General Description
The PVI5033R Photovoltaic Isolator is a dual-
channel, opto-isolated driver capable of directly driving
gates of power MOSFETs or IGBTs. It utilizes a
monolithic integrated circuit photovoltaic generator of
novel construction as its output. The output is controlled
by radiation from a GaAlAs light emitting diode (LED)
which is optically isolated from the photovoltaic
generator.
The PVI5033R is ideally suited for applications
requiring high-current and/or high voltage switching
with optical isolation between the low-level driving
circuitry and high-energy or high- voltage load circuits.
It can be used for directly driving gates of power
MOSFETs. The dual- channel configuration allows its
outputs to drive independent discrete power
MOSFETs, or be connected in parallel or in series to
provide higher-current drive for power MOSFETs or
higher-voltage drive for IGBTs. PVI5033R employs a
fast turn-off circuitry.
PVI5033R Photovoltaic Isolators are packaged in
an 8-pin, molded DIP package with either thru-hole or
“gull-wing” terminals. It is available in standard plastic
shipping tubes or on tape-and-reel. Refer to Part
Identification information.
Part Identification
PVI5033RPbF thru-hole
PVI5033RSPbF SMT
PVI5033RS-TPbF SMT, Tape and Reel
Features
§Monolithic construction
§3,750 VRMS I/O isolation
§1,200 VDC output-to-output isolation
§Dual-Channel application flexibility
§Solid-State Reliability
§UL Recognized and BABT Certified
§
ÿÿ
Telecommunications
§
ÿÿ
Load Distribution
§
ÿÿ
Industrial Controls
§
ÿÿ
Instrumentation and Measurement
§
ÿÿ
Electronic Ballast
Series PVI5033RPbF
Photovoltaic Isolator
Solid-State
Opto-Isolated MOSFET Gate Driver
Dual-Channel, 5V, 5mA
1 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Applications
2 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI5033RPbF
GENERAL CHARACTERISTICS Limits Units
Min. Dielectric Strength, Input-Output 3750 VRMS
Min. Dielectric Strength, Output-to-Output 1200 VDC
Min. Insulation Resistance, Input-to-Output
@TA=+25°C, 50%RH, 100VDC
Max. Capacitance, Input-Output 5.0 pF
Max. Pin Soldering Temperature (10 seconds max.) +260 °C
Ambient Temperature Range: Operating -40 to +85 °C
Storage -40 to +125 °C
Connection Diagram
1012
5 (-)
6 (+)
7 (-)
8 (+)1
2
3
4
Ω
COUPLED CHARACTERISTICS Limits Units
Min. Output Voltage @ ILED = 10mA, RL = 10MΩ5V
@ TA=0°C to +70°C (See Fig. 1 & 2)
Max. Output Voltage @ ILED = 10mA, RL = 10MΩ10 V
@ TA=0°C to +70°C (See Fig. 1 & 2)
Max. Voltage Differential Between Outputs 1.0 V
@ ILED = 5mA, RL = 10MΩ
Min. Output Short-Circuit Current 1.65 µA
@ ILED = 5mA, @ TA=+25°C (See Fig. 1 & 2)
Typical Output Short-Circuit Current 5 µA
@ ILED = 10mA, @ TA=+25°C (See Fig. 1 & 2)
Max. Turn-On Time @ ILED = 5mA, CLOAD = 200pF (See Fig. 4) 2.5 ms
Max. Turn-Off Time @ ILED = 5mA, CLOAD = 200pF (See Fig. 4) .5 ms
Off-State Clamping Resistance: minimum 350 Ω
maximum 1500 Ω
OUTPUT CHARACTERISTICS Limits Units
Min. Forward Voltage 8.0 VDC
Max. Reverse Current 10 µADC
Electrical Specifications (-40°C ≤ TA ≤ +85°C unless otherwise specified)
INPUT CHARACTERISTICS Limits Units
Min. Input Current (See Fig.1) 5.0 mA
Input Current Range (See Fig. 1) 3.0 to 25 mA
Max. Continuous Input Current @ TA=+25°C 40 mA
LED Forward Voltage Drop @ 5mA, TA=+25°C (See Fig. 3) 1.4 V
Max. Reverse Voltage 6.0 V
Max. Reverse Current @ -6VDC, TA=+25°C 10 µA
International Rectifier does not recommend the use of this
product in aerospace, avionics, military or life support
applications. Users of this International Rectifier product in
such applications assume all risks of such use and in-
demnify International Rectifier against all damages re-
sulting from such use.
3 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI5033RPbF
Figure 1. Typical Output Characteristics Figure 2. Typical Variation of Output
Figure 3. Input Characteristics (Current Controlled) Figure 4. Typical Response Time
16
20
12
8
4
00.5 1.0 1.5 2.00
CAUTION: provide current limiting
so that 25 mA maximum steady-
state control current rating is
not exceeded
Input Current (mA)
LED Forward Voltage Drop (Volts DC) Load Capacitance (pF)
Response Time (μs)
Ambient Temperature (deg. C)
Normalized Output
0 200 400 600 800 1000
7000
6000
5000
4000
3000
2000
1000
0
-40 -20 0 25 40 60 85 100
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
p
Short-Circuit Current
Output Voltage
ILED=5mA
ILED=5mA
Ton
Toff
Min. device and +85 deg. C limit
Max. device and -40 deg. C limit
TYPICAL
Input Current (mA)
Output Short-Circuit Current (μA)
0 5 10 15 20 25 30 35 40
30
27
24
21
18
15
12
9
6
3
0
Output Voltage (VDC)
10
9
8
7
6
5
4
3
2
1
0
RL=10MW
Open Circuit Voltage
Short Circuit Current
5 www.irf.com © 2015 International Rectifier Submit Datasheet Feedback April 24, 2015
Series PVI5033RPbF
Qualification standards can be found at International Rectifiers web site
http://www.irf.com/product-info/reliability
Applicable version of JEDEC standard at the time of product release.
IR WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245, USA
To contact International Rectifier, please visit http://www.irf.com/whoto-call/
PVI5033RPbF N/A
PVI5033RSPbF MSL4
PVI5033RS-TPbF (per JEDEC J-STD-020E & JEDEC J-STD-033C
††
)
RoHS compliant Yes
Qualification information
†
Qualification level
Indusrial
(per JEDEC JESD47I
††
guidelines)
Moisture Sensitivity Level
Revision History
Date Comment
•
Added Qualification Information table on page 5.
•
Updated data sheet based on corporate template.
4/24/2015
