EVERLIGHT ELECTRONICS CO.,LTD. Technical Data Sheet 0603 Package Chip LED (0.4mm Height) 19-217/G7C-AN1P2/3T Features Package in 8mm tape on 7diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow solder process. Mono-color type. Pb-free. RoHS refer to SMD B TYPE SGS report. Descriptions The 19-217 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained. Besides, lightweight makes them ideal for miniature applications. etc. Applications Automotive: backlighting in dashboard and switch. Telecommunication: indicator and backlighting in telephone and fax. Flat backlight for LCD, switch and symbol. General use. Device Selection Guide Chip Part No. Emitted Color Lens Color Brilliant Yellow Green Water Clear Material 19-217/G7C-AN1P2/3T Everlight Electronics Co., Ltd. Device No. : DSE-197- AlGaInP http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 1 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Package Outline Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 2 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Absolute Maximum Ratings (Ta=25) Parameter Symbol Rating Unit Reverse Voltage VR 5 V Forward Current IF 25 mA Operating Temperature Topr -40 ~ +85 Storage Temperature Tstg -40 ~ +90 Soldering Temperature Tsol 260 (for 5 seconds) Electrostatic Discharge ESD 2000 V Power Dissipation Pd 60 mW IFP 60 mA Peak Forward Current (Duty 1/10 @1KHz) Reflow Soldering : 260 for 10 sec. Soldering Temperature Everlight Electronics Co., Ltd. Device No. : DSE-197- Tsol Hand Soldering : 350 for 3 sec. http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 3 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Luminous Intensity Iv 28.5 ----- 72.0 mcd Peak Wavelength p ---- 575 ---- nm Dominant Wavelength d 569.5 ---- 577.5 nm Spectrum Radiation Bandwidth ---- 20 ---- nm Viewing Angle 21/2 ---- 120 ---- deg Forward Voltage VF ---- 2.0 2.4 V Reverse Current IR ---- ---- 10 A Condition IF=20mA VR=5V Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm 3.Tolerance of Forward Voltage 0.05V Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 4 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Bin Range Of Dom. Wavelength Group A Bin Min Max C16 569.5 571.5 C17 571.5 573.5 C18 573.5 575.5 C19 575.5 577.5 Unit Condition nm IF=20mA Unit Condition mcd IF=20mA Bin Range Of Luminous Intensity Bin Min Max N1 28.5 36.0 N2 36.0 45.0 P1 45.0 57.0 P2 57.0 72.0 Notes: 1.Tolerance of Luminous Intensity 10% 2.Tolerance of Dominant Wavelength 1nm Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 5 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Typical Electro-Optical Characteristics Curves Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 6 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Label explanation CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 7 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Moisture Resistant Packaging Label Aluminum moisture-proof bag Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Desiccant Rev. 1 Label Page: 8 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Reliability Test Items And Conditions The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% Test Sample Hours/Cycles Size No. Items Test Condition 1 Reflow Soldering Temp. : 2605 Min. 5sec. 6 Min. 22 PCS. 0/1 Temperature Cycle H : +100 15min 5 min L : -40 15min 300 Cycles 22 PCS. 0/1 Thermal Shock H : +100 5min 10 sec L : -10 5min 300 Cycles 22 PCS. 0/1 Temp. : 100 1000 Hrs. 22 PCS. 0/1 Temp. : -40 1000 Hrs. 22 PCS. 0/1 2 3 4 5 High Temperature Storage Low Temperature Storage Ac/Re 6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1 7 High Temperature / High Humidity 85/ 85%RH 1000 Hrs. 22 PCS. 0/1 Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 9 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package: The LEDs should be kept at 30 or less and 90%RH or less. 2.3 After opening the package : The LEDs should be kept at 30 or less and 70%RH or less(Floor life). However, it's recommended that the LEDs should be used within 168 hours (7 days) after opening the package. If unused LEDs remain, it should be stored in moisture proof packages. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No. : DSE-197- http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 10 of 11 Prepared by: Ashley Kuo EVERLIGHT ELECTRONICS CO.,LTD. 19-217/G7C-AN1P2/3T 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No. : DSE-197- Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date: 05-Jul-2005 Rev. 1 Page: 11 of 11 Prepared by: Ashley Kuo