AMSC N/A FSC 5935
MIL-DTL-83513/3J
w/AMENDMENT 3
6 July 2016
SUPERSEDING
MIL-DTL-83513/3J
w/AMENDMENT 2
4 September 2013
DETAIL SPECIFICATION SHEET
CONNECTORS, ELECTRICAL, RECTANGUL AR, PLUG, MICROMINIATURE,
POLARIZED SHELL, PIN CONTACTS, CLASS M, CRIMP TYPE
This specification is approved for use by all Departments and
Agencies of the Department of Defense.
The requirements for acquiring the product described herein shall consist of this specification sheet and
MIL-DTL-83513.
FIGURE 1. Connector, plug, .050 spacing.
INCH-POUND
MIL-DTL-83513/3J
w/AMENDMENT 3
2
FIGURE 1. Connector, plug, .050 spacing - Continued.
MIL-DTL-83513/3J
w/AMENDMENT 3
3
FIGURE 1. Connector, plug, .050 spacing - Continued.
MIL-DTL-83513/3J
w/AMENDMENT 3
4
Number
of
cavities
A .010
(.25)
B BSC
C +.010
-.018
+(.25)
-(.46)
D BSC
Configuration
letter
9
.775
(19.69)
.3338
(8.479)
.390
(9.91)
.565
(14.35)
A
15
.925
(23.50)
.4838
(12.289)
.540
(13.72)
.715
(18.16)
A
21
1.075
(27.31)
.6338
(16.099)
.690
(17.53)
.865
(21.97)
A
25
1.175
(29.85)
.7338
(18.639)
.790
(20.07)
.965
(24.51)
A
31
1.325
(33.66)
.8838
(22.449)
.940
(23.88)
1.115
(28.32)
A
37
1.475
(37.47)
1.0338
(26.259)
1.090
(27.69)
1.265
(32.13)
A
51
1.425
(36.20)
.9838
(24.989)
1.040
(26.42)
1.215
(30.86)
B
100
2.160
(54.86)
1.3838
(35.149)
1.432
(36.37)
1.800
(45.72)
C
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are +.005 (0.13 mm).
4. Metric equivalents are in parentheses or columns.
5 Point from which the lead length is measured.
6. Shell shall be flush to insulator within ±.005 (0.13 mm).
7. Dimension line at point D locates the point of intersection of the two adjacent side of the receptacle
interface.
8. 26 AWG wire is the maximum wire size that can be used in the solder cup.
FIGURE 1. Connector, plug, .050 spacing - Continued.
Inches
Inches
mm
.0015
.094
2.39
.002
.1139
2.893
.003
.117
2.97
.0038
.123
3.12
.004
.145
3.68
.005
.150
3.81
.007
.173
4.39
.010
.181
4.60
.014
.182
4.62
.020
.183
4.65
.022
.224
5.69
.025
.2278
5.786
.036
.267
6.78
.050
.270
6.86
.0669
.298
7.57
.0671
.310
7.87
.089
.341
8.66
.090
.360
9.14
.0924
.384
9.75
.093
.406
10.31
MIL-DTL-83513/3J
w/AMENDMENT 3
5
NOTES:
1. Engaging face of pin insert shown.
2. Cavity identification numbers are for reference only and do not appear on part.
FIGURE 2. Ins er t arr ang e ment.
MIL-DTL-83513/3J
w/AMENDMENT 3
6
REQUIREMENTS:
Dimensions and configurations: See figure 1. This specification sheet describes the pin side of a
rectangular metal shell connector. This connector uses reverse gender contact, i.e., the live pin
recessed in the insulator with the static socket protruding from a shrouded interface.
Materials and finish:
Shell: The requirements for shell materials shall be in accordance with MIL-DTL-83513.
Contact identification: See figure 2 for contact layout identification.
Contact connection: The pin contact (being recessed in the insulator) is normally connected to the live
side of the circuit.
Current rating, maximum: 3 amperes per contact.
Mounting and mating hardware: Mounting hardware is to be ordered separately. Insert arrangements
A through G, are in accordanc e with MIL-DTL-83513/5, configurations A and B. Insert arrangement H,
are in accordance with MIL-DTL-83513/5, configuration C.
Mating hardware torque: Mating hardware torque shall be in accordance with MIL-DTL-83513/5.
Mating plug: Mating plug is in accor danc e with MIL-DTL-83513/2 or MIL-DTL-83513/4.
MIL-DTL-83513/3J
w/AMENDMENT 3
7
Part or Identifying Number (PIN): Consists of the letter M, the basic number of the specification sheet, a
letter from the insert column and the shell finish.
M83513/03 -
A
01
C
Specification sheet
number
Insert
arrangement
Wire
type
Shell finish
(Interface critical)
(see figure 2)
A = 9
A = Pure electrod epo sit ed
B = 15
aluminum
C = 21
C = Cadmium
D = 25
K = Zinc nickel
E = 31
N = elect roless nickel
F = 37
(space applications)
G = 51
P = Passivated stainless steel
H = 100
T = Nickel fluorocarbon polymer
Wire
type 1/
Wire length
Wire specification (inches)
Notes
01 =
M22759/11-26-9
18
2/, 3/
02 =
M22759/11-26-9
36
2/, 3/
03 =
M22759/11-26-( )
18
3/, 4/, 5/
04 =
M22759/11-26-( )
36
3/, 4/, 5/
05 =
A-A-59551, t ype S, 25 AW G ,
gold plated 10 micro inches
0.5
6/, 7/
06 =
A-A-59551, t ype S, 25 AW G ,
gold plated 10 micro inches
1.0
6/, 7/
07 =
A-A-59551, t ype S, 25 AW G ,
tin plated 100 micro inches
0.5
6/, 7/, 9/
08 =
A-A-59551, t ype S, 25 AW G ,
tin plated 100 micro inches
1.0
6/, 7/, 9/
09 =
M22759/33-26-9
18
3/, 8/
10 =
M22759/33-26-9
36
3/, 8/
11 =
M22759/33-26-( )
18
3/, 4/, 5/, 8/
12 =
M22759/33-26-( )
36
3/, 4/, 5/, 8/
13 =
M22759/11-26-9
72
2/, 3/
14 =
M22759/11-26-( )
72
3/, 4/, 5/
15 =
M22759/33-26-9
72
3/, 8/
16 =
M22759/33-26-( )
72
3/, 4/, 5/, 8/
17 =
04035-26A-9
18
2/, 3/
18 =
04035-26A-9
36
2/, 3/
19 =
04035-26A-9
72
2/, 3/
20 =
04035-26A-( )
18
3/, 4/, 5/
21 =
04035-26A-( )
36
3/, 4/, 5/
22 =
04035-26A-( )
72
3/, 4/, 5/
See notes at end of wire type.
MIL-DTL-83513/3J
w/AMENDMENT 3
8
PIN – Continued.
01
Wire
type
Wire
type 1/
Wire length
Wire specification (inches)
Notes
23 =
M22759/47-26-9
18
2/, 3/
24 =
M22759/47-26-9
36
2/, 3/
25 =
M22759/47-26-9
72
2/, 3/
26 =
M22759/47-26-( )
18
3/, 4/, 5/
27 =
M22759/47-26-( )
36
3/, 4/, 5/
28 =
M22759/47-26-( )
72
3/, 4/, 5/
29 =
M22759/48-26-9
18
2/, 3/
30 =
M22759/48-26-9
36
2/, 3/
31 =
M22759/48-26-9
72
2/, 3/
32 =
M22759/48-26-( )
18
3/, 4/, 5/
33 =
M22759/48-26-( )
36
3/, 4/, 5/
34 =
M22759/48-26-( )
72
3/, 4/, 5/
35 =
M22759/49-26-9
18
2/, 3/
36 =
M22759/49-26-9
36
2/, 3/
37 =
M22759/49-26-9
72
2/, 3/
38 =
M22759/49-26-( )
18
3/, 4/, 5/
39 =
M22759/49-26-( )
36
3/, 4/, 5/
40 =
M22759/49-26-( )
72
3/, 4/, 5/
41 =
M22759/50-26-9
18
2/, 3/
42 =
M22759/50-26-9
36
2/, 3/
43 =
M22759/50-26-9
72
2/, 3/
44 =
M22759/50-26-( )
18
3/, 4/, 5/
45 =
M22759/50-26-( )
36
3/, 4/, 5/
46 =
M22759/50-26-( )
72
3/, 4/, 5/
1/ These connectors have leads attached of which wire type, wire size, wire color, and lead length are
specif ied in the PIN.
2/ For connectors with shell finish N intended for space applications, wire shall be M22759/47-26-9 or
M22759/33-26-9.
3/ Lead length tolerance +1.0, -0.0 inch.
4/ For connectors with shell finish N intended for space applications, wire shall be M22759/47-26-() or
M22759/33-26-( ).
5/ Color coding in accordance with MIL-STD-681, system I, except the appropriate color code shall be
the individual contact cavity number minus 1 for contact positions 1 through 10 only, 11 through 20,
etc. For example:
Pin number
Identification
4
3
9
8
21
0
31
0
77
6
100
9
MIL-DTL-83513/3J
w/AMENDMENT 3
9
6/ Lead length tolerance +0.2, -0.0 inch.
7/ Contact and wire may be a single piece design.
8/ Corrosion has been experienced on M83513 connectors that are prewired with S AE A S2 2 759 /33
and stored in a sealed environment. CAUTION SHOULD BE EXCERCISED WHEN USING THIS
WIRE.
9/ Pure tin. The use of pure tin is prohibited. Tin content used in connector materials shall not exceed
97 percent, and an alloy material shall be chosen to inhibit the growth of tin whiskers.
Amendment notations. The margins of this specification are marked with vertical lines to indicate
modifications generated by this amendment. This was done as a convenience only and the Government
assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are
cautioned to evaluate the requirements of this document based on the entire content irrespective of the
marginal notations.
Referenced documents. In addition to MIL-DTL-83513, this document references the following:
A-A-59551
MIL-DTL-83513/2
MIL-DTL-83513/4
MIL-DTL-83513/5
MIL-STD-681
SAE AS2 275 9/ 3 3
CONCLUDING MATERIAL
Custodians: Preparing activity:
Army - CR DLA - CC
Navy - EC
Air Force - 85 (Project: 5935-2016-094)
NASA - NA
DLA - CC
Revie w ac t i vit ies :
Army - AT, MI
Navy - AS, CG, MC, SH
Air Force – 99
NOTE: The activities listed above were interested in this document as of the date of this document.
Since organizations and responsibilities can change, you should verify the currency of the information
above using the ASSIST Online database at https://assist.dla.mil/.