[AKD7756-HF] AKD7756-HF AK7756 Hands Free Evaluation Rev.0 GENERAL DESCRIPTION AKD7756-HF is a Hands-free evaluation kit for the AK7756 which is an audio processor with PCM interface, EEPROM interface, mono voice audio CODEC and microphone pre-amplifier. A speaker amplifier is integrated in this evaluation kit for easy evaluation of Hands-free function by connecting external microphones and speaker units. It is possible to access to the AKD7756-HF via USB interface, and adjustment of voice quality and noise attenuation level can be made with Windows GUI applications. An external Flash Memory for DSP programming is integrated into this kit enabling a stand-alone operation. In addition, an easy connection to a mobile phone is provided by integrated Blue Tooth module for evaluations. Ordering guide AKD7756-HF * AK7756 Hands Free System (HFS) Box * USB Control Adapter * Monitoring Board * AD-DC Converter for main power supply * Control Soft FUNCTION Write/Read access to PRAM, CRAM, OFREG and control registers of AK7756 In/Output Ports: MIC-IN/SPK-OUT/S-AMPOUT/TEL-IN/TEL-OUT Flash Memory (EEPROM) for parameter storage and stand-alone operation Blue-Tooth transceiver Wireless AKD7756-HFS BT-Transceiver Wired AK 2300 AK 7756 Xilinx EEPRO AK7835 Control Box Monitor Board PC <KM101400> 2010/06 -1- [AKD7756-HF] BOARD DIAGRAM Front Panel (1) (2) (3) (4) (5) (6) (7) (8) (9) Rear Panel (10) (11) (12) (13) Main Board (14) (15) <KM101400> (16) 2010/06 -2- [AKD7756-HF] Description No. (1) Name CONTROL PORT (2) (3) MONITOR Reset (push switch) (4) STATUS (LED) (5) FRONT DIP SW (6) DSP MODE (LED + Toggle Switch) JX0/JX1 (push switch) HOOK (push switch) (7) (8) (9) (10) BT - RST (push switch) +12V (power supply) (11) (12) GND Analog interface (13) (14) VCC-OUT SPK_PDN (15) PCB DIP SW1 (16) D_BT_IF port (JP1: 5pin header) Function This port is used when the control code is written to the AK7756 via PC, or when flash memory data is downloaded. Connector for monitoring board. Without Control box AK7756 IRSTN pin control (PUSH: RESET). With Control box: Disabled When controlling the AKD7756-HF by a PC, this reset switch is not valid and a reset should be made by control soft. RED: It shows a status of the AK7756's STO pin. (Light: "H", Off: "L") BLUE: It shows a Bluetooth status. (Blinking: pairing wait, Off: paring complete) 1:I2CSEL Control BUS select of the AK7756 H:I2C, L: 4WIRE 2:BT/CODEC Far-end connection select H: Wireless (Blue Tooth) L: Wired (AK2300) 3:STO/SDLED AK7756 Pin No. 10 output select (STO/RDY/SDOUT1 pin) H: MONITER LED L: FRONT PANEL LED 4:MODE1 AK7756 Pin No. 6 control when I2CSEL (EXTEEP pin) H: No. 6pin of AK7756 is "H" L: No. 6pin of AK7756 is "L" 5:MODE2 AK7756 Pin No. 17 control (JX1 pin) H: Controlled by DSP MODE L: Controlled by FRONT DIP SW Human Interface Function (JX1) 0: L 1: H Human Interface Function (JX) Push: H Release: L Bluetooth Unconnected: The AKD7756 becomes stand-by sate when pushing this switch for seven seconds. Bluetooth connected: Off Hook / On Hook can be controlled by this switch. Reset Control of internal Bluetooth module Push: Reset Release: Reset release; 12VDC Power Supply. Supply 12V by attached power cable. Ground RCA ports for analog Inputs/Outputs MIC-IN: AIN input of the AK7756 (Single-End, Microphone Input) FES-OUT: VR output of the AK2300 (Wire Phone Voice Output) FES-IN: VFTN input of the AK2300 (Wire Phone Voice Input) SPK-OUT: AOUT output of the AK7756 (Line Output) S-AMPOUT: VCP/N output of the AK7835 (Speaker Output) For external MICBIAS. Outputs 5V Control of the AK7835 Short: Power Down Open: Power Up 1:DIF1 Data Interface Select of the AK2300 L: PCM_Short, I2S H: PCM_Long, Left justified 2,3:DIF0[1:0] Data interface switch of the AK2300 [DIF0_1,DIF0_0]=[L,L]A-law =[L,H] -law =[H,x]Linear PCM (x: don't care) 4:MODE3 Reserved (Low: default) 5:MODE4 Reserved (Low: default) When using other Bluetooth Transceiver or PCM Codec, connect them to this interface. The integrated Bluetooth module should be disconnected. <KM101400> 2010/06 -3- [AKD7756-HF] I/O ports of the AK7756 are used when an external Bluetooth module is in master mode. Pin# Name Function 1 BT-SDI AK7756-SDOUT1 Output 2 BT-SDO AK7756-SDIN1 Input 3 BT-LRCK AK7756 LRCK Input 4 BT-BICK AK7756 BICK Input 5 GND Ground Table 1. Main Board Functions (Bold: Default Setting) USB Control Adapter (USB to 10 pin flat) Box Flat USB TheAKD7756-HF should be connected to a PC via an USB control box. The USB control box is connected to a PC with an USB cable and theAKD7756-HF with 10-pin flat cable. TheAKD7756-HF can be controlled by a PC with this USB control adapter. <KM101400> 2010/06 -4- [AKD7756-HF] Evaluation Mode (Bluetooth mode) Front panel, DIP-SW2: Set to "H". 1. Bluetooth Mode (with Built-in Bluetooth module) (1) Rear Connector: MIC-IN and a microphone, SAMPOUT and speakers are connected. Bluetooth-Transceiver Microphone Mobile Phone Bluetooth connection AIN AK7756 Speaker AK7835 VCP/N Figure 1. Bluetooth Mode Data Flow (2) Evaluation Flow <Bluetooth Pairing> * Power on the AKD7756-HF. * Push and hold the HOOK button on front panel of the AKD7756-HF for more than seven seconds. When releasing the button, LED of the status2 is ON and the AKD7756-HF becomes Bluetooth pairing wait state. * Set a mobile phone into Bluetooth search state. * Search result is displayed. * Select [Free2move WA] from the search result and register it. * Enter [0000] when password is required. * Bluetooth registration complete message will be displayed. * Select the registered machine and connect them when power-on the AKD7754-HF next time. The peripheral search flow will not be the same way, depending on a mobile phone. (ex. A password for mobile phone may be required) Please refer to the usage manual of the mobile phone for details. <Call & Disconnect> Receive: When hear the ring tone, push the HOOK button on front panel of the AKD7756-HF Transmit: Push the HOOK button on front panel of the AKD7756-HF after making a call by mobile phone. Disconnect: Push the HOOK button on front panel of the AKD7756-HF. <Note> The built-in Bluetooth module can register three mobile phones at a maximum. The fourth mobile phone can not be registered when it already has three registered mobile phones. In this case, all registered mobiles should be unregistered once to register the fourth mobile. The built-in Bluetooth module can be initialized by pressing the HOOK button and BE-RST button in front panel of the AKD7756-HF for more than five seconds to cancel registered mobiles. <KM101400> 2010/06 -5- [AKD7756-HF] CONTROL SOFTWARE MANUAL Evaluation Board and Control Software Set-up 1) Connect the AKD7756-HF to the USB control box. 2) Connect the AC-DC adaptor to the +12V port of the AKD7756-HF. 3) Connect the USB control box to a PC with USB cable. The USB control box is recognized as HID (Human Interface Device) on the PC. When it can not be recognized correctly (e.g., recognized as an unknown device), please push the reset button (yellow) of the USB control box. 4) Insert the attached CD-ROM into the CD-ROM driver of the PC. Access the CD-ROM and execute "AK7756HF.exe". 5) When using Bluetooth, connect a mobile phone to Bluetooth Module. Refer to the evaluation flow of above-mentioned in Bluetooth mode. Figure 2. Startup Screen of the Control Software Note: The software must run again when disconnecting a USB control box from the PC. <KM101400> 2010/06 -6- [AKD7756-HF] Control Software Functions 1. Code Downloading There are three code areas in the AK7756 as below. Code Area Alias Function Control Register CONT AK7756 operation mode setup Program RAM PRAM RAM for HF program code Coefficient RAM CRAM Setting parameters used on the HF program Table 2. AK7756 Code Area (Note 1) Setting programs can be provided by AKM on request. The setting can be made by SCRIPT writing mode of the GUI. Write CONT Example: File Name: set_RegScript.txt (2) (1) After writing a setting program, press CODEC and DSP buttons to power-up. The AK7756 starts operation. (DSP= "H", CODEC= "H") Figure 3. Control S/W [Script] tab screen Write PRAM and CRAM (1) Example: PRAM File: AK7756HF_T1.obj CRAM File: AK7756HF_T1.cra (2) (3) (4) Figure 4. Control S/W [Download] tab screen <KM101400> 2010/06 -7- [AKD7756-HF] Parametric Equalizers The parametric equalizers as follows are included in HF code. Name Receiving-PEQ Sending-PEQ MIC-Comp-PEQ MIC_IN_PEQ SPK_OUT_PEQ Function Filter for receiving sound 4-band IIR CRAM Address 1st Band:(1C4h) ~ (1C8h) 2nd Band:(1C9h) ~ (1CDh) 3rd Band:(1CEh) ~ (1D2h) 4th Band:(1D3h) ~ (1D7h) Filter for transmitting sound 1st Band:(1D8h) ~ (1DCh) 8-band (4+4) IIR 2nd Band:(1DDh) ~ (1E1h) 3rd Band:(1E2h) ~ (1E6h) 4th Band:(1E7h) ~ (1EBh) 5th Band:C(478h) ~ C(47Ch) 6th Band:C(47Dh) ~ C(481h) 7th Band:C(482h) ~ C(486h) 8th Band:C(487h) ~ C(48Bh) Spatial distortion correction filter Fix Band:C(399h) ~ C(39Dh) 2-band IIR fixed Fix Band:C(39Eh) ~ C(3A2h) 4-band IIR variable 1st Band:C(1ECh) ~ C(1F0h) 2nd Band:C(1F1h) ~ C(1F5h) 3rd Band:C(1F6h) ~ C(1FAh) 4th Band:C(1FBh) ~ C(1FFh) MIC Filter Fix Band:C(3A4h) ~ C(3A8h) 2-band IIR fixed Fix Band:C(3A9h) ~ C(3ADh) 4-band IIR variable 1st Band:C(214h) ~ C(218h) 2nd Band:C(219h) ~ C(21Dh) 3rd Band:C(21Eh) ~ C(222h) 4th Band:C(223h) ~ C(227h) Speaker Output Filter 1st Band:C(3B1h) ~ C(3B5h) 8-band (4+4) IIR 2nd Band:C(3B6h) ~ C(3BAh) 3rd Band:C(3BBh) ~ C(3BFh) 4th Band:C(3C0h) ~ C(3C4h) 5th Band:C(200h) ~ C(204h) 6th Band:C(205h) ~ C(209h) 7th Band:C(20Ah) ~ C(20Eh) 8th Band:C(20Fh) ~ C(213h) Table 3. HF PEQ tables 5 types of filters can be selected on GUI software. Type Name Boost and decompress for specific frequency DIP LPF12 Low Pass Filter 12dB/oct HPF12 High Pass Filter 12dB/oct LPF6 Low Pass Filter 6dB/oct HPF6 High Pass Filter 6dB/oct Table 4. Filter attribute table <KM101400> 2010/06 -8- [AKD7756-HF] 8 bands adjustments can be made in RUN state by GUI. (1) (2) (3) Figure 5. Control S/W [PEQ] tab screen (1) Select [PEQ] tab to open Equalizer dialogue. (2) Push down the [USE] button to write this operation setting to the DSP. Set the initial address of the PEQ band, which need to be modified, to [ADDR]. Set quality factor of the filter to [Q]. Set a cutoff frequency of the filter to [FREQ]. Use the [Type] pull-down menu box to select a filter type. When filter type is "DIP", the slid bar is available for setting. (3) This function is enabled only when CODEC and DSP buttons are pushed down (CODEC and DSP are in RUN state). <KM101400> 2010/06 -9- [AKD7756-HF] Noise Canceller The noise canceller sets optional noise attenuation for 6 divided voice bands. This noise cancel adjustment is made with the real time NC parameter adjustment function of GUI software as shown in the following diagram. Sensitivity Adjustment When it is high, sensitivity decreases, and stability improves. When it is low, sensitivity improves, and stability decreases. The noise attenuation of each band is adjusted. Unit = [dB] GAIN0= Lowest frequency band GAIN5= Highest frequency band Figure 6. Control S/W [NC Tune] tab screen Parameter Adjustment Set the parameters in CRAM to adjust Hands Free setting. In this instruction manual, CRAM addresses are expressed as C (xx). Address = 4Ch is shown below as an example. Example: C(4Ch) CRAM Address 4Ch A corresponding example to the CRAM file is shown below. Figure 7. AK7756 CRAM File Format Figure 7 shows that 0710h is stored to C(0004Ch) when this file is downloaded. <KM101400> 2010/06 - 10 - [AKD7756-HF] With GUI, it is possible to make adjustment of 8 CRAM parameters simultaneously in RUN state. (1) (2) (3) Figure 8. Control S/W [Mon/Slider] tab screen (1) Select [Mon/Slider] tab. (2) Push down the [USE] button to write this operation setting to the DSP. First, write the address to [ADDR]. Without using the slid bar, it is also possible to input the value to [VAL]. Set the range of the slide bar to [MAX] and [MIN]. (Usually 7FFF ~ 0000) (3) This function is enabled only when CODEC and DSP buttons are pushed down. (CODEC and DSP are in RUN state) <KM101400> 2010/06 - 11 - [AKD7756-HF] REVISION HISTORY Date (yy/mm/dd) 10/06/30 Manual Revision KM101400 Board Revision 0 Reason Page Contents First Edition IMPORTANT NOTICE z These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. z Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. z Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. <KM101400> 2010/06 - 12 - 5 4 3 2 SPK-AMP 7835INN AOUT AIN EX-IN EX-OUT ANALOG D 1 D SPK-AMP ANALOG AK7756 SCL SDA/SO SI EXTEEP/CSN I2CSEL JX1 JX0 C IRSTN SDO-SPDIF STO/SDO-LED BICK LRCK SDOUT1 SDIN1 AOUT INP-AIN AK7756 C EEPROM CODEC EEP-SCL B DSP-SO SDA-CTRL DSP-SI I2CSEL SCL/SCLK-CTRL CODEC-BICK CODEC-LRCK CODEC-SDTO CODEC-SDTI DSP-EXTEEP/CSN 2300-BICK 2300-LRCK 2300-SDO 2300-SDI POWER DSP-JX1 DSP-JX0 CODEC-DIF1 CODEC-DIF0 MON-SDO-SPDIF DSP-STO-SDOUTM 2300-DIF1 2300-DIF0 DSP-BICK DSP-LRCK DSP-SDO1 DSP-SDI1 XCONTROL EEP-WE 2300-EX-IN 2300-EX-OUT EEP-SDA EEPROM B CODEC ECNS-CTRL BT-CONECT BT-BICK BT-LRCK BT-SDO BT-SDI BT-RESET BT-HOOK BT-LED POWER BlueT-BICK BlueT-LRCK BlueT-SDO BlueT-SDI FRONT-BT-RST FRONT-HOOK FRONT-BT-LED DSP-RESET BT-CONECT A A XCONTROL Title Size A4 Date: 5 4 3 2 Document Number AKD7756-HF TOP Thursday, November 19, 2009 Sheet Rev 1.0 1 1 of 9 5 4 3 2 1 D D C1 22p DVDD VDD+1.8V CRY-XTI U1 X1 C2 10u/10V(TA) + 1 DVDD18 2 VSS1 3 DVDD C3 0.1uF SDOUT1 R1 51 30 XTO 29 I2CSEL 28 12.288MHz C4 22p AK7756_30pin_VSOP + C5 10u/10V(TA) C XTI C6 0.1uF I2CSEL C7 0F(OPEN) 4 SDOUT1 LFLT 27 C9 1u/6.3V(A) JX0 INN R2 8.2k T1 26 1 + 5 JX0 C C8 33n C10 1u/6.3V(A) EXTEEP/CSN INP/AIN 25 INP-AIN + 6 EXTEEP/CSN T2 7 EEST/SI MICBIAS 24 8 SCL/SCLK AVDD 23 R4 51 9 SDA/SO AVDD 22 R5 51 10 VSS2 21 R6 51 11 SDOUT2/RDY VCOM 20 12 NC MPRF 19 R7 51 13 LRCK AOUT 18 R8 51 14 BICK JX1 17 SI SDA/SO STO/SDO-LED LRCK BICK SDIN1 AVDD C11 0.1uF STO/RDY/SDOUT1 B SDO-SPDIF 1 C13 0.1uF R9 51 15 R11 100k R12 100k SDIN1 IRSTN 16 + C12 10u/10V(TA) + SCL R3 51 B C15 1u/10V C14 2.2u/10V(TA) AOUT JX1 R10 51 IRSTN AK7756-30pin-VSOP A A Title Size A3 Date: 5 4 3 2 Document Number AKD7756-HF AK7756 Friday, October 30, 2009 Sheet 1 2 Rev 1.0 of 9 5 4 3 2 1 D D FES-IN HERE: Shortest wiring FES-OUT C16 RCA1 R13 10k R14 10k(DIP) 10k(DIP) removable C17 + T B S C18 R15 1uF(T) MR-552LS(R) VCC+8V RCA2 220 T B S EX-OUT 47pF + 1uF(T) R16 20k MR-552LS(W) 4 U2A + + C20 10uF(T) C19 C22 100pF C21 0.1uF 0.1uF MIC-IN EX-IN VCC+12V 8 5.1k AMP-BIAS1 C 3 NJM2119 1 R18 R19 10k 2 - R17 10k + C23 10uF(T) C SPK-OUT HERE: Shortest wiring B B R20 10k R21 10k(DIP) C25 10k(DIP) removable AOUT + T B S 1uF(T) C26 R22 1uF(T) 47pF R23 20k MR-552LS(W) RCA4 220 + C24 RCA3 T B S MR-552LS(R) 4 U2B NJM2119 - 6 7 5.1k 8 5 R24 AIN + AMP-BIAS1 memo:Ux-A C27 100pF A A Title Size A3 Date: 5 4 3 2 Document Number AKD7756-HF ANALOG Thursday, November 19, 2009 Sheet 1 3 Rev 1.0 of 9 5 4 3 2 1 D D BT-LRCK BT-BICK BT-SDO BT-SDI BLUE TOOTH VDD+3V JP1 1 2 3 4 5 C BT-SDI BT-SDO BT-LRCK BT-BICK C J1 P-HEADER BT-BICK BT-SDO BT-LRCK BT-SDI BT-LED B BT-HOOK 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 BT-RESET BT-RESET B BT-LED HEADER 20x2/M BT-HOOK A A Title Size A Date: 5 4 3 Document Number AKD7756-HF BT-CONECT Thursday, November 19, 2009 2 Sheet 4 of 1 Rev 1.0 9 5 4 3 2 1 R25 10k D D 2300-EX-OUT 10k CL1 Cut Land open 5 6 7 8 2 + 2300-EX-IN R27 2 C28 1 GST 1 R26 10k DIF1 GST VFTN VREF DR BCLK FS DIF0 U4 AK2300 16 15 14 13 2300-SDI 2300-BICK 2300-LRCK 2300-DIF0 PLLC VSS DX LVDD 1uF(T) VR VDD PDN MUTEN 4 3 2 1 2300-DIF1 C 9 10 11 12 C 2300-SDO 1 2 C29 0.056uF(+-30%) 1 C30 2 0.1uF AVDD B B AVDD 1 C31 1 C32 1 2 1uF 2 0.1uF 2 C33 1 1uF 2 C34 0.1uF A A Title Size A Date: 5 4 3 Document Number AKD7756-HF CODEC Friday, October 30, 2009 2 Sheet Rev 1.0 5 of 1 9 5 4 3 2 1 D D DVDD U5 C 1 E0 VCC 8 2 E1 WC 7 3 E2 SCL 6 EEP-SCL 4 VSS SDA 5 EEP-SDA C35 0.1uF R28 0 C EEP-WE M24256-Bx B B A A Title Size A Date: 5 4 3 Document Number Friday, October 30, 2009 2 AKD7756-HF EEPROM Sheet 6 of 1 Rev 1.0 9 5 4 3 2 1 VDD+3V LM1117-3.3V REG1 C40 + C36 OUT L2 1 C37 + C41 C42 + GND IN REG2 10uH(500mA) 2 3 1 GND L1 IN OUT C38 10uH(500mA) 2 3 7808-8V VCC+12V C39 + C43 C44 10uF(T) 0.1uF C45 + D D 10uF/16V(A) 0.1uF 0.1uF 10uF(T) 10uF/16V(A) L3 0.1uF 0.1uF AVDD DVDD L5 LM1084IS-3.3V VCC+8V L4 10uH(500mA) REG3 + IN OUT 2 3 C46 10uF/16V(A) GND 10uH(500mA) 1 L6 10uF(T) 10uH(500mA) C47 C48 0.1uF + 0.1uF C49 10uF(T) 10uH(500mA) C C L71000uH 220uF/16V(A) VDD+1.8V from power conector C51 + + C52 LM1117-1.8V L8 L9 C50 1 2 1 IN C53 10uF/16V(A) + 3 1000uF/16V(A) JP2 REG4 10uH(500mA) GND 10nF HEADER 2 C54 0.1uF OUT 10uH(500mA) 2 C55 0.1uF + C56 C57 10uF(T) 0.1uF C58 + 10uF(T) B B 1 TP1 TP(BLACK) 7808-8V C59 A 10uF/16V(A) + C60 OUT 2 1 IN GND JP3 1 L11 TP2 TP(BLACK) REG5 10uH(500mA) 1 2 HEADER 2 3 L10 C61 0.1uF 0.1uF + C62 10uF(T) MIC POWER A 10uH(500mA) Title Size A3 Date: 5 4 3 2 AKD7756-HF POWERSheet Thursday, November 19, 2009 Document Number 1 Rev 1.0 7 of 9 5 4 3 2 1 D D VCC+12V VDD+5V C65 + IN C63 INN 10uF/16V(A) GND 10uH(500mA) 1 7835INN REG6 OUT 2 C64 3 L12 LM1084IS-5.0 0.1uF + 0.1uF C66 10uF(T) SPK-GND C67 C68 + 10uF(T) 0.1uF R29 C 0.1uF 1 C69 S-AMPOUT U6 VDD+5V C VDD1 NC 10 RCA5 T B S 0 + 2 INN VCP 09 3 VDD2 VSS1 08 0.1uF 4 VSS2 VCN 07 PDN 06 MR-552LS(W) + C71 10uF(T) C70 R30 10k JP4 5 INP B AK7835 B 7835PDN SPK-GND A A Title Size A4 Date: 5 4 3 2 Document Number AK7756-HF SPK-AMP Friday, April 02, 2010 Rev 1.0 Sheet 8 1 of 9 5 4 3 2 1 D D U7 CODEC-SDTO CODEC-DIF0 CODEC-LRCK CODEC-BICK CODEC-SDTI CODEC-DIF1 BlueT-SDO BlueT-SDI BlueT-LRCK BlueT-BICK DSP-EXTEEP/CSN DSP-SI DSP-SO DSP-STO-SDOUTM DSP-RESET DSP-SDI1 DSP-SDO1 DSP-EXTEEP/CSN DSP-SI DSP-SO DSP-STO-SDOLED DSP/MON-RESET DSP-SDI1 DSP-SDO1 51 R38 51 51 51 R39 R40 R41 51 51 51 51 R42 R43 R44 R45 51 51 R47 R48 51 51 C 51 51 DSP-BICK DSP-LRCK DSP-BICK DSP-LRCK T3 1 R49 R50 OPTION4 OPTION5 OPTION6 R53 R59 OPTION3 OPTION2 OPTION1 OPTION8 T4 VDD+3V 2 4 6 8 1 3 5 7 15 16 17 5 2 64 I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8 I/O9 I/O10 I/O11 I/O12 I/O13 I/O14 I/O15 I/O16 I/O17 I/O18 I/O19 GCK1 GCK2 GCK3 GTS1 GTS2 GSR 10k 10k 10k 10k R31 R32 R33 R34 R35 VDD+3V C72 0.01uF VDD+3V SW DIP-5 I/O45 I/O44 I/O43 I/O42 I/O41 I/O40 I/O39 I/O38 I/O37 I/O36 I/O35 I/O34 I/O33 I/O32 I/O31 I/O30 I/O29 I/O28 I/O27 I/O26 I/O25 I/O24 I/O23 I/O22 I/O21 I/O20 63 62 61 60 59 58 57 56 52 51 50 49 48 47 46 45 44 43 42 40 39 38 36 35 34 33 DIP-DIF1 DIP-DIF0-1 DIP-DIF0-0 DIP-MODE3 DIP-MODE4 OPTION7 FRONT-HF-SW-X FRONT-HF-LED FRONT-STO MON-LRCKO MON-BICKO MON-SDO-SPDIF MON-SDOLED DSP-JX0 DSP-JX1 DIP-I2CSEL DIP-BT/CODEC DIP-STO/SDLED DIP-MODE1 DIP-MODE2 FRONT-RESET-X RESET-CTRL-X SO-CTRL SI-CTRL RQN-7756-CTRL-X HOST-CTRL_X TCK TDI TMS TDO 30 28 29 53 TCK TDI TMS TDO VCCINT VCCINT VCCIO VCCIO 3 37 26 55 GND GND GND GND 14 21 41 54 1 J2 OPTION4 OPTION5 OPTION6 1 4 6 7 8 9 10 11 12 13 18 19 20 22 23 24 25 27 31 32 10k DIF1 DIF0-1 DIF0-0 MODE3 MODE4 RESET-CTRL-X 51 R51 RESET-CTRL HOST-CTRL_X 51 R52 HOST-CTRL MON-SDO-SPDIF SDA-CTRL DSP-JX0 DSP-JX1 51 R54 51 51 R60 R61 51 51 51 51 R55 R56 R57 R58 SDA-CTRL DSP/MON-RESET FRONT-JX0 FRONT-JX1 DIP-I2CSEL I2CSEL VDD+3V VDD+3V B + C82 C79 0.1uF C80 0.1uF TCK TDI TDO TMS WDON RESETN WDI PFON MRN VCC GND PFI MAX706T 1 2 3 4 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 FRONT-BT-LED SCL/SCLK-CTRL ECNS-CTRL VDD+3V VDD+3V B FRONT-PANEL 2 VDD+3V JP6 8 7 6 5 C74 C75 C76 0.01uF 0.01uF 0.01uF 1 U8 HEADER 4x2/SM 2 4 6 8 10 10k JP5 MON-LRCKO MON-BICKO MON-SDO-SPDIF VDD+3V 1 3 5 7 9 R37 10k C XC9572XL-VQ64 VDD+3V R36 SW1 R46 OPTION7 OPTION 27 VDD 31 58 32 5 GND 17 0.01uF FRONT-BT-RST FRONT-HOOK FRONT-BT-RST FRONT-HOOK 51 C73 FRONT_PANEL C77 C78 0.1uF 0.01uF C81 JTAG 10uF(T) 0.1uF VDD+3V + C85 C83 0.1uF C84 0.1uF 10uF(T) A A Title Size A3 Date: 5 4 3 2 AKD7756-HF XCONTROL Thursday, November 19, 2009 Sheet 9 Document Number 1 Rev 1.0 of 9