5KP5.0A thru 5KP188A www.vishay.com Vishay General Semiconductor TRANSZORB(R) Transient Voltage Suppressors FEATURES * P600 glass passivated chip junction * Available in uni-directional polarity only * 5000 W peak pulse power capability with a 10/1000 s waveform, repetitive rate (duty cycle): 0.01 % * Excellent clamping capability * Very fast response time P600 * Low incremental surge resistance * Solder dip 275 C max. 10 s, per JESD 22-B106 * AEC-Q101 qualified * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 TYPICAL APPLICATIONS Use in sensitive electronics protection against voltage transients induced by inductive load switching and lighting on ICs, MOSFET, signal lines of sensor units for consumer, computer, industrial, automotive, and telecommunication. PRIMARY CHARACTERISTICS VWM 5.0 V to 188 V PPPM 5000 W PD 8.0 W MECHANICAL DATA IFSM 500 A TJ max. 175 C Case: Molded epoxy body over passivated junction Molding compound meets UL 94 V-0 flammability rating Base P/N-E3 - RoHS compliant, commercial grade Base P/NHE3 - RoHS compliant, AEC-Q101 qualified Terminals: Matte tin plated leads, solderable per J-STD-002 and JESD 22-B102 E3 suffix meets JESD 201 class 1A whisker test, HE3 suffix meets JESD 201 class 2 whisker test Polarity: Color band denotes cathode end MAXIMUM RATINGS (TA = 25 C unless otherwise noted) PARAMETER Peak pulse power dissipation with a 10/1000 s waveform Peak pulse current with a 10/1000 s waveform (1) (1) Power dissipation on infinite heatsink at TL = 75 C (fig. 5) Peak forward surge current 8.3 ms single half sine-wave (fig. 5) Instantaneous forward voltage at 100 A (2) Operating junction and storage temperature range SYMBOL LIMIT UNIT PPPM 5000 W IPPM See next table A PD 8.0 W IFSM 600 A VF 3.5 V TJ, TSTG - 55 to + 175 C Notes (1) Non-repetitive current pulse, per fig. 3 and derated above T = 25 C per fig. 2 A (2) Measured 8.3 ms single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum Revision: 13-Mar-12 Document Number: 88308 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 5KP5.0A thru 5KP188A www.vishay.com Vishay General Semiconductor ELECTRICAL CHARACTERISTICS (JEDEC REGISTERED DATA) (TA = 25 C unless otherwise noted) DEVICE TYPE 5KP5.0A 5KP6.0A 5KP6.5A 5KP7.0A 5KP7.5A 5KP8.0A 5KP8.5A 5KP9.0A 5KP10A 5KP11A 5KP12A 5KP13A 5KP14A 5KP15A 5KP16A 5KP17A 5KP18A 5KP20A 5KP22A 5KP24A 5KP26A 5KP26A 5KP28A 5KP30A 5KP33A 5KP36A 5KP40A 5KP43A 5KP45A 5KP48A 5KP51A 5KP54A 5KP58A 5KP60A 5KP64A 5KP70A 5KP75A 5KP78A 5KP85A 5KP90A 5KP100A 5KP110A 5KP120A 5KP130A 5KP150A 5KP160A 5KP170A 5KP188A BREAKDOWN VOLTAGE VBR AT IT (1) (V) MIN. MAX. 6.4 6.67 7.22 7.78 8.33 8.89 9.44 10.0 11.1 12.2 13.3 14.4 15.6 16.7 17.8 18.9 20.0 22.2 24.4 26.7 28.9 28.9 31.1 33.3 36.7 40.0 44.4 47.8 50.0 53.3 56.7 60.0 64.4 66.7 71.1 77.8 83.3 86.7 94.4 100 111 122 133 144 167 178 189 209 7.00 7.37 7.98 8.60 9.21 9.83 10.4 11.1 12.3 13.5 14.7 15.9 17.2 18.5 19.7 20.9 22.1 24.5 26.9 29.5 31.9 31.9 34.4 36.8 40.6 44.2 49.1 52.8 55.3 58.9 62.7 66.3 71.2 73.7 78.6 86.0 92.1 95.8 104 111 123 135 147 159 185 197 209 231 TEST CURRENT IT (mA) STAND-OFF VOLTAGE VWM (V) MAXIMUM REVERSE LEAKAGE AT VWM ID (A) 50 50 50 50 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100 110 120 130 150 160 170 188 2000 5000 2000 1000 250 150 50 20 15 10 5.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 MAXIMUM PEAK PULSE CURRENT IPPM (2) (A) 543 485 446 417 388 368 347 325 294 275 251 233 216 205 192 181 171 154 141 129 119 119 110 103 93.8 86.1 77.5 72.0 68.8 64.6 60.7 57.4 53.4 51.7 48.5 44.2 41.3 39.7 36.5 34.2 30.9 28.2 25.9 23.9 20.6 19.3 18.2 15.2 MAXIMUM CLAMPING VOLTAGE AT IPPM VC (V) MAXIMUM TEMP. COEFFICIENT OF VBR (%/C) 9.20 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 94 97.0 103 113 121 126 137 146 162 177 193 209 243 259 275 328 0.057 0.061 0.065 0.068 0.073 0.075 0.078 0.081 0.084 0.086 0.088 0.090 0.092 0.094 0.096 0.097 0.098 0.099 0.100 0.101 0.101 0.101 0.102 0.103 0.104 0.104 0.105 0.105 0.106 0.106 0.107 0.107 0.107 0.108 0.108 0.108 0.108 0.108 0.110 0.110 0.110 0.112 0.112 0.112 0.112 0.112 0.112 0.112 Notes (1) Pulse test: t 50 ms p (2) Surge current waveform per fig. 3 and derate per fig. 2 (3) All terms and symbols are consistent with ANSI/IEEE CA62.35 Revision: 13-Mar-12 Document Number: 88308 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 5KP5.0A thru 5KP188A www.vishay.com Vishay General Semiconductor ORDERING INFORMATION (Example) PREFERRED P/N UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE 5KP5.0AHE3/54 2.776 54 800 13" diameter paper tape and reel 5KP5.0A-E3/54 (1) 2.776 54 800 13" diameter paper tape and reel Note (1) AEC-Q101 qualified RATINGS AND CHARACTERISTICS CURVES (TA = 25 C unless otherwise noted) 150 Non-Repetitive pulse waveform shown in Fig. 3 TA = 25 C 10 1.0 TJ = 25 C Pulse Width (td) is defined as the Point where the Peak Current decays to 50 % of IPPM tr = 10 s Peak Value IPPM 100 Half Value - IPP IPPM 2 50 10/1000 s Waveform as defined by R.E.A. td 0 0.1 0.1 s 1.0 s 10 s 100 s 1 ms 10 ms 0 1.0 2.0 3.0 td - Pulse Width t - Time (ms) Fig. 1 - Peak Pulse Power Rating Curve Fig. 3 - Pulse Waveform 4.0 100 000 100 CJ - Junction Capacitance (pF) Peak Pulse Power (PPP) or Current (IPP) Derating in Percentage, % IPPM - Peak Pulse Current, % IRSM PPPM - Peak Pulse Power (kW) 100 75 50 25 TJ = 25 C f = 1.0 MHz Vsig = 50 mVp-p Measured at Zero Bias 10 000 Measured at Stand-Off Voltage VWM 1000 100 0 0 25 50 75 100 125 150 175 200 1 10 100 TJ - Initial Temperature (C) VWM - Reverse Stand-Off Voltage (V) Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature Fig. 4 - Typical Junction Capacitance Revision: 13-Mar-12 200 Document Number: 88308 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 5KP5.0A thru 5KP188A www.vishay.com Vishay General Semiconductor 500 IFSM - Peak Forward Surge Current (A) PD - Power Dissipation (W) 8 60 Hz Resistive or Inductive Load 6 4 L = 0.375" (9.5 mm) Lead Lengths 2 0 8.3 ms Single Half Sine-Wave 450 400 350 300 250 200 0 25 50 75 100 125 150 175 200 1 10 100 TL - Lead Temperature (C) Number of Cycles at 60 Hz Fig. 5 - Power Derating Curve Fig. 6 - Maximum Non-Repetitive Forward Surge Current PACKAGE OUTLINE DIMENSIONS in inches (millimeters) P600 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) 0.052 (1.32) 0.048 (1.22) DIA. 1.0 (25.4) MIN. APPLICATION NOTES The 5KP series of high power transient voltage suppressors were designed to be used on the output of switching power supplies. These devices may be used to replace crowbar circuits. Both the 5 % and 10 % voltage tolerances are referenced to the power supply output voltage level. Revision: 13-Mar-12 They are able to withstand high levels of peak current while allowing a circuit breaker to trip or a fuse blow before shorting. This will enable the user to reset the breaker or replace the fuse and continue operation. For this type operation, it is recommended that a sufficient mounting surface be used for dissipating the heat generated by the Transient Voltage Suppressor during the transient or over-voltage condition. Document Number: 88308 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Revision: 12-Mar-12 1 Document Number: 91000