TS9010 series 1-5 2003/12 rev. A
TS9010
150mA CMOS Low Dropout Voltage Regulator with Enable
Low Power Consumption
Low Dr op O ut Voltage 0.4V
Enable Shutdown
General De scription
The TS9010 series is combine high accuracy with very low power consumption, providing high output current even when
the application requires very low dropout voltage. The Chip Enable (CE) includes a CMOS or TTL compatible input allows
the output to be turned off to prolong battery life. The TS9010 series is included a precision voltage reference, error
correction circuit, a current limited output driver, over temperature shutdown, and a reference bypass pin to improve its
already excellent low-noise performance.
This series are offered in 5-pin SOT-25 package.
Features
Dropout voltage typically 0.4V @Io=150mA (Vo=5V)
Output current up to 150mA (Vout=3V)
Low power consumption
Output voltage +/-2%
Internal current limit
Thermal shutdown protection
Ordering Information
Note: Where x denotes voltage option, available are
D=1.8V,
K=2.5V,
P=3.0V,
S=3.3V,
5=5.0V.
Contact factory for additional voltage options.
Part No. Operating Temp.
(Ambient) Package
TS9010xCX5 -40 ~ +85 oC SOT-25
Applications
Palmtops
Video recorders
Battery powered equipment
PC peripherals
High-efficiency linear power supplies
Digital signal camera
Block Diagram
Typical Application Circuit
Pin assignment
1. Input
2. Ground
3. Enable
4. Bypass
5. Output
TS9010 series 2-5 2003/12 rev. A
Absolute Maximum Rating (Note 1)
Input Supply Voltage Vin +12 V
Enable Input Voltage Vce 0 ~ Vin+0.3 V
Output Current Io 200 mA
Power Dissipation (Note 3) PD 380 mW
Thermal Resistance Өja 220
oC/W
Operating Junction Temperature Range Tj -40 ~ +125 oC
Storage Temperature Range TSTG -65 ~ +150 oC
Lead Soldering Temperature (260 oC) 5 S
Recommend Operating Rating
Input Supply Voltage Vin +16 V
Enable Input Voltage Vce Gnd-0.3 ~ Vin+0.3 V
Electri cal Character istics
Ta = 25 oC, Io=1mA, Cout=2.2uF, Vce2V, unless otherwise specified.
Parameter Conditions Min Typ Max Unit
Output Voltage Vin=Vo + 1V 0.98|Vo| 1.02|Vo| V
Output Voltage Temperature
Coefficient (Note 4)
-- 100 -- ppm/ oC
Line Regulation Vo+1V Vin 10V -- 10 20 mV
TS90115 Vin=Vo+1V,
1mAIL150mA TS9011S
-- 30 80
TS9011K
Load Regulation (Note 5)
Vin=Vo+1V,
1mAIL80mA TS9011D
-- 40 90
mV
Io=150mA TS90115 -- 400 --
Io=150mA TS9011S -- 400 --
Io=100mA TS9011K -- 600 --
Dropout Voltage (Note 6)
Io=100mA TS9011D -- 800 1000
mV
Quiescent Current Vin0.4V (shutdown) -- 0.01 1 uA
Io=0.1mA -- 80 125
Io=50mA -- 350 600
Io=100mA -- 600 1000
Ground Pin Current (Note 7) Vce2V
Io=150mA -- 1300 1900
uA
Output Current Limit Vout=0V -- 300 -- mA
Power Supply Rejection Ratio At f=100Hz, Io=0.1mA, -- 70 -- dB
Thermal Regulation (Note 8) -- 0.05 -- %/W
Output Noise Io=50mA, Cout=2.2uF,
470pF from bypass to Ground
-- 260 -- nVHz
TS9010 series 3-5 2003/12 rev. A
Electri cal Character istics
Enable Input
Parameter Conditions Min Typ Max Unit
Enable Input Logic-Low Voltage Regulation shutdown -- -- 0.4 V
Enable Input Logic-High Voltage Regulation enable 2.0 -- -- V
VIL0.4V -- 0.01 1 Enable Input Current
VIL2.0V 2 5 20
uA
Note 1: Exceeding the absolute maximum rating may damage the device.
Note 2: The device is not guaranteed to function outside its operating rating.
Note 3: The maximum allowable power dissipation at any Ta is Pd(max) = [ Tj(max) - Ta] * Өja. Exceeding the maximum
allowable power dissipation will result in excessive die temperature, and the regulator will go into thermal
shutdown.
Note 4: Output voltage temperature coefficient is defined as the worst case voltage change divided by the total
temperature range.
Note 5: Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for
load regulation in the load range from 1mA to 150mA(Vout>2.5V) and 1mA to 80mA(Vout<2.5V). Changes in
output voltage due to heating effects are covered by the thermal regulation specification.
Note 6: Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its
nominal value measured at 1V differential.
Note 7: Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn
from the supply is the sum of the load current plus the ground pin current.
Note 8: Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is
applied, excluding load or line regulation effects. Specifications are for a 150mA load pulse at Vin=12V for
t=10mS.
TS9010 series 4-5 2003/12 rev. A
Applicatio n Ex ampl es
Standard Circuit
Typical Application Circuit 1
Typical Application Circuit 2
TS9010 series 5-5 2003/12 rev. A
SOT-25 Mechanical Drawing
SOT-23 DIMENSION
MILLIMETERS INCHES
DIM MIN MAX MIN MAX
A 2.70 3.00 0.106 0.118
B 0.25 0.50 0.010 0.020
C 1.90(typ) 0.075(typ)
D 0.95(typ) 0.037(typ)
E 1.50 1.70 0.059 0.067
F 1.05 1.35 0.041 0.053
H 2.60 3.00 0.102 0.118
L 0.60(typ) 0.024(typ)