User's Manual IE-78K0S-NS In-Circuit Emulator Target Devices 78K/0S Series Document No. U13549EJ2V0UM00 (2nd edition) Date Published September 2002 N CP(K) (c) 1998 Printed in Japan [MEMO] 2 User's Manual U13549EJ2V0UM V40 and V850 Series are trademarks of NEC Corporation. Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. * The information in this document is current as of July, 2002. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. * NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. * NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 User's Manual U13549EJ2V0UM 3 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 NEC do Brasil S.A. Electron Devices Division Guarulhos-SP, Brasil Tel: 11-6462-6810 Fax: 11-6462-6829 * Filiale Italiana Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 NEC Electronics Hong Kong Ltd. * Branch The Netherlands Eindhoven, The Netherlands Tel: 040-244 58 45 Fax: 040-244 45 80 NEC Electronics Hong Kong Ltd. * Branch Sweden Taeby, Sweden Tel: 08-63 80 820 NEC Electronics (Europe) GmbH Fax: 08-63 80 388 Duesseldorf, Germany * United Kingdom Branch Tel: 0211-65 03 01 Milton Keynes, UK Fax: 0211-65 03 327 Tel: 01908-691-133 Fax: 01908-670-290 * Sucursal en Espana Madrid, Spain Tel: 091-504 27 87 Fax: 091-504 28 60 Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics Shanghai, Ltd. Shanghai, P.R. China Tel: 021-6841-1138 Fax: 021-6841-1137 NEC Electronics Taiwan Ltd. Taipei, Taiwan Tel: 02-2719-2377 Fax: 02-2719-5951 NEC Electronics Singapore Pte. Ltd. Novena Square, Singapore Tel: 253-8311 Fax: 250-3583 * Succursale Francaise Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 J02.4 4 User's Manual U13549EJ2V0UM Major Revisions in This Edition Page Description Throughout * Addition of interface board IE-70000-PCI-IF-A * Deletion of interface card IE-70000-CD-IF and addition of IE-70000-CD-IF-A p.12 Figure 1-1 IE-78K0S-NS System Configuration * Supply media of debugger ID78K0S-NS changed to CD-ROM * Addition of Web site where device file can be obtained as Note 1 pp.19 to 21, 24, and 25 CHAPTER 3 INSTALLATION * Modification of Figure 3-1 Connecting Emulation Board (When using an emulation board on which P1, P2, and P3 connectors are mounted) * Modification of Figure 3-2 Connecting Emulation Board (When using an emulation board on which CN5, CN6, CN7, and CN8 connectors are mounted) * Modification of Figure 3-3 Connecting Emulation Probe * Deletion of SW1 from previous edition and addition of SW2 in Figure 3-6 Default Settings of SW2, SW3, SW4, JP1, and JP4 * Addition of CN4 and SW2 in Figure 3-7 Part Names of G-789000 Board pp.26 and 27 Addition of APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC pp.28 and 29 Deletion of previous APPENDIX C PC CARD INTERFACE (IE-70000-CD-IF) Addition of APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) pp.30 to 32 Modification of APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES) pp.33 to 35 Modification of APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES The mark shows major revised points. User's Manual U13549EJ2V0UM 5 INTRODUCTION Product overview The IE-78K0S-NS is used in combination with an emulation board (IE-789xxx-NS-EM1) to debug products in the 78K/0S Series of 8-bit single-chip microcontrollers. Readers This manual is intended for engineers who perform debugging of systems that use products in the 78K/0S Series of 8-bit single-chip microcontrollers, using the IE-78K0S-NS and an emulation board (IE-789xxx-NSEM1). Purpose The purpose of this manual is to help the reader understand the debugging functions that are available by using the IE-78K0S-NS and an emulation board (IE-789xxx-NS-EM1) together. Organization When using the IE-78K0S-NS, please refer to the manual (this manual) that comes with the IE-78K0S-NS as well as the manual that comes with the emulation board (IE-789xxx-NS-EM1). IE-78K0S-NS IE-789xxx-NS-EM1 User's Manual User's Manual (This manual) * Basic specifications * Function outline * System configuration * Target interface differences * External interface function How to read this manual To understand the overall functions of the IE-78K0S-NS Read this manual in the order of the CONTENTS. To understand the basic specifications Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES. For how to connect the IE-789xxx-NS-EM1 and make settings to debug 78K/0S Series products Refer to CHAPTER 3 INSTALLATION. 6 User's Manual U13549EJ2V0UM Terminology The meanings of the terms used in this manual are described in the table below. Terms Emulation device Meaning This is a general term for the device in the emulator that is used to emulate the target device. It includes the emulation CPU. Emulation CPU This is the CPU block in the emulator that is used to execute user-generated programs. Target device This is the device to be emulated. Target system This is the system to be debugged. It includes the target program and the hardware created by the user. When defined narrowly, it includes only the hardware. Conventions Data significance: Higher digits on the left and lower digits on the right Note: Footnote for item marked with Note in the text Caution: Information requiring particular attention Remark: Supplementary information User's Manual U13549EJ2V0UM 7 CONTENTS CHAPTER 1 GENERAL.......................................................................................................................... 11 1.1 System Configuration .............................................................................................................. 11 1.2 Hardware Configuration .......................................................................................................... 13 1.3 Basic Specifications ................................................................................................................ 14 CHAPTER 2 PART NAMES................................................................................................................... 15 2.1 Parts of Main Unit ..................................................................................................................... 15 2.2 Board Name .............................................................................................................................. 17 CHAPTER 3 INSTALLATION ................................................................................................................. 18 3.1 Connection................................................................................................................................ 18 3.2 External Trigger Functions...................................................................................................... 23 3.3 Jumper or Switch Settings (on Main Board (G-789000 Board))........................................... 24 APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC ............................... 26 A.1 Introduction .............................................................................................................................. 26 A.2 Installation ................................................................................................................................ 27 APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) ................................................................ 28 B.1 Introduction .............................................................................................................................. 28 B.2 Installation ................................................................................................................................ 29 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES) ............................................................................................ 30 C.1 Introduction .............................................................................................................................. 30 C.2 Installation ................................................................................................................................ 31 APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES...................................................................................................... 33 D.1 Introduction .............................................................................................................................. 33 D.2 Installation ................................................................................................................................ 34 8 User's Manual U13549EJ2V0UM LIST OF FIGURES Figure Number Title Page 1-1 IE-78K0S-NS System Configuration............................................................................................................... 12 1-2 Basic Hardware Configuration of IE-78K0S-NS ............................................................................................. 13 2-1 Main Board (G-789000 Board) ....................................................................................................................... 17 3-1 Connecting Emulation Board (When using an emulation board on which P1, P2, and P3 connectors are mounted) .................................. 19 3-2 Connecting Emulation Board (When using an emulation board on which CN5, CN6, CN7, and CN8 connectors are mounted)................. 20 3-3 Connecting Emulation Probe.......................................................................................................................... 21 3-4 Connecting AC Adapter.................................................................................................................................. 22 3-5 Connecting Dedicated Bus Interface Cable.................................................................................................... 22 3-6 Default Settings of SW2, SW3, SW4, JP1, and JP4 ...................................................................................... 24 3-7 Part Names of G-789000 Board ..................................................................................................................... 25 A-1 Mounting of PCI Board and Connector Boards .............................................................................................. 27 C-1 INT JP, WAIT JP Settings .............................................................................................................................. 32 D-1 INT JP, WAIT JP Settings .............................................................................................................................. 35 User's Manual U13549EJ2V0UM 9 LIST OF TABLES Table Number Title Page 1-1 List of Functions (MAX. Specifications) ..........................................................................................................14 3-1 Electrical Characteristics ................................................................................................................................23 C-1 SW1 and SW2 Settings When Setting I/O Address to 01DxH........................................................................31 D-1 SW1 and SW2 Settings When Setting I/O Address to 020xH ........................................................................34 10 User's Manual U13549EJ2V0UM CHAPTER 1 GENERAL The IE-78K0S-NS is a development tool for effectively debugging hardware and software using a 78K/0S Series 8bit single-chip microcontroller. This chapter describes the system configuration and basic specifications of the IE-78K0S-NS. 1.1 System Configuration Figure 1-1 shows the system configuration of the IE-78K0S-NS. User's Manual U13549EJ2V0UM 11 CHAPTER 1 GENERAL Figure 1-1. IE-78K0S-NS System Configuration Device fileNote 1 (Available separately) Integrated debugger ID78K0S-NS (Sold separately) Control software Host machine PC-9800 Series or IBM PC/ATTM and compatibles Interface board IE-70000-98-IF-C (Sold separately) Interface board IE-70000-PC-IF-C (Sold separately) Interface board IE-70000-PCI-IF-A (Sold separately) Interface card Interface cable or Interface cable (NS interface cable) IE-78K0S-NS (This product) In-circuit emulator NS card cable FG Cable MC card cableNote 2 IE-70000-CD-IF-A (Sold separately) Emulation board IE-789xxx-NS-EM1 (Sold separately) AC adapter IE-70000-MC-PS-B (Sold separately) Emulation probe NP-xxxxxNote 3 (Sold separately) Conversion socket EV-xxxxxx-xxxNote 4 (Sold separately) TQx-xxxxxxNote 5 (Sold separately) Notes 1. The device file can be downloaded from the Web site of NEC Electron Devices (http://www.ic.nec.co.jp/micro/) TM 2. This cable is used for the V850 Series . It cannot be used for the IE-78K0S-NS. 3. The NP-xxxxx is a product of Naito Densei Machida Mfg. Co., Ltd. (TEL +81-45-475-4191). Contact an NEC distributor when purchasing. 4. The EV-xxxxxx-xxx is a product of NEC. 5. The TQx-xxxxxx is a product of TOKYO ELETECH CORPORATION. Inquiries: Daimaru Kogyo, Co., Ltd. Tokyo Electronics Department (TEL: +81-3-3820-7112) Osaka Electronics Department (TEL: +81-6-6244-6672) 12 User's Manual U13549EJ2V0UM CHAPTER 1 GENERAL 1.2 Hardware Configuration The IE-78K0S-NS consists of the following hardware units (such as cabinet and boards). * Cabinet * 78K0S main board * NS interface cable Figure 1-2. Basic Hardware Configuration of IE-78K0S-NS IE-78K0S-NS (This product) IE-789xxx-NS-EM1 Interface board (Sold separately) Host machine Dedicated bus interface 78K0S main board Emulation board IE-789xxx-NS-EM1 (Sold separately) Interface card (Sold separately) Emulation probe (Sold separately) User's Manual U13549EJ2V0UM 13 CHAPTER 1 GENERAL 1.3 Basic Specifications Table 1-1. List of Functions (MAX. Specifications) Parameter Description TM Supervisor V40 (operating frequency: 16.0 MHZ) Target device 78K0S Series (PD789xxx) System clock Clock supply Same as target device External Pulse input Internal Mounted on IE-789xxx-NS-EM1 Substitute memory capacity 64 KB Mapping unit Internal ROM 256 bytes Internal high-speed RAM 8 bytes Internal low-speed RAM 64 bytes * Real-time execution * Break execution * Step execution Emulation function Real-time internal RAM monitor All the internal RAM area Event detection * Program execution detection * Bus event detection * External trigger detection Trigger output (x 1) and open-drain output Event integration * Path condition * Trace qualify condition * Delay condition * Trigger condition Break factor * Event break * Manual break * Command break * Fail-safe break Real-time trace Trace factor * All traces * Qualify trace Trace capacity 64-bit x 8 KB Trace contents Address, data, and status Execution time measurement Up to 4 minutes 28 seconds, resolution: 62.5 ns Target interface Emulation probe (sold separately) provided for each target device shape Host interface Dedicated bus interface Low-voltage support Based on the emulation board (sold separately) Host machine PC-9800 Series, or IBM PC/AT and compatibles Power supply DC 5 V Dimensions W235 x D195 x H39 (mm) 14 User's Manual U13549EJ2V0UM CHAPTER 2 PART NAMES This chapter introduces the parts of the IE-78K0S-NS main unit. The packing box contains the IE-78K0S-NS main unit. If there are any missing or damaged items, please contact an NEC sales representative. Please make sure to fill out and return the guarantee card that comes with the main unit. 2.1 Parts of Main Unit (1) Probe end Target system power supply LED T V C C Probe interface (2) Top view R O T LA U M E IT U C IR C IN POWER Power supply LED User's Manual U13549EJ2V0UM 15 CHAPTER 2 PART NAMES (3) Interface DC IN FG - + Power switch (OFF/ON) 16 Dedicated bus interface connector (HOST-I/F) OFF ON RESET HOST-I/F Reset switch (RESET) User's Manual U13549EJ2V0UM CHAPTER 2 2.2 PART NAMES Board Name IE-78K0S-NS contains this board. * Main board (G-789000 Board): 1 Check that you have the correct board. To access the inside of the unit, remove the four screws from the sides of the main unit and open the lid. Figure 2-1. Main Board (G-789000 Board) Remark The above shows the main board mounted in the main unit. User's Manual U13549EJ2V0UM 17 CHAPTER 3 INSTALLATION This chapter describes how to connect the cables to the IE-78K0S-NS and the mode settings. 3.1 Connection Connect the following seven products which are sold separately. Refer to Figure 1-1 System Configuration of IE-78K0S-NS in CHAPTER 1 GENERAL for the system configuration of the IE-78K0S-NS. * IE-70000-98-IF-C: Interface board (use cable that comes with the IE-78K0S-NS) * IE-70000-PC-IF-C: Interface board (use cable that comes with the IE-78K0S-NS) * IE-70000-PCI-IF-A: Interface board (use cable that comes with the IE-78K0S-NS) * IE-70000-CD-IF-A: Interface card (NS card cable and MC card cable are included) * IE-70000-MC-PS-B: AC adapter * IE-789xxx-NS-EM1: Emulation board * NP-xxxxx Note : Emulation probe Note The NP-xxxxx is a product of Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191). Caution Connecting and removing cables or components from the target system and changing the settings of switches, etc. should be carried out after turning off the power of the IE-78K0S-NS main unit and the target system. 18 User's Manual U13549EJ2V0UM CHAPTER 3 INSTALLATION (1) Connecting emulation board (IE-789xxx-NS-EM1) The IE-789xxx-NS-EM1 is sold separately. Figure 3-1. Connecting Emulation Board (When using an emulation board on which P1, P2, and P3 connectors are mounted) <1> Remove the screws from the sides of the main unit, and then remove the top cover. ;; <2> Remove the first plate from the bottom by removing the screws. ; ; ;; ;;; <3> Connect the IE-789xxx-EM1 and fasten the two screws to the emulation board. <4> When using a probe, connect the probe. <5> Connect the top cover and fasten the four screws on the sides. Refer to probe connection (2) Emulation board User's Manual U13549EJ2V0UM 19 CHAPTER 3 INSTALLATION Figure 3-2. Connecting Emulation Board (When using an emulation board on which CN5, CN6, CN7, and CN8 connectors are mounted) <1> Remove the screws from the sides of the main unit, and then remove the top cover. <2> Remove the first and second plates from the bottom by removing the screws. <3> Connect the I/O board and align the spacers that come with the IE-789xxx-NS-EM1 at the <4> Align the probe board with the I/O board and fix by tightening the four connection screws four positions shown below. Supplied spacer Supplied spacer Align Probe board Align I/O Board I/O board Here <5> When using a probe, connect the probe. <6> Connect the top cover and fasten the four screws on the sides. IE-789xxx-NS-EM1 (Probe board) IE-789xxx-NS-EM1 (I/O board) Refer to probe connection (2) 20 User's Manual U13549EJ2V0UM CHAPTER 3 INSTALLATION (2) Connecting emulation probe (NP-xxxxx) The NP-xxxxx is sold separately. Figure 3-3. Connecting Emulation Probe Emulation probe (NP-xxxxx) Emulation board (IE-789xxx-NS-EM1) Main board (G-789000 Board) Caution The emulation probe (NP-xxxxx) mounting location varies depending on the model of the IE789xxx-NS-EM1 in use. For details, refer to the IE-789xxx-NS-EM1 User's Manual. User's Manual U13549EJ2V0UM 21 CHAPTER 3 INSTALLATION (3) Connecting AC adapter (IE-70000-MC-PS-B) IE-70000-MC-PS-B is sold separately. <1> Insert the AC adapter plug into the DC IN socket of the IE-78K0S-NS. Figure 3-4. Connecting AC Adapter Dedicated bus interface connector (HOST-I/F) DC IN FG - + OFF ON RESET HOST-I/F Power switch (OFF/ON) Reset switch (RESET) (4) Connecting interface cable <1> Insert the cable into the bus interface connector on the IE-78K0S-NS main unit. Figure 3-5. Connecting Dedicated Bus Interface Cable Dedicated bus interface connector (HOST-I/F) DC IN FG - + OFF ON RESET HOST-I/F Power switch (OFF/ON) Reset switch (RESET) Caution The type of interface cable varies depending on the interface board and interface card. * When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF-A) Connect the NS interface cable that comes with the IE-78K0S-NS. * When using an interface card (IE-70000-CD-IF-A) Connect the NS card cable that comes with the IE-70000-CD-IF-A. The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF-A, and IE-70000-CD-IF-A are sold separately. 22 User's Manual U13549EJ2V0UM CHAPTER 3 INSTALLATION 3.2 External Trigger Functions (1) EXTOUT At the occurrence of a break event, the EXTOUT pin on the emulation board (IE-789xxx-NS-EM1) outputs a low level for 1.3 s. Caution Because the output is open drain, connect a pull-up resistor in the target system. (2) EXTIN The EXTIN pin on the emulation board (IE-789xxx-NS-EM1) can be used to input an event signal. Enter highlevel pulse signals for two or more CPU clocks. Caution For the electrical characteristics, refer to Table 3-1. Table 3-1. Electrical Characteristics Parameter MIN. [V] High-level input voltage Target voltage x 0.7 Low-level input voltage 0 User's Manual U13549EJ2V0UM MAX. [V] Target voltage Target voltage x 0.3 23 CHAPTER 3 INSTALLATION 3.3 Jumper or Switch Settings (on Main Board (G-789000 Board)) (1) Default settings of Jumper or Switch Figure 3-6. Default Settings of SW2, SW3, SW4, JP1, and JP4 7 6 OFF 5 4 3 2 1 1 2 3 4 OFF 5 6 7 8 SW4 8 SW3 1 2 3 1 JP1 JP4 SW2 (Push button): Reset SW3 (DIP switch): ON (fixed) SW4 (DIP switch): ON (fixed) JP1: 2 and 3 shorted JP4: 1 and 2 shorted JP2 and JP3 are not used. 24 2 User's Manual U13549EJ2V0UM 3 CHAPTER 3 INSTALLATION Figure 3-7. Part Names of G-789000 Board Dedicated bus interface connector (HOST-I/F) SW2 JK1 CN4 CN7 SW1 CN5 P3 P1 P2 JP1 CN8 CN6 JP4 SW3 SW4 User's Manual U13549EJ2V0UM 25 APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC This chapter describes the setting method when connecting the IE-78K0S-NS. For details, refer to the IE-70000-PCI-IF-A User's Manual (to be prepared). A.1 Introduction The IE-70000-PCI-IF-A is an interface board that is installed in the PCI bus slot of a PC incorporating Windows TM 95/98 or Windows NT4.0/2000. First of all, check that you have the following items. * Interface board (IE-70000-PCI-IF-A) for desktop PC x 1 * 8-bit connector board (connected to IE-70000-PCI-IF-A) x 1 * 32-bit connector board x 1 * User's manual x 1 * DLL-DISK x 1 * IE-PC Driver DISK x 1 * Guarantee card x 1 <Basic specifications> Applicable models The IE-70000-PCI-IF-A is designed for devices incorporating Windows 95/98 or Windows NT 4.0/2000 and that provide a PCI bus slot. Hardware resources used * I/O address .........0000H to FFFFH * Interrupts ............Unused * Memory...............Uses 80H bytes Current consumption 300 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 26 User's Manual U13549EJ2V0UM APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC A.2 Installation (1) Board settings There are no jumpers or DIP switches on the IE-70000-PCI-IF-A. (2) 8-bit connector board mounting An 8-bit connector board is premounted at shipment. Remark When a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector (refer to Figure A-1) and fasten them together with screws. Caution The 32-bit connector board is included for future function expansion. Figure A-1. Mounting of PCI Board and Connector Boards Combination connector 32-bit connector board Combination connector Combination connector CH1 PCI board CH0 8-bit connector board (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the PCI bus slot following the instructions in the PC's manual. At installation, fasten the PCI board to the PC with screws. (4) IE-PC Driver installation Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation. (5) Connecting with IE-78K0S-NS Using the supplied cable, connect the IE-78K0S-NS to the CH0 side. Caution Connection with the IE-78K0S-NS is possible on the CH0 side only. User's Manual U13549EJ2V0UM 27 APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) This chapter describes the setting method when connecting the IE-78K0S-NS. For details, refer to the IE-70000-CD-IF-A User's Manual (to be prepared). B.1 Introduction The PC card interface (IE-70000-CD-IF-A) is an interface card for an IE product that is installed in the PCMCIA2.1/JEIDA standard Ver. 4.2-compliant PC card slot of a PC incorporating Windows 95/98 or Windows NT 4.0/2000. First of all, check that you have the following items. * PC card interface (IE-70000-CD-IF-A) x 1 * MC-A CABLE x 1 * NS-A CABLE x 1 * User's manual x 1 * DLL-DISK x 1 * IE-PC Driver DISK x 1 * Guarantee card x 1 <Basic specifications> Applicable models The IE-70000-CD-IF-A is designed for devices incorporating Windows 95/98 or Windows NT4.0/2000 and that provide a PC card slot compliant with PCMCIA2.1/JEIDA standard Ver.4.2. Hardware resources used * I/O address .........20H bytes starting from 220H, 260H, 2E0H, 320H, or 3E0H as a base address * Interrupts ............Unused * Memory...............Unused Current consumption 300 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 28 User's Manual U13549EJ2V0UM APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) B.2 Installation (1) Installation in PC For Windows 95/98/2000, insert the PCMCIA card in the card slot when the power supply of the PC is turned on. For Windows NT 4.0, insert the card in the slot when the power supply is turned off. Be careful to insert the card in the correct direction. (2) IE-PC Driver installation Refer to the supplied IE-PC Driver DISK Readme_e.txt for PCMCIA driver installation. Caution This interface card cannot be connected to the IE-78xxxx xxxx-R. xxxx Actually, installation ends completely by selecting "IE-78xxxx xxxx-R" displayed in the IE-PC Driver DISK installation menu. In xxxx this case, however, the installation is invalid. (3) Connection with the IE-78K0S-NS-A Using the NS-A CABLE, connect the IE-70000-CD-IF-A to the IE-78K0S-NS. Caution Be sure to use the NS-A CABLE when connecting to the IE-78K0S-NS-A. If MC-A CABLE is used, the IE-70000-CD-IF-A may be damaged. User's Manual U13549EJ2V0UM 29 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES) This chapter describes the setting method when connecting the IE-78K0S-NS. For details, refer to the IE-70000-98-IF-C User's Manual (to be prepared). C.1 Introduction The IE-70000-98-IF-C is an interface board for the PC-9800 series (except for NX series) that is installed in the C bus slot of a PC-9800 series (except for NX series) machine. Caution The PC98-NX series is treated as an IBM PC/AT compatible machine. Refer to APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC. First of all, check that you have the following items. * Interface board (IE-70000-98-IF-C) for PC-9800 series x 1 * User's manual x 1 * DLL-DISK x 1 * IE-PC Driver DISK x 1 * Guarantee card x 1 <Basic specifications> Applicable models This product is designed for devices incorporating Windows 95/98 or Windows NT 4.0/2000 with an on-chip PC9800 series C bus. Hardware resources used * I/O addresses .............. 16 bytes in a 256-byte boundary (00DxH, 01DxH,...FFDxH) * Interrupts and others ... Unused Current consumption 500 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. 30 User's Manual U13549EJ2V0UM APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES) C.2 Installation (1) I/O address settings SW1 and SW2 are the switches selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15. In the IE-78K0S-NS, the addresses should be set in the 16 bytes between 00DxH and FFDxH. The switch takes the value "0" when ON and "1" when OFF. The addresses used for setup must be values that are not used in the PC system or for other boards. In addition, since these values are used during software installation, make a note of them for future reference. Setting examples of I/O address, SW1 and SW2 are shown below. Table C-1. SW1 and SW2 Settings When Setting I/O Address to 01Dx xH SW1 Number Address 1 2 3 4 5 6 7 8 A4 A5 A6 A7 A8 A9 A10 A11 0 0 0 0 ON OFF 1 SW2 Number 1 Address ON OFF Caution 1 1 1 2 3 4 5 6 7 8 A12 A13 A14 A15 OFF OFF ON OFF 0 0 0 0 0 1 1 1 Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF. User's Manual U13549EJ2V0UM 31 APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES) (2) Jumper settings The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers. In the IE-78K0S-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted. Figure C-1. INT JP, WAIT JP Settings 1 2 1 NO USE 2 3 Shorted IR3 WAIT JP IR5 IR6 : Shorted IR9 IR11 IR12 IR13 INT JP (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the C bus slot following the instructions in the PC's manual. At installation, fasten the interface board to the PC with screws. (4) IE-PC Driver installation Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation. (5) Connecting with IE-78K0S-NS Using the supplied cable, connect the IE-78K0S-NS to CH0. Caution Connection with the IE-78K0S-NS is possible to CH0 only. For connection with other models, refer to their respective manuals. 32 User's Manual U13549EJ2V0UM APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES This chapter describes the setting method when connecting the IE-78K0S-NS. For details, refer to the IE-70000-PC-IF-C User's Manual (to be prepared). D.1 Introduction The IE-70000-PC-IF-C is an interface board for IBM PC/AT and compatibles and is installed in the ISA bus slot of IBM PC/AT and compatibles. First of all, check that you have the following items. * Interface board (IE-70000-PC-IF-C) for IBM PC/AT x 1 * User's manual x 1 * DLL-DISK x 1 * IE-PC Driver DISK x 1 * Guarantee card x 1 <Basic specifications> Applicable models The IE-70000-PC-IF-C is designed for IBM PC/AT and compatibles incorporating Windows 95/98 or Windows NT 4.0/2000 with an on-chip ISA bus. Hardware resources * I/O address.................. 16 bytes in any 16-byte boundary (020xH to 03FxH) * Interrupts and others ... Unused Current consumption 500 mA (MAX. when using +5 V) Cautions 1. Do not place heavy objects on or apply pressure to the board. 2. Do not drop the board or subject it to excessive vibration or shock. 3. When removing a cable, do not pull it by the cord. 4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it is directly exposed to sunlight. 5. Avoid subjecting the board to extreme changes in temperature or humidity. 6. Do not spill drinks or other liquids onto the board or its accessories. 7. Do not connect a cable for a different product to the connector. User's Manual U13549EJ2V0UM 33 APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES D.2 Installation (1) I/O address settings SW1 and SW2 are the switches selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15. In the IE-78K0S-NS, the addresses should be set between 020xH and 03FxH. The switch takes the value "0" when ON and "1" when OFF. The addresses used for setup must be values that are not used in the PC system or for other boards. In addition, since these values are used during software installation, make a note of them for future reference. Setting examples of I/O address, SW1 and SW2 are shown below. Table D-1. SW1 and SW2 Settings When Setting I/O Address to 020x xH SW1 Number Address ON 1 2 3 4 5 6 7 8 A4 A5 A6 A7 A8 A9 A10 A11 0 0 0 0 0 0 0 OFF 1 SW2 Number Address ON OFF Caution 34 1 2 3 4 5 6 7 8 A12 A13 A14 A15 OFF OFF ON OFF 0 0 0 0 0 1 1 1 Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF. User's Manual U13549EJ2V0UM APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES (2) Jumper settings The INT JP and WAIT JP are ISA bus interrupt and WAIT selection jumpers. In the IE-78K0S-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted. Figure D-1. INT JP, WAIT JP Settings 1 2 1 NO USE 2 3 Shorted IRQ2 WAIT JP IRQ3 IRQ4 : Shorted IRQ5 IRQ6 IRQ7 INT JP (3) Installation in PC Make sure that the PC is turned off, then install the interface board in the ISA bus slot following the instructions in the PC's manual. At installation, fasten the interface board to the PC with screws. (4) IE-PC Driver installation Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation. (5) Connecting with IE-78K0S-NS Using the supplied cable, connect the IE-78K0S-NS to CH0. Caution Connection with the IE-78K0S-NS is possible to CH0 only. For connection with other models, refer to their respective manuals. User's Manual U13549EJ2V0UM 35 [MEMO] 36 User's Manual U13549EJ2V0UM [MEMO] User's Manual U13549EJ2V0UM 37 [MEMO] 38 User's Manual U13549EJ2V0UM Facsimile Message From: Name Company Tel. Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation. Please complete this form whenever you'd like to report errors or suggest improvements to us. FAX Address Thank you for your kind support. North America Hong Kong, Philippines, Oceania NEC Electronics Inc. NEC Electronics Hong Kong Ltd. Corporate Communications Dept. Fax: +852-2886-9022/9044 Fax: +1-800-729-9288 +1-408-588-6130 Korea Europe NEC Electronics Hong Kong Ltd. NEC Electronics (Europe) GmbH Seoul Branch Market Communication Dept. Fax: +82-2-528-4411 Fax: +49-211-6503-274 Taiwan NEC Electronics Taiwan Ltd. Fax: +886-2-2719-5951 South America NEC do Brasil S.A. Fax: +55-11-6462-6829 Japan NEC Semiconductor Technical Hotline Fax: +81- 44-435-9608 P.R. China NEC Electronics Shanghai, Ltd. Fax: +86-21-6841-1137 Asian Nations except Philippines NEC Electronics Singapore Pte. Ltd. Fax: +65-250-3583 I would like to report the following error/make the following suggestion: Document title: Document number: Page number: If possible, please fax the referenced page or drawing. Document Rating Excellent Good Acceptable Poor Clarity Technical Accuracy Organization CS 02.3