3 Scotch-WeldTM Hot Melt Applicator LT Applicateur thermofusible 3MTM Scotch-WeldTM LT Aplicador por fusion al calor de Scotch-WeldTM LT de 3MTM OWNER'S MANUAL MANUEL DE L'UTILISATEUR MANUAL DEL PROPIETARIO Sc Ho ot c el t h- Ap We pl ld ic TM at or LT 3 tM For use with Low Melt Adhesives Utilisez avec les adhesifs a faible point de fusion Para uso con adhesivos de baja fusion Read instructions thoroughly before operating or performing any maintenance on 3MTM Scotch-WeldTM Hot Melt Applicator LT. For use with low melt adhesive only. Lisez attentivement les instructions avant d'utiliser ou d'effectuer toute tache de maintenance sur l'applicateur d'adhesif thermo-fusible LT 3MTM Scotch-WeldTM. Utilisez avec les adhesifs a faible point de fusion. Lea detalladamente las instrucciones antes de empezar a operar o de realizar cualquier mantenimiento del Aplicador por fusion al calor de Scotch-WeldTM LT de 3M. Para uso con adhesivos de baja fusion. Kit 9234 62-9234-9930-5 Kit 9237 62-9237-9930-8 Kit 9262 62-9262-9930-6 Kit 9238 62-9238-9930-6 Kit 9284 62-9284-9930-0 3 ENGLISH General Information Preventive Maintenance Thumb pressure on the feeder pushes the adhesive stick into the heat block. The adhesive is melted by the heat block and pushed out through the tip. A fixed thermostat on the heat block maintains heat block temperature. WARNING: TIP AND VALVE ARE HOT. WEAR HEATRESISTANT GLOVES WHEN CLEANING TIP. KEEP TIP POINTED AWAY FROM BODY PARTS. Start-Up and Operation WARNING: USE ONLY 3MTM SCOTCH-WELDTM HOT MELT 2'' x 5/8'' LOW MELT ADHESIVE STICKS. OTHER ADHESIVES MAY CAUSE BACKMELT AND POSSIBLE INJURY. DO NOT USE NEAR HIGHLY FLAMMABLE MATERIALS. To maintain proper operation, follow these steps. 1. Inspect nozzle tip daily. Make sure it is clean and clear of foreign matter. 2. Keep the adhesive clean and free of airborne contaminants. Accessory Tips 1. Plug the 3MTM Scotch-WeldTM Hot Melt Applicator LT into a 120 VAC grounded receptacle. Allow 5 to 10 minutes for heat-up. The 3M Scotch-Weld Hot Melt Applicator LT comes equipped with a standard .093'' tip. Contact your 3M Scotch-Weld Hot Melt Applicator distributor for additional tips. 2. Pull the feeder back toward the rear of the applicator. Applicator must be at operating temperature. Hold the valve firmly with a 5/8'' wrench and remove the tip with a 1/2'' wrench. Mount the new tip and tighten. 3. Snap a 3M Scotch-Weld Hot Melt Adhesive Stick (5/8'' x 2'') into the holder. CAUTION: Do not force adhesive. Excessive force can damage the applicator and cause molten adhesive to flow out the rear. 4. Gently press the feeder forward and push the adhesive into the heat block. Melted adhesive will flow from the tip. WARNING: TIP AND VALVE ARE HOT. KEEP TIP POINTED AWAY FROM BODY PARTS. Tip 9725 9726 9727 9785 9940 9913 9916 9921 9922 Description Mini-extension/0.072'' opening "T" tip/RSC carton closing "L" tip/FOL carton closing .070" Tapered aluminum extension .125'' opening Two-hole spreader Three-hole spreader Standard .093'' opening .063'' Fluted tip Changing Tips WARNING: THE TIP AND VALVE ARE HOT. WEAR HEATRESISTANT GLOVES AND POINT TIP AWAY FROM BODY PARTS. CAUTION: Do not overtighten. Overtightening damages threads. Repair Parts Kit CAUTION: To avoid charring or plugging of the tip, extrude at least one adhesive stick every three hours that the applicator is turned on. 9234 Valve Assembly Kit a. .093'' tip b. Valve Assembly 3M Stock # 62-9234-9930-5 Shut-Down 9237 Sleeve Kit a. Sleeve b. Brass Flange (4) 3M Stock # 62-9237-9930-8 9238 Feeder Kit a. Feeder b. Metal Clip 3M Stock # 62-9238-9930-6 9284 Power Cord Kit a. Power Cord (orange) 3M Stock # 62-9284-9930-0 9262 Heater/Thermostat Kit a. Heater Assembly b. Thermostat/TCO 3M Stock # 62-9262-9930-6 1. Unplug the applicator. 2. Extrude one adhesive stick to cool down the applicator. Troubleshooting Problem Probable Cause Correction 1. Low or no adhesive flow No heat Check to see that 120 VAC service is on. Thermal fuse in the thermostat may have blown. Use Repair Kit #9262. Shutdown procedure was not observed Allow the applicator to heat up for at least 30 minutes. Plugged tip If the applicator was left on overnight, the tip may be plugged. This may block adhesive flow and cause backmelt. CAUTION: Do not force adhesive. Clear the tip with a small nail or paper clip. Extrude the remaining adhesive stick and one new adhesive stick to clear the opening. Backmelt Remove the clip and feeder from the track of the applicator. Push the existing adhesive stick into the white sleeve approximately 3/4'' with a new adhesive stick. Remove the new adhesive stick before it melts and look into the white sleeve. Look for a thin skin of adhesive around the inside of the white sleeve. Scrape this skin toward the heat block. CAUTION: Do not damage the white sleeve. Extrude one adhesive stick to clear the sleeve. TO AVOID BACKMELT: Observe the Start-Up and Shut-Down procedures. Do not force adhesive through the applicator. 2. Dripping* Nozzle Backmelt Refer to preceding paragraph on backmelt. Worn Valve Assembly Replace valve with Repair Kit #9234 Contaminated adhesive Keep adhesive clean and free of contamination. *Thermal expansion may cause some dripping during start-up. This is normal. FRANCAIS Information generale Entretien preventif Une pression du pouce sur le distributeur pousse le baton d'adhesif dans le tampon isolant. L'adhesif fond avec le tampon isolant et il est pousse dans l'embout. Un thermostat fixe sur le tampon isolant maintient la temperature du tampon isolant constante. AVERTISSEMENT: L'EMBOUT ET LA VALVE SONT CHAUDS. PORTEZ DES GANTS THERMORESISTANT POUR NETTOYER L'EXTREMITE. NE DIRIGEZ PAS L'EXTREMITE VERS LE CORPS. Demarrage et fonctionnement AVERTISSEMENT: N'UTILISEZ QUE DES BATONS D'ADHESIF A FAIBLE POINT DE FUSION 3MTM SCOTCHWELDTM 2 po x 5/8 po. LES AUTRES COLLES PEUVENT CAUSER UN BRULAGE ET D'EVENTUELLES BLESSURES. N'UTILISEZ PAS A PROXIMITE DE MATERIAUX INFLAMMABLES. 1. Branchez l'applicateur 3MTM Scotch-WeldTM Hot Melt dans une fiche avec mise a terre de 120 volts CA. Laissez rechauffer 5 a 10 minutes. 2. Retirez le distributeur vers l'arriere de l'applicateur. 3. Glissez un petit baton de colle 3M Scotch-Weld Hot Melt (5/8 po x 2 po) dans le support. PRUDENCE: Ne forcez pas le baton de colle. Une force excessive peut endommager l'applicateur et entrainer l'ecoulement de la colle fondue vers l'arriere. Afin de maintenir un bon fonctionnement, suivez ces etapes. 1. Verifiez quotidiennement l'extremite de la buse. Assurezvous qu'elle est propre et exempte de matiere etrangere. 2. Gardez la colle propre et exempte de contaminants aeroportes. Conseils accessoires L'applicateur 3M Scotch-Weld Hot Melt est equipe avec un embout regulier de 0.093 po. Communiquez avec votre distributeur d'applicateur 3M Scotch-Weld Hot Melt pour des conseils supplementaires. L'applicateur doit etre a la temperature de fonctionnement. Tenez la buse fermement avec une cle 5/8 po et enlevez l'embout avec une cle de 3/4 po. Montez le nouvel embout et serrez. 9725 9726 9727 9785 9940 9913 9916 9921 9922 Description de l'embout Petit prolongement / ouverture de 0.072 po Embout en T / Carton a rabats normaux Embout en T / Carton a rabats FOL Extension conique en aluminium 0.07 po Ouverture 0.125 po Diffuseur a deux trous Diffuseur a trois trous Ouverture standard 0.093 po Embout cannele 0.063 po Remplacement des embouts 4. Enfoncez delicatement le distributeur vers l'avant et poussez la colle dans la chambre thermique. La colle fondue s'ecoulera de l'extremite. AVERTISSEMENT: L'EMBOUT ET LA VALVE SONT CHAUDS. PORTEZ DES GANTS THERMORESISTANT ET NE DIRIGEZ PAS L'EMBOUT VERS LE CORPS PARTIES. AVERTISSEMENT: L'EMBOUT ET LA VALVE SONT CHAUDS. NE PAS DIRIGER L'EXTREMITE VERS LE CORPS. PRUDENCE: Ne pas trop serrer. Un serrage excessif pourrait endommager les filets. PRUDENCE: Pour eviter de carboniser ou de boucher l'extremite, expulsez au moins un baton de colle a chaque trois heures d'utilisation de l'applicateur. Fermeture 1. Debranchez l'applicateur. 2. Expulsez un baton de colle pour refroidir l'applicateur. Trousse de reparation 9234 Trousse de jeu de soupape a.Embout 0.093 po b. Groupe soupape 3M no 62-9234-9930-5 9237 Trousse de manchon a. Manchon b. Bride en laiton (4) 3M no 62-9237-9930-8 9238 Trousse de distributeur a. Distributeur b. Agrafe metallique 3M no 62-9238-9930-6 9284 Trousse de cordon d'alimentation a. Cordon d'alimentation (orange) 3M no 62-9284-9930-0 9262 Trousse filament/thermostat a.Jeu de filament b. Thermostat/TCO 3M no 62-9262-9930-6 Depannage Probleme Cause probable Correction 1. Ecoulement de la colle Faible ou absent Pas de chaleur Verifiez s'il y a du courant 120 VAC. Le fusible thermique dans le thermostat a peut-etre saute. Utilisez la trousse de reparation no 9262. La procedure de fermeture n'a pas ete respectee Laissez l'applicateur se rechauffer pendant au moins 30 minutes. Embout bouche Si l'applicateur est reste allume pendant la nuit, l'embout peut etre bouche. Ceci pourrait bloquer l'ecoulement de la colle et causer un brulage. PRUDENCE: Ne forcez pas le baton de colle. Nettoyez l'embout avec un petit clou ou une agrafe pour papier. Expulsez le restant du baton de colle et un baton de colle neuf pour liberer l'ouverture. Brulage Enlevez l'agrafe et le distributeur du mecanisme de l'applicateur. Poussez le baton de colle qui est deja introduit dans le manchon blanc environ 3/4 po avec un baton de colle neuf. Enlevez le baton de colle neuf avant qu'il ne fonde et regardez dans le manchon blanc. Cherchez une fine couche de colle autour de l'interieur du manchon blanc. Grattez la couche vers le bloc de chauffage. PRUDENCE: N'endommagez pas le manchon blanc. Expulsez un baton de colle pour liberer le manchon. POUR EVITER LE BRULAGE: Respectez les procedures de demarrage et de fermeture. Ne forcez pas la colle dans l'applicateur. Brulage Reportez-vous au paragraphe precedent sur le brulage. Jeu de soupape usee Remplacez la soupape avec la trousse de reparation no 9234 Colle contaminee Maintenez la colle propre et exempte de toute contamination. 2. Egouttement* Buse *Lors de la mise en marche, l'expansion thermique peut causer de l'egouttement. Cet egouttement est normal. ESPANOL Informacion general Mantenimiento preventivo Una presion con el pulgar sobre el alimentador empujara la barra de adhesivo en el bloque de calentamiento. El adhesivo se funde en el bloque de calentamiento y saldra por el pico. Un termostato fijo mantiene la temperatura en el bloque de calentamiento. ADVERTENCIA: EL PICO Y LA VALVULA ESTAN CALIENTES. USE GUANTES RESISTENTES AL CALOR CUANDO LIMPIE EL PICO. MANTENGA EL PICO APUNTANDO HACIA OTRO LADO, NO HACIA SU CUERPO. Comienzo y operacion Para mantener una correcta operacion, siga estos pasos. ADVERTENCIA: USE SOLO BARRAS DE ADHESIVO DE BAJA FUSION 3MTM SCOTCH WELDTM 2'' x 5/8." EL USO DE OTROS ADHESIVOS PUEDE CAUSAR SOBREFUSION Y PROBABLES LESIONES. NO LO USE CERCA DE MATERIALES ALTAMENTE INFLAMABLE. 1. Inspecciones diariamente el pico de la boquilla. Asegurese de que este se halla limpio y no tiene materiales extranos. 1. Enchufe el aplicador por fusion al calor de Scotch-WeldTM LT de 3MTM en un receptaculo con conexion a tierra a 120 VAC (de las siglas en ingles para significar "Voltios de Corriente Alterna") Mantenga 5 a 10 minutos en calentamiento. 2. Jale el alimentador hacia atras, hacia la parte posterior del aplicador. 3. Coloque rapidamente una mini barra adhesiva (2'' x 5/8'') de fusion por calor Scotch Weld de 3M en el soporte. PRECAUCION: No fuerce el adhesivo hacia dentro. El uso de fuerza excesiva puede danar el aplicador y hacer que el adhesivo fundido salga por la parte posterior. 4. Oprima suavemente el alimentador hacia delante y empuje al adhesivo dentro del bloque de calentamiento. Saldra adhesivo fundido por el pico. ADVERTENCIA: EL PICO Y LA VALVULA ESTAN CALIENTES. MANTENGA EL PICO APUNTANDO HACIA OTRO LADO, NO HACIA SU CUERPO. PRECAUCION: Para evitar carbonizar o taponar el pico, extruda por lo menos una barra de adhesivo cada tres horas a partir del momento del encendido del aplicador. Cerrado 1. Desenchufe el aplicador. 2. Extruda una barra de adhesivo para enfriar el aplicador. 2. Mantenga al adhesivo limpio y libre de contaminantes del aire. Picos accesorios El aplicador por fusion al calor de Scotch-Weld LT de 3M viene equipado con un pico estandar de .093". Por picos adicionales tome contacto con su distribuidor de aplicadores por fusion al calor de Scotch-Weld LT de 3M. El aplicador debe estar a la temperatura de operacion. Sostenga firmemente con la llave de 5/8", mientras quita el pico de la boquilla con la llave de 3/4". Coloque el nuevo pico y ajuste. 9725 9726 9727 9785 9940 9913 9916 9921 9922 Descripcion del pico Abertura de mini-extension/0.072'' Pico "T" para cerrar envases de carton RSC Pico "L" para cerrar envases de carton FOL Alargamiento decreciente de aluminio de .070" Abertura de .125'' Esparcidor de dos orificios Esparcidor de tres orificios Abertura estandar de .093'' Pico estriado de .063" Cambio de picos ADVERTENCIA: EL PICO Y LA VALVULA ESTAN CALIENTES. USE GUANTES RESISTENTES AL CALOR Y APUNTE EL PICO HACIA OTRO LADO, NO HACIA SU CUERPO PARTES. PRECAUCION: No ajuste demasiado. Ajustar demasiado podria danar la rosca. Juegos de partes de reparacion 9234 Conjunto de juegos de valvula Articulo a. Pico de .093" b. Conjunto de la valvula 9237 Juego de manga Articulo a. Manga b. b. Brida de bronce (4) 9238 Juego de alimentador Articulo a. Alimentador b. b. Sujetador de metal 9284 Juego de cable electrico a. Cable electrico (color naranja) 9262 Juego de calentador/ termostato Articulo a. Conjunto de calentador b.Termostato/TCO 3M numero # 62-9234-9930-5 3M numero # 62-9237-9930-8 3M numero # 62-9238-9930-6 3M numero # 62-9284-9930-0 3M numero # 62-9262-9930-6 Solucion de problemas Problema Causa probable Correccion 1. Bajo o ningun flujo de adhesivo No hay calor Compruebe si esta conectada la corriente de 120 VAC. Puede haber saltado el fusible termico del termostato. Use el Juego de reparacion #9262. No se siguio el procedimiento de cierre Permita que el aplicador se caliente al menos durante 30 minutos. Pico taponado Si el aplicador se dejo encendido durante toda la noche, el pico puede estar taponado. Esto puede bloquear el flujo de adhesivo y causar sobrefusion. PRECAUCION: No fuerce el adhesivo hacia dentro. Limpie el pico con una pequena punta o clip de papeles. Extruda lo que resta de la barra de adhesivo y pase una nueva barra para limpiar el orificio. Sobrefusion Quite el sujetador y el alimentador de la guia del aplicador. Con una nueva barra empuje en la manga blanca aproximadamente 3/4" de la barra de adhesivo que ya estaba. Quite la nueva barra de adhesivo antes de que esta se funda y revise la manga blanca. Busque una fina pelicula de adhesivo alrededor del interior de la manga blanca. Raspe esta pelicula en direccion al bloque de calentamiento. PRECAUCION: No dane la manga blanca. Extruda una barra de adhesivo para limpiar la manga. PARA EVITAR LA SOBREFUSION: Siga los procedimientos de Iniciacion y Finalizacion. No fuerce el adhesivo dentro del aplicador. 2.Goteado* Boquilla Sobrefusion Consultar el parrafo anterior relativo a Sobrefusion. Conjunto para valvula gastada Reemplazar con el Juego de reparacion #9234 Adhesivo contaminado Mantenga el adhesivo limpio y libre de contaminacion. *La expansion termal puede causar algun goteo durante el comienzo. Esto es normal. Repair Service During Warranty Period - Contact your nearest 3M Sales Branch or 3MTM Scotch-Weld HotTM Melt Adhesive distributor. After Warranty Period - The 3MTM Scotch-WeldTM Hot Melt Applicator LT has been engineered to be durable and reliable. Recognizing that it will need maintenance, we have made it easy to disassemble and repair. Should your applicator require repair, you can order repair part kits from your local 3M Scotch-Weld Hot Melt Adhesive distributor. If you do not wish to make your own repair, check with your distributor. Many of our 3M Scotch-Weld Hot Melt Adhesive distributors have in-house repair capability. Warranty Repair Center 1150 Holstein Drive Pine City, MN 55063 Limited Warranty Your 3M Scotch-Weld Hot Melt Applicator LT is warranted by the 3M Company for a period of 12 months from date of use or purchase (whichever occurs first) against defects in material and workmanship. During this period repairs or replacements will be made free of charge at the option of the warrantor. This warranty does not cover damages caused by accident or misuse; or repair by an unauthorized repair station; or by the installation, operation, or maintenance not in accordance with 3M's recommended procedures; or by the use of adhesive cartridges other than 3M manufacture or which are not subject to 3M's quality control standards. All transportation, mailing, and insurance costs to the repair facility are at the expense of the owner. The foregoing warranties are exclusive and in lieu of all other warranties whether written, oral, implied or statutory. NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE SHALL APPLY. 3M's limit of liability and user's exclusive remedy shall be repair or replacement or a refund of the purchase price, at 3M's option. Limitation of Liability Except for the exclusive remedy stated above, 3M shall not otherwise be liable for any loss or damages, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including negligence, warranty, or strict liability. RoHS compliant means that the product or part does not contain any of the substances in excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/EC, unless the substance is in an application that is exempt under RoHS. Unless otherwise stated by 3M in writing, this information represents 3M's knowledge and belief based on information provided by third party suppliers to 3M. 3M Branch Offices Alaska 11151 Calaska Circle Anchorage, AK 99515-2900 Phone: 907-522-5200 Canada 1840 Oxford St. East P.O. Box 5757, Terminal A London, Ontario Canada N6A 4TI Phone: 519-451-2500 Fax: 519-452-6262 Georgia 2860 Bankers Industrial Dr. Atlanta, GA 30360-2764 Phone: 770-447-7000 Fax: 770-447-7161 Hawaii 4443 Malaii Street Honolulu, HI 96818-3136 Phone: 808-422-2721 Fax: 808-422-9557 Illinois 4 Westbrook Corporate Center Suite 300 Westchester, IL 60154 Phone: 708-338-4580 Fax: 708-338-5601 Mexico 3M Mexico S.A. de C.V. Avenida Santa Fe #55 Col. Santa Fe C.P. 01210, Mexico Phone: 52-55-52-70-04-00 Fax: 52-55-52-70-22-99 Michigan 19460 Victor Pkwy. Livonia, MI 48152-1061 P.O. Box 537907 Livonia, MI 48153-7907 Phone: 734-953-9300 Fax: 734-779-5239 Minnesota 6455 City West Pkwy Eden Prairie, MN 55344 Phone: 1-800-328-3271 Fax: 952-947-0440 6744 33rd Street North Oakdale, MN 55128-3623 Phone: 651-737-6700 New Jersey 20 Waterview Blvd., Suite 360 Parsippany, NJ 07054-1229 Phone: 973-658-3801 Fax: 973-658-3799 Pennsylvania 7 Neshaminy Interplex, Suite 400 Trevose, PA 19053 Phone: 215-638-6371 Fax: 215-638-6482 Puerto Rico 350 Chardon Avenue, Suite 1010 San Juan, PR 00918 P. O. Box 6100 Carolina, PR 00986-6100 Phone: 787-620-3000 Fax: 787-620-3012 Tennessee 763 Walnut Knoll Lane, #8 Cordova, TN 38018-6301 Phone: 901-752-4441 Fax: 901-752-4496 Texas 12700 Park Central Drive, Suite 1210 Dallas, TX 75251-1504 Phone: 214-324-1000 West Virginia Rock Branch Regional Industrial Park Poca, WV 25159 Phone: 304-755-0719 3 Industrial Adhesives and Tape Division St. Paul, MN 55144-1000 1-800-364-3577 or 651-737-6501 www.3M.com/adhesives Recycled Paper 40% pre-consumer 10% post-consumer Printed in U.S.A. (c)3M 2006 38-9019-0536-4 Contact: Creator: Phone: Fax: Address: Spec # Structure: Inks: Date: SCALE: Jenny Young Susan Barker (651) 736-2971 (651) 733-5273 3M Building 223-6N-01 St. Paul, MN 55144-1000 38-9019-0536-4 34-7059-7987-9 Black 4/24/06 1 Inch Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: 3M: Polygun-LT