IE-78K0S-NS - NEC Electronics

Document No. U13549EJ2V0UM00 (2nd edition)

Date Published September 2002 N CP(K)

Printed in Japan

User’s Manual

1998©

IE-78K0S-NS

In-Circuit Emulator

Target Devices

78K/0S Series

User’s Manual U13549EJ2V0UM

[MEMO]

User’s Manual U13549EJ2V0UM 3

V40 and V850 Series are trademarks of NEC Corporation.

Windows is either a registered trademark or trademark of Microsoft Corporation in the United States and/or

other countries.

PC/AT is a trademark of International Business Machines Corporation.

M8E 00. 4

The information in this document is current as of July, 2002. The information is subject to change

without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data

books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products

and/or types are available in every country. Please check with an NEC sales representative for

availability and additional information.

No part of this document may be copied or reproduced in any form or by any means without prior

written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document.

NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of

third parties by or arising from the use of NEC semiconductor products listed in this document or any other

liability arising from the use of such products. No license, express, implied or otherwise, is granted under any

patents, copyrights or other intellectual property rights of NEC or others.

Descriptions of circuits, software and other related information in this document are provided for illustrative

purposes in semiconductor product operation and application examples. The incorporation of these

circuits, software and information in the design of customer's equipment shall be done under the full

responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third

parties arising from the use of these circuits, software and information.

While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers

agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize

risks of damage to property or injury (including death) to persons arising from defects in NEC

semiconductor products, customers must incorporate sufficient safety measures in their design, such as

redundancy, fire-containment, and anti-failure features.

NEC semiconductor products are classified into the following three quality grades:

"Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products

developed based on a customer-designated "quality assurance program" for a specific application. The

recommended applications of a semiconductor product depend on its quality grade, as indicated below.

Customers must check the quality grade of each semiconductor product before using it in a particular

application.

"Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio

and visual equipment, home electronic appliances, machine tools, personal electronic equipment

and industrial robots

"Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster

systems, anti-crime systems, safety equipment and medical equipment (not specifically designed

for life support)

"Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life

support systems and medical equipment for life support, etc.

The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's

data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not

intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness

to support a given application.

(Note)

(1) "NEC" as used in this statement means NEC Corporation and also includes its majority-owned subsidiaries.

(2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for

NEC (as defined above).

•

User’s Manual U13549EJ2V0UM

Regional Information

Some information contained in this document may vary from country to country. Before using any NEC

product in your application, pIease contact the NEC office in your country to obtain a list of authorized

representatives and distributors. They will verify:

•

Device availability

•

Ordering information

•

Product release schedule

•

Availability of related technical literature

•

Development environment specifications (for example, specifications for third-party tools and

components, host computers, power plugs, AC supply voltages, and so forth)

•

Network requirements

In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary

from country to country.

NEC Electronics Inc. (U.S.)

Santa Clara, California

Tel: 408-588-6000

800-366-9782

Fax: 408-588-6130

800-729-9288

NEC Electronics Hong Kong Ltd.

Hong Kong

Tel: 2886-9318

Fax: 2886-9022/9044

NEC Electronics Hong Kong Ltd.

Seoul Branch

Seoul, Korea

Tel: 02-528-0303

Fax: 02-528-4411

NEC Electronics Shanghai, Ltd.

Shanghai, P.R. China

Tel: 021-6841-1138

Fax: 021-6841-1137

NEC Electronics Taiwan Ltd.

Taipei, Taiwan

Tel: 02-2719-2377

Fax: 02-2719-5951

NEC Electronics Singapore Pte. Ltd.

Novena Square, Singapore

Tel: 253-8311

Fax: 250-3583

NEC do Brasil S.A.

Electron Devices Division

Guarulhos-SP, Brasil

Tel: 11-6462-6810

Fax: 11-6462-6829

J02.4

NEC Electronics (Europe) GmbH

Duesseldorf, Germany

Tel: 0211-65 03 01

Fax: 0211-65 03 327

• Sucursal en España

Madrid, Spain

Tel: 091-504 27 87

Fax: 091-504 28 60

Vélizy-Villacoublay, France

Tel: 01-30-67 58 00

Fax: 01-30-67 58 99

• Succursale Française

• Filiale Italiana

Milano, Italy

Tel: 02-66 75 41

Fax: 02-66 75 42 99

• Branch The Netherlands

Eindhoven, The Netherlands

Tel: 040-244 58 45

Fax: 040-244 45 80

• Branch Sweden

Taeby, Sweden

Tel: 08-63 80 820

Fax: 08-63 80 388

• United Kingdom Branch

Milton Keynes, UK

Tel: 01908-691-133

Fax: 01908-670-290

User’s Manual U13549EJ2V0UM 5

Major Revisions in This Edition

Page Description

Throughout •Addition of interface board IE-70000-PCI-IF-A

•Deletion of interface card IE-70000-CD-IF and addition of IE-70000-CD-IF-A

p.12 Figure 1-1 IE-78K0S-NS System Configuration

•Supply media of debugger ID78K0S-NS changed to CD-ROM

•Addition of Web site where device file can be obtained as Note 1

pp.19 to 21,

24, and 25

CHAPTER 3 INSTALLATION

•Modification of Figure 3-1 Connecting Emulation Board (When using an emulation board on which P1,

P2, and P3 connectors are mounted)

•Modification of Figure 3-2 Connecting Emulation Board (When using an emulation board on which CN5,

CN6, CN7, and CN8 connectors are mounted)

•Modification of Figure 3-3 Connecting Emulation Probe

•Deletion of SW1 from previous edition and addition of SW2 in Figure 3-6 Default Settings of SW2, SW3,

SW4, JP1, and JP4

•Addition of CN4 and SW2 in Figure 3-7 Part Names of G-789000 Board

pp.26 and 27 Addition of APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC

pp.28 and 29 Deletion of previous APPENDIX C PC CARD INTERFACE (IE-70000-CD-IF)

Addition of APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)

pp.30 to 32 Modification of APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR

NX SERIES)

pp.33 to 35 Modification of APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

The mark shows major revised points.

User’s Manual U13549EJ2V0UM

INTRODUCTION

Product overview

The IE-78K0S-NS is used in combination with an emulation board (IE-789×××-NS-EM1) to debug products

in the 78K/0S Series of 8-bit single-chip microcontrollers.

Readers

This manual is intended for engineers who perform debugging of systems that use products in the 78K/0S

Series of 8-bit single-chip microcontrollers, using the IE-78K0S-NS and an emulation board (IE-789×××-NS-

EM1).

Purpose

The purpose of this manual is to help the reader understand the debugging functions that are available by

using the IE-78K0S-NS and an emulation board (IE-789×××-NS-EM1) together.

Organization

When using the IE-78K0S-NS, please refer to the manual (this manual) that comes with the IE-78K0S-NS as

well as the manual that comes with the emulation board (IE-789×××-NS-EM1).

• Basic specifications • Function outline

• System configuration • Target interface differences

• External interface function

How to read this manual

To understand the overall functions of the IE-78K0S-NS

→ Read this manual in the order of the CONTENTS.

To understand the basic specifications

→ Refer to CHAPTER 1 GENERAL and CHAPTER 2 PART NAMES.

For how to connect the IE-789×××-NS-EM1 and make settings to debug 78K/0S Series products

→ Refer to CHAPTER 3 INSTALLATION.

IE-78K0S-NS

User’s Manual

(This manual)

IE-789×××-NS-EM1

User’s Manual

User’s Manual U13549EJ2V0UM 7

Terminology

The meanings of the terms used in this manual are described in the table below.

Terms Meaning

Emulation device This is a general term for the device in the emulator that is used to emulate the target device.

It includes the emulation CPU.

Emulation CPU This is the CPU block in the emulator that is used to execute user-generated programs.

Target device This is the device to be emulated.

Target system This is the system to be debugged.

It includes the target program and the hardware created by the user. When defined narrowly, it includes

only the hardware.

Conventions

Data significance: Higher digits on the left and lower digits on the right

Note: Footnote for item marked with Note in the text

Caution: Information requiring particular attention

Remark: Supplementary information

User’s Manual U13549EJ2V0UM

CONTENTS

CHAPTER 1 GENERAL.......................................................................................................................... 11

1.1 System Configuration .............................................................................................................. 11

1.2 Hardware Configuration .......................................................................................................... 13

1.3 Basic Specifications ................................................................................................................ 14

CHAPTER 2 PART NAMES................................................................................................................... 15

2.1 Parts of Main Unit..................................................................................................................... 15

2.2 Board Name .............................................................................................................................. 17

CHAPTER 3 INSTALLATION ................................................................................................................. 18

3.1 Connection................................................................................................................................ 18

3.2 External Trigger Functions...................................................................................................... 23

3.3 Jumper or Switch Settings (on Main Board (G-789000 Board))........................................... 24

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC ............................... 26

A.1 Introduction .............................................................................................................................. 26

A.2 Installation ................................................................................................................................ 27

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A) ................................................................ 28

B.1 Introduction .............................................................................................................................. 28

B.2 Installation ................................................................................................................................ 29

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES

(EXCEPT FOR NX SERIES) ............................................................................................ 30

C.1 Introduction .............................................................................................................................. 30

C.2 Installation ................................................................................................................................ 31

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT

AND COMPATIBLES...................................................................................................... 33

D.1 Introduction .............................................................................................................................. 33

D.2 Installation ................................................................................................................................ 34

User’s Manual U13549EJ2V0UM 9

LIST OF FIGURES

Figure Number Title Page

1-1 IE-78K0S-NS System Configuration............................................................................................................... 12

1-2 Basic Hardware Configuration of IE-78K0S-NS ............................................................................................. 13

2-1 Main Board (G-789000 Board) ....................................................................................................................... 17

3-1 Connecting Emulation Board

(When using an emulation board on which P1, P2, and P3 connectors are mounted) .................................. 19

3-2 Connecting Emulation Board

(When using an emulation board on which CN5, CN6, CN7, and CN8 connectors are mounted)................. 20

3-3 Connecting Emulation Probe.......................................................................................................................... 21

3-4 Connecting AC Adapter.................................................................................................................................. 22

3-5 Connecting Dedicated Bus Interface Cable.................................................................................................... 22

3-6 Default Settings of SW2, SW3, SW4, JP1, and JP4 ...................................................................................... 24

3-7 Part Names of G-789000 Board ..................................................................................................................... 25

A-1 Mounting of PCI Board and Connector Boards .............................................................................................. 27

C-1 INT JP, WAIT JP Settings .............................................................................................................................. 32

D-1 INT JP, WAIT JP Settings .............................................................................................................................. 35

User’s Manual U13549EJ2V0UM

LIST OF TABLES

Table Number Title Page

1-1 List of Functions (MAX. Specifications) ..........................................................................................................14

3-1 Electrical Characteristics ................................................................................................................................23

C-1 SW1 and SW2 Settings When Setting I/O Address to 01D×H........................................................................31

D-1 SW1 and SW2 Settings When Setting I/O Address to 020×H ........................................................................34

User’s Manual U13549EJ2V0UM 11

CHAPTER 1 GENERAL

The IE-78K0S-NS is a development tool for effectively debugging hardware and software using a 78K/0S Series 8-

bit single-chip microcontroller.

This chapter describes the system configuration and basic specifications of the IE-78K0S-NS.

1.1 System Configuration

Figure 1-1 shows the system configuration of the IE-78K0S-NS.

CHAPTER 1 GENERAL

User’s Manual U13549EJ2V0UM

Figure 1-1. IE-78K0S-NS System Configuration

Host machine

PC-9800 Series or

IBM PC/AT

and compatibles

Integrated debugger

ID78K0S-NS

(Sold separately)

Device file

Note 1

(Available separately)

Control software











Interface board

IE-70000-98-IF-C

(Sold separately)

Interface board

IE-70000-PC-IF-C

(Sold separately)

Interface board

IE-70000-PCI-IF-A

(Sold separately)

FG Cable

IE-78K0S-NS

(This product)

Interface cable

(NS interface cable)

In-circuit

emulator

IE-70000-CD-IF-A

(Sold separately)

AC adapter

IE-70000-MC-PS-B

(Sold separately)

Emulation probe

NP-

×××××Note 3

(Sold separately)

Emulation board

IE-789

×××

-NS-EM1 (Sold separately)

Conversion socket

EV-

××××××

×××Note 4

(Sold separately)

××××××Note 5

(Sold separately)

Interface card

NS card

cable

MC card

cable

Note 2

Interface cable

Notes 1. The device file can be downloaded from the Web site of NEC Electron Devices

(http://www.ic.nec.co.jp/micro/)

2. This cable is used for the V850 SeriesTM. It cannot be used for the IE-78K0S-NS.

3. The NP-××××× is a product of Naito Densei Machida Mfg. Co., Ltd. (TEL +81-45-475-4191).

Contact an NEC distributor when purchasing.

4. The EV-××××××-××× is a product of NEC.

5. The TQ×-×××××× is a product of TOKYO ELETECH CORPORATION.

Inquiries: Daimaru Kogyo, Co., Ltd.

Tokyo Electronics Department (TEL: +81-3-3820-7112)

Osaka Electronics Department (TEL: +81-6-6244-6672)

CHAPTER 1 GENERAL

User’s Manual U13549EJ2V0UM 13

1.2 Hardware Configuration

The IE-78K0S-NS consists of the following hardware units (such as cabinet and boards).

• Cabinet

• 78K0S main board

• NS interface cable

Figure 1-2. Basic Hardware Configuration of IE-78K0S-NS

Host

machine

Interface

board

(Sold

separately)

Interface

card

(Sold

separately)

Dedicated

bus interface

78K0S main

board

IE-78K0S-NS

(This product)

Emulation probe

(Sold separately)

Emulation board

IE-789

×××

-NS-EM1

(Sold separately)

IE-789×××-NS-EM1

CHAPTER 1 GENERAL

User’s Manual U13549EJ2V0UM

1.3 Basic Specifications

Table 1-1. List of Functions (MAX. Specifications)

Parameter Description

Supervisor V40TM (operating frequency: 16.0 MHZ)

Target device 78K0S Series (

PD789×××)

System clock Same as target device

External Pulse inputClock supply

Internal Mounted on IE-789×××-NS-EM1

Substitute memory capacity 64 KB

Internal ROM 256 bytes

Internal high-speed

RAM

8 bytes

Mapping

unit

Internal low-speed

RAM

64 bytes

Emulation function • Real-time execution

• Break execution

• Step execution

Real-time internal RAM monitor All the internal RAM area

Event detection • Program execution detection

• Bus event detection

• External trigger detection

Trigger output (× 1) and open-drain output

Event integration • Path condition

• Trace qualify condition

• Delay condition

• Trigger condition

Break factor • Event break

• Manual break

• Command break

• Fail-safe break

Trace factor • All traces

• Qualify trace

Trace capacity 64-bit × 8 KB

Real-time trace

Trace contents Address, data, and status

Execution time measurement Up to 4 minutes 28 seconds, resolution: 62.5 ns

Target interface Emulation probe (sold separately) provided for each target device shape

Host interface Dedicated bus interface

Low-voltage support Based on the emulation board (sold separately)

Host machine PC-9800 Series, or IBM PC/AT and compatibles

Power supply DC 5 V

Dimensions W235 × D195 × H39 (mm)

User’s Manual U13549EJ2V0UM 15

CHAPTER 2 PART NAMES

This chapter introduces the parts of the IE-78K0S-NS main unit.

The packing box contains the IE-78K0S-NS main unit. If there are any missing or damaged items, please contact

an NEC sales representative.

Please make sure to fill out and return the guarantee card that comes with the main unit.

2.1 Parts of Main Unit

(1) Probe end

(2) Top view

T V C C

Target system power supply LED

Probe interface

POWER

IN CIRCUIT EMULATOR

Power supply LED

CHAPTER 2 PART NAMES

User’s Manual U13549EJ2V0UM

(3) Interface

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

CHAPTER 2 PART NAMES

User’s Manual U13549EJ2V0UM 17

2.2 Board Name

IE-78K0S-NS contains this board.

• Main board (G-789000 Board): 1

Check that you have the correct board. To access the inside of the unit, remove the four screws from the sides of

the main unit and open the lid.

Figure 2-1. Main Board (G-789000 Board)

Remark The above shows the main board mounted in the main unit.

User’s Manual U13549EJ2V0UM

CHAPTER 3 INSTALLATION

This chapter describes how to connect the cables to the IE-78K0S-NS and the mode settings.

3.1 Connection

Connect the following seven products which are sold separately.

Refer to Figure 1-1 System Configuration of IE-78K0S-NS in CHAPTER 1 GENERAL for the system

configuration of the IE-78K0S-NS.

• IE-70000-98-IF-C: Interface board (use cable that comes with the IE-78K0S-NS)

• IE-70000-PC-IF-C: Interface board (use cable that comes with the IE-78K0S-NS)

• IE-70000-PCI-IF-A: Interface board (use cable that comes with the IE-78K0S-NS)

• IE-70000-CD-IF-A: Interface card (NS card cable and MC card cable are included)

• IE-70000-MC-PS-B: AC adapter

• IE-789×××-NS-EM1: Emulation board

• NP-×××××Note: Emulation probe

Note The NP-××××× is a product of Naito Densei Machida Mfg. Co., Ltd. (TEL: +81-45-475-4191).

Caution Connecting and removing cables or components from the target system and changing the

settings of switches, etc. should be carried out after turning off the power of the IE-78K0S-NS

main unit and the target system.

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM 19

(1) Connecting emulation board (IE-789×××

××××××

×××-NS-EM1)

The IE-789×××-NS-EM1 is sold separately.

Figure 3-1. Connecting Emulation Board

(When using an emulation board on which P1, P2, and P3 connectors are mounted)

<1> Remove the screws from the sides of the

main unit, and then remove the top cover.

<2> Remove the first plate from the bottom by

removing the screws.

;;

<3> Connect the IE-789×××-EM1 and fasten the

two screws to the emulation board.

;;;

;;

;

<4> When using a probe, connect the probe. <5> Connect the top cover and fasten the four

screws on the sides.

Emulation board

Refer to probe connection (2)

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM

Figure 3-2. Connecting Emulation Board

(When using an emulation board on which CN5, CN6, CN7, and CN8 connectors are mounted)

<1> Remove the screws from the sides of the main

unit, and then remove the top cover.

<2> Remove the first and second plates from the

bottom by removing the screws.

<3> Connect the I/O board and align the spacers

that come with the IE-789×××-NS-EM1 at the

four positions shown below.

<4> Align the probe board with the I/O board and fix

by tightening the four connection screws

I/O Board

Supplied

spacer

Align

Supplied

spacer

Align

Here

Probe board

I/O board

<5> When using a probe, connect the probe. <6> Connect the top cover and fasten the four

screws on the sides.

Refer to probe connection (2)

IE-789×××-NS-EM1 (Probe board)

IE-789×××-NS-EM1 (I/O board)

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM 21

(2) Connecting emulation probe (NP-×××××

××××××××××

×××××)

The NP-××××× is sold separately.

Figure 3-3. Connecting Emulation Probe

Emulation probe

(NP-×××××)

Emulation board

(IE-789×××-NS-EM1)

Main board

(G-789000 Board)

Caution The emulation probe (NP-×××××

××××××××××

×××××) mounting location varies depending on the model of the IE-

789×××

××××××

×××-NS-EM1 in use. For details, refer to the IE-789×××

××××××

×××-NS-EM1 User’s Manual.

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM

(3) Connecting AC adapter (IE-70000-MC-PS-B)

IE-70000-MC-PS-B is sold separately.

<1> Insert the AC adapter plug into the DC IN socket of the IE-78K0S-NS.

Figure 3-4. Connecting AC Adapter

(4) Connecting interface cable

<1> Insert the cable into the bus interface connector on the IE-78K0S-NS main unit.

Figure 3-5. Connecting Dedicated Bus Interface Cable

Caution The type of interface cable varies depending on the interface board and interface card.

• When using an interface board (IE-70000-98-IF-C, IE-70000-PC-IF-C, or IE-70000-PCI-IF-A)

→ Connect the NS interface cable that comes with the IE-78K0S-NS.

• When using an interface card (IE-70000-CD-IF-A)

→ Connect the NS card cable that comes with the IE-70000-CD-IF-A.

The IE-70000-98-IF-C, IE-70000-PC-IF-C, IE-70000-PCI-IF-A, and IE-70000-CD-IF-A are sold separately.

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

FG OFF ON RESET HOST-I/F

DC IN

Reset switch

(RESET)

Dedicated bus interface connector

(HOST-I/F)

Power switch

(OFF/ON)

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM 23

3.2 External Trigger Functions

(1) EXTOUT

At the occurrence of a break event, the EXTOUT pin on the emulation board (IE-789×××-NS-EM1) outputs a low

level for 1.3

Caution Because the output is open drain, connect a pull-up resistor in the target system.

(2) EXTIN

The EXTIN pin on the emulation board (IE-789×××-NS-EM1) can be used to input an event signal. Enter high-

level pulse signals for two or more CPU clocks.

Caution For the electrical characteristics, refer to Table 3-1.

Table 3-1. Electrical Characteristics

Parameter MIN. [V] MAX. [V]

High-level input voltage Target voltage × 0.7 Target voltage

Low-level input voltage 0 Target voltage × 0.3

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM

3.3 Jumper or Switch Settings (on Main Board (G-789000 Board))

(1) Default settings of Jumper or Switch

Figure 3-6. Default Settings of SW2, SW3, SW4, JP1, and JP4

SW3

JP1

2345

OFF

678

SW4

JP4

2345

OFF

678

SW2 (Push button): Reset

SW3 (DIP switch): ON (fixed)

SW4 (DIP switch): ON (fixed)

JP1: 2 and 3 shorted

JP4: 1 and 2 shorted

JP2 and JP3 are not used.

CHAPTER 3 INSTALLATION

User’s Manual U13549EJ2V0UM 25

Figure 3-7. Part Names of G-789000 Board

CN7

JK1

SW1

CN5

JP1

CN6

SW3JP4 SW4

CN8

Dedicated bus interface connector

(HOST-I/F)

CN4

SW2

User’s Manual U13549EJ2V0UM

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC

This chapter describes the setting method when connecting the IE-78K0S-NS.

For details, refer to the IE-70000-PCI-IF-A User’s Manual (to be prepared).

A.1 Introduction

The IE-70000-PCI-IF-A is an interface board that is installed in the PCI bus slot of a PC incorporating WindowsTM

95/98 or Windows NT4.0/2000.

First of all, check that you have the following items.

• Interface board (IE-70000-PCI-IF-A) for desktop PC × 1

• 8-bit connector board (connected to IE-70000-PCI-IF-A) × 1

• 32-bit connector board × 1

• User’s manual × 1

• DLL-DISK × 1

• IE-PC Driver DISK × 1

• Guarantee card × 1

Applicable models

The IE-70000-PCI-IF-A is designed for devices incorporating Windows 95/98 or Windows NT 4.0/2000 and that

provide a PCI bus slot.

Hardware resources used

• I/O address .........0000H to FFFFH

• Interrupts ............Unused

• Memory...............Uses 80H bytes

Current consumption

300 mA (MAX. when using +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, do not pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it

is directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Do not spill drinks or other liquids onto the board or its accessories.

7. Do not connect a cable for a different product to the connector.

APPENDIX A INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC

User’s Manual U13549EJ2V0UM 27

A.2 Installation

(1) Board settings

There are no jumpers or DIP switches on the IE-70000-PCI-IF-A.

(2) 8-bit connector board mounting

An 8-bit connector board is premounted at shipment.

Remark When a 32-bit board is mounted, place it on the 8-bit connector board using the combination connector

(refer to Figure A-1) and fasten them together with screws.

Caution The 32-bit connector board is included for future function expansion.

Figure A-1. Mounting of PCI Board and Connector Boards

CH1 CH0

PCI board

32-bit connector board

Combination connector

8-bit connector board

(3) Installation in PC

Make sure that the PC is turned off, then install the interface board in the PCI bus slot following the instructions in

the PC’s manual.

At installation, fasten the PCI board to the PC with screws.

(4) IE-PC Driver installation

Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation.

(5) Connecting with IE-78K0S-NS

Using the supplied cable, connect the IE-78K0S-NS to the CH0 side.

Caution Connection with the IE-78K0S-NS is possible on the CH0 side only.

User’s Manual U13549EJ2V0UM

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)

This chapter describes the setting method when connecting the IE-78K0S-NS.

For details, refer to the IE-70000-CD-IF-A User’s Manual (to be prepared).

B.1 Introduction

The PC card interface (IE-70000-CD-IF-A) is an interface card for an IE product that is installed in the

PCMCIA2.1/JEIDA standard Ver. 4.2-compliant PC card slot of a PC incorporating Windows 95/98 or Windows NT

4.0/2000.

First of all, check that you have the following items.

• PC card interface (IE-70000-CD-IF-A) × 1

• MC-A CABLE × 1

• NS-A CABLE × 1

• User’s manual × 1

• DLL-DISK × 1

• IE-PC Driver DISK × 1

• Guarantee card × 1

Applicable models

The IE-70000-CD-IF-A is designed for devices incorporating Windows 95/98 or Windows NT4.0/2000 and that

provide a PC card slot compliant with PCMCIA2.1/JEIDA standard Ver.4.2.

Hardware resources used

• I/O address .........20H bytes starting from 220H, 260H, 2E0H, 320H, or 3E0H as a base address

• Interrupts ............Unused

• Memory...............Unused

Current consumption

300 mA (MAX. when using +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, do not pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it

is directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Do not spill drinks or other liquids onto the board or its accessories.

7. Do not connect a cable for a different product to the connector.

APPENDIX B PC CARD INTERFACE (IE-70000-CD-IF-A)

User’s Manual U13549EJ2V0UM 29

B.2 Installation

(1) Installation in PC

For Windows 95/98/2000, insert the PCMCIA card in the card slot when the power supply of the PC is turned on.

For Windows NT 4.0, insert the card in the slot when the power supply is turned off. Be careful to insert the card

in the correct direction.

(2) IE-PC Driver installation

Refer to the supplied IE-PC Driver DISK Readme_e.txt for PCMCIA driver installation.

Caution This interface card cannot be connected to the IE-78××××

××××××××

××××-R. Actually, installation ends

completely by selecting “IE-78××××

××××××××

××××-R” displayed in the IE-PC Driver DISK installation menu. In

this case, however, the installation is invalid.

(3) Connection with the IE-78K0S-NS-A

Using the NS-A CABLE, connect the IE-70000-CD-IF-A to the IE-78K0S-NS.

Caution Be sure to use the NS-A CABLE when connecting to the IE-78K0S-NS-A. If MC-A CABLE is used,

the IE-70000-CD-IF-A may be damaged.

User’s Manual U13549EJ2V0UM

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES

(EXCEPT FOR NX SERIES)

This chapter describes the setting method when connecting the IE-78K0S-NS.

For details, refer to the IE-70000-98-IF-C User’s Manual (to be prepared).

C.1 Introduction

The IE-70000-98-IF-C is an interface board for the PC-9800 series (except for NX series) that is installed in the C

bus slot of a PC-9800 series (except for NX series) machine.

Caution The PC98-NX series is treated as an IBM PC/AT compatible machine. Refer to APPENDIX A

INTERFACE BOARD (IE-70000-PCI-IF-A) FOR DESKTOP PC.

First of all, check that you have the following items.

• Interface board (IE-70000-98-IF-C) for PC-9800 series × 1

• User’s manual × 1

• DLL-DISK × 1

• IE-PC Driver DISK × 1

• Guarantee card × 1

Applicable models

This product is designed for devices incorporating Windows 95/98 or Windows NT 4.0/2000 with an on-chip PC-

9800 series C bus.

Hardware resources used

• I/O addresses .............. 16 bytes in a 256-byte boundary (00D×H, 01D×H,...FFD×H)

• Interrupts and others ... Unused

Current consumption

500 mA (MAX. when using +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, do not pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it

is directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Do not spill drinks or other liquids onto the board or its accessories.

7. Do not connect a cable for a different product to the connector.

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES)

User’s Manual U13549EJ2V0UM 31

C.2 Installation

(1) I/O address settings

SW1 and SW2 are the switches selecting the C bus I/O addresses. SW1 numbers 1 to 8 correspond to C bus

addresses A4 to A11, and SW2 numbers 1 to 4 correspond to C bus addresses A12 to A15.

In the IE-78K0S-NS, the addresses should be set in the 16 bytes between 00D×H and FFD×H. The switch takes

the value “0” when ON and “1” when OFF.

The addresses used for setup must be values that are not used in the PC system or for other boards. In

addition, since these values are used during software installation, make a note of them for future reference.

Setting examples of I/O address, SW1 and SW2 are shown below.

Table C-1. SW1 and SW2 Settings When Setting I/O Address to 01D×

××

×H

SW1 Number12345678

Address A4 A5 A6 A7 A8 A9 A10 A11

ON 0 000

OFF 1 1 1 1

SW2 Number12345678

Address A12 A13 A14 A15 OFF OFF ON OFF

ON 0 000 0

OFF 1 1 1

Caution Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.

APPENDIX C INTERFACE BOARD (IE-70000-98-IF-C) FOR PC-9800 SERIES (EXCEPT FOR NX SERIES)

User’s Manual U13549EJ2V0UM

(2) Jumper settings

The INT JP and WAIT JP are C bus interrupt and WAIT selection jumpers.

In the IE-78K0S-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.

Figure C-1. INT JP, WAIT JP Settings

WAIT JP

: Shorted

INT JP

ShortedNO USE

IR3

IR5

IR6

IR9

IR11

IR12

IR13

(3) Installation in PC

Make sure that the PC is turned off, then install the interface board in the C bus slot following the instructions in

the PC’s manual.

At installation, fasten the interface board to the PC with screws.

(4) IE-PC Driver installation

Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation.

(5) Connecting with IE-78K0S-NS

Using the supplied cable, connect the IE-78K0S-NS to CH0.

Caution Connection with the IE-78K0S-NS is possible to CH0 only.

For connection with other models, refer to their respective manuals.

User’s Manual U13549EJ2V0UM 33

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

This chapter describes the setting method when connecting the IE-78K0S-NS.

For details, refer to the IE-70000-PC-IF-C User’s Manual (to be prepared).

D.1 Introduction

The IE-70000-PC-IF-C is an interface board for IBM PC/AT and compatibles and is installed in the ISA bus slot of

IBM PC/AT and compatibles.

First of all, check that you have the following items.

• Interface board (IE-70000-PC-IF-C) for IBM PC/AT × 1

• User’s manual × 1

• DLL-DISK × 1

• IE-PC Driver DISK × 1

• Guarantee card × 1

Applicable models

The IE-70000-PC-IF-C is designed for IBM PC/AT and compatibles incorporating Windows 95/98 or Windows NT

4.0/2000 with an on-chip ISA bus.

Hardware resources

• I/O address.................. 16 bytes in any 16-byte boundary (020×H to 03F×H)

• Interrupts and others ... Unused

Current consumption

500 mA (MAX. when using +5 V)

Cautions 1. Do not place heavy objects on or apply pressure to the board.

2. Do not drop the board or subject it to excessive vibration or shock.

3. When removing a cable, do not pull it by the cord.

4. Do not use or keep the board in a hot, humid or dusty environment or in a location where it

is directly exposed to sunlight.

5. Avoid subjecting the board to extreme changes in temperature or humidity.

6. Do not spill drinks or other liquids onto the board or its accessories.

7. Do not connect a cable for a different product to the connector.

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

User’s Manual U13549EJ2V0UM

D.2 Installation

(1) I/O address settings

SW1 and SW2 are the switches selecting the ISA bus I/O addresses. SW1 numbers 1 to 8 correspond to ISA

bus addresses A4 to A11, and SW2 numbers 1 to 4 correspond to ISA bus addresses A12 to A15.

In the IE-78K0S-NS, the addresses should be set between 020×H and 03F×H. The switch takes the value “0”

when ON and “1” when OFF.

The addresses used for setup must be values that are not used in the PC system or for other boards. In

addition, since these values are used during software installation, make a note of them for future reference.

Setting examples of I/O address, SW1 and SW2 are shown below.

Table D-1. SW1 and SW2 Settings When Setting I/O Address to 020×

××

×H

SW1 Number12345678

Address A4A5A6A7A8A9A10A11

ON 0 0000 00

OFF 1

SW2 Number12345678

Address A12 A13 A14 A15 OFF OFF ON OFF

ON 0 000 0

OFF 1 1 1

Caution Set SW2 number 7 to ON and SW2 numbers 5, 6, and 8 to OFF.

APPENDIX D INTERFACE BOARD (IE-70000-PC-IF-C) FOR IBM PC/AT AND COMPATIBLES

User’s Manual U13549EJ2V0UM 35

(2) Jumper settings

The INT JP and WAIT JP are ISA bus interrupt and WAIT selection jumpers.

In the IE-78K0S-NS, set INT JP to NO USE, and WAIT JP to 1 and 2 shorted.

Figure D-1. INT JP, WAIT JP Settings

WAIT JP

: Shorted

INT JP

NO USE Shorted

IRQ2

IRQ3

IRQ4

IRQ5

IRQ6

IRQ7

(3) Installation in PC

Make sure that the PC is turned off, then install the interface board in the ISA bus slot following the instructions in

the PC’s manual.

At installation, fasten the interface board to the PC with screws.

(4) IE-PC Driver installation

Refer to the supplied IE-PC Driver DISK Readme_e.txt for IE-PC Driver installation.

(5) Connecting with IE-78K0S-NS

Using the supplied cable, connect the IE-78K0S-NS to CH0.

Caution Connection with the IE-78K0S-NS is possible to CH0 only.

For connection with other models, refer to their respective manuals.

User’s Manual U13549EJ2V0UM

[MEMO]

User’s Manual U13549EJ2V0UM 37

[MEMO]

User’s Manual U13549EJ2V0UM

[MEMO]

Although NEC has taken all possible steps

to ensure that the documentation supplied

to our customers is complete, bug free

and up-to-date, we readily accept that

errors may occur. Despite all the care and

precautions we've taken, you may

encounter problems in the documentation.

Please complete this form whenever

you'd like to report errors or suggest

improvements to us.

Hong Kong, Philippines, Oceania

NEC Electronics Hong Kong Ltd.

Fax: +852-2886-9022/9044

Korea

NEC Electronics Hong Kong Ltd.

Seoul Branch

Fax: +82-2-528-4411

P.R. China

NEC Electronics Shanghai, Ltd.

NEC Electronics Taiwan Ltd.

Fax: +86-21-6841-1137

Address

North America

NEC Electronics Inc.

Corporate Communications Dept.

Fax: +1-800-729-9288

+1-408-588-6130

Europe

NEC Electronics (Europe) GmbH

Market Communication Dept.

Fax: +49-211-6503-274

South America

NEC do Brasil S.A.

Fax: +55-11-6462-6829

Taiwan

Asian Nations except Philippines

NEC Electronics Singapore Pte. Ltd.

Fax: +886-2-2719-5951

Fax: +65-250-3583

Japan

NEC Semiconductor Technical Hotline

Fax: +81- 44-435-9608

I would like to report the following error/make the following suggestion:

Document title:

Document number: Page number:

Thank you for your kind support.

If possible, please fax the referenced page or drawing.

Excellent Good Acceptable PoorDocument Rating

Clarity

Technical Accuracy

Organization

CS 02.3

Name

Company

From:

Tel. FAX

Facsimile

Message