PSC-100A-C - MEAN WELL ENTERPRISES

SPECIFICATION

MODEL

DC VOLTAGE

RATED CURRENT

CURRENT RANGE

RATED POWER

OUTPUT VOLTAGE ADJ. RANGE

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME Note.4

HOLD UP TIME (Typ.)

VOLTAGE RANGE

FREQUENCY RANGE

EFFICIENCY (Typ.)

INPUT

ALARM

INRUSH CURRENT (Typ.)

LEAKAGE CURRENT

SAFETY STANDARDS

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVERLOAD

OVER VOLTAGE

BATTERY CUT OFF

AC OK Note.6

BATTERY LOW

AC CURRENT (Typ.)

2400ms, 30ms/230VAC 2400ms, 30ms/115VAC at full load

40ms/230VAC 14ms/115VAC at full load

90 ~ 264VAC 127 ~ 370VDC

47 ~ 63Hz

86%

CH1:28.98 ~ 37.26V

88%

20 1V±

2A/115VAC 1.2A/230VAC

COLD START 35A/115VAC 70A/230VAC

<1mA / 240VAC

105 ~ 150% rated output power

CH1:14.49 ~ 18.63V

Protection type : Hiccup mode, recovers automatically after fault condition is removed

Protection type : Shut down o/p voltage, re-power on to recover

10 0.5V±

UL62368-1, TUV EN62368-1, approvedEAC TP TC 004

Compliance to EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020

Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A, EAC TP TC 020

-20 ~ +70 (Refer to "Derating Curve")℃

20 ~ 90% RH non-condensing

-20 ~ +85 , 10 ~ 95% RH℃

10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes

417.6K hrs min. MIL-HDBK-217F (25 )℃

PCB:127*76.2*31mm (L*W*H) ; Enclosed type:130*85*37mm (L*W*H)

PCB:0.23Kg; 63pcs/15.5Kg/1.35CUFT ; Enclosed type:0.44Kg;32pcs/15Kg/0.64CUFT

File Name:PSC-100-SPEC 2019-07-03

FUNCTION

Battery low voltage : < 11V Battery low voltage : < 22V

Relay contact output, ON : AC OK ; OFF : AC Fail ; Max. rating : 30V / 1A

Relay contact output, OFF : Battery OK ; ON : Battery Low ; Max. rating : 30V / 1A

PSC-100B

27.6V

CH1

2.4A

0 ~ 3.5A

100.74W

100mVp-p

CH1: 24 ~ 29V

±1.0%

±0.5%

27.6V

CH2

1.25A

--------

13.8V

CH2

2.5A

--------

PSC-100A

13.8V

4.75A

0 ~ 7A

100.05W

100mVp-p

CH1: 12 ~ 15V

±1.0%

±0.5%

100W Single Output with Battery Charger(UPS Function)

Universal AC input / Full range

5"x3" compact size

Models with L-Bracket and cover available (PSC-100x-C, x=A,B)

Protections: Short circuit / Overload / Over voltage

Battery low protection / Battery reverse polarity protection by fuse

Relay contact signal output for AC OK and Battery Low

Cooling by free air convection

100% full load burn-in test

2 years warranty

PSC-100 series

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

PROTECTION

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC

I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃

SAFETY &

EMC

(Note 4)

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.¢

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Length of set up time is measured at first cold start. Turning ON/OFF the power supply may lead to increase of the set up time.

5. Heat sink HS2,HS3 can not be shorted.

6. Heat sink HS2,HS3 must have safety isolation distance from system case.

7. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on

a mm* mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives.230 230 For guidance on how to

perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com)

8. Please refer to suggest application (2) (4) in page 3.、

9. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

CH1

OUTPUT NUMBER

EMC IMMUNITY

EMC EMISSION

PSC-100A -C =Blank,-C ; Blank=PCB only, -C=Enclosed type=Blank,-C ; Blank=PCB only, -C=Enclosed type

±℃℃0.03%/ (0~50 ) on CH1 output

Bauar

Sicherheit

egel gema

t gepruft

www.

ID 2000000000

tuv.com

wac g

EN62368-1

UL62368 1-

IEC62368-1

TPTC004

Mechanical SpecificationMechanical Specification Unit:mm

Block Diagram

CIRCUIT

DETECTION

ALARM

RL1

RL2

O.L.P.

EMI FILTER

RECTIFIER

POWER

SWITCHING FILTER

RECTIFIERS +V

Bat. +

Battery Charger

Back up Control

AC OK

-V

Bat. -

Bat. Low

I/P

CONTROL

PWM

O.V.P.

5.6 115.8

127

3max.

CN2

CN1

FS1

CN3

4- 3.8£

5.7

64.75

76.2

31max.

SVR1

AC FUSE

T3.15A/250V

HS2 HS3

DC Output Connector (CN2) : JST B8P-VH or equivalent

Pin No.

1,2

3,4

5,6

7,8

Assignment

-V

Bat+

Bat-

Mating Housing

JST VHR

or equivalent

Terminal

JST SVH-21T-P1.1

or equivalent

AC Input Connector (CN1) : JST B3P-VH or equivalent

Pin No.

Assignment

AC/N

No Pin

AC/L

Mating Housing

JST VHR JST SVH-21T-P1.1

or equivalent or equivalent

Terminal

JST XHP JST SXH-001T-P0.6

Alarm Output Connector(CN3) : JST B4B-XH or equivalent

Pin No.

Mating Housing

or equivalent

Terminal

or equivalent

Assignment

AC OK

Bat. Low

1.HS2,HS3 cannot be shorted.

2.HS2,HS3 must have safety isolation distance from system case.

3.-V and Bat- can not be shorted.

4.M1 is safety ground. For better EMC performance,Please secure

an electrical connection between M1,M2,M3,and chassis grounding.

100W Single Output with Battery Charger(UPS Function) PSC-100 series

2-M3 L=4

130

6-M3 L=4

7.1

2-M3

115.8

41.7

68.6

8.2

L-Bracket:

No. 946A-D

Cover:

No. 946B-T

Mylar film

: Grounding Required

File Name:PSC-100-SPEC 2019-07-03

Bat+

-V

Bat-

Load

A : 12V

B : 24V

Battery

Suggested Application

CN3 Pin2(Pin4) External voltage source (V)

and resistor (R)

(The max. Sink is 1A and 30V)

1.Backup connection for AC interruption

2.Alarm signal for AC OK and Battery Low

(1) Please refer to the Fig1.1 for suggested connection.

(1) Alarm signal is sent out through " AC OK " & " Battery Low " pins.(relay contact type)

(2) An external voltage source is required for this function. The maximum applied voltage is 30V and the maximum sink current is 1A.

(3) Table2.1 explains the alarm function built in the power supply

AC OK (Battery low)

CN3 Pin1(Pin3)

Function Output of Alarm

voltage 30V max.)

Low or short

High or open(External applied

Description

The signal is "Low" when the power supply

The signal is "Low" when the voltage of

The signal is "High" when the voltage of

The signal turns to be "High" when the power

turns on

battery is under A:11V, B:22V

battery is above A:11V, B:22V

supply turns OFF

AC OK

Battery

Low

The power supply charges the battery and provides energy to the load at the same time when the AC main is OK.

The battery starts to supply power to the load when the AC mains fails.

Fig 1.1 Suggested system connection

Table 2.1 Explanation of Alarm Signal

100W Single Output with Battery Charger(UPS Function) PSC-100 series

Output Derating VS Input Voltage

INPUT VOLTAGE (VAC) 60Hz

90 10095 120115 160140 200180 240220 264

LOAD (%)

100

Output Derating

AMBIENT TEMPERATURE ( )¢

LOAD (%)

-20 0 2010 30 40

100

6050 70 (HORIZONTAL)

PCB only

Enclosed type

PCB only

(4) RL1 (AC OK)signal will go into hiccup mode when the overload protection is activating. Fig 2.2 Internal circuit of AC OK (Battery Low)

Enclosed tpye

File Name:PSC-100-SPEC 2019-07-03