EVERLIGHT ELECTRONICS CO.,LTD.
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 1 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Technical Data Sheet
0603 Package Chip LED (0.4mm Height)
19-217/G7C-AN1P2/3T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․RoHS refer to SMD B TYPE SGS report.
Descriptions
․The 19-217 SMD Taping is much smaller than
lead frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Automotive: backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Part No. Material Emitted Color Lens Color
19-217/G7C-AN1P2/3T AlGaInP Brilliant Yellow Green Water Clear
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 2 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Package Outline Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 3 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Absolute Maximum Ratings (Ta=25℃)
Parameter Symbol Rating Unit
Reverse Voltage VR 5 V
Forward Current IF 25 mA
Operating Temperature Topr -40 ~ +85 ℃
Storage Temperature Tstg -40 ~ +90 ℃
Soldering Temperature Tsol 260 (for 5 seconds) ℃
Electrostatic Discharge ESD 2000 V
Power Dissipation Pd 60 mW
Peak Forward Current
(Duty 1/10 @1KHz) IFP 60 mA
Soldering Temperature Tsol Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 4 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Electro-Optical Characteristics (Ta=25℃)
Parameter Symbol Min. Typ. Max. Unit Condition
Luminous Intensity Iv 28.5 ----- 72.0 mcd
Peak Wavelength λp ---- 575 ---- nm
Dominant Wavelength λd 569.5 ---- 577.5 nm
Spectrum Radiation
Bandwidth △λ ---- 20 ---- nm
Viewing Angle 2θ1/2 ---- 120 ---- deg
Forward Voltage VF ---- 2.0 2.4 V
IF=20mA
Reverse Current IR ---- ---- 10 μA VR=5V
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.05V
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 5 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Bin Range Of Dom. Wavelength
Group Bin Min Max Unit Condition
C16 569.5 571.5
C17 571.5 573.5
C18 573.5 575.5
A
C19 575.5 577.5
nm IF=20mA
Bin Range Of Luminous Intensity
Bin Min Max Unit Condition
N1 28.5 36.0
N2 36.0 45.0
P1 45.0 57.0
P2 57.0 72.0
mcd IF=20mA
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 6 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Typical Electro-Optical Characteristics Curves
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 7 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 8 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Label Desiccant Label
Aluminum moisture-proof bag
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 9 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level：90%
LTPD：10%
No. Items Test Condition
Test
Hours/Cycles Sample
Size Ac/Re
1 Reflow Soldering
Temp. : 260℃±5℃
Min. 5sec. 6 Min. 22 PCS. 0/1
2 Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS. 0/1
3 Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS. 0/1
4 High Temperature
Storage Temp. : 100℃ 1000 Hrs. 22 PCS. 0/1
5 Low Temperature
Storage Temp. : -40℃ 1000 Hrs. 22 PCS. 0/1
6 DC Operating Life IF = 20 mA 1000 Hrs. 22 PCS. 0/1
7 High Temperature /
High Humidity 85℃/ 85%RH 1000 Hrs. 22 PCS. 0/1
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 10 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package : The LEDs should be kept at 30℃ or less and 70%RH or less(Floor life).
However, it's recommended that the LEDs should be used within 168 hours (7 days) after opening
the package. If unused LEDs remain, it should be stored in moisture proof packages.
2.4 After opening the package, the LEDs should be kept at 30℃ or less and 70%RH or less.
2.5 The LEDs should be used within 168 hours (7 days) after opening the package.
2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
EVERLIGHT ELECTRONICS CO.,LTD.
19-217/G7C-AN1P2/3T
Everlight Electronics Co., Ltd. http://www.everlight.com Rev. 1 Page: 11 of 11
Device No. : DSE-197- Prepared date: 05-Jul-2005 Prepared by: Ashley Kuo
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 280℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936
Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Fax: 886-2267-6244, 2267-6189, 2267-6306
Tucheng, Taipei 236, Taiwan, R.O.C http://www.everlight.com
