International Safety Standard Approvals
VDE0805/EN60950/IEC950 File No. 10401-3336-1073
UL1950 File No. E136005
CSA C22.2 No. 950 File No. LR41062C
BXA75 SERIES
Single output
[ 2 YEAR WARRANTY ]
• 3.5 x 2.4 x 0.5 inch package with stand-offs
• 19 Watts/in3power density
• Efficiency up to 87%
• CISPR 22 and EN55022 conducted emissions level A
• UL, VDE and CSA safety approvals
• Indefinite short circuit protection
• Baseplate operating temperature range of –25°C to +85°C
The BXA75 series are high density DC/DC converters ideally suited for a wide variety
of communications, industrial, computer and distributed power applications. With up
to 80 Watts of power in a 3.5 x 2.4 x 0.5 inch package and efficiencies as high as
87%, the BXA75 can address a host of demanding power requirements, offering a
wide input range of 36-75VDC with industry standard outputs of 3.3V, 5V, 12V and
15V. Approval to EN60950 and EN41003 coupled with conducted emissions
compliance to CISPR 22, FCC and EN55022 level A, facilitate easy and cost effective
design-in for communications systems. The demands of industrial systems are met by
a baseplate operating temperature range of –25°C to 85°C, overvoltage,
overtemperature and short circuit protection, along with tight load and line regulation
and output ripple as low as 15mV rms. Other standard features include remote enable,
remote sense and external trim.
SPECIFICATION
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
PAGE 1
Data Sheet © Artesyn Technologies
®
2000
The information and specifications contained in this data sheet are believed to be correct at
time of publication. However, Artesyn Technologies accepts no responsibility for
consequences arising from printing errors or inaccuracies. Specifications are subject to
change without notice. No rights under any patent accompany the sale of any such
product(s) or information contained herein.
OUTPUT SPECIFICATIONS
Voltage adjustability 3.3V and 15V +10%, -3.0%
5V and 12V +10%, -5.0%
Voltage accuracy ±0.5%
Remote sense 0.5V line drop compensation
Total error band (See Note 2) ±2.0%
Line regulation Typical ±0.15%
Load regulation Typical ±0.3%
Ripple and noise 5Hz-20MHz, 50mV pk-pk
(See Note 3) 15mV rms max.
No external capacitor 100mV pk-pk,
25mV rms max.
Transient response ±4.0% max. dev.
(75% to 100% load step) 100µs recovery
to within 1% Vo
Temperature coefficient ±0.02%/°C Max.
Overvoltage protection (See Note 5) Yes, see table
Short circuit protection Continuous
automatic recovery
INPUT SPECIFICATIONS
Input voltage range 36 to 75VDC
Input filter (See Note 4) Yes
Remote ON/OFF
Logic compatibility (Ref. to -Vin) CMOS/TTL
ON >3.5VDC or open circuit
OFF <0.8VDC
Shutdown idle current Less than 50mA
EMC CHARACTERISTICS
Conducted noise EN55022, FCC (See Note 4) Level A
Surge susceptibility 100V No damage
GENERAL SPECIFICATIONS
Efficiency See table
Isolation voltage 1500VDC
Switching frequency 500kHz ±5.0%
Approvals and VDE0805, EN60950
standards IEC950, UL1950
CSA C22.2 No. 950
Case material Plastic with
aluminum baseplate
Material flammability UL94V-0
Weight 160g (5.65oz)
MTBF Bellcore, 2,600,000 hours
25°C baseplate minimum
ENVIRONMENTAL SPECIFICATIONS
Thermal performance Operating, See curves -25°C to +85°C
(See Note 6) Non-operating –55°C to +125°C
Over temperature 115°C internal
shutdown temperature
auto. recovery
Altitude Operating 10,000 feet max.
Non operating 40,000 feet max.
Vibration 5Hz to 500Hz 2.4G RMS (approx.)