UL865 Product Description 80420ST10586A Rev.4 - 2017-06-01 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 APPLICABILITY TABLE PRODUCT UL865-EUR UL865-EUD UL865-NAR UL865-NAD UL865-N3G Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 2 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Disclaimer The information contained in this document is the proprietary information of Telit Communications S.p.A. and its affiliates ("TELIT"). The contents are confidential and any disclosure to persons other than the officers, employees, agents or subcontractors of the owner or licensee of this document, without the prior written consent of Telit, is strictly prohibited. Telit makes every effort to ensure the quality of the information it makes available. Notwithstanding the foregoing, Telit does not make any warranty as to the information contained herein, and does not accept any liability for any injury, loss or damage of any kind incurred by use of or reliance upon the information. Telit disclaims any and all responsibility for of the devices characterized in this document, the application of the device must comply with standards of the applicable country, and where with the relevant wiring rules. the application and notes that the safety applicable, Telit reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to programs and/or equipment at any time and without notice. Such changes will, nevertheless be incorporated into new editions of this document. Copyright: Transmittal, reproduction, dissemination and/or editing of this document as well as utilization of its contents and communication thereof to others without express authorization are prohibited. Offenders will be held liable for payment of damages. All rights are reserved. Copyright (c) Telit Communications S.p.A. 2013. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 3 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Contents 1. Introduction ................................................. 6 1.1. Scope ..................................................... 6 1.2. Audience .................................................. 6 1.3. Contact Information, Support .............................. 6 1.4. Text Conventions .......................................... 7 1.5. Related Documents ......................................... 7 1.6. Document History .......................................... 7 2. Overview ..................................................... 8 2.1. Product variants .......................................... 9 2.2. Target Market ............................................. 9 2.3. Features .................................................. 9 2.4. Approvals ................................................ 12 3. General Product Description ................................. 13 3.1. Dimensions and 2D mechanical drawing ..................... 13 3.2. Environmental requirements ............................... 14 3.2.1. 3.2.2. Temperature range .......................................... 14 RoHS compliance ............................................ 14 3.3. Operating Frequency ...................................... 15 3.4. Transmitter output power ................................. 16 3.5. Supply voltage ........................................... 16 3.6. Power consumption ........................................ 17 3.7. Logic level .............................................. 17 3.8. Input and Outputs ........................................ 17 3.8.1. 3.8.2. 3.8.3. 3.8.4. 3.8.5. 3.8.6. 3.8.7. 3.8.8. 3.8.9. 3.8.10. General Purpose I/Os ....................................... Power on monitor (PWR_MON) ................................. Power on/off control (ON_OFF) .............................. Auxiliary power output for accessory (VAUX) ................ SIM Reader ................................................. Converters ................................................. Audio Interface ............................................ Serial ports ............................................... USB port ................................................... User Interface ........................................... Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 4 of 33 17 17 18 18 18 18 18 18 18 18 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.9. Features ................................................. 18 3.9.1. 3.9.2. 3.9.3. 3.9.4. 3.9.5. 3.9.6. 3.9.7. 3.9.8. 3.9.9. 3.9.10. 3.9.11. 3.9.12. Speech Coding .............................................. SMS ........................................................ RTC Bypass out ............................................. Data Transmission capabilities ............................. Local security management .................................. Call control ............................................... Phonebook .................................................. Characters management ...................................... SIM related functions ...................................... Call status indication ................................... Automatic answer ......................................... Supplementary services ................................... 18 19 19 19 19 19 19 20 20 20 20 20 3.10. Mounting the modules on your board ..................... 20 3.11. Packing system ......................................... 21 4. Evaluation Kit .............................................. 22 5. AT Commands ................................................. 23 6. Safety Recommendations ...................................... 24 7. Conformity assessment issues ................................ 26 7.1. RTT&E Notified Body statement of Opinion ................. 28 7.2. FCC certificate .......................................... 29 7.3. IC certificates .......................................... 31 8. List of acronyms ............................................ 32 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 5 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 1. 1.1. Introduction Scope Scope of this document is to give an overview of the Telit UL865 module, which can support GSM/GPRS/EDGE and WCDMA/HSPA with data/voice capabilities. 1.2. Audience This document is intended for customers who are evaluating the UL865 product. 1.3. Contact Information, Support For general contact, technical documentation errors and to order Technical Support Center (TTSC) at: support, to report manuals, contact Telit TS-EMEA@telit.com TS-NORTHAMERICA@telit.com TS-LATINAMERICA@telit.com TS-APAC@telit.com Alternatively, use: http://www.telit.com/en/products/technical-supportcenter/contact.php For detailed information about where you can buy the Telit modules or for recommendations on accessories and components visit: http://www.telit.com To register for product news and announcements or for product questions contact Telit Technical Support Center (TTSC). Our aim is to make this guide as helpful as possible. Keep us informed of your comments and suggestions for improvements. Telit appreciates feedback from the users of our information. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 6 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 1.4. Text Conventions Danger - This information MUST be followed or catastrophic equipment failure or bodily injury may occur. Caution or Warning - Alerts the user to important points about integrating the module, if these points are not followed, the module and end user equipment may fail or malfunction. Tip or Information - Provides advice and suggestions that may be useful when integrating the module. All dates are in ISO 8601 format, i.e. YYYY-MM-DD. 1.5. 1.6. Related Documents UL865 Hardware User Guide, 1VV0301050 Telit EVK2 User Guide, 1vv0300704 Document History Revision Date 0 2013-02-04 1 2014-01-07 2 3 4 2014-04-28 2017-03-01 2017-06-01 Changes First issue Updated Ch. 2.1, 3.2. Added certifications in Ch.7 Layout of table at Ch.2.1. Ch.2.3 Updated certificates for new SW release Updated RED certificates Updated SAFETY RECOMMENDATIONS Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 7 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 2. Overview The UL865 Series further enriches the xL865 Family with a number of UMTS/HSPA variants targeted at European (EMEA) and North American (NA) markets. The dual-band UMTS/HSPA, dual-band GSM/GPRS engine in the UL865 Series is voice-capable supporting digital (DVI) interface. It delivers UMTS/HSPA 3GPP Release 7 compliant data communications and is equipped with a high-speed USB 2.0 port, eight I/O ports, two A/D and one D/A converters. For streamlined application development and system integration the company offers RIL drivers for all major operating systems. The UL865 features a VQFN packaging that is fully pad-level compatible with its 2G companion, the GL865-DUAL V3. As a part of Telit's corporate policy of environmental protection, all Telit products comply with the RoHS (Restriction of Hazardous Substances) directive of the European Union (EU Directive 2011/65/EU) NOTE: Some of the performances of the Telit modules depend on S/W version installed on the module itself. The Telit modules S/W group is continuously working in order to add new features and improve the overall performances. The Telit modules are easily upgraded by the developer using the Telit Flash Programmer. NOTE: In order to meet the competitive OEM and vertical market stringent requirements, Telit supports its customers with a dedicated Support Policy with: Telit Evaluation Kit EVK2 to help you to develop your application; A website with all updated information available; An high level specialist technical support to assist you in your development; Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 8 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 2.1. Product variants The following table describes the variants of UL865 series, available for both EUx and NAx configurations as dual band in 2G&3G, plus an additional 3G-only variant for the North American Market. 2.2. Variants Freq. Bands 2G (MHz) Freq. Bands 3G (MHz) Features UL865-EUR 900/1800 900/2100 Data&Voice UL865-EUD 900/1800 900/2100 Data-only UL865-NAR 850/1900 850/1900 Data&Voice UL865-NAD 850/1900 850/1900 Data-only UL865-N3G N.A. 850/1900 Data&Voice Target Market The UL865 is designed and developed for applications such as: 2.3. Point-of-Sales (POS) terminals mHealth Monitoring Security alarms with cameras Battery powered devices Telemetry Telematics, including Mapping and Infotainment Handheld scanners and logistics devices Features Advanced E-GPRS/WCDMA/HSDPA/HSUPA Software protocol stack (Layer 1 to 3) - Version: 3GPP Release 7 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 9 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 GSM Quad band (900/1800 MHz for EUx, 850/1900 MHz for NAx) WCDMA dual-band: the NAx models HSDPA up 7.2Mbps HSUPA up to 5.76Mbps WCDMA up to 384kbps downlink/uplink DTM (Dual Transfer Mode) CPC (DRX/DTX) (Continuous Packet Connectivity) DARP Control via AT commands according to 3GPP TS27.005, 27.007 and Telit customized AT commands Serial port multiplexer 3GPP TS27.010 SIM application Tool Kits 3GPP TS 51.014 Power consumption (typical values) B1&B8 for the EUx models and B2&B5 for - Stand-by current 2G, DRX9, 1.2 mA - Stand-by current 3G, DRX7, 1.8 mA Output power - Class 4 (2W) @ 850 / 900 MHz, GSM - Class 1 (1W) @ 1800 / 1900 MHz, GSM - Class E2 (0.5W) @ 850/900 MHz, EDGE - Class E2 (0.4W) @ 1800/1900 MHz, EDGE - Class 3 (0.25W) @ 850/900/1900/2100 MHz, WCDMA Interfaces I/O ports including multi-functional I/Os I2S for digital audio interface USB 2.0 HS 1 UART 1 Auxiliary serial port (RX/TX only) 1 I2C 1.8V/3V SIM interface Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 10 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Audio Telephony, emergency call HR, FR, EFR, AMR for GSM and AMR for WCDMA voice codec Spatial Noise Suppression Multiple audio profiles pre-programmed and fully configurable DTMF SMS Point to point mobile originated and mobile terminated SMS Concatenated SMS supported SMS cell broadcast Text and PDU mode SMS over GPRS Data transmission HSPA: category 8 in downlink e category 6 in uplink DL up to 7.2Mbps UL up to 5.76Mbps WCDMA: up to 384kbps downlink/uplink Asynchronous non-transparent CSD up to 9.6kbps GPRS class 10 for NAx variants and class 33 for EUx variants EDGE class 10 for NAx variants and class 33 for EUx variants Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1 to 9 (EDGE) GSM Supplementary Services Call forwarding Call barring Call waiting & call hold Advice of charge Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 11 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Calling line identification presentation [CLIP] Calling line identification restriction [CLIR] Unstructured supplementary services mobile originated data [USSD] Closed user group Additional features 2.4. SIM phonebook Fixed Dialling Number (FDN) Call control & status indication SIM phonebook Character management (IRA, UCS2, GSM) USIM 3GPP Rel.7 Real Time Clock Automatic answer Alarm management Embedded TCP/IP stack, including TCP, IP, UDP, and FTP protocols CSD for Video Telephony support Approvals Fully type approved confirming with R&TTE directive CE, GCF FCC, IC, PTCRB AT&T RoHS and REACH (all variants) Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 12 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3. 3.1. General Product Description Dimensions and 2D mechanical drawing UL865 has a QFN package, with 48 pads. The overall dimensions of UL865 are: Length: 24.4 mm Width: 24.4mm Thickness: 2.6 mm Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 13 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.2. Environmental requirements 3.2.1. Temperature range Operating Temperature Range -40C ~ +85C 3.2.2. RoHS compliance As a part of Telit corporate policy of environmental protection, the UL865 complies with the RoHS (Restriction of Hazardous Substances) directive of the European Union (EU directive 2011/65/EU). REACH compliant as well. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 14 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.3. Operating Frequency The operating frequencies in GSM850, EGSM900, DCS1800, PCS1900, WCDMA modes are compliant to the 3GPP and WCDMA specifications. Mode GSM850 Freq. (MHz) 824.2 ~ 848.8 TX Freq. RX (MHz) 869.2 ~ 893.8 Channels TX - RX offset 128 ~ 251 45 MHz 890.0 ~ 914.8 935.0 ~ 959.8 0 ~ 124 45 MHz 880.2 ~ 889.8 925.2 ~ 934.8 975 ~ 1023 45 MHz 1710.2 ~ 1784.8 1805.2 ~ 1879.8 512 ~ 885 95MHz 1850.2 ~ 1909.8 1930.2 ~ 1989.8 512 ~ 810 80MHz EGSM900 DCS1800 PCS1900 WCDMA850 (band V) WCDMA900 (band VIII) WCDMA1900 (band II) WCDMA2100 (Band I) 826.4 ~ 846.6 882.4 ~ 912.6 1852.4 ~ 1907.6 1922.4 ~ 1977.6 871.4 ~ 891.6 927.4 ~ 957.6 1932.4 ~ 1987.6 2112.4 ~ 2167.6 Tx: 4132 ~ 4233 Rx: 4357 ~ 4458 Tx: 2712 ~ 2863 Rx: 2937 ~ 3088 Tx: 9262 ~ 9538 Rx: 9662 ~ 9938 Tx: 9612 ~ 9888 Rx: 10562 ~ 10838 45MHz 45MHz 80MHz 190MHz Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 15 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.4. Transmitter output power The UL865 transceiver output of GSM/GPRS mode in 850/900MHz bands are class 4 in accordance with the specifications which determine the nominal 2W peak RF power (+33dBm) on 50ohm. In the 1800/1900MHz bands are class 1 in accordance with the specification which determines the nominal 1W peak RF power (+30dBm) on 50ohm. The UL865 transceiver output of EDGE mode in 850/900MHz bands are class E2 in accordance with the specifications which determine the nominal 0.5W peak RF power (+27dBm) on 50ohm. In the 1800/1900MHz bands are class E2 in accordance with the specification which determine the nominal 0.4W peak RF power (+26dBm) on 50ohm. The UL865 transceiver output of WCDMA mode in 850/900/1900/2100MHz bands is class 3 in accordance with the specifications which determine the nominal 0.25W peak RF power (+24dBm) on 50ohm. 3.5. Supply voltage The external power supply must be connected to VBATT signal and must fulfill the following requirements: Nominal Supply Voltage 3.8V Operating Voltage Range 3.4 ~ 4.2V Extended Operating Voltage Range 3.22 ~ 4.5V CAUTION: The operating voltage MUST not be exceeded; Special care must be taken when designing the application's power supply section to avoid an excessive voltage drop. If the voltage drop is exceeding the limits it could cause a Power Off of the module. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 16 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.6. Power consumption The UL865 power consumptions are described in the following table Depending on network configuration and not under module control 3.7. Logic level Where not specifically stated, the most of interface circuits work at 1.8V CMOS logic levels. To get more detailed information about the logic level specifications used for UL865, please refer to the Hardware User Guide. 3.8. 3.8.1. Input and Outputs General Purpose I/Os Pins of general purpose I/Os can be configured by AT command in three different ways as input, output and alternative function. 3.8.2. Power on monitor (PWR_MON) The PWR_MON indicates the status of the module running properly. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 17 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.8.3. Power on/off control (ON_OFF) External power on/off control input. Refer to the Hardware User Guide for more details of Power on timing. 3.8.4. Auxiliary power output for accessory (VAUX) A regulated 1.8V power output is provided for an external device. 3.8.5. SIM Reader The UL865 family supports 1 SIM/USIM at 1.8V and 3V ONLY with and external SIM connector. For 5V SIM, an external level translator can be added. Refer to the UL865 Hardware User Guide. 3.8.6. Converters The UL865 family has 2 ADC and 1DAC. 3.8.7. Audio Interface A Digital Audio bus is available. 3.8.8. Serial ports Two serial ports are available. Full RS232-C Auxiliary serial port (RX/TX only) 3.8.9. USB port The USB2.0 High Speed has a clock rate of 480MHz 3.8.10. User Interface The user interface is managed by AT commands according to ITU-T V.250, 3GPP 27.007 and 27.005 specifications. Please refer to the AT command User Guide for complete details. 3.9. Features 3.9.1. Speech Coding The UL865 support the following voice codecs: Adaptive Multi Rate for WCDMA Half Rate, Full Rate, Enhanced Full Rate, Adaptive Multi Rate for GSM Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 18 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.9.2. SMS The UL865 supports the following SMS types: Mobile Terminated (MT) class 0 ~ 3 with signaling of new incoming SMS, SIM full, SMS read Mobile Originated class (MO) 0 ~ 3 with writing, saving in SIM and sending Cell broadcast compatible with CB DRX signaling of new incoming SMS. The module supports also SMS over GPRS 3.9.3. RTC Bypass out The VRTC pin brings out the Real Time Clock supply, which is separate from the rest of the digital part, allowing having only RTC going on when all the other parts of the device are off. To this power output a backup capacitor can be added in order to increase the RTC autonomy during power off of the battery. NO Devices must be powered from this pin. 3.9.4. Data Transmission capabilities The UL865 supports: HSPA: D/L up to 7.2Mbps, U/L up to 5.76Mbps Asynchronous non-transparent CSD up to 9.6kbps for GSM, 14.4kbps for WCDMA EDGE Class 10 for NAx variants and Class 33 for EUx variants Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1 to 9 (EDGE) 3.9.5. Local security management The local security management can be done with the lock of Universal Subscriber Identity Module (USIM), and the security code will be requested at power-up. 3.9.6. Call control The calling cost control function is supported. 3.9.7. Phonebook This function allows storing the telephone numbers into SIM memory. The capability depends on the SIM version and its embedded memory. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 19 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.9.8. Characters management The UL865 supports the IRA, GSM, PCCP437, 8859-1 and UCS2 character sets, EXT and PDU mode. 3.9.9. SIM related functions Activation and deactivation of the numbers stored in phone book FDN (Fixed Dialing Numbers), ADN (Abbreviated Dialing Number) and PIN insertion are supported. Extension at the PIN2 for the PUK2 insertion capability for lock condition is supported too. 3.9.10. Call status indication The call status indication is supported. 3.9.11. Automatic answer The automatic answering feature is supported. The user/application can specify the number of rings after which the module will make an answer automatically. 3.9.12. Supplementary services The following supplementary services are supported: Call Barring Call Forwarding Calling Line Identification Presentation (CLIP) Calling Line Identification Restriction (CLIR) Call Waiting, other party call Waiting Indication Call Hold, other party Hold/Retrieved Indication Closed User Group supplementary service (CUG) Advice of Charge Unstructured SS Mobile Originated (MO) 3.10. Mounting the modules on your board The modules have been designed in order to be compliant with a standard lead-free SMT process. For detailed information about PCB pad design and conditions to use in SMT process, please refer to the respective Hardware User Guide. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 20 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 3.11. Packing system According to SMT process, for picking & placing movement requirements, UL865 is packaged on trays. Each tray contains 20 pieces in size of 176 x 329. The level of moisture sensibility of UL865 is "3", according with standard IPC/JEDEC J-STD-020, take care of all the relative requirements for using this kind of components. Special care for handling is highly required. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 21 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 4. Evaluation Kit In order to assist the customer in the development of the application, Telit offers the EVK2 Evaluation Kit that can be ordered separately. The EVK2 has a SIM card holder, the RS 232 serial port level translator, a direct UART connection, audio and antenna connector. The EVK2 provides a fully functional solution for a complete data or phone application. The standard serial RS232 9 pin connector placed on the Evaluation Kit allows the connection of the EVK2 system with a PC or other DTE. The development of the applications utilizing the Telit UL865 must present a proper design of all the interfaces towards and from the module (e.g. power supply, audio paths, level translators), otherwise a decrease in the performances will be introduced or, in the worst case, a wrong design can even lead to an operating failure of the module. In order to assist the hardware designer in his project phase, the EVK2 board presents a family of different solutions, which will cover the most common design requirements on the market, and which can be easily integrated in the OEM design as building blocks or can be taken as starting points to develop a specific one. For a detailed description of the Telit Evaluation Kit, please refer to the documentation provided with the respective Hardware User Guide and EVK2 User Manual. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 22 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 5. AT Commands The UL865 can be driven via the serial and USB interface using the standard AT commands. The modules are compliant with: 1. Hayes standard AT command set, in order to maintain the compatibility with existing S/W programs. 2. 3GPP TS 27.007 specific AT command and WCDMA/GPRS specific commands. 3. 3GPP TS 27.005 specific AT commands for SMS (Short Message Service) and CBS (Cell Broadcast Service) Moreover, the modules support also Telit proprietary AT commands for special purposes. For more information about the AT commands supported by the modules, please refer to the AT Commands Reference Guide. Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 23 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 6. Safety Recommendations READ CAREFULLY Be sure the use of this product is allowed in the country and in the environment required. The use of this product may be dangerous and has to be avoided in the following areas: Where it can interfere with other electronic devices in environments such as hospitals, airports, aircrafts, etc. Where there is risk of explosion such as gasoline stations, oil refineries, etc. It is responsibility of the user to enforce the country regulation and the specific environment regulation. Do not disassemble the product; any mark of tampering will compromise the warranty validity. We recommend following the instructions of the hardware user guides for a correct wiring of the product. The product has to be supplied with a stabilized voltage source and the wiring has to be conforming to the security and fire prevention regulations. The product has to be handled with care, avoiding any contact with the pins because electrostatic discharges may damage the product itself. Same cautions have to be taken for the SIM, checking carefully the instruction for its use. Do not insert or remove the SIM when the product is in power saving mode. The system integrator is responsible of the functioning of the final product; therefore, care has to be taken to the external components of the module, as well as of any project or installation issue, because the risk of disturbing the WCDMA/GSM network or external devices or having impact on the security. Should there be any doubt, please refer to the technical documentation and the regulations in force. Every module has to be equipped with a proper antenna with specific characteristics. The antenna has to be installed with care in order to avoid any interference with other electronic devices and has to guarantee a minimum distance from the body (20 cm). In case of this requirement cannot be satisfied, the system integrator has to assess the final product against the SAR regulation. The European Community provides some Directives for the electronic equipments introduced on the market. All the relevant information's are available on the European Community website: https://ec.europa.eu/growth/single-market/europeanstandards/harmonised-standards/rtte_en Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 24 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 The Directive 2014/53/EU regarding radio equipment is available at: https://ec.europa.eu/growth/sectors/electrical-engineering/reddirective_en while the applicable Directives (Low Voltage and EMC) are available at: https://ec.europa.eu/growth/sectors/electrical-engineering/lvddirective_en https://ec.europa.eu/growth/sectors/electrical-engineering/emcdirective_en Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 25 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 7. Conformity assessment issues Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 26 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 27 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 7.1. RTT&E Notified Body statement of Opinion Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 28 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 7.2. FCC certificate Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 29 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 30 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 7.3. IC certificates Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 31 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 8. List of acronyms 3GPP 3rd Generation Partnership Project ADC Analog to Digital Converter ADN Abbreviated Dialing Number A-GPS Assisted GPS AMR Adaptive Multi Rate AT Attention Commands AWS Advanced Wireless Services BER Bit Error Rate BGA Ball Grid Array CLIP Calling Line Identification Presentation CLIR Calling Line Identification Restriction CMOS Complementary Metal-Oxide Semiconductor CSD Circuit Switched Data DAC Digital to Analog Converter DARP Downlink Advanced Receiver Performance DTMF Dual Tone Multi Frequency FDN Fixed Dialing Number FTP File Transfer Protocol GSM Global System for Mobile communication GPRS General Packet Radio Service GPS Global Positioning System HSPA High Speed Packet Access HSUPA High Speed Uplink Packet Access H/W Hardware LED Light Emitting Diode MO Mobile Originated MT Mobile Terminated OEM Other Equipment Manufacturer Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 32 of 33 UL865 Product Description 80420ST10586A - Rev.4 - 2017-06-01 PCB Printed Circuit Board PCM Pulse Code Modulation PDA Personal Digital Assistant PDU Protocol Data Unit PIN Personal Identification Number POS Point Of Sales PWM Pulse Width Modulation RF Radio Frequency RoHS Restriction of Hazardous Substances RTC Real Time Clock SAIC Single Antenna Interface Cancellation SIM Subscriber Identity Module SMD Surface Mounted Device SMS Short Message Service S/W Software TBD To Be Determined TCP/IP Transmission Control Protocol/Internet Protocol TTSC Telit Technical Support Center UART Universal Asynchronous Receiver and Transmitter USB Universal Serial Bus USIM Universal Subscriber Identity Module WCDMA Wideband Code Division Multiple Access Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights Reserved. Page 33 of 33