U62256ASC10LL - Alliance Memory, Inc.

U62256A

August 01, 2002 1 1

F 32768x8 bit static CMOS RAM

F Acces s times 70 ns, 100 ns

F Common data inputs and

data outputs

F Three-state outputs

F Typ. operating supply current

70 ns: 50 mA

100 ns: 40 mA

F TTL/CMOS-compatible

F Autom atical reduct ion of power

dissipation in long Read Cycles

F Power supply voltage 5 V + 10 %

F Operating temperature ranges

0 to 70 °C

-40 to 85 °C

F CECC 90 000 Qual ity Standard

F ESD protection > 2000 V

(MIL STD 883C M3015.7)

F Latch-up immunity >100 mA

F Package: SOP28 (330 mil)

Standard 32K x 8 SRAM

Features

The U62256A is a static RAM

manufactured using a CMOS pro-

cess technology with the following

operating modes:

- Read - Standby

- Write - Data Rete ntion

The memory array is based on a

6-transistor cell.

The circuit is activated by the fal-

ling edge of E. The address and

control inputs open simul taneously.

According to the information of W

and G, the data inputs, or outputs,

are active. In a Read cycle, the

data outputs are activated by the

falling edge of G, afterwards the

data word read will be available at

the outputs DQ0-DQ7. After the

address change, the data outputs

go High-Z until the new information

read is available. The data outputs

have not preferred state.

The Read cycle is finished by the

falling edge of W, or by the rising

edge of E, respectively.

Data retention is guaranteed down

to 2 V. With the exception of E, all

inputs consist of NOR gates, so

that no pull-up/pull-down resistors

are required.

Description

Pin Con fig urat ion

A14 VCC

A12 W

A6 A8

A5 A9

A7 A13

A4 A11

A3 G

A2 A10

DQ1 DQ5

A1 E

A0 DQ7

DQ0 DQ6

DQ2 DQ4

VSS DQ3

Top View

Signal Name Signal Description

A0 - A14 Address Inputs

DQ0 - DQ7 Data In/Out

EChip Enable

GOutput Enable

WWrit e Enable

VCC Power Supply Vol t age

VSS Ground

Pin De sc ri pti on

SOP

U62256A

August 01, 2002

Operating Mode E W G DQ0 - DQ7

Standby/no t selected H * * High-Z

Internal Read L H H High-Z

Read L H L Data Outputs Low-Z

Write L L * Data Inputs High-Z

Trut h Tabl e

Block Diagram

Characteristics

a St resses great er than those listed under „Absolute Maximum Ratings“ may cause permanent damage to the device. This is a stress rating

only, and functional operation of the device at condition above those indicated in the operational sections of this specification is no t im plie d.

Exposure to absolute maximum rating conditions for extended periods may affect reliability

b Maximum voltage is 7 V

c Not more than 1 output should be shorted at the same time. Duration of the short circuit should not exceed 30 s.

All voltages are referenced to VSS = 0 V (ground).

All characteri stic s are valid in the power supply v oltage range and in the operating temperature r ange spe c ified.

Dynamic measurements are based on a r ise and fall time of ≤ 5 ns, measured between 10 % and 90 % of VI, as well as

input levels of VIL = 0 V and VIH = 3 V. The timing r eference level of all input and output signals is 1.5 V,

with th e exception of the tdis-times and ten-t imes, in wh ich cases transition is measured ±200 mV from steady-state voltage.

DQ0

DQ1

DQ2

DQ3

DQ4

DQ5

DQ6

DQ7

VCC VSS W GE

Row Address

Inputs

Column Address

Inputs

Address

Change

Detector

Column Decoder Row Decoder

Se ns e Am plifier /

Write Control Logic

Clock

Generator

Co mmo n Data I/O

Memory Cell

Array

512 Rows x

64 x 8 C olumns

A10

A11

A12

A13

A14

*H or L

Maxim um Rating s aSymbol Min. Max. Unit

Powe r Supply Vo ltage VCC -0.5 7 V

Input Voltage VI-0.5 VCC + 0.5 bV

Out put Voltage VO-0.5 VCC + 0.5 bV

Power Dissipation PD-1W

Operating Temperature C-Type

K-Type Ta0

-40 70

85 °C

Storage Temperatu re Tstg -65 125 °C

Out put Short-Circuit Current

at VCC = 5 V and VO = 0 V c| IOS | 200 mA

U62256A

August 01, 2002 3 3

d -2 V at Pulse Width 30 ns

Recommended

Operating Conditions Symbol Conditions Min. Max. Unit

Power Supply Voltage VCC 4.5 5.5 V

Input Low Vo ltage d VIL -0.3 0.8 V

Input High V ol tage VIH 2.2 VCC + 0.3 V

Electrical Characteri stics Symbol Cond itions Min. Max. Unit

Supply Current - Operating Mode

Supply Current - Standby Mode

(CMOS level)

Supply Current - Standby Mode

(TTL level)

ICC(OP)

ICC(SB)

ICC(SB)1

VCC

VIL

VIH

tcW

VCC

= 5.5 V

= 0.8 V

=2.2 V

= 70 ns

= 100 ns

=5.5 V

= VCC - 0.2 V

≤ 70 °C

≤ 85 °C

= 5.5 V

= 2.2 V

µA

Output High Voltage

Output Low V oltage

VOH

VOL

VCC

IOH

VCC

IOL

= 4.5 V

=-1.0 mA

=4.5 V

=3.2 mA

2.4

0.4

Input High Leakage Current

Input Low Leakage Curren t

IIH

IIL

VCC

VIH

VCC

VIL

= 5.5 V

= 0 V -2

2µA

µA

Output High Current

Output Low Current

IOH

IOL

VCC

VOH

VCC

VOL

=4.5 V

=2.4 V

=4.5 V

=0.4 V 3,2

-1 mA

Output Leakage Current

High at Three-S t ate Outputs

Low at Three-St ate Outputs

IOHZ

IOLZ

VCC

VOH

VCC

VOL

=5.5 V

=0 V -1

1µA

µA

U62256A

August 01, 2002

Switching Characteristics

Read Cycle Symbol 07 10 Unit

Alt. IEC Min. Max. Min. Max.

Read Cycle Time tRC tcR 70 100 ns

Address Access Time to Data Va lid tAA ta(A) 70 100 ns

Chip Enable Access Time to Data Valid tACE ta(E) 70 100 ns

Output Enable Access Time to Data Valid tOE ta(G) 35 45 ns

E HIG H to Ou tp ut in H i g h - Z tHZCE tdis(E) 25 35 ns

G HIGH to Output in High-Z tHZOE tdis(G) 25 35 ns

E LOW to Output in L ow-Z tLZCE ten(E) 55ns

G LOW to Output in Low-Z tLZOE ten(G) 00ns

Output Hold T i m e from Address Change tOH tv(A) 55ns

Switching Characteristics

Write Cycle Symbol 07 10 Unit

Alt. IEC Min. Max. Min. Max.

Write Cycle Time tWC tcW 70 100 ns

Write Pulse Width tWP tw(W) 55 70 ns

Write Pulse Width Setup Time tWP tsu(W) 55 70 ns

Address Setup Ti m e tAS tsu(A) 00ns

Address Valid to End of Write tAW tsu(A-WH) 65 80 ns

Chip Enable Setup T i me tCW tsu(E) 65 80 ns

Pulse Width Chip Enable to End o f Write tCW tw(E) 65 80 ns

Da ta Se tup Time tDS tsu(D) 30 35 ns

Data Hold Time tDH th(D) 00ns

Address Hold from End of Write tAH th(A) 00ns

W LOW to Output in High-Z tHZWE tdis(W) 25 35 ns

G HIGH to Output in High-Z tHZOE tdis(G) 25 35 ns

W HIGH to O u tp u t in L o w -Z tLZWE ten(W) 00ns

G LOW to Output in Low-Z tLZOE ten(G) 00ns

U62256A

August 01, 2002 5 5

Data Retention Mode

E-Controlled

Data Retention

4.5 V

tDR trec

VCC

VCC(DR) ≥ 2 V

0 V

2.2 V

VCC(DR) - 0.2 V ≤ VE(DR) ≤ VCC(DR) + 0.3 V

Data Retention

Characteristics Symbol

Alt. IEC Conditions Min. Typ. Max. Unit

Data Retention Supply Voltage VCC(DR) 25.5V

Data Retention Supply Current ICC(DR) VCC(DR) = 3 V

VE = VCC(DR) - 0. 2 V

Ta ≤ 70 °C

Ta ≤ 85 °C 3

6µA

µA

Data Retention Setup Time tCDR tsu(DR) See Data Retention

W aveforms (above) 0ns

O perating Recovery Ti m e tRtrec tcR ns

Te st Co nf ig urat io n for Funct i onal Che ck

A10

A11

A12

A13

A14

DQ0

DQ1

DQ2

DQ3

DQ4

DQ5

DQ6

DQ7

VIH

VIL

VSS

VCC

5 V

960

30 pF1)

Input level according to the

relevant test measurement

Simultaneous measurement

of all 8 output pins

1)In measurem ent of tdis(E), tdis(W), t dis(G), ten(E), ten(W), ten(G) th e capacitance is 5 pF.

510

U62256A

August 01, 2002

Example

Type

Package Access Time

S = SOP 28 (330 mil) 07 = 70 ns

10 = 100 ns

Operating Temperature Ranges

C = 0 to 70 °C

K = -40 to 85 °C

Capacitance Conditions Symbol Min. Max. Unit

Input Capa citance VCC

= 5.0 V

= VSS

= 1 MHz

= 25 °C

CI-7pF

Out put Capacitance CO-7pF

IC Cod e Numbers

SU62256A 07K

All pins not under test must be connected with ground by capacitors.

The date of manufacture is given by the last 4 digits of the third line of the mark, the first 2 digits indicating the year,

and the last 2 digits the calendar w eek.

Assembl y location and trace code are shown in line 4.

Power Consumption

LL = Very Low Power

Inte rn a l Cod e

U62256A

August 01, 2002 7 7

tdis(G)

tdis(E)

tcR

Previ ous Data Va li d Output Data Valid

Ou tp ut Data Va li d

Address Valid

tsu(A)

High-Z

ten(E)

ten(G)

ta(G)

ta(E)

Read Cycle 1: Ai-controlled (during Read Cycle : E = G = VIL, W = VIH)

Read Cycle 2: G-, E-cont rol l ed ( durin g R ead Cycle: W = VIH)

ta(A)

tcR

tv(A)

DQi

Output

DQi

Output

U62256A

August 01, 2002

Wr ite Cycle1: W-controlled

th(D)

DQi

Input

DQi

Output

tcW

tsu(E) th(A)

tw(W)

tsu(A) tsu(D)

tdis(W) ten(W)

Address Valid

Input Data Valid

High-Z

tsu(A-WH)

Write Cycle 2: E -controlled

Input Data Valid

tsu(A)

th(D)

DQi

Input

DQi

Output

tcW

tw(E)

th(A)

tsu(W)

tsu(D)

tdis(W)

en(E)

High-Z

Ad dres s Va li d

tdis(G)

L- to H - l e v e l undefined H- to L-le ve l

The information describes the type of component and shall not be considered as assured characteristics.Terms of

delivery and rights to chang e design reserved .

U62256A

Zent rum Mikroelekt ronik Dresden AG

Grenzstr aße 28 • D-01109 Dresden • P. O. B. 80 01 34 • D-01101 Dresden • Germ any

Phone: +49 351 8822 306 • Fax: +49 351 8822 337 • Email: sale s@zmd.de • ht tp://ww w.z m d . d e

August 01, 2002

LIFE SUP P O RT POLI CY

ZMD products are not designed, intended, or authorized for use as components in systems intended for surgical

implant into the body, or other applications intended to support or sustain life, or for any other application in which the

failure of the ZM D produc t could create a situation where personal injury or d eat h may occur.

Components used in life-support devices or systems must be expressly authorized by ZMD for such purpose.

LIMITED WARRANTY

The information in this document has been carefully checked and is believed to be reliable. However Zentrum Mikro-

elektronik Dresden AG (ZMD) makes no guarantee or warranty concerning the accuracy of said information and shall

not be responsible for any loss or damage of whatever nature resulting from the use of, or reliance upon it. The infor-

mation in this document describes th e type of component and sh all not be considered as assured charac teristics.

ZMD does not guarantee that the use of any information contained herein will not infringe upon the patent, trade-

mark, copyright, mask work right or other rights of third parties, and no patent or licence is implied hereby. This docu-

ment does not in any way extent ZMD’s warranty on any product beyond that set forth in its standard terms and

conditions of sale.

ZMD reserves terms of delivery and reserves the right to make changes in the products or specifications, or both,

presented in this publication at any time and without notice.