FTLC9551REPM - FINISAR - Datasheet.Live

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 1

Product Specification

100m Parallel MMF 100G QSFP28 Optical Transceiver

FTLC9551REPM

PRODUCT FEATURES

 Hot-pluggable QSFP28 form factor

 Supports 103.1Gb/s aggregate bit

rate

 Power dissipation < 3.5W

 RoHS-6 compliant

 Commercial case temperature range

of 0°C to 70°C

 Single 3.3V power supply

 Maximum link length of 100m on

OM4 Multimode Fiber (MMF)

 4x25Gb/s 850mm VCSEL-based

transmitter

 4x25G electrical interface

 Single MPO12 receptacle

 I2C management interface

APPLICATIONS

 100GBASE-SR4 100G Ethernet

Finisar’s FTLC9551REPM 100G QSFP28 transceiver modules are designed for use in

100 Gigabit Ethernet links over multimode fiber. They are compliant with the QSFP28

MSA1 and IEEE 802.3bm 100GBASE-SR42 and CAUI-42. Digital diagnostics functions

are available via the I2C interface, as specified by the QSFP28 MSA1 and Finisar

Application Note AN-21413. The transceiver is RoHS-6 compliant per Directive

2011/65/EU4 and Finisar Application Note AN-20385.

PRODUCT SELECTION

FTLC9551REPM

R: 100G Ethernet maximum bit rate (103.1Gb/s)

E: 4x25G parallel optics

P: Pull tab release

M: MPO receptacle

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 2

I. Pin Descriptions

Figure 1 – QSFP28-compliant 38-pin connector (per SFF-8679)

Symbol

Name/Description

Notes

1

GND

Ground

1

2

Tx2n

Transmitter Inverted Data Input

3

Tx2p

Transmitter Non-Inverted Data Input

4

GND

Ground

1

5

Tx4n

Transmitter Inverted Data Input

6

Tx4p

Transmitter Non-Inverted Data Input

7

GND

Ground

1

8

ModSelL

Module Select

9

ResetL

Module Reset

10

Vcc Rx

+3.3 V Power supply receiver

11

SCL

2-wire serial interface clock

12

SDA

2-wire serial interface data

13

GND

Ground

1

14

Rx3p

Receiver Non-Inverted Data Output

15

Rx3n

Receiver Inverted Data Output

16

GND

Ground

1

17

Rx1p

Receiver Non-Inverted Data Output

18

Rx1n

Receiver Inverted Data Output

19

GND

Ground

1

20

GND

Ground

1

21

Rx2n

Receiver Inverted Data Output

22

Rx2p

Receiver Non-Inverted Data Output

23

GND

Ground

1

24

Rx4n

Receiver Inverted Data Output

25

Rx4p

Receiver Non-Inverted Data Output

26

GND

Ground

1

27

ModPrsL

Module Present

28

IntL

Interrupt

29

Vcc Tx

+3.3 V Power supply transmitter

30

Vcc1

+3.3 V Power Supply

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 3

31

LPMode

Low Power Mode

32

GND

Ground

1

33

Tx3p

Transmitter Non-Inverted Data Input

34

Tx3n

Transmitter Inverted Data Input

35

GND

Ground

1

36

Tx1p

Transmitter Non-Inverted Data Input

37

Tx1n

Transmitter Inverted Data Input

38

GND

Ground

1

Notes

1. Circuit ground is internally isolated from chassis ground.

II. Absolute Maximum Ratings

Module performance is not guaranteed beyond the operating range (see Section VI).

Exceeding the limits below may damage the transceiver module permanently.

Parameter

Symbol

Min

Typ

Max

Unit

Ref.

Maximum Supply Voltage

Vcc

-0.5

4.0

V

Storage Temperature

TS

-40

85

C

Case Operating Temperature

TOP

-5

75

C

1

Relative Humidity

RH

15

85

%

2

Receiver Damage Threshold, per Lane

PRdmg

3.4

dBm

Notes:

1. 48-hour excursions, maximum

2. Non-condensing.

III. Electrical Characteristics (EOL, TOP = 0 to 70 C, VCC = 3.135 to 3.465 Volts)

Parameter

Symbol

Min

Typ

Max

Unit

Ref.

Supply Voltage

Vcc

3.135

3.465

V

Supply Current

Icc

1.5

A

Module total power

P

3.5

W

1

Transmitter



Signaling rate per lane

25.78125 ± 100ppm

Gb/s

Differential pk-pk input voltage

tolerance

Vin,pp,diff

900

mV

Single-ended voltage tolerance

Vin,pp

-0.35

+3.3

V

Module stress input test

Per Section 83E.3.4.1, IEEE

802.3bm

Receiver



Signaling rate per lane

25.78125 ± 100ppm

Gb/s

Differential data output swing

Vout,pp

100

400

mVpp

2

300

600

400

600

800

600

1200

Eye width

0.57

UI

Eye height, differential

228

mV

Vertical eye closure

VEC

5.5

dB

Transition time (20% to 80%)

tr, tf

12

ps

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 4

Notes:

1. Maximum total power value is specified across the full operational temperature and voltage range

when CDRs are locked or a lack of input signal results in squelch being activated. If incorrect

frequencies cause the CDRs to continuously attempt to lock, maximum power dissipation may reach

4.5 W.

2. Output voltage is settable in 4 discrete ranges via I2C. Default range is Range 2 (400 – 800 mV).

IV. Optical Characteristics (EOL, TOP = 0 to 70C, VCC = 3.135 to 3.465 Volts)

Parameter

Symbol

Min

Typ

Max

Unit

Ref.

Transmitter



Signaling Speed per Lane

25.78125 ± 100ppm

Gb/s

1

Center wavelength

840

850

860

nm

RMS Spectral Width

SW

0.6

nm

Average Launch Power per Lane

TXPx

-8.4

2.4

dBm

Transmit OMA per Lane

TxOMA

-6.4

3

dBm

Launch Power [OMA] minus TDEC

per Lane

P-TDEC

-7.3

dBm

TDEC per Lane

TDEC

4.3

dBm

Optical Extinction Ratio

ER

2

dB

Optical Return Loss Tolerance

ORL

12

dB

Encircled Flux

FLX

>86% at 19 um

<30% at 4.5 um

Average Launch Power of OFF

Transmitter, per Lane

-30

dBm

Transmitter Eye mask definition {X1,

X2, X3, Y1, Y2, Y3}

{0.3,0.38,0.45,0.35,0.41,0.5}

2

Receiver



Signaling Speed per Lane

25.78125 ± 100ppm

GBd

3

Center wavelength

840

860

nm

Damage Threshold

DT

3.4

dBm

Average Receive Power per Lane

RXPx

-10.3

2.4

dBm

4

Receive Power (OMA) per Lane

RxOMA

3

dBm

Receiver Reflectance

Rfl

-12

dB

Stressed Receiver Sensitivity (OMA)

per Lane

SRS

-5.2

dBm

Stressed Conditions:

Stressed Eye Closure

SEC

4.3

dB

Stressed Eye J2 Jitter

J2

0.39

UI

Stressed Eye J4 Jitter

J4

0.53

UI

OMA of each aggressor lane

3

dBm

Stressed Receiver Eye Mask

Definition {X1, X2, X3, Y1, Y2,

Y3}

{0.28,0.5,0.5,0.33,0.33,0.4}

5

LOS De-Assert

LOSD

-13

dBm

LOS Assert

LOSA

-30

dBm

LOS Hysteresis

0.5

2

dB

Notes:

1. Transmitter consists of 4 lasers operating at a maximum speed of 25.78125Gb/s ±100ppm each.

2. Hit Ratio 1.5 x 10-3 hits/sample.

3. Receiver consists of 4 photodetectors operating at a maximum speed of 25.78125Gb/s ±100ppm each.

4. Minimum value is informative only and not the principal indicator of signal strength.

5. Hit Ratio 5 x 10-5 hits/sample.

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 5

V. General Specifications

Parameter

Symbol

Min

Typ

Max

Units

Ref.

Bit Rate (all wavelengths combined)

BR

103.1

Gb/s

1

Bit Error Ratio (pre-FEC)

BER

5x10-5

2

Maximum Supported Distances

Fiber Type

OM3 MMF

Lmax1

70

m

3

OM4 MMF

Lmax2

100

m

3

Notes:

1. Supports 100GBASE-SR4 per IEEE 802.3bm.

2. Tested with a 231 – 1 PRBS.

3. Requires FEC on the host to support maximum distance, per 100GBASE-SR4.

VI. Environmental Specifications

Finisar FTLC9551 QSFP28 transceivers have a commercial operating case temperature

range of 0°C to +70°C. They can support temporary excursions to case temperatures of

-5°C and +75°C without permanent damage (see Section II).

Parameter

Symbol

Min

Typ

Max

Units

Ref.

Case Operating Temperature

Top

0

70

°C

Storage Temperature

Tsto

-40

85

°C

VII. Regulatory Compliance

Finisar FTLC9551 QSFP28 transceivers are Class 1 Laser Products. They are certified

per the following standards:

Feature

Agency

Standard

Laser Eye

Safety

FDA/CDRH

CDRH 21 CFR 1040 and Laser Notice 50

Laser Eye

Safety

TÜV

EN 60825-1:2007

EN 60825-2:2004+A1+A2

Electrical

Safety

TÜV

EN 60950

Electrical

Safety

UL/CSA

CLASS 3862.07

CLASS 3862.87

Copies of the referenced certificates will be available at Finisar upon request.

Complies with FDA performance standards for laser products except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 6

VIII. Digital Diagnostics Functions

FTLC9551 QSFP28 transceivers support the I2C-based diagnostics interface specified by

the QSFP28 MSA1. See Finisar Application Note AN-2141 3.

IX. Memory Contents

Per the QSFP28 MSA1. See Finisar Application Note AN-2141 3.

XI. Mechanical Specifications

Finisar FTLC9551 QSFP28 transceivers are compatible with the QSFP28 MSA

specification1.

Figure 2. FTLC9551REPM Mechanical Dimensions.

Figure 3. Standard Product Label

FTLC9551REPM Product Specification – January 2016

 Finisar Corporation – 7-May-16 Rev. B2 Finisar Page 7

XII. References

1. SFF-8665: “QSFP+ 28Gb/s 4X Pluggable Transceiver Solution (QSFP28)”, Rev 1.9,

June 29, 2015 (and associated SFF documents)

i. SFF-8661

ii. SFF-8679

iii. SFF-8636

iv. SFF-8662

v. SFF-8663

vi. SFF-8672

vii. SFF-8683

2. IEEE 802.3bm, PMD Type 100GBASE-SR4 and CAUI-4.

3. Application Note AN-2141, “100G QSFP28 SR4 NVR Application Note”, Finisar

Corporation.

4. Directive 2011/65/EU of the European Parliament and of the Council, “on the

restriction of the use of certain hazardous substances in electrical and electronic

equipment,” July 1, 2011.

5. “Application Note AN-2038: Finisar Implementation Of RoHS Compliant

Transceivers”, Finisar Corporation, January 21, 2005.

For More Information:

Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1133

Tel. 1-408-548-1000

Fax 1-408-541-6138

sales@finisar.com

www.finisar.com