 49
7.4.7 Additional Features ...................................................................................................................... 50
7.4.8 PCM CLK and SYNC Generation ................................................................................................ 50
7.4.9 PCM Configuration ....................................................................................................................... 51
8 I/O Parallel Ports ........................................................................................................................................ 52
9 Software Stacks .......................................................................................................................................... 53
9.1 iWRAP Stack ....................................................................................................................................... 53
9.2 VM Stack ............................................................................................................................................. 54
10 Enhanced Data Rate .............................................................................................................................. 56
10.1 Enhanced Data Rate Baseband .................................................................................................. 56
10.2 Enhanced Data Rate ∏/4 DQPSK ............................................................................................... 56
10.3 8DQPSK ....................................................................................................................................... 57
11 Layout and Soldering Considerations ..................................................................................................... 58
11.1 Soldering Recommendations ....................................................................................................... 58
11.2 Layout Guidelines ........................................................................................................................ 58
11.2.1 Audio Layout ................................................................................................................................ 58
11.2.2 Antenna Design ........................................................................................................................... 58
12 WT32 Physical Dimensions .................................................................................................................... 60
13 Package .................................................................................................................................................. 62
14 Certifications ........................................................................................................................................... 64
14.1 Bluetooth ...................................................................................................................................... 64
14.2 FCC .............................................................................................................................................. 65
14.3 CE ................................................................................................................................................ 66
14.4 Industry Canada (IC) .................................................................................................................... 66
14.5 MIC Japan .................................................................................................................................... 67
14.6 Pretested antennas ...................................................................................................................... 68
15 RoHS Statement with a List of Banned Materials ................................................................................... 70
Bluegiga Technologies Oy
16 Contact Information................................................................................................................................. 71
8
WT32 Bluetooth® Audio Module
DESCRIPTION:
WT32 is a Bluetooth 2.1 + EDR module
dedicated for Bluetooth audio applications. In
addition to Bluetooth radio, antenna and
iWRAP Bluetooth stack, WT32 contains a
DSP processor, a stereo audio codec and a
battery charger making it ideal for portable
battery Bluetooth stereo or hands-free audio
applications. WT32 provides an ideal solution
for developers that want to quickly integrate
latest Bluetooth audio technologies into their
design without investing several months
into Bluetooth radio and stack development.
On addition to the standard Bluetooth audio
profiles WT32 also can support aptX® audio
coding technology offering
outstanding Bluetooth Stereo audio quality,
CVC echo cancellation software for hands-
free applications and Apple iAP profile
enabling OEMs to create really unique and
differentiated audio products.
APPLICATIONS:
Stereo and mono speakers
Speakerphones
Hi-Fi Audio devices
Hands-free car kits
KEY FEATURES:
Radio features:
Bluetooth v.2.1 + EDR
Bluetooth class 2 radio
Transmit power: +7 dBm
Receiver sensitivity: -86 dBm
Integrated chip antenna or W.FL
connector
Hardware features:
UART host interfaces
802.11 co-existence interface
10 software programmable IO pins
Li-Ion and Li-Poly battery charger
Opertating voltage: 1.8V to 3.6V
Temperature range: -30C to +85C
Dimensions: 35.75 x 14.50 x 2.6mm
Audio features:
Analog, I2S, PCM and SPDIF
interfaces
Microphone input
Integrated DSP
Integrated stereo audio codec
Qualifications:
Bluetooth
CE
FCC
IC
Japan
9
1 Ordering Information
*) Custom firmware refers to any standard firmware with custom parameters (like UART baud rate),
custom firmware developed by customer, or custom firmware developed by Bluegiga for the customer.
To order custom firmware, you must have a properly filled Custom Firmware Order Form and a unique
ordering code issued by Bluegiga.
WT32-A-AI
Product series
Fimrware
AI5 = iWRAP 5.0.0
AI4 = iWRAP 4.0.0
C = custom *)
HW version
A = Chip antenna, industrial temperature
range
E = W.FL connector, industrial
temperature range
10
2 Block Diagram and Descriptions
Figure 1: Block diagram of WT32
BC05-MM
The BlueCore05-MM is a single-chip radio and baseband IC for Bluetooth 2.4GHz systems. It provides
a fully compliant Bluetooth system to v2.0+EDR of the specification for data and voice.
BlueCore05-MM contains the Kalimba DSP co-processor with double the MIPS of BlueCore03-MM,
supporting enhanced audio applications. BlueCore05-MM integrates a 16-bit stereo codec and it has a
fully differential audio interface with a low noise microphone bias.
Crystal
The crystal oscillates at 26MHz.
Flash
Flash memory is used for storing the Bluetooth protocol stack and Virtual Machine applications. It can
also be used as an optional external RAM for memory-intensive applications.
Balanced Filter
Combined balun and filter changes the balanced input/output signal of the module to unbalanced signal
of the antenna. The filter is a band pass filter (ISM band).
Antenna
WT32 uses ceramic chip antenna with high dielectric constant, which makes the antenna very
insensitive to surrounding environment and thus gives high design freedom around the antenna.
USB
The USB interface is a full speed Universal Serial Bus (USB) interface for communicating with other
compatible digital devices. WT32 acts as a USB peripheral, responding to requests from a Master host
controller such as a Personal Computer (PC).
11
Synchronous Serial Interface
This interface is a synchronous serial port interface (SPI) for interfacing with other digital devices. The
SPI port can be used for system debugging. It can also be used for programming the Flash memory.
UART
This interface is a standard Universal Asynchronous Receiver Transmitter (UART) interface for
communicating with other serial devices.
PCM / I2S / SPDIF Interface
This interface is a bi-directional serial programmable audio interface supporting PCM, I2S and SPDIF
formats.
NOTE: the S/PDIF interface is not recommended for use at this time due to an issue with the low-
level BlueCore05-MM firmware revision in use by iWRAP. The audio quality suffers because the
left and right channels get out of sync.
Audio Interface
The audio interface of WT32 has fully differential inputs and outputs and a microphone bias output. A
high-quality stereo audio Bluetooth application can be implemented with minimum amount of external
components.
Programmable I/O
WT32 has a total of 10 digital programmable I/O terminals. These are controlled by the firmware running
on the device.
Reset
WT32 has a reset circuitry that is used to reset the module in the startup to ensure proper operation of
the flash memory. Alternatively, the reset can be externally driven by using a WT32 reset pin.
802.11 Coexistence Interface
Dedicated hardware is provided to implement a variety of coexistence schemes. Channel skipping AFH
(Adaptive Frequency Hopping), priority signaling, channel signaling, and host passing of channel
instructions are all supported. The features are configured in firmware. Since the details of some
methods are proprietary (e.g. Intel WCS), please contact Bluegiga Technologies for details.
12
3 Electrical Characteristics
3.1 Absolute maximum ratings
Min
Max
Unit
Storage temperature
-40
85
°C
Operating temperature
-30
85
°C
VDD_IO
-0.4
3.6
V
VDD_BAT
-0.4
4.4
V
VDD_CHG
-0.4
6.5
V
Terminal voltages
-0.4
Vdd + 0,4
V
The module should not continuously run under these conditions. Exposure to absolute maximum rating conditions
for extended periods of time may affect reliability and cause permanent damage to the device.
Table 1: Absolute maximum ratings
3.2 Recommended operating conditions
Min
Max
Unit
Operating temperature
-30
85
°C
VDD_IO
1.7
3.6
V
VDD_BAT
2.5
4.4
V
VDD_CHG
0
6.5
V
Terminal voltages
0
Vdd
V
Table 2: Recommended operating conditions
13
3.3 Terminal characteristics
Min
Typ
Max
Unit
I/O voltage levels
VIL input logic level low
-0.4
-
0.25xVDD
V
VIH input logic level high
0.625xVDD
-
Vdd + 0.3
V
VOL output logic level low
0
-
0.125
V
VOH output logic level high
0.75xVDD
-
VDD
V
Reset terminal
VTH,res threshold voltage
0.64
0.85
1.5
V
RIRES input resistance
220
k
CIRES input capacitance
220
nF
Input and tri-state current with
Strong pull-up
-100
-40
-10

Strong pull-down
10
40
100

Weak pull-up
-5
-1
-0.2

Weak pull-down
0.2
1
5

I/O pad leakage current
-1
0
1

LED driver pad
Off current
-
1
2

On resistance (VPAD < 0.5 V)
-
20
33

On resistance, pad enabled by battery charger
(VPAD < 0.5 V)
-
20
50

Table 3: Terminal characteristics
14
3.4 Battery charger
Battery charger
Min
Typ
Max
Unit
VDD_CHG
4.5
-
6.5
V
Charging mode (VDD_BAT rising to 4.2 V)
Supply current (a)
-
4.5
6
mA
Battery trickle charge
current (b) (c)
Maximum setting
-
14
-
mA
Minimum setting
-
4
-
mA
Maximum battery fast
charge current (d) (c)
Headroom > 0.7 V (e)
-
140
-
mA
Headroom = 0.3 V
-
120
-
mA
Minimum battery fast
charge current (d) (c)
Headroom > 0.7 V
-
40
-
mA
Headroom = 0.3 V
-
35
-
mA
Trickle charge voltage threshold
-
2.9
-
V
Float voltage (with correct trim value set),
VFLOAT(f)
4.17
4.2
4.23
V
Float voltage trim step size (f)
-
50
-
mV
Battery charge termination current, as a
percentage of the fast charge current
5
10
20
%
Standby Mode (BAT_P falling from 4.2V)
Supply current (a)
-
1.5
2
mA
Battery current
-
-5
-
μA
Battery recharge hysteresis (g)
100
-
200
mV
Shutdown Mode (VDD_CHG too low or disabled by firmware)
VDD_CHG under-
voltage
threshold
VDD_CHG rising
-
3.9
-
V
VDD_CHG falling
-
3.7
-
V
VDD_CHG - BAT_P
lockout
threshold
VDD_CHG rising
-
0.22
-
V
VDD_CHG falling
-
0.17
-
V
Supply current
-
1.5
2
mA
Battery current
-1
-
0
μA
(a) Current into VDD_CHG - does not include current delivered to battery (I VDD_CHG - I BAT_P)
(b) BAT_P < Float voltage
(c) Charge current can be set in 16 equally spaced steps
(d) Trickle charge threshold < BAT_P < Float voltage
(e) Where headroom = VDD_CHG - BAT_P
(f) Float voltage can be adjusted in 15 steps. Trim setting is determined in production test and must be loaded into the battery
charger by firmware during boot-up sequence
(g) Hysteresis of (VFLOAT - BAT_P) for charging to restart
Table 4: Battery charger characteristics
15
Stereo CODEC Analogue to Digital Converter
Parameter
Conditions
Min
Typ
Max
Unit
Resolution
-
-
16
Bits
Input Sample Rate,
Fsample
8
-
44.1
kHz
Signal to Noise
Ratio, SNR
fin = 1kHz
B/W = 20Hz→20kHz
A-Weighted
THD+N < 1%
150mVpk-pk input
Fsample
8 kHz
-
82
-
dB
11.025 kHz
-
81
-
dB
16 kHz
-
80
-
dB
22.050 kHz
-
79
-
dB
32 kHz
-
79
-
dB
44.1 kHz
-
78
-
dB
Digital Gain
Digital Gain Resolution = 1/32dB
-24
-
21.5
dB
Analogue Gain
Analogue Gain Resolution = 3dB
-3
-
42
dB
Input full scale at maximum gain (differential)
-
4
-
mV rms
Input full scale at minimum gain (differential)
-
800
-
mV rms
3dB Bandwidth
-
20
-
kHz
Microphone mode input impedance
-
6.0
-
kΩ
THD+N (microphone input) @ 30mV rms input
-
0.04
-
%
Table 5: Stereo CODEC ADC characteristics
Stereo CODEC Digital to Analog Converter
Parameter
Conditions
Min
Typ
Max
Unit
Resolution
-
-
16
Bits
Input Sample
Rate, Fsample
8
-
48
kHz
Signal to Noise
Ratio, SNR
fin = 1kHz
B/W = 20Hz→20kHz
A-Weighted
THD+N < 1%
150mVpk-pk input
Fsample
8 kHz
-
95
-
dB
11.025 kHz
-
95
-
dB
16 kHz
-
95
-
dB
22.050 kHz
-
95
-
dB
32 kHz
-
95
-
dB
44.1 kHz
-
95
-
dB
Digital Gain
Digital Gain Resolution = 1/32dB
-24
-
21.5
dB
Analogue Gain
Analogue Gain Resolution = 3dB
0
-
-21
dB
Output voltage full scale swing (differential)
-
750
-
mV rms
Allowed Load
Resistive
16(8)
-
OC
Ω
Capacitive
-
-
500
pF
THD+N 100kΩ load
-
-
0.01
%
THD+N 16Ω load
-
-
0.1
%
SNR (Load = 16Ω, 0dBFS input relative to digital silence)
-
95
-
dB
Table 6: Stereo CODEC DAC characteristics
16
3.5 Radio characteristics and general specifications
Specification
Note
Operating frequency range
(2400 ... 2483,5) MHz
ISM Band
Lower quard band
2 MHz
Upper quard band
3,5 MHz
Carrier frequency
2402 MHz ... 2480 MHz
f = 2402 + k,
k = 0...78
Modulation method
GFSK (1 Mbps)
/4 DQPSK (2Mbps)
8DQPSK (3Mbps)
Hopping
1600 hops/s, 1 MHz channel space
Maximum data rate
GFSK:
Asynchronous, 723.2 kbps
/ 57.6 kbps
Synchronous: 433.9 kbps /
433.9 kbps
/4 DQPSK:
Asynchronous, 1448.5
kbps / 115.2 kbps
Synchronous: 869.7 kbps /
869.7 kbps
8DQPSK:
Asynchronous, 2178.1
kbps / 177.2 kbps
Synchronous: 1306.9 kbps
/ 1306.9 kbps
Receiver IF frequency
1.5 MHz
Center frequency
Transmission power*
Min
-2dBm
Max
2 dBm
RF input impedance
50
Compliance
Bluetooth specification, version 2.1 + EDR
USB specification
USB specification, version 1.1 (USB 2.0
compliant)
*) Related to WT32-A where the maximum TX power is limited by default to nominal 0
dBm by the iWRAP firmware.
Table 7: Radio characteristics and general specifications
17
Bottom side
of WT32EK
3.6 Radio Characteristics
DH1 3DH5 DH1 3DH5
Sensitivity (0.1% BER) -87 dBm -81 dBm -87 dBm -81 dBm
Max output power (typical) 0 dBm -1 dBm 8 dBm 5 dBm
(*) Measured from the antenna
WT32-A (*)
WT32-E (**)
(**) Measured from the w-fl connector - In WT32-E the iWRAP firmware is
configured by default for higer output power than in WT32-A
3.6.1 Radiation Pattern (WT32EK)
o Peak gain = 1.5 dBi
o Total efficiency = 50%
18
4 WT32 Pin Description
AUDIO_OUT_N_LEFT
AUDIO_OUT_P_LEFT
AUDIO_OUT_P_RIGHT
AUDIO_OUT_N_RIGHT
AGND
AUDIO_IN_N_LEFT
AUDIO_IN_P_LEFT
AGND
AUDIO_IN_N_RIGHT
AUDIO_IN_P_RIGHT
MIC_BIAS
AGND
VDD_CHG
VDD_BAT
LED0
SPI_MOSI
SPI_MISO
SPI_CLK
SPI_NCSB
PCM_CLK
PCM_SYNC
PCM_OUT
PCM_IN
PIO4
PIO5
PIO6
PIO7
PIO8
UART_NCTS
UART_NRTS
RESET
DGND
VDD_IO
UART_TXD
UART_RXD
PIO10
PIO9
USB_D+
USB_D-
PIO3
PIO2
PIO1
PIO0
AIO1
AIO0
DGND
DGND
DGND
RF
1
17 31
50
RFTP
DGND
VREG_ENA
Figure 2: WT32 connection diagram (top view)
NOTE: VREG_ENA pin is only available with the production version of the module. With engineering
samples the VREG_ENA is internally connected to VDD_BAT.
DEVICE TERMINALS
1
VREG_ENA
2
DGND
3
DGND
4
DGND
5
AIO1
6
AIO0
7
PIO0
8
PIO1
9
PIO2
10
PIO3
11
USB_DN
12
USB_DP
13
PIO9
14
PIO10
15
RXD
16
TXD
17
VDD_IO
18
DGND
19
RESET
19
20
RTS#
21
CTS#
22
PIO8
23
PIO7
24
PIO6
25
PIO5
26
PIO4
27
PCM_IN
28
PCM_OUT
29
PCM_SYNC
30
PCM_CLK
31
DGND
32
SPI_CS#
33
SPI_CLK
34
SPI_MISO
35
SPI_MOSI
36
LED0
37
VDD_BAT
38
VDD_CHG
39
AGND
40
MIC_BIAS
41
AUDIO_IN _P_RIGHT
42
AUDIO_IN _N_RIGHT
43
AGND
44
AUDIO_IN _P_LEFT
45
AUDIO_IN_N_LEFT
46
AUDIO_OUT _N_RIGHT
47
AUDIO_OUT _P_RIGHT
48
AGND
49
AUDIO_OUT_N_LEFT
50
AUDIO_OUT_P_LEFT
RFTP
RF test point
Table 8: WT32 device terminals
4.1 Device Terminal Functions
DGND
Connect digital GND pins to the ground plane of the PCB.
AGND
Ground for the audio signals. AGND and DGND are internally combined in WT32. Use solid ground
plane for AGND and keep AGND and DGND planes separated.
VDD_IO
Supply voltage connection for the digital I/Os of the module. Supply voltage at this pin can vary between
1.8 V and 3.3 V. Output voltage swing at the digital terminals of WT32 is 0 to VDD_IO.
20
VDD_BAT
Input for an internal 1.8 V switched mode regulator combined with output of the internal battery charger.
See chapter 5.3 for detailed description for the charger. When not powered from a battery, VDD_IO and
VDD_BAT can be combined to a single 3.3 V supply voltage.
VREG_ENA
Enable pin for the internal 1,8 V regulator. This pin is only available with production version. With the
engineering samples VREG_ENA is internally connected to VDD_BAT.
VDD_CHG
Charger input voltage. The charger will start operating when voltage to this pin is applied. When the
charger is not used, this pin should be left floating. See chapter 5.3 for detailed description of the
charger.
RES
The RESET pin is an active high reset and is internally filtered using the internal low frequency clock
oscillator. A reset will be performed between 1.5 and 4.0ms following RESET being active. It is
recommended that RESET be applied for a period greater than 5ms.
WT32 has an internal reset circuitry, which keeps the reset pin active until supply voltage has reached
stability in the start up. This ensures that supply for the flash memory inside the WT32 will reach stability
before BC4 chip fetches instructions from it. Schematic of the reset circuitry is shown in Figure 3. Rising
supply voltage charges the capacitor, which will activate the reset of WT32. The capacitor discharges
through 220 k resistor, which eventually deactivates the reset. Time constant of the RC circuitry is set
in a way that the supply voltage is safely stabilized before the reset deactivates. Pull-up or pull-down
resistor should not be connected to the reset pin to ensure proper start up of WT32. If the reset pin of
WT32 is in use, the designer should verify that WT32 remains in reset during a start-up until all supply
voltages have stabilized.
Figure 3: WT32 internal reset circuitry
See chapter 4 for detailed description of reset.
21
PIO0 PIO10
Programmable digital I/O lines. All PIO lines can be configured through software to have either weak or
strong pull-ups or pull-downs. Configuration for each PIO line depends on the application. See section
10 “I/O parallel ports” for detailed descriptions for each terminal. Default configuration for all of the PIO
lines is input with weak internal pull-up.
AIO0 AIO1
AIOs can be used to monitor analogue voltages such as a temperature sensor for the battery charger.
AIOs can also be configured to be used as digital I/Os. The voltage level at these pins is 0 V to 1,5 V.
UART_NRTS
A CMOS output with a weak internal pull-up. This pin can be used to implement RS232 hardware flow
control where RTS (request to send) is an active low indicator. The UART interface requires an external
RS232 transceiver chip.
UART_NCTS
A CMOS input with a weak internal pull-down. This pin can be used to implement RS232 hardware flow
control where CTS (clear to send) is an active low indicator. The UART interface requires an external
RS232 transceiver chip.
UART_RXD
A CMOS input with a weak internal pull-down. RXD is used to implement UART data transfer from
another device to WT32. The UART interface requires an external RS232 transceiver chip.
UART_TXD
A CMOS output with a weak internal pull-up. TXD is used to implement UART data transfer from WT32
to another device. The UART interface requires external RS232 transceiver chip.
22
PCM_OUT
A CMOS output with a weak internal pull-down. Used in the PCM (pulse code modulation) interface to
transmit digitized audio. The PCM interface is shared with the I2S interface.
PCM_IN
A CMOS input with a weak internal pull-down. Used in the PCM interface to receive digitized audio. The
PCM interface is shared with the I2S interface.
PCM_CLK
A bi-directional synchronous data clock signal pin with a weak internal pull-down. PCMC is used in the
PCM interface to transmit or receive the CLK signal. When configured as a master, WT32 generates the
clock signal for the PCM interface. When configured as a slave, the PCMC is an input and receives the
clock signal from another device. The PCM interface is shared with the I2S interface.
PCM_SYNC
A bi-directional synchronous data strobe with a weak internal pull-down. When configured as a master,
WT32 generates the SYNC signal for the PCM interface. When configured as a slave, the PCMS is an
input and receives the SYNC signal from another device. The PCM interface is shared with the I2S
interface.
USB_D+
A bi-directional USB data line with a selectable internal 1.5 k pull-up implemented as a current source
(compliant with USB specification v1.2) An external series resistor is required to match the connection
to the characteristic impedance of the USB cable.
USB_D-
A bi -directional USB data line. An external series resistor is required to match the connection to the
characteristic impedance of the USB cable.
SPI_NCSB
A CMOS input with a weak internal pull-down. Active low chip select for SPI (serial peripheral interface).
SPI_CLK
A CMOS input for the SPI clock signal with a weak internal pull-down. WT32 is the slave and receives
the clock signal from the device operating as a master.
SPI_MISO
An SPI data output with a weak internal pull-down.
SPI_MOSI
An SPI data input with a weak internal pull-down.
RF
This pin can be used when not using a chip antenna or w.fl connector of the module.
AUDIO_IN_P_RIGHT and AUDIO_IN_N_RIGHT
23
Right channel audio inputs. This dual audio input can be configured to be either single-ended or fully
differential and programmed for either microphone or line input. Route differential pairs close to each
other and use a solid dedicated audio ground plane for the audio signals.
AUDIO_IN_P_LEFT and AUDIO_IN_N_LEFT
Left channel audio input. ESD protection and layout considerations similar to right channel audio should
be used.
AUDIO_OUT_P_RIGHT and AUDIO_OUT_N_RIGHT
Right channel audio output. The audio output lines should be routed differentially to either the speakers
or to the output amplifier, depending on whether or not a single-ended signal is required. Use low
impedance ground plane dedicated for the audio signals.
AUDIO_OUT_P_LEFT and AUDIO_OUT_N_LEFT
Left channel audio output. The same guidelines apply to this section as discussed previously.
MIC_BIAS
Bias voltage output for a microphone. Use the same layout guidelines as discussed previously with
other audio signals.
LED0
WT32 includes a pad dedicated to driving LED indicators. This terminal may be controlled by firmware
and it can also be set by the battery charger. The terminal is an open-drain output, so the LED must be
connected from a positive supply rail to the pad in series with a current limiting resistor.
It is recommended that the LED pad is operated with a pad voltage below 0.5V. In this case, the pad
can be thought of as a resistor, RON. The resistance together with the external series resistor will set
the current, ILED, in the LED. Value for the external series resistance can be calculated from the
Equation 1
ON
LED
F
LED R
IVVDD
R
Equation 1: LED series resistor
Where VF is the forward voltage drop of the LED, ILED is the forward current of the LED and RON is the
on resistance (typically 20 Ω) of the LED driver.
24
5 Power Control
5.1 Power Supply Configuration
WT32 contains an internal battery charger and a switch mode regulator that is mainly used for internal
blocks of the module. The module can be powered from a single 3.3 V supply provided that VDD_CHG
is floating. Alternatively the module can be powered from a battery connected to VDD_BAT and using
an external regulator for VDD_IO. 1.8 V to 3.3 V supply voltage for VDD_IO can be used to give desired
signal levels for the digital interfaces of the module. USB, however, requires 3.3 V for proper operation
and thus, when USB is in use, 3.3 V for VDD_IO is mandatory.
AIO pins of the module use 1.8 V from the internal regulator and thus voltage level with these pins is
within 0 V and 1.8 V.
VDD_BAT Switch mode 1,8 V
regulator
VDD_IO
Battery Charger
In
Out
VDD_CHG AIO
Audio
RF
Flash
PIO
USB
UART
PCM
VREG_ENA
Figure 4: Power supply configuration of WT32
5.2 Voltage Regulator Enable Pin
The regulator enable pin VREG_ENA is used to enable WT32. VREG_ENA enables the on-chip
switched mode regulator.
VREG_ENA is active high, with a logic threshold of around 1V, and it has weak pull-down. It can
tolerate voltages up to 4.9V, so it may be connected directly to a battery to enable the device.
VREG_ENA can be configured with iWRAP to either latch on/off the internal regulators at the rising
edge of the input voltage, or to latch the regulators on at the rising edge and shut down the regulators at
the falling edge. Following figure shows an example of how to to implement a power on/off button using
the latch feature. See iWRAP user guide for the details on configuration.
25
Figure 5: Example of how to make a power on/off button using latch feature of the internal
regulators
In Figure 5 the internal regulators are latched on at the rising edge, i.e when pressing SW1. One of the
PIOs is configured to power hold thus keeping the external regulator on until shut down by pressing
SW1 again.
5.3 Battery Charger
The battery charger is a constant current / constant voltage charger circuit, and is suitable for lithium
ion/polymer batteries only. It shares a connection to the battery terminal, VDD_BAT, with the switch-
mode regulator. The charger is initially calibrated by Bluegiga Technologies to have Vfloat = 4.2 V.
The constant current level can be varied to allow charging of different capacity batteries. WT32 allows a
number of different currents to be used in the battery charger hardware. Values written to PS key
0x039b CHARGER_CURRRENT in the range 1..15 specify the charger current from 40..135mA in even
steps. Values outside the valid 0..15 range result in no change to the charging current. The default
charging current (Key = 0) is nominally
40mA. Setting 0 is interpreted as “no-change” so will be ignored
The charger enters various states of operation as it charges a battery. These are shown below:
Off: entered when the charger is disconnected.
Trickle Charge: entered when the battery voltage is below 2.9V.
Fast Charge - Constant Current: entered when the battery voltage is above 2.9V.
26
Fast Charge - Constant Voltage: entered when the battery has reached Vfloat, the
charger switches mode to maintain the cell voltage at Vfloat voltage by adjusting the
constant charge current.
Standby: this is the state when the battery is fully charged and no charging takes
place.
When a voltage is applied to the charger input terminal VDD_CHG, and the battery is not fully charged,
the charger will operate and a LED connected to the terminal LED0 will illuminate. By default, until the
firmware is running, the LED will pulse at a low-duty cycle to minimize current consumption.
The battery charger circuitry auto-detects the presence of a power source, allowing the firmware to
detect, using an internal status bit, when the charger is powered. Therefore, when the charger supply is
not connected to VDD_CHG, the terminal must be left open circuit. The VDD_CHG pin, when not
connected, must be allowed to float and not be pulled to a power rail. When the battery charger is not
enabled, this pin may float to a low undefined voltage. Any DC connection will increase current
consumption of the device. Capacitive components such as diodes, FETs, and ESD protection, may be
connected.
The battery charger is designed to operate with a permanently connected battery. If the application
permits the charger input to be connected while the battery is disconnected, the VDD_BAT pin voltage
may become unstable. This, in turn, may cause damage to the internal switch-mode regulator.
Connecting a 470μF capacitor to VDD_BAT limits these oscillations thus preventing damage.
WARNING:
Use good consideration for battery safety. Do not charge with too much current. Do
not charge when the temperature is above 60°C or below 0°C. WT32 is initially
calibrated to stop charging when battery voltage is at 4.2 V. Do not try to charge
batteries above 4.2 V. Do not short circuit the battery or discharge below 1.5 V.
5.4 RESET
WT32 may be reset from several sources: reset pin, power on reset, a UART break character or through
software configured watchdog timer.
The power on reset occurs when the VDD_CORE supply falls below typically 1.26V and is released
when VDD_CORE rises above typically 1.31V. At reset, the digital I/O pins are set to inputs for bi-
directional pins and outputs are tri-state. The pull-down state is shown in Table 9.
The chip status after a reset is as follows:
Warm Reset: data rate and RAM data remain available
Cold Reset(10): data rate and RAM data are not available
Table 9 shows the pin states of WT32 on reset. Pull-up (PU) and pull-down (PD) default to weak values
unless specified otherwise.
Pin Name /
Group
I/O Type
State on Reset
USB_D+
Digital bi-directional
N/A
USB_D-
Digital bi-directional
N/A
UART_RX
Digital input with PD
PD
UART_CTS
Digital input with PD
PD
UART_TX
Digital bi-directional with PU
PU
UART_RTS
Digital bi-directional with PU
PU
SPI_MOSI
Digital input with PD
PD
SPI_CLK
Digital input with PD
PD
SPI_CS#
Digital input with PU
PU
SPI_MISO
Digital tri-state output with PD
PD
PCM_IN
Digital input with PD
PD
PCM_CLK
Digital bi-directional with PD
PD
27
PCM_SYNC
Digital bi-directional with PD
PD
PCM_OUT
Digital tri-state output with PD
PD
PIO[10:0]
Digital bi-directional with PU/PD
PD
Table 9: Pin states on reset
28
6 Serial Interfaces
6.1 UART Interface
WT32 Universal Asynchronous Receiver Transmitter (UART) interface provides a simple mechanism for
communicating with other serial devices using the RS232 standard. The UART interface of WT32 uses
voltage levels from 0 to VDD_IO and thus an external transceiver IC is required to meet the voltage
level specifications of RS232.
Figure 6: WT32 UART interface
Four signals are used to implement the UART function, as shown in Figure 7Figure 6. When WT32 is
connected to another digital device, UART_RX and UART_TX transfer data between the two devices.
The remaining two signals, UART_CTS and UART_RTS, can be used to implement RS232 hardware
flow control where both are active low indicators. DTR, DSR and DCD signals can be implemented by
using PIO terminals of WT32. All UART connections are implemented by using CMOS technology and
have signaling levels of 0V and VDD_IO.
In order to communicate with the UART at its maximum data rate using a standard PC, an accelerated
serial port adapter card is required for the PC.
Parameter
Possible values
Baud rate
Minimum
1200 baud (≤2%Error)
9600 baud (≤1%Error)
Maximum
3.0Mbaud (≤1%Error)
Flow control
RTS/CTS, none
Parity
None, Odd, Even
Number of stop bits
1 or 2
Bits per channel
8
Table 10: Possible UART settings
The UART interface is capable of resetting WT32 upon reception of a break signal. A Break is identified
by a continuous logic low (0V) on the UART_RX terminal, as shown in Figure 7. If tBRK is longer than
the value, defined by the PS Key PSKEY_HOST_IO_UART_RESET_TIMEOUT, (0x1a4), a reset will
occur. This feature allows a host to initialize the system to a known state. Also, WT32 can emit a Break
character that may be used to wake the Host.
Since UART_RX terminal includes a weak internal pull-down, it cannot be left open unless disabling
UART interface using PS_KEY settings. If UART is not disabled, a pull-up resistor has to be connected
to UART_RX. The UART interface requires an external RS232 transceiver, which usually includes the
required pull-up.
UART_TX
UART_RX
UART_RTS
UART_CTS
WT32
29
tBRK
UART_RX
Figure 7: Break signal
Table 11 shows a list of commonly used Baud rates and their associated values for the Persistent Store
Key PSKEY_UART_BAUDRATE (0x204). There is no requirement to use these standard values. Any
Baud rate within the supported range can be set in the Persistent Store Key according to the formula in
Equation below.
Baud Rate = PSKEY_UART_BAUD_RATE
0.004096
Equation 2: Baud rate calculation formula
Hex Dec
1200 0x0005 5 1.73%
2400 0x000a 10 1.73%
4800 0x0014 20 1.73%
9600 0x0027 39 -0.82%
19200 0x004f 79 0.45%
38400 0x009d 157 -0.18%
57600 0x00ec 263 0.03%
76800 0x013b 315 0.14%
115200 0x01d8 472 0.03%
230400 0x03b0 944 0.03%
460800 0x075f 1887 -0.02%
921600 0x0ebf 3775 0.00%
1382400 0x161e 5662 -0.01%
1843200 0x1d7e 7550 0.00%
2765800 0x2c3d 11325 0.00%
Persistent store values
Baud rate
Error
Table 11: UART baud rates and error values
6.1.1 UART Configuration While RESET is Active
The UART interface for WT32 while the chip is being held in reset is tri-state. This will allow the user to
daisy chain devices onto the physical UART bus. The constraint on this method is that any devices
connected to this bus must tri-state when a WT32 reset is de-asserted and the firmware begins to run.
6.1.2 UART Bypass Mode
Alternatively, for devices that do not tri-state the UART bus, the UART bypass mode on WT32 can be
used. The default state of WT32 after reset is de-asserted, this is for the host UART bus to be
connected to the WT32 UART, thereby allowing communication to WT32 via the UART.
In order to apply the UART bypass mode, a BCCMD command will be issued to WT32. Upon this,
WT32 will switch the bypass to PIO[7:4] as shown in Figure 8. Once the bypass mode has been
invoked, WT32 will enter the deep sleep state indefinitely.
In order to re-establish communication with WT32, the chip must be reset so that the default
configuration takes effect.
30
It is important for the host to ensure a clean Bluetooth disconnection of any active links before the
bypass mode is invoked. Therefore, it is not possible to have active Bluetooth links while operating the
bypass mode.
The current consumption for a device in UART Bypass Mode is equal to the values quoted for a device
in standby mode.
WT12
Host
processor
Test
interface
RXD
CTS
RTS
TXD
Another
device
TX
RTS
CTS
RX
UART_TX
UART_RTS
UART_CTS
UART_RX
RESET
PIO5
PIO6
PIO7
PIO4
UART
WTxx
Figure 8: UART bypass mode
31
6.2 USB Interface
WT32 USB devices contain a full speed (12Mbits/s) USB interface that is capable of driving a USB
cable directly. No external USB transceiver is required. To match the connection to the characteristic
impedance of the USB cable, series resistors must be included to both of the signal lines. These should
be of 1% tolerance and the value required may vary between 0 and 20 ohm with 10 ohm being nominal.
The resistors should be placed close to the USB pins of the module in order to avoid reflections.
Internally, the module has 22-ohm resistors in series. The total input impedance seen by the cable is
affected by the IC characteristics, track layout and the connector. The cable impedance is
approximately 40 ohms.
The device operates as a USB peripheral, responding to requests from a master host controller such as
a PC. Both the OHCI and the UHCI standards are supported. The set of USB endpoints implemented
can behave as specified in the USB section of the Bluetooth v2.0 + EDR specification or alternatively
can appear as a set of endpoints appropriate to USB audio devices such as speakers.
As USB is a Master/Slave oriented system (in common with other USB peripherals), WT32 only
supports the USB Slave operation.
6.2.1 USB Pull-Up Resistor
WT32 features an internal USB pull-up resistor. This pulls the USB_DP pin weakly high when WT32 is
ready to enumerate. It signals to the PC that it is a full speed (12Mbit/s) USB device.
The USB internal pull-up is implemented as a current source, and is compliant with Section 7.1.5 of the
USB specification v1.2. The internal pull-up pulls USB_D+ high to at least 2.8V when loaded with a
15k +/-5% pull-down resistor (in the hub/host). This presents a Thevenin resistance to the host of at
least 900. Alternatively, an external 1.5k pull-up resistor can be placed between a PIO line and D+
on the USB cable. The firmware must be alerted as to which mode is used by setting PS Key
PSKEY_USB_PIO_PULLUP appropriately. The default setting uses the internal pull-up resistor.
6.2.2 Self Powered Mode
In self powered mode, the circuit is powered from its own power supply and not from the VBUS (5V) line
of the USB cable. It only draws a small leakage current (below 0.5mA) from VBUS on the USB cable.
This is the easier mode which to design for, as the design is not limited by the power that can be drawn
from the USB hub or root port. However, it requires that VBUS be connected to WT32 via a voltage
divider (Rvb1 and Rvb2), so that WT32 can detect when VBUS is powered up. The voltage divider is
essential to drop the 5V voltage at the VBUS to 3.3V expected at the USB interface of WT32. WT32 will
not pull USB_DP high when VBUS is off.
Self powered USB designs (powered from a battery or PSU) must ensure that a PIO line is allocated for
USB pull-up purposes. A 1.5K 5% pull-up resistor between USB_DP and the selected PIO line should
be fitted to the design. Failure to fit this resistor may result in the design failing to be USB compliant in
the self powered mode. The internal pull-up in WT32 is only suitable for bus powered USB devices,
such as dongles.
PIO
USB_D+
USB_D-
USB_ON
R =1.5k
Rvb1
WT12
Rvb2
WT32
Figure 9: USB in self powered mode
32
The terminal marked USB_ON can be any free PIO pin. The PIO pin selected must be registered by
setting PSKEY_USB_PIO_VBUS to the corresponding pin number. In self powered mode,
PSKEY_USB_PIO_PULLUP must be set to match with the PIO selected.
Note:
USB_ON is shared with WT32 PIO terminals (PIO2-PIO7).
6.2.3 Bus Powered Mode
In bus powered mode, the application circuit draws its current from the 5V VBUS supply on the USB
cable. WT32 negotiates with the PC during the USB enumeration stage about how much current it is
allowed to consume.
For WT32 Bluetooth applications, it is recommended that the regulator used to derive 3.3V from VBUS
is rated at 100mA average current and should be able to handle peaks of 120mA without fold back or
limiting. In bus powered mode, WT32 requests 100mA during enumeration.
When selecting a regulator, be aware that VBUS may go as low as 4.4V. The inrush current (when
charging the reservoir and supply decoupling capacitors) is limited by the USB specification (see USB
specification v1.1, Section 7.2.4.1). Some applications may require soft start circuitry to limit inrush
current if more than 10pF is present between VBUS and GND.
The 5V VBUS line emerging from a PC is often electrically noisy. As well as regulation down to 3.3V,
applications should include careful filtering of the 5V line to attenuate noise that is above the voltage
regulator bandwidth.
In bus powered mode, PSKEY_USB_PIO_PULLUP must be set to 16 for internal pull-up (default
configuration in WT32).
USB_D+
USB_D-
USB_ON
Voltage
regulator
WT12
VBUS
GND
WT32
Figure 10: USB in bus powered mode
6.2.4 Suspend Current
All USB devices must permit the USB controller to place them in a USB Suspend mode. While in USB
Suspend, bus powered devices must not draw more than 0.5mA from USB VBUS (self powered devices
may draw more than 0.5mA from their own supply). This current draw requirement prevents operation of
the radio by bus powered devices during USB Suspend.
The voltage regulator circuit itself should only draw a small quiescent current (typically less than 100uA)
to ensure adherence to the suspend current requirement of the USB specification. This is not normally a
problem with modern regulators. Ensure that external LEDs and/or amplifiers can be turned off by
WT32. The entire circuit must be able to enter the suspend mode. (For more details on USB Suspend,
see separate CSR documentation).
6.2.5 Detach and Wake-Up Signaling
WT32 can provide out-of-band signaling to a host controller by using the control lines called
‘USB_DETACH’ and USB_WAKE_UP’. These are outside the USB specification (no wires exist for
them inside the USB cable), but can be useful when embedding WT32 into a circuit where no external
33
USB is visible to the user. Both control lines are shared with PIO pins and can be assigned to any PIO
pin by setting the PS Keys PSKEY_USB_PIO_DETACH and PSKEY_USB_PIO_WAKEUP to the
selected PIO number.
USB_DETACH is an input that, when asserted high, causes WT32 to put USB_D- and USB_D+ in high
impedance state and turns off the pull-up resistor on D+. This detaches the device from the bus and is
logically equivalent to unplugging the device. When USB_DETACH is taken low, WT32 will connect
back to USB and await enumeration by the USB host.
USB_WAKE_UP is an active high output (used only when USB_DETACH is active) to wake up the host
and allow USB communication to recommence. It replaces the function of the software USB WAKE_UP
message (which runs over the USB cable), and cannot be sent while WT32 is effectively disconnected
from the bus.
USB_WAKE_UP
USB_DETACH
Port_Imbedance
USB_DPUSB_DN
USB_PULL_UP
10ms max
10ms max 10ms max
No max
Disconnected
Figure 11: USB_DETACH and USB_WAKE_UP Signal
6.2.6 USB Driver
A USB Bluetooth device driver is required to provide a software interface between WT32 and Bluetooth
software running on the host computer. Suitable drivers are available from www.bluegiga.com/techforum/.
6.2.7 USB 1.1 Compliance
WT32 is qualified to the USB specification v1.1, details of which are available from http://www.usb.org.
The specification contains valuable information on aspects such as PCB track impedance, supply inrush
current and product labeling.
Although WT32 meets the USB specification, Bluegiga Technologies cannot guarantee that an
application circuit designed around the module is USB compliant. The choice of application circuit,
component choice and PCB layout all affect USB signal quality and electrical characteristics. The
information in this document is intended as a guide and should be read in association with the USB
specification, with particular attention being given to Chapter 7. Independent USB qualification must be
sought before an application is deemed USB compliant and can bear the USB logo. Such qualification
can be obtained from a USB plug fest or from an independent USB test house.
Terminals USB_D+ and USB_D- adhere to the USB specification 2.0 (Chapter 7) electrical
requirements.
6.2.8 USB 2.0 Compatibility
WT32 is compatible with USB v2.0 host controllers; under these circumstances the two ends agree the
mutually acceptable rate of 12Mbits/s according to the USB v2.0 specification.
34
6.3 SPI Interface
The synchronous serial port interface (SPI) is for interfacing with other digital devices. The SPI port can
be used for system debugging. It can also be used for programming the Flash memory. SPI interface is
connected by using the MOSI, MISO, CSB and CLK pins.
SPI interface can not be used for any application purposes.
35
7 Audio Interfaces
7.1 Audio Interface
The audio interface circuit consists of:
Stereo audio CODEC
Dual audio inputs and outputs
A configurable PCM, I2S or SPDIF interface
NOTE: the S/PDIF interface is not recommended for use at this time due to an issue with the low-
level BlueCore05-MM firmware revision in use by iWRAP. The audio quality suffers because the
left and right channels get out of sync.
Figure 12 outlines the functional blocks of the interface. The CODEC supports stereo playback and
recording of audio signals at multiple sample rates with a resolution of 16-bit. The ADC and the DAC of
the CODEC each contain two independent channels. Any ADC or DAC channel can be run at its own
independent sample rate.
Figure 12: Audio interface
The interface for the digital audio bus shares the same pins as the PCM CODEC interface described in
section 6.3, which means that each of the audio buses are mutually exclusive in their usage. Table 12
lists these alternative functions.
PCM Interface
SPDIF Interface
I2S Interface
PCM_OUT
SPDIF_OUT
SD_OUT
PCM_IN
SPDIF_IN
SD_IN
PCM_SYNC
WS
PCM_CLK
SCK
Table 12: Alternative functions of the digital audio bus interface on the PCM interface
7.1.1 Audio Input and Output
The audio input circuitry consists of a dual audio input that can be configured to be either single-ended
or fully differential and programmed for either microphone or line input. It has an analogue and digital
programmable gain stage for optimisation of different microphones.
Audio signals are very sensitive to noise caused by the Bluetooth radio and it is highly recommended to
always use fully differential signals.
The audio output circuitry consists of a dual differential class A-B output stage.
36
7.2 Stereo Audio CODEC Interface
The main features of the interface are:
Stereo and mono analogue input for voice band and audio band
Stereo and mono analogue output for voice band and audio band
Support for stereo digital audio bus standards such as I2S
Support for IEC-60958 standard stereo digital audio bus standards, e.g. S/PDIF and
AES3/EBU
Support for PCM interfaces including PCM master CODECs that require an external
system clock
Figure 13: Stereo CODEC audio input and output stages
The stereo audio CODEC uses a fully differential architecture in the analogue signal path, which results
in low noise sensitivity and good power supply rejection while effectively doubling the signal amplitude.
It operates from a single power-supply of 1.5V and uses a minimum of external components.
37
7.2.1 ADC
The ADC consists of two second-order Sigma Delta converters allowing two separate channels that are
identical in functionality, as shown in Figure 13Figure 14.
Each ADC supports the following sample rates:
8kHz
11.025kHz
16kHz
22.05kHz
24kHz
32kHz
44.1kHz
The ADC contains two gain stages for each channel, an analogue and a digital gain stage. The digital
gain stage has a programmable selection value in the range of 0 to 15 with the associated ADC gain
settings summarised in Table 13. There is also a high resolution digital gain mode that allows the gain
to be changed in 1/32dB steps. Please contact Bluegiga Technologies for more information.
Gain SelectionValue
ADC Digital Gain Setting (dB)
0
0
1
3.5
2
6
3
9.5
4
12
5
15.5
6
18
7
21.5
8
-24
9
-20.5
10
-18
11
-14.5
12
-12
13
-8.5
14
-6
15
-2.5
Table 13: ADC digital gain rate selection
The ADC analogue amplifier is a two-stage amplifier. The first stage of the analogue amplifier is
responsible for selecting the correct gain for either microphone input or line input and, therefore, has
two gain settings, one for the microphone and one for the line input. See section 6.2.5 and section 6.2.6
for details on the microphone and line inputs, respectively. In simple terms, the first stage amplifier has
a selectable 24dB gain stage for the microphone and this creates the dual programmable gain required
for the microphone or the line input. The equivalent block diagram for the two stages is shown in Figure
14.
38
Figure 14: ADC analogue amplifier block diagram
The second stage of the analogue amplifier shown in Figure 14 has a programmable gain with seven
individual 3dB steps. In simple terms, by combining the 24dB gain selection of the microphone input
with the seven individual 3dB gain steps, the overall range of the analogue amplifier is approximately -
3dB to 42dB in 3dB steps. The overall gain control of the ADC is controlled by a VM function. See
iWRAP user guide how to set the gain using iWRAP commands.
7.2.2 DAC
The DAC consists of two third-order Sigma Delta converters allowing two separate channels that are
identical in functionality as shown in Figure 14.
Each DAC supports the following samples rates:
8kHz
11.025kHz
16kHz
22.050kHz
24kHz
32kHz
44.1kHz
48kHz
See the iWRAP user guide how to set the sampling rate using iWRAP commands. The default setting
for A2DP is 44.1 kHz and for HFP 8 kHz.
The DAC contains two gain stages for each channel: a digital and an analogue gain stage. The digital
gain stage has a programmable selection value in the range of 0 to 15 with associated DAC gain
settings. This is summarised in Table 14. There is also a high resolution digital gain mode that allows
the gain to be changed in 1/32dB steps. Please contact Bluegiga Technologies for more information.
Gain Selection Value
ADC Digital Gain Setting (dB)
0
0
1
3.5
2
6
3
9.5
4
12
5
15.5
6
18
7
21.5
8
-24
9
-20.5
39
10
-18
11
-14.5
12
-12
13
-8.5
14
-6
15
-2.5
Table 14: DAC digital gain rate selection
The DAC analogue amplifier has a programmable gain with seven individual 3dB steps. The overall gain
control of the DAC is controlled by a VM function. This setting is a combined function of the digital and
analogue amplifier settings, therefore, for a 1V rms nominal digital output signal from the digital gain
stage of the DAC, the following approximate output values of the analogue amplifier of the DAC can be
expected:
Analogue Gain Setting
DAC Gain Setting (dB)
7
3
6
0
5
-3
4
-6
3
-9
2
-12
1
-15
0
-18
Table 15: DAC analogue gain rate selection
7.2.3 IEC 60958 Interface
The IEC 60958 interface is a digital audio interface that uses bi-phase coding to minimize the DC
content of the transmitted signal and allows the receiver to decode the clock information from the
transmitted signal. The IEC 60958 specification is based on the two industry standards AES/EBU and
the Sony and Philips interface specification SPDIF. The interface is compatible with IEC 60958-1, IEC
60958-3 and IEC 60958-4.
The SPDIF interface signals are SPDIF_IN and SPDIF_OUT and are shared on the PCM interface pins.
The input and output stages of the SPDIF pins can interface either to a 75Ω Coaxial cable with an RCA
connector, see Figure 15, or there is an option to use an optical link that uses Toslink optical
components, see Figure 16.
NOTE: the S/PDIF interface is not recommended for use at this time due to an issue with the low-
level BlueCore05-MM firmware revision in use by iWRAP. The audio quality suffers because the
left and right channels get out of sync.
Figure 15: Example circuit for SPDIF interface (Co-Axial)
40
Figure 16: Example circuit for SPDIF interface (Optical)
7.2.4 Microphone Input
The audio-input is intended for use from 1μA@94dB SPL to about 10μA@94dB SPL. With biasing
resistors R1 and R2 equal to 1kΩ, this requires microphones with sensitivity between about 40dBV and
60dBV.
The MIC_BIAS is like any voltage regulator and requires a minimum load to maintain regulation. The
MIC_BIAS will maintain regulation within the limits 0.2 - 1.53 mA depending on the bias current setting.
This means that if a microphone that sits below these limits is used, the microphone output must be pre-
loaded with a large value resistor to ground.
MIC_BIAS line either be used as an enable signal for an external biasing regulator. The default setting
for the bias current in WT32 is 0.2 mA and it is recommended to use an external low noise biasing
regulator for the best noise performance. The recommended microphone biasing circuitry is shown in
the Figure 17.
C3
C4
MIC_BIAS
MIC
AUDIO_IN_P_LEFT
AUDIO_IN_N_LEFT
R1
R2
C1
C2
2V7
regulator
EN
OUT IN VDD_BAT
Figure 17: Recommended microphone biasing (left channel shown)
41
The input impedance at AUDIO_IN_N_LEFT, AUDIO_IN_P_LEFT, AUDIO_IN_N_RIGHT and
AUDIO_IN_P_RIGHT is typically 6.0kΩ. C1 and C2 should be 150nF if bass roll-off is required to limit
wind noise on the microphone. R1 sets the microphone load impedance and is normally in a range of 1
to 2 kΩ. R2, C3 and C4 improve the supply rejection by decoupling supply noise from the microphone.
Values should be selected as required. R1 may be connected to a convenient supply, in which case the
bias network is permanently enabled, or to the output of the biasing regulator which may be configured
to provide bias only when the microphone is required.
The microphone bias provides a 4-bit programmable output voltage with a 4-bit programmable output
current, shown in Table 16 and 17.
Output Step
Typical Voltage Level (V)
0
1.71
1
1.76
2
1.82
3
1.87
4
1.95
5
2.02
6
2.10
7
2.18
8
2.32
9
2.43
10
2.56
11
2.69
12
2.9
13
3.08
14
3.33
15
3.57
Table 16: Voltage Output Step
Output Step
Typical Current (mA)
0
0.199
1
0.284
2
0.336
3
0.419
4
0.478
5
0.529
6
0.613
7
0.672
8
0.754
9
0.809
10
0.862
11
0.948
12
1.004
13
1.091
14
1.142
15
1.229
Table 17: Current Output Step
42
7.2.5 Line Input
If the input analogue gain is set to less than 21dB, WT32 automatically selects line input mode. In line
input mode, the first stage of the amplifier is automatically disabled, providing additional power saving.
In line input mode, the input impedance varies from 6kΩ-30kΩ, depending on the volume setting. Figure
19 and Figure 20 show two circuits for line input operation and show connections for either differential or
single-ended inputs.
Figure 18: Differential input (left channel shown)
Figure 19: Single ended input (left channel shown)
7.2.6 Output Stage
The output digital circuitry converts the signal from 16-bit per sample, linear PCM of variable sampling
frequency to a 2Mbits/s 5-bit multi-bit bit stream, which is fed into the analogue output circuitry.
The output circuit is comprised of a digital to analogue converter with gain setting and an output
amplifier. Its class AB output stage is capable of driving a signal on both channels of up to 2V pk-pk
differential into a load of 16Ω. The output is available as a differential signal between
AUDIO_OUT_N_LEFT and AUDIO_OUT_P_LEFT for the left channel, as Figure 20 shows; and
between AUDIO_OUT_N_RIGHT and AUDIO_OUT_P_RIGHT for the right channel. The output is
capable of driving a speaker directly if its impedance is at least 8Ω at reduced output swing and if only
one channel is connected or an external regulator is used.
Figure 20: Speaker output (left channel shown)
The analogue gain of the output stage is controlled by a 3-bit programmable resistive divider, which sets
the gain in steps of approximately 3dB.
The multi-bit bit stream from the digital circuitry is low pass filtered by a third order filter with a pole at
20kHz. The signal is then amplified in the fully differential output stage, which has a gain bandwidth of
typically 1MHz.
43
7.2.6.1 Mono Operation
Mono operation is a single-channel operation of the stereo CODEC. The left channel represents the
single mono channel for audio in and audio out. In mono operation, the right channel is an auxilliary
mono channel that may be used in dual mono channel operation.
With single mono, the power consumption can be reduced by disabling the other channel.
7.2.6.2 Side Tone
In some applications, it is necessary to implement a side tone. This involves feeding an attenuated
version of the microphone signal to the earpiece. The BlueCore5.Multimedia External CODEC contains
a side tone circuitry to do this. The side tone hardware is configured through the following PS Keys:
PSKEY_SIDE_TONE_ENABLE
PSKEY_SIDE_TONE_GAIN
PSKEY_SIDE_TONE_AFTER_ADC
PSKEY_SIDE_TONE_AFTER_DAC
7.2.6.3 Integrated Digital Filter
TBA
44
7.3 Digital Audio Interface (I2S)
The digital audio interface supports the industry standard formats for I2S, left-justified (LJ) or right-
justified(RJ). The interface shares the same pins as the PCM interface, which means that each audio
bus is mutually exclusive in its usage. Table 18 lists these alternative functions. Figure 22 shows the
timing diagram.
PCM Interface
I2S Interface
PCM_OUT
SD_OUT
PCM_IN
SD_IN
PCM_SYNC
WS
PCM_CLK
SCK
Table 18: Alternative Functions of the Digital Audio Bus Interface on the PCM Interface
Table 19 describes the values for the PS Key (PSKEY_DIGITAL_AUDIO_CONFIG) that is used to set-
up the digital audio interface. For example, to configure an I2S interface with 16-bit SD data set
PSKEY_DIGITAL_CONFIG to 0x0406.
Bit
Mask
Name
Description
D[0]
0x0001
CONFIG_JUSTIFY_FORMAT
0 for left justified, 1 for right justified
D[1]
0x0002
CONFIG_LEFT_JUSTIFY_DELAY
For left justified formats: 0 is MSB of SD data
occurs in the first SCLK period following WS
transition. 1 is MSB of SD data occurs in the
second SCLK period.
D[2]
0x0004
CONFIG_CHANNEL_POLARITY
For 0, SD data is left channel when WS is
high. For 1 SD data is right channel.
D[3]
0x0008
CONFIG_AUDIO_ATTEN_EN
For 0, 17 bit SD data is rounded down to 16
bits. For 1, the audio attenuation defined in
CONFIG_AUDIO_ATTEN is applied over 24
bits with saturated rounding. Requires
CONFIG_16_BIT_CROP_EN to be 0.
D[7:4]
0x00F0
CONFIG_AUDIO_ATTEN
Attenuation in 6 dB steps.
D[9:8]
0x0300
CONFIG_JUSTIFY_RESOLUTION
Resolution of data on SD_IN, 00=16 bit,
01=20 bit, 10=24 bit, 11=Reserved. This is
required for right justified format and with left
justified LSB first.
D[10]
0x0400
CONFIG_16_BIT_CROP_EN
For 0, 17 bit SD_IN data is rounded down to
16 bits. For 1 only the most significant 16 bits
of data are received.
Table 19: PSKEY_DIGITAL_AUDIO_CONFIG
45
Figure 21: Digital audio interface modes
The internal representation of audio samples within BlueCore5.Multimedia External is 16-bit and data on
SD_OUT is limited to 16-bit per channel.
Symbol
Parameter
Min
Typ
Max
Unit
-
SCK Frequency
-
-
6.2
MHz
-
WS Frequency
-
-
96
kHz
tch
SCK high time
80
-
-
ns
tcl
SCK low time
80
-
-
ns
topd
SCK to SD_OUT delay
-
-
20
ns
tssu
WS to SCK set-up time
20
-
-
ns
tsh
WS to SCK hold time
20
-
-
ns
tisu
SD_IN to SCK set-up time
20
-
-
ns
tih
SD_IN to SCK hold time
20
-
-
ns
Table 20: Digital audio interface slave timing
46
Figure 22: Digital audio interface slave timing
Symbol
Parameter
Min
Typ
Max
Unit
-
SCK Frequency
-
-
6.2
MHz
-
WS Frequency
-
-
96
kHz
topd
SCK to SD_OUT delay
-
-
20
ns
tspd
SCK to WS delay
-
-
-
ns
tisu
SD_IN to SCK set-up time
20
-
-
ns
tih
SD_IN to SCK hold time
20
-
-
ns
Table 21: Digital audio interface master timing
Figure 23: Digital audio interface master timing
47
7.4 PCM Interface
Pulse Code Modulation (PCM) is a standard method used to digitize audio (particularly voice) patterns
for transmission over digital communication channels. Through its PCM interface, WT32 has hardware
support for continual transmission and reception of PCM data, thus reducing processor overhead for
wireless headset applications. WT32 offers a bi directional digital audio interface that routes directly into
the baseband layer of the on-chip firmware. It does not pass through the HCI protocol layer.
Hardware on WT32 allows the data to be sent to and received from a SCO connection. Up to three SCO
connections can be supported by the PCM interface at a time.
WT32 can operate as the PCM interface Master generating an output clock of 128, 256 or 512kHz.
When configured as PCM interface slave, it can operate with an input clock up to 2048kHz. WT32 is
compatible with a variety of clock formats, including Long Frame Sync, Short Frame Sync and GCI
timing environments.
WT32 supports 13 or 16-bit linear, 8-bit -law or A-law companded sample formats at 8ksamples/s and
can receive and transmit on any selection of three of the first four slots following PCM_SYNC. The PCM
configuration options are enabled by setting the PS Key PS KEY_PCM_CONFIG32 (0x1b3). WT32
interfaces directly to PCM audio devices including the following:
Qualcomm MSM 3000 series and MSM 5000 series CDMA baseband devices
OKI MSM7705 four channel A-law and -law CODEC
Motorola MC145481 8-bit A-law and -law CODEC
Motorola MC145483 13-bit linear CODEC
STW 5093 and 5094 14-bit linear CODECs
WT32 is also compatible with the Motorola SSI™ interface
7.4.1 PCM Interface Master/Slave
When configured as the Master of the PCM interface, WT32 generates PCM_CLK and PCM_SYNC.
PCM_OUT
PCM_IN
PCM_CLK
PCM_SYNC 8kHz
128/256/512 kHz
WT12
WTxx
Figure 24: WT32 as PCM master
When configured as the Slave of the PCM interface, WT32 accepts PCM_CLK and PCM_SYNC.
PCM_CLK rates up to 2048kHz are accepted.
48
PCM_OUT
PCM_IN
PCM_CLK
PCM_SYNC 8kHz
Up to 2048kHz
WT12
WTxx
Figure 25: WT32 as PCM slave
7.4.2 Long Frame Sync
Long Frame Sync is the name given to a clocking format that controls the transfer of PCM data words or
samples. In Long Frame Sync, the rising edge of PCM_SYNC indicates the start of the PCM word.
When WT32 is configured as PCM Master, generating PCM_SYNC and PCM_CLK, then PCM_SYNC
is 8-bits long. When BlueCore4-External is configured as PCM Slave, PCM_SYNC may be from two
consecutive falling edges of PCM_CLK to half the PCM_SYNC rate, i.e. 62.5s long.
WT32 samples PCM_IN on the falling edge of PCM_CLK and transmits PCM_OUT on the rising edge.
PCM_OUT may be configured to be high impedance on the falling edge of PCM_CLK in the LSB
position or on the rising edge.
12 3 4 5 6 7 8PCM_OUT
PCM_CLK
PCM_SYNC
12 3 4 5 6 7 8
undefined undefined
PCM_IN
Figure 26: Long frame sync (shown with 8-bit companded sample)
7.4.3 Short Frame Sync
In Short Frame Sync, the falling edge of PCM_SYNC indicates the start of the PCM word. PCM_SYNC
is always one clock cycle long.
12 3 4 5 6 7 8PCM_OUT
PCM_CLK
PCM_SYNC
12 3 4 5 6 7 8
undefined
PCM_IN
910 11 12 13 14 15 16
910 11 12 13 14 15 16 undefined
Figure 27: Short frame sync (shown with 16-bit companded sample)
49
As with Long Frame Sync, WT32 samples PCM_IN on the falling edge of PCM_CLK and transmits
PCM_OUT on the rising edge. PCM_OUT may be configured to be high impedance on the falling edge
of PCM_CLK in the LSB position or on the rising edge.
7.4.4 Multi Slot Operation
More than one SCO connection over the PCM interface is supported using multiple slots. Up to three
SCO connections can be carried over any of the first four slots.
12 3 4 5 6 7 8PCM_OUT
PCM_CLK
LONG_PCM_SYNC
12 3 4 5 6 7 8
undefined undefined
PCM_IN
SHORT_PCM_SYNC
OR
Figure 28: Multi slot operation with two slots and 8-bit companded samples
7.4.5 GCI Interface
WT32 is compatible with the General Circuit Interface, a standard synchronous 2B+D ISDN timing
interface. The two 64Kbps B channels can be accessed when this mode is configured.
12 3 4 5 6 7 8PCM_OUT
PCM_CLK
PCM_SYNC
12 3 4 5 6 7 8
undefined
PCM_IN
1 2 3 4 56 7 8
1 2 3 4 56 7 8 undefined
Figure 29: GCI interface
The start of frame is indicated by the rising edge of PCM_SYNC and runs at 8kHz. With WT32 in Slave
mode, the frequency of PCM_CLK can be up to 4.096MHz.
7.4.6 Slots and Sample Formats
WT32 can receive and transmit on any selection of the first four slots following each sync pulse. Slot
durations can be either 8 or 16 clock cycles. Durations of 8 clock cycles may only be used with 8-bit
sample formats. Durations of 16 clocks may be used with 8, 13 or 16-bit sample formats.
WT32 supports 13-bit linear, 16-bit linear and 8-bit -law or A-law sample formats. The sample rate is
8ksamples/s. The bit order may be little or big Endian. When 16-bit slots are used, the 3 or 8 unused
bits in each slot may be filled with sign extension, padded with zeros or a programmable 3-bit audio
attenuation compatible with some Motorola CODECs.
50
PCM_OUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Sign extension
8-bit sample
Figure 30: 16-bit slot with 8-bit companded sample and sign extension selected
PCM_OUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
8-bit sample
Zeros padding
Figure 31: 16-bit slot with 8-bit companded sample and zeros padding selected
PCM_OUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
3-bit sign
extension
13-bit sample
Figure 32: 16-bit slot with 13-bit linear sample and sign extension selected
PCM_OUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Audio gain
13-bit sample
Figure 33: 16-bit slot with 13-bit linear sample and audio gain selected
7.4.7 Additional Features
WT32 has a mute facility that forces PCM_OUT to be 0. In Master mode, PCM_SYNC may also be
forced to 0 while keeping PCM_CLK running, which some CODECS use to control power down.
7.4.8 PCM CLK and SYNC Generation
WT32 has two methods of generating PCM_CLK and PCM_SYNC in master mode. The first is
generating these signals by Direct Digital Synthesis (DDS) from BlueCore5 Multimedia External internal
4MHz clock. Using this mode limits PCM_CLK to 128, 256 or 512kHz and PCM_SYNC to 8kHz. The
second is generating PCM_CLK and PCM_SYNC by DDS from an internal 48MHz clock (which allows a
greater range of frequencies to be generated with low jitter, but consumes more power). The second
method is selected by setting bit 48M_PCM_CLK_GEN_EN in PSKEY_PCM_CONFIG32. When in this
mode and with long frame sync, the length of PCM_SYNC can be either 8 or 16 cycles of PCM_CLK,
determined by LONG_LENGTH_SYNC_EN in PSKEY_PCM_CONFIG32.
Equation 3 describes PCM_CLK frequency when being generated using the internal 48MHz clock:
Equation 3: PCM_CLK frequency when being generated using the internal 48 MHz clock
The frequency of PCM_SYNC relative to PCM_CLK can be set using Equation 4
Equation 4: PCM_SYNC frequency relative to PCM_CLK
CNT_RATE, CNT_LIMIT and SYNC_LIMIT are set using PSKEY_PCM_LOW_JITTER_CONFIG. As an
example, to generate PCM_CLK at 512kHz with PCM_SYNC at 8kHz, set
PSKEY_PCM_LOW_JITTER_CONFIG to 0x08080177.
51
7.4.9 PCM Configuration
The PCM configuration is set by using two PS Keys, PSKEY_PCM_CONFIG32 and
PSKEY_PCM_LOW_JITTER_CONFIG. The following tables detail these PS Keys. The default for
PSKEY_PCM_CONFIG32 key is 0x00800000, i.e. first slot following sync is active, 13-bit linear voice
format, long frame sync and interface master generating 256kHz PCM_CLK from 4MHz internal clock
with no tri-stating of PCM_OUT. PSKEY_PCM_LOW_JITTER_CONFIG is described in Table 23.
Name Bit position Description
- 0 Set to 0
SLAVE MODE EN 1
0 selects Master mode with internal generation of PCM_CLK and PCM_SYNC.
1 selects Slave mode requiring externally generated PCM_CLK and
PCM_SYNC. This should be set to 1 if 48M_PCM_CLK_GEN_EN (bit 11) is set.
SHORT SYNC EN 2
0 selects long frame sync (rising edge indicates start of frame), 1 selects
short frame sync (falling edge indicates start of frame).
- 3 Set to 0
SIGN EXTENDED EN 4
0 selects padding of 8 or 13-bit voice sample into a 16- bit slot by inserting
extra LSBs, 1 selects sign extension. When padding is selected with 13-bit
voice sample, the 3 padding bits are the audio gain setting; with 8-bit
samples the 8 padding bits are zeroes.
LSB FIRST EN 5 0 transmits and receives voice samples MSB first, 1 uses LSB first.
TX TRISTATE EN 6
0 drives PCM_OUT continuously, 1 tri-states PCM_OUT immediately after the
falling edge of PCM_CLK in the last bit of an active slot, assuming the next
slot is not active.
TX TRISTATE RISING
EDGE EN
7
0 tristates PCM_OUT immediately after the falling edge of PCM_CLK in the
last bit of an active slot, assuming the next slot is also not active. 1 tristates
PCM_OUT after the rising edge of PCM_CLK.
SYNC SUPPRESS EN 8
0 enables PCM_SYNC output when master, 1 suppresses PCM_SYNC whilst
keeping PCM_CLK running. Some CODECS utilize this to enter a low power
state.
GCI MODE EN 9 1 enables GCI mode.
MUTE EN 10 1 forces PCM_OUT to 0.
48M PCM CLK GEN EN 11
0 sets PCM_CLK and PCM_SYNC generation via DDS from internal 4 MHz
clock, as for BlueCore4-External. 1 sets PCM_CLK and PCM_SYNC generation
via DDS from internal 48 MHz clock.
LONG LENGTH SYNC EN 12
0 sets PCM_SYNC length to 8 PCM_CLK cycles and 1 sets length to 16
PCM_CLK cycles. Only applies for long frame sync and with
48M_PCM_CLK_GEN_EN set to 1.
- [20:13] Set to 0b00000000.
MASTER CLK RATE [22:21]
Selects 128 (0b01), 256 (0b00), 512 (0b10) kHz PCM_CLK frequency when
master and 48M_PCM_CLK_GEN_EN (bit 11) is low.
ACTIVE_SLOT [26:23] Default is 0001. Ignored by FW
SAMPLE_FORMAT [28:27]
Selects between 13 (0b00), 16 (0b01), 8(0b10) bit sample with 16-
cycle slot duration or 8 (0b11) bit sample with 8-cycle slot duration.
Table 22: PSKEY_PCM_CONFIG32 description
Name Bit position Description
CNT LIMIT [12:0] Sets PCM_CLK counter limit
CNT RATE [23:16] Sets PCM_CLK count rate.
SYNC LIMIT [31:24] Sets PCM_SYNC division relative to PCM_CLK.
Table 23: PSKEY_PCM_LOW_JITTER_CONFIG Description
Bluegiga Technologies Oy
Page 52 of 71
8 I/O Parallel Ports
The Parallel Input Output (PIO) Port is a general-purpose I/O interface to WT32. The port consists of eleven
programmable, bi-directional I/O lines, PIO[10:0]. Programmable I/O lines can be accessed either through an
embedded application running on WT32 or through private channel or manufacturer-specific HCI commands.
All PIO lines are configured as inputs with weak pull downs at reset.
PIO[2] / USB_PULL_UP (1)
The function depends on whether WT32 is a USB or UART capable version. On UART versions, this terminal
is a programmable I/O. On USB versions, it can drive a pull-up resistor on USB_D+. For applications using
external RAM, this terminal may be programmed for chip select.
PIO[3] / USB_WAKE_UP (1)
On UART versions of WT32, this terminal is a programmable I/O. On USB versions, its function is selected by
setting the Persistent Store Key PSKEY_USB_PIO_WAKEUP (0x2cf) either as a programmable I/O or as a
USB_WAKE_UP function.
PIO[4] / USB_ON (1)
On UART versions of WT32, this terminal is a programmable I/O. On USB versions, the USB_ON function is
also selectable.
PIO[5] / USB_DETACH (1)
On UART versions of WT32, this terminal is a programmable I/O. On USB versions, the USB_DETACH
function is also selectable.
PIO[6] / CLK_REQ
Function is determined by Persistent Store Keys. Using PSKEY_CLOCK_REQUEST_ENABLE, (0x246) this
terminal can be configured to be low when WT32 is in deep sleep and high when a clock is required. The
clock must be supplied within 4ms of the rising edge of PIO[6] to avoid losing timing accuracy in certain
Bluetooth operating modes.
PIO[7]
Programmable I/O terminal.
PIO[8]
Programmable I/O terminal.
PIO[9]
Programmable I/O terminal.
PIO[10]
Programmable I/O terminal.
Bluegiga Technologies Oy
Page 53 of 71
9 Software Stacks
WT32 is supplied with Bluetooth v2.0 + EDR compliant stack firmware, which runs on the internal RISC
microcontroller.
The WT32 software architecture allows Bluetooth processing and the application program to be shared in
different ways between the internal RISC microcontroller and an external host processor (if any). The upper
layers of the Bluetooth stack (above HCI) can be run either on-chip or on the host processor.
9.1 iWRAP Stack
PCM I/O
Host I/O
Radio
48kB RAM Baseband MCU
LC
LM
HCI
L2CAP
RFCOMM SDP
iWRAP
UART
Host I/O
PCM
Figure 34: iWRAP Stack
In Figure 34 above, the iWRAP software solution is described. In this version of the stack firmware shown, no
host processor is required to run the Bluetooth protocol stack. All software layers, including application
software, run on the internal RISC processor in a protected user software execution environment known as a
Virtual Machine (VM).
The host processor interfaces to iWRAP software through one or more of the physical interfaces, which are
also shown in the figure 35. The most common interfacing is done through the UART interface using the
ASCII commands supported by the iWRAP software. With these ASCII commands, the user can access
Bluetooth functionality without paying any attention to the complexity, which lies in the Bluetooth protocol
stack.
The user may write application code to run on the host processor to control iWRAP software by using ASCII
commands and to develop Bluetooth powered applications.
Bluegiga Technologies Oy
Page 54 of 71
Notes:
More details of iWRAP software and its features can be found from iWRAP User Guide,
which can be downloaded from www.bluegiga.com.
9.2 VM Stack
PCM I/O
Host I/O
Radio
48kB RAM Baseband MCU
LC
LM
HCI
L2CAP
RFCOMM SDP
VM Application Software
UART
USB
Host
I/O
PCM
Figure 35: WRAP THOR VM Stack
The version of the stack firmware shown in Figure 35 requires no host processor (but can use a host
processor for debugging etc.). All software layers, including application software, run on the internal RISC
processor in a protected user software execution environment known as a Virtual Machine (VM).
The user may write custom application code to run on the BlueCore VM using BlueLab™ software
development kit (SDK) supplied with the Casira development kit, available separately from Bluegiga or directly
form CSR. This code will then execute alongside the main WRAP THOR firmware. The user is able to make
calls to the WRAP THOR firmware for various operations. WRAP THOR firmware is not equal to iWRAP
firmware, which on the contrary does not allow users to run their own firmware in the module.
The execution environment is structured so that the user application does not adversely affect the main
software routines, thus ensuring that the Bluetooth stack software component does not need re-qualification
when the application is changed.
Using the VM and the BlueLab SDK, the user is able to develop applications such as a cordless headset or
other profiles without the requirement of a host controller. BlueLab is supplied with example code including a
full implementation of the headset profile.
Notes:
Bluegiga Technologies Oy
Page 55 of 71
Sample applications to control PIO lines can also be written with BlueLab SDK and the VM
for the HCI stack.
Software Development
WT32 Evaluation Kits are available to allow the evaluation of the WT32 hardware and software as well as a
CSR BlueLab toolkit for developing on-chip and host software.
Bluegiga Technologies Oy
Page 56 of 71
10 Enhanced Data Rate
EDR has been introduced to provide 2x and optionally 3x data rates with minimal disruption to higher layers of
the Bluetooth stack. CSR supports both of the new data rates, with WT32. WT32 is compliant with revision
v2.0.E.2 of the specification.
10.1 Enhanced Data Rate Baseband
At the baseband level, EDR uses the same 1.6kHz slot rate as basic data rate and therefore the packets can
be 1, 3, or 5 slots long as per the basic data rate. Where EDR differs from the basic data rate is that in the
same 1MHz symbol rate, 2 or 3 bits are used per symbol, compared to 1bit per symbol used by the basic data
rate. To achieve the increase in number of bits symbol, two new modulation schemes have been introduced
as summarized in Table 24 presented below and the modulation schemes are explained in the further
sections.
Scheme Bits per symbol Modulation
Basic data rate 1 GFSK
Enhanced data rate 2 P/4 DQPSK
Enhanced data rate 3 8DPSK (optional)
Table 24: Data rate schemes
Although the EDR uses new packets, link establishment and management are unchanged and still use Basic
Rate packets.
10.2 Enhanced Data Rate ∏/4 DQPSK
4-state Differential Phase Shift Keying
2 bits determine phase shift between consecutive symbols
2 bits determine phase shift between consecutive symbols
/4 rotation avoids phase shift of
, which would cause large amplitude variation
Raised Cosine pulse shaping filter to further reduce side band emissions
Bit pattern Phase shift
00

01

10

11 
Table 25: 2 bits determine phase shift between consecutive symbols
Bluegiga Technologies Oy
Page 57 of 71
10.3 8DQPSK
8-state Differential Phase-Shift Keying
Three bits determine phase shift between consecutive symbols.
Bit pattern Phase shift

 
 
 

 
 
 
Table 26: 3 bits determine phase shift between consecutive symbols
Figure 36: 8DQPSK
Bluegiga Technologies Oy
Page 58 of 71
11 Layout and Soldering Considerations
11.1 Soldering Recommendations
WT32 is compatible with industrial standard reflow profile for Pb-free solders. The reflow profile used is
dependent on the thermal mass of the entire populated PCB, heat transfer efficiency of the oven and
particular type of solder paste used. Consult the datasheet of particular solder paste for profile configurations.
Bluegiga Technologies will give following recommendations for soldering the module to ensure reliable solder
joint and operation of the module after soldering. Since the profile used is process and layout dependent, the
optimum profile should be studied case by case. Thus following recommendation should be taken as a
starting point guide.
o Refer to technical documentations of particular solder paste for profile configurations
o Avoid using more than one flow.
o Reliability of the solder joint and self-alignment of the component are dependent on the
solder volume. Minimum of 150m stencil thickness is recommended.
o Aperture size of the stencil should be 1:1 with the pad size.
A low residue, “no clean” solder paste should be used due to low mounted height of the component
11.2 Layout Guidelines
11.2.1 Audio Layout
Route audio lines as differential pairs. The positive and negative signals should run parallel and close to each
other until they are converted to single-ended signals. Use dedicated audio ground plane for entire audio
section.
11.2.2 Antenna Design
Do not place GND plane or any metal directly under the chip antenna of WT32. To avoid any excess parasitic
capacitance in the antenna feed line caused by the RF test pin on the bottom side of the module, the area
underneath the RF test pin should also be left free from copper. The chip antenna of WT32 requires GND
planes as shown in the Figure 37. The module should not be placed closer than 7 mm from a PCB corner and
the module should be placed to an edge of the PCB. Any metal in close proximity of the antenna will have an
effect on the antenna performance. Thus any metal should be placed as far from the antenna as possible. The
antenna of WT32 is high dielectric chip antenna and any surrounding dielectric material has only minor effect
(< 20 MHz) on the resonant frequency.
Avoid placing vias or any bare copper under the module. Since the module has several vias on the bottom
side, any via or bare copper under the module can cause a short circuit. Vias under the module are shown in
the Figure 38.
Bluegiga Technologies Oy
Page 59 of 71
Figure 37: Recommended layout for the ground planes around the module.
Figure 38: Bottom side layout of the module. Any via in the module can cause a short if placed directly
above bare copper on a PCB.
Bluegiga Technologies Oy
Page 60 of 71
12 WT32 Physical Dimensions
Figure 39: Recommended PCB land pattern for WT32-A and WT32-E
Figure 40: WT32 viewed from the top
Bluegiga Technologies Oy
Page 61 of 71
23.9 mm (+/- 0.15mm)
2.5 mm
(+/- 0.1mm) 2.2 mm
(+/- 0.1mm)
17.9 mm (+/- 0.15mm)
15.9 mm
(+/- 0.1mm)
3.7 mm
(+/- 0.1mm)
8.5 mm
(+/- 0.1mm)
3.7 mm
(+/- 0.1mm)
Figure 41: WT32 physical dimensions
Bluegiga Technologies Oy
Page 62 of 71
13 Package
Figure 42: Carrier tape appearance and dimensions
Bluegiga Technologies Oy
Page 63 of 71
Figure 43: Reel appearance and dimensions
Bluegiga Technologies Oy
Page 64 of 71
14 Certifications
WT32 is compliant to the following specifications.
14.1 Bluetooth
WT32 module is Bluetooth qualified and listed as an end product. If not modified in any way, it is a complete
Bluetooth entity, containing software and hardware functionality as well as the whole RF-part including the
antenna. This practically translates to that if the module is used without modification of any kind, it does not
need any Bluetooth approval work. If changes are made in the parameter set, added profiles or in the antenna
design, it is required to be submitted to a BQB (Bluetooth Qualification Body) for evaluation on what needs to
be tested.
With HCI firmware WT32 will not meet the requirements of end product qualification.
WT32 is Bluetooth compliant to the following specifications
RF as defined in Part A of the Bluetooth specification v2.0+EDR, Vol.2 Core System Package [Controller
volume] (Class 1 operation) with all optional and mandatory features supported.
BB as defined in Part B of the Bluetooth specification v2.0+EDR, Vol.2 Core System Package [Controller
volume], and specified in the covered functionality of the Software Integrated Component (Bluetooth ID:
B012319)
LM as defined in Part C of the Bluetooth specification v2.0+EDR, Vol.2 Core System Package [Controller
volume], and specified in the covered functionality of the Software Integrated Component (Bluetooth ID:
B012319)
L2CAP as defined in Part A of the Bluetooth specification v2.0+EDR, Vol.3 Core System Package [Controller
volume], and specified in the covered functionality of the Software Integrated Component (Bluetooth ID:
B012319)
SDP as defined in Part B of the Bluetooth specification v2.0+EDR, Vol.3 Core System Package [Controller
volume], and specified in the covered functionality of the Software Integrated Component (Bluetooth ID:
B012319)
RFCOMM as defined in PART F:1 of the Bluetooth Core Specification v1.1 and specified in the covered
functionality of the Software Integrated Component (Bluetooth ID: B012319).
Generic Access GAP as defined in PART C of the Bluetooth Core Specification v2.0+EDR, Vol.3 Core
Systems Package [Host Volume], and specified in the covered functionality of the Software Integrated
Component (Bluetooth ID: B012319).
Serial Port Profile (SPP) as defined in PART K:5 of the Bluetooth Profile Specification v1.1, and specified in
the covered functionality of the Software Integrated Component (Bluetooth ID: B012319).
Bluetooth EPL: https://www.bluetooth.org/tpg/EPL_Detail.cfm?ProductID=6102
Bluetooth QDID: B014372
Bluegiga Technologies Oy
Page 65 of 71
14.2 FCC
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part responsible for
compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
This device may not cause interference and
This device must accept any interference, including interference that may cause undesired operation
of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.
Note: The end product shall has the words “Contains Transmitter Module FCC ID: QOQWT32AE
WT32-A/EC ID: QOQWT32AE
Bluegiga Technologies Oy
Page 66 of 71
14.3 CE
WT32 meets the requirements of the standards below and hence fulfills the requirements of EMC Directive
89/336/EEC as amended by Directives 92/31/EEC and 93/68/EEC within CE marking requirement.
Electromagnetic emission EN 301 489-17 V.1.2.1
o EN 55022:1998+A
o EN 55022:2000+A3
o EN 55022:2003 Class B
o EN 61000-3-2:2001
o EN 61000-3-3:1995 A1:2001
o EN 61000-4-3:2002
o EN 61000-4-4:1995 A1:2000
o EN 61000-4-5:1995 A1:2000
o EN 61000-4-6:1996 A1:2000
o EN 61000-4-11:1994 A1:2000
ETSI EN 300.328 V1.6.1:2004
14.4 Industry Canada (IC)
WT32 meets Industry Canada’s procedural and specification requirements for certification.
Industry Canada ID: 5123A-BGTWT32AE
Bluegiga Technologies Oy
Page 67 of 71
14.5 MIC Japan
WT32 has type approval for Japan with certification ID R 209- J00052
Bluegiga Technologies Oy
Page 68 of 71
14.6 Pretested antennas
Bluegiga Technologies Oy
Page 69 of 71
Bluegiga Technologies Oy
Page 70 of 71
15 RoHS Statement with a List of Banned Materials
WT32 meets the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the
Restriction of Hazardous Substance (RoHS)
The following banned substances are not present in WT32, which is compliant with RoHS:
Cadmium
Lead
Mercury
Hexavalent chromium
PBB (Polybrominated Bi-Phenyl)
PBDE (Polybrominated Diphenyl Ether)
Bluegiga Technologies Oy
Page 71 of 71
16 Contact Information
Sales: sales@bluegiga.com
Technical support: support@bluegiga.com
http://techforum.bluegiga.com
Orders: orders@bluegiga.com
WWW: www.bluegiga.com
www.bluegiga.hk
Head Office / Finland:
Phone: +358-9-4355 060
Fax: +358-9-4355 0660
Sinikalliontie 5A
02630 ESPOO
FINLAND
Postal address / Finland:
P.O. BOX 120
02631 ESPOO
FINLAND
Sales Office / USA:
Phone: +1 770 291 2181
Fax: +1 770 291 2183
Bluegiga Technologies, Inc.
3235 Satellite Boulevard, Building 400, Suite 300
Duluth, GA, 30096, USA
Sales Office / Hong-Kong:
Phone: +852 3972 2186
Bluegiga Technologies Ltd.
Unit 10-18
32/F, Tower 1, Millennium City 1
388 Kwun Tong Road
Kwun Tong, Kowloon
Hong Kong
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Bluegiga Technologies:
WT32-A-AI4 WT32-E-AI4 WT32-A-AI3 WT32-E-AI3 WT32-A-AI5 WT32-A-AI5S-APTX WT32-E-AI5-APTX WT32-
A-AI5S WT32-E-AI5 WT32-A-AI5-APTX WT32-E-AI5S-APTX WT32-E-AI5S