Accessories
www.vishay.com Vishay BCcomponents
Revision: 01-Dec-17 1Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Aluminum Electrolytic Capacitors - Accessories
(Vishay BCcomponents)
RESISTORS FOR TERMINAL MOUNTING
Resistors are used to balance the voltage over a series connection of screw terminal capacitors or to ensure discharge to a safe
voltage after power down. Vishay provides the CMS series of resistors, which are suited for direct mounting on the terminals of
screw terminal capacitors.
MOUNTING ACCESSORIES
CLAMPS FOR ST TYPES
To facilitate vertical mounting, a series of rigid clamps is available. These are made of zinc plated steel, chromium (III)
passivated, or stainless steel (Ø D = 76 mm).
The clamps have either two or three mounting lugs, may be easily slipped over the capacitor and then clamped with
a nut and bolt. Five types of clamps are available, one for each case diameter.
They are delivered without nuts or bolts.
To avoid damaging the insulation sleeve, do not overtighten the clamp screw.
DIMENSIONS in inches [millimeters]
DIAMETER MODEL
CORE DIMENSIONS in inch [mm] TERMINAL DESIGNATION
A
TYPICAL
B
± 0.031 [0.79]
C
± 0.062 [1.59]
M
± 0.0118 [0.3]
CM
HOLE DIAMETER
TYPICAL
CA
HOLE DIAMETER
TYPICAL
Ø 50 mm CMS16 0.562
[14.27]
0.312
[7.92]
1.250
[31.75]
0.875
[22.23]
0.196
[4.98] 0.265
Ø 65 mm CMS20 0.562
[14.27]
0.312
[7.92]
1.75
[44.45]
1.13
[28.7]
0.196
[4.98]
0.265
[6.73]
Ø 76 mm
CMS22 0.562
[14.27]
0.312
[7.92]
1.75
[44.45]
1.254
[31.85]
0.196
[4.98]
0.265
[6.73]
Ø 90 mm
45° ± 10°
3/4" TYP.
C
B
M
A
Accessories
www.vishay.com Vishay BCcomponents
Revision: 01-Dec-17 2Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS in millimeters AND AVAILABLE FORMS
Fig. 1 - Dimensional outline of clamp for case Ø D = 35 mm Fig. 2 - Dimensional outline of clamp for case Ø D = 50 mm
Fig. 3 - Dimensional outline of clamp for case Ø D = 65 mm Fig. 4 - Dimensional outline of clamp for case Ø D = 76 mm
Fig. 5 - Dimensional outline of clamp for case Ø D = 90 mm
0
- 0.5
Ø 4.5 ± 0.1
12
± 0.5
63
35
51.5 ± 0.2
12 ± 0.5
6 ± 1
1
35°
23.5 10
4.5
12.05
11.05
7
61
Ø 4.4 min
12.5 max.
4 min.
60°
60°
10.5
50
49
67.5
66.5
80 max.
12.5
11.5
7
61
Ø 4.4 min.
65
64
88.5
87.5
101 max.
12.5 max.
4.5
60°
60°
10.5
19
28.5
Ø 5 ± 0.3
1
10.5
10.5
D
15°
12.5
89
99
120°
4.5
7
11 5.5
30 ± 1
Ø 4.2 ± 0.1
24 ± 0.5
4.5
12
120°(3 x)
4.5 ± 0.5
14
7
Ø 90
Ø 101.6 ± 0.5
Ø 111.1 ± 1
1
Accessories
www.vishay.com Vishay BCcomponents
Revision: 01-Dec-17 3Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Table 1
NUTS AND WASHERS FOR STB-VERSIONS
When mounting with the bolt, which is an integral part of the case, standard metal M8 and M12 nuts and washers may be used;
the maximum permissible torque is 4 Nm for M8 nuts and 10 Nm for M12 nuts.
If insulated mounting is required, synthetic nuts and rubber washers are available; for these nuts the maximum permissible
torque is 2 Nm (M8) and 4 Nm (M12).
DIMENSIONS in millimeters AND AVAILABLE FORMS
Fig. 6 - Insulated mounting Fig. 7 - Synthetic cap nut; see Table 2 for dimensions D, H and W
Table 2
Note
(1) Dimension W is measured across flats.
Fig. 8 - Rubber washer; thickness 2 mm
MOUNTING CLAMPS FOR SCREW TERMINALS
CASE DIAMETER ORDERING CODE
35 MAL804324031E3
50 MAL804324051E3
65 MAL804324061E3
76 MAL804323321E3
90 MAL804324921E3
Rubber
washer
W
D
Ø 17 ± 0.3
6
H
1
SYNTHETIC CAP NUTS
CASE DIAMETER
(mm) THREAD D
(mm)
H
(mm)
W (1)
(mm)
MIN. THREADED DEPTH
(mm) ORDERING CODE
35 M8 25 15 17 11.5 MAL804305561E3
50 M12 30 20 19 15.5 MAL804305571E3
RUBBER WASHERS
D
(mm)
d
(mm) ORDERING CODE
34 8.4 MAL804305591E3
49 13.0 MAL804305531E3
64 13.0 MAL804305521E3
74 13.0 MAL804313001E3
88 13.0 MAL804329961E3
d ± 0.2
D
Accessories
www.vishay.com Vishay BCcomponents
Revision: 01-Dec-17 4Document Number: 28348
For technical questions, contact: aluminumcaps2@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CLAMPS FOR SL-VERSIONS, Ø D = 25 mm, 30 mm, 35 mm, and 40 mm
To facilitate vertical mounting, a series of rigid clamps made of zinc plated steel is available. These are made of zinc
plated steel, chromium (III) passivated.
The clamps have two mounting lugs, may be easily slipped over the capacitor and then clamped with a nut and bolt.
Four types of clamps are available, one for each case diameter.
They are delivered without nuts or bolts.
To avoid damaging the insulation sleeve, do not overtighten the clamp screw.
DIMENSIONS in millimeters
Fig. 9 - Dimensional outline of clamp
for case Ø D = 25 mm, 30 mm and 40 mm
Fig. 10 - Dimensional outline of clamp
for case Ø D = 35 mm
Table 3
1.0
3
e
b
a
c10
d
7Ø 4.0 ± 0.2
4.3
30°
1+ 0.2
0
13.5
10
0
- 0.5
Ø 4.5 ± 0.1
12
± 0.5
63
35
51.5 ± 0.2
12 ± 0.5
6 ± 1
1
35°
23.5 10
4.5
MOUNTING CLAMPS FOR SOLDER LUGS
CASE DIAMETER
(mm)
a
(mm)
b
(mm)
c
(mm)
d
(mm)
e
(mm) ORDERING CODE
25 41.5 ± 0.2 25 35 18.5 56 MAL804324011E3
30 46.5 ± 0.2 30 40 21 61 MAL804324021E3
35 51.5 ± 0.2 35 - 23.5 63 MAL804324031E3
40 56.5 ± 0.2 40 50 26 71 MAL804324041E3