Model X2AS Rev D SMT Crossover Description The X2AS is a low profile crossover to intersect an RF and DC circuit trace in an easy to use surface mount package designed for frequencies up to 6 GHz. The X2AS is ideal for any application where an RF circuit must intersect with a DC circuit without resorting to a multilayer PCB. Parts have been subjected to rigorous qualification testing and units are 100% tested. They are manufactured using materials with x and y thermal expansion coefficients compatible with common substrates such as FR4, G10, RF-35, RO4003 and polyimide. Produced with 6 of 6 RoHS compliant tin immersion finish. Electrical Specifications ** Frequency Port Impedance Features: * * * * * * * * * DC - 6.0 GHz RF - DC Crossover Low Loss DC Isolation Surface Mountable Tape And Reel Convenient Package Lead Free 100 % Tested Mechanical Outline Return Loss GHz Ohms dB Min DC - 2.5 2.5 - 3.5 3.5 - 6.0 50 50 50 20 17 15 Insertion Loss Power dB Max Avg. CW Watts @ 85 C 0.05 0.10 0.15 30 15 10 Operating Temp. C -55 to +140 -55 to +140 -55 to +140 **Specification based on performance of unit properly installed on microstrip printed circuit boards with 50 nominal impedance. Specifications subject to change without notice. Dimensions are in Inches [Millimeters] X2AS Mechanical Outline Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model X2AS Rev D Insertion Loss and Power Derating Curves Typical Insertion Loss Derating Curve for X2AS 0 -0.02 -0.04 Insertion Loss (dB) -0.06 typical insertion loss (f=2.5Ghz) typical insertion loss (f=3.5Ghz) typical insertion loss (f=6Ghz) -0.08 -0.1 -0.12 -0.14 -0.16 -0.18 -0.2 -100 -50 0 50 100 150 200 Temperature of the Part (oC) Insertion Loss Derating: Power Derating: The insertion loss, at a given frequency, of a group of couplers is measured at 25C and then averaged. The measurements are performed under small signal conditions (i.e. using a Vector Network Analyzer). The process is repeated at 85C and 150C. A best-fit line for the measured data is computed and then plotted from -55C to 150C. The power handling and corresponding power derating plots are a function of the thermal resistance, mounting surface temperature (base plate temperature), maximum continuous operating temperature of the coupler, and the thermal insertion loss. The thermal insertion loss is defined in the Power Handling section of the data sheet. As the mounting interface temperature approaches the maximum continuous operating temperature, the power handling decreases to zero. If mounting temperature is greater than 85C, Xinger crossover will perform reliably as long as the input power is derated to the curve above. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. Model X2AS Rev D Typical Performance: 0.5 GHz to 6.0 GHz -10 Return Loss X2AS -0.1 -30 -40 -60 -55C 25C 85C 100 150C Insertion Loss (dB) Return Loss (dB) -20 -50 Insertion Loss X2AS 0 -0.2 -0.3 -55C 25C 85C 100 150C -0.4 -0.5 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Freq (MHz) Mounting In order for Xinger crossovers to work optimally, there must be 50 transmission lines leading to and from all of the RF ports. Also, there must be a very good ground to the corners of the crossover to insure proper electrical performance. If either of these two conditions are not satisfied, insertion loss, VSWR and isolation parameters may not meet published specifications. 500 1000 1500 2000 2500 3000 3500 4000 4500 5000 5500 6000 Freq (MHz) Mounting Footprint To ensure proper electrical and thermal performance there must be a ground plane with 100% solder connection underneath the part When a surface mount crossover is mounted to a printed circuit board, the primary concerns are; insuring the RF pads of the device are in contact with the circuit trace of the PCB and insuring the ground plane of neither the component nor the PCB is in contact with the RF signal. Since the component is not symmetrical, the crossovers are specifically oriented in the tape and reel. An example of how the PCB footprint could look is shown below. In specific designs, the 50 lines need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. Dimensions are in Inches [Millimeters] X2AS Rev A Mounting Footprint Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392