Not Recommended for New Designs VTM48EH040 x 025A00 (Formerly VIV0104THJ) VTMTM Current Multiplier S (R) C FEATURES * 40 Vdc to 3.3 Vdc 25 A current multiplier - Operating from standard 48 V or 24 V PRMTM regulators * High efficiency (>93%) reduces system power consumption * High density (167 A/in3) * "Half Chip" V* I ChipTM package enables surface mount, low impedance interconnect to system board * Contains built-in protection features against: - Overvoltage Overcurrent Short Circuit Overtemperature * Provides enable / disable control, internal temperature monitoring, current monitoring * ZVS / ZCS resonant Sine Amplitude Converter topology * Less than 50C temperature rise at full load in typical applications TYPICAL APPLICATIONS * High End Computing Systems * Automated Test Equipment * High Density Power Supplies * Communications Systems *0 US C NRTL US DESCRIPTION The V* I ChipTM current multiplier is a high efficiency (>93%) Sine Amplitude ConverterTM (SACTM) operating from a 26 to 55 Vdc primary bus to deliver an isolated output. The Sine Amplitude Converter offers a low AC impedance beyond the bandwidth of most downstream regulators, which means that capacitance normally at the load can be located at the input to the Sine Amplitude Converter. Since the K factor of the VTM48EH040T025A00 is 1/12, that capacitance value can be reduced by a factor of 144, resulting in savings of board area, materials and total system cost. The VTM48EH040T025A00 is provided in a V* I Chip package compatible with standard pick-and-place and surface mount assembly processes. The co-molded V*I Chip package provides enhanced thermal management due to large thermal interface area and superior thermal conductivity. With high conversion efficiency the VTM48EH040T025A00 increases overall system efficiency and lowers operating costs compared to conventional approaches. The VTM48EH040T025A00 enables the utilization of Factorized Power ArchitectureTM providing efficiency and size benefits by lowering conversion and distribution losses and promoting high density point of load conversion. VIN = 26 to 55 V IOUT = 25 A (NOM) VOUT = 2.2 to 4.6 V (NO LOAD) K= 1/12 PART NUMBERING PART NUMBER PRODUCT GRADE T = -40 to 125C VTM48EH040 x 025A00 M = -55 to 125C For Storage and Operating Temperatures see Section 6.0 General Characteristics Regulator PR PC TM IL Current Multiplier VC SG OS CD +Out -In -Out IM TM VTMTM PRMTM +In PC VC +In +Out -In -Out VIN L O A D (See Application Note AN:024) Factorized Power ArchitectureTM V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 1 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 1.0 ABSOLUTE MAXIMUM VOLTAGE RATINGS The absolute maximum ratings below are stress ratings only. Operation at or beyond these maximum ratings can cause permanent damage to the device. MIN MAX UNIT MIN MAX UNIT + IN to - IN . . . . . . . . . . . . . . . . . . . . . . . -1.0 60 VDC IM to - IN................................................. PC to - IN . . . . . . . . . . . . . . . . . . . . . . . . -0.3 20 VDC + IN / - IN to + OUT / - OUT (hipot)........ TM to -IN . . . . . . . . . . . . . . . . . . . . . . . . -0.3 7 VDC + IN / - IN to + OUT / - OUT (working)... VC to - IN . . . . . . . . . . . . . . . . . . . . . . . . -0.3 20 VDC + OUT to - OUT....................................... 0 -1.0 3.15 VDC 2250 VDC 60 VDC 10 VDC 2.0 ELECTRICAL CHARACTERISTICS Specifications apply over all line and load conditions unless otherwise noted; Boldface specifications apply over the temperature range of -40C < TJ < 125C (T-Grade); All other specifications are at TJ = 25C unless otherwise noted. ATTRIBUTE SYMBOL Input Voltage Range VIN VIN Slew Rate dVIN /dt VIN UV Turn Off VIN_UV CONDITIONS / NOTES No external VC applied VC applied No Load power dissipation PNL Inrush current peak IINRP Module latched shutdown, No external VC applied, IOUT = 25A VIN = 42 V VIN = 26 V to 55 V VIN = 42 V, TC = 25C VIN = 26 V to 55 V, TC = 25C VC enable, VIN = 42 V COUT = 4000 F, RLOAD = 134 m IIN_DC K VOUT K = VOUT / VIN, IOUT = 0 A VOUT = VIN * K - IOUT * ROUT, Section 11 DC input current Transfer ratio Output voltage Output current (average) Output current (peak) Output power (average) IOUT_AVG IOUT_PK POUT_AVG AMB Efficiency (ambient) HOT 20% Efficiency (hot) Efficiency (Over load range) Output resistance (Cold) Output resistance (Ambient) Output resistance (Hot) Switching frequency Output ripple frequency ROUT_COLD ROUT_AMB ROUT_HOT FSW FSW_RP Output voltage ripple VOUT_PP Output inductance (parasitic) LOUT_PAR Output capacitance (internal) COUT_INT Output capacitance (external) COUT_EXT PROTECTION OVLO Overvoltage lockout response time Output overcurrent trip Short circuit protection trip current Output overcurrent response time constant Short circuit protection response time Thermal shutdown setpoint TPEAK < 10 ms, IOUT_AVG 25 A IOUT_AVG 25 A VIN = 42 V, IOUT = 25 A VIN = 26 V to 55 V, IOUT = 25 A VIN = 42 V, IOUT = 12.5 A VIN = 42 V, TC = 100C, IOUT = 25 A 5 A < IOUT < 25 A TC = -40C, IOUT = 25 A TC = 25C, IOUT = 25 A TC = 100C, IOUT = 25 A Module latched shutdown TOVLO Effective internal RC filter IOCP ISCP 19 1.2 2.4 7.3 Effective internal RC filter (Integrative). TSCP From detection to cessation of switching (Instantaneous) MAX V/s 26.0 V 4.0 5.0 2.7 4.0 W 12 A 3 A V/V V A A W 25 37.5 115 90.5 88.0 90.4 90.0 81.0 4.2 5.0 5.8 1.50 3.00 55.5 VDC 92.4 % 92.3 91.8 5.3 6.2 7.3 1.65 3.30 6.4 7.4 8.8 1.80 3.60 % % m m m MHz MHz 220 400 mV 600 pH 68 F 57.2 4000 F 59.8 V 2.4 125 UNIT 55 55 1 1/12 30 40 TOCP TYP 26 0 COUT = 0 F, IOUT = 25 A, VIN = 42 V, 20 MHz BW, Section 12 Frequency up to 30 MHz, Simulated J-lead model VOUT = 3.3 V VTM Standalone Operation VIN pre-applied, VC enable VIN_OVLO+ TJ_OTP MIN 55 s 90 A A 6.6 ms 1 s 130 V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 135 C Rev. 2.0 5/2011 Page 2 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 3.0 SIGNAL CHARACTERISTICS Specifications apply over all line and load conditions unless otherwise noted; Boldface specifications apply over the temperature range of -40C < TJ < 125C (T-Grade); All other specifications are at TJ = 25C unless otherwise noted. * Used to wake up powertrain circuit. * A minimum of 12 V must be applied indefinitely for VIN < 26 V to ensure normal operation. * VC slew rate must be within range for a successful start. SIGNAL TYPE STATE Steady ATTRIBUTE VTM CONTROL : VC * PRM VC can be used as valid wake-up signal source. * VC voltage may be continuously applied; there will be minimal VC current drawn when VIN > 26 V and VC < 13. * Internal resistance used in adaptive loop compensation SYMBOL External VC voltage VVC_EXT VC current draw threshold VVC_TH VC current draw IVC VC internal resistor RVC-INT VC slew rate dVC/dt VC inrush current IINR_VC CONDITIONS / NOTES MIN Required for startup, and operation below 26 V. See Section 7. Low VC current draw for VIN >26 V VC = 13 V, VIN = 0 V VC = 13 V, VIN > 26 V VC = 16.5 V, VIN > 26 V 12 MAX UNIT 16.5 13 90 6 90 8.87 V 150 mA k V/s VC = 16.5 V, dVC/dt = 0.25 V/s 750 VIN pre-applied, PC floating, VC enable VC output turn-on delay TON 500 CPC = 0 F, COUT = 4000 F Transitional VC = 12 V to PC high, VIN = 0 V, 10 VC to PC delay TVC_PC 25 dVC/dt = 0.25 V/s Internal VC capacitance CVC_INT VC = 0 V 2.2 PRIMARY CONTROL : PC * The PC pin enables and disables the VTM. * Module will shutdown when pulled low with an impedance When held below 2 V, the VTM will be disabled. less than 400 . * PC pin outputs 5 V during normal operation. PC pin is equal to 2.5 V * In an array of VTMs, connect PC pin to synchronize startup. during fault mode given VIN > 26 V and VC > 12 V. * PC pin cannot sink current and will not disable other module * After successful start-up and under no fault condition, PC can be used as during fault mode. a 5 V regulated voltage source with a 2 mA maximum current. mA Start Up SIGNAL TYPE STATE ATTRIBUTE SYMBOL CONDITIONS / NOTES 0.02 V 0.25 ANALOG INPUT Required for proper startup; TYP MIN TYP PC voltage VPC 4.7 5.0 5.3 PC source current IPC_OP 2 ANALOG PC resistance (internal) RPC_INT Internal pull down resistor 50 150 400 OUTPUT PC source current IPC_EN 50 100 300 Start Up PC capacitance (internal) CPC_INT Section 7 50 PC resistance (external) RPC_EXT 60 PC voltage (enable) VPC_EN 2 2.5 3 Enable PC voltage (disable) VPC_DIS 2 Disable DIGITAL PC pull down current IPC_PD 5.1 INPUT / OUPUT PC disable time TPC_DIS_T 4 Transitional PC fault response time TFR_PC From fault to PC = 2 V 100 TEMPERATURE MONITOR : TM * The TM pin monitors the internal temperature of the VTM controller IC * The TM pin has a room temperature setpoint of 3 V (@27C) within an accuracy of 5C. and approximate gain of 10 mV/C. * Can be used as a "Power Good" flag to verify that the VTM is operating. STATE ANALOG OUTPUT Steady Disable DIGITAL OUTPUT (FAULT FLAG) Transitional ATTRIBUTE TM voltage TM source current TM gain SYMBOL VTM_AMB ITM ATM TM voltage ripple VTM_PP TM voltage TM resistance (internal) TM capacitance (external) TM fault response time VTM_DIS RTM_INT CTM_EXT TFR_TM CONDITIONS / NOTES TJ controller = 27C s F MAX UNIT Steady SIGNAL TYPE s V mA k A pF k V V mA s s MIN TYP MAX UNIT 2.95 3.00 3.05 100 V A mV/C 200 mV 50 50 V k pF s 10 CTM = 0 F, VIN = 42 V, IOUT = 25 A Internal pull down resistor From fault to TM = 1.5 V V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 120 25 0 40 10 Rev. 2.0 5/2011 Page 3 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 3.0 SIGNAL CHARACTERISTICS (CONT.) Specifications apply over all line and load conditions unless otherwise noted; Boldface specifications apply over the temperature range of -40C < TJ < 125C (T-Grade); All other specifications are at TJ = 25C unless otherwise noted. CURRENT MONITOR : IM * The nominal IM pin voltage varies between 0.2 V and 1.39 V representing the output current within 25% under all operating line temperature conditions between 50% and 100%. SIGNAL TYPE STATE ANALOG OUTPUT ATTRIBUTE IM voltage (no load) IM voltage (50%) IM voltage (full load) IM gain IM resistance (external) Steady * The IM pin provides a DC analog voltage proportional to the output current of the VTM. SYMBOL VIM_NL VIM_50% VIM_FL A IM RIM_EXT CONDITIONS / NOTES TC = 25C, VIN = 42 V, IOUT = 0 A TC = 25C, VIN = 42 V, IOUT = 12.5 A TC = 25C, VIN = 42 V, IOUT = 25 A TC = 25C, VIN = 42 V, IOUT > 12.5 A MIN TYP MAX UNIT 0.14 0.2 0.67 1.39 58 0.28 V V V mV/A M 2.5 4.0 TIMING DIAGRAM IOUT 6 7 ISSP IOCP 1 2 3 VC 4 8 d 5 b VVC-EXT a VOVLO VIN NL 26 V c e f VOUT TM VTM-AMB PC g 5V 3V a: VC slew rate (dVC/dt) b: Minimum VC pulse rate c: TOVLO d: TOCP e: Output turn on delay (TON) f: PC disable time (TPC_DIS_T) g: VC to PC delay (TVC_PC) 1. Initiated VC pulse 2. Controller start 3. VIN ramp up 4. VIN = VOVLO 5. VIN ramp down no VC pulse 6. Overcurrent 7. Start up on short circuit 8. PC driven low Notes: - Timing and voltage is not to scale - Error pulse width is load dependent V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 4 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 5.0 APPLICATION CHARACTERISTICS The following values, typical of an application environment, are collected at TC = 25C unless otherwise noted. See associated figures for general trend data. ATTRIBUTE SYMBOL No load power dissipation Efficiency (ambient) Efficiency (hot) Output resistance (ambient) Output resistance (hot) Output resistance (cold) PNL AMB HOT ROUT_AMB ROUT_HOT ROUT_COLD Output voltage ripple VOUT_PP VOUT Transient (positive) VOUT_TRAN+ VOUT Transient (negative) VOUT_TRAN- CONDITIONS / NOTES TYP UNIT VIN = 42 V VIN = 42 V, IOUT = 25 A VIN = 42 V, IOUT = 25 A, TC = 100C VIN = 42 V, IOUT = 25 A VIN = 42 V, IOUT = 25 A, TC = 100C VIN = 42 V, IOUT = 25 A, TC = -40C COUT = 0 F, IOUT = 25 A, VIN = 42 V, 20 MHz BW, Section 12 IOUT_STEP = 0 A TO 25A, VIN = 42 V, ISLEW > 10 A /us IOUT_STEP = 25 A to 0 A, VIN = 42 V ISLEW > 10 A /us 2.5 92.3 91.4 6.3 7.7 5.5 W % % m m m 229 mV 175 mV 175 mV Full Load Efficiency vs. Case Temperature No Load Power Dissipation vs. Line 94 Full Load Efficiency (%) 5 4 3 2 93 92 91 90 89 88 87 1 26 29 32 36 39 42 45 49 52 -40 55 -20 Input Voltage (V) -40C TCASE: 25C VIN : 100C 14 12 10 80 8 PD 70 6 65 4 60 2 0 55 5 7.5 10 12.5 15 17.5 26 V 42 V 55 V 26 V 80 100 42 V 55 V 20 22.5 14 12 85 10 80 8 PD 75 6 70 4 65 2 0 60 25 0 2.5 Output Current (A) VIN: 26 V 90 Efficiency (%) 90 2.5 60 95 Power Dissipation (W) Efficiency (%) 16 0 40 Efficiency & Power Dissipation 25C Case Efficiency & Power Dissipation -40C Case 95 75 20 Figure 2 -- Full load efficiency vs. temperature Figure 1 -- No load power dissipation vs. VIN 85 0 Case Temperature (C) Power Dissipation (W) No Load Power Dissipation (W) 6 5 7.5 10 12.5 15 17.5 20 22.5 25 Output Current (A) 42 V Figure 3 -- Efficiency and power dissipation at -40C 55 V VIN: 26 V 42 V 55 V 26 V 42 V 55 V Figure 4 -- Efficiency and power dissipation at 25C V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 5 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 Efficiency & Power Dissipation 100C Case 85 8 12 7.5 10 8 80 75 6 PD 70 4 65 2 60 0 7 Rout (m) Efficiency (%) 90 ROUT vs. TCASE at VIN = 42 V 14 Power Dissipation (W) 95 6.5 6 5.5 5 4.5 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 4 25 -40 -20 0 Output Current (A) 26 V VIN: 42 V 55 V 26 V 42 V 55 V 40 60 80 100 I OUT : 12 A 25 A Figure 6 -- ROUT vs. temperature Figure 5 -- Efficiency and power dissipation at 100C Ripple vs. Load IM Voltage vs. Load at VIN = 42 V 250 2 225 1.75 1.5 200 IM (V) Ripple (mV pk-pk) 20 Case Temperature (C) 175 1.25 1 0.75 150 0.5 125 0.25 100 0 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 0 2.5 5 Load Current (A) 10 12.5 15 17.5 20 22.5 25 80 100 Load Current (A) 42 V V IN : 7.5 TCASE: Figure 7 -- VRIPPLE vs. IOUT ; No external COUT. Board mounted module, scope setting : 20 MHz analog BW -40C 25C 100C Figure 8 -- IM voltage vs. load IM Voltage vs. TCASE & Line IM Voltage vs. Load 25C Case 2 1.75 1.5 1.75 1 IM (V) IM (V) 1.25 0.75 0.5 1.5 1.25 0.25 1 0 0 2.5 5 7.5 10 12.5 15 17.5 20 22.5 25 -40 -20 0 26 V Figure 9 -- IM voltage vs. load 42 V 40 60 TCASE (C) Load Current (A) VIN : 20 55 V VIN 26 V 48 V 55 V Figure 10 -- Full load IM voltage vs. TCASE V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 6 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 Safe Operating Area 40 Output Current (A) 35 10 ms Max 30 25 20 Continuous 15 10 5 0 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 Output Voltage (V) Figure 11 -- Safe operating area Figure 12 -- Full load ripple, 100 F CIN; No external COUT. Board mounted module, scope setting : 20 MHz analog BW Figure 13 -- Start up from application of VIN ; VC pre-applied COUT = 0 F Figure 14 -- Start up from application of VC; VIN pre-applied COUT = 0 F Figure 15 -- 0 A - 25 A transient response: CIN = 100 F, no external COUT Figure 16 -- 25 A - 0 A transient response: CIN = 100 F, no external COUT V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 7 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 6.0 GENERAL CHARACTERISTICS Specifications apply over all line and load conditions unless otherwise noted; Boldface specifications apply over the temperature range of -40C < TJ < 125C (T-Grade); All Other specifications are at TJ = 25C unless otherwise noted. ATTRIBUTE SYMBOL MECHANICAL Length Width Height Volume Weight L W H Vol W CONDITIONS / NOTES TYP MAX UNIT 21.7 / [0.85] 16.4 / [0.64] 6.48 / [0.255] 22.0 / [0.87] 16.5 / [0.65] 6.73 / [0.265] 2.44 / [0.150] 8.0 / 0.28 22.3 / [0.88] 16.6 / [0.66] 6.98 / [0.275] mm/[in] mm/[in] mm/[in] cm3/[in3] g/[oz] No heat sink Nickel Palladium Gold Lead finish MIN 0.51 0.02 0.003 2.03 0.15 0.051 -40 -55 125 125 C C Ws/C 3 lbs 125 125 C C m THERMAL Operating temperature TJ VTM48EH040T025A00 (T-Grade) VTM48EH040M025A00 (M-Grade) Thermal capacity 5 ASSEMBLY Peak compressive force Applied to case (Z-axis) Supported by J-lead only Storage temperature TST ESDHBM ESD withstand ESDMM VTM48EH040T025A00 (T-Grade) VTM48EH040M025A00 (M-Grade) Human Body Model, "JEDEC JESD 22-A114C.01" Machine Model, "JEDEC JESD 22-A115-A" 2.5 -40 -65 1500 VDC 400 SOLDERING MSL 5 MSL 6, TOB = 4hrs Peak temperature during reflow Peak time above 183C Peak heating rate during reflow Peak cooling rate post reflow SAFETY Working voltage (IN - OUT) Isolation voltage (hipot) Isolation capacitance Isolation resistance MTBF Agency approvals / standards 1.5 1.5 VIN_OUT VHIPOT CIN_OUT RIN_OUT Unpowered Unit MIL HDBK 217, 25C, Ground Benign cTUVus cURus CE Mark RoHS 6 of 6 2250 1350 10 1750 4.5 V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 225 245 150 3 6 C C s C/s C/s 60 VDC VDC pF M 2150 MHrs Rev. 2.0 5/2011 Page 8 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 7.0 USING THE CONTROL SIGNALS VC, PC, TM, IM The VTM Control (VC) pin is an input pin which powers the internal VCC circuitry when within the specified voltage range of 12 V to 16.5 V. This voltage is required in order for the VTM module to start, and must be applied as long as the input is below 26 V. In order to ensure a proper start, the slew rate of the applied voltage must be within the specified range. Some additional notes on the using the VC pin: * In most applications, the VTMTM module will be powered by an upstream PRM which provides a 10 ms VC pulse during startup. In these applications the VC pins of the PRM and VTM should be tied together. * The VC voltage can be applied indefinitely allowing for continuous operation down to 0 VIN. * The fault response of the VTM module is latching. A positive edge on VC is required in order to restart the unit. If VC is continuously applied the PC pin may be toggled to restart the module. Primary Control (PC) pin can be used to accomplish the following functions: * Delayed start: Upon the application of VC, the PC pin will source a constant 100 A current to the internal RC network. Adding an external capacitor will allow further delay in reaching the 2.5 V threshold for module start. * Auxiliary voltage source: Once enabled in regular operational conditions (no fault), each VTM PC provides a regulated 5 V, 2 mA voltage source. * Output disable: PC pin can be actively pulled down in order to disable the module. Pull down impedance shall be lower than 400 . * Fault detection flag: The PC 5 V voltage source is internally turned off as soon as a fault is detected. It is important to notice that PC doesn't have current sink capability. Therefore, in an array, PC line will not be capable of disabling neighboring modules if a fault is detected. * Fault reset: PC may be toggled to restart the unit if VC is continuously applied. Temperature Monitor (TM) pin provides a voltage proportional to the absolute temperature of the converter control IC. It can be used to accomplish the following functions: * Monitor the control IC temperature: The temperature in Kelvin is equal to the voltage on the TM pin scaled by 100. (i.e. 3.0 V = 300 K = 27C). If a heat sink is applied, TM can be used to thermally protect the system. * Fault detection flag: The TM voltage source is internally turned off as soon as a fault is detected. For system monitoring purposes (microcontroller interface) faults are detected on falling edges of TM signal. Current Monitor (IM) pin provides a voltage proportional to the output current of the VTM module. The nominal voltage will vary between 0.2 V and 1.39 V over the output current range of the module (See Figures 8-10). The accuracy of the IM pin will be within 25% under all line and temperature conditions between 50% and 100% load. 8.0 STARTUP BEHAVIOR Depending on the sequencing of the VC with respect to the input voltage, the behavior during startup will vary as follows: * Normal Operation (VC applied prior to VIN): In this case the controller is active prior to ramping the input. When the input voltage is applied, the VTM output voltage will track the input (See Figure 13). The inrush current is determined by the input voltage rate of rise and output capacitance. If the VC voltage is removed prior to the input reaching 26 V, the VTM module may shut down. * Stand Alone Operation (VC applied after VIN ): In this case the module output will begin to rise upon the application of the VC voltage (See Figure 14). The Adaptive Soft Start circuit (See Section 10) may vary the ouput rate of rise in order to limit the inrush current to it's maximum level. When starting into high capacitance, or a short, the output current will be limited for a maximum of 900 sec. After this period, the adaptive soft start circuit will time out and the module may shut down. No restart will be attempted until VC is re-applied, or PC is toggled. The maximum output capacitance is limited to 4000 F in this mode of operation to ensure a sucessful start. 9.0 THERMAL CONSIDERATIONS V* I ChipTM products are multi-chip modules whose temperature distribution varies greatly for each part number as well as with the input / output conditions, thermal management and environmental conditions. Maintaining the top of the VTM48EH040T025A00 case to less than 100C will keep all junctions within the V* I Chip below 125C for most applications. The percent of total heat dissipated through the top surface versus through the J-lead is entirely dependent on the particular mechanical and thermal environment. The heat dissipated through the top surface is typically 60%. The heat dissipated through the J-lead onto the PCB board surface is typically 40%. Use 100% top surface dissipation when designing for a conservative cooling solution. It is not recommended to use a V* I Chip module for an extended period of time at full load without proper heat sinking. V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 9 of 16 v i c o r p o w e r. c o m v i c o r p o w e r. c o m PC -VIN VC +VIN 560 pF 2.5 V Rvc Enable 100 uA 150 K 1.5 k 2.5 V PC Pull-Up & Source 10.5 V Buck Regulator Supply 18 V CIN 5V Enable 2 mA OVLO UVLO VIN Adaptive Soft Start Gate Drive Supply Enable Fault Logic Enable Modulator Q2 Primary Current Sensing Primary Gate Drive Q1 Lr Over Temperature Protection Cr Primary Stage & Resonant Tank Slow current limit Fast current limit Overcurrent Protection Secondary Gate Drive Power Transformer VREF (130C 5C) Vref C2 C1 40 K Synchronous Rectification Q4 3 V max. 240 A max. Temperature dependent voltage source Q3 COUT TM IM -VOUT +VOUT Not Recommended for New Designs VTM48EH040 x 025A00 10.0 VTMTM MODULE BLOCK DIAGRAM V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 10 of 16 Not Recommended for New Designs VTM48EH040 x 025A00 11.0 SINE AMPLITUDE CONVERTERTM POINT OF LOAD CONVERSION function of input voltage and output current. A small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving power density. The VTM48EH040T025A00 SAC can be simplified into the following model: The Sine Amplitude ConverterTM (SACTM) uses a high frequency resonant tank to move energy from input to output. (The resonant tank is formed by Cr and leakage inductance Lr in the power transformer windings as shown in the VTMTM Module Block Diagram. See Section 10). The resonant LC tank, operated at high frequency, is amplitude modulated as 150 pH IOUT IOUT LLININ== 1.7 5 nH nH OUT RROUT 6.2 m + R RCIN CIN 6.3 m CCININ 900 nF RRCOUT COUT 350 m V*I 1/12 * IOUT VIN V IN LOUT = 600 pH + + - - + 330 1/12 * VIN COUT COUT IIQQ 68 F VVOUT OUT 0.057 A K - - Figure 17 -- V*I ChipTM module AC model At no load: VOUT = VIN * K (1) ROUT = 0 and IQ = 0 A, Eq. (3) now becomes Eq. (1) and is essentially load independent. A resistor R is now placed in series with VIN as shown in Figure 18. K represents the "turns ratio" of the SAC. Rearranging Eq (1): R V K = OUT VIN (2) VVin IN + - SACTM SAC = 1/32 1/32 KK = Vout V OUT In the presence of load, VOUT is represented by: VOUT = VIN * K - IOUT * ROUT (3) The relationship between VIN and VOUT becomes: and IOUT is represented by: IOUT = IIN - IQ K Figure 18 -- K = 1/32 Sine Amplitude ConverterTM with series input resistor (4) ROUT represents the impedance of the SAC, and is a function of the RDSON of the input and output MOSFETs and the winding resistance of the power transformer. IQ represents the quiescent current of the SAC control and gate drive circuitry. The use of DC voltage transformation provides additional interesting attributes. Assuming for the moment that VOUT = (VIN - IIN * R) * K (5) Substituting the simplified version of Eq. (4) (IQ is assumed = 0 A) into Eq. (5) yields: VOUT = VIN * K - IOUT * R * K2 V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 (6) Rev. 2.0 5/2011 Page 11 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 This is similar in form to Eq. (3), where ROUT is used to represent the characteristic impedance of the SACTM. However, in this case a real R on the input side of the SAC is effectively scaled by K2 with respect to the output. Assuming that R = 1 , the effective R as seen from the secondary side is 0.98 m, with K = 1/32 as shown in Figure 18. A similar exercise should be performed with the additon of a capacitor, or shunt impedance, at the input to the SAC. A switch in series with VIN is added to the circuit. This is depicted in Figure 19. S VVin IN + - C SACTM SAC K = 1/32 K = 1/32 VVout OUT Figure 19 -- Sine Amplitude ConverterTM with input capacitor A change in VIN with the switch closed would result in a change in capacitor current according to the following equation: IC(t) = C dVIN dt Low impedance is a key requirement for powering a highcurrent, low-voltage load efficiently. A switching regulation stage should have minimal impedance, while simultaneously providing appropriate filtering for any switched current. The use of a SAC between the regulation stage and the point of load provides a dual benefit, scaling down series impedance leading back to the source and scaling up shunt capacitance (or energy storage) as a function of its K factor squared. However, these benefits are not useful if the series impedance of the SAC is too high. The impedance of the SAC must be low well beyond the crossover frequency of the system. A solution for keeping the impedance of the SAC low involves switching at a high frequency. This enables magnetic components to be small since magnetizing currents remain low. Small magnetics mean small path lengths for turns. Use of low loss core material at high frequencies reduces core losses as well. The two main terms of power loss in the VTMTM module are: - No load power dissipation (PNL ): defined as the power used to power up the module with an enabled power train at no load. - Resistive loss (ROUT): refers to the power loss across the VTM current multiplier modeled as pure resistive impedance. PDISSIPATED = PNL + PROUT (7) (10) Therefore, POUT = PIN - PDISSIPATED = PIN - PNL - PROUT Assume that with the capacitor charged to VIN, the switch is opened and the capacitor is discharged through the idealized SAC. In this case, IC = IOUT * K (11) The above relations can be combined to calculate the overall module efficiency: (8) = (9) = POUT = PIN - PNL - PROUT PIN PIN (12) Substituting Eq. (1) and (8) into Eq. (7) reveals: IOUT = C K2 * dVOUT dt Writing the equation in terms of the output has yielded a K2 scaling factor for C, this time in the denominator of the equation. For a K factor less than unity, this results in an effectively larger capacitance on the output when expressed in terms of the input. With a K=1/32 as shown in Figure 19, C=1 F would effectively appear as C=1024 F when viewed from the output. VIN * IIN - PNL - (IOUT)2 * ROUT VIN * IIN = 1- ( ) PNL + (IOUT)2 * ROUT VIN * IIN V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 12 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 12.0 INPUT AND OUTPUT FILTER DESIGN A major advantage of a SACTM system versus a conventional PWM converter is that the former does not require large functional filters. The resonant LC tank, operated at extreme high frequency, is amplitude modulated as a function of input voltage and output current and efficiently transfers charge through the isolation transformer. A small amount of capacitance embedded in the input and output stages of the module is sufficient for full functionality and is key to achieving high power density. This paradigm shift requires system design to carefully evaluate external filters in order to: 1.Guarantee low source impedance. To take full advantage of the VTMTM module dynamic response, the impedance presented to its input terminals must be low from DC to approximately 5 MHz. Input capacitance may be added to improve transient performance or compensate for high source impedance. 2.Further reduce input and /or output voltage ripple without sacrificing dynamic response. Given the wide bandwidth of the VTM module, the source response is generally the limiting factor in the overall system response. Anomalies in the response of the source will appear at the output of the module multiplied by its K factor. 3.Protect the module from overvoltage transients imposed by the system that would exceed maximum ratings and cause failures. The V*I ChipTM module input/output voltage ranges must not be exceeded. An internal overvoltage lockout function prevents operation outside of the normal operating input range. Even during this condition, the powertrain is exposed to the applied voltage and power MOSFETs must withstand it. 13.0 CAPACITIVE FILTERING CONSIDERATIONS FOR A SINE AMPLITUDE CONVERTER It is important to consider the impact of adding input and output capacitance to a Sine Amplitude ConverterTM on the system as a whole. Both the capacitance value, and the effective impedance of the capacitor must be considered. A Sine Amplitude Converter has a DC ROUT value which has already been discussed in section 11. The AC ROUT of the SAC contains several terms: * Resonant tank impedance * Input lead inductance and internal capacitance * Output lead inductance and internal capacitance The values of these terms are shown in the behavioral model in section 11. It is important to note on which side of the transformer these impedances appear and how they reflect across the transformer given the K factor. The overall AC impedance varies from model to model but for most models it is dominated by DC ROUT value from DC to beyond 500 KHz. The behavioral model in section 11 should be used to approximate the AC impedance of the specific model. Any capacitors placed at the output of the VTM module reflect back to the input of the module by the square of the K factor (Eq. 9) with the impedance of the module appearing in series. It is very important to keep this in mind when using a PRMTM regulator to power the VTMTM. Most PRM regulators have a limit on the maximum amount of capacitance that can be applied to the output. This capacitance includes both the regulator output capacitance and the current multiplier output capacitance reflected back to the input. In PRM regulator remote sense applications, it is important to consider the reflected value of VTM current multiplier output capacitance when designing and compensating the PRM regulator control loop. Capacitance placed at the input of the VTM module appear to the load reflected by the K factor, with the impedance of the VTM module in series. In step-down VTM ratios, the effective capacitance is increased by the K factor. The effective ESR of the capacitor is decreased by the square of the K factor, but the impedance of the VTM module appears in series. Still, in most step-down VTM modules an electrolytic capacitor placed at the input of the module will have a lower effective impedance compared to an electrolytic capacitor placed at the output. This is important to consider when placing capacitors at the output of the current multiplier. Even though the capacitor may be placed at the output, the majority of the AC current will be sourced from the lower impedance, which in most cases will be the VTM current multiplier. This should be studied carefully in any system design using a VTM current multiplier. In most cases, it should be clear that electrolytic output capacitors are not necessary to design a stable, wellbypassed system. V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 13 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 14.0 CURRENT SHARING The SACTM topology bases its performance on efficient transfer of energy through a transformer without the need of closed loop control. For this reason, the transfer characteristic can be approximated by an ideal transformer with some resistive drop and positive temperature coefficient. This type of characteristic is close to the impedance characteristic of a DC power distribution system, both in behavior (AC dynamic) and absolute value (DC dynamic). When connected in an array with the same K factor, the VTMTM module will inherently share the load current with parallel units, according to the equivalent impedance divider that the system implements from the power source to the point of load. Some general recommendations to achieve matched array impedances: * Dedicate common copper planes within the PCB to deliver and return the current to the modules. * Provide the PCB layout as symmetric as possible. * Apply same input / output filters (if present) to each unit. 16.0 REVERSE OPERATION The VTM48EH040T025A00 is capable of reverse operation. If a voltage is present at the output which satisfies the condition VOUT > VIN * K at the time the VC voltage is applied, or after the unit has started, then energy will be transferred from secondary to primary. The input to output ratio will be maintained. The VTM48EH040T025A00 will continue to operate in reverse as long as the input and output are within the specified limits. The VTM48EH040T025A00 has not been qualified for continuous operation (>10 ms) in the reverse direction. For further details see AN:016 Using BCMTM Bus Converters in High Power Arrays. VIN ZIN_EQ1 VTMTM1 ZOUT_EQ1 VOUT RO_1 ZIN_EQ2 VTMTM2 ZOUT_EQ2 RO_2 + - DC Load ZIN_EQn VTMTMn ZOUT_EQn RO_n Figure 20 -- VTMTM module array 15.0 FUSE SELECTION In order to provide flexibility in configuring power systems V* I ChipTM products are not internally fused. Input line fusing of V* I Chip products is recommended at system level to provide thermal protection in case of catastrophic failure. The fuse shall be selected by closely matching system requirements with the following characteristics: * Current rating (usually greater than maximum VTM module current) * Maximum voltage rating (usually greater than the maximum possible input voltage) * Ambient temperature * Nominal melting I2t V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 14 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 17.1 MECHANICAL DRAWING mm (inch) NOTES: mm 2. DIMENSIONS ARE inch . UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE: 3. .X / [.XX] = +/-0.25 / [.01]; .XX / [.XXX] = +/-0.13 / [.005] 4. PRODUCT MARKING ON TOP SURFACE DXF and PDF files are available on vicorpower.com 17.2 RECOMMENDED LAND PATTERN 4 3 2 1 A +Out +In B C D E F G H J K -Out L M IM TM VC PC -In Bottom View NOTES: 3. .X / [.XX] = +/-0.25 / [.01]; .XX / [.XXX] = +/-0.13 / [.005] mm 2. DIMENSIONS ARE inch . UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE: 4. PRODUCT MARKING ON TOP SURFACE DXF and PDF files are available on vicorpower.com Signal Name Designation +In -In IM TM VC PC +Out -Out A1-B1, A2-B2 L1-M1, L2-M2 E1 F2 G1 H2 A3-D3, A4-D4 J3-M3, J4-M4 17.3 RECOMMENDED HEAT SINK PUSH PIN LOCATION Notes: 1. Maintain 3.50 (0.138) Dia. keep-out zone free of copper, all PCB layers. 2. (A) minimum recommended pitch is 24.00 (0.945) this provides 7.50 (0.295) component edge-to-edge spacing, and 0.50 (0.020) clearance between Vicor heat sinks. (B) Minimum recommended pitch is 25.50 (1.004). This provides 9.00 (0.354) component edge-to-edge spacing, and 2.00 (0.079) clearance between Vicor heat sinks. 3. V*I ChipTM module land pattern shown for reference only, actual land pattern may differ. Dimensions from edges of land pattern to push-pin holes will be the same for all half size V*I Chip Products. 4. RoHS compliant per CST-0001 latest revision. 5. Unless otherwise specified: Dimensions are mm (inches) tolerances are: x.x (x.xx) = 0.13 (0.01) x.xx (x.xxx) = 0.13 (0.005) 6. Plated through holes for grounding clips (33855) shown for reference. Heat sink orientation and device pitch will dictate final grounding solution. (NO GROUNDING CLIPS) (WITH GROUNDING CLIPS) V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 15 of 16 v i c o r p o w e r. c o m Not Recommended for New Designs VTM48EH040 x 025A00 Warranty Vicor products are guaranteed for two years from date of shipment against defects in material or workmanship when in normal use and service. This warranty does not extend to products subjected to misuse, accident, or improper application or maintenance. Vicor shall not be liable for collateral or consequential damage. This warranty is extended to the original purchaser only. EXCEPT FOR THE FOREGOING EXPRESS WARRANTY, VICOR MAKES NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Vicor will repair or replace defective products in accordance with its own best judgement. For service under this warranty, the buyer must contact Vicor to obtain a Return Material Authorization (RMA) number and shipping instructions. Products returned without prior authorization will be returned to the buyer. The buyer will pay all charges incurred in returning the product to the factory. Vicor will pay all reshipment charges if the product was defective within the terms of this warranty. Information published by Vicor has been carefully checked and is believed to be accurate; however, no responsibility is assumed for inaccuracies. Vicor reserves the right to make changes to any products without further notice to improve reliability, function, or design. Vicor does not assume any liability arising out of the application or use of any product or circuit; neither does it convey any license under its patent rights nor the rights of others. Vicor general policy does not recommend the use of its components in life support applications wherein a failure or malfunction may directly threaten life or injury. Per Vicor Terms and Conditions of Sale, the user of Vicor components in life support applications assumes all risks of such use and indemnifies Vicor against all damages. Vicor's comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor's Terms and Conditions of Sale, which are available upon request. Specifications are subject to change without notice. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. Interested parties should contact Vicor's Intellectual Property Department. The products described on this data sheet are protected by the following U.S. Patents Numbers: 5,945,130; 6,403,009; 6,710,257; 6,911,848; 6,930,893; 6,934,166; 6,940,013; 6,969,909; 7,038,917; 7,145,186; 7,166,898; 7,187,263; 7,202,646; 7,361,844; D496,906; D505,114; D506,438; D509,472; and for use under 6,975,098 and 6,984,965. Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 email Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com V*I CHIP CORP. (A VICOR COMPANY) 25 FRONTAGE RD. ANDOVER, MA 01810 800-735-6200 Rev. 2.0 5/2011 Page 16 of 16 v i c o r p o w e r. c o m