UL865 Product Description
80420ST10586A Rev.4 2017-06-01
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 2 of 33
APPLICABILITY TABLE
PRODUCT
UL865-EUR
UL865-EUD
UL865-NAR
UL865-NAD
UL865-N3G
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 3 of 33
Disclaimer
The information contained in this document is the proprietary
information of Telit Communications S.p.A. and its affiliates
(“TELIT”).
The contents are confidential and any disclosure to persons
other than the officers, employees, agents or subcontractors
of the owner or licensee of this document, without the prior
written consent of Telit, is strictly prohibited.
Telit makes every effort to ensure the quality of the
information it makes available. Notwithstanding the foregoing,
Telit does not make any warranty as to the information
contained herein, and does not accept any liability for any
injury, loss or damage of any kind incurred by use of or
reliance upon the information.
Telit disclaims any and all responsibility for the application
of the devices characterized in this document, and notes that
the application of the device must comply with the safety
standards of the applicable country, and where applicable,
with the relevant wiring rules.
Telit reserves the right to make modifications, additions and
deletions to this document due to typographical errors,
inaccurate information, or improvements to programs and/or
equipment at any time and without notice.
Such changes will, nevertheless be incorporated into new
editions of this document.
Copyright: Transmittal, reproduction, dissemination and/or
editing of this document as well as utilization of its
contents and communication thereof to others without express
authorization are prohibited. Offenders will be held liable
for payment of damages. All rights are reserved.
Copyright © Telit Communications S.p.A. 2013.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 4 of 33
Contents
1. Introduction ................................................. 6
1.1. Scope ..................................................... 6
1.2. Audience .................................................. 6
1.3. Contact Information, Support .............................. 6
1.4. Text Conventions .......................................... 7
1.5. Related Documents ......................................... 7
1.6. Document History .......................................... 7
2. Overview ..................................................... 8
2.1. Product variants .......................................... 9
2.2. Target Market ............................................. 9
2.3. Features .................................................. 9
2.4. Approvals ................................................ 12
3. General Product Description ................................. 13
3.1. Dimensions and 2D mechanical drawing ..................... 13
3.2. Environmental requirements ............................... 14
3.2.1. Temperature range .......................................... 14
3.2.2. RoHS compliance ............................................ 14
3.3. Operating Frequency ...................................... 15
3.4. Transmitter output power ................................. 16
3.5. Supply voltage ........................................... 16
3.6. Power consumption ........................................ 17
3.7. Logic level .............................................. 17
3.8. Input and Outputs ........................................ 17
3.8.1. General Purpose I/Os ....................................... 17
3.8.2. Power on monitor (PWR_MON) ................................. 17
3.8.3. Power on/off control (ON_OFF) .............................. 18
3.8.4. Auxiliary power output for accessory (VAUX) ................ 18
3.8.5. SIM Reader ................................................. 18
3.8.6. Converters ................................................. 18
3.8.7. Audio Interface ............................................ 18
3.8.8. Serial ports ............................................... 18
3.8.9. USB port ................................................... 18
3.8.10. User Interface ........................................... 18
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 5 of 33
3.9. Features ................................................. 18
3.9.1. Speech Coding .............................................. 18
3.9.2. SMS ........................................................ 19
3.9.3. RTC Bypass out ............................................. 19
3.9.4. Data Transmission capabilities ............................. 19
3.9.5. Local security management .................................. 19
3.9.6. Call control ............................................... 19
3.9.7. Phonebook .................................................. 19
3.9.8. Characters management ...................................... 20
3.9.9. SIM related functions ...................................... 20
3.9.10. Call status indication ................................... 20
3.9.11. Automatic answer ......................................... 20
3.9.12. Supplementary services ................................... 20
3.10. Mounting the modules on your board ..................... 20
3.11. Packing system ......................................... 21
4. Evaluation Kit .............................................. 22
5. AT Commands ................................................. 23
6. Safety Recommendations ...................................... 24
7. Conformity assessment issues ................................ 26
7.1. RTT&E Notified Body statement of Opinion ................. 28
7.2. FCC certificate .......................................... 29
7.3. IC certificates .......................................... 31
8. List of acronyms ............................................ 32
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 6 of 33
1. Introduction
1.1. Scope
Scope of this document is to give an overview of the Telit
UL865 module, which can support GSM/GPRS/EDGE and WCDMA/HSPA
with data/voice capabilities.
1.2. Audience
This document is intended for customers who are evaluating the
UL865 product.
1.3. Contact Information, Support
For general contact, technical support, to report
documentation errors and to order manuals, contact Telit
Technical Support Center (TTSC) at:
TS-EMEA@telit.com
TS-NORTHAMERICA@telit.com
TS-LATINAMERICA@telit.com
TS-APAC@telit.com
Alternatively, use:
http://www.telit.com/en/products/technical-support-
center/contact.php
For detailed information about where you can buy the Telit
modules or for recommendations on accessories and components
visit:
http://www.telit.com
To register for product news and announcements or for product
questions contact Telit Technical Support Center (TTSC).
Our aim is to make this guide as helpful as possible. Keep us
informed of your comments and suggestions for improvements.
Telit appreciates feedback from the users of our information.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 7 of 33
1.4. Text Conventions
Danger This information MUST be followed or catastrophic
equipment failure or bodily injury may occur.
Caution or Warning Alerts the user to important points about
integrating the module, if these points are not followed, the
module and end user equipment may fail or malfunction.
Tip or Information Provides advice and suggestions that may
be useful when integrating the module.
All dates are in ISO 8601 format, i.e. YYYY-MM-DD.
1.5. Related Documents
UL865 Hardware User Guide, 1VV0301050
Telit EVK2 User Guide, 1vv0300704
1.6. Document History
Revision
Date
Changes
0
2013-02-04
First issue
1
2014-01-07
Updated Ch. 2.1, 3.2. Added
certifications in Ch.7
2
2014-04-28
Layout of table at Ch.2.1. Ch.2.3
3
2017-03-01
Updated certificates for new SW release
4
2017-06-01
Updated RED certificates
Updated SAFETY RECOMMENDATIONS
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 8 of 33
2. Overview
The UL865 Series further enriches the xL865 Family with a
number of UMTS/HSPA variants targeted at European (EMEA) and
North American (NA) markets. The dual-band UMTS/HSPA, dual-band
GSM/GPRS engine in the UL865 Series is voice-capable supporting
digital (DVI) interface. It delivers UMTS/HSPA 3GPP Release 7
compliant data communications and is equipped with a high-speed
USB 2.0 port, eight I/O ports, two A/D and one D/A converters.
For streamlined application development and system integration
the company offers RIL drivers for all major operating systems.
The UL865 features a VQFN packaging that is fully pad-level
compatible with its 2G companion, the GL865-DUAL V3.
As a part of Telit’s corporate policy of environmental
protection, all Telit products comply with the RoHS (Restriction
of Hazardous Substances) directive of the European Union (EU
Directive 2011/65/EU)
NOTE:
Some of the performances of the Telit modules depend on S/W
version installed on the module itself. The Telit modules S/W
group is continuously working in order to add new features and
improve the overall performances. The Telit modules are easily
upgraded by the developer using the Telit Flash Programmer.
NOTE:
In order to meet the competitive OEM and vertical market
stringent requirements, Telit supports its customers with a
dedicated Support Policy with:
Telit Evaluation Kit EVK2 to help you to develop your
application;
A website with all updated information available;
An high level specialist technical support to assist you in
your development;
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 9 of 33
2.1. Product variants
The following table describes the variants of UL865 series,
available for both EUx and NAx configurations as dual band in
2G&3G, plus an additional 3G-only variant for the North American
Market.
Variants
Freq. Bands
3G (MHz)
Features
UL865-EUR
900/1800
900/2100
Data&Voice
UL865-EUD
900/1800
900/2100
Data-only
UL865-NAR
850/1900
850/1900
Data&Voice
UL865-NAD
850/1900
850/1900
Data-only
UL865-N3G
N.A.
850/1900
Data&Voice
2.2. Target Market
The UL865 is designed and developed for applications such as:
Point-of-Sales (POS) terminals
mHealth Monitoring
Security alarms with cameras
Battery powered devices
Telemetry
Telematics, including Mapping and Infotainment
Handheld scanners and logistics devices
2.3. Features
Advanced E-GPRS/WCDMA/HSDPA/HSUPA Software protocol stack
(Layer 1 to 3) Version: 3GPP Release 7
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 10 of 33
GSM Quad band (900/1800 MHz for EUx, 850/1900 MHz for NAx)
WCDMA dual-band: B1&B8 for the EUx models and B2&B5 for
the NAx models
HSDPA up 7.2Mbps
HSUPA up to 5.76Mbps
WCDMA up to 384kbps downlink/uplink
DTM (Dual Transfer Mode)
CPC (DRX/DTX) (Continuous Packet Connectivity)
DARP
Control via AT commands according to 3GPP TS27.005, 27.007
and Telit customized AT commands
Serial port multiplexer 3GPP TS27.010
SIM application Tool Kits 3GPP TS 51.014
Power consumption (typical values)
- Stand-by current 2G, DRX9, 1.2 mA
- Stand-by current 3G, DRX7, 1.8 mA
Output power
- Class 4 (2W) @ 850 / 900 MHz, GSM
- Class 1 (1W) @ 1800 / 1900 MHz, GSM
- Class E2 (0.5W) @ 850/900 MHz, EDGE
- Class E2 (0.4W) @ 1800/1900 MHz, EDGE
- Class 3 (0.25W) @ 850/900/1900/2100 MHz, WCDMA
Interfaces
I/O ports including multi-functional I/Os
I2S for digital audio interface
USB 2.0 HS
1 UART
1 Auxiliary serial port (RX/TX only)
1 I2C
1.8V/3V SIM interface
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 11 of 33
Audio
Telephony, emergency call
HR, FR, EFR, AMR for GSM and AMR for WCDMA voice codec
Spatial Noise Suppression
Multiple audio profiles pre-programmed and fully
configurable
DTMF
SMS
Point to point mobile originated and mobile terminated SMS
Concatenated SMS supported
SMS cell broadcast
Text and PDU mode
SMS over GPRS
Data transmission
HSPA: category 8 in downlink e category 6 in uplink
DL up to 7.2Mbps
UL up to 5.76Mbps
WCDMA: up to 384kbps downlink/uplink
Asynchronous non-transparent CSD up to 9.6kbps
GPRS class 10 for NAx variants and class 33 for EUx
variants
EDGE class 10 for NAx variants and class 33 for EUx
variants
Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1
to 9 (EDGE)
GSM Supplementary Services
Call forwarding
Call barring
Call waiting & call hold
Advice of charge
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 12 of 33
Calling line identification presentation [CLIP]
Calling line identification restriction [CLIR]
Unstructured supplementary services mobile originated
data [USSD]
Closed user group
Additional features
SIM phonebook
Fixed Dialling Number (FDN)
Call control & status indication
SIM phonebook
Character management (IRA, UCS2, GSM)
USIM 3GPP Rel.7
Real Time Clock
Automatic answer
Alarm management
Embedded TCP/IP stack, including TCP, IP, UDP, and FTP
protocols
CSD for Video Telephony support
2.4. Approvals
Fully type approved confirming with R&TTE directive
CE, GCF
FCC, IC, PTCRB
AT&T
RoHS and REACH (all variants)
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 13 of 33
3. General Product Description
3.1. Dimensions and 2D mechanical drawing
UL865 has a QFN package, with 48 pads.
The overall dimensions of UL865 are:
Length: 24.4 mm
Width: 24.4mm
Thickness: 2.6 mm
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 14 of 33
3.2. Environmental requirements
3.2.1. Temperature range
Operating Temperature Range
40°C ~
+85°C
3.2.2. RoHS compliance
As a part of Telit corporate policy of environmental protection,
the UL865 complies with the RoHS (Restriction of Hazardous
Substances) directive of the European Union (EU directive
2011/65/EU). REACH compliant as well.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 15 of 33
3.3. Operating Frequency
The operating frequencies in GSM850, EGSM900, DCS1800, PCS1900,
WCDMA modes are compliant to the 3GPP and WCDMA specifications.
Mode
Freq. TX
(MHz)
Freq. RX
(MHz)
Channels
TX - RX
offset
GSM850
824.2 ~
848.8
869.2 ~ 893.8
128 ~ 251
45 MHz
EGSM900
890.0 ~
914.8
935.0 ~ 959.8
0 ~ 124
45 MHz
880.2 ~
889.8
925.2 ~
934.8
975 ~ 1023
45 MHz
DCS1800
1710.2 ~
1784.8
1805.2 ~
1879.8
512 ~ 885
95MHz
PCS1900
1850.2 ~
1909.8
1930.2 ~
1989.8
512 ~ 810
80MHz
WCDMA850
(band V)
826.4 ~
846.6
871.4 ~ 891.6
Tx: 4132 ~
4233
Rx: 4357 ~
4458
45MHz
WCDMA900
(band
VIII)
882.4 ~
912.6
927.4 ~ 957.6
Tx: 2712 ~
2863
Rx: 2937 ~
3088
45MHz
WCDMA1900
(band II)
1852.4 ~
1907.6
1932.4 ~
1987.6
Tx: 9262 ~
9538
Rx: 9662 ~
9938
80MHz
WCDMA2100
(Band I)
1922.4 ~
1977.6
2112.4 ~
2167.6
Tx: 9612 ~
9888
Rx: 10562 ~
10838
190MHz
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 16 of 33
3.4. Transmitter output power
The UL865 transceiver output of GSM/GPRS mode in 850/900MHz
bands are class 4 in accordance with the specifications which
determine the nominal 2W peak RF power (+33dBm) on 50ohm. In the
1800/1900MHz bands are class 1 in accordance with the
specification which determines the nominal 1W peak RF power
(+30dBm) on 50ohm.
The UL865 transceiver output of EDGE mode in 850/900MHz bands
are class E2 in accordance with the specifications which
determine the nominal 0.5W peak RF power (+27dBm) on 50ohm. In
the 1800/1900MHz bands are class E2 in accordance with the
specification which determine the nominal 0.4W peak RF power
(+26dBm) on 50ohm.
The UL865 transceiver output of WCDMA mode in
850/900/1900/2100MHz bands is class 3 in accordance with the
specifications which determine the nominal 0.25W peak RF power
(+24dBm) on 50ohm.
3.5. Supply voltage
The external power supply must be connected to VBATT signal and
must fulfill the following requirements:
Nominal Supply Voltage
3.8V
Operating Voltage Range
3.4 ~ 4.2V
Extended Operating Voltage
Range
3.22 ~ 4.5V
CAUTION:
The operating voltage MUST not be exceeded; Special care must
be taken when designing the application’s power supply section
to avoid an excessive voltage drop. If the voltage drop is
exceeding the limits it could cause a Power Off of the module.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 17 of 33
3.6. Power consumption
The UL865 power consumptions are described in the following
table
Depending on network configuration and not under module control
3.7. Logic level
Where not specifically stated, the most of interface circuits
work at 1.8V CMOS logic levels. To get more detailed information
about the logic level specifications used for UL865, please
refer to the Hardware User Guide.
3.8. Input and Outputs
3.8.1. General Purpose I/Os
Pins of general purpose I/Os can be configured by AT command in
three different ways as input, output and alternative function.
3.8.2. Power on monitor (PWR_MON)
The PWR_MON indicates the status of the module running properly.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 18 of 33
3.8.3. Power on/off control (ON_OFF)
External power on/off control input. Refer to the Hardware User
Guide for more details of Power on timing.
3.8.4. Auxiliary power output for accessory (VAUX)
A regulated 1.8V power output is provided for an external
device.
3.8.5. SIM Reader
The UL865 family supports 1 SIM/USIM at 1.8V and 3V ONLY with
and external SIM connector. For 5V SIM, an external level
translator can be added. Refer to the UL865 Hardware User Guide.
3.8.6. Converters
The UL865 family has 2 ADC and 1DAC.
3.8.7. Audio Interface
A Digital Audio bus is available.
3.8.8. Serial ports
Two serial ports are available.
Full RS232-C
Auxiliary serial port (RX/TX only)
3.8.9. USB port
The USB2.0 High Speed has a clock rate of 480MHz
3.8.10. User Interface
The user interface is managed by AT commands according to ITU-T
V.250, 3GPP 27.007 and 27.005 specifications. Please refer to
the AT command User Guide for complete details.
3.9. Features
3.9.1. Speech Coding
The UL865 support the following voice codecs:
Adaptive Multi Rate for WCDMA
Half Rate, Full Rate, Enhanced Full Rate, Adaptive Multi
Rate for GSM
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 19 of 33
3.9.2. SMS
The UL865 supports the following SMS types:
Mobile Terminated (MT) class 0 ~ 3 with signaling of new
incoming SMS, SIM full, SMS read
Mobile Originated class (MO) 0 ~ 3 with writing, saving in
SIM and sending
Cell broadcast compatible with CB DRX signaling of new
incoming SMS.
The module supports also SMS over GPRS
3.9.3. RTC Bypass out
The VRTC pin brings out the Real Time Clock supply, which is
separate from the rest of the digital part, allowing having
only RTC going on when all the other parts of the device are
off.
To this power output a backup capacitor can be added in order
to increase the RTC autonomy during power off of the battery.
NO Devices must be powered from this pin.
3.9.4. Data Transmission capabilities
The UL865 supports:
HSPA: D/L up to 7.2Mbps, U/L up to 5.76Mbps
Asynchronous non-transparent CSD up to 9.6kbps for GSM,
14.4kbps for WCDMA
EDGE Class 10 for NAx variants and Class 33 for EUx
variants
Coding scheme 1 to 4 (GPRS) & Modulation Coding scheme 1
to 9 (EDGE)
3.9.5. Local security management
The local security management can be done with the lock of
Universal Subscriber Identity Module (USIM), and the security
code will be requested at power-up.
3.9.6. Call control
The calling cost control function is supported.
3.9.7. Phonebook
This function allows storing the telephone numbers into SIM
memory. The capability depends on the SIM version and its
embedded memory.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 20 of 33
3.9.8. Characters management
The UL865 supports the IRA, GSM, PCCP437, 8859-1 and UCS2
character sets, EXT and PDU mode.
3.9.9. SIM related functions
Activation and deactivation of the numbers stored in phone book
FDN (Fixed Dialing Numbers), ADN (Abbreviated Dialing Number)
and PIN insertion are supported. Extension at the PIN2 for the
PUK2 insertion capability for lock condition is supported too.
3.9.10. Call status indication
The call status indication is supported.
3.9.11. Automatic answer
The automatic answering feature is supported. The
user/application can specify the number of rings after which the
module will make an answer automatically.
3.9.12. Supplementary services
The following supplementary services are supported:
Call Barring
Call Forwarding
Calling Line Identification Presentation (CLIP)
Calling Line Identification Restriction (CLIR)
Call Waiting, other party call Waiting Indication
Call Hold, other party Hold/Retrieved Indication
Closed User Group supplementary service (CUG)
Advice of Charge
Unstructured SS Mobile Originated (MO)
3.10. Mounting the modules on your board
The modules have been designed in order to be compliant with a
standard lead-free SMT process. For detailed information about
PCB pad design and conditions to use in SMT process, please
refer to the respective Hardware User Guide.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 21 of 33
3.11. Packing system
According to SMT process, for picking & placing movement
requirements, UL865 is packaged on trays. Each tray contains 20
pieces in size of 176 x 329.
The level of moisture sensibility of UL865 is 3, according
with standard IPC/JEDEC J-STD-020, take care of all the relative
requirements for using this kind of components. Special care for
handling is highly required.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 22 of 33
4. Evaluation Kit
In order to assist the customer in the development of the
application, Telit offers the EVK2 Evaluation Kit that can be
ordered separately. The EVK2 has a SIM card holder, the RS 232
serial port level translator, a direct UART connection, audio
and antenna connector.
The EVK2 provides a fully functional solution for a complete
data or phone application. The standard serial RS232 9 pin
connector placed on the Evaluation Kit allows the connection of
the EVK2 system with a PC or other DTE.
The development of the applications utilizing the Telit UL865
must present a proper design of all the interfaces towards and
from the module (e.g. power supply, audio paths, level
translators), otherwise a decrease in the performances will be
introduced or, in the worst case, a wrong design can even lead
to an operating failure of the module.
In order to assist the hardware designer in his project phase,
the EVK2 board presents a family of different solutions, which
will cover the most common design requirements on the market,
and which can be easily integrated in the OEM design as building
blocks or can be taken as starting points to develop a specific
one.
For a detailed description of the Telit Evaluation Kit, please
refer to the documentation provided with the respective Hardware
User Guide and EVK2 User Manual.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 23 of 33
5. AT Commands
The UL865 can be driven via the serial and USB interface using
the standard AT commands.
The modules are compliant with:
1. Hayes standard AT command set, in order to maintain the
compatibility with existing S/W programs.
2. 3GPP TS 27.007 specific AT command and WCDMA/GPRS specific
commands.
3. 3GPP TS 27.005 specific AT commands for SMS (Short Message
Service) and CBS (Cell Broadcast Service)
Moreover, the modules support also Telit proprietary AT commands
for special purposes.
For more information about the AT commands supported by the
modules, please refer to the AT Commands Reference Guide.
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 24 of 33
6. Safety Recommendations
READ CAREFULLY
Be sure the use of this product is allowed in the country and
in the environment required. The use of this product may be
dangerous and has to be avoided in the following areas:
Where it can interfere with other electronic devices in
environments such as hospitals, airports, aircrafts, etc.
Where there is risk of explosion such as gasoline
stations, oil refineries, etc. It is responsibility of
the user to enforce the country regulation and the
specific environment regulation.
Do not disassemble the product; any mark of tampering will
compromise the warranty validity. We recommend following the
instructions of the hardware user guides for a correct wiring
of the product. The product has to be supplied with a
stabilized voltage source and the wiring has to be conforming
to the security and fire prevention regulations. The product
has to be handled with care, avoiding any contact with the
pins because electrostatic discharges may damage the product
itself. Same cautions have to be taken for the SIM, checking
carefully the instruction for its use. Do not insert or remove
the SIM when the product is in power saving mode.
The system integrator is responsible of the functioning of the
final product; therefore, care has to be taken to the external
components of the module, as well as of any project or
installation issue, because the risk of disturbing the
WCDMA/GSM network or external devices or having impact on the
security. Should there be any doubt, please refer to the
technical documentation and the regulations in force. Every
module has to be equipped with a proper antenna with specific
characteristics. The antenna has
to be installed with care in order to avoid any interference
with other electronic devices and has to guarantee a minimum
distance from the body (20 cm). In case of this requirement
cannot be satisfied, the system integrator has to assess the
final product against the SAR regulation.
The European Community provides some Directives for the
electronic equipments introduced on the market.
All the relevant information’s are available on the European
Community website:
https://ec.europa.eu/growth/single-market/european-
standards/harmonised-standards/rtte_en
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 25 of 33
The Directive 2014/53/EU regarding radio equipment is available at:
https://ec.europa.eu/growth/sectors/electrical-engineering/red-
directive_en
while the applicable Directives (Low Voltage and EMC) are available at:
https://ec.europa.eu/growth/sectors/electrical-engineering/lvd-
directive_en
https://ec.europa.eu/growth/sectors/electrical-engineering/emc-
directive_en
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 26 of 33
7. Conformity assessment issues
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 27 of 33
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 28 of 33
7.1. RTT&E Notified Body statement of Opinion
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 29 of 33
7.2. FCC certificate
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 30 of 33
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 31 of 33
7.3. IC certificates
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 32 of 33
8. List of acronyms
3GPP
3rd Generation Partnership Project
ADC
Analog to Digital Converter
ADN
Abbreviated Dialing Number
A-GPS
Assisted GPS
AMR
Adaptive Multi Rate
AT
Attention Commands
AWS
Advanced Wireless Services
BER
Bit Error Rate
BGA
Ball Grid Array
CLIP
Calling Line Identification Presentation
CLIR
Calling Line Identification Restriction
CMOS
Complementary Metal-Oxide Semiconductor
CSD
Circuit Switched Data
DAC
Digital to Analog Converter
DARP
Downlink Advanced Receiver Performance
DTMF
Dual Tone Multi Frequency
FDN
Fixed Dialing Number
FTP
File Transfer Protocol
GSM
Global System for Mobile communication
GPRS
General Packet Radio Service
GPS
Global Positioning System
HSPA
High Speed Packet Access
HSUPA
High Speed Uplink Packet Access
H/W
Hardware
LED
Light Emitting Diode
MO
Mobile Originated
MT
Mobile Terminated
OEM
Other Equipment Manufacturer
UL865 Product Description
80420ST10586A - Rev.4 2017-06-01
Reproduction forbidden without written authorization from Telit Communications S.p.A. - All Rights
Reserved. Page 33 of 33
PCB
Printed Circuit Board
PCM
Pulse Code Modulation
PDA
Personal Digital Assistant
PDU
Protocol Data Unit
PIN
Personal Identification Number
POS
Point Of Sales
PWM
Pulse Width Modulation
RF
Radio Frequency
RoHS
Restriction of Hazardous Substances
RTC
Real Time Clock
SAIC
Single Antenna Interface Cancellation
SIM
Subscriber Identity Module
SMD
Surface Mounted Device
SMS
Short Message Service
S/W
Software
TBD
To Be Determined
TCP/IP
Transmission Control Protocol/Internet Protocol
TTSC
Telit Technical Support Center
UART
Universal Asynchronous Receiver and Transmitter
USB
Universal Serial Bus
USIM
Universal Subscriber Identity Module
WCDMA
Wideband Code Division Multiple Access