DS26LS32AC,DS26LS32C,DS26LS32M,DS26LS33M
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M Quad Differential Line Receivers
Literature Number: SNLS352B
Obsolete Device: DS26LS33M
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
Quad Differential Line Receivers
General Description
The DS26LS32 and DS26LS32A are quad differential line
receivers designed to meet the RS-422, RS-423 and Federal
Standards 1020 and 1030 for balanced and unbalanced
digital data transmission.
The DS26LS32 and DS26LS32A have an input sensitivity of
200 mV over the input voltage range of ±7V and the
DS26LS33 have an input sensitivity of 500 mV over the input
voltage range of ±15V.
The DS26LS32A differ in function from the popular
DS26LS32 and DS26LS33 in that input pull-up and pull-
down resistors are included which prevent output oscillation
on unused channels.
Each version provides an enable and disable function com-
mon to all four receivers and features TRI-STATE ®outputs
with 8 mA sink capability. Constructed using low power
Schottky processing, these devices are available over the
full military and commerical operating temperature ranges.
Features
nHigh differential or common-mode input voltage ranges
of ±7V on the DS26LS32 and DS26LS32A and ±15V
on the DS26LS33
n±0.2V sensitivity over the input voltage range on the
DS26LS32 and DS26LS32A, ±0.5V sensitivity on the
DS26LS33
nDS26LS32 and DS26LS32A meet all requirements of
RS-422 and RS-423
n6k minimum input impedance
n100 mV input hysteresis on the DS26LS32 and
DS26LS32A, 200 mV on the DS26LS33
nOperation from a single 5V supply
nTRI-STATE outputs, with choice of complementary
output enables for receiving directly onto a data bus
Logic Diagram
00525501
TRI-STATE®is a registered trademark of National Semiconductor Corporation.
May 1999
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M Quad Differential Line Receivers
© 2004 National Semiconductor Corporation DS005255 www.national.com
Obsolete Device: DS26LS33M
Connection Diagrams
Dual-In-Line Package 20-Lead Ceramic Leadless Chip Carrier
00525502
Top View
Order Number DS26LS32CM, DS26LS32CN,
DS26LS32ACM, DS26LS32ACN, DS26LS33ACM
or DS26LS33ACN
See NS Package Number M16A or N16E
For Complete Military Product Specifications,
refer to the appropriate SMD or MDS.
Order Number DS26LS32MJ/883, DS26LS32MW/883,
DS26LS32ME/883, DS26LS33MW/883
See NS Package Number E20A, J16A or W16A
00525512
Truth Table
ENABLE ENABLE Input Output
0 1 X Hi-Z
See V
ID
≥V
TH
(Max) 1
Note Below V
ID
≤V
TH
(Min) 0
Hi-Z = TRI-STATE®
Note: Input conditions may be any combination not defined for ENABLE and ENABLE .
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com 2
Obsolete Device: DS26LS33M
Absolute Maximum Ratings (Note 3)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage 7V
Common-Mode Range ±25V
Differential Input Voltage ±25V
Enable Voltage 7V
Output Sink Current 50 mA
Maximum Power Dissipation (Note 1) at 25˚C
Cavity Package 1433 mW
Molded Dip Package 1362 mW
SO Package DS26LS32 1002 mW
DS26LS32A 1051 mW
Storage Temperature Range −65˚C to
+165˚C
Lead Temperature (Soldering, 4
seconds) 260˚C
Operating Conditions
Min Max Units
Supply Voltage, (V
CC
)
DS26LS32M, DS26LS33M 4.5 5.5 V
(MIL)
DS26LS32C 4.75 5.25 V
DS26LS32AC
(COML)
Temperature, (T
A
)
DS26LS32M, DS26LS33M −55 +125 ˚C
(MIL)
DS26LS32C 0 +70 ˚C
DS26LS32AC
(COML)
Note 1: Derate cavity package 9.6 mW/˚C above 25˚C; derate molded DIP
package 10.9 mW/˚C above 25˚C.
Note 2: Derate SO Package 8.01 mW/˚C for DS26LS32
8.41 mW/˚C for DS26LS32A
Electrical Characteristics (Notes 4, 5, 6)
over the operating temperature range unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
V
TH
Differential Input V
OUT
=V
OH
DS26LS32, DS26LS32A, −7V ≤V
CM
≤+7V −0.2 ±0.07 0.2 V
Voltage or V
OL
DS26LS33, DS26LS33A, −15V ≤V
CM
+15V −0.5 ±0.14 0.5 V
R
IN
Input Resistance −15V ≤V
CM
≤+15V (One Input AC GND) 6.0 8.5 kΩ
I
IN
Input Current (Under V
IN
= 15V, Other Input −15V ≤V
IN
≤+15V 2.3 mA
Test) V
IN
= −15V, Other Input −15V ≤V
IN
≤+15V −2.8 mA
V
OH
Output High Voltage V
CC
= MIN, ∆V
IN
= 1V, Commercial 2.7 4.2 V
V
ENABLE
= 0.8V, I
OH
= −440 µA Military 2.5 4.2 V
V
OL
Output Low Voltage V
CC
= Min, ∆V
IN
= −1V, I
OL
= 4 mA 0.4 V
V
ENABLE
= 0.8V I
OL
= 8 mA 0.45 V
V
IL
Enable Low Voltage 0.8 V
V
IH
Enable High Voltage 2.0 V
V
I
Enable Clamp V
CC
= Min, I
IN
= −18 mA −1.5 V
Voltage
I
O
OFF-State (High V
CC
= Max V
O
= 2.4V 20 µA
Impedance) Output V
O
= 0.4V −20 µA
Current
I
IL
Enable Low Current V
IN
= 0.4V −0.36 mA
I
IH
Enable High Current V
IN
= 2.7V 20 µA
I
SC
Output Short-Circuit V
O
= 0V, V
CC
= Max, ∆V
IN
= 1V −15 −85 mA
Current
I
CC
Power Supply V
CC
= Max, All V
IN
= GND, DS26LS32, DS26LS32A 52 70 mA
Current Outputs Disabled DS26LS33, DS26LS33A 57 80 mA
I
I
Input High Current V
IN
= 5.5V 100 µA
V
HYST
Input Hysteresis T
A
= 25˚C, V
CC
= 5V, DS26LS32, DS26S32A 100 mV
V
CM
= 0V DS26LS33, DS26LS33A 200 mV
Note 3: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The table of “Electrical Characteristics” provides conditions for actual device operation.
Note 4: All currents into device pins are shown as positive, all currents out of device pins are shown as negative, all voltages are referenced to ground, unless
otherwise specified. All values shown as max or min are so classified on absolute value basis.
Note 5: All typical values are VCC =5V,T
A= 25˚C.
Note 6: Only one output at a time should be shorted.
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com3
Obsolete Device: DS26LS33M
Switching Characteristics
V
CC
= 5V, T
A
= 25˚C
Symbol Parameter Conditions DS26LS32/DS26LS33 DS26LS32A/DS26LS33A Units
Min Typ Max Min Typ Max
t
PLH
Input to Output C
L
=15pF 17 25 23 35 ns
t
PHL
17 25 23 35 ns
t
LZ
ENABLE to Output C
L
=5pF 2030 1530ns
t
HZ
15 22 20 25 ns
t
ZL
ENABLE to Output C
L
=15pF 15 22 14 22 ns
t
ZH
15 22 15 22 ns
AC Test Circuit and Switching Time Waveforms
Load Test Circuit for TRI-STATE®Outputs
00525503
Propagation Delay (Notes 7, 9)
00525504
Enable and Disable Times (Notes 8, 9)
00525505
Note 7: Diagram shown for ENABLE low.
Note 8: S1 and S2 of load circuit are closed except where shown.
Note 9: Pulse generator for all pulses: Rate = 1.0 MHz; ZO=50Ω;t
r≤6 ns; tf≤6.0 ns.
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com 4
Obsolete Device: DS26LS33M
Typical Applications
Two-Wire Balanced Interface — RS-422
00525506
Single Wire with Driver Ground Reference — RS-423
00525507
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com5
Obsolete Device: DS26LS33M
Physical Dimensions inches (millimeters)
unless otherwise noted
Ceramic Dual-In-Line Package (J)
Order Number DS26LS32MJ/883 or DS26LS33MJ/883
NS Package Number J16A
Small Outline Package (M)
Order Number DS26LS32CM or DS26LS32ACM
NS Package Number M16A
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com 6
Obsolete Device: DS26LS33M
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number DS26LS32CN or DS26LS32ACN
NS Package Number N16E
16 Lead Ceramic Flatpak (W)
Order Number DS26LS32MW/883 or DS26LS33MW/883
NS Package Number W16A
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M
www.national.com7
Obsolete Device: DS26LS33M
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
20 Lead Ceramic Leadless Chip Carrier (E)
Order Number DS26LS32ME/883
NS Package Number E20A
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification
(CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
National Semiconductor
Americas Customer
Support Center
Email: new.feedback@nsc.com
Tel: 1-800-272-9959
National Semiconductor
Europe Customer Support Center
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor
Asia Pacific Customer
Support Center
Email: ap.support@nsc.com
National Semiconductor
Japan Customer Support Center
Fax: 81-3-5639-7507
Email: jpn.feedback@nsc.com
Tel: 81-3-5639-7560
www.national.com
DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M Quad Differential Line Receivers
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Obsolete Device: DS26LS33M
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic."Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP®Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright ©2012, Texas Instruments Incorporated
