5962-9071202M2C - Maxim Integrated

SCOPE: MICROPROCESSOR SUPERVISORY CIRCUITS

Device Type Generic Number

01 MAX690(x)/883B

02 MAX691(x)/883B

03 MAX692(x)/883B

04 MAX693(x)/883B

05 MAX694(x)/883B

06 MAX695(x)/883B

Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:

Outline Letter Mil-Std-1835 Case Outline Package Code

MAXIM SMD

JA P GDIP1-T08 or CDIP2-T08 8 LEAD CERDIP J08

JE E GDIP1-T16 or CDIP2-T16 16 LEAD CERDIP J16

FB X CDFP3-F10 10 LEAD Flatpack F10

LP 2 CQCC1-N20 20 Pin Leadless Chip L20

A bsolute Maximum Ratings

Terminal Voltage (with respect to GND)

VCC .................................................................................................................. -0.3V to +6.0V

VBATT ................................................................................................................ -0.3V to+6.0V

All other Inputs 1/ ................................................................................. -0.3V to (VOUT+0.5V)

Input Current

VCC ............................................................................................................................... 200mA

VBATT .............................................................................................................................. 50mA

GND ............................................................................................................................... 20mA

Output Current

VOUT .................................................................................................. Short-circuit protected

All other outputs ........................................................................................................... 20mA

Rate of Rise, VCC, VBATT ................................................................................................ 100V/µs

Lead Temperature (soldering, 10 seconds) ...................................................................... +300°C

Storage Temperature ......................................................................................... -65°C to +160°C

Continuous Power Dissipation ................................................................................... TA=+70°C

8 lead CERDIP(derate 8.0mW/°C above +70°C) ..................................................... 640mW

16 lead CERDIP(derate 10.0mW/°C above +70°C) ................................................. 800mW

10 lead Flatpack(derate 5.3mW/°C above +70°C) ................................................... 421mW

20 lead LCC(derate 9.1mW/°C above +70°C) ......................................................... 727mW

Junct ion Temperature TJ ............................................................................................ +150°C

Thermal Resista nce, J unction to Case, ΘJC:

Case Outline 8 lead CERDIP..................................................................... 55°C/W

Case Outline 16 lead CERDIP................................................................... 50°C/W

Case Outline 10 lead Flatpack .................................................................. 85°C/W

Case Outline 20 leadless Chip carrier ....................................................... 20°C/W

Thermal Resistance, Junction to Ambient, ΘJA:

Case Outline 8 lead CERDIP................................................................... 125°C/W

Case Outline 16 lead CERDIP................................................................. 100°C/W

Case Outline 10 lead Flatpack ................................................................ 190°C/W

Case Outline 20 leadless Chip carrier ..................................................... 110°C/W

NOTE 1: The input voltage limits on PFI and WDI may be exceeded if the input current is less than 10mA.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device.

These are stress ratings only, and functional operation of the device at these or any other conditions beyond

those indicated in the operational section s of the sp ecifica tions is not implied. Exposure to absolute maximum

rating conditions for extended periods may affect device reliability.

---------------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

/695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 2 of 8

Recommended Operating Conditions

Ambient Operating Range (TA) ............................................................... -55°C to +125°C

Supply Voltage Range (VCC) DASH 03 & 04 ............................................ +4.5V to +5.5V

Supply Voltage Range (VCC) DASH 01, 02, 05, 06 ................................. +4.75V to +5.5V

TABLE 1. ELECTRICAL TESTS:

TEST Symbol

CONDITIONS

-55 °C ≤TA≤+125°C 2/

Unless otherwise specified Group A

Subgroup Device

type Limits

Min Limits

Max Units

BATTERY-BACKUP SWITCHING

Operating Voltage

Range VCC 1,2,3 01,02,

05,06

03,04

4.75

4.5

5.5

5.5 V

Operating Voltage

Range VBATT 1,2,3 01,02,

05,06

03,04

2.0

4.25

4.0 V

Output Voltage VOUT IOUT=1mA

IOUT=50mA 1,2,3 All VCC-0.3

VCC-0.5 V

Output Voltage-

Battery-Backup

Mode

BATT

OUT

IOUT=250µA, VCC<VBATT-0.2V 1,2,3 All VBATT-

0.1 V

Supply Current

(Excludes IOUT)I

IOUT=1mA

IOUT=50mA

2,3

All

Supply Current in

Battery-Backup

Mode

IBATT VCC=0V, VBATT=2.8V 1

2,3 All 1

10 µA

Battery Standby

Current BATT

SBI 5.5V>VCC>VBATT+1V

+=Discharge, -=Charge 1

2,3 All -0.10

-1.00 +0.02

+0.02 µA

Battery-

Switchover,

Threshold, VCC to

VBATT

BATT

SWTH

Power-Up or Power-Down 1,2,3 All -200 +200 mV

BATT ON Output

Voltage BATT

ONOUT

ISINK=3.2mA 1,2,3 02,04,06 0.4 V

BATT ON Output

Short-Circuit

Current

BATT

ONIOS

BATT ON = VOUT

BATT ON =0V Source Current 1,2,3 02,04,06 0.1

µA

RESET A ND WATCHDOG TIMING

Reset Voltage

Threshold RTH

1,2,3

01,02,

05,06

03,04

4.5

4.25

4.75

4.5 V

Reset Threshold

Hysteresis RTHH 1,2,3 All 250 mV

Reset Timeout

Delay RDEL OSC SEL High, VCC=5V

10,11

01,02

03,04

05,06

140

126

280

310 ms

---------------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

/695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 3 of 8

TEST Symbol

CONDITIONS

-55 °C ≤TA≤+125°C 2/

Unless otherwise specified Group A

Subgroup Device

type Limits

Min Limits

Max Units

Watchdog Timeout

Period, Internal

Oscillator WDINT

Long Period, VCC=5V

Short Period, VCC=5V

10,11

All

1.00

0.90

2.25

2.42

140

154

sec

Watchdog Timeout

Period, External

Clock WDEXT

Long Period

Short Period

10,11

02,04,06

3840

768

4097

1025

Clock

Cycles

Minimum WDI

Input Pulse Width WDIPW VIL=0.4V, VIH=VCC(0.8) 9

10,11 All 200

300 ns

______

RESET Output

Voltage High

RVOH

ISOURCE=1µA, VCC=5V 1,2,3 All 3.5 V

______

RESET Output

Voltage Low

RVOL

ISINK=1.6mA, VCC=4.25V

ISINK=800µA, VCC=4.25V

2,3 All 0.4

0.4 V

_________

LOWLINE Output

Voltage High

LLVOH

ISOURCE=1µA, VCC=5V 1,2,3 02,04,06 3.5 V

_________

LOWLINE Output

Voltage Low

LLVOL

ISINK=1.6mA, VCC=4.25V

ISINK=800µA, VCC=4.25V

2,3 02,04,06 0.4

0.4 V

____

WDO Output

Voltage High

____

WDO

VOH

ISOURCE=1µA, VCC=5V 1,2,3 All 3.5 V

____

WDO Output

Voltage Low

____

WDO

VOL

ISINK=1.6mA, VCC=4.25V

ISINK=800µA, VCC=4.25V

2,3 02,04,06 0.4

0.4 V

Reset Output

Voltage High RVOH ISOURCE=1µA, VCC=5V 1,2,3 02,04,06 3.5 V

Reset Output

Voltage Low RVOL ISINK=1.6mA

ISINK=800µA

2,3 02,04,06 0.4

0.4 V

Output Short-

Circuit Current IOS

______

RESET=0V

______ ____ __

RESET, RESET, WDO, LL

1,2,3 All

02,04,06

µA

WDI Input

Threshold Logic

Low

WDI

VIL

VCC=5V NOTE 3 1

2,3 All 0.8

0.4 V

WDI Input

Threshold Logic

High

WDI

VIH

VCC=5V NOTE 3 1

2,3 All 3.5

4.0 V

WDI Input Current WDIIN WDI=VOUT

WDI=0V

2,3

All -50

-80

80 µA

---------------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

/695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 4 of 8

TEST Symbol

CONDITIONS

-55 °C ≤TA≤+125°C 2/

Unless otherwise specified Group A

Subgroup Device

type Limits

Min Limits

Max Units

POWER-FAIL DETECTOR

PFI Input

Threshold PFIVTH VCC=5V 1,2,3 All 1.2 1.4 V

PFI Input Current PFIIIN 1,2,3 All -25 25 nA

___

PFO Output

Voltage High

___

PFOVOH ISOURCE=1µA, VCC=5V 1,2,3 All 3.5 V

___

PFO Output

Voltage Low

___

PFOVOL

ISINK=3.2mA

ISINK=1.6mA

2,3 All 0.4

0.4 V

___

PFO Short-Circuit

Sourc e Current

___

PFOIOS

___

PFI=VIH, PFO=0V 1,2,3 All 1.0 25 µA

CHIP-ENABLE GATING

CE IN Thresholds

Logic Low

CEVIL

2,3 02,04,06 0.8

0.4 V

CE IN Thresholds

Logic High

CEVIH

2,3 02,04,06 3.0

4.0 V

CE IN Pull-Up

Current

CE INPI 1,2,3 02,04,06 1.0 25 µA

CE OUT Output

Voltage High

CEVOH

ISOURCE=3.0mA,

VCC=4.75V

ISOURCE=1µA, VCC=0V

1,2,3 02,04,06 VOUT-1.5

VOUT-0.05 V

CE Output Voltage

Low

CEVOL

ISINK=3.2mA

ISINK=1.6mA

2,3 02,04,06 0.4

0.4 V

CE Propagation

Delay

___

tPDCE VCC=5V 9

10,11 02,04,06 200

300 ns

OSCILLATOR

OSC IN Input

Current Pull-Up OSCIIN 1,2,3 02,04,06 25 µA

OSC SEL Input

Pull-Up Current OSC

SELIN

1,2,3 02,04,06 1 25 µA

OSC IN Frequency

Range OSC

INfrq OSC SEL=0V 9,10,11 02,04,06 0 250 kHz

OSC IN Frequency

with External

Capacitor

OSCIN OSC SEL=0V, COSC=47pF

NOTE 4 9 02,04,06 4 kHz

NOTE 2: VCC=full ope rating r ange, VBATT=+2.8V.

NOTE 3: WDI is guaranteed to be in the mid-level (inactive) state if WDI is floating and VCC is in the operating

range. WDI is internally biased to 38% of VCC with an impedance of approximately 125kΩ

NOTE 4: Typical for design purposes only but not tested. Guaranteed for SMD 5962-90711 and 5962-90712.

---------------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

/695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 5 of 8

Package ORDERING INFORMATION: SMD NUMBER

01 8 pin CERDIP MAX690MJA/883B 5962-9071201MPA

01 10 pin Flatpack MAX690MFB/883B 5962-9071201MXC

01 20 pin LCC MAX690MLP/883B 5962-9071201M2C

02 8 pin CERDIP MAX691MJA/883B 5962-9071101MPA

02 20 pin LCC MAX691MLP/883B 5962-9071101M2C

03 8 pin CERDIP MAX692MJA/883B 5962-9071202MPA

03 10 pin Flatpack MAX692MFB/883B 5962-9071202MXC

03 20 pin LCC MAX692MLP/883B 5962-9071202M2C

04 8 pin CERDIP MAX693MJA/883B 5962-9071102MPA

04 20 pin LCC MAX693MLP/883B 5962-9071102M2C

05 8 pin CERDIP MAX694MJA/883B 5962-9071203MPA

05 10 pin Flatpack MAX694MFB/883B 5962-9071203MXC

05 20 pin LCC MAX694MLP/883B 5962-9071203M2C

06 8 pin CERDIP MAX695MJA/883B 5962-9071103MPA

TERMINAL CONNEC TIONS:

MAX690/692/694 MAX690/692/694 MAX690/692/694 MAX691/693/695 MAX691/693

J8 F10 L20 J16 L20

OUT VOUT NC VBATT NC

CC VCC VBATT VOUT VBATT

3 GND GND VOUT VCC VOUT

4PFI NC V

CC GND VCC

5 ____

PFO PFI GND BATT ON GND

6 WDI ____

PFO NC _________

LOWLINE NC

7 ______

RESET WDI NC OSC IN BATT ON

BATT NC NC OSC SEL _________

LOWLINE

9 ______

RESET NC PFI OSC IN

10 VBATT NC ____

PFO OSC SEL

11 NC WDI NC

12 PFI __

CE OUT PFI

13 ____

PFO __

CE IN ____

PFO

14 WDI ____

WDO WDI

15 NC ______

RESET __

CE OUT

16 NC RESET NC

17 NC __

CE IN

18 NC ____

WDO

19 ______

RESET ______

RESET

20 NC RESET

---------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

------ /695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 6 of 8

QUALITY ASSURAN CE

Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil-

Std-883.

Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015:

1. Test Condition, A, B, C, or D.

2. TA = +125°C minimum.

3. Interim and final electrical test requirements shall be specified in Table 2.

Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B,

C, and D inspection.

Group A inspection:

1. Tests as specified in Table 2.

2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted.

Group C and D inspections:

a. End-point electrical parameters shall be specified in Table 1.

b. Steady-state life test, Method 1005 of Mil-Std-883:

1. Test condition A, B, C, D.

2. TA = +125°C, minimum.

3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883.

TABLE 2. ELECTRICAL TEST REQUIREMENTS

Mil-Std-883 Test Requirements Subgroups

per Method 5005, Table 1

Interim Electric Parameters

Method 5004 1

Final Electrical Parameters

Method 5005 1*, 2, 3, 9, 10, 11

Group A Test Requirements

Method 5005 1, 2, 3, 9, 10, 11

Group C and D End-Point Electrical Parameters

Method 5005 1

* PDA applies to Subgroup 1 only.

---------------------- Electrical Characteristics of MAX690/691/692/693/694 19-2553 Rev. C

------ /695/883B for /883B and SMD 5962-90711 and 5962-90712 Page 7 of 8

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

MAX690CPA+ MAX690EPA+ MAX691CWE+ MAX691EWE+ MAX692CPA+ MAX693CPE+ MAX693CWE+

MAX694CPA+ MAX694EPA+ MAX695CPE+ MAX695CWE+ MAX690MJA/883B MAX691MJE/883B

MAX692MJA/883B MAX693MJE/883B MAX694MJA/883B MAX695MJE/883B MAX691CPE+ MAX691CWE+T

MAX691EPE+ MAX691EWE+T MAX692EPA+ MAX693CWE+T MAX693EPE+ MAX693EWE+ MAX693EWE+T

MAX695CWE+T MAX695EPE+ MAX695EWE+ MAX695EWE+T MAX690MLP/883B MAX691MLP/883B

MAX693EJE MAX690MJA MAX691EJE MAX691EWE MAX693MJE MAX194ACWE+T 5962-9071202M2C

MAX194ACWE+ MAX690EJA MAX691MJE