Accessories www.vishay.com Vishay BCcomponents Aluminum Electrolytic Capacitors - Accessories (Vishay BCcomponents) RESISTORS FOR TERMINAL MOUNTING Resistors are used to balance the voltage over a series connection of screw terminal capacitors or to ensure discharge to a safe voltage after power down. Vishay provides the CMS series of resistors, which are suited for direct mounting on the terminals of screw terminal capacitors. DIMENSIONS in inches [millimeters] 45 10 M 3/4" TYP. B A C CORE DIMENSIONS in inch [mm] DIAMETER MODEL O 50 mm O 65 mm TERMINAL DESIGNATION CM CA HOLE DIAMETER HOLE DIAMETER TYPICAL TYPICAL A TYPICAL B 0.031 [0.79] C 0.062 [1.59] M 0.0118 [0.3] CMS16 0.562 [14.27] 0.312 [7.92] 1.250 [31.75] 0.875 [22.23] 0.196 [4.98] 0.265 CMS20 0.562 [14.27] 0.312 [7.92] 1.75 [44.45] 1.13 [28.7] 0.196 [4.98] 0.265 [6.73] CMS22 0.562 [14.27] 0.312 [7.92] 1.75 [44.45] 1.254 [31.85] 0.196 [4.98] 0.265 [6.73] O 76 mm O 90 mm MOUNTING ACCESSORIES CLAMPS FOR ST TYPES To facilitate vertical mounting, a series of rigid clamps is available. These are made of zinc plated steel, chromium (III) passivated, or stainless steel (O D = 76 mm). The clamps have either two or three mounting lugs, may be easily slipped over the capacitor and then clamped with a nut and bolt. Five types of clamps are available, one for each case diameter. They are delivered without nuts or bolts. To avoid damaging the insulation sleeve, do not overtighten the clamp screw. Revision: 01-Dec-17 Document Number: 28348 1 For technical questions, contact: aluminumcaps2@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Accessories www.vishay.com Vishay BCcomponents DIMENSIONS in millimeters AND AVAILABLE FORMS 12.05 7 11.05 6 12 0.5 61 1 1 60 10.5 63 51.5 0.2 35 12.5 max. 4 min. O 4.4 min 60 12 0.5 0 4.5- 0.5 35 23.5 10 50 49 67.5 66.5 80 max. O 4.5 0.1 Fig. 1 - Dimensional outline of clamp for case O D = 35 mm 12.5 11.5 28.5 19 1 60 10.5 1 O5 10. 0.3 5 7 6 Fig. 2 - Dimensional outline of clamp for case O D = 50 mm 12.5 max. 4.5 15 4.5 120 .5 10 O 4.4 min. 60 D 7 12.5 89 99 65 64 88.5 87.5 101 max. Fig. 3 - Dimensional outline of clamp for case O D = 65 mm Fig. 4 - Dimensional outline of clamp for case O D = 76 mm 11 5.5 1 30 1 120(3 x) O 4.2 0.1 12 24 0.5 14 7 4.5 4.5 0.5 O 90 O 101.6 0.5 O 111.1 1 Fig. 5 - Dimensional outline of clamp for case O D = 90 mm Revision: 01-Dec-17 Document Number: 28348 2 For technical questions, contact: aluminumcaps2@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Accessories www.vishay.com Vishay BCcomponents Table 1 MOUNTING CLAMPS FOR SCREW TERMINALS CASE DIAMETER 35 50 65 76 90 ORDERING CODE MAL804324031E3 MAL804324051E3 MAL804324061E3 MAL804323321E3 MAL804324921E3 NUTS AND WASHERS FOR STB-VERSIONS When mounting with the bolt, which is an integral part of the case, standard metal M8 and M12 nuts and washers may be used; the maximum permissible torque is 4 Nm for M8 nuts and 10 Nm for M12 nuts. If insulated mounting is required, synthetic nuts and rubber washers are available; for these nuts the maximum permissible torque is 2 Nm (M8) and 4 Nm (M12). DIMENSIONS in millimeters AND AVAILABLE FORMS D 1 O 17 0.3 Rubber washer H 6 W Fig. 6 - Insulated mounting Fig. 7 - Synthetic cap nut; see Table 2 for dimensions D, H and W Table 2 SYNTHETIC CAP NUTS CASE DIAMETER (mm) 35 50 THREAD M8 M12 D (mm) 25 30 H (mm) 15 20 W (1) (mm) 17 19 MIN. THREADED DEPTH (mm) 11.5 15.5 ORDERING CODE MAL804305561E3 MAL804305571E3 Note (1) Dimension W is measured across flats. D d 0.2 Fig. 8 - Rubber washer; thickness 2 mm RUBBER WASHERS D (mm) 34 49 64 74 88 Revision: 01-Dec-17 d (mm) 8.4 13.0 13.0 13.0 13.0 ORDERING CODE MAL804305591E3 MAL804305531E3 MAL804305521E3 MAL804313001E3 MAL804329961E3 Document Number: 28348 3 For technical questions, contact: aluminumcaps2@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Accessories www.vishay.com Vishay BCcomponents CLAMPS FOR SL-VERSIONS, O D = 25 mm, 30 mm, 35 mm, and 40 mm To facilitate vertical mounting, a series of rigid clamps made of zinc plated steel is available. These are made of zinc plated steel, chromium (III) passivated. The clamps have two mounting lugs, may be easily slipped over the capacitor and then clamped with a nut and bolt. Four types of clamps are available, one for each case diameter. They are delivered without nuts or bolts. To avoid damaging the insulation sleeve, do not overtighten the clamp screw. DIMENSIONS in millimeters 10 13.5 3 12 0.5 1.0 61 1 e a b 63 51.5 0.2 35 c10 4.3 1 7 12 0.5 + 0.2 0 30 4.5 0 - 0.5 35 O 4.0 0.2 d 23.5 10 O 4.5 0.1 Fig. 9 - Dimensional outline of clamp for case O D = 25 mm, 30 mm and 40 mm Fig. 10 - Dimensional outline of clamp for case O D = 35 mm Table 3 MOUNTING CLAMPS FOR SOLDER LUGS CASE DIAMETER (mm) a (mm) b (mm) c (mm) d (mm) 25 41.5 0.2 25 35 18.5 56 MAL804324011E3 30 46.5 0.2 30 40 21 61 MAL804324021E3 35 51.5 0.2 35 - 23.5 63 MAL804324031E3 40 56.5 0.2 40 50 26 71 MAL804324041E3 Revision: 01-Dec-17 e (mm) ORDERING CODE Document Number: 28348 4 For technical questions, contact: aluminumcaps2@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000